Contents

Routed Bridge Encapsulation with ATM Virtual Circuit Bundles

The Routed Bridge Encapsulation with ATM Virtual Circuit Bundles feature enables routed bridge encapsulation (RBE) over ATM permanent virtual circuit (PVC) bundles. This feature supports PVC bundle member selection based on the quality of service (QoS) group or on the type of service (ToS) or Multiprotocol Label Switching (MPLS) Experimental (EXP) bit in each packet over RBE interfaces. The PVC bundles carry RBE traffic configured on ATM point-to-point subinterfaces.

This feature also supports PVC bundle functionality for ATM adaptation layer 5 (AAL5) multiplexer (MUX) or Logical Link Control (LLC)/Subnetwork Access Protocol (SNAP) encapsulations and ATM PVC bundle scalability.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

Restrictions for Routed Bridge Encapsulation with ATM Virtual Circuit Bundles

The following restrictions apply to the Routed Bridge Encapsulation with ATM Virtual Circuit Bundles feature:

  • RBE over switched virtual circuit (SVC) bundles is not supported.

  • SVC bundle member selection based on QoS groups is not supported.

  • Fast switching is not supported (only Cisco Express Forwarding switching and process switching are supported).

  • PVC bundle member selection based on QoS groups does not support distributed platforms.

  • PVC bundle member selection based on QoS groups does not support bumping, protection, or PVC bundle incompleteness detection.

PVC bundles are supported under the following conditions (numbers are maximum per interface and per router):

  • 1000 PVC bundles with AAL5 LLC/SNAP encapsulation, and each PVC bundle with four PVC bundle members

  • 800 PVC bundles with two members each and with AAL5 LLC/SNAP encapsulation, and interfaces with 4000 PVCs overall (including PVC bundle members)

Information About Routed Bridge Encapsulation with ATM Virtual Circuit Bundles

Benefits of Routed Bridge Encapsulation with ATM Virtual Circuit Bundles

If the Routed Bridge Encapsulation with ATM Virtual Circuit Bundles feature is not configured, you can make the PVC bundle member selection based on ToS bit settings (for IP packets) or EXP bit settings (for MPLS packets). With the Routed Bridge Encapsulation with ATM Virtual Circuit Bundles feature configured, you can make the PVC bundle member selection based on the QoS group value associated with the packet on the ingress before route selection, or on the egress after selecting the adjacency. The packet’s pak_type header is marked with the QoS group to use, based on the generic match criterion provided by the modular QoS (MQC) command-line interface (CLI).

The Routed Bridge Encapsulation with ATM Virtual Circuit Bundles feature gives you the flexibility to choose PVC bundle members based on various criteria. You can define any classification criterion for the traffic, mark the packets matching that criterion with the QoS group, and send them over a specific PVC bundle member to assign the appropriate quality of service to the corresponding class of traffic.

Memory Impact of Routed Bridge Encapsulation with ATM Virtual Circuit Bundles

The additional memory required for configuring the Routed Bridge Encapsulation with ATM Virtual Circuit Bundles feature does not exceed 50 bytes per PVC bundle.

Performance Impact of Routed Bridge Encapsulation with ATM Virtual Circuit Bundles

The Routed Bridge Encapsulation with ATM Virtual Circuit Bundles feature impacts forwarding path performance when PVC bundles are configured with QoS groups. This impact results because, during forwarding, QoS groups must be mapped to the appropriate PVC bundle member index in the array of adjacencies associated with the PVC bundle adjacency.

This feature does not significantly increase CPU usage when traffic at line rates is sent over the PVC bundle (regardless of the selection criterion used for PVC bundle member selection).

How to Configure Routed Bridge Encapsulation with ATM Virtual Circuit Bundles

Specifying the Method for Selecting PVC Bundle Members

Perform this task to specify the method of selection of PVC bundle members. You can specify one of two selection methods:

  • QoS group--Use the QoS group value associated with each packet for selection of PVC bundle members.

  • ToS or EXP--Use ToS bit settings of each packet (for IP packets) or EXP bit settings of each packet (for MPLS packets) for selection of PVC bundle members.

The selection methods are mutually exclusive. This means that when the selection method based on QoS groups is specified on any PVC bundle member, no other selection method is allowed on the same PVC bundle. Similarly, if the selection method based on ToS or EXP is specified on any PVC bundle member, no other selection method is allowed on the same PVC bundle.


Note
  • You can change the selection method from QoS groups to ToS or EXP only if no PVC bundle member has QoS groups or Inverse Address Resolution Protocol (InverseARP) configured.
  • You can change the selection method from ToS or EXP to QoS groups only if no PVC bundle member has precedence, protection, or bumping configured.
SUMMARY STEPS

    1.    enable

    2.    configure terminal

    3.    interface atm slot / port

    4.    bundle bundle-name

    5.    selection-method {qos-group | tos-exp}

    6.    end


DETAILED STEPS
     Command or ActionPurpose
    Step 1 enable


    Example:
    Router> enable
     

    Enables privileged EXEC mode.

    • Enter your password if prompted.

     
    Step 2 configure terminal


    Example:
    Router# configure terminal
     

    Enters global configuration mode.

     
    Step 3 interface atm slot / port


    Example:
    Router(config)# interface atm 2/0
     

    Specifies the ATM interface type and enters interface configuration mode. To determine the correct form of the interface atm command, see your ATM network module, port adapter, or router documentation.

     
    Step 4 bundle bundle-name


    Example:
    Router(config-if)# bundle bundle-test
     

    Creates a PVC bundle or modifies an existing PVC bundle and enters ATM bundle configuration mode.

     
    Step 5 selection-method {qos-group | tos-exp}


    Example:
    Router(config-if-atm-bundle)# selection-method qos-group
     

    Specifies the method for selection of PVC bundle members.

     
    Step 6 end


    Example:
    Router(config-if-atm-member)# end
     

    Ends the configuration session and returns to privileged EXEC mode.

     

    Configuring the QoS Group-Based Method for Selection of PVC Bundle Members

    Perform this task to configure the method for selection of PVC bundle members that is based on QoS groups.

    Before You Begin

    You must associate a QoS group or groups with a PVC bundle member. You can specify a QoS group, a range of QoS groups, or any combination of QoS groups and ranges of QoS groups.

    SUMMARY STEPS

      1.    enable

      2.    configure terminal

      3.    interface atm slot / port

      4.    bundle bundle-name

      5.    selection-method qos-group

      6.    pvc vpi / vci

      7.    qos-group qos-groups

      8.    end


    DETAILED STEPS
       Command or ActionPurpose
      Step 1 enable


      Example:
      Router> enable
       

      Enables privileged EXEC mode.

      • Enter your password if prompted.

       
      Step 2 configure terminal


      Example:
      Router# configure terminal
       

      Enters global configuration mode.

       
      Step 3 interface atm slot / port


      Example:
      Router(config)# interface atm 2/0
       

      Specifies the ATM interface type and enters interface configuration mode.

      • To determine the correct form of the interface atm command, see your ATM network module, port adapter, or router documentation.

       
      Step 4 bundle bundle-name


      Example:
      Router(config-subif)# bundle bundle-test
       

      Creates a PVC bundle or modifies an existing PVC bundle and enters ATM bundle configuration mode.

       
      Step 5 selection-method qos-group


      Example:
      Router(config-if-atm-bundle)# selection-method qos-group
       

      Specifies the method for selection of PVC bundle members based on QoS group.

       
      Step 6 pvc vpi / vci


      Example:
      Router(config-if-atm-bundle)# pvc 1/32
       

      Creates an ATM PVC and enters ATM bundle-member configuration mode.

       
      Step 7 qos-group qos-groups


      Example:
      Router(config-if-atm-member)# qos-group 1
       

      Associates a QoS group or groups with the PVC bundle member.

       
      Step 8 end


      Example:
      Router(config-if-atm-member)# end
       

      Ends the configuration session and returns to privileged EXEC mode.

       

      Configuring Explicit Inverse ARP PVC Selection for QoS Group-Based PVC Bundle Member Selection

      Perform this task to configure explicit Inverse ARP for a PVC bundle member.

      This procedure is optional and provides backward compatibility with existing PVC bundles, in which an Inverse ARP request is sent or expected to be received on the PVC bundle member with precedence 6. If a PVC bundle with selection based on QoS group is connected to an existing PVC bundle, you must follow this procedure to allow Inverse ARP to function. If you do not follow this procedure, Inverse ARP is sent over any of the available PVC bundle members.


      Note

      You can enable Inverse ARP for a PVC bundle member only when using the QoS groups method for selecting PVC bundle members.

      SUMMARY STEPS

        1.    enable

        2.    configure terminal

        3.    interface atm slot / port

        4.    bundle bundle-name

        5.    selection-method qos-group

        6.    pvc vpi / vci

        7.    qos-group qos-groups

        8.    inarp-vc

        9.    end


      DETAILED STEPS
         Command or ActionPurpose
        Step 1 enable


        Example:
        Router> enable
         

        Enables privileged EXEC mode.

        • Enter your password if prompted.

         
        Step 2 configure terminal


        Example:
        Router# configure terminal
         

        Enters global configuration mode.

         
        Step 3 interface atm slot / port


        Example:
        Router(config)# interface atm 2/0
         

        Specifies the ATM interface type and enters interface configuration mode.

        • To determine the correct form of the interface atm command, see your ATM network module, port adapter, or router documentation.

         
        Step 4 bundle bundle-name


        Example:
        Router(config-if)# bundle bundle-test
         

        Creates a bundle or modifies an existing bundle and enters ATM bundle configuration mode.

         
        Step 5 selection-method qos-group


        Example:
        Router(config-if-atm-bundle)# selection-method qos-group
         

        Specifies the method for selection of PVC bundle members based on QoS group.

         
        Step 6 pvc vpi / vci


        Example:
        Router(config-if-atm-bundle)# pvc 1/32
         

        Creates an ATM PVC and enters ATM bundle member configuration mode.

         
        Step 7 qos-group qos-groups


        Example:
        Router(config-if-atm-member)# qos-group 1
         

        Associates a QoS group or groups with the PVC bundle member.

         
        Step 8 inarp-vc


        Example:
        Router(config-if-atm-member)# inarp-vc
         

        Enables Inverse ARP for the PVC bundle member.

         
        Step 9 end


        Example:
        Router(config-if-atm-member)# end
         

        Ends the configuration session and returns to privileged EXEC mode.

         

        Verifying Routed Bridge Encapsulation with ATM Virtual Circuit Bundles

        Perform this task to verify configuration of the Routed Bridge Encapsulation with ATM Virtual Circuit Bundles feature:

        SUMMARY STEPS

          1.    enable

          2.    show atm vc

          3.    show interfaces

          4.    show interfaces virtual-access


        DETAILED STEPS
           Command or ActionPurpose
          Step 1 enable


          Example:
          Router> enable
           

          Enters privileged EXEC mode.

          • Enter your password if prompted.

           
          Step 2 show atm vc


          Example:
          Router# show atm vc
           

          Displays all ATM PVCs and SVCs and their traffic information.

           
          Step 3 show interfaces


          Example:
          Router# show interfaces
           

          Displays interleaving statistics.

          • Interleaving data is displayed only if interleaving occurs.

           
          Step 4 show interfaces virtual-access


          Example:
          Router# show interfaces virtual-access
           

          Displays multilink bundle information.

           

          Configuration Examples for Routed Bridge Encapsulation with ATM Virtual Circuit Bundles

          Specifying the Method for Selecting PVC Bundle Members Example

          The following example shows how to specify the method for selecting PVC bundle members:

          interface atm 2/0
 bundle cisco
  selection-method qos-group
  end

          Configuring the QoS Group-Based Method for Selection of PVC Bundle Members Example

          The following example shows how to configure the QoS group-based method for selection of PVC bundle members:

          interface atm 2/0
 bundle cisco
  selection-method qos-group
  pvc 35/56
  qos-group 1
  end

          Configuring Explicit Inverse ARP PVC Selection for QoS Group-Based PVC Bundle Member Selection Example

          The following example shows how to configure explicit Inverse ARP PVC selection for QoS group-based PVC bundle member selection:

          interface atm 2/0
 bundle cisco
  selection-method qos-group
  pvc 1/32
  qos-group 1
  inarp-vc
  end

          Additional References

          The following sections provide references related to the Routed Bridge Encapsulation with ATM Virtual Circuit Bundles feature.

          Related Documents

          Related Topic

          Document Title

          Broadband access aggregation concepts

          Understanding Broadband Access Aggregation

          Preparing for broadband access aggregation tasks

          Preparing for Broadband Access Aggregation

          Broadband access aggregation and DSL commands: complete command syntax, command mode, defaults, usage guidelines, and examples

          Cisco IOS Broadband Access Aggregation and DSL Command Reference

          Cisco IOS commands

          Cisco IOS Master Commands List, All Releases

          Standards

          Standard

          Title

          None

          --

          MIBs

          MIB

          MIBs Link

          None

          To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at the following URL:

          http:/​/​www.cisco.com/​go/​mibs

          RFCs

          RFC

          Title

          None

          --

          Technical Assistance

          Description

          Link

          The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies.

          To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds.

          Access to most tools on the Cisco Support website requires a Cisco.com user ID and password.

          http:/​/​www.cisco.com/​cisco/​web/​support/​index.html

          Feature Information for Routed Bridge Encapsulation with ATM Virtual Circuit Bundles

          The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

          Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

          Table 1 Feature Information for Routed Bridge Encapsulation with ATM Virtual Circuit Bundles

          Feature Name

          Releases

          Feature Information

          Routed Bridge Encapsulation with ATM Virtual Circuit Bundles

          12.2(31)SB2 12.2(33)SRE 12.4(4)T

          This feature enables RBE over ATM PVC bundles. This feature supports PVC bundle member selection based on the QoS group or on the ToS or MPLS EXP bit in each packet over RBE interfaces.

          The following command was introduced:selection-method.

          Glossary

          ARP --Address Resolution Protocol. Internet protocol used to map an IP address to a MAC address. Defined in RFC 826.

          ATM --Asynchronous Transfer Mode. The international standard for cell relay in which multiple service types (such as voice, video, or data) are conveyed in fixed-length (53-byte) cells. Fixed-length cells allow cell processing to occur in hardware, thereby reducing transit delays. ATM is designed to take advantage of high-speed transmission media, such as E3, SONET, and T3.

          bundle --A logical grouping of one or more physical interfaces using the formats and procedures of multilink Frame Relay. A bundle emulates a physical interface to the Frame Relay data link layer. The bundle is also referred to as the MFR interface .

          Cisco Express Forwarding --Layer 3 IP switching technology that optimizes network performance and scalability for networks with large and dynamic traffic patterns.

          fast switching --Cisco feature in which a route cache expedites packet switching through a router.

          Inverse ARP --Inverse Address Resolution Protocol (ARP). Method of building dynamic routes in a network. Allows an access server to discover the network address of a device associated with a virtual circuit.

          MPLS --Multiprotocol Label Switching. Switching method that forwards IP traffic using a label. This label instructs the routers and the switches in the network where to forward the packets based on preestablished IP routing information.

          MQC --modular QoS command-line interface (CLI). A CLI structure that lets you create traffic polices and attach them to interfaces. A traffic policy contains a traffic class and one or more QoS features. A traffic class is used to classify traffic, and the QoS features in the traffic policy determine how to treat the classified traffic.

          PVC --permanent virtual circuit (or connection). Virtual circuit that is permanently established. PVCs save bandwidth associated with circuit establishment and teardown in situations where certain virtual circuits must exist all the time. In ATM terminology, this is called a permanent virtual connection.

          QoS --quality of service. Measure of performance for a transmission system that reflects its transmission quality and service availability.

          RBE --routed bridge encapsulation. Process by which a stub-bridged segment is terminated on a point-to-point routed interface. Specifically, the router is routing on an IEEE 802.3 or Ethernet header carried over a point-to-point protocol, such as PPP, RFC 1483 ATM, or RFC 1490 Frame Relay.

          SVC --switched virtual circuit. Virtual circuit that is dynamically established on demand and is torn down when transmission is complete. SVCs are used in situations where data transmission is sporadic. Called a switched virtual connection in ATM terminology.

          ToS --type of service byte. Second byte in the IP header that indicates the desired quality of service for a specific datagram.

          VC --virtual circuit. Logical circuit created to ensure reliable communication between two network devices. A VC is defined by a VPI/VCI pair and can be either permanent or switched.

          Routed Bridge Encapsulation with ATM Virtual Circuit Bundles

          Contents

          Routed Bridge Encapsulation with ATM Virtual Circuit Bundles

          The Routed Bridge Encapsulation with ATM Virtual Circuit Bundles feature enables routed bridge encapsulation (RBE) over ATM permanent virtual circuit (PVC) bundles. This feature supports PVC bundle member selection based on the quality of service (QoS) group or on the type of service (ToS) or Multiprotocol Label Switching (MPLS) Experimental (EXP) bit in each packet over RBE interfaces. The PVC bundles carry RBE traffic configured on ATM point-to-point subinterfaces.

          This feature also supports PVC bundle functionality for ATM adaptation layer 5 (AAL5) multiplexer (MUX) or Logical Link Control (LLC)/Subnetwork Access Protocol (SNAP) encapsulations and ATM PVC bundle scalability.

          Finding Feature Information

          Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.

          Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

          Restrictions for Routed Bridge Encapsulation with ATM Virtual Circuit Bundles

          The following restrictions apply to the Routed Bridge Encapsulation with ATM Virtual Circuit Bundles feature:

          • RBE over switched virtual circuit (SVC) bundles is not supported.

          • SVC bundle member selection based on QoS groups is not supported.

          • Fast switching is not supported (only Cisco Express Forwarding switching and process switching are supported).

          • PVC bundle member selection based on QoS groups does not support distributed platforms.

          • PVC bundle member selection based on QoS groups does not support bumping, protection, or PVC bundle incompleteness detection.

          PVC bundles are supported under the following conditions (numbers are maximum per interface and per router):

          • 1000 PVC bundles with AAL5 LLC/SNAP encapsulation, and each PVC bundle with four PVC bundle members

          • 800 PVC bundles with two members each and with AAL5 LLC/SNAP encapsulation, and interfaces with 4000 PVCs overall (including PVC bundle members)

          Information About Routed Bridge Encapsulation with ATM Virtual Circuit Bundles

          Benefits of Routed Bridge Encapsulation with ATM Virtual Circuit Bundles

          If the Routed Bridge Encapsulation with ATM Virtual Circuit Bundles feature is not configured, you can make the PVC bundle member selection based on ToS bit settings (for IP packets) or EXP bit settings (for MPLS packets). With the Routed Bridge Encapsulation with ATM Virtual Circuit Bundles feature configured, you can make the PVC bundle member selection based on the QoS group value associated with the packet on the ingress before route selection, or on the egress after selecting the adjacency. The packet’s pak_type header is marked with the QoS group to use, based on the generic match criterion provided by the modular QoS (MQC) command-line interface (CLI).

          The Routed Bridge Encapsulation with ATM Virtual Circuit Bundles feature gives you the flexibility to choose PVC bundle members based on various criteria. You can define any classification criterion for the traffic, mark the packets matching that criterion with the QoS group, and send them over a specific PVC bundle member to assign the appropriate quality of service to the corresponding class of traffic.

          Memory Impact of Routed Bridge Encapsulation with ATM Virtual Circuit Bundles

          The additional memory required for configuring the Routed Bridge Encapsulation with ATM Virtual Circuit Bundles feature does not exceed 50 bytes per PVC bundle.

          Performance Impact of Routed Bridge Encapsulation with ATM Virtual Circuit Bundles

          The Routed Bridge Encapsulation with ATM Virtual Circuit Bundles feature impacts forwarding path performance when PVC bundles are configured with QoS groups. This impact results because, during forwarding, QoS groups must be mapped to the appropriate PVC bundle member index in the array of adjacencies associated with the PVC bundle adjacency.

          This feature does not significantly increase CPU usage when traffic at line rates is sent over the PVC bundle (regardless of the selection criterion used for PVC bundle member selection).

          How to Configure Routed Bridge Encapsulation with ATM Virtual Circuit Bundles

          Specifying the Method for Selecting PVC Bundle Members

          Perform this task to specify the method of selection of PVC bundle members. You can specify one of two selection methods:

          • QoS group--Use the QoS group value associated with each packet for selection of PVC bundle members.

          • ToS or EXP--Use ToS bit settings of each packet (for IP packets) or EXP bit settings of each packet (for MPLS packets) for selection of PVC bundle members.

          The selection methods are mutually exclusive. This means that when the selection method based on QoS groups is specified on any PVC bundle member, no other selection method is allowed on the same PVC bundle. Similarly, if the selection method based on ToS or EXP is specified on any PVC bundle member, no other selection method is allowed on the same PVC bundle.


          Note
          • You can change the selection method from QoS groups to ToS or EXP only if no PVC bundle member has QoS groups or Inverse Address Resolution Protocol (InverseARP) configured.
          • You can change the selection method from ToS or EXP to QoS groups only if no PVC bundle member has precedence, protection, or bumping configured.
          SUMMARY STEPS

            1.    enable

            2.    configure terminal

            3.    interface atm slot / port

            4.    bundle bundle-name

            5.    selection-method {qos-group | tos-exp}

            6.    end


          DETAILED STEPS
             Command or ActionPurpose
            Step 1 enable


            Example:
            Router> enable
             

            Enables privileged EXEC mode.

            • Enter your password if prompted.

             
            Step 2 configure terminal


            Example:
            Router# configure terminal
             

            Enters global configuration mode.

             
            Step 3 interface atm slot / port


            Example:
            Router(config)# interface atm 2/0
             

            Specifies the ATM interface type and enters interface configuration mode. To determine the correct form of the interface atm command, see your ATM network module, port adapter, or router documentation.

             
            Step 4 bundle bundle-name


            Example:
            Router(config-if)# bundle bundle-test
             

            Creates a PVC bundle or modifies an existing PVC bundle and enters ATM bundle configuration mode.

             
            Step 5 selection-method {qos-group | tos-exp}


            Example:
            Router(config-if-atm-bundle)# selection-method qos-group
             

            Specifies the method for selection of PVC bundle members.

             
            Step 6 end


            Example:
            Router(config-if-atm-member)# end
             

            Ends the configuration session and returns to privileged EXEC mode.

             

            Configuring the QoS Group-Based Method for Selection of PVC Bundle Members

            Perform this task to configure the method for selection of PVC bundle members that is based on QoS groups.

            Before You Begin

            You must associate a QoS group or groups with a PVC bundle member. You can specify a QoS group, a range of QoS groups, or any combination of QoS groups and ranges of QoS groups.

            SUMMARY STEPS

              1.    enable

              2.    configure terminal

              3.    interface atm slot / port

              4.    bundle bundle-name

              5.    selection-method qos-group

              6.    pvc vpi / vci

              7.    qos-group qos-groups

              8.    end


            DETAILED STEPS
               Command or ActionPurpose
              Step 1 enable


              Example:
              Router> enable
               

              Enables privileged EXEC mode.

              • Enter your password if prompted.

               
              Step 2 configure terminal


              Example:
              Router# configure terminal
               

              Enters global configuration mode.

               
              Step 3 interface atm slot / port


              Example:
              Router(config)# interface atm 2/0
               

              Specifies the ATM interface type and enters interface configuration mode.

              • To determine the correct form of the interface atm command, see your ATM network module, port adapter, or router documentation.

               
              Step 4 bundle bundle-name


              Example:
              Router(config-subif)# bundle bundle-test
               

              Creates a PVC bundle or modifies an existing PVC bundle and enters ATM bundle configuration mode.

               
              Step 5 selection-method qos-group


              Example:
              Router(config-if-atm-bundle)# selection-method qos-group
               

              Specifies the method for selection of PVC bundle members based on QoS group.

               
              Step 6 pvc vpi / vci


              Example:
              Router(config-if-atm-bundle)# pvc 1/32
               

              Creates an ATM PVC and enters ATM bundle-member configuration mode.

               
              Step 7 qos-group qos-groups


              Example:
              Router(config-if-atm-member)# qos-group 1
               

              Associates a QoS group or groups with the PVC bundle member.

               
              Step 8 end


              Example:
              Router(config-if-atm-member)# end
               

              Ends the configuration session and returns to privileged EXEC mode.

               

              Configuring Explicit Inverse ARP PVC Selection for QoS Group-Based PVC Bundle Member Selection

              Perform this task to configure explicit Inverse ARP for a PVC bundle member.

              This procedure is optional and provides backward compatibility with existing PVC bundles, in which an Inverse ARP request is sent or expected to be received on the PVC bundle member with precedence 6. If a PVC bundle with selection based on QoS group is connected to an existing PVC bundle, you must follow this procedure to allow Inverse ARP to function. If you do not follow this procedure, Inverse ARP is sent over any of the available PVC bundle members.


              Note

              You can enable Inverse ARP for a PVC bundle member only when using the QoS groups method for selecting PVC bundle members.

              SUMMARY STEPS

                1.    enable

                2.    configure terminal

                3.    interface atm slot / port

                4.    bundle bundle-name

                5.    selection-method qos-group

                6.    pvc vpi / vci

                7.    qos-group qos-groups

                8.    inarp-vc

                9.    end


              DETAILED STEPS
                 Command or ActionPurpose
                Step 1 enable


                Example:
                Router> enable
                 

                Enables privileged EXEC mode.

                • Enter your password if prompted.

                 
                Step 2 configure terminal


                Example:
                Router# configure terminal
                 

                Enters global configuration mode.

                 
                Step 3 interface atm slot / port


                Example:
                Router(config)# interface atm 2/0
                 

                Specifies the ATM interface type and enters interface configuration mode.

                • To determine the correct form of the interface atm command, see your ATM network module, port adapter, or router documentation.

                 
                Step 4 bundle bundle-name


                Example:
                Router(config-if)# bundle bundle-test
                 

                Creates a bundle or modifies an existing bundle and enters ATM bundle configuration mode.

                 
                Step 5 selection-method qos-group


                Example:
                Router(config-if-atm-bundle)# selection-method qos-group
                 

                Specifies the method for selection of PVC bundle members based on QoS group.

                 
                Step 6 pvc vpi / vci


                Example:
                Router(config-if-atm-bundle)# pvc 1/32
                 

                Creates an ATM PVC and enters ATM bundle member configuration mode.

                 
                Step 7 qos-group qos-groups


                Example:
                Router(config-if-atm-member)# qos-group 1
                 

                Associates a QoS group or groups with the PVC bundle member.

                 
                Step 8 inarp-vc


                Example:
                Router(config-if-atm-member)# inarp-vc
                 

                Enables Inverse ARP for the PVC bundle member.

                 
                Step 9 end


                Example:
                Router(config-if-atm-member)# end
                 

                Ends the configuration session and returns to privileged EXEC mode.

                 

                Verifying Routed Bridge Encapsulation with ATM Virtual Circuit Bundles

                Perform this task to verify configuration of the Routed Bridge Encapsulation with ATM Virtual Circuit Bundles feature:

                SUMMARY STEPS

                  1.    enable

                  2.    show atm vc

                  3.    show interfaces

                  4.    show interfaces virtual-access


                DETAILED STEPS
                   Command or ActionPurpose
                  Step 1 enable


                  Example:
                  Router> enable
                   

                  Enters privileged EXEC mode.

                  • Enter your password if prompted.

                   
                  Step 2 show atm vc


                  Example:
                  Router# show atm vc
                   

                  Displays all ATM PVCs and SVCs and their traffic information.

                   
                  Step 3 show interfaces


                  Example:
                  Router# show interfaces
                   

                  Displays interleaving statistics.

                  • Interleaving data is displayed only if interleaving occurs.

                   
                  Step 4 show interfaces virtual-access


                  Example:
                  Router# show interfaces virtual-access
                   

                  Displays multilink bundle information.

                   

                  Configuration Examples for Routed Bridge Encapsulation with ATM Virtual Circuit Bundles

                  Specifying the Method for Selecting PVC Bundle Members Example

                  The following example shows how to specify the method for selecting PVC bundle members:

                  interface atm 2/0
 bundle cisco
  selection-method qos-group
  end

                  Configuring the QoS Group-Based Method for Selection of PVC Bundle Members Example

                  The following example shows how to configure the QoS group-based method for selection of PVC bundle members:

                  interface atm 2/0
 bundle cisco
  selection-method qos-group
  pvc 35/56
  qos-group 1
  end

                  Configuring Explicit Inverse ARP PVC Selection for QoS Group-Based PVC Bundle Member Selection Example

                  The following example shows how to configure explicit Inverse ARP PVC selection for QoS group-based PVC bundle member selection:

                  interface atm 2/0
 bundle cisco
  selection-method qos-group
  pvc 1/32
  qos-group 1
  inarp-vc
  end

                  Additional References

                  The following sections provide references related to the Routed Bridge Encapsulation with ATM Virtual Circuit Bundles feature.

                  Related Documents

                  Related Topic

                  Document Title

                  Broadband access aggregation concepts

                  Understanding Broadband Access Aggregation

                  Preparing for broadband access aggregation tasks

                  Preparing for Broadband Access Aggregation

                  Broadband access aggregation and DSL commands: complete command syntax, command mode, defaults, usage guidelines, and examples

                  Cisco IOS Broadband Access Aggregation and DSL Command Reference

                  Cisco IOS commands

                  Cisco IOS Master Commands List, All Releases

                  Standards

                  Standard

                  Title

                  None

                  --

                  MIBs

                  MIB

                  MIBs Link

                  None

                  To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at the following URL:

                  http:/​/​www.cisco.com/​go/​mibs

                  RFCs

                  RFC

                  Title

                  None

                  --

                  Technical Assistance

                  Description

                  Link

                  The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies.

                  To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds.

                  Access to most tools on the Cisco Support website requires a Cisco.com user ID and password.

                  http:/​/​www.cisco.com/​cisco/​web/​support/​index.html

                  Feature Information for Routed Bridge Encapsulation with ATM Virtual Circuit Bundles

                  The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

                  Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

                  Table 1 Feature Information for Routed Bridge Encapsulation with ATM Virtual Circuit Bundles

                  Feature Name

                  Releases

                  Feature Information

                  Routed Bridge Encapsulation with ATM Virtual Circuit Bundles

                  12.2(31)SB2 12.2(33)SRE 12.4(4)T

                  This feature enables RBE over ATM PVC bundles. This feature supports PVC bundle member selection based on the QoS group or on the ToS or MPLS EXP bit in each packet over RBE interfaces.

                  The following command was introduced:selection-method.

                  Glossary

                  ARP --Address Resolution Protocol. Internet protocol used to map an IP address to a MAC address. Defined in RFC 826.

                  ATM --Asynchronous Transfer Mode. The international standard for cell relay in which multiple service types (such as voice, video, or data) are conveyed in fixed-length (53-byte) cells. Fixed-length cells allow cell processing to occur in hardware, thereby reducing transit delays. ATM is designed to take advantage of high-speed transmission media, such as E3, SONET, and T3.

                  bundle --A logical grouping of one or more physical interfaces using the formats and procedures of multilink Frame Relay. A bundle emulates a physical interface to the Frame Relay data link layer. The bundle is also referred to as the MFR interface .

                  Cisco Express Forwarding --Layer 3 IP switching technology that optimizes network performance and scalability for networks with large and dynamic traffic patterns.

                  fast switching --Cisco feature in which a route cache expedites packet switching through a router.

                  Inverse ARP --Inverse Address Resolution Protocol (ARP). Method of building dynamic routes in a network. Allows an access server to discover the network address of a device associated with a virtual circuit.

                  MPLS --Multiprotocol Label Switching. Switching method that forwards IP traffic using a label. This label instructs the routers and the switches in the network where to forward the packets based on preestablished IP routing information.

                  MQC --modular QoS command-line interface (CLI). A CLI structure that lets you create traffic polices and attach them to interfaces. A traffic policy contains a traffic class and one or more QoS features. A traffic class is used to classify traffic, and the QoS features in the traffic policy determine how to treat the classified traffic.

                  PVC --permanent virtual circuit (or connection). Virtual circuit that is permanently established. PVCs save bandwidth associated with circuit establishment and teardown in situations where certain virtual circuits must exist all the time. In ATM terminology, this is called a permanent virtual connection.

                  QoS --quality of service. Measure of performance for a transmission system that reflects its transmission quality and service availability.

                  RBE --routed bridge encapsulation. Process by which a stub-bridged segment is terminated on a point-to-point routed interface. Specifically, the router is routing on an IEEE 802.3 or Ethernet header carried over a point-to-point protocol, such as PPP, RFC 1483 ATM, or RFC 1490 Frame Relay.

                  SVC --switched virtual circuit. Virtual circuit that is dynamically established on demand and is torn down when transmission is complete. SVCs are used in situations where data transmission is sporadic. Called a switched virtual connection in ATM terminology.

                  ToS --type of service byte. Second byte in the IP header that indicates the desired quality of service for a specific datagram.

                  VC --virtual circuit. Logical circuit created to ensure reliable communication between two network devices. A VC is defined by a VPI/VCI pair and can be either permanent or switched.