IPv6 Destination Guard

The IPv6 Destination Guard feature works with IPv6 neighbor discovery to ensure that the device performs address resolution only for those addresses that are known to be active on the link. It relies on the address glean functionality to populate all destinations active on the link into the binding table and then blocks resolutions before they happen when the destination is not found in the binding table.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

Prerequisites for IPv6 Destination Guard

  • You should be familiar with the IPv6 Neighbor Discovery feature. For information about IPv6 neighbor discovery, see the “Implementing IPv6 Addressing and Basic Connectivity” module.

  • You should be familiar with the IPv6 First-Hop Security Binding Table feature. For information, see the “IPv6 First-Hop Security Binding Table” module.

Information About IPv6 Destination Guard

IPv6 Destination Guard Overview

The IPv6 Destination Guard feature works with IPv6 neighbor discovery to ensure that the device performs address resolution only for those addresses that are known to be active on the link. It relies on the address glean functionality to populate all destinations active on the link into the binding table and then blocks resolutions before they happen when the destination is not found in the binding table.

Prior to filtering incoming routed traffic, the device gleans addresses on the link, by snooping Neighbor Discovery Protocol (NDP) and DHCP messages. When a packet reaches the device and there is not yet an adjacency for the destination or for the next hop, the NDP consults the device binding table to verify that the destination on link or the next-hop have been previously gleaned. If the destination is not found in the binding table, the packet is dropped. Otherwise, neighbor discovery resolution is performed.

How to Configure the IPv6 Destination Guard

Configuring IPv6 Destination Guard

SUMMARY STEPS

    1.    enable

    2.    configure terminal

    3.    ipv6 destination-guard policy policy-name

    4.    enforcement {always | stressed}

    5.    exit

    6.    interface type number

    7.    ipv6 destination-guard attach-policy [policy-name]

    8.    exit

    9.    show ipv6 destination-guard policy [policy-name]


DETAILED STEPS
     Command or ActionPurpose
    Step 1 enable


    Example:
    Device> enable
     

    Enables privileged EXEC mode.

    • Enter your password if prompted.

     
    Step 2 configure terminal


    Example:
    Device# configure terminal
     

    Enters global configuration mode.

     
    Step 3 ipv6 destination-guard policy policy-name


    Example:
    Device(config)# ipv6 destination-guard policy pol1
     

    Defines the destination guard policy name and enters destination-guard configuration mode.

     
    Step 4enforcement {always | stressed}


    Example:
     
Device(config-destguard)# enforcement always
     

    Sets the enforcement level for the target address.

     
    Step 5exit


    Example:
    Device(config-destguard)# exit
     

    Exits destination-guard configuration mode and returns to global configuration mode.

     
    Step 6 interface type number


    Example:
    Device(config)# interface GigabitEthernet 0/0/1
     

    Enters interface configuration mode.

     
    Step 7 ipv6 destination-guard attach-policy [policy-name]


    Example:
    Device(config-if)# ipv6 destination-guard attach-policy pol1
     

    Attaches a destination guard policy to an interface.

     
    Step 8 exit


    Example:
    Device(config-if)# exit
     

    Exits interface configuration mode and returns to privileged EXEC configuration mode.

     
    Step 9 show ipv6 destination-guard policy [policy-name]


    Example:
    Device# show ipv6 destination-guard policy pol1
     

    (Optional) Displays the policy configuration and all interfaces where the policy is applied.

     

    Configuration Examples for IPv6 Destination Guard

    Example: Configuring an IPv6 Destination Guard Policy

    The following example shows how to configure a destination guard policy: 

    Router> enable
Router# configure terminal
Router(config)# interface GigabitEthernet 0/0/1
Router(config-if)# ipv6 destination-guard attach-policy destination

Router# show ipv6 destination-guard policy destination
Destination guard policy Destination: 
  enforcement always
        Target: Gi0/0/1

    Additional References

    Related Documents

    Related Topic

    Document Title

    Cisco IOS commands

    Cisco IOS Master Command List, All Releases

    IPv6 addressing and connectivity

    IPv6 Configuration Guide

    IPv6 commands

    Cisco IOS IPv6 Command Reference

    Cisco IOS IPv6 features

    Cisco IOS IPv6 Feature Mapping

    Technical Assistance

    Description

    Link

    The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.

    http:/​/​www.cisco.com/​cisco/​web/​support/​index.html

    Feature Information for IPv6 Destination Guard

    The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

    Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

    Table 1 Feature Information for IPv6 Destination Guard

    Feature Name

    Releases

    Feature Information

    IPv6 Destination Guard

    15.2(4)S

    15.2(1)E

    15.1(2)SG

    IOS XE 3.6.0E, IOS 15.2(2)E

    15.2(1)SY

    The IPv6 Destination Guard feature blocks data traffic from an unknown source and filters IPv6 traffic based on the destination address.

    The following commands were introduced or modified: enforcement, ipv6 destination-guard attach-policy, ipv6 destination-guard policy, show ipv6 destination-guard policy.