Configuring a Cisco Right-To-Use License

This guide provides an overview and guidance for configuring the Cisco® ASR 1000 Series Aggregation Services Routers with Right-To-Use License (RTU).

Feature Information for Cisco Right-To-Use License

The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.

Prerequisites for RTU

  • You must obtain the device certificate from the Cisco licensing infrastructure before you start the installation process.
  • You must have a Cisco user login account.

Information About Cisco RTU License

Overview of the Cisco Licensing Mechanism

The Cisco licensing mechanism provides flexibility to run a device at different technology package levels. This mechanism is referred to as technology package licensing and leverages the universal technology package based licensing solution. A universal image containing all levels of a software package is loaded on to the device. During startup, the device determines the highest level of license and loads the corresponding software features or subsystems.

The Cisco ASR 1001 Router and ASR 1002-X Router support technology package-based licenses that are not node locked. Technology packages and feature licenses are activated using evaluation licenses that are built in. Evaluation licenses are limited period-metered licenses that are valid for 60 days. When the time allowed for an evaluation license expires, the license is automatically upgraded to RTU license. After all the RTU licenses are activated, there is no expiration of license and are valid for a lifetime.

To enable an evaluation license, you have to accept the global end user license agreement (EULA).

RTU Supported Software Licenses
This section describes the various RTU-supported software licenses.

Note
Permanent licenses are not affected by Cisco IOS XE release upgrades.
An evaluation license is required to activate the licensed features. When a router enters the configuration mode, a check is performed to verify the license. Feature configurations are allowed only valid licenses are available. If a permanent license does not exist, Cisco IOS activates an RTU license when you accept the EULA agreement and the corresponding Cisco IOS functionalities will be available. The RTU license supports the following software features:

  • Inter chassis redundancy

  • Lawful intercept

  • Software redundancy

  • IPsec

  • Throughput

Accept the EULA to activate the corresponding feature. Migration of a permanent license from previous versions of the software images are seamless. For information on accepting the EULA, see Example: Accepting the Global EULA, page 10-6.

Evaluation licenses and RTU licenses available on the Cisco ASR 1000 Series Routers

Evaluation and RTU Licenses

Evaluation and RTU Licenses

License Name

License Description Evaluation License

FLS-ASR1001-5G

FLS-ASR1001-5G

Upgrade from 2.5G to 5G license for Cisco ASR1001 Router

Yes

FLSASR1-IOSRED

Software redundancy license for Cisco ASR1000 Series Aggregation Services Routers

Yes

Yes

FLSASR1-IPSEC IPSEC

License for Cisco ASR1000 Series Aggregation Services Routers

Yes

Yes

FLSASR1-FW FW

License for Cisco ASR1000 Series Aggregation Services Routers

Yes

Yes

FLSASR1-FPI

Flex. Pack. Insp License for Cisco ASR1000 Series Aggregation Services Routers

Yes

Yes

FLSASR1-FWNAT-R

Firewall and NAT Stateful Inter-Chassis Redundancy License

Yes

Yes

FLSASR1-LI

Lawful Intercept License for Cisco ASR1000 Series Aggregation Services Routers

Yes

Yes

FLSASR1-BB

Broadband License for Cisco ASR1000 Series Aggregation Services Routers

Yes

Yes

FLSASR1-BB-4K

Broadband 4K Sessions for Cisco ASR1000 Series Aggregation Services Routers

Yes

Yes

FLSASR1-BB-16K

Broadband 16K Sessions for Cisco ASR1000 Series Aggregation Services Routers

Yes

Yes

FLSASR1-BB-32K

Broadband 32K Sessions for Cisco ASR1000 Series Aggregation Services Routers

Yes

Yes

FLSASR1-CS-250P

CUBE(SP) 250Session License for Cisco ASR1000 Series Aggregation Services Routers Yes Yes

FLSASR1-CS-2KP

CUBE(SP) 2K Session License for Cisco ASR1000 Series Aggregation Services Routers Yes Yes

FLSASR1-CS-4KP

CUBE(SP) 4K Session License for Cisco ASR1000 Series Aggregation Services Routers Yes Yes

FLSASR1-CS-16KP

CUBE(SP) 16K Session License for Cisco ASR1000 Series Aggregation Services Routers Yes Yes

FLSASR1-CS-32KP

CUBE(SP) 32K Session License for Cisco ASR1000 Series Aggregation Services Routers Yes Yes

FLSASR1-CS-LAB

CUBE(SP) Lab Use Only Lic for Cisco ASR1000 Series Aggregation Services Routers Yes Yes

FLSASR1-CS-TPEX

CUBE(SP) License for ASR1000 in Video/B2BTP Ex Yes Yes

SLASR1-AIS

Cisco ASR 1000 Advanced IP Services License Yes Yes

SLASR1-AES

Cisco ASR 1000 Advanced Enterprise Services License Yes Yes

SLASR1-IPB

Cisco ASR 1000 IP BASE License
FLS-ASR1001-5G Throughput performance upgrade from 2.5G to 5G license for ASR1001 Yes Yes

How to Activate an Evaluation License


Note
Evaluation RTU licenses automatically changes to RTU licenses after an evaluation period of 60 days.
Evaluation licenses can be activated using the license boot level {adventerprise | advipservices |ipbase} command.

SUMMARY STEPS

  1. enable
  2. configure terminal
  3. license boot level {adventerprise | advipservices |ipbase}
  4. exit
  5. copy running-config startup-config
  6. reload

DETAILED STEPS

  Command or Action Purpose
Step 1

enable

Example:

Router> enable
Enables the privileged EXEC mode.

Enter your password if prompted.

Step 2

configure terminal

Example:

Router#configure terminal
Enters the global configuration mode.
Step 3

license boot level {adventerprise | advipservices |ipbase}

Example:

Router(config)#license boot level adventerprise

Enables the evaluation license.

Note 
Use the ? command with the technology-package command to see the software packages and features supported on your router.
Step 4

exit

Example:

Router(config)#exit
Exits the global configuration mode.
Step 5

copy running-config startup-config

Example:

Router#copy running-config startup-config
Saves the configuration.
Step 6

reload

Example:

Router#reload
Reloads the router. A reload is required to activate the software package.

Example

The following example shows how to activate an evaluation license: 

Router>enable
Router#configure terminal
Router(config)#license boot level adventerprise
% use 'write' command to make license boot config take effect on next boot
Router(config)#exit
Router#copy running-config startup-config
Router#reload

Configuring Throughput

For information on configuring throughput on the Cisco ASR 1001 Router, see Cisco ASR 1001 Router Quick Start Guide. For information on configuring throughput on the Cisco ASR 1002-X Router, see Cisco ASR 1001 Router Quick Start Guide.

Example: IPSec

Configure map or tunnels to the interface to trigger the EULA. Perform the following actions when required: 

step1:
Device#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Device(config)#crypto isakmp policy 1
Device(config-isakmp)#encryption aes
Device(config-isakmp)#hash md5
Device(config-isakmp)#group 2
Device(config-isakmp)#lifetime 86400
Device(config-isakmp)#authentication pre-share
Device(config-isakmp)#exit

step2:
Device(config)#crypto isakmp key cisco address 10.10.0.0

step3:
Device(config)#crypto ipsec transform-set trans esp-aes esp-md5-hmac
Device(cfg-crypto-trans)#mode transport
Device(cfg-crypto-trans)#exit

step4:
Device(config)#crypto map map1 10 ipsec-isakmp
% NOTE: This new crypto map will remain disabled until a peer
        and a valid access list have been configured.
Device(config-crypto-map)#set transform-set trans
Device(config-crypto-map)#set peer 10.10.0.0
Device(config-crypto-map)#match address 101
Device(config-crypto-map)#exit

step5:
Device(config)#access-list 101 permit ip 192.168.2.0 0.0.0.255 192.168.1.0 0.0.0.255
Device(config)#access-list 102 permit ip 100.100.100.0 0.0.0.255 100.100.100.0 0.0.0.255
Device(config)#exit

step6:
Device#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Device(config)#int GigabitEthernet0/0/1
Device(config-if)#crypto map map1
Device(config-if)#end

Example: Accepting an EULA for Software Redundancy License

The following example shows the acceptance of an EULA for the software redundancy feature: 

Router(config)#redundancy
Router(config-red)#mode
Router(config-red)#mode sso

PLEASE  READ THE  FOLLOWING TERMS  CAREFULLY. INSTALLING THE LICENSE OR LICENSE  KEY  PROVIDED FOR  ANY CISCO  PRODUCT  FEATURE  OR  USING SUCH PRODUCT  FEATURE  CONSTITUTES  YOUR  FULL ACCEPTANCE  OF  THE FOLLOWING TERMS. YOU MUST NOT PROCEED FURTHER IF YOU ARE NOT WILLING TO  BE BOUND BY ALL THE TERMS SET FORTH HEREIN.  

Use of this product feature requires  an additional license from Cisco, together with an additional  payment.  You may use this product feature on an evaluation basis, without payment to Cisco, for 60 days. Your use of the  product,  including  during the 60 day  evaluation  period,  is subject to the Cisco end user license agreement http://www.cisco.com/en/US/docs/general/warranty/English/EU1KEN_.html If you use the product feature beyond the 60 day evaluation period, you must submit the appropriate payment to Cisco for the license. After the 60 day  evaluation  period,  your  use of the  product  feature will be governed  solely by the Cisco  end user license agreement (link above), together  with any supplements  relating to such product  feature.  The above  applies  even if the evaluation  license  is  not  automatically terminated  and you do  not receive any notice of the expiration of the evaluation  period.  It is your  responsibility  to  determine when the evaluation  period is complete and you are required to make  payment to Cisco for your use of the product feature beyond the evaluation period.

Your  acceptance  of  this agreement  for the software  features on one product  shall be deemed  your  acceptance  with  respect  to all  such software  on all Cisco  products  you purchase  which includes the same software.  (The foregoing  notwithstanding, you must purchase a license for each software  feature you use past the 60 days evaluation  period, so  that  if you enable a software  feature on  1000  devices, you must purchase 1000 licenses for use past  the 60 day evaluation period.)    

Activation  of the  software command line interface will be evidence of your acceptance of this agreement.

ACCEPT? (yes/[no]): yes

Router(config)#

Example: Accepting an EULA for the Inter-Chassis Redundancy License

The following example shows the acceptance of an EULA for the application redundancy feature: 

Router(config-red)#application redundancy 

PLEASE  READ THE  FOLLOWING TERMS  CAREFULLY. INSTALLING THE LICENSE OR LICENSE  KEY  PROVIDED FOR  ANY CISCO  PRODUCT  FEATURE  OR  USING SUCH PRODUCT  FEATURE  CONSTITUTES  YOUR  FULL ACCEPTANCE  OF  THE FOLLOWING TERMS. YOU MUST NOT PROCEED FURTHER IF YOU ARE NOT WILLING TO  BE BOUND BY ALL THE TERMS SET FORTH HEREIN.  

Use of this product feature requires  an additional license from Cisco, together with an additional  payment.  You may use this product feature on an evaluation basis, without payment to Cisco, for 60 days. Your use of the  product,  including  during the 60 day  evaluation  period,  is subject to the Cisco end user license agreement http://www.cisco.com/en/US/docs/general/warranty/English/EU1KEN_.html If you use the product feature beyond the 60 day evaluation period, you must submit the appropriate payment to Cisco for the license. After the 60 day  evaluation  period,  your  use of the  product  feature will be governed  solely by the Cisco  end user license agreement (link above), together  with any supplements  relating to such product  feature.  The above  applies  even if the evaluation  license  is  not  automatically terminated  and you do  not receive any notice of the expiration of the evaluation  period.  It is your  responsibility  to  determine when the evaluation  period is complete and you are required to make  payment to Cisco for your use of the product feature beyond the evaluation period.

Your  acceptance  of  this agreement  for the software  features on one product  shall be deemed  your  acceptance  with  respect  to all  such software  on all Cisco  products  you purchase  which includes the same software.  (The foregoing  notwithstanding, you must purchase a license for each software  feature you use past the 60 days evaluation  period, so  that  if you enable a software  feature on  1000  devices, you must purchase 1000 licenses for use past  the 60 day evaluation period.)    

Activation  of the  software command line interface will be evidence of your acceptance of this agreement.
ACCEPT? (yes/[no]): yes

Example: IPSec

Configure map or tunnels to the interface to trigger the EULA. Perform the following actions when required: 

step1:
Device#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Device(config)#crypto isakmp policy 1
Device(config-isakmp)#encryption aes
Device(config-isakmp)#hash md5
Device(config-isakmp)#group 2
Device(config-isakmp)#lifetime 86400
Device(config-isakmp)#authentication pre-share
Device(config-isakmp)#exit

step2:
Device(config)#crypto isakmp key cisco address 10.10.0.0

step3:
Device(config)#crypto ipsec transform-set trans esp-aes esp-md5-hmac
Device(cfg-crypto-trans)#mode transport
Device(cfg-crypto-trans)#exit

step4:
Device(config)#crypto map map1 10 ipsec-isakmp
% NOTE: This new crypto map will remain disabled until a peer
        and a valid access list have been configured.
Device(config-crypto-map)#set transform-set trans
Device(config-crypto-map)#set peer 10.10.0.0
Device(config-crypto-map)#match address 101
Device(config-crypto-map)#exit

step5:
Device(config)#access-list 101 permit ip 192.168.2.0 0.0.0.255 192.168.1.0 0.0.0.255
Device(config)#access-list 102 permit ip 100.100.100.0 0.0.0.255 100.100.100.0 0.0.0.255
Device(config)#exit

step6:
Device#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Device(config)#int GigabitEthernet0/0/1
Device(config-if)#crypto map map1
Device(config-if)#end

Example: Accepting an EULA for the Lawful Intercept License

The following example shows the acceptance of an EULA for the lawful intercept feature. The following MIBs are required to activate lawful intercept license:

  • snmp-server view INTERCEPT_VIEW ciscoIpTapMIB

  • snmp-server view INTERCEPT_VIEW cisco802TapMIB

  • snmp-server view INTERCEPT_VIEW ciscoTap2MIB 

Router(config-red)#snmp-server view INTERCEPT_VIEW ciscoIpTapMIB included 

PLEASE  READ THE  FOLLOWING TERMS  CAREFULLY. INSTALLING THE LICENSE OR LICENSE  KEY  PROVIDED FOR  ANY CISCO  PRODUCT  FEATURE  OR  USING SUCH PRODUCT  FEATURE  CONSTITUTES  YOUR  FULL ACCEPTANCE  OF  THE FOLLOWING TERMS. YOU MUST NOT PROCEED FURTHER IF YOU ARE NOT WILLING TO  BE BOUND BY ALL THE TERMS SET FORTH HEREIN.  

Use of this product feature requires  an additional license from Cisco, together with an additional  payment.  You may use this product feature on an evaluation basis, without payment to Cisco, for 60 days. Your use of the  product,  including  during the 60 day  evaluation  period,  is subject to the Cisco end user license agreement http://www.cisco.com/en/US/docs/general/warranty/English/EU1KEN_.html If you use the product feature beyond the 60 day evaluation period, you must submit the appropriate payment to Cisco for the license. After the 60 day  evaluation  period,  your  use of the  product  feature will be governed  solely by the Cisco  end user license agreement (link above), together  with any supplements  relating to such product  feature.  The above  applies  even if the evaluation  license  is  not  automatically terminated  and you do  not receive any notice of the expiration of the evaluation  period.  It is your  responsibility  to  determine when the evaluation  period is complete and you are required to make  payment to Cisco for your use of the product feature beyond the evaluation period.

Your  acceptance  of  this agreement  for the software  features on one product  shall be deemed  your  acceptance  with  respect  to all  such software  on all Cisco  products  you purchase  which includes the same software.  (The foregoing  notwithstanding, you must purchase a license for each software  feature you use past the 60 days evaluation  period, so  that  if you enable a software  feature on  1000  devices, you must purchase 1000 licenses for use past  the 60 day evaluation period.)    

Activation  of the  software command line interface will be evidence of your acceptance of this agreement.
ACCEPT? (yes/[no]): yes

Sample Output for show Commands

Sample Output for the show license EULA Command 

Router#show license EULA
Feature name             EULA Accepted
------------             -------------
adventerprise            yes
advipservices            no
ipbase                   n/a
avc                      n/a
broadband                n/a
broadband_4k             n/a
cube_250                 n/a
cube_250_red             n/a
cube_ent_100             n/a
cube_ent_100_red         n/a
cube_lab                 n/a
cube_video_b2btp         n/a
cube_video_b2btp_red     n/a
firewall                 n/a
fpi                      n/a
fwnat_red                no
gtp_addon_aic            n/a
internal_service         n/a
ipsec                    no
lawful_intr              no
lisp                     n/a
nat64_stateful_2m        n/a
otv                      n/a
sgt_fw                   n/a
sw_redundancy            yes
throughput_10g           no
throughput_20g           no
throughput_36g           no
vpls                     n/a

PLEASE  READ THE  FOLLOWING TERMS  CAREFULLY. INSTALLING THE LICENSE OR
LICENSE  KEY  PROVIDED FOR  ANY CISCO  PRODUCT  FEATURE  OR  USING SUCH
PRODUCT  FEATURE  CONSTITUTES  YOUR  FULL ACCEPTANCE  OF  THE FOLLOWING
TERMS. YOU MUST NOT PROCEED FURTHER IF YOU ARE NOT WILLING TO  BE BOUND
BY ALL THE TERMS SET FORTH HEREIN.

Use of this product feature requires  an additional license from Cisco,
together with an additional  payment.  You may use this product feature
on an evaluation basis, without payment to Cisco, for 60 days. Your use
of the  product,  including  during the 60 day  evaluation  period,  is
subject to the Cisco end user license agreement
http://www.cisco.com/en/US/docs/general/warranty/English/EU1KEN_.html
If you use the product feature beyond the 60 day evaluation period, you
must submit the appropriate payment to Cisco for the license. After the
60 day  evaluation  period,  your  use of the  product  feature will be
governed  solely by the Cisco  end user license agreement (link above),
together  with any supplements  relating to such product  feature.  The
above  applies  even if the evaluation  license  is  not  automatically
terminated  and you do  not receive any notice of the expiration of the
evaluation  period.  It is your  responsibility  to  determine when the
evaluation  period is complete and you are required to make  payment to
Cisco for your use of the product feature beyond the evaluation period.

Your  acceptance  of  this agreement  for the software  features on one
product  shall be deemed  your  acceptance  with  respect  to all  such
software  on all Cisco  products  you purchase  which includes the same
software.  (The foregoing  notwithstanding, you must purchase a license
for each software  feature you use past the 60 days evaluation  period,
so  that  if you enable a software  feature on  1000  devices, you must
purchase 1000 licenses for use past  the 60 day evaluation period.)

Activation  of the  software command line interface will be evidence of
your acceptance of this agreement.

Sample Output for the show license all Command 

Router#show license all
License Store: Primary License Storage
License Store: Built-In License Storage
StoreIndex: 0   Feature: adventerprise                     Version: 1.0
        License Type: EvalRightToUse
        License State: Active, In Use
            Evaluation total period: 8  weeks 4  days
            Evaluation period left: 6  weeks 2  days
            Period used: 2  weeks 1  day
            Transition date: Aug 24 2012 05:14:39
        License Count: Non-Counted
        License Priority: Low
StoreIndex: 1   Feature: advipservices                     Version: 1.0
        License Type: EvalRightToUse
        License State: Active, Not in Use, EULA not accepted
            Evaluation total period: 8  weeks 4  days
            Evaluation period left: 8  weeks 4  days
            Period used: 0  minute  0  second
        License Count: Non-Counted
        License Priority: None
StoreIndex: 2   Feature: fwnat_red                         Version: 1.0
        License Type: EvalRightToUse
        License State: Active, Not in Use, EULA not accepted
            Evaluation total period: 8  weeks 4  days
            Evaluation period left: 8  weeks 4  days
            Period used: 0  minute  0  second
        License Count: Non-Counted
        License Priority: None
StoreIndex: 3   Feature: ipsec                             Version: 1.0
        License Type: EvalRightToUse
        License State: Active, Not in Use, EULA not accepted
            Evaluation total period: 8  weeks 4  days
            Evaluation period left: 8  weeks 4  days
            Period used: 0  minute  0  second
        License Count: Non-Counted
        License Priority: None
StoreIndex: 4   Feature: lawful_intr                       Version: 1.0
        License Type: EvalRightToUse
        License State: Active, Not in Use, EULA not accepted
            Evaluation total period: 8  weeks 4  days
            Evaluation period left: 8  weeks 4  days
            Period used: 0  minute  0  second
        License Count: Non-Counted
        License Priority: None
StoreIndex: 5   Feature: sw_redundancy                     Version: 1.0
        License Type: RightToUse
        License State: Active, In Use
        License Count: Non-Counted
        License Priority: Low
StoreIndex: 6   Feature: throughput_10g                    Version: 1.0
        License Type: EvalRightToUse
        License State: Active, Not in Use, EULA not accepted
            Evaluation total period: 8  weeks 4  days
            Evaluation period left: 8  weeks 4  days
            Period used: 0  minute  0  second
        License Count: Non-Counted
        License Priority: None
StoreIndex: 7   Feature: throughput_20g                    Version: 1.0
        License Type: EvalRightToUse
        License State: Active, Not in Use, EULA not accepted
            Evaluation total period: 8  weeks 4  days
            Evaluation period left: 8  weeks 4  days
            Period used: 0  minute  0  second
        License Count: Non-Counted
        License Priority: None
StoreIndex: 8   Feature: throughput_36g                    Version: 1.0
        License Type: EvalRightToUse
        License State: Active, Not in Use, EULA not accepted
            Evaluation total period: 8  weeks 4  days
            Evaluation period left: 8  weeks 4  days
            Period used: 0  minute  0  second
        License Count: Non-Counted
        License Priority: None

Cisco ONE Suites

Cisco ONE Suites is a new way for customers to purchase infrastructure software. Cisco ONE offers a simplified purchasing model, centered on common customer scenarios in the data center, wide area network, and local access networks.

Smart Licensing supports Smart License Cisco ONE suite level licenses and image licenses, such as ipbase, Advanced IP Services (AIS), Advanced Enterprise Services (AES) and feature license and throughput performance, crypto throughput and port licensing on ASR 1000 Aggregation Series Routers.

To know more about Cisco One Suites, please refer to Cisco ONE Suites.

How to Activate Cisco One Suite License

SUMMARY STEPS

  1. enable
  2. configure terminal
  3. license boot suite suite-name
  4. exit
  5. reload

DETAILED STEPS

  Command or Action Purpose
Step 1

enable

Example:

Router> enable
Enables the privileged EXEC mode.

Enter your password if prompted.

Step 2

configure terminal

Example:

Router#configure terminal
Enters the global configuration mode.
Step 3

license boot suite suite-name

Example:

Router(config)# license boot suite FoundationSuiteK9

Enables the suite license.

Note 
This command is required for activating both the evaluation and permanent licenses.
Step 4

exit

Example:

Router(config)#exit
Exits the global configuration mode.
Step 5

reload

Example:

Router# reload
Reloads the router. A reload is required to activate the software suite.

Example

The following example shows how to activate an suite license: 

Router>enable
Router#configure terminal
Router(config)#license boot suite FoundationSuiteK9
 
PLEASE READ THE FOLLOWING TERMS CAREFULLY. INSTALLING THE LICENSE OR
LICENSE KEY PROVIDED FOR ANY CISCO PRODUCT FEATURE OR USING SUCH
PRODUCT FEATURE CONSTITUTES YOUR FULL ACCEPTANCE OF THE FOLLOWING
TERMS. YOU MUST NOT PROCEED FURTHER IF YOU ARE NOT WILLING TO BE BOUND
BY ALL THE TERMS SET FORTH HEREIN.
 
Use of this product feature requires an additional license from Cisco,
together with an additional payment. You may use this product feature
on an evaluation basis, without payment to Cisco, for 60 days. Your use
of the product, including during the 60 day evaluation period, is
subject to the Cisco end user license agreement
http://www.cisco.com/en/US/docs/general/warranty/English/EU1KEN_.html
If you use the product feature beyond the 60 day evaluation period, you
must submit the appropriate payment to Cisco for the license. After the
60 day evaluation period, your use of the product feature will be
governed solely by the Cisco end user license agreement (link above),
together with any supplements relating to such product feature. The
above applies even if the evaluation license is not automatically
terminated and you do not receive any notice of the expiration of the
evaluation period. It is your responsibility to determine when the
evaluation period is complete and you are required to make payment to
Cisco for your use of the product feature beyond the evaluation period.
 
Your acceptance of this agreement for the software features on one
product shall be deemed your acceptance with respect to all such
software on all Cisco products you purchase which includes the same
software. (The foregoing notwithstanding, you must purchase a license
for each software feature you use past the 60 days evaluation period,
so that if you enable a software feature on 1000 devices, you must
purchase 1000 licenses for use past the 60 day evaluation period.)
 
Activation of the software command line interface will be evidence of
your acceptance of this agreement.
 
 
ACCEPT? [yes/no]: yes
% use 'write' command to make license boot config take effect on next boot
 
Router(config)#
*Nov 6 01:48:34.023: %LICENSE-6-EULA_ACCEPTED: EULA for feature FoundationSuiteK9 1.0 has been accepted. UDI=C3900-SPE100/K9:FOC14440KXB; StoreIndex=3:Built-In License Storage
Router(config)#exit
Router#write
Router#reload

Additional References

The following sections provide references related to the Call Home feature.

Related Documents

Related Topic

Title

Cisco IOS XE commands

Cisco IOS Master Commands List, All Releases

Explains how the Smart Call Home service offers web-based access to important information on select Cisco devices and offers higher network availability, and increased operational efficiency by providing

real-time alerts.

Smart Call Home User Guide

Smart Call Home site page on Cisco.com for access to all related product information.

Cisco Smart Call Home site

Public Key Infrastructure (PKI) and Certificate Authority configuration in Cisco IOS XE software

Cisco IOS XE Security Configuration Guide: Secure Connectivity

Standards

Standard

Title

No new or modified standards are supported by this feature, and support for existing standards has not been modified by this feature.

—

MIBs

MIB

MIBs Link

CISCO-CALLHOME-MIB

To locate and download MIBs for selected platforms, Cisco IOS XE software releases, and feature sets, use Cisco MIB Locator found at the following URL:

http://www.cisco.com/go/mibs

RFCs

RFC

Title

No new or modified RFCs are supported by this feature, and support for existing RFCs has not been modified by this feature.

—

Technical Assistance

Description

Link

The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies.

To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds.

Access to most tools on the Cisco Support website requires a Cisco.com user ID and password.

http://www.cisco.com/cisco/web/support/index.html

Feature Information for Call Home

Use Cisco Feature Navigator to find information about platform support and software image support. Cisco Feature Navigator enables you to determine which Cisco IOS XE software images support a specific software release, feature set, or platform. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn . An account on Cisco.com is not required.


Note
The Feature Information table below lists only the Cisco IOS XE software release that introduced support for a given feature in a given Cisco IOS XE software release train. Unless noted otherwise, subsequent releases of that Cisco IOS XE software release train also support that feature.
Table 1. Feature Information for Call Home

Feature Name

Releases

Feature Information

Call Home

Cisco IOS XE Release 3.13S

The Call Home feature provides e-mail-based and web-based notification of critical system events. A versatile range of message formats are available for optimal compatibility with pager services, standard e-mail, or XML-based automated parsing applications.

The following commands were introduced or modified:

show diagnostic commands