|
Command or Action |
Purpose |
|
enable
Example:
Router> enable
|
Enables privileged EXEC mode. Enter your password when prompted. |
|
configure terminal
Example:
Router# configure terminal
|
Enters global configuration mode. |
|
network-clock-participate slot number
Example:
Router(config)# network-clock-participate slot 1
|
Enables the network module in the specified slot to use the network clock for its timing. |
|
network-clock-participate slot number
Example:
Router(config)# network-clock-participate slot 4
|
Enables the network module in the specified slot to use the network clock for its timing. |
|
network-clock-participate aim number
Example:
Router(config)# network-clock-participate aim 0
|
Specifies that the AIM in Slot 0 will derive clocking from the network source. |
|
voice service {pots | voatm | vofr | voip}
Example:
Router(config)# voice service voatm
|
Enters voice service configuration mode and specifies VoATM as the encapsulation type. |
|
session protocol aal2
Example:
Router(config-voi-serv)# session protocol aal2
|
Enters voice-service-session configuration mode and specifies ATM adaptation layer 2 (AAL2) trunking. |
|
subcell-mux
Example:
Router(conf-voi-serv-sess)# subcell-mux
|
Enables AAL2 common part sublayer (CPS) subcell multiplexing. |
|
codec aal2-profile custom profile-number codec
Example:
Router# codec aal2-profile custom 51 0 0 llcc 40 0 15
|
Sets the codec profile for the DSP on a per-call basis and specifies the lossless compression codec. |
|
controller t1 | e1 slot/port
Example:
Router(config)# controller e1 1/0
|
Enters controller configuration mode for the selected T1 or E1. |
|
mode atm aim aim-slot
Example:
Router(config-controller)# mode atm aim 0
|
Sets the mode of the T1 or E1 controller in AIM Slot 0. |
|
controller t1 | e1 slot/port
Example:
Router(config)# controller e1 4/0
|
Enters controller configuration mode for the selected T1 or E1. |
|
ds0-group ds0-group-number timeslots timeslot-list type signaling method
Example:
Router(config-controller)# ds0-group 0 timeslots 1 type ext-sig
|
Specifies the DS0 time slots that make up a logical voice port on a T1 or E1 controller and specifies the signaling type used by the router. |
|
interface atm interface-number /subinterface-number
Example:
Router(config) # interface atm 1/0
|
Enters configuration mode for the selected ATM interface. |
|
pvc vpi /vci
Example:
Router(config-if-atm)# pvc 10/110
|
Enters configuration mode for the selected PVC. |
|
vbr-rt peak-rate average-rate burst
Example:
Router(config-if-atm-pvc)# vbr-rt 1920 1920 255
|
Configures real-time variable bit rate (VBR) for VoATM voice connections. |
|
encapsulation aal2
Example:
Router(config-if-atm-pvc)# encapsulation aal2
|
Configures the encapsulation type for the ATM virtual circuit. |
|
dial-peer voice tag voatm
Example:
Router(config)# dial-peer voice 1001 voatm
|
Defines a dial-peer and specifies the method of voice encapsulation as VoATM. |
|
destination-pattern string
Example:
Router(config-dial-peer)# destination-pattern 1001
|
Specifies the prefix to be used by the dial peer. |
|
session protocol aal2-trunk
Example:
Router(config-dial-peer)# session protocol aal2-trunk
|
Specifies the dial peer uses AAL2 nonswitched trunk session protocol. |
|
session target interface pvc vpi/vci
Example:
Router(config-dial-peer)# session target atm 1/0 pvc 10/100 9
|
Specifies the network-specific address for the VoATM dial peer. |
|
signal-type cas | cept | ext-signal | transparent
Example:
Router(config-dial-peer)# signal-type ext-signal
|
Specifies that external signaling is used when connecting to the dial peer. The DSP does not generate any signaling frames. |
|
codec aal2-profile custom profile-number codec
Example:
Router(config-dial-peer)# codec aal2-profile custom 51 llcc
|
Sets the codec profile for the DSP on a per-call basis and specifies the lossless compression codec. |
|
voice-port {slot-number/subunit-number/port | slot/port:ds0-group-no}
Example:
Router(config)# voice-port 2/0:0
|
Enters voice-port configuration mode. |
|
playout-delay {fax | maximum | nominal} milliseconds
Example:
Router(config-voice-port)# playout-delay nominal 25
|
Tunes the playout buffer to accommodate packet jitter caused by switches in the WAN. The nominal keyword specifies the initial (and minimum allowed) delay time that the DSP inserts before playing out voice packets, in milliseconds. |
|
connection {plar | tie-line | plar-opx} digits | {trunk digits [answer-mode]}
Example:
Router(config-voice-port)# connection trunk 1001
|
Associates this voice-port to destination-pattern 1001. |