IP Multicast: MVPN Configuration Guide, Cisco IOS XE Amsterdam 17.1.x
Bias-Free Language
The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
The Multicast VPN Inter-AS Support feature enables Multicast Distribution Trees (MDTs) used for Multicast VPNs (MVPNs) to
span multiple autonomous systems. Benefits include increased multicast coverage to customers that require multicast to span
multiple service providers in a Multiprotocol Label Switching (MPLS) Layer 3 Virtual Private Network (VPN) service with the
flexibility to support all options described in RFC 4364. Additionally, the Multicast VPN Inter-AS Support feature can be
used to consolidate an existing MVPN service with another MVPN service, such as the case with a company merger or acquisition.
Finding Feature Information
Your software release may not support all the features documented in this module. For the latest caveats and feature information,
see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module,
and to see a list of the releases in which each feature is supported, see the feature information table.
Use Cisco Feature Navigator to find information about platform support and Cisco software image
support. To access Cisco Feature Navigator, go to https://cfnng.cisco.com/. An account on Cisco.com is not required.
Prerequisites for Configuring Multicast VPN Inter-AS Support
You understand IP multicast concepts and configuration tasks.
You understand MVPN concepts and configuration tasks.
You understand Border Gateway Protocol (BGP) concepts and configuration tasks.
You understand MPLS Layer 3 VPN concepts and configuration tasks.
Restrictions for Configuring Multicast VPN Inter-AS Support
The Multicast VPN Inter-AS Support feature requires that all routers in the core be configured for Protocol Independent Multicast
(PIM) Source Specific Multicast (SSM). Protocol Independent Multicast sparse mode (PIM-SM) and bidirectional PIM (bidir-PIM)
are not supported.
Information About Multicast VPN Inter-AS Support
MVPN Inter-AS Support Overview
As a general concept, MVPN inter-AS support enables service providers to provide multicast connectivity to VPN sites that
span multiple autonomous systems. There are two types of MVPN inter-AS deployment scenarios:
Single provider inter-AS--A service provider whose internal network consists of multiple autonomous systems.
Intraprovider inter-AS--Multiple service providers that need to coordinate their networks to provide inter-AS support.
The extensions added to support the Multicast VPN Inter-AS Support feature enable MDTs used for MVPNs to span multiple autonomous
systems.
Benefits of MVPN Inter-AS Support
The MVPN Inter-AS Support feature provides the following benefits to service providers:
Increased multicast coverage to customers that require multicast to span multiple services providers in an MPLS Layer 3 VPN
service with the flexibility to support all options described in RFC 4364.
The ability to consolidate an existing MVPN service with another MVPN service, such as the case with a company merger or acquisition.
MVPN Inter-AS Support Implementation Requirements
The Multicast VPN Inter-AS Support feature was implemented in the software in accordance to the following requirements:
To achieve parity with unicast inter-AS support, the software must support the following inter-AS options for MVPN (as defined
in RFC 4364):
Option A--Back-to-back VPN routing and forwarding (VRF) instances at the Autonomous System Border Router (ASBR) provider edge
(PE) routers
The Option A model assumes direct connectivity between PE routers of different autonomous systems. The PE routers are attached
by multiple physical or logical interfaces, each of which is associated with a given VPN (through a VRF instance). Each PE
router, therefore, treats the adjacent PE router like a customer edge (CE) router, and the standard Layer 3 MPLS VPN mechanisms
are used for route redistribution with each autonomous system; that is, the PEs use exterior BGP (eBGP) to distribute unlabeled
IPv4 addresses to each other.
Note
Option A allows service providers to isolate each autonomous system from the other, which provides better control over routing
exchanges and security between the two networks. Option A, however, is considered the least scalable of all the inter-AS connectivity
options.
Option B--VPNv4 route exchange between ASBRs
In the Option B model, the PE routers use interior BGP (iBGP) to redistribute labeled VPNv4 routes either to an ASBR or to
a route reflector of which an ASBR is a client. ASBRs then use multiprotocol eBGP (MP-eBGP) to advertise VPNv4 routes into
the local autonomous system.
MP-eBGP provides the functionality to advertise VPNv4 prefix and label information across the service provider boundaries.
The advertising ASBR router replaces the two-level label stack (which it uses to reach the originating PE router and VPN destination
in the local autonomous system) with a locally allocated label before advertising the VPNv4 route. This replacement is necessary
because the next-hop attribute of all routes advertised between the two service providers is reset to the ASBR router’s peering
address, so the ASBR router becomes the termination point of the label-switched path (LSP) for the advertised routes. To preserve
the LSP between ingress and egress PE routers, the ASBR router must allocate a local label that may be used to identify the
label stack of the route within the local VPN network. This newly allocated label is set on packets sent toward the prefix
from the adjacent service provider.
Note
Option B enables service providers to isolate both autonomous systems with the added advantage that it scales to a higher
degree than Option A.
Option C--Exchange of VPNv4 routes between route reflectors (RRs) using multihop eBGP peering sessions
The Option C model combines MP-eBGP exchange of VPNv4 routes between RRs of different autonomous systems with the next hops
for these routes exchanged between corresponding ASBR routers. In the Option C model, VPNv4 routes are neither maintained
nor distributed by the ASBRs. ASBRs must maintain labeled IPv4 /32 routes to the PE routers within its autonomous system and
use eBGP to distribute these routes to other autonomous systems. ASBRs in any transit autonomous systems will also have to
use eBGP to pass along the labeled /32 routes. The result is the creation of a LSP from the ingress PE router to the egress
PE router.
Because RRs of different autonomous systems will not be directly connected, multihop functionality is required to allow for
the establishment of the MP-eBGP peering sessions. The exchange of next hops is necessary because the RRs do not reset the
next-hop attribute of the VPNv4 routes when advertising them to adjacent autonomous systems because they do not want to attract
the traffic for the destinations that they advertise. They are not the original endpoint--just a relay station between the
source and receiver PEs. The PE router next-hop addresses for the VPNv4 routes, thus, are exchanged between ASBR routers.
The exchange of these addresses between autonomous systems can be accomplished by redistributing the PE router /32 addresses
between the autonomous systems or by using BGP label distribution.
Note
Option C normally is deployed only when each autonomous system belongs to the same overall authority, such as a global Layer
3 MPLS VPN service provider with autonomous systems in different regions of the world. Option B is equally suited for this
purpose and is also deployed in networks where autonomy between different regions is desired.
The Cisco software must support inter-AS MDTs. An inter-AS MDT is an MDT that extends across autonomous system boundaries.
In the context of MVPN, because MVPN packets are encapsulated when being forwarded between ASBRs, an inter-AS MDT is needed
(for Option B and Option C) to extend the MDT across the boundaries of the autonomous system.
Limitations That Prevented Option B and Option C Support
Prior to the extensions introduced in association with the Multicast VPN Inter-AS Support feature, limitations existed that
prevented MVPN inter-AS support for Option B and Option C. These limitations were related to the following areas:
Supporting reverse path forwarding (RPF) for inter-AS sources (applicable mainly to Option B)
When a PE router sends a PIM join (source PE address, MDT group address) for the default MDT, each P router in the path between
the source and the destination PE routers must perform an RPF check on the source. Because Interior Gateway Protocol (IGP)
routes (which would include the routes to source PE routers in remote autonomous systems) are not leaked across autonomous
systems, the P routers in the receiving autonomous system were unable to perform an RPF check.
When a PIM join is received in an MVPN, an IP lookup is performed in the VRF to find the next hop toward the destination.
This destination must be a PIM neighbor that can be reached through the MDT tunnel interface. However, because ASBRs change
the next hop of the originating PE router for a given MDT group, the originating source address would be lost, and the RPF
check at the PE router would fail.
Note
In typical Option C inter-AS deployments, the limitation related to supporting RPF for MVPN inter-AS support was not applicable
because the RRs store all VPNv4 routes.
Supporting an inter-AS MDT (applicable to Option B and Option C)
The default MDT relies on the ability of the PE routers to join the default multicast group. The source of the group is the
originating PE router address used for MP-BGP peering. Prior to the extensions introduced in association with the Multicast
VPN Inter-AS Support feature, this address could not be reached between autonomous systems because IGP routes could not be
distributed across the autonomous systems. The default MDT for inter-AS MVPN, thus, could not be established.
MVPN Inter-AS Support for Option A
The limitations that prevented support for MVPN inter-AS support Options B and C have never applied to Option A for the following
reasons:
For Option A, native IP forwarding is used by the PE routers between autonomous systems; therefore, Option A does not require
support for inter-AS MDTs.
For Option A, the MDT is limited to one autonomous system; therefore, the issues associated with managing MDT group addresses
between autonomous systems and RPF for inter-AS sources never applied to Option A.
Note
Because Option A requires that one physical or logical interface be configured for each VRF, Option A is considered the least
scalable MVPN inter-AS solution.
MVPN Inter-AS Support Solution for Options B and C
The following extensions introduced in association with the MVPN Inter-AS Support feature resolve the MVPN inter-AS protocol
limitations related to supporting RPF and inter-AS MDTs in Option B and C deployments:
BGP connector attribute in MP-BGP--This attribute helps preserve the identity of a PE router originating a VPNv4 prefix.
This BGP extension helps solve the challenge of supporting RPF to sources in a remote autonomous system.
BGP MDT Subaddress Family Identifier (SAFI)--This identifier helps ASBRs RPF to source PEs in a remote autonomous systems.
The BGP MDT SAFI also helps ASBRs and receiver PEs insert the RPF Vector needed to build an inter-AS MDT to source PEs in
remote autonomous systems.
BGP Connector Attribute
In an adjacent autonomous system, a PE router that wants to join a particular source of the default MDT for a given MVPN
must know the originator’s address of the source PE router. This presents some challenges for Option B inter-AS deployments
because the originator next hop for VPNv4 routes is rewritten at one or more points in the network. To solve this limitation,
each VPNv4 route must carry a new attribute (the BGP connector attribute) that defines the route’s originator.
The BGP connector attribute is a transitive attribute that stores the PE router that originated a VPNv4 prefix. In a local
autonomous system, the BGP connector attribute is the same as the next hop attribute. When advertised to other ASBRs in VPNv4
advertisements (as is the case in Option B), the value of the BGP connector attribute is preserved even after the next hop
attribute is rewritten by ASBRs. The BGP connector attribute is a critical component of the MVPN inter-AS solution, helping
to enable RPF to sources in remote autonomous systems.
Note
The BGP connector attribute also helps ASBRs and receiver PEs insert the RPF Vector needed to build the inter-AS MDT for
source PEs in remote autonomous systems. For more information about RPF Vectors, see the
PIM RPF Vector section.
The format of the BGP connector attribute is shown in the figure.
Figure 1. BGP Connector Attribute
BGP MDT SAFI Updates for MVPN Inter-AS Support
The BGP MDT SAFI is specifically designed to carry the address of the source PE router to which a PIM join should be sent
for the MDT group contained in the PIM join. The format of the Network Layer Reachability Information (NLRI) carried in this
SAFI is {RD:PE-IP-address}. The BGP MDT SAFI is capable of being advertised across autonomous system boundaries. Each MDT
group is carried in the MP_REACH attribute using the format shown in the figure.
Figure 2. MDT SAFI Format
When RRs and MP-eBGP peerings are used, the advertisement of the BGP MDT SAFI is independent of the advertisement of VPNv4
routes. BGP MDT SAFI advertisements, however, are processed and filtered like VPNv4 advertisements.
ASBRs store the path advertised in BGP MDT SAFI updates in a separate table. How the BGP MDT SAFI is advertised determines
the RPF path to the PE router that originated the advertisement.
PEs also store the BGP MDT SAFI update in a separate table. PE routers use the information contained in the BGP MDT SAFI
to determine the ASBR that is the exit router to the source PE router in an adjacent autonomous system.
PIM RPF Vector
Normally, in an MVPN environment, PIM sends join messages containing the IP address of upstream PE routers that are sources
of a given MDT group. To be able to perform RPF checks, however, P routers must have IPv4 reachability to source PE routers
in remote autonomous systems. This behavior is not the case with inter-AS Options B and C because the autonomous systems do
not exchange any of their IGP routes, including those of their local PE routers. However, P routers do have reachability to
the BGP next hop of the BGP MDT update received with the BGP MDT SAFI updates at the PE routers. Therefore, if the PE routers
add the remote PE router IP address (as received within the BGP MDT SAFI) and the BGP next-hop address of this address within
the PIM join, the P routers can perform an RPF check on the BGP next-hop address rather than the original PE router address,
which, in turn, allows the P router to forward the join toward the ASBR that injected the MDT SAFI updates for a remote autonomous
system. This functionality is generally referred to as the
PIM RPF Vector ; the actual vector that is inserted into PIM joins is referred to as the
RPF Vector
or the
Proxy Vector . The PIM RPF Vector, therefore, enables P routers to determine the exit ASBR to a source PE router in a remote autonomous
system. Having received the join that contains a RPF Vector, an ASBR can then determine that the next-hop address is in fact
itself and can perform an RPF check based on the originating PE router address carried in the PIM join.
When configured on PE routers using the
ipmulticastrpfproxyvector command, the RPF Vector is encoded as a part of the source address in PIM join and prune messages. The RPF Vector is the
IGP next hop for PIM RPF neighbor in PIM join and prune messages, which is typically the exit ASBR router to a prefix in a
remote autonomous system.
The format of this PIM RPF Vector encoding in PIM join and prune messages is shown in the figure.
Figure 3. PIM RPF Vector Encoded in PIM Join and Prune Messages
Note
RPF Vectors can be used natively in an IP environment (that is, in a non-VPN environment). For more information about the
use of RPF Vectors in a native environment, see RFC 5496,
The Reverse Path Forwarding (RPF) Vector TLV .
Originators of an RPF Vector
Whether or not a PE router originates an RPF Vector is determined by configuration; that is, the ipmulticastrpfproxyvector command must be configured on all PE routers in order for an RPF Vector to be originated. The PE router that originates an
RPF Vector always performs an RPF lookup on the source. When a PE router performs an RPF lookup on a source, the PE router
learns the origin of an RPF Vector in one of the following ways:
In an MVPN network environment, the RPF Vector is learned from BGP MDT SAFI updates.
In a native IP network environment, the RPF Vector is learned from either IP unicast routing (AFI=1, SAFI=1) or IP multicast
reverse-path information (AFI=1, SAFI=2).
Routers that understand the RPF Vector format advertise the RPF Vector in PIM hello messages.
Recipients of an RPF Vector
When a router receives a PIM join that contains an RPF Vector, that router stores the RPF Vector so that it can generate a
PIM join to the exit ASBR router. P routers, thus, learn the RPF Vector from PIM joins. The RPF Vector is advertised to all
P routers in the core. If multiple RPF Vectors are received by a router, the RPF Vector with the lower originator address
is used. When the RPF Vector is present, it takes priority; as a result, RPF checks are triggered periodically to readvertise
RPF Vectors upstream. If a router receives an RPF Vector that references a local interface (typically an ASBR), the RPF Vector
is discarded and a normal RPF lookup is performed.
ASBR Receipt of an RPF Vector
When an ASBR receives an RPF Vector, it typically references a local interface (most likely a loopback interface); in which
case, the RPF Vector is discarded and a normal RPF lookup is performed. If the RD type is 2, the ASBR performs an RPF lookup
in the BGP MDT table that is built from the BGP MDT SAFI updates; this type of RPF lookup uses both the RD and the source
PE address contained in the PIM join.
Interoperability with RPF Vector
A new PIM hello option is introduced along with the PIM RPF Vector extension to determine if the upstream router is capable
of parsing the new encoding. An RPF Vector is included in PIM messages only when all PIM neighbors on an RPF interface support
it.
MDT Address Family in BGP for Multicast VPN Inter-AS Support
The mdt keyword has been added to the address-familyipv4 command to configure an MDT address-family session.
Supported Policy
The following policy configuration parameters are supported under the BGP MDT SAFI:
Mandatory attributes and well-known attributes, such as the AS-path, multi-exit discriminator MED, BGP local-preference, and
next hop attributes.
Standard communities, community-lists, and route-maps.
Guidelines for Configuring MDT Address Family Sessions on PE Routers for MVPN Inter-AS Support
When configuring routers for MVPN inter-AS support, follow these guidelines:
For MVPN inter-AS Option A, BGP MDT address-family peering sessions are not required between the PE routers because native
IP forwarding is used by the PE routers. For option A, BGP MDT peering sessions are only required for intra-AS VPN peering
sessions.
For MVPN inter-AS Option B, BGP MDT address-family peering sessions are only required between the PEs and ASBRs. In the Option
B inter-AS case where PE routers use iBGP to redistribute labeled VPNv4 routes to RRs of which ASBRs are clients, then BGP
MDT address-family peering sessions are required between the PEs, ASBRs, and RRs.
For MVPN inter-AS Option C, BGP MDT address-family peering sessions are only required between the PEs and RRs.
MVPN Inter-AS MDT Establishment for Option B
This section describes the sequence of events that leads to the establishment of an inter-AS MDT between the autonomous systems
in the sample inter-AS Option B topology illustrated in the following figure. For this topology, assume that all the routers
have been configured properly to support all extensions associated with the Multicast VPN Inter-AS Support feature.
Figure 4. MVPN Inter-AS Support Option B Sample Topology
The following sequence of events occur to establish an MDT default tree rooted at PE1B in this inter-AS MVPN Option B topology:
As illustrated in the following figure, PE1B advertises the default MDT information for VPN blue using the BGP MDT SAFI with
itself (PE1B) as the next hop.
Figure 5. BGP Updates from PE1B to ASBR1B
As illustrated in the following figure, ASBR1B receives the MDT SAFI information and, in turn, advertises this information
to ASBR1A with itself (ASBR1B) as the next hop.
Figure 6. BGP Updates from ASBR1B to ASBR1A
As illustrated in the following figure, ASBR1A advertises the MDT SAFI to PE1A with itself (ASBR1A) as the next hop.
Figure 7. BGP Updates from ASBR1A to PE1A
As illustrated in the following figure, PE1A learns the source PE router, the RD, and the default MDT group address from
BGP MDT SAFI updates. In addition, from the same BGP MDT SAFI updates, PE1A learns that the RPF Vector, ASBR1A, is the exit
router to source PE1B RD 55:1111. PE1A learns that P1A is an RPF neighbor through an IGP. PE1A then inserts the RPF Vector
into the PIM join and sends the PIM join that is destined for source PE1B to P1A.
Figure 8. SSM Default PIM Join from PE1A to P1A
As illustrated in the following figure, source PE1B is not reachable on P1A, but the RPF Vector ASBR1A is reachable, and
the next hop is ASBR1A, as learned from the IGP running in the core. P1A then forwards the PIM join to ASBR1A.
Figure 9. SSM Default MDT PIM Join from P1A to ASBR1A
As illustrated in the following figure, the RPF Vector, ASBR1A, is contained in the PIM join sent from P1A to ASBR1A. When
ASBR1A receives the RPF Vector, it learns that it is the exit router for source PE1B with RD 55:1111. Source PE1B is not reachable
on ASBR1A, but source PE1B, RD 55:1111, and group 232.1.1.1 are known from the BGP MDT SAFI updates. The RPF neighbor P1A
is learned from the IGP running in the core as the next hop to reach ASBR1A, which is inserted as the RPF Vector. ASBR1A then
forwards the PIM join for source PE1B to ASBR1B.
Figure 10. SSM Default MDT PIM Join from ASBR1A to ASBR1B
As illustrated in the following figure, source PE1B is reachable on ASBR1B through the IGP running in AS65. ASBR1B forwards
the PIM join to source PE1B, using PE1B as the next hop. At this point, the setup of the SSM tree for MDT default group 232.1.1.1
rooted at PE1B is complete. The SSM MDT default group rooted at PE1B, thus, has been established. The SSM trees for the MDT
default groups rooted at PE1A and PE2A follow the same procedures.
Figure 11. SSM Default MDT PIM Join from ASBR1B to PE1B
MVPN Inter-AS MDT Establishment for Option C
This section describes the sequence of events that leads to the establishment of an inter-AS MDT between the autonomous systems
in the sample inter-AS Option C topology illustrated in the following figure. For this topology, assume that all the routers
have been configured properly to support all features associated with the Multicast VPN Inter-AS Support feature.
Figure 12. MVPN Inter-AS Support Option C Sample Topology
The following sequence of events occur to establish an MDT default tree rooted at PE1B in this inter-AS MVPN Option C topology:
As illustrated in the following figure, PE1B advertises the default MDT information for VPN blue to RR1B within the BGP MDT
SAFI.
Figure 13. BGP MDT SAFI Update from PE1B to RR1B
As illustrated in the following figure, RR1B receives the MDT SAFI information, and, in turn, advertises this information
to RR1A.
Figure 14. BGP MDT SAFI Update from RR1B to RR1A
As illustrated in the following figure, RR1A receives the MDT SAFI information, and, in turn, advertises this information
to PE1A.
Figure 15. BGP MDT SAFI Update from RR1A to PE1A
As illustrated in the following figure, PE1A sends a PIM join with the Proxy Vector that identifies ASBR1A as the exit router
to reach source PE1B with RD 55:1111 and Default MDT 232.1.1.1. The Proxy Vector provides P1A and P2A a hint on how to reach
PE1B in the absence of a route to reach PE1B. Source PE1B is reachable through RPF neighbor P1A through BGP IPv4 learned updates
on PE1A.
Figure 16. PIM SSM Join for Default MDT with Proxy Vector from PE1A to P1A
As illustrated in the following figure, P1A does not know how to reach PE1B. However, the PIM join with the Proxy Vector
sent from PE1A identifies ASBR1A as being the exit router to reach source PE1B with RD 55:1111 and Default MDT 232.1.1.1.
P1A uses the Proxy Vector to reach PE1B. The RPF neighbor to reach ASBR1A is through P2A. P1A, thus, forwards the PIM SSM
join to P2A.
Figure 17. PIM SSM Join for Default MDT with Proxy Vector from P1A to P2A
As illustrated in the following figure, P2A does not know how to reach PE1B. However, the PIM join with the Proxy Vector
sent from P1A identifies ASBR1A as being the exit router to reach source PE1B with RD 55:1111 and Default MDT 232.1.1.1. P2A
uses the Proxy Vector, ASBR1A, to reach PE1B. The RPF neighbor to reach ASBR1B is through ASBR1A (that is, itself).
Figure 18. PIM SSM Join for Default MDT with Proxy Vector from P2A to ASBR1A
As illustrated in the following figure, ASBR1A receives a PIM join with Proxy Vector from P2A. ASBR1A realizes that the Proxy
Vector is itself and sends a regular PIM join towards PE1B with an RPF neighbor of ASBR1B. The PIM joins continue hop-by-hop
building the SSM Default MDT until PE1B is finally reached following standard PIM procedures.
Figure 19. PIM SSM Join for Default MDT with Proxy Vector from ASBR1A to PE1B
How to Configure Multicast VPN Inter-AS Support
Configuring the MDT Address Family in BGP for Multicast VPN Inter-AS Support
Perform this task to configure an MDT address family session on PE routers to to establish MDT peering sessions for MVPN.
The mdt keyword has been added to the address-familyipv4 command to configure an MDT address-family session.
Supported Policy
The following policy configuration parameters are supported under the BGP MDT SAFI:
Mandatory attributes and well-known attributes, such as the AS-path, multiexit discriminator (MED), BGP local preference,
and next hop attributes.
Standard communities, community lists, and route maps.
Guidelines for Configuring MDT Address Family Sessions on PE Routers for MVPN Inter-AS Support
When configuring routers for MVPN inter-AS support, follow these guidelines:
For MVPN inter-AS Option A, BGP MDT address-family peering sessions are not required between the PE routers because native
IP forwarding is used by the PE routers. For option A, BGP MDT peering sessions are only required for intra-AS VPN peering
sessions.
For MVPN inter-AS Option B, BGP MDT address-family peering sessions are only required between the PEs and ASBRs. In the Option
B inter-AS case where PE routers use iBGP to redistribute labeled VPNv4 routes to RRs of which ASBRs are clients, then BGP
MDT address-family peering sessions are required between the PEs, ASBRs, and RRs.
For MVPN inter-AS Option C, BGP MDT address-family peering sessions are only required between the PEs and RRs.
Before you begin
Before inter-AS VPN peering can be established through an MDT address family, MPLS and Cisco Express Forwarding (CEF) must
be configured in the BGP network and multiprotocol BGP on PE routers that provide VPN services to CE routers.
Note
The following policy configuration parameters are not supported:
Exits address family configuration mode and enters privileged EXEC mode.
Displaying Information About IPv4 MDT Sessions in BGP
Perform this optional task to display information about IPv4 MDT sessions in BGP.
SUMMARY STEPS
enable
showipbgpipv4mdt {all | rd | vrfvrf-name}
DETAILED STEPS
Step 1
enable
Use this command to enable privileged EXEC mode.
Enter your password if prompted.
Example:
Router> enable
Step 2
showipbgpipv4mdt {all | rd | vrfvrf-name}
Use this command to display IPv4 MDT sessions in the IPv4 BGP routing table.
The following is sample output from the showipbgpipv4mdt command with the all keyword:
Example:
Router# show ip bgp ipv4 mdt all
BGP table version is 2, local router ID is 10.1.0.2
Status codes: s suppressed, d damped, h history, * valid, > best, i - internal,
r RIB-failure, S Stale
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
Route Distinguisher: 55:1111 (default for vrf blue)
*> 10.5.5.5/32 10.1.0.1 55 0 23 24 25 54 ?
* 10.9.9.9/32 0.0.0.0 0 ?
Clearing IPv4 MDT Peering Sessions in BGP
Perform this optional task to reset IPv4 MDT address-family sessions using the mdt keyword in one of the various forms of the clearipbgpcommand. Due to the complexity of some of the keywords available for the clearipbgp command, some of the keywords are documented as separate commands.
Specifying the clearipbgpipv4mdt command with the as-numberargument resets IPv4 MDT address-family sessions associated with the specified autonomous system.
The example for this form of the clearipbgpipv4mdt command shows how to initiate a hard reset for all IPv4 MDT address-family sessions in the autonomous system numbered 65700.
or
Specifying the clearipbgpipv4mdt command with the peer-group keyword resets IPv4 MDT address-family sessions for all members of a BGP peer group.
The example for this form of the clearipbgpipv4mdt command shows how to initiate a soft reset for inbound MDT address-family sessions with members of the peer group test. Outbound
sessions are unaffected.
or
Specifying the clearipbgpipv4mdt command with the update-group keyword resets IPv4 MDT address-family sessions for all the members of a BGP update group.
The example for this form of the clearipbgpipv4mdt command shows how to reset for all members of the update group 3.
Configuring a PE Router to Send BGP MDT Updates to Build the Default MDT for MVPN Inter-AS Support - Option B
Perform this task to configure PE routers in an Option B deployment to support the extensions necessary (BGP connector attribute,
BGP MDT SAFI, and RPF Vector) to send BGP MDT updates to build the default MDT for MVPN inter-AS support.
SUMMARY STEPS
enable
configureterminal
routerbgpas-number
neighborip-addressremote-asas-number
address-familyipv4mdt
neighborneighbor-addressactivate
neighborneighbor-addressnext-hop-self
exit
address-familyvpnv4
neighborneighbor-addressactivate
neighborneighbor-addresssend-communityextended
end
DETAILED STEPS
Command or Action
Purpose
Step 1
enable
Example:
Router> enable
Enables privileged EXEC mode.
Enter your password if prompted.
Step 2
configureterminal
Example:
Router# configure terminal
Enters global configuration mode.
Step 3
routerbgpas-number
Example:
Router(config)# router bgp 101
Enters router configuration mode for the specified routing process.
Enables the standard and extended community attributes to be sent to this neighbor.
Step 12
end
Example:
Router(config-router-af)# end
Exits address family configuration mode and returns to privileged EXEC mode.
Configuring a PE Router to Send BGP MDT Updates to Build the Default MDT for MVPN Inter-AS Support - Option C
Perform this task to configure PE routers in an Option B deployment to support the extensions necessary (BGP connector attribute,
BGP MDT SAFI, and RPF Vector) to send BGP MDT updates to build the default MDT for MVPN inter-AS support.
SUMMARY STEPS
enable
configureterminal
routerbgpas-number
neighborip-addressremote-asas-number
address-familyipv4mdt
neighborneighbor-addressactivate
neighborneighbor-addresssend-communityextended
exit
address-familyvpnv4
neighborneighbor-addressactivate
neighborneighbor-addresssend-communityextended
end
DETAILED STEPS
Command or Action
Purpose
Step 1
enable
Example:
Router> enable
Enables privileged EXEC mode.
Enter your password if prompted.
Step 2
configureterminal
Example:
Router# configure terminal
Enters global configuration mode.
Step 3
routerbgpas-number
Example:
Router(config)# router bgp 101
Enters router configuration mode for the specified routing process.
Use this command to display the PIM neighbors discovered by PIMv1 router query messages or PIMv2 hello messages.
The P flag indicates that the neighbor has announced (through PIM hello messages) its capability to handle RPF Vectors in
PIM join messages. All software versions that support the PIM RPF Vector feature announce this PIM hello option. An RPF Vector
is only included in PIM messages when all PIM neighbors on an RPF interface support it.
The following is sample output from the showippimneighbor command:
Example:
Router# show ip pim neighbor
PIM Neighbor Table
Mode: B - Bidir Capable, DR - Designated Router, N - Default DR Priority,
S - State Refresh Capable
Neighbor Interface Uptime/Expires Ver DR
Address Prio/Mode
10.0.0.1 GigabitEthernet10/2 00:01:29/00:01:15 v2 1 / S
10.0.0.3 GigabitEthernet10/3 00:01:15/00:01:28 v2 1 / DR S P
Use this command to display information about how IP multicast routing does RPF.
The following is sample output from the showiprpfcommand:
Example:
Router# show ip rpf 10.7.0.7 232.1.1.1 rd 55:1111
RPF information for ? (10.7.0.7)
RPF interface: GigabitEthernet2/2
RPF neighbor: ? (10.0.1.3)
RPF route/mask: 10.5.0.5/32
RPF type: unicast (UNKNOWN)
RPF recursion count: 0
Doing distance-preferred lookups across tables
BGP lookup of 55:1111/10.7.0.7 next_hop: 10.5.0.5
PROXY vector: 10.5.0.5
Step 5
showippim [vrfvrf-name] mdtbgp
Use this command to display information about the BGP advertisement of RDs for the MDT default group.
The following is sample output from the showippimmdtbgp command:
Example:
Router# show ip pim mdt bgp
MDT (Route Distinguisher + IPv4) Router ID Next Hop
MDT group 232.1.1.1
55:1111:192.168.0.2 192.168.0.2 192.168.0.2
55:1111:192.168.0.8 192.168.0.4 192.168.0.4
Configuration Examples for Multicast VPN Inter-AS Support
Configuring an IPv4 MDT Address-Family Session for Multicast VPN Inter-AS Support Example
The following examples shows how to configure a router to support an IPv4 MDT address-family session with the BGP neighbor
at 10.1.1.2:
Configuring a PE Router to Send BGP MDT Updates to Build the Default MDT for MVPN Inter-AS Support
The following example shows how to configure a PE router to support the extensions necessary (BGP connector attribute, BGP
MDT SAFI, and RPF Vector) to send BGP MDT updates to build the default MDT for MVPN inter-AS support in an Option B deployment.
Only the relevant configuration is shown in this example.
Configuring a PE Router to Send BGP MDT Updates to Build the Default MDT for MVPN Inter-AS Support
The following example shows how to configure a PE router to support the extensions necessary (BGP connector attribute, BGP
MDT SAFI, and RPF Vector) to send BGP MDT updates to build the default MDT for MVPN inter-AS support in an Option B deployment.
Only the relevant configuration is shown in this example.
!
ip multicast-routing
ip multicast-routing vrf blue
ip multicast rpf proxy vector
!
.
.
.
!
router bgp 65
.
.
.
!
address-family ipv4
neighbor 10.252.252.10 activate
neighbor 10.252.252.10 send-label
no auto-summary
no synchronization
exit-address-family
!
address-family ipv4 mdt
neighbor 10.252.252.10 activate
neighbor 10.252.252.10 send-community extended
exit-address-family
!
address-family vpnv4
neighbor 10.252.252.10 activate
neighbor 10.252.252.10 send-community extended
exit-address-family
!
.
.
.
!
ip pim ssm default
!
Configuring Back-to-Back ASBR PEs - Option A Example
The following example shows how to configure support for MVPN inter-AS support Option A. This configuration example is based
on the sample inter-AS network Option A topology illustrated in the figure.
In this configuration example, PE3A in AS1 is attached directly to PE3B in AS2. The two PE routers are attached by physical
interfaces, one physical interface for each of the VPNs (VPN blue and VPN green) whose routes need to be passed from AS1 to
AS2, and vice versa. Each PE will treat the other as if it were a CE router; that is, the PEs associate each interface with
a VRF and use eBGP to distribute unlabeled IPv4 addresses to each other. Intermediate System-to-Intermediate System (IS-IS)
is being used for the BGP peerings in both autonomous systems, and Routing Information Protocol (RIP) is being used on the
PE routers that face the CE routers to dynamically learn the routes from the VRFs and advertise them as VPNv4 routes to the
remote PE routers. RIP is also being used between the ASBRs to set up the eBGP peerings between PE3A and PE3B.
Note
For Option A, any IGP can be used to exchange the IPv4 routes for the loopback interfaces.
Figure 20. Topology for MVPN Inter-AS Support Option A Configuration Example
The table provides information about the topology used for the Option A configuration example presented in this section.
Table 1. Topology Information for MVPN Inter-AS Option A Configuration Example
PE Router
VPN
RD
AS Number
Loopback0 Interface
Default MDT (PIM-SSM)
PE1A
green
55:1111
1
10.1.1.1/32
232.1.1.1
PE2A
blue
55:1111
1
10.1.1.2/32
232.1.1.1
PE3A
blue/green
55:1111
1
10.1.1.3/32
232.1.1.1
PE1B
green
55:2222
2
10.2.2.1/32
232.2.2.2
PE2B
blue
55:2222
2
10.2.2.2/32
232.2.2.2
PE3B
blue/green
55:2222
2
10.2.2.3/32
232.2.2.2
PE1A
!
version 12.0
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname PE1A
!
boot-start-marker
boot-end-marker
!
!
ip subnet-zero
ip cef
no ip domain-lookup
ip vrf green
rd 55:2222
route-target export 55:2222
route-target import 55:2222
mdt default 232.2.2.2
!
ip multicast-routing
ip multicast-routing vrf green
mpls label protocol ldp
!
!
!
interface Loopback0
ip address 10.1.1.1 255.255.255.255
no ip directed-broadcast
ip router isis
ip pim sparse-mode
!
interface GigabitEthernet0/0
ip vrf forwarding green
ip address 172.25.11.1 255.255.255.0
no ip directed-broadcast
ip pim sparse-mode
tag-switching ip
!
interface GigabitEthernet1/0
ip address 172.30.41.1 255.255.255.0
no ip directed-broadcast
ip router isis
ip pim sparse-mode
tag-switching ip
!
router isis
net 49.0000.0000.1111.00
!
router rip
version 2
!
address-family ipv4 vrf green
version 2
network 172.25.0.0
no auto-summary
exit-address-family
!
router bgp 1
no synchronization
bgp log-neighbor-changes
neighbor 10.1.1.2 remote-as 1
neighbor 10.1.1.2 update-source Loopback0
neighbor 10.1.1.3 remote-as 1
neighbor 10.1.1.3 update-source Loopback0
no auto-summary
!
address-family ipv4 mdt
neighbor 10.1.1.2 activate
neighbor 10.1.1.3 activate
exit-address-family
!
address-family vpnv4
neighbor 10.1.1.2 activate
neighbor 10.1.1.2 send-community extended
neighbor 10.1.1.3 activate
neighbor 10.1.1.3 send-community extended
exit-address-family
!
address-family ipv4 vrf green
redistribute rip metric 1
no synchronization
exit-address-family
!
ip classless
!
ip pim ssm default
ip pim vrf green send-rp-announce GigabitEthernet0/0 scope 32
ip pim vrf green send-rp-discovery 0/0 scope 32
ip pim vrf green register-rate-limit 2
!
!
!
control-plane
!
!
line con 0
line aux 0
line vty 0 4
login
!
no cns aaa enable
end
PE2A
!
version 12.0
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname PE2A
!
boot-start-marker
boot-end-marker
!
!
ip subnet-zero
ip cef
no ip domain-lookup
ip vrf blue
rd 55:1111
route-target export 55:1111
route-target import 55:1111
mdt default 232.1.1.1
!
ip multicast-routing
ip multicast-routing vrf blue
mpls label protocol ldp
!
!
!
interface Loopback0
ip address 10.1.1.2 255.255.255.255
no ip directed-broadcast
ip router isis
ip pim sparse-mode
!
interface GigabitEthernet0/0
ip vrf forwarding blue
ip address 172.17.12.2 255.255.255.0
no ip directed-broadcast
ip pim sparse-mode
tag-switching ip
!
interface GigabitEthernet1/0
no ip address
no ip directed-broadcast
shutdown
!
interface GigabitEthernet2/0
ip address 172.19.142.2 255.255.255.0
no ip directed-broadcast
ip router isis
ip pim sparse-mode
tag-switching ip
!
router isis
net 49.0000.0000.2222.00
!
router rip
version 2
!
address-family ipv4 vrf blue
version 2
network 172.17.0.0
no auto-summary
exit-address-family
!
router bgp 1
no synchronization
bgp log-neighbor-changes
neighbor 10.1.1.1 remote-as 1
neighbor 10.1.1.1 update-source Loopback0
neighbor 10.1.1.3 remote-as 1
neighbor 10.1.1.3 update-source Loopback0
no auto-summary
!
address-family ipv4 mdt
neighbor 10.1.1.1 activate
neighbor 10.1.1.3 activate
exit-address-family
!
address-family vpnv4
neighbor 10.1.1.1 activate
neighbor 10.1.1.1 send-community extended
neighbor 10.1.1.3 activate
neighbor 10.1.1.3 send-community extended
exit-address-family
!
address-family ipv4 vrf blue
redistribute rip metric 1
no synchronization
exit-address-family
!
ip classless
!
ip pim ssm default
ip pim vrf blue send-rp-announce GigabitEthernet0/0 scope 32
ip pim vrf blue send-rp-discovery GigabitEthernet0/0 scope 32
ip pim vrf blue ssm default
!
!
!
control-plane
!
!
line con 0
line aux 0
line vty 0 4
login
!
no cns aaa enable
end
PE3A
!
version 12.0
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname PE3A
!
boot-start-marker
boot-end-marker
!
!
ip subnet-zero
ip cef
no ip domain-lookup
ip vrf blue
rd 55:1111
route-target export 55:1111
route-target import 55:1111
mdt default 232.1.1.1
!
ip vrf green
rd 55:2222
route-target export 55:2222
route-target import 55:2222
mdt default 232.2.2.2
!
ip multicast-routing
ip multicast-routing vrf blue
ip multicast-routing vrf green
mpls label protocol ldp
!
!
!
interface Loopback0
ip address 10.1.1.3 255.255.255.255
no ip directed-broadcast
ip router isis
ip pim sparse-mode
!
interface GigabitEthernet0/0
no ip address
no ip directed-broadcast
shutdown
!
interface GigabitEthernet1/0
no ip address
no ip directed-broadcast
shutdown
!
interface GigabitEthernet2/0
no ip address
no ip directed-broadcast
shutdown
!
interface GigabitEthernet3/0
ip address 192.168.143.3 255.255.255.0
no ip directed-broadcast
ip router isis
ip pim sparse-mode
tag-switching ip
!
interface GigabitEthernet4/0
ip vrf forwarding blue
ip address 172.20.34.3 255.255.255.0
no ip directed-broadcast
ip pim sparse-dense-mode
tag-switching ip
!
interface GigabitEthernet5/0
ip vrf forwarding green
ip address 172.23.35.3 255.255.255.0
no ip directed-broadcast
ip pim sparse-dense-mode
tag-switching ip
!
router eigrp 1
!
address-family ipv4 vrf blue
network 172.20.0.0
no auto-summary
exit-address-family
!
router isis
net 49.0000.0000.3333.00
!
router rip
version 2
!
address-family ipv4 vrf green
version 2
redistribute bgp 1 metric 2
network 172.23.0.0
no auto-summary
exit-address-family
!
address-family ipv4 vrf blue
version 2
redistribute bgp 1 metric 1
network 172.20.0.0
no auto-summary
exit-address-family
!
router bgp 1
no synchronization
bgp log-neighbor-changes
neighbor 10.1.1.1 remote-as 1
neighbor 10.1.1.1 update-source Loopback0
neighbor 10.1.1.2 remote-as 1
neighbor 10.1.1.2 update-source Loopback0
no auto-summary
!
address-family ipv4 mdt
neighbor 10.1.1.1 activate
neighbor 10.1.1.2 activate
exit-address-family
!
address-family vpnv4
neighbor 10.1.1.1 activate
neighbor 10.1.1.1 send-community extended
neighbor 10.1.1.2 activate
neighbor 10.1.1.2 send-community extended
bgp redistribute-internal
exit-address-family
!
address-family ipv4 vrf green
no synchronization
bgp redistribute-internal
exit-address-family
!
address-family ipv4 vrf blue
redistribute rip
no synchronization
bgp redistribute-internal
exit-address-family
!
ip classless
!
ip pim ssm default
ip pim vrf blue ssm default
!
!
!
control-plane
!
!
line con 0
line aux 0
line vty 0 4
login
!
no cns aaa enable
end
PE3B
!
version 12.0
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname PE3B
!
boot-start-marker
boot-end-marker
!
!
ip subnet-zero
ip cef
no ip domain-lookup
ip vrf blue
rd 55:1111
route-target export 55:1111
route-target import 55:1111
mdt default 232.1.1.1
!
ip vrf green
rd 55:2222
route-target export 55:2222
route-target import 55:2222
mdt default 232.2.2.2
!
ip multicast-routing
ip multicast-routing vrf blue
ip multicast-routing vrf green
mpls label protocol ldp
!
!
!
interface Loopback0
ip address 10.2.2.3 255.255.255.255
no ip directed-broadcast
ip router isis
ip pim sparse-mode
!
interface GigabitEthernet0/0
no ip address
no ip directed-broadcast
shutdown
!
interface GigabitEthernet1/0
no ip address
no ip directed-broadcast
shutdown
!
interface GigabitEthernet2/0
no ip address
no ip directed-broadcast
shutdown
!
interface GigabitEthernet3/0
ip address 172.16.43.3 255.255.255.0
no ip directed-broadcast
ip router isis
ip pim sparse-mode
tag-switching ip
!
interface GigabitEthernet4/0
ip vrf forwarding blue
ip address 172.20.34.4 255.255.255.0
no ip directed-broadcast
ip pim sparse-dense-mode
tag-switching ip
!
interface GigabitEthernet5/0
ip vrf forwarding green
ip address 172.23.35.4 255.255.255.0
no ip directed-broadcast
ip pim sparse-dense-mode
tag-switching ip
!
router isis
net 49.0000.0000.3333.00
!
router rip
version 2
!
address-family ipv4 vrf green
version 2
network 172.23.0.0
no auto-summary
exit-address-family
!
address-family ipv4 vrf blue
version 2
network 172.20.0.0
no auto-summary
exit-address-family
!
router bgp 2
no synchronization
bgp log-neighbor-changes
redistribute rip metric 1
neighbor 10.2.2.1 remote-as 2
neighbor 10.2.2.1 update-source Loopback0
neighbor 10.2.2.2 remote-as 2
neighbor 10.2.2.2 update-source Loopback0
no auto-summary
!
address-family ipv4 mdt
neighbor 10.2.2.1 activate
neighbor 10.2.2.2 activate
exit-address-family
!
address-family vpnv4
neighbor 10.2.2.1 activate
neighbor 10.2.2.1 send-community extended
neighbor 10.2.2.2 activate
neighbor 10.2.2.2 send-community extended
exit-address-family
!
address-family ipv4 vrf green
redistribute rip
no synchronization
exit-address-family
!
address-family ipv4 vrf blue
redistribute rip
no synchronization
exit-address-family
!
ip classless
!
ip pim ssm default
ip pim vrf blue ssm default
!
!
!
control-plane
!
!
line con 0
line aux 0
line vty 0 4
login
!
no cns aaa enable
end
PE2B
!
version 12.0
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname PE2B
!
boot-start-marker
boot-end-marker
!
!
ip subnet-zero
ip cef
no ip domain-lookup
ip vrf blue
rd 55:1111
route-target export 55:1111
route-target import 55:1111
mdt default 232.1.1.1
!
ip multicast-routing
ip multicast-routing vrf blue
mpls label protocol ldp
!
!
!
interface Loopback0
ip address 10.2.2.2 255.255.255.255
no ip directed-broadcast
ip router isis
ip pim sparse-mode
!
interface GigabitEthernet0/0
ip vrf forwarding blue
ip address 172.18.22.2 255.255.255.0
no ip directed-broadcast
ip pim sparse-mode
tag-switching ip
!
interface GigabitEthernet1/0
no ip address
no ip directed-broadcast
shutdown
!
interface GigabitEthernet2/0
ip address 172.19.42.2 255.255.255.0
no ip directed-broadcast
ip router isis
ip pim sparse-mode
tag-switching ip
!
router isis
net 49.0000.0000.2222.00
!
router rip
!
address-family ipv4 vrf blue
network 172.18.0.0
no auto-summary
exit-address-family
!
router bgp 2
no synchronization
bgp log-neighbor-changes
neighbor 10.2.2.1 remote-as 2
neighbor 10.2.2.1 update-source Loopback0
neighbor 10.2.2.3 remote-as 2
neighbor 10.2.2.3 update-source Loopback0
no auto-summary
!
address-family ipv4 mdt
neighbor 10.2.2.1 activate
neighbor 10.2.2.3 activate
exit-address-family
!
address-family vpnv4
neighbor 10.2.2.1 activate
neighbor 10.2.2.1 send-community extended
neighbor 10.2.2.3 activate
neighbor 10.2.2.3 send-community extended
exit-address-family
!
address-family ipv4 vrf blue
no synchronization
exit-address-family
!
ip classless
!
ip pim ssm default
ip pim vrf blue ssm default
!
!
!
control-plane
!
!
line con 0
line aux 0
line vty 0 4
login
!
no cns aaa enable
end
PE1B
!
version 12.0
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname PE1B
!
boot-start-marker
boot-end-marker
!
!
ip subnet-zero
ip cef
no ip domain-lookup
ip vrf green
rd 55:2222
route-target export 55:2222
route-target import 55:2222
mdt default 232.2.2.2
!
ip multicast-routing
ip multicast-routing vrf green
mpls label protocol ldp
!
!
!
interface Loopback0
ip address 10.2.2.1 255.255.255.255
no ip directed-broadcast
ip router isis
ip pim sparse-mode
!
interface GigabitEthernet0/0
ip vrf forwarding green
ip address 172.25.111.1 255.255.255.0
no ip directed-broadcast
ip pim sparse-mode
tag-switching ip
!
interface GigabitEthernet1/0
ip address 172.30.141.1 255.255.255.0
no ip directed-broadcast
ip router isis
ip pim sparse-mode
tag-switching ip
!
router isis
net 49.0000.0000.1111.00
!
router rip
version 2
!
address-family ipv4 vrf green
version 2
network 172.25.0.0
no auto-summary
exit-address-family
!
router bgp 2
no synchronization
bgp log-neighbor-changes
neighbor 10.2.2.2 remote-as 2
neighbor 10.2.2.2 update-source Loopback0
neighbor 10.2.2.3 remote-as 2
neighbor 10.2.2.3 update-source Loopback0
no auto-summary
!
address-family ipv4 mdt
neighbor 10.2.2.2 activate
neighbor 10.2.2.3 activate
exit-address-family
!
address-family vpnv4
neighbor 10.2.2.2 activate
neighbor 10.2.2.2 send-community extended
neighbor 10.2.2.3 activate
neighbor 10.2.2.3 send-community extended
exit-address-family
!
address-family ipv4 vrf green
no synchronization
exit-address-family
!
ip classless
!
ip pim ssm default
!
!
!
control-plane
!
!
line con 0
line aux 0
line vty 0 4
login
!
no cns aaa enable
end
Configuring the Exchange of VPNv4 Routes Directly Between ASBRs - Option B Example
The following example shows how to configure MVPN inter-AS support in an Option B deployment. This configuration is based
on the sample inter-AS topology illustrated in the figure.
In this configuration example, PE1A and PE2A are configured to use iBGP to redistribute labeled VPNv4 routes to each other
and to ASBR1A, and PE1B is configured to redistribute labeled VPNv4 routes to ASBR1B. ASBR1A and ASBR1B are configured to
use eBGP to exchange those labeled VPNv4 routes to each other.
Figure 21. Topology for MVPN Inter-AS Support Option B Configuration Example
The table provides information about the topology used for this particular Option B configuration example.
Table 2. Topology Information for MVPN Inter-AS Support Option B Configuration Example
PE or ASBR Router
AS Number
Loopback0 Interfaces
Default MDT (PIM-SSM)
PE1A
55
192.168.0.1/32
232.1.1.1
PE2A
55
192.168.0.2/32
232.1.1.1
ASBR1A
55
192.168.0.4/32
232.1.1.1
ASBR1B
65
192.168.0.9/32
232.1.1.1
PE1B
65
192.168.0.8/32
232.1.1.1
PE1A
!
ip vrf blue
rd 55:1111
mdt default 232.1.1.1
!
ip multicast-routing
ip multicast-routing vrf blue
ip multicast vrf blue rpf proxy rd vector
!
.
.
.
!
interface GigabitEthernet0/0
ip vrf forwarding blue
ip pim sparse-mode
!
.
.
.
!
router bgp 55
no synchronization
bgp log-neighbor-changes
neighbor 192.168.0.2 remote-as 55
neighbor 192.168.0.2 update-source Loopback0
neighbor 192.168.0.4 remote-as 55
neighbor 192.168.0.4 update-source Loopback0
no auto-summary
!
address-family ipv4 mdt
neighbor 192.168.0.2 activate
neighbor 192.168.0.2 next-hop-self
neighbor 192.168.0.4 activate
neighbor 192.168.0.4 next-hop-self
exit-address-family
!
address-family vpnv4
neighbor 192.168.0.2 activate
neighbor 192.168.0.2 send-community extended
neighbor 192.168.0.4 activate
neighbor 192.168.0.4 send-community extended
exit-address-family
!
address-family ipv4 vrf blue
redistribute connected
redistribute static
redistribute rip metric 50
no auto-summary
no synchronization
exit-address-family
!
.
.
.
!
ip pim ssm default
!
PE2A
!
ip vrf blue
rd 55:1111
mdt default 232.1.1.1
!
ip multicast-routing
ip multicast-routing vrf blue
ip multicast vrf blue rpf proxy rd vector
!
.
.
.
!
interface GigabitEthernet0/0
ip vrf forwarding blue
ip pim sparse-mode
!
.
.
.
!
router bgp 55
neighbor 192.168.0.1 remote-as 55
neighbor 192.168.0.1 update-source Loopback0
neighbor 192.168.0.4 remote-as 55
neighbor 192.168.0.4 update-source Loopback0
!
address-family ipv4 mdt
neighbor 192.168.0.1 activate
neighbor 192.168.0.1 next-hop-self
neighbor 192.168.0.4 activate
neighbor 192.168.0.4 next-hop-self
exit-address-family
!
address-family vpnv4
neighbor 192.168.0.1 activate
neighbor 192.168.0.1 send-community extended
neighbor 192.168.0.4 activate
neighbor 192.168.0.4 send-community extended
exit-address-family
!
address-family ipv4 vrf blue
redistribute connected
redistribute static
no synchronization
exit-address-family
!
.
.
.
!
ip pim ssm default
!
!
ip vrf blue
rd 55:1111
mdt default 232.1.1.1
!
ip multicast-routing
ip multicast-routing vrf blue
ip multicast vrf blue rpf proxy rd vector
!
.
.
.
!
interface GigabitEthernet0/0
ip vrf forwarding blue
ip pim sparse-mode
!
.
.
.
!
router bgp 65
neighbor 192.168.0.9 remote-as 65
neighbor 192.168.0.9 update-source Loopback0
!
address-family ipv4 mdt
neighbor 192.168.0.9 activate
neighbor 192.168.0.9 next-hop-self
exit-address-family
!
address-family vpnv4
neighbor 192.168.0.9 activate
neighbor 192.168.0.9 send-community extended
exit-address-family
!
address-family ipv4 vrf blue
redistribute connected
redistribute static
redistribute rip metric 50
no synchronization
exit-address-family
!
.
.
.
!
ip pim ssm default
!
The following is sample output from the
showippimmdtbgp command for PE1A, PE2A, and PE1B. The sample output displays information about the BGP advertisement of RDs for the MDT default
group 232.1.1.1. The output displays the MDT default groups advertised, the RDs and source addresses of sources sending to
the MDT default groups, the BGP router ID of the advertising routers, and the BGP next hop address contained in the advertisements.
PE1A# show ip pim mdt bgp
MDT (Route Distinguisher + IPv4) Router ID Next Hop
MDT group 232.1.1.1
55:1111:192.168.0.2 192.168.0.2 192.168.0.2
55:1111:192.168.0.8 192.168.0.4 192.168.0.4
PE2A# show ip pim mdt bgp
MDT (Route Distinguisher + IPv4) Router ID Next Hop
MDT group 232.1.1.1
55:1111:192.168.0.1 192.168.0.1 192.168.0.1
55:1111:192.168.0.8 192.168.0.4 192.168.0.4
PE1B# show ip pim mdt bgp
MDT (Route Distinguisher + IPv4) Router ID Next Hop
MDT group 232.1.1.1
55:1111:192.168.0.1 192.168.0.9 192.168.0.9
55:1111:192.168.0.2 192.168.0.9 192.168.0.9
The following are sample outputs from the
showipmrouteproxy command for PE1A, PE2A, and PE1B. The output displays information about the RPF Vectors learned by each PE router in this
configuration example. The RPF Vector is the exit address of the ASBR router through which PIM messages are sent to reach
inter-AS sources. The “Proxy” field displays the RPF Vectors learned by the PE routers. Each RPF Vector listed under the “Proxy”
field is prepended by the RD associated with the RPF Vector. Because the PE routers are the assigners of the RPF Vector (that
is, the PE routers insert the RPF Vector into PIM joins), 0.0.0.0 is the address displayed under the “Assigner” field in all
the sample outputs. Finally, because PE routers learn the RPF Vector from BGP MDT SAFI updates, BGP MDT is displayed as the
origin under the “Origin” field in all the outputs.
PE1A# show ip mroute proxy
(192.168.0.8, 232.1.1.1)
Proxy Assigner Origin Uptime/Expire
55:1111/192.168.0.4 0.0.0.0 BGP MDT 00:13:07/stopped
PE2A# show ip mroute proxy
(192.168.0.8, 232.1.1.1)
Proxy Assigner Origin Uptime/Expire
55:1111/192.168.0.4 0.0.0.0 BGP MDT 00:14:28/stopped
PE1B# show ip mroute proxy
(192.168.0.1, 232.1.1.1)
Proxy Assigner Origin Uptime/Expire
55:1111/192.168.0.9 0.0.0.0 BGP MDT 00:35:19/stopped
(192.168.0.2, 232.1.1.1)
Proxy Assigner Origin Uptime/Expire
55:1111/192.168.0.9 0.0.0.0 BGP MDT 00:35:49/stopped
The following is sample output from the
showipmrouteproxy command from P1A. Because P routers learn the RPF Vector from the PIM joins sent from PE routers, the IP addresses of PE1A
(10.0.3.1) and PE2A (10.0.3.2) are displayed under the “Assigner” field in the output for P1A. Because P1A learns the RPF
Vector from encodings in the PIM join message, PIM is displayed as the origin under the “Origin” field.
P1A# show ip mroute proxy
(192.168.0.8, 232.1.1.1)
Proxy Assigner Origin Uptime/Expire
55:1111/192.168.0.4 10.0.3.1 PIM 00:03:29/00:02:06
55:1111/192.168.0.4 10.0.3.2 PIM 00:17:47/00:02:06
The following is sample output from the
showipmrouteproxy command for ASBR1A and ASBR1B. If a router receives an RPF Vector that references a local interface (which occurs in an Option
B deployment when an ASBR receives a RPF Vector owned by a local interface), the router discards the RPF Vector and performs
a normal RPF lookup using information that the router learned from BGP MDT SAFI updates. In the output for all ASBR routers,
under the “Proxy” field, the word “local” is displayed instead of the RPF Vector because ASBR1A and ASBR1B are using local
interfaces to perform RPF lookups for PIM joins with RPF Vectors that reference one of their local interfaces. The “Assigner”
field displays the RPF address that sent the PIM join to the ASBR. Because the ASBRs learn the RPF Vectors from the PIM joins
(the RPF Vectors that are subsequently discarded), PIM is displayed as the origin under the “Origin” field.
The following is sample output from the
showipmroute command for PE1A, PE2A, P1A, ASBR1A, ASBR1B, and PE1B. The sample outputs show the global table for the MDT default group
232.1.1.1. The output from this command confirms that all three PE routers (PE1A, PE2A, and PE1B) have joined the default
MDT.
PE1A
PE1A# show ip mroute 232.1.1.1
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report,
Z - Multicast Tunnel, z - MDT-data group sender,
Y - Joined MDT-data group, y - Sending to MDT-data group
V - RD & Vector, v - Vector
Outgoing interface flags: H - Hardware switched, A - Assert winner
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(192.168.0.8, 232.1.1.1), 00:13:11/00:02:41, flags: sTIZV
Incoming interface: GigabitEthernet2/0, RPF nbr 10.0.3.3, vector 192.168.0.4
Outgoing interface list:
MVRF blue, Forward/Sparse-Dense, 00:13:11/00:00:00
(192.168.0.2, 232.1.1.1), 00:13:12/00:02:41, flags: sTIZ
Incoming interface: GigabitEthernet2/0, RPF nbr 10.0.3.2
Outgoing interface list:
MVRF blue, Forward/Sparse-Dense, 00:13:12/00:00:00
(192.168.0.1, 232.1.1.1), 00:13:12/00:03:27, flags: sT
Incoming interface: Loopback0, RPF nbr 0.0.0.0
Outgoing interface list:
GigabitEthernet2/0, Forward/Sparse-Dense, 00:13:11/00:02:50
PE2A
PE2A# show ip mroute 232.1.1.1
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report,
Z - Multicast Tunnel, z - MDT-data group sender,
Y - Joined MDT-data group, y - Sending to MDT-data group
V - RD & Vector, v - Vector
Outgoing interface flags: H - Hardware switched, A - Assert winner
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(192.168.0.8, 232.1.1.1), 00:17:05/00:02:46, flags: sTIZV
Incoming interface: GigabitEthernet2/0, RPF nbr 10.0.3.3, vector 192.168.0.4
Outgoing interface list:
MVRF blue, Forward/Sparse-Dense, 00:17:05/00:00:00
(192.168.0.1, 232.1.1.1), 00:17:05/00:02:46, flags: sTIZ
Incoming interface: GigabitEthernet2/0, RPF nbr 10.0.3.1
Outgoing interface list:
MVRF blue, Forward/Sparse-Dense, 00:17:05/00:00:00
(192.168.0.2, 232.1.1.1), 00:17:06/00:03:15, flags: sT
Incoming interface: Loopback0, RPF nbr 0.0.0.0
Outgoing interface list:
GigabitEthernet2/0, Forward/Sparse-Dense, 00:17:06/00:03:08
P1A
P1A# show ip mroute 232.1.1.1
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report,
Z - Multicast Tunnel, z - MDT-data group sender,
Y - Joined MDT-data group, y - Sending to MDT-data group
V - RD & Vector, v - Vector
Outgoing interface flags: H - Hardware switched, A - Assert winner
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(192.168.0.1, 232.1.1.1), 00:17:43/00:03:08, flags: sT
Incoming interface: GigabitEthernet2/0, RPF nbr 10.0.3.1
Outgoing interface list:
GigabitEthernet3/0, Forward/Sparse-Dense, 00:17:43/00:02:51
(192.168.0.8, 232.1.1.1), 00:18:12/00:03:15, flags: sTV
Incoming interface: GigabitEthernet3/0, RPF nbr 10.0.4.4, vector 192.168.0.4
Outgoing interface list:
GigabitEthernet2/0, Forward/Sparse-Dense, 00:18:12/00:03:15
(192.168.0.2, 232.1.1.1), 00:18:13/00:03:18, flags: sT
Incoming interface: GigabitEthernet2/0, RPF nbr 10.0.3.2
Outgoing interface list:
GigabitEthernet3/0, Forward/Sparse-Dense, 00:18:13/00:03:18
ASBR1A
ASBR1A# show ip mroute 232.1.1.1
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report,
Z - Multicast Tunnel, z - MDT-data group sender,
Y - Joined MDT-data group, y - Sending to MDT-data group
V - RD & Vector, v - Vector
Outgoing interface flags: H - Hardware switched, A - Assert winner
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(10.254.254.8, 232.1.1.1), 00:20:13/00:03:16, flags: sT
Incoming interface: GigabitEthernet6/0, RPF nbr 10.0.7.12
Outgoing interface list:
GigabitEthernet5/0, Forward/Sparse-Dense, 00:20:13/00:02:46
(10.254.254.2, 232.1.1.1), 00:20:13/00:03:16, flags: sT
Incoming interface: GigabitEthernet5/0, RPF nbr 10.0.6.5
Outgoing interface list:
GigabitEthernet6/0, Forward/Sparse-Dense, 00:20:13/00:02:39
ASBR1B
ASBR1B# show ip mroute 232.1.1.1
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report,
Z - Multicast Tunnel, z - MDT-data group sender,
Y - Joined MDT-data group, y - Sending to MDT-data group
V - RD & Vector, v - Vector
Outgoing interface flags: H - Hardware switched, A - Assert winner
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(192.168.0.1, 232.1.1.1), 00:37:43/00:03:16, flags: sTV
Incoming interface: GigabitEthernet4/0, RPF nbr 10.0.5.4, vector 10.0.5.4
Outgoing interface list:
GigabitEthernet6/0, Forward/Sparse-Dense, 00:37:43/00:03:10
(192.168.0.8, 232.1.1.1), 00:38:14/00:03:16, flags: sT
Incoming interface: GigabitEthernet6/0, RPF nbr 10.0.7.8
Outgoing interface list:
GigabitEthernet4/0, Forward/Sparse-Dense, 00:38:14/00:02:45
(192.168.0.2, 232.1.1.1), 00:38:14/00:03:16, flags: sTV
Incoming interface: GigabitEthernet4/0, RPF nbr 10.0.5.4, vector 10.0.5.4
Outgoing interface list:
GigabitEthernet6/0, Forward/Sparse-Dense, 00:38:14/00:02:45
PE1B
PE1B# show ip mroute 232.1.1.1
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report,
Z - Multicast Tunnel, z - MDT-data group sender,
Y - Joined MDT-data group, y - Sending to MDT-data group
V - RD & Vector, v - Vector
Outgoing interface flags: H - Hardware switched, A - Assert winner
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(192.168.0.1, 232.1.1.1), 00:35:23/00:02:40, flags: sTIZV
Incoming interface: GigabitEthernet6/0, RPF nbr 10.0.7.9, vector 192.168.0.9
Outgoing interface list:
MVRF blue, Forward/Sparse-Dense, 00:35:23/00:00:00
(192.168.0.2, 232.1.1.1), 00:35:53/00:02:40, flags: sTIZV
Incoming interface: GigabitEthernet6/0, RPF nbr 10.0.7.9, vector 192.168.0.9
Outgoing interface list:
MVRF blue, Forward/Sparse-Dense, 00:35:53/00:00:00
(192.168.0.8, 232.1.1.1), 00:35:53/00:03:10, flags: sT
Incoming interface: Loopback0, RPF nbr 0.0.0.0
Outgoing interface list:
GigabitEthernet6/0, Forward/Sparse-Dense, 00:35:53/00:02:35
Configuring the Exchange of VPNv4 Routes Between RRs Using Multihop MP-EBGP
The following example shows how to configure support for MVPN inter-AS option C. This configuration is based on the sample
inter-AS topology illustrated in the figure.
In the configuration example, MP-eBGP is used to exchange VPNv4 routes between RRs of different autonomous systems with the
next hops for these routes exchanged between corresponding ASBR routers. Because the RRs in the two autonomous systems are
not directly connected, multihop functionality is required to allow them to establish MP-eBGP peering sessions. The PE router
next-hop addresses for the VPNv4 routes are exchanged between ASBR routers. In this configuration example, the exchange of
these addresses between autonomous systems is established using IPv4 BGP label distribution, which enables the ASBRs to distribute
IPv4 routes with MPLS labels.
Figure 22. Topology for MVPN Inter-AS Support Option C Configuration Example
The table provides information about the topology used for this inter-AS MVPN Option C configuration example.
Table 3. Topology Information for MVPN Inter-AS Support Option C Configuration Example
PE, RR, or ASBR Router
AS Number
Loopback0 Interfaces
Default MDT (PIM-SSM)
PE1A
55
10.254.254.2/32
232.1.1.1
RR1A
55
10.252.252.4/32
232.1.1.1
ASBR1A
55
10.254.254.6/32
232.1.1.1
PE1B
65
10.254.254.8/32
232.1.1.1
RR1B
65
10.252.252.10/32
232.1.1.1
ASBR1B
65
10.254.254.12/32
232.1.1.1
PE1A
!
ip vrf blue
rd 55:1111
mdt default 232.1.1.1
!
ip multicast-routing
ip multicast-routing vrf blue
ip multicast rpf proxy vector
!
.
.
.
!
interface GigabitEthernet0/0
ip vrf forwarding blue
ip pim sparse-mode
!
.
.
.
!
router bgp 55
no bgp default route-target filter
bgp log-neighbor-changes
neighbor 10.252.252.4 remote-as 55
neighbor 10.252.252.4 update-source Loopback0
!
address-family ipv4
neighbor 10.252.252.4 activate
neighbor 10.252.252.4 send-label
no auto-summary
no synchronization
exit-address-family
!
address-family ipv4 mdt
neighbor 10.252.252.4 activate
neighbor 10.252.252.4 send-community extended
exit-address-family
!
address-family vpnv4
neighbor 10.252.252.4 activate
neighbor 10.252.252.4 send-community extended
exit-address-family
!
address-family ipv4 vrf blue
redistribute connected
redistribute static
redistribute rip metric 50
no synchronization
exit-address-family
!
.
.
.
!
ip pim ssm default
!
!
ip vrf blue
rd 55:1111
mdt default 232.1.1.1
!
!
ip multicast-routing
ip multicast-routing vrf blue
ip multicast rpf proxy vector
!
.
.
.
!
interface GigabitEthernet12/0
ip vrf forwarding blue
ip pim sparse-mode
!
.
.
.
!
router bgp 65
no bgp default route-target filter
bgp log-neighbor-changes
neighbor 10.252.252.10 remote-as 65
neighbor 10.252.252.10 update-source Loopback0
!
address-family ipv4
neighbor 10.252.252.10 activate
neighbor 10.252.252.10 send-label
no auto-summary
no synchronization
exit-address-family
!
address-family ipv4 mdt
neighbor 10.252.252.10 activate
neighbor 10.252.252.10 send-community extended
exit-address-family
!
address-family vpnv4
neighbor 10.252.252.10 activate
neighbor 10.252.252.10 send-community extended
exit-address-family
!
address-family ipv4 vrf blue
redistribute connected
redistribute static
redistribute rip metric 50
no synchronization
exit-address-family
!
.
.
.
!
ip pim ssm default
!
The following is sample output from the
showippimmdtbgp command for PE1A and PE2A. The sample output displays information about the BGP advertisement of RDs for MDT default groups.
The output displays the MDT default groups advertised, the RDs and source addresses of sources sending to the MDT default
groups, the BGP router ID of the advertising routers, and the BGP next hop address contained in the advertisements.
PE1A# show ip pim mdt bgp
MDT (Route Distinguisher + IPv4) Router ID Next Hop
MDT group 232.1.1.1
55:1111:10.254.254.8 10.252.252.4 10.254.254.8
PE1B# show ip pim mdt bgp
MDT (Route Distinguisher + IPv4) Router ID Next Hop
MDT group 232.1.1.1
55:1111:10.254.254.2 10.252.252.10 10.254.254.2
The following is sample output from the
showipmrouteproxy command from P1A, P2A, P1B, and P2B. Because P routers learn the RPF Vector from encodings in the PIM join message, PIM is
displayed as the origin under the “Origin” field.
P1A# show ip mroute proxy
(10.254.254.8, 232.1.1.1)
Proxy Assigner Origin Uptime/Expire
10.254.254.6 10.0.2.2 PIM 00:15:37/00:02:57
P2A# show ip mroute proxy
(10.254.254.8, 232.1.1.1)
Proxy Assigner Origin Uptime/Expire
10.254.254.6 10.0.4.3 PIM 00:20:41/00:02:46
P1B# show ip mroute proxy
(10.254.254.2, 232.1.1.1)
Proxy Assigner Origin Uptime/Expire
10.254.254.12 10.0.10.9 PIM 00:29:38/00:02:16
P2B# show ip mroute proxy
(10.254.254.2, 232.1.1.1)
Proxy Assigner Origin Uptime/Expire
10.254.254.12 10.0.12.8 PIM 00:29:58/00:02:09
The following is sample output from the
showipmroute command for PE1A, P1A, P2A, ASBR1A, ASBR1B, P1B, P2B, and PE1B. The sample outputs show the global table for the MDT default
group 232.1.1.1. The output from this command confirms that all three PE routers (PE1A, PE2A, and PE1B) have joined the default
MDT.
PE1A
PE1A# show ip mroute 232.1.1.1
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report,
Z - Multicast Tunnel, z - MDT-data group sender,
Y - Joined MDT-data group, y - Sending to MDT-data group
V - RD & Vector, v - Vector
Outgoing interface flags: H - Hardware switched, A - Assert winner
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(10.254.254.8, 232.1.1.1), 00:12:27/00:02:43, flags: sTIZv
Incoming interface: GigabitEthernet1/0, RPF nbr 10.0.2.3, vector 10.254.254.6
Outgoing interface list:
MVRF blue, Forward/Sparse-Dense, 00:12:27/00:00:00
(10.254.254.2, 232.1.1.1), 00:14:40/00:03:12, flags: sT
Incoming interface: Loopback0, RPF nbr 0.0.0.0
Outgoing interface list:
GigabitEthernet1/0, Forward/Sparse-Dense, 00:12:27/00:03:06
P1A
P1A# show ip mroute 232.1.1.1
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report,
Z - Multicast Tunnel, z - MDT-data group sender,
Y - Joined MDT-data group, y - Sending to MDT-data group
V - RD & Vector, v - Vector
Outgoing interface flags: H - Hardware switched, A - Assert winner
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(10.254.254.2, 232.1.1.1), 00:15:40/00:03:25, flags: sT
Incoming interface: GigabitEthernet1/0, RPF nbr 10.0.2.2
Outgoing interface list:
GigabitEthernet4/0, Forward/Sparse-Dense, 00:15:40/00:03:24
(10.254.254.8, 232.1.1.1), 00:15:40/00:03:25, flags: sTv
Incoming interface: GigabitEthernet4/0, RPF nbr 10.0.4.5, vector 10.254.254.6
Outgoing interface list:
GigabitEthernet1/0, Forward/Sparse-Dense, 00:15:40/00:03:25
P2A
P2A# show ip mroute 232.1.1.1
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report,
Z - Multicast Tunnel, z - MDT-data group sender,
Y - Joined MDT-data group, y - Sending to MDT-data group
V - RD & Vector, v - Vector
Outgoing interface flags: H - Hardware switched, A - Assert winner
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(10.254.254.2, 232.1.1.1), 00:20:43/00:03:15, flags: sT
Incoming interface: GigabitEthernet4/0, RPF nbr 10.0.4.3
Outgoing interface list:
GigabitEthernet5/0, Forward/Sparse-Dense, 00:20:43/00:03:15
(10.254.254.8, 232.1.1.1), 00:20:43/00:03:15, flags: sTv
Incoming interface: GigabitEthernet5/0, RPF nbr 10.0.6.6, vector 10.254.254.6
Outgoing interface list:
GigabitEthernet4/0, Forward/Sparse-Dense, 00:20:43/00:03:14
ASBR1A
ASBR1A# show ip mroute 232.1.1.1
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report,
Z - Multicast Tunnel, z - MDT-data group sender,
Y - Joined MDT-data group, y - Sending to MDT-data group
V - RD & Vector, v - Vector
Outgoing interface flags: H - Hardware switched, A - Assert winner
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(10.254.254.8, 232.1.1.1), 00:20:13/00:03:16, flags: sT
Incoming interface: GigabitEthernet6/0, RPF nbr 10.0.7.12
Outgoing interface list:
GigabitEthernet5/0, Forward/Sparse-Dense, 00:20:13/00:02:46
(10.254.254.2, 232.1.1.1), 00:20:13/00:03:16, flags: sT
Incoming interface: GigabitEthernet5/0, RPF nbr 10.0.6.5
Outgoing interface list:
GigabitEthernet6/0, Forward/Sparse-Dense, 00:20:13/00:02:39
ASBR1B
ASBR1B# show ip mroute 232.1.1.1
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report,
Z - Multicast Tunnel, z - MDT-data group sender,
Y - Joined MDT-data group, y - Sending to MDT-data group
V - RD & Vector, v - Vector
Outgoing interface flags: H - Hardware switched, A - Assert winner
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(10.254.254.8, 232.1.1.1), 00:25:46/00:03:13, flags: sT
Incoming interface: GigabitEthernet7/0, RPF nbr 10.0.8.11
Outgoing interface list:
GigabitEthernet6/0, Forward/Sparse-Dense, 00:25:46/00:03:04
(10.254.254.2, 232.1.1.1), 00:25:46/00:03:13, flags: sT
Incoming interface: GigabitEthernet6/0, RPF nbr 10.0.7.6
Outgoing interface list:
GigabitEthernet7/0, Forward/Sparse-Dense, 00:25:46/00:03:07
P1B
P1B# show ip mroute 232.1.1.1
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report,
Z - Multicast Tunnel, z - MDT-data group sender,
Y - Joined MDT-data group, y - Sending to MDT-data group
V - RD & Vector, v - Vector
Outgoing interface flags: H - Hardware switched, A - Assert winner
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(10.254.254.8, 232.1.1.1), 00:29:41/00:03:17, flags: sT
Incoming interface: GigabitEthernet10/0, RPF nbr 10.0.10.9
Outgoing interface list:
GigabitEthernet7/0, Forward/Sparse-Dense, 00:29:41/00:02:56
(10.254.254.2, 232.1.1.1), 00:29:41/00:03:17, flags: sTv
Incoming interface: GigabitEthernet7/0, RPF nbr 10.0.8.12, vector 10.254.254.12
Outgoing interface list:
GigabitEthernet10/0, Forward/Sparse-Dense, 00:29:41/00:02:44
P2B
P2B# show ip mroute 232.1.1.1
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report,
Z - Multicast Tunnel, z - MDT-data group sender,
Y - Joined MDT-data group, y - Sending to MDT-data group
V - RD & Vector, v - Vector
Outgoing interface flags: H - Hardware switched, A - Assert winner
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(10.254.254.8, 232.1.1.1), 00:30:01/00:03:25, flags: sT
Incoming interface: GigabitEthernet11/0, RPF nbr 10.0.12.8
Outgoing interface list:
GigabitEthernet10/0, Forward/Sparse-Dense, 00:30:01/00:02:30
(10.254.254.2, 232.1.1.1), 00:30:01/00:03:25, flags: sTv
Incoming interface: GigabitEthernet10/0, RPF nbr 10.0.10.11, vector 10.254.254.12
Outgoing interface list:
GigabitEthernet11/0, Forward/Sparse-Dense, 00:30:01/00:02:36
PE1B
PE1B# show ip mroute 232.1.1.1
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report,
Z - Multicast Tunnel, z - MDT-data group sender,
Y - Joined MDT-data group, y - Sending to MDT-data group
V - RD & Vector, v - Vector
Outgoing interface flags: H - Hardware switched, A - Assert winner
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(10.254.254.2, 232.1.1.1), 00:31:22/00:02:55, flags: sTIZv
Incoming interface: GigabitEthernet11/0, RPF nbr 10.0.12.9, vector 10.254.254.12
Outgoing interface list:
MVRF blue, Forward/Sparse-Dense, 00:31:22/00:00:00
(10.254.254.8, 232.1.1.1), 00:33:35/00:03:25, flags: sT
Incoming interface: Loopback0, RPF nbr 0.0.0.0
Outgoing interface list:
GigabitEthernet11/0, Forward/Sparse-Dense, 00:31:22/00:03:22
2 RFC 4364 is the latest RFC standard and obsoletes RFC 2547 (and the later RFC2547bis Internet draft standard).
Technical Assistance
Description
Link
The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and
resolving technical issues with Cisco products and technologies.
To receive security and technical information about your products, you can subscribe to various services, such as the Product
Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds.
Access to most tools on the Cisco Support website requires a Cisco.com user ID and password.
Feature Information for Configuring Multicast VPN Inter-AS Support
The following table provides release information about the feature or features described in this module. This table lists
only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise,
subsequent releases of that software release train also support that feature.
Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco
Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.
Table 4. Feature Information for Configuring Multicast VPN Inter-AS Support
Feature Name
Releases
Feature Information
BGP Multicast Inter-AS VPN
12.0(29)S
12.2(33)SRA
12.2(31)SB2
12.2(33)SXH
12.4(20)T
15.0(1)S
The BGP Multicast Inter-AS VPN feature introduces the IPv4 MDT SAFI in BGP. The MDT SAFI is a transitive multicast capable
connector attribute that is defined as an IPv4 address family in BGP. The MDT SAFI is designed to support inter-AS VPN peering
sessions.
The following commands were introduced or modified by this feature:
address-familyipv4 (BGP),
clearbgpipv4mdt,
showipbgpipv4.
Multicast VPN Inter-AS Support
12.0(30)S
12.2(33)SRA
12.2(31)SB2
12.2(33)SXH
12.4(20)T
15.0(1)S
The Multicast VPN Inter-AS support feature enables MDTs used for MVPNs to span multiple autonomous systems. Benefits include
increased multicast coverage to customers that require multicast to span multiple service providers in an MPLS Layer 3 VPN
service with the flexibility to support all options described in RFC 4364. Additionally, the Multicast VPN Inter-AS Support
feature may be used to consolidate an existing MVPN service with another MVPN service, such as the case with a company merger
or acquisition.
The following commands were introduced or modified by this feature:
ipmulticastrpfproxyvector, and
showipmroute,
showippimneighbor,
showiprpf.
Feedback