PMIP: Multipath Support on MAG and LMA

The PMIP: Multipath Support on MAG and LMA feature enables Mobile Access Gateway (MAG) to register multiple transport end-points with Local Mobility Anchor (LMA), allowing MAG and LMA to establish multiple tunnels and apply path selection on a flow basis.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

Prerequisites for PMIP: Multipath Support for MAG and LMA

  • Configure UDP in tunnel encapsulation mode on Mobile Access Gateway (MAG) and Local Mobility Anchor (LMA).

  • Configure multipath and run the IP SLA responder.

Information About PMIP: Multipath Support for MAG and LMA

Local Mobility Anchor

Local Mobility Anchor (LMA) is the home agent for a mobile node (MN) in a Proxy Mobile IPv6 (PMIPv6) domain. It is the topological anchor point for MN home network prefixes and manages the binding state of an MN. An LMA has the functional capabilities of a home agent as defined in the Mobile IPv6 base specification (RFC 3775) along with the capabilities required for supporting the PMIPv6 protocol.


Note


Use the dynamic mag learning command to enable LMA to accept Proxy Mobile IPv6 (PMIPv6) signaling messages from any Mobile Access Gateway (MAG) that is not configured locally.


Mobile Access Gateways

Mobile Access Gateway (MAG) performs mobility-related signaling on behalf of the mobile nodes (MN) attached to its access links. MAG is the access router for the MN; that is, MAG is the first-hop router in the localized mobility management infrastructure.

MAG performs the following functions:

  • Obtains an IP address from Local Mobility Anchor (LMA) and assigns it to MN.

  • Retains the IP address of an MN when the MN roams across MAGs.

  • Tunnels traffic from MN to LMA.

Mobile Node

Mobile node (MN) is an IP host and the mobility of the MN is managed by a network. MN can be an IPv4-only node, an IPv6-only node, or a dual-stack node, which is a node with IPv4 and IPv6 protocol stacks. MN is not required to participate in any IP mobility-related signaling for achieving mobility for an IP address or a prefix that is obtained in the Proxy Mobile IPv6 (PMIPv6) domain.

Multipath Support

At any given time, many network paths exists between Local Mobility Anchor (LMA) and Mobile Access Gateway (MAG). The PMIP: Multipath Support on MAG and LMA feature enables MAG to select any one of the paths on priority basis or select all the existing network paths simultaneously to create tunnels to reach LMA. All paths have the same priority when multiple paths are selected.

Mobile Map

Mobile map configuration facilitates application-based routing. More than one mobile map can be configured under the Proxy Mobile IPv6 (PMIPv6) domain, however, at a given point of time, only one mobile map is active at Mobile Access Gateway (MAG) and Local Mobility Anchor (LMA). The mobile map and its entries are configured or modified when no bindings are available.

Logical Mobile Node

Logical Mobile Node (LMN) is a logical entity that represents a mobile node (MN) that is hosted on one of the interfaces of Mobile Access Gateway (MAG) device. LMN has Network Access Indicator (NAI) similar to MN. One or more networks can be associated with each LMN through the interfaces designated as mobile network interfaces. LMN on mobile network receives an IP address from a DHCP server that runs on MAG, unlike a mobile node whose address is assigned by Local Mobility Anchor (LMA).

Multipath Management

The PMIPv6 Mutipath Management feature enables PMIPv6 to choose from multiple available links which have different access technologies. Available path is constantly monitored using PMIPv6 heartbeat which is a special type of PMIPv6 packet. Link preferences can be assigned to various types of traffic using mobile maps.

Hybrid-Access Service

Hybrid-access service is a multipath management solution, which provides mobility service under MAG. PMIPv6 hybrid-access service is an independent function that manages application profiles, captures and stores link performance statistics, and programs the PMIPv6 data plane based on the application requirements (HTTP, SSH, Telnet, and video).


Note


PMIPv6 hybrid-access service has no interference with the core PMIPv6 functionality.


MAG to MAG Traffic Blocking on the PMIPv6 LMA

To prevent communication between PMIPv6 clients such as, mobile nodes (MNs), or entire mobile networks, that are connected to the same Local Mobility Anchor (LMA), the inter-MAG tunnel traffic is blocked by applying access control list (ACL) on the PMIPv6 tunnels. To enable the blockage of inter-MAG tunnel traffic, the prefixes of all the PMIPv6 addresses mentioned in the address pool configured on LMA, must be entered in the ACL.

How to Configure PMIP: Multipath Support for MAG and LMA

Configuring PMIP: Multipath Support for MAG and LMA

Configuring UDP Encapsulation for a PMIPv6 Domain

SUMMARY STEPS

    1.    enable

    2.    configure terminal

    3.    ipv6 mobile pmipv6-domain domain-name

    4.    encap udptunnel

    5.    end


DETAILED STEPS
     Command or ActionPurpose
    Step 1 enable


    Example:
    Device> enable
     

    Enables privileged EXEC mode.

    • Enter your password if prompted.

     
    Step 2 configure terminal


    Example:
    Device# configure terminal
     

    Enters global configuration mode.

     
    Step 3 ipv6 mobile pmipv6-domain domain-name


    Example:
    Device(config)# ipv6 mobile pmipv6-domain dn1
     

    Creates a PMIPv6 domain and enters PMIPv6 domain configuration mode.

     
    Step 4 encap udptunnel


    Example:
    Device(config-ipv6-pmipv6-domain)# encap udptunnel
     

    Configures the tunnel encapsulation mode type between Mobile Access Gateway (MAG) and Local Mobility Anchor (LMA).

     
    Step 5 end


    Example:
    Device(onfig-ipv6-pmipv6-domain)# end
     

    Exits PMIPv6 domain configuration mode and returns to privileged EXEC mode.

     

    Configuring Roaming Interface


    Note


    Perform this task when configuring multipath for MAG.


    SUMMARY STEPS

      1.    enable

      2.    configure terminal

      3.    ipv6 mobile pmipv6-mag mag-id domain domain-name

      4.    address dynamic

      5.    roaming interface type number

      6.    exit


    DETAILED STEPS
       Command or ActionPurpose
      Step 1 enable


      Example:
      Device> enable
       

      Enables privileged EXEC mode.

      • Enter your password if prompted.

       
      Step 2 configure terminal


      Example:
      Device# configure terminal
       

      Enters global configuration mode.

       
      Step 3 ipv6 mobile pmipv6-mag mag-id domain domain-name


      Example:
      Device(config)# ipv6 mobile pmipv6-mag mag1 domain dn1
       

      Enables MAG service on a device, configures the PMIPv6 domain for MAG, and enters MAG configuration mode.

       
      Step 4 address dynamic


      Example:
      Device(config-ipv6-pmipv6-mag)# address dynamic
       

      Configures dynamic address for MAG and enters MAG dynamic address configuration mode.

       
      Step 5 roaming interface type number


      Example:
      Device(config-ipv6-pmipv6-mag-addr-dyn)# roaming interface Ethernet 0/0 
       

      Specifies an interface as a roaming interface on MAG.

       
      Step 6 exit


      Example:
      Device(config-ipv6-pmipv6-mag-addr-dyn)# exit
       

      Exits MAG dynamic address configuration mode and returns to privileged EXEC mode.

       

      Configuring Multipath under LMA and MAG Configurations

      SUMMARY STEPS

        1.    enable

        2.    configure terminal

        3.    ipv6 mobile pmipv6-lma lma-id domain domain-name

        4.    multipath

        5.    exit

        6.    ipv6 mobile pmipv6-mag mag1 domain dn1

        7.    multipath

        8.    exit


      DETAILED STEPS
         Command or ActionPurpose
        Step 1 enable


        Example:
        Device> enable
         

        Enables privileged EXEC mode.

        • Enter your password if prompted.

         
        Step 2 configure terminal


        Example:
        Device# configure terminal
         

        Enters global configuration mode.

         
        Step 3 ipv6 mobile pmipv6-lma lma-id domain domain-name


        Example:
        Device(config)# ipv6 mobile pmipv6-lma lma1 domain dn1
         

        Enables LMA service on the device, configures the PMIPv6 domain for Local Mobility Anchor (LMA), and enters LMA configuration mode.

         
        Step 4 multipath


        Example:
        Device(config-ipv6-pmipv6-lma)# multipath
         

        Enables multipath support on LMA.

         
        Step 5 exit


        Example:
        Device(config-ipv6-pmipv6-lma)# exit
         

        Exits LMA configuration mode and enters global configuration mode.

         
        Step 6 ipv6 mobile pmipv6-mag mag1 domain dn1


        Example:
        Device(config)# ipv6 mobile pmipv6-mag mag1 domain dn1
         

        Enables MAG service on a device, configures the PMIPv6 domain for MAG, and enters MAG configuration mode.

         
        Step 7 multipath


        Example:
        Device(config-ipv6-pmipv6-mag)# multipath
         

        Enables multipath support on MAG.

         
        Step 8 exit


        Example:
        Device(config-ipv6-pmipv6-mag)# exit
         

        Exits MAG configuration mode and returns to global configuration mode.

         

        Configuring Mobile Map Support on LMA

        Configuring Access Lists in LMA

        SUMMARY STEPS

          1.    enable

          2.    configure terminal

          3.    ip access-list extended access-list-name

          4.    permit protocol any any

          5.    exit

          6.    ip access-list extended access-list-name

          7.    permit protocol any any

          8.    exit

          9.    ip access-list extended access-list-name

          10.    permit protocol any any

          11.    exit

          12.    ip access-list extended access-list-name

          13.    permit ip any destination-address destination-wildcard

          14.    end


        DETAILED STEPS
           Command or ActionPurpose
          Step 1 enable


          Example:
          Device> enable
           

          Enables privileged EXEC mode.

          • Enter your password if prompted.

           
          Step 2 configure terminal


          Example:
          Device# configure terminal
           

          Enters global configuration mode.

           
          Step 3 ip access-list extended access-list-name


          Example:
          Device(config)# ip access-list extended tcp
           

          Configures an extended named ACL specific to TCP.

           
          Step 4 permit protocol any any


          Example:
          Device(config-ext-nacl)# permit tcp any any 
           

          Sets conditions in named IP lists that permit packets.

           
          Step 5 exit


          Example:
          Device(config-ext-nacl)# exit
           

          Exits extended-ACL configuration mode and returns to global configuration mode.

           
          Step 6 ip access-list extended access-list-name


          Example:
          Device(config)# ip access-list extended icmp
           

          Configures an extended named ACL specific to Internet Control Message Protocol (ICMP).

           
          Step 7 permit protocol any any


          Example:
          Device(config-ext-nacl)# permit icmp any any 
           

          Sets conditions in named IP lists that permit packets.

           
          Step 8 exit


          Example:
          Device(config-ext-nacl)# exit
           

          Exits extended-ACL configuration mode and returns to global configuration mode.

           
          Step 9 ip access-list extended access-list-name


          Example:
          Device(config)# ip access-list extended udp
           

          Configures an extended named ACL specific to UDP.

           
          Step 10 permit protocol any any


          Example:
          Device(config-ext-nacl)# permit udp any any
           

          Sets conditions in named IP lists that permit packets.

           
          Step 11 exit


          Example:
          Device(config-ext-nacl)# exit
           

          Exits extended-ACL configuration mode and returns to global configuration mode.

           
          Step 12 ip access-list extended access-list-name


          Example:
          Device(config)# ip access-list extended LB010ACL
           

          Configures an extended named ACL.

           
          Step 13 permit ip any destination-address destination-wildcard


          Example:
          Device(config-ext-nacl)# permit ip any 10.255.224.0 0.0.0.255
           

          Sets conditions in named IP lists that permit packets.

           
          Step 14 end


          Example:
          Device(config-ext-nacl)# end
           

          Exits extended-ACL configuration mode and returns to privileged EXEC mode.

           

          Configuring Mobile Maps under the PMIPv6 domain

          SUMMARY STEPS

            1.    enable

            2.    configure terminal

            3.    ipv6 mobile pmipv6-domain domain-name terminal

            4.    mobile-map map-name sequence-number

            5.    match access-list acl-list-name

            6.    set link-type link-name1[ link-name2] [link-name2] null

            7.    exit

            8.    mobile-map map-name sequence-number

            9.    match access-list acl-list-name

            10.    set link-type link-name1 null

            11.    end


          DETAILED STEPS
             Command or ActionPurpose
            Step 1 enable


            Example:
            Device> enable
             

            Enables privileged EXEC mode.

            • Enter your password if prompted.

             
            Step 2 configure terminal


            Example:
            Device# configure terminal
             

            Enters global configuration mode.

             
            Step 3 ipv6 mobile pmipv6-domain domain-name terminal


            Example:
            Device(config)# ipv6 mobile pmipv6-domain dn1
             

            Creates a PMIP domain and enters PMIPv6 domain configuration mode.

             
            Step 4 mobile-map map-name sequence-number


            Example:
            Device(config-ipv6-pmipv6-domain)# mobile-map mobilemap1 10
             

            Configures a mobile map for the PMIPv6 domain and enters mobile-map configuration mode.

             
            Step 5 match access-list acl-list-name


            Example:
            Device(config-ipv6-pmipv6-domain-mobile-map)# match access-list LB010ACL
             

            Specifies an access list (ACL) name.

             
            Step 6 set link-type link-name1[ link-name2] [link-name2] null


            Example:
            Device(config-ipv6-pmipv6-domain-mobile-map)# set link-type lte_intf 3g_intf wifi_intf null
             

            Specifies the link type for a match clause.

             
            Step 7 exit


            Example:
            Device(config-ipv6-pmipv6-domain-mobile-map)# exit
             

            Exits mobile-map configuration mode and enters global configuration mode.

             
            Step 8 mobile-map map-name sequence-number


            Example:
            Device(config-ipv6-pmipv6-domain)# mobile-map mobilemap1 20
             

            Configures a mobile map for a PMIPv6 domain and enters mobile-map configuration mode.

             
            Step 9 match access-list acl-list-name


            Example:
            Device(config-ipv6-pmipv6-domain-mobile-map)# match access-list icmp
             

            Specifies an access-list (ACL) name.

             
            Step 10 set link-type link-name1 null


            Example:
            Device(config-ipv6-pmipv6-domain-mobile-map)# set link-type 3g_intf_lte_intf null
             

            Specifies the link type for a match clause.

             
            Step 11 end


            Example:
            Device(config-ipv6-pmipv6-domain-mobile-map)# end
             

            Exits mobile-map configuration mode and returns to privileged EXEC mode.

             

            Configuring a Mobile Map under LMA Configuration and Applying it on an Interface

            SUMMARY STEPS

              1.    enable

              2.    configure terminal

              3.    ipv6 mobile pmipv6-lma lma-id domain domain-name

              4.    mobile-map map-name

              5.    interface type number

              6.    end


            DETAILED STEPS
               Command or ActionPurpose
              Step 1 enable


              Example:
              Device> enable
               

              Enables privileged EXEC mode.

              • Enter your password if prompted.

               
              Step 2 configure terminal


              Example:
              Device# configure terminal
               

              Enters global configuration mode.

               
              Step 3 ipv6 mobile pmipv6-lma lma-id domain domain-name


              Example:
              Device(config)# ipv6 mobile pmipv6-lma lma1 domain dn1
               

              Enables LMA service on the device, configures the PMIP domain for LMA, and enters LMA configuration mode.

               
              Step 4 mobile-map map-name


              Example:
              Device(config-ipv6-pmipv6-lma)# mobile-map mobilemap1
               

              Configures a mobile map for the PMIPv6 domain and enters mobile-map configuration mode.

              Note   

              If you modify one or more access-list entries, for the modified access list to be applied, you must unconfigure the mobile map from LMA configuration and reconfigure it.

               
              Step 5 interface type number


              Example:
              Device(config-ipv6-pmipv6-lma)# interface gigabitethernet 0/0/0
               

              Enables an interface for the mobile map.

               
              Step 6 end


              Example:
              Device(config-ipv6-pmipv6-lma)# end
               

              Exits mobile-map configuration mode and returns to privileged EXEC mode.

               

              Configuring the MTU to be Applied on the PMIPv6 Tunnel

              SUMMARY STEPS

                1.    enable

                2.    configure terminal

                3.    ipv6 mobile pmipv6-lma lma-id domain domain-name

                4.    tunnel mtu mtu-size

                5.    end


              DETAILED STEPS
                 Command or ActionPurpose
                Step 1 enable


                Example:
                Device> enable
                 

                Enables privileged EXEC mode.

                • Enter your password if prompted.

                 
                Step 2 configure terminal


                Example:
                Device# configure terminal
                 

                Enters global configuration mode.

                 
                Step 3 ipv6 mobile pmipv6-lma lma-id domain domain-name


                Example:
                Device(config)# ipv6 mobile pmipv6-lma lma1 domain dn1
                 

                Enables LMA service on the device, configures the PMIP domain for LMA, and enters LMA configuration mode.

                 
                Step 4 tunnel mtu mtu-size


                Example:
                Device(config-ipv6-pmipv6-lma)# tunnel mtu 1360
                 

                Configures a maximum transmission unit (MTU) on a PMIPv6 tunnel.

                 
                Step 5 end


                Example:
                Device(config-ipv6-pmipv6-lma)# end
                 

                Exits LMA configuration mode and returns to privileged EXEC mode.

                 

                Applying an ACL on the PMIPv6 Tunnel

                SUMMARY STEPS

                  1.    enable

                  2.    configure terminal

                  3.    ip access-list extended access-list-name

                  4.    deny protocol host addr any

                  5.    permit protocol any any

                  6.    exit

                  7.    ipv6 mobile pmipv6-mag mag-id domain domain-name

                  8.    tunnel acl acl-list-name

                  9.    end


                DETAILED STEPS
                   Command or ActionPurpose
                  Step 1 enable


                  Example:
                  Device> enable
                   

                  Enables privileged EXEC mode.

                  • Enter your password if prompted.

                   
                  Step 2 configure terminal


                  Example:
                  Device# configure terminal
                   

                  Enters global configuration mode.

                   
                  Step 3 ip access-list extended access-list-name


                  Example:
                  Device(config)# ip access-list extended acl1
                   

                  Defines an IP access list by name and enters the extended ACL configuration mode.

                   
                  Step 4 deny protocol host addr any


                  Example:
                  Device(config-ext-nacl)# deny ip host 10.2.2.2 any
                   

                  Sets conditions in a named IP access list that will deny packets.

                   
                  Step 5 permit protocol any any


                  Example:
                  Device(config-ext-nacl)# permit ip any any
                   

                  Sets conditions to allow a packet to pass a named IP access list.

                   
                  Step 6 exit


                  Example:
                  Device(config-ext-nacl)# exit
                   

                  Exits the extended ACL configuration mode and returns to the global configuration mode.

                   
                  Step 7 ipv6 mobile pmipv6-mag mag-id domain domain-name


                  Example:
                  Device(config)# ipv6 mobile pmipv6-lma mag1 domain dn1 
                   

                  Enables MAG service on the device, configures the PMIP domain for LMA, and enters MAG configuration mode.

                   
                  Step 8 tunnel acl acl-list-name


                  Example:
                  Device(config-ipv6-pmipv6-lma)# tunnel acl acl1
                   

                  Specifies an ACL to be applied on the PMIPv6 tunnel in an LMA.

                   
                  Step 9 end


                  Example:
                  Device(config-ipv6-pmipv6-lma)# end
                   

                  Exits LMA configuration mode and returns to privileged EXEC mode.

                   

                  Configuring Multiple Mobile Network IPv4 or IPv6 Address Pools for a Network Under LMA Configuration

                  SUMMARY STEPS

                    1.    enable

                    2.    configure terminal

                    3.    ipv6 mobile pmipv6-lma lma-id domain domain-name

                    4.    network name

                    5.    Do one of the following:

                    • mobile-network pool address pool-prefix pool-prefix network-prefix network-prefix
                    • mobile-network v6pool address pool-prefix pool-prefix network-prefix network-prefix

                    6.    Do one of the following:

                    • mobile-network pool address pool-prefix pool-prefix network-prefix network-prefix
                    • mobile-network v6pool address pool-prefix pool-prefix network-prefix network-prefix

                    7.    end


                  DETAILED STEPS
                     Command or ActionPurpose
                    Step 1 enable


                    Example:
                    Device> enable
                     

                    Enables privileged EXEC mode.

                    • Enter your password if prompted.

                     
                    Step 2 configure terminal


                    Example:
                    Device# configure terminal
                     

                    Enters global configuration mode.

                     
                    Step 3 ipv6 mobile pmipv6-lma lma-id domain domain-name


                    Example:
                    Device(config)# ipv6 mobile pmipv6-lma lma1 domain dn1
                     

                    Enables LMA service on the device, configures the PMIP domain for LMA, and enters LMA configuration mode.

                     
                    Step 4 network name


                    Example:
                    Device(config-ipv6-pmipv6-lma)# network name
                     

                    Specifies mobile address pools, from which a mobile network prefix is allocated to a logical mobile node (LMN) and enters LMA-network configuration mode.

                     
                    Step 5Do one of the following:
                    • mobile-network pool address pool-prefix pool-prefix network-prefix network-prefix
                    • mobile-network v6pool address pool-prefix pool-prefix network-prefix network-prefix


                    Example:
                    Device(config)# mobile-network pool 10.20.2.1 pool-prefix 24 network-prefix 30


                    Example:
                    Device(config)# mobile-network pool 2001:DB8::1 pool-prefix 48  pool-prefix 48 network-prefix 30
                     

                    Associates a network, to which an IPv4 or IPv6 pool can be configured, with LMA.

                     
                    Step 6Do one of the following:
                    • mobile-network pool address pool-prefix pool-prefix network-prefix network-prefix
                    • mobile-network v6pool address pool-prefix pool-prefix network-prefix network-prefix


                    Example:
                    Device(config)# mobile-network pool 10.20.2.2 pool-prefix 24 network-prefix 30


                    Example:
                    Device(config)# mobile-network pool 2001:DB8::2 pool-prefix 64 pool-prefix 48 network-prefix 30
                     

                    Associates a network, to which an IPv4 or IPv6 pool can be configured, with LMA.

                     
                    Step 7 end


                    Example:
                    Device(config-ipv6-pmipv6lma-network)# end
                     

                    Exits LMA-network configuration mode and returns to privileged EXEC mode.

                     

                    Configuring Heartbeat under LMA Configuration

                    SUMMARY STEPS

                      1.    enable

                      2.    configure terminal

                      3.    ipv6 mobile pmipv6-lma lma-id domain domain-name

                      4.    heartbeat [interval interval retries retries [label label] natreboot]]

                      5.    end


                    DETAILED STEPS
                       Command or ActionPurpose
                      Step 1 enable


                      Example:
                      Device> enable
                       

                      Enables privileged EXEC mode.

                      • Enter your password if prompted.

                       
                      Step 2 configure terminal


                      Example:
                      Device# configure terminal
                       

                      Enters global configuration mode.

                       
                      Step 3 ipv6 mobile pmipv6-lma lma-id domain domain-name


                      Example:
                      Device(config)# ipv6 mobile pmipv6-lma lma1 domain dn1
                       

                      Enables LMA service on the device, configures the PMIP domain for LMA, and enters LMA configuration mode.

                       
                      Step 4 heartbeat [interval interval retries retries [label label] natreboot]]


                      Example:
                      Device(config-ipv6-pmipv6-lma)# heartbeat interval 300 retries 2 label label1 natreboot
                       

                      Configures heartbeat detection between MAG and LMA.

                       
                      Step 5 end


                      Example:
                      Device(config-ipv6-pmipv6-lma)# end
                       

                      Exits LMA configuration mode and returns to privileged EXEC mode.

                       

                      Configuring Multipath Management

                      Configuring Multipath Management on LMA

                      SUMMARY STEPS

                        1.    enable

                        2.    configure terminal

                        3.    ipv6 mobile pmipv6-domain domain-name

                        4.    mobile-map map-name sequence-number

                        5.    match access-list access list name

                        6.    set link-type link-type

                        7.    ipv6 mobile pmipv6-lma lma-id domain domain-name

                        8.    address ipv4 ipv4-address

                        9.    heartbeat [interval interval retries retries]

                        10.    bce maximum number

                        11.    default profile profile-name

                        12.    dynamic mag learning

                        13.    multipath

                        14.    mobile-map map-name sequence-number

                        15.    tunnel mtu mtu-size

                        16.    interface interface-type

                        17.    network network-name

                        18.    Do one of the following:

                        • pool ipv4 pool-name pfxlen number
                        • mobile-network v4pool address pool-prefix pool-prefix network-prefix network-prefix

                        19.    end


                      DETAILED STEPS
                         Command or ActionPurpose
                        Step 1enable


                        Example:
                        Device> enable
                         

                        Enables privileged EXEC mode.

                        • Enter your password if prompted.
                         
                        Step 2configure terminal


                        Example:
                        Device# configure terminal
                         

                        Enters global configuration mode.

                         
                        Step 3ipv6 mobile pmipv6-domain domain-name


                        Example:
                        Device(config)# ipv6 mobile pmipv6-domain D1
                         

                        Creates the PMIP domain and enters PMIP domain configuration mode.

                         
                        Step 4mobile-map map-name sequence-number


                        Example:
                        Device (config-ipv6-pmipv6-domain)# mobile-map MAP1 12
                         

                        Configures a mobile map for the PMIPv6 domain and enters mobile-map configuration mode.

                        • The range is from 1 to 255.
                         
                        Step 5match access-list access list name


                        Example:
                        Device (config-ipv6-pmipv6-domain-mobile-map)# match access-list voice
                         

                        Specifies the access list that identifies an application.

                         
                        Step 6set link-type link-type


                        Example:
                        Device (config-ipv6-pmipv6-domain-mobile-map)# set link-type lte_intf 3g_intf
                         

                        Sets link preferences for the application.

                         
                        Step 7ipv6 mobile pmipv6-lma lma-id domain domain-name


                        Example:
                        Device (config-ipv6-pmipv6-domain-mobile-map)# ipv6 mobile pmipv6-lma LMA1 domain D1
                         

                        Enables LMA service on the device, configures the PMIP domain for LMA, and enters LMA configuration mode.

                         
                        Step 8address ipv4 ipv4-address


                        Example:
                        Device (config-ipv6-pmipv6-lma)# address ipv4 9.9.9.1
                         

                        Configures an IPv4 address for LMA.

                         
                        Step 9heartbeat [interval interval retries retries]


                        Example:
                        Device (config-ipv6-pmipv6-lma)# heartbeat interval 15 retries 1
                         

                        Configures heartbeat.

                         
                        Step 10bce maximum number


                        Example:
                        Device (config-ipv6-pmipv6-lma)# bce maximum 128000
                         
                        Configures the maximum number of binding cache entries (BCEs) or bindings that LMA can support.
                        Note    Bindings represent a mobile node session.
                         
                        Step 11default profile profile-name


                        Example:
                        Device (config-ipv6-pmipv6-lma)# default profile regularmn
                         

                        Configures the default profile for mobile nodes.

                         
                        Step 12dynamic mag learning


                        Example:
                        Device (config-ipv6-pmipv6-lma)# dynamic mag learning
                         

                        Enables LMA to accept PMIPv6 signaling messages from any MAG that is not configured locally.

                         
                        Step 13multipath


                        Example:
                        Device (config-ipv6-pmipv6-lma)# multipath
                         

                        Enables multipath support on LMA.

                         
                        Step 14mobile-map map-name sequence-number


                        Example:
                        Device (config-ipv6-pmipv6-lma)# mobile-map MAP1
                         

                        Configures a mobile map for the PMIPv6 domain and enters mobile-map configuration mode.

                         
                        Step 15tunnel mtu mtu-size


                        Example:
                        Device (config-ipv6-pmipv6-lma)# tunnel mtu 1360
                         

                        Configures a maximum transmission unit (MTU) on a PMIPv6 tunnel.

                         
                        Step 16interface interface-type


                        Example:
                        Device (config-ipv6-pmipv6-lma)# interface Ethernet 0/2
                         

                        Configures an egress interface for LMA.

                         
                        Step 17network network-name


                        Example:
                        Device (config-ipv6-pmipv6-lma)# network net1
                         

                        Specifies mobile address pools, from which a mobile network prefix is allocated to a Logical Mobile Node (LMN) and enters LMA-network configuration mode.

                         
                        Step 18Do one of the following:
                        • pool ipv4 pool-name pfxlen number
                        • mobile-network v4pool address pool-prefix pool-prefix network-prefix network-prefix


                        Example:
                        Device (config-ipv6-pmipv6lma-network)# pool ipv4 v4pool pfxlen 24


                        Example:
                        Device (config-ipv6-pmipv6lma-network)# mobile-network pool 10.0.0.1 pool-prefix 24 network-prefix 30
                         

                        Specifies an IPv4 address pool from which a home address is allocated to the MN subscriber and configures IPv4 pool for mobile networks or mobile nodes.

                         
                        Step 19end


                        Example:
                        Device (config-ipv6-pmipv6lma-network)# end
                         

                        Exits LMA configuration mode and returns to privileged EXEC mode.

                         

                        Configuring Multipath Management on MAG

                        SUMMARY STEPS

                          1.    enable

                          2.    configure terminal

                          3.    ipv6 mobile pmipv6-domain domain-name

                          4.    mobile-map map-name sequence-number

                          5.    match access-list access-list name

                          6.    traffic-profile profile-name

                          7.    ipv6 mobile pmipv6-mag mag-id domain domain-name

                          8.    address dynamic

                          9.    roaming interface type number priority interface priority egress-att interface-attribute user assigned labels

                          10.    exit

                          11.    heartbeat [interval interval retries retries]

                          12.    bce maximum number

                          13.    multipath

                          14.    mobile-map map-name sequence-number

                          15.    tunnel mtu mtu-size

                          16.    interface interface-type

                          17.    lma lma-id domain-name

                          18.    mobility-service hybrid-access

                          19.    profile-definition profile-name

                          20.    jitter value

                          21.    rtt value

                          22.    packet-loss value

                          23.    end


                        DETAILED STEPS
                           Command or ActionPurpose
                          Step 1enable


                          Example:
                          Device> enable
                           

                          Enables privileged EXEC mode.

                          • Enter your password if prompted.
                           
                          Step 2configure terminal


                          Example:
                          Device# configure terminal
                           

                          Enters global configuration mode.

                           
                          Step 3ipv6 mobile pmipv6-domain domain-name


                          Example:
                          Device(config)# ipv6 mobile pmipv6-domain D1
                           

                          Creates the PMIP domain and enters PMIP domain configuration mode.

                           
                          Step 4mobile-map map-name sequence-number


                          Example:
                          Device (config-ipv6-pmipv6-domain)# mobile-map MAP1 12
                           

                          Configures a mobile map for the PMIPv6 domain and enters mobile-map configuration mode.

                          • The range is from 1 to 255.
                           
                          Step 5match access-list access-list name


                          Example:
                          Device (config-ipv6-pmipv6-domain-mobile-map)# match access-list voice
                           

                          Specifies an ACL that identifies an application such as HTTP, SSH, Telnet, and video.

                           
                          Step 6traffic-profile profile-name


                          Example:
                          Device (config-ipv6-pmipv6-domain-mobile-map)# traffic-profile haccess-voice
                           

                          Specifies a hybrid access profile where the performance requirements have been defined.

                           
                          Step 7ipv6 mobile pmipv6-mag mag-id domain domain-name


                          Example:
                          Device (config-ipv6-pmipv6-domain-mobile-map)# ipv6 mobile pmipv6-mag MAG1 domain D1
                           

                          Enables MAG service on the device, configures the PMIP domain for MAG, and enters MAG configuration mode.

                           
                          Step 8address dynamic


                          Example:
                          Device (config-ipv6-pmipv6-mag)# address dynamic
                           

                          Configures dynamic address for MAG and enters MAG dynamic address configuration mode.

                           
                          Step 9roaming interface type number priority interface priority egress-att interface-attribute user assigned labels


                          Example:
                          Device (config-ipv6-pmipv6-mag-addr-dyn)# roaming interface Ethernet1/0 priority 1 egress-att LTE label lte_intf


                          Example:
                          Device (config-ipv6-pmipv6-mag-addr-dyn)# roaming interface Ethernet1/1 priority 2 egress-att 3G label 3g_intf
                           

                          Specifies a roaming interface and priority on MAG.

                           
                          Step 10exit


                          Example:
                          Device (config-ipv6-pmipv6-mag-addr-dyn)# exit
                           

                          Enters MAG dynamic address configuration mode and returns to privileged EXEC mode.

                           
                          Step 11heartbeat [interval interval retries retries]


                          Example:
                          Device (config-ipv6-pmipv6-mag)# heartbeat interval 15 retries 1
                           

                          Configures heartbeat.

                           
                          Step 12bce maximum number


                          Example:
                          Device (config-ipv6-pmipv6-mag)# bce maximum 128000
                           

                          Configures the maximum number of binding cache entries (BCEs) or bindings that MAG can support.

                           
                          Step 13multipath


                          Example:
                          Device (config-ipv6-pmipv6-mag)# multipath
                           

                          Enables multipath support on MAG.

                           
                          Step 14mobile-map map-name sequence-number


                          Example:
                          Device (config-ipv6-pmipv6-mag)# mobile-map MAP1
                           

                          Configures a mobile map for the PMIPv6 domain and enters mobile-map configuration mode.

                           
                          Step 15tunnel mtu mtu-size


                          Example:
                          Device (config-ipv6-pmipv6-mag)# tunnel mtu 1360
                           

                          Configures a maximum transmission unit (MTU) on a PMIPv6 tunnel.

                           
                          Step 16interface interface-type


                          Example:
                          Device (config-ipv6-pmipv6-mag)# interface Ethernet 0/2
                           

                          Configures an egress interface for MAG.

                           
                          Step 17lma lma-id domain-name


                          Example:
                          Device(config-ipv6-pmipv6- mag)# lma LMA1 D1
                           

                          Enables LMA service on the device, configures the PMIP domain for LMA, and enters LMA configuration mode.

                           
                          Step 18mobility-service hybrid-access


                          Example:
                          Device (config-ipv6-pmipv6-mag)# mobility-service hybrid-access
                           

                          Configures hybrid-access service.

                           
                          Step 19profile-definition profile-name


                          Example:
                          Device (config-ipv6-pmipv6-mag-haccess-svc)# profile-definition haccess-voice
                           

                          Defines a traffic profile.

                           
                          Step 20jitter value


                          Example:
                          Device (config-ipv6-pmipv6-mag-haccess-profile-def-svc)# jitter 50
                           

                          Configures the jitter value, in milliseconds.

                           
                          Step 21rtt value


                          Example:
                          Device (config-ipv6-pmipv6-mag-haccess-profile-def-svc)# rtt 100
                           

                          Configures the Round Trip Time (RTT) value, in milliseconds.

                           
                          Step 22packet-loss value


                          Example:
                          Device (config-ipv6-pmipv6-mag-haccess-profile-def-svc)# packet-loss 2
                           

                          Configures the packet loss value, in percentage.

                           
                          Step 23end


                          Example:
                          Device (config-ipv6-pmipv6-mag-haccess-profile-def-svc)# end
                           

                          Exits MAG configuration mode and returns to privileged EXEC mode.

                           

                          Configuration Examples for PMIPv6 Multipath Support for MAG and LMA

                          Example: Configuring Multipath on LMA

                          Example: Configuring UDP Encapsulation under PMIPv6 Domain

                          Device> enable
                          Device# configuration terminal
                          Device(config) ipv6 mobile pmipv6-domain D1
                          Device(config-ipv6-pmipv6-domain)# encap udptunnel
                          Device(config-ipv6-pmipv6-domain)# end
                          

                          Example: Configuring Roaming Interface


                          Note


                          This example is applicable when configuring multipath for MAG.


                          Device> enable
                          Device# configuration terminal
                          Device(config) ipv6 mobile pmipv6-ma mag1 domain D1
                          Device(config-ipv6-pmipv6-mag) address dynamic
                          Device(config-ipv6-pmipv6-mag-addr-dyn)# roaming interface Ethernet 0/0 
                          Device(config-ipv6-pmipv6-mag-addr-dyn)# end
                          

                          Example: Configuring PMIP: Multipath Support on LMA

                          Device> enable
                          Device# configuration terminal
                          Device(config) ipv6 mobile pmipv6-lma LMA1 domain D1
                          Device(config-ipv6-pmipv6-lma)# multipath
                          Device(config-ipv6-pmipv6-lma)# end
                          

                          Example: Configuring Mobile Map on an LMA

                          Example: Configuring Access List on an LMA

                          Device> enable
                          Device# configuration terminal
                          Device(config)# ip access-list extended tcp 
                          Device(config-ext-nacl)# permit tcp any any 
                          Device(config-ext-nacl)# exit
                          Device(config)# ip access-list extended icmp
                          Device(config-ext-nacl)# permit icmp any any
                          Device(config-ext-nacl)# exit
                          Device(config)# ip access-list extended udp
                          Device(config-ext-nacl)# permit udp any any 
                          Device(config-ext-nacl)# exit
                          Device(config)# ip access-list extended LB010ACL
                          Device(config-ext-nacl)# permit ip any 10.255.224.0 0.0.0.255
                          Device(config-ext-nacl)# end

                          Example: Applying an ACL on the PMIPv6 Tunnel

                          Device> enable
                          Device# configure terminal
                          Device(config)# ip access-list extended acl1
                          Device(config-ext-nacl)# deny ip host 10.2.2.2 any
                          Device(config)# permit ip any any
                          Device(config)# ipv6 mobile pmipv6-lma lma1 domain dn1 
                          Device(config-ipv6-pmipv6-lma)# tunnel acl acl1
                          Device(config-ipv6-pmipv6-lma)# end

                          Example: Configuring mobile maps under the PMIPv6 domain

                          Device> enable
                          Device# configure terminal
                          Device(config)#  ipv6 mobile pmipv6-domain dn1
                          Device(config-ipv6-pmipv6-domain)# mobile-map mobilemap1 10
                          Device(config-ipv6-pmipv6-domain-mobile-map)# match access-list LB010ACL
                          Device(config-ipv6-pmipv6-domain-mobile-map)# set link-type lte_intf_3g_intf null
                          Device(config-ipv6-pmipv6-domain-mobile-map)# exit 
                          Device(config-ipv6-pmipv6-domain)# mobile-map mobilemap1 20
                          Device(config-ipv6-pmipv6-domain-mobile-map)# match access-list icmp
                          Device(config-ipv6-pmipv6-domain-mobile-map)# set link-type lte_intf 3g_intf wifi_intf null
                          Device(config-ipv6-pmipv6-domain-mobile-map)# end
                          

                          Example: Configuring a Mobile Map Under LMA Configuration and Applying it on an Interface

                          Device> enable 
                          Device# configure terminal
                          Device(config)# ipv6 mobile pmipv6-lma lma1 domain dn1 
                          Device(config-ipv6-pmipv6-domain)# mobile-map mobilemap1 10
                          Device(config-ipv6-pmipv6-domain-mobile-map)# interface gigabitethernet 0/0/0
                          Device(config-ipv6-pmipv6-domain-mobile-map)# end

                          Example: Configuring the MTU to be Applied on the PMIPv6 Tunnel

                          Device> enable
                          Device# configure terminal
                          Device(config)# ipv6 mobile pmipv6-lma lma1 domain dn1
                          Device(config-ipv6-pmipv6-lma)# tunnel mtu 1360
                          Device(config-ipv6-pmipv6-lma)# end

                          Example: Configuring Multiple Mobile Network Pools for a Network Under LMA Configuration

                          Device> enable
                          Device# configure terminal
                          Device(config)# ipv6 mobile pmipv6-lma lma1 domain dn1 
                          Device(config-ipv6-pmipv6-lma)# network name
                          Device(config-ipv6-pmipv6lma-network)# mobile-network pool 10.20.2.1 pool-prefix 24 network-prefix 30 
                          Device(config-ipv6-pmipv6lma-network)# mobile-network pool 10.20.3.1 pool-prefix 24 network-prefix 30
                          Device(config-ipv6-pmipv6lma-network)# end

                          Example: Configuring Heartbeat under LMA Configuration

                          Device> enable
                          Device# configure terminal
                          Device(config)# ipv6 mobile pmipv6-lma lma1 domain dn1
                          Device(config-ipv6-pmipv6-lma)# heartbeat interval 300 retries 2 label label1 natreboot
                          Device(config-ipv6-pmipv6-lma)# end

                          Example: Configuring Multipath Management

                          Example: Configuring Multipath Management on LMA

                          Device> enable
                          Device# configure terminal
                          Device(config)# ipv6 mobile pmipv6-domain D1
                          Device(config-ipv6-pmipv6-domain)# mobile-map MAP1 12
                          Device(config-ipv6-pmipv6-domain-mobile-map)# match access-list voice
                          Device(config-ipv6-pmipv6-domain-mobile-map)# set link-type lte_intf 3g_intf
                          Device(config-ipv6-pmipv6-domain-mobile-map)# ipv6 mobile pmipv6-lma LMA1 domain D1
                          Device(config-ipv6-pmipv6-lma)# address ipv4 9.9.9.1
                          Device(config-ipv6-pmipv6-lma)# heartbeat interval 15 retries 1
                          Device(config-ipv6-pmipv6-lma)# bce maximum 128000
                          Device(config-ipv6-pmipv6-lma)# default profile RegularMn
                          Device(config-ipv6-pmipv6-lma)# dynamic mag learning
                          Device(config-ipv6-pmipv6-lma)# multipath
                          Device(config-ipv6-pmipv6-lma)# mobile-map MAP1
                          Device(config-ipv6-pmipv6-lma)# tunnel mtu 1360
                          Device(config-ipv6-pmipv6-lma)# interface Ethernet0/2
                          Device(config-ipv6-pmipv6-lma)# network net1
                          Device(config-ipv6-pmipv6lma-network)# pool ipv4 v4pool pfxlen 24
                          Device(config-ipv6-pmipv6lma-network)# mobile-network pool 20.20.2.1 pool-prefix 24 network-prefix 30
                          Device(config-ipv6-pmipv6lma-network)# mobile-network pool 20.20.1.1 pool-prefix 24 network-prefix 30
                          Device(config-ipv6-pmipv6lma-network)# mobile-network pool 30.30.2.1 pool-prefix 24 network-prefix 30
                          Device(config-ipv6-pmipv6lma-network)# network net2
                          Device(config-ipv6-pmipv6lma-network)# pool ipv4 rv4pool pfxlen 16
                          Device(config-ipv6-pmipv6lma-network)# network net3
                          Device(config-ipv6-pmipv6lma-network)# pool ipv4 netpool2 pfxlen 24
                          Device(config-ipv6-pmipv6lma-network)# mobile-network pool 31.31.1.1 pool-prefix 24 network-prefix 30
                          Device(config-ipv6-pmipv6lma-network)# mobile-network pool 20.20.4.1 pool-prefix 24 network-prefix 30
                          Device(config-ipv6-pmipv6lma-network)# mobile-network pool 20.20.3.1 pool-prefix 24 network-prefix 30
                          Device(config-ipv6-pmipv6lma-network)# mobile-network pool 30.30.5.1 pool-prefix 23 network-prefix 30
                          Device(config-ipv6-pmipv6lma-network)# end

                          Example: Configuring Multipath Management on MAG

                          Device> enable
                          Device# configure terminal
                          Device(config)# ipv6 mobile pmipv6-domain D1
                          Device(config-ipv6-pmipv6-domain)# mobile-map MAP1 12
                          Device(config-ipv6-pmipv6-domain-mobile-map)# match access-list voice
                          Device(config-ipv6-pmipv6-domain-mobile-map)# traffic-profile haccess-voice
                          Device(config-ipv6-pmipv6-domain-mobile-map)# ipv6 mobile pmipv6-mag MAG1 domain D1
                          Device(config-ipv6-pmipv6-mag)# address dynamic
                          Device(config-ipv6-pmipv6-mag-addr-dyn)# roaming interface Ethernet1/0 priority 1 egress-att LTE label lte_intf
                          Device(config-ipv6-pmipv6-mag-addr-dyn)# roaming interface Ethernet1/1 priority 2 egress-att 3G label 3g_intf
                          Device(config-ipv6-pmipv6-mag-addr-dyn)# exit
                          Device(config-ipv6-pmipv6-mag)# heartbeat interval 15 retries 1
                          Device(config-ipv6-pmipv6- mag)# bce maximum 128000
                          Device(config-ipv6-pmipv6- mag)# multipath
                          Device(config-ipv6-pmipv6- mag)# mobile-map MAP1
                          Device(config-ipv6-pmipv6- mag)# tunnel mtu 1360
                          Device(config-ipv6-pmipv6- mag)# interface Ethernet0/2
                          Device(config-ipv6-pmipv6- mag)# lma LMA1 D1
                          Device(config-ipv6-pmipv6-mag)# mobility-service hybrid-access
                          Device(config-ipv6-pmipv6-mag-haccess-svc)# profile-definition haccess-voice
                          Device(config-ipv6-pmipv6-mag-haccess-profile-def-svc)# jitter 50
                          Device(config-ipv6-pmipv6-mag-haccess-profile-def-svc)# rtt 100
                          Device(config-ipv6-pmipv6-mag-haccess-profile-def-svc)# packet-loss 2
                          Device(config-ipv6-pmipv6-mag-haccess-profile-def-svc)# end

                          Additional References

                          Related Documents

                          Related Topic

                          Document Title

                          Cisco IOS commands

                          Cisco IOS Master Command List, All Releases

                          IP mobility commands

                          Cisco IOS IP Mobility Command Reference

                          Standards and RFCs

                          Standard/RFC

                          Title

                          RFC 3775

                          Mobility Support in IPv6

                          RFC 5213

                          Proxy Mobile IPv6

                          RFC 5844

                          IPv4 Support for Proxy Mobile IPv6

                          RFC 5845

                          Generic Routing Encapsulation (GRE) Key Option for Proxy Mobile IPv6

                          RFC 5846

                          Binding Revocation for IPv6 Mobility

                          MIBs

                          MIB

                          MIBs Link

                          None

                          To locate and download MIBs for selected platforms, Cisco software releases, and feature sets, use Cisco MIB Locator found at the following URL:

                          http:/​/​www.cisco.com/​go/​mibs

                          Technical Assistance

                          Description

                          Link

                          The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.

                          http:/​/​www.cisco.com/​cisco/​web/​support/​index.html

                          Feature Information for PMIP: Multipath Support on MAG and LMA

                          The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

                          Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.
                          Table 1 Feature Information for PMIP: Multipath Support on MAG and LMA

                          Feature Name

                          Releases

                          Feature Information

                          PMIP: Multipath Support on MAG and LMA

                          The PMIP: Multipath Support on MAG and LMA feature enables Mobility Access Gateway (MAG) to register multiple transport end-points with Local Mobility Anchor (LMA), allowing MAG and LMA to establish multiple tunnels and apply path selection on a flow basis.

                          The following commands were introduced or modified: encap (proxy mobile IPv6), heartbeat, interface (proxy mobile IPv6) , match access-list (PMIPv6), mobile-map (PMIPv6 domain), mobile-map (LMA), mobile-network PMIPv6), multipath, set link-type, tunnel mtu, .

                          PMIPv6 Multipath Management

                          The PMIPv6 Mutipath Management feature enables PMIPv6 to choose from multiple available links which have different access technologies.

                          The following commands were introduced or modified: address dynamic, bce maximum, default profile, dynamic mag learning, heartbeat, jitter, match access-list, mobile-map, mobility-service hybrid-access, packet loss, profile-definition, rtt, set link-type, traffic-profile.