QoS Match VLAN

The QoS: Match VLAN feature allows you to classify network traffic on the basis of the Layer 2 virtual local-area network (VLAN) identification number.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.

Information About Match VLAN

QoS Match VLAN

The QoS: Match VLAN feature allows you to classify network traffic on the basis of the Layer 2 virtual local-area network (VLAN) identification number. To classify network traffic based on the VLAN identification number you create a class-map and specify the match criteria using the match vlan command. You then attach the class to a policy-map and use the policy map in a service policy that is attached to an interface.

How to Configure Match VLAN

Classifying Network Traffic per VLAN

To classify network traffic on a per VLAN basis, perform the following task.

SUMMARY STEPS

  1. enable
  2. configure terminal
  3. class-map {match-any | match-all} class-map-name
  4. match vlan vlan-id-number
  5. exit
  6. policy-map policy-map-name
  7. class class-map-name
  8. bandwidth percent percent
  9. exit
  10. exit
  11. policy-map policy-map-name
  12. class class-map-name
  13. shape {average | peak} cir
  14. service-policy {input | output} policy-map-name
  15. exit
  16. exit
  17. interface type number [name-tag ]
  18. service-policy {input | output} policy-map-name
  19. end

DETAILED STEPS

  Command or Action Purpose
Step 1

enable

Example:


Router> enable

Enables privileged EXEC mode.

  • Enter your password if prompted.

Step 2

configure terminal

Example:


Router# configure terminal

Enters global configuration mode.

Step 3

class-map {match-any | match-all} class-map-name

Example:


Router(config)# class-map match-any Blue_VRF

Creates a class map and enters class map configuration mode.

Step 4

match vlan vlan-id-number

Example:


Router(config-cmap)# match vlan 101

Matches traffic on the basis of the range of VLAN identification numbers specified.

Step 5

exit

Example:


Router(config-cmap)# exit

Returns to global configuration mode.

Step 6

policy-map policy-map-name

Example:


Router(config)# policy-map Shared_QoS

Creates a policy map that can be attached to an interface and enters policy-map configuration mode.

Step 7

class class-map-name

Example:


Router(config-pmap)# class Blue_VRF

Specify the name of the class whose policy you want to create and enters policy-map class configuration mode.

Step 8

bandwidth percent percent

Example:


Router(config-pmap-c)# bandwidth percent 30

Specifies the bandwidth allocated for a class belonging to a policy map.

Step 9

exit

Example:


Router(config-pmap-c)# exit

Returns to policy-map configuration mode.

Step 10

exit

Example:


Router(config-pmap)# exit

Returns to global configuration mode.

Step 11

policy-map policy-map-name

Example:


Router(config)# policy-map COS-OUT-SHAPED

Creates a policy map that can be attached to an interface and enters policy-map configuration mode.

Step 12

class class-map-name

Example:


Router(config-pmap)# class FROM_WAN

Specify the name of the class whose policy you want to create and enters policy-map class configuration mode.

Step 13

shape {average | peak} cir

Example:


Router(config-pmap-c)# shape average 9000000000
Specifies the average rate traffic shaping.

  • The Committed information rate (CIR), is specified in bits per second (bps).

Step 14

service-policy {input | output} policy-map-name

Example:


Router(config-pmap-c)# service-policy Shared_QoS

Specifies the name of the predefined policy map to be used as a QoS policy.

Step 15

exit

Example:


Router(config-pmap-c)# exit

Returns to policy-map configuration mode.

Step 16

exit

Example:


Router(config-pmap)# exit

Returns to global configuration mode.

Step 17

interface type number [name-tag ]

Example:


Router(config)# interface FastEthernet 0/0.1

Configures an interface type and enters interface configuration mode.

  • Enter the interface type and number.

Step 18

service-policy {input | output} policy-map-name

Example:


Router(config-if)# service-policy output COS-OUT-SHAPED

Attaches a policy map to an input interface, a virtual circuit (VC), an output interface, or a VC that will be used as the service policy for the interface.

Step 19

end

Example:


Router(config-if)# end

(Optional) Exits interface configuration mode and returns to privileged EXEC mode.

Configuration Examples for Match VLAN

Example: Classifying Network Traffic per VLAN

The following example shows how to classify network traffic on a VLAN basis. The VLAN classified traffic is applied to the FastEthernet 0/0.1 subinterface. 

interface FastEthernet0/0.1
service-policy output COS-OUT-SHAPED
policy-map COS-OUT-SHAPED
      class ADMIN
      class FROM_WAN
               shape average 900000000
               service-policy Shared_QoS
policy-map Shared_QoS
      ! description -- Bandwidth sharing between VRF --
      class Blue_VRF
               bandwidth percent 3
class-map match-any Blue_VRF
      ! description -- traffic belonging to the VRF Blue --
      match vlan  101

Additional References for QoS for Match VLAN

Related Documents

Related Topic

Document Title

Cisco commands

Cisco IOS Master Command List, All Releases

QoS commands: complete command syntax, command modes, command history, defaults, usage guidelines, and examples

Cisco IOS Quality of Service Solutions Command Reference

Classifying network traffic

“Classifying Network Traffic” module

MQC

“Applying QoS Features Using the MQC” module

Marking network traffic

“Marking Network Traffic” module

Technical Assistance

Description

Link

The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.

http://www.cisco.com/cisco/web/support/index.html

Feature Information for QoS for Match VLAN

The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.
Table 1. Feature Information for QoS for Match VLAN

Feature Name

Releases

Feature Information

QoS: Match VLAN

12.2(31)SB2

Cisco IOS XE Release 2.1

15.0(1)S

The QoS: Match VLAN feature allows you to classify network traffic on the basis of the Layer 2 virtual local-area network (VLAN) identification number. The following commands were introduced or modified by this feature: match vlan (QoS), show policy-map interface

This feature was introduced on Cisco ASR 1000 Series Routers.