Shaping on Dialer Interfaces

The Shaping on Dialer Interfaces feature provides support for Point-to-Point Protocol over Ethernet (PPPoE) and Point-to-Point Protocol over Asynchronous Transfer Mode (PPPoA) configurations on dialer interfaces. The feature provides support for Modular QoS CLI (MQC)-based queuing and shaping that supports per-customer quality of service (QoS). Parent policies are attached to an Ethernet in the First Mile (EFM) interface, and child policies are attached to individual dialer interfaces. Class of service (CoS) values are set by applying a policy to the dialer interface. The feature also enables the collection of queuing statistics on the dialer interface and the polling of traffic counters for dialer interfaces.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

Restrictions for Shaping on Dialer Interfaces

  • The output queueing policy must have a parent class-default shaper, and any other queueing actions must be configured in a child policy.

Information About Shaping on Dialer Interfaces

QoS on PPP Session on Dialer Interfaces

The Shaping on Dialer Interfaces feature consolidates the output queueing and classification on the egress interface (where all the queueing features are run). The police and set features (such as CoS marking) also work in the output path.

MQC-based QoS queuing and shaping features can be used to attach flat class-default shaped policies to the EFM and attach HQoS parent-shaped policies to the dialer interface.

Policies are applied to the dialer interface using the service-policy command. In addition the related show and debug commands display policy and queueing statistics associated with the dialer target.


Note
In Cisco ASR1000 devices, dialer policy is suspended when there is no forwarding interface configured for the dialer. However, in Cisco ISR devices, the dialer policy is not suspended when there is no forwarding interface configured.

QoS Dialer Interface Topology

The following figure shows the supported topology for the Shaping on Dialer Interfaces feature:

Figure 1. Shaping on Dialer Interfaces Topology

The Customer Premises Equipment (CPE) is shared between several customers. Each customer connects to the CPE through a VLAN on a Gigabit Ethernet port. The CPE connects to the service over a DSL using an EFM interface (this looks like an Ethernet connection but uses DSL) over which all the incoming VLANs will be forwarded. The traffic for each VLAN (customer) is transmitted in a separate PPP session. Each session is set up using a dialer interface.

How to Configure Shaping on Dialer Interfaces

Configuring an Output Queueing Policy for Dialer Interfaces

Before You Begin

Because the dialer target is added to the dynamic target API, the output queueing policy must have a parent class-default shaper with any other queueing actions configured in a child policy.

SUMMARY STEPS

    1.    enable

    2.    configure terminal

    3.    policy-map policy-map-name

    4.    class class-name

    5.    priority percent percentage

    6.    exit

    7.    class class-name

    8.    bandwidth percent percentage

    9.    exit

    10.    class {class-name | class-default}

    11.    fair-queue

    12.    exit

    13.    exit

    14.    policy-map policy-map-name

    15.    class class-default

    16.    shape average target-bit-rate

    17.    service-policy policy-map-name

    18.    exit

    19.    exit

    20.    interface type number

    21.    service-policy output policy-name

    22.    exit


DETAILED STEPS
     Command or ActionPurpose
    Step 1 enable


    Example: 
    Device> enable
     

    Enables privileged EXEC mode.

    • Enter your password if prompted.

     
    Step 2 configure terminal


    Example: 
    Device# configure terminal
     

    Enters global configuration mode.

     
    Step 3 policy-map policy-map-name


    Example: 
    Device(config)# policy-map child
     

    Specifies the name of the policy map created earlier and enters policy-map configuration mode.

    • Enter the policy map name.

     
    Step 4 class class-name


    Example: 
    Device(config-pmap)# class voice
     

    Specifies the name of the class whose policy you want to create and enters policy-map class configuration mode. This class is associated with the class map created earlier.

    • Enter the name of the class or enter the class-default keyword.

     
    Step 5 priority percent percentage


    Example: 
    Device(config-pmap-c)# priority percent 30
     

    Specifies that the amount of guaranteed bandwidth will be specified by the percent of available bandwidth.

     
    Step 6 exit


    Example: 
    Device(config-pmap-c)# exit
     

    Returns to policy-map configuration mode.

     
    Step 7 class class-name


    Example: 
    Device(config-pmap)# class video
     

    Specifies the name of the class whose policy you want to create and enters policy-map class configuration mode. This class is associated with the class map created earlier.

    • Enter the name of the class or enter the class-default keyword.

     
    Step 8 bandwidth percent percentage


    Example: 
    Device(config-pmap-c)# bandwidth percent 50
     

    Specifies that the amount of guaranteed bandwidth will be specified by the percent of total bandwidth.

     
    Step 9 exit


    Example: 
    Device(config-pmap-c)# exit
     

    Returns to policy-map configuration mode.

     
    Step 10 class {class-name | class-default}


    Example: 
    Device(config-pmap)# class class-default
     

    Specifies the name of the class whose policy you want to create and enters policy-map class configuration mode. This class is associated with the class map created earlier.

    • Enter the name of the class or enter the class-default keyword.

     
    Step 11 fair-queue


    Example: 
    Device(config-pmap-c)# fair-queue
     

    Enables flow-based fair queueing in this class.

     
    Step 12 exit


    Example: 
    Device(config-pmap-c) exit
     

    Returns to policy-map configuration mode.

     
    Step 13 exit


    Example: 
    Device(config-pmap) exit
     

    Returns to global configuration mode.

     
    Step 14 policy-map policy-map-name


    Example: 
    Device(config)# policy-map parent
     

    Specifies the name of a policy map and enters policy-map configuration mode.

    • Enter the policy map name.

     
    Step 15 class class-default


    Example: 
    Device(config-pmap)# class class-default
     

    Creates the class-default class.

     
    Step 16 shape average target-bit-rate


    Example: 
    Device(config-pmap-c)# shape average 1000000
     

    Specifies average rate traffic shaping as bits-per-second on an interface.

     
    Step 17 service-policy policy-map-name


    Example: 
    Device(config-pmap-c)# service policy child
     

    Configures a service policy policy map.

     
    Step 18 exit


    Example: 
    Device(config-pmap-c) exit
     

    Returns to policy-map configuration mode.

     
    Step 19 exit


    Example: 
    Device(config-pmap) exit
     

    Returns to global configuration mode.

     
    Step 20 interface type number


    Example: 
    Device(config)# interface Dialer 0
     

    Configures an interface type and enters interface configuration mode.

    • Enter the interface type and number.

     
    Step 21 service-policy output policy-name


    Example: 
    Device(config-if)# service-policy output parent
     

    Attaches a policy map to an output interface that will be used as the service policy for the interface.

     
    Step 22 exit


    Example: 
    Device(config-if) exit
     

    Returns to global configuration mode.

     

    Configuring QoS for PPPoEoA for Dialer Interfaces

    SUMMARY STEPS

      1.    enable

      2.    configure terminal

      3.    interface type number [name-tag]

      4.    no ip address

      5.    no atm ilmi-keepalive

      6.    exit

      7.    interface type number [name-tag]

      8.    pvc vpi/vci

      9.    vbr-nrt output-pcr output-scr

      10.    pppoe-client dial-pool-number number

      11.    exit

      12.    exit

      13.    interface type number [name-tag]

      14.    mtu ip-address

      15.    ip address ip-address mask

      16.    encapsulation encapsulation-type

      17.    dialer pool number

      18.    dialer-group number

      19.    service-policy output name

      20.    exit

      21.    dialer-list dialer-group protocol protocol-name permit


    DETAILED STEPS
       Command or ActionPurpose
      Step 1 enable


      Example:
      Device> enable
       

      Enables privileged EXEC mode.

      • Enter your password if prompted.

       
      Step 2 configure terminal


      Example:
      Device# configure terminal
       

      Enters global configuration mode.

       
      Step 3 interface type number [name-tag]


      Example:
      Device(config)# interface ATM 0
       

      Configures an interface type and enters interface configuration mode.

      • Enter the interface type and number.

       
      Step 4 no ip address


      Example:
      Device(config-if)# no ip address
       

      Disables IP processing on the interface.

       
      Step 5 no atm ilmi-keepalive


      Example:
      Device(config-if)# no atm ilmi-keepalive
       

      Disables Interim Local Management Interface (ILMI) keepalives on the interface.

       
      Step 6 exit


      Example:
      Device(config-if)# exit
       

      Exits interface configuration mode.

       
      Step 7 interface type number [name-tag]


      Example:
      Device(config)# interface ATM 0.1 point-to-point
       

      Configures an interface type and enters interface configuration mode.

      • Enter the interface type, number, and name.

       
      Step 8 pvc vpi/vci


      Example:
      Device(config-if)# pvc 4/46
       

      Creates an ATM permanent virtual circuit (PVC), and enters ATM virtual circuit configuration mode.

      • Enter the ATM network virtual path identifier (VPI) and ATM network virtual channel identifier (VCI) for this PVC.

       
      Step 9 vbr-nrt output-pcr output-scr


      Example:
      Device(config-if-atm-vc)# vbr-nrt 738 738
       

      Configures the variable bit rate-nonreal time (VBR-NRT) quality of service (QoS) and specifies the output peak cell rate (PCR), and output sustainable cell rate (SCR) for an ATM permanent virtual circuit (PVC).

       
      Step 10 pppoe-client dial-pool-number number


      Example:
      Device(config-if-atm-vc)# pppoe-client dial-pool-number 1
       

      Configures a PPP over Ethernet (PPPoE) client and specifies the dial-on-demand routing (DDR) functionality.

       
      Step 11 exit


      Example:
      Device(config-if-atm-vc)# exit
       

      Exits ATM virtual circuit configuration mode.

       
      Step 12 exit


      Example:
      Device(config-if)# exit
       

      Exits interface configuration mode.

       
      Step 13 interface type number [name-tag]


      Example:
      Device(config)# interface Dialer 0
       

      Configures an interface type and enters interface configuration mode.

      • Enter the interface type and number.

       
      Step 14 mtu ip-address


      Example:
      Device(config-if)# mtu 1200
       

      Adjusts the maximum packet size or maximum transmission unit (MTU) size.

       
      Step 15 ip address ip-address mask


      Example:
      Device(config-if)# ip address 172.16.0.0 255.0.0.0
       

      Sets the primary IP address for the interface.

      • Enter the IP address and the IP address mask.

       
      Step 16 encapsulation encapsulation-type


      Example:
      Device(config-if)# encapsulation ppp
       

      Sets the encapsulation method used by the interface.

       
      Step 17 dialer pool number


      Example:
      Device(config-if)# dialer pool 1
       

      Specifies the dialing pool that the dialer interface uses to connect to a specific destination subnetwork.

       
      Step 18 dialer-group number


      Example:
      Device(config-if)# dialer-group 1
       

      Controls access by configuring the interface to belong to a specific dialing group.

       
      Step 19 service-policy output name


      Example:
      Device(config-if)# service-policy output dialer-output-sp
       

      Attaches a policy map to an output interface that will be used as the service policy for the interface.

       
      Step 20 exit


      Example:
      Device(config-if)# exit
       

      Exits interface configuration mode.

       
      Step 21 dialer-list dialer-group protocol protocol-name permit


      Example:
      Device(config)# dialer-list 1 protocol ip permit
       

      Defines a dial-on-demand routing (DDR) dialer list for dialing by protocol or by a combination of a protocol and a previously defined access list.

       

      Configuring QoS for PPPoE for Dialer Interfaces

      SUMMARY STEPS

        1.    enable

        2.    configure terminal

        3.    interface type number [name-tag]

        4.    ppp enable group group-name

        5.    pppoe-client dial-pool-number number

        6.    exit

        7.    interface type number [name-tag]

        8.    mtu ip-address

        9.    ip address ip-address mask

        10.    encapsulation encapsulation-type

        11.    dialer pool number

        12.    dialer-group number

        13.    service-policy output name

        14.    exit

        15.    dialer-list dialer-group protocol protocol-name permit


      DETAILED STEPS
         Command or ActionPurpose
        Step 1 enable


        Example:
        Device> enable
         

        Enables privileged EXEC mode.

        • Enter your password if prompted.

         
        Step 2 configure terminal


        Example:
        Device# configure terminal
         

        Enters global configuration mode.

         
        Step 3 interface type number [name-tag]


        Example:
        Device(config)# interface Ethernet 0/0
         

        Configures an interface type and enters interface configuration mode.

        • Enter the interface type, number, and name.

         
        Step 4 ppp enable group group-name


        Example:
        Device(config-if)# ppp enable group global
         

        Enables PPPoE sessions on an Ethernet interface or subinterface.

         
        Step 5 pppoe-client dial-pool-number number


        Example:
        Device(config-if)# pppoe-client dial-pool-number 1
         

        Configures a PPPoE client and to specify the dial-on-demand routing (DDR) functionality.

         
        Step 6 exit


        Example:
        Device(config-if)# exit
         

        Exits interface configuration mode.

         
        Step 7 interface type number [name-tag]


        Example:
        Device(config)# interface Dialer 0
         

        Configures an interface type and enters interface configuration mode.

        • Enter the interface type and number.

         
        Step 8 mtu ip-address


        Example:
        Device(config-if)# mtu 1200
         

        Adjusts the maximum packet size or maximum transmission unit (MTU) size.

         
        Step 9 ip address ip-address mask


        Example:
        Device(config-if)# ip address 172.16.0.0 255.0.0.0
         

        Sets the primary IP address for the interface.

        • Enter the IP address and the IP address mask.

         
        Step 10 encapsulation encapsulation-type


        Example:
        Device(config-if)# encapsulation ppp
         

        Sets the encapsulation method used by the interface.

         
        Step 11 dialer pool number


        Example:
        Device(config-if)# dialer pool 1
         

        Specifies the dialing pool that the dialer interface uses to connect to a specific destination subnetwork.

         
        Step 12 dialer-group number


        Example:
        Device(config-if)# dialer-group 1
         

        Controls access by configuring the interface to belong to a specific dialing group.

         
        Step 13 service-policy output name


        Example:
        Device(config-if)# service-policy output dialer-output-sp
         

        Attaches a policy map to an output interface that will be used as the service policy for the interface.

         
        Step 14 exit


        Example:
        Device(config-if)# exit
         

        Exits interface configuration mode.

         
        Step 15 dialer-list dialer-group protocol protocol-name permit


        Example:
        Device(config)# dialer-list 1 protocol ip permit
         

        Defines a dial-on-demand routing (DDR) dialer list for dialing by protocol or by a combination of a protocol and a previously defined access list.

         

        Configuring QoS for PPPoA for Dialer Interfaces

        SUMMARY STEPS

          1.    enable

          2.    configure terminal

          3.    interface type number [name-tag]

          4.    pvc vpi/vci

          5.    vbr-nrt output-pcr output-scr output-maxburstsize

          6.    dialer pool-member number

          7.    protocol protocol

          8.    exit

          9.    exit

          10.    interface type number [name-tag]

          11.    mtu ip-address

          12.    ip address ip-address mask

          13.    encapsulation encapsulation-type

          14.    dialer pool number

          15.    dialer-group number

          16.    service-policy output name

          17.    exit

          18.    dialer-list dialer-group protocol protocol-name permit


        DETAILED STEPS
           Command or ActionPurpose
          Step 1 enable


          Example:
          Device> enable
           

          Enables privileged EXEC mode.

          • Enter your password if prompted.

           
          Step 2 configure terminal


          Example:
          Device# configure terminal
           

          Enters global configuration mode.

           
          Step 3 interface type number [name-tag]


          Example:
          Device(config)# interface ATM 0.1 point-to-point
           

          Configures an interface type and enters interface configuration mode.

          • Enter the interface type, number, and name.

           
          Step 4 pvc vpi/vci


          Example:
          Device(config-if)# pvc 4/46
           

          Creates an ATM permanent virtual circuit (PVC), and enters ATM virtual circuit configuration mode.

          • Enter the ATM network virtual path identifier (VPI) and ATM network virtual channel identifier (VCI) for this PVC.

           
          Step 5 vbr-nrt output-pcr output-scr output-maxburstsize


          Example:
          Device(config-if-atm-vc)# vbr-nrt 738 738 32
           

          Configures the variable bit rate-nonreal time (VBR-NRT) quality of service (QoS) and specifies the output peak cell rate (PCR), output sustainable cell rate (SCR), and output maximum burst cell size for an ATM permanent virtual circuit (PVC).

           
          Step 6 dialer pool-member number


          Example:
          Device(config-if-atm-vc)# dialer pool-member 1
           

          Configures a physical interface to be a member of a dialer profiles dialing pool.

           
          Step 7 protocol protocol


          Example:
          Device(config-if-atm-vc)# protocol ppp dialer
           

          Configures a static map for an ATM permanent virtual circuit (PVC), switched virtual circuit (SVC), or virtual circuit (VC) class.

           
          Step 8 exit


          Example:
          Device(config-if-atm-vc)# exit
           

          Exits ATM virtual circuit configuration mode.

           
          Step 9 exit


          Example:
          Device(config-if)# exit
           

          Exits interface configuration mode.

           
          Step 10 interface type number [name-tag]


          Example:
          Device(config)# interface Dialer 0
           

          Configures an interface type and enters interface configuration mode.

          • Enter the interface type and number.

           
          Step 11 mtu ip-address


          Example:
          Device(config-if)# mtu 1200
           

          Adjusts the maximum packet size or maximum transmission unit (MTU) size.

           
          Step 12 ip address ip-address mask


          Example:
          Device(config-if)# ip address 172.16.0.0 255.0.0.0
           

          Sets the primary IP address for the interface.

          • Enter the IP address and the IP address mask.

           
          Step 13 encapsulation encapsulation-type


          Example:
          Device(config-if)# encapsulation ppp
           

          Sets the encapsulation method used by the interface.

           
          Step 14 dialer pool number


          Example:
          Device(config-if)# dialer pool 1
           

          Specifies the dialing pool that the dialer interface uses to connect to a specific destination subnetwork.

           
          Step 15 dialer-group number


          Example:
          Device(config-if)# dialer-group 1
           

          Controls access by configuring the interface to belong to a specific dialing group.

           
          Step 16 service-policy output name


          Example:
          Device(config-if)# service-policy output dialer-output-sp
           

          Attaches a policy map to an output interface that will be used as the service policy for the interface.

           
          Step 17 exit


          Example:
          Device(config-if)# exit
           

          Exits interface configuration mode.

           
          Step 18 dialer-list dialer-group protocol protocol-name permit


          Example:
          Device(config)# dialer-list 1 protocol ip permit
           

          Defines a dial-on-demand routing (DDR) dialer list for dialing by protocol or by a combination of a protocol and a previously defined access list, .

           

          Configuring QoS for Multiple Sessions on Dialer Interfaces

          SUMMARY STEPS

            1.    enable

            2.    configure terminal

            3.    interface type number [name-tag]

            4.    ppp enable group group-name

            5.    pppoe-client dial-pool-number number

            6.    pppoe-client dial-pool-number number

            7.    pppoe-client dial-pool-number number

            8.    exit

            9.    interface type number [name-tag]

            10.    dialer pool number

            11.    service-policy output name

            12.    exit

            13.    interface type number [name-tag]

            14.    dialer pool number

            15.    service-policy output name

            16.    exit

            17.    interface type number [name-tag]

            18.    dialer pool number

            19.    service-policy output name

            20.    exit


          DETAILED STEPS
             Command or ActionPurpose
            Step 1 enable


            Example:
            Device> enable
             

            Enables privileged EXEC mode.

            • Enter your password if prompted.

             
            Step 2 configure terminal


            Example:
            Device# configure terminal
             

            Enters global configuration mode.

             
            Step 3 interface type number [name-tag]


            Example:
            Device(config)# interface Ethernet 0/0
             

            Configures an interface type and enters interface configuration mode.

            • Enter the interface type, number, and name.

             
            Step 4 ppp enable group group-name


            Example:
            Device(config-if)# ppp enable group global
             

            Enables PPPoE sessions on an Ethernet interface or subinterface.

             
            Step 5 pppoe-client dial-pool-number number


            Example:
            Device(config-if)# pppoe-client dial-pool-number 1
             

            Configures a PPPoE client and to specify the dial-on-demand routing (DDR) functionality.

             
            Step 6 pppoe-client dial-pool-number number


            Example:
            Device(config-if)# pppoe-client dial-pool-number 2
             

            Configures a PPPoE client and to specify the dial-on-demand routing (DDR) functionality.

             
            Step 7 pppoe-client dial-pool-number number


            Example:
            Device(config-if)# pppoe-client dial-pool-number 3
             

            Configures a PPPoE client and to specify the dial-on-demand routing (DDR) functionality.

             
            Step 8 exit


            Example:
            Device(config-if)# exit
             

            Exits interface configuration mode.

             
            Step 9 interface type number [name-tag]


            Example:
            Device(config)# interface Dialer 0
             

            Configures an interface type and enters interface configuration mode.

            • Enter the interface type and number.

             
            Step 10 dialer pool number


            Example:
            Device(config-if)# dialer pool 1
             

            Specifies the dialing pool that the dialer interface uses to connect to a specific destination subnetwork.

             
            Step 11 service-policy output name


            Example:
            Device(config-if)# service-policy output dialer-output-sp
             

            Attaches a policy map to an output interface that will be used as the service policy for the interface.

             
            Step 12 exit


            Example:
            Device(config-if)# exit
             

            Exits interface configuration mode.

             
            Step 13 interface type number [name-tag]


            Example:
            Device(config)# interface Dialer 1
             

            Configures an interface type and enters interface configuration mode.

            • Enter the interface type and number.

             
            Step 14 dialer pool number


            Example:
            Device(config-if)# dialer pool 2
             

            Specifies the dialing pool that the dialer interface uses to connect to a specific destination subnetwork.

             
            Step 15 service-policy output name


            Example:
            Device(config-if)# service-policy output dialer-output-sp
             

            Attaches a policy map to an output interface that will be used as the service policy for the interface.

             
            Step 16 exit


            Example:
            Device(config-if)# exit
             

            Exits interface configuration mode.

             
            Step 17 interface type number [name-tag]


            Example:
            Device(config)# interface Dialer 2
             

            Configures an interface type and enters interface configuration mode.

            • Enter the interface type and number.

             
            Step 18 dialer pool number


            Example:
            Device(config-if)# dialer pool 3
             

            Specifies the dialing pool that the dialer interface uses to connect to a specific destination subnetwork.

             
            Step 19 service-policy output name


            Example:
            Device(config-if)# service-policy output dialer-output-sp
             

            Attaches a policy map to an output interface that will be used as the service policy for the interface.

             
            Step 20 exit


            Example:
            Device(config-if)# exit
             

            Exits interface configuration mode.

             

            Applying CoS Values to a Dialer Interface

            Class of Service (CoS) values are set by applying a policy to the dialer interface.

            SUMMARY STEPS

              1.    enable

              2.    configure terminal

              3.    policy-map policy-map-name

              4.    class class-default

              5.    set cos cos-value

              6.    exit

              7.    exit

              8.    interface type number [name-tag]

              9.    service-policy output name

              10.    exit

              11.    interface type number [name-tag]

              12.    encapsulation encapsulation-type

              13.    pppoe-client dial-pool-number number

              14.    exit


            DETAILED STEPS
               Command or ActionPurpose
              Step 1 enable


              Example:
              Device> enable
               

              Enables privileged EXEC mode.

              • Enter your password if prompted.

               
              Step 2 configure terminal


              Example:
              Device# configure terminal
               

              Enters global configuration mode.

               
              Step 3 policy-map policy-map-name


              Example:
              Device(config)# policy-map output_cos
               

              Specifies the name of the policy map created earlier and enters policy-map configuration mode.

              • Enter the policy map name.

               
              Step 4 class class-default


              Example:
              Device(config-pmap)# class class-default
               

              Creates the default class for traffic classification and enters policy-map class configuration mode.

               
              Step 5 set cos cos-value


              Example:
              Device(config-pmap-c)# set cos 1
               

              Specifies an IEEE 802.1Q CoS value from 0 to 7.

               
              Step 6 exit


              Example:
              Device(config-pmap-c)# exit
               

              Returns to policy-map configuration mode.

               
              Step 7 exit


              Example:
              Device(config-pmap)# exit
               

              Returns to global configuration mode.

               
              Step 8 interface type number [name-tag]


              Example:
              Device(config)# interface Dialer 1
               

              Configures an interface type and enters interface configuration mode.

              • Enter the interface type and number.

               
              Step 9 service-policy output name


              Example:
              Device(config-if)# service-policy output output-cos
               

              Attaches a policy map to an output interface that will be used as the service policy for the interface.

               
              Step 10 exit


              Example:
              Device(config-if)# exit
               

              Exits interface configuration mode.

               
              Step 11 interface type number [name-tag]


              Example:
              Device(config)# interface Ethernet 0.10
               

              Configures an interface type and enters sub-interface configuration mode.

              • Enter the interface type and number.

               
              Step 12 encapsulation encapsulation-type


              Example:
              Device(config-subif)# encapsulation dot1q 10
               

              Sets the encapsulation method used by the interface.

               
              Step 13 pppoe-client dial-pool-number number


              Example:
              Device(config-subif)# pppoe-client dial-pool-number 1
               

              Configures a PPPoE client and to specify the dial-on-demand routing (DDR) functionality.

               
              Step 14 exit


              Example:
              Device(config-subif)# exit
               

              Returns to global configuration mode.

               

              Configuration Examples for Shaping on Dialer Interfaces

              Example: Configuring Output Queuing Policy for a Dialer Interface

              The following example shows how to configure parent and child policy maps and how to attach the parent map to the dialer interface: 

              Device(config)# policy-map childExample
 Device(config-pmap)# class voice
  Device(config-pmap-c)# priority percent 30
  Device(config-pmap-c)# exit

 Device(config-pmap)# class video
  Device(config-pmap-c)# bandwidth percent 50
  Device(config-pmap-c)# exit

 Device(config-pmap)# class class-default
  Device(config-pmap-c)# fair-queue
  Device(config-pmap-c)# exit

Device(config)# policy-map parent
 Device(config-pmap)# class class-default
  Device(config-pmap-c)# shape average 1000000
  Device(config-pmap-c)# service-policy child
  Device(config-pmap-c)# exit

Device(config)# interface dialer 0
 Device(config-if)# service-policy output parent

              Example: Configuring QoS for PPPoEoA for a Dialer Interface

              Device(config)# interface ATM 0
 Device(config-if)# no ip address
 Device(config-if)# no atm ilmi-keepalive
 Device(config-if)# exit

Device(config)# interface ATM 0.1 point-to-point
 Device(config-if)# ip address 192.168.0.0 255.255.255.224
 Device(config-if)# pvc 4/46
  Device(config-if-atm-vc)# vbr-nrt 738 738
  Device(config-if-atm-vc)# pppoe-client dial-pool-number 1
  Device(config-if-atm-vc)# exit
 Device(config-if)# exit

Device(config)# interface Dialer 0 
 Device(config-if)# mtu 1200 
 Device(config-if)# ip address 172.16.0.0 255.0.0.0 
 Device(config-if)# encapsulation ppp
 Device(config-if)# dialer pool 1
 Device(config-if)# dialer-group 1
 Device(config-if)# service-policy output dialer-output-sp
!
Device(config)# dialer-list 1 protocol ip permit

              Example: Configuring QoS for a PPPoE on a Dialer Interface

              Device(config)# interface ethernet 0/0
 Device(config-if)# pppoe enable group global
 Device(config-if)# pppoe-client dial-pool-number 1
 Device(config-if)# exit

Device(config)# interface Dialer 0 
 Device(config-if)# mtu 1200 
 Device(config-if)# ip address 172.16.0.0 255.0.0.0 
 Device(config-if)# encapsulation ppp
 Device(config-if)# dialer pool 1
 Device(config-if)# dialer-group 1
 Device(config-if)# service-policy output dialer-output-sp
 Device(config-if)# exit

Device(config)# dialer-list 1 protocol ip permit

              Example: Configuring QoS for PPPoA on a Dialer Interface

              Device(config)# interface ATM 0.1 point-to-point
 Device(config-if)# ip address 192.168.0.0 255.255.255.224
 Device(config-if)# pvc 4/46
  Device(config-if-atm-vc)# vbr-nrt 738 738
  Device(config-if-atm-vc)# dialer pool-member 1
  Device(config-if-atm-vc)# protocol ppp dialer
  Device(config-if-atm-vc)# exit
 Device(config-if)# exit

Device(config)# interface Dialer 0 
 Device(config-if)# mtu 1200 
 Device(config-if)# ip address 172.16.0.0 255.0.0.0 
 Device(config-if)# encapsulation ppp
 Device(config-if)# dialer pool 1
 Device(config-if)# dialer-group 1
 Device(config-if)# service-policy output dialer-output-sp
 Device(config-if)# exit

Device(config)# dialer-list 1 protocol ip permit

              Example: Configuring QoS for Multiple Sessions on a Dialer Interface

              Device(config)# interface ethernet 0/0
 Device(config-if)# pppoe enable group global
 Device(config-if)# pppoe-client dial-pool-number 1
 Device(config-if)# pppoe-client dial-pool-number 2
 Device(config-if)# pppoe-client dial-pool-number 3
 Device(config-if)# exit

Device(config)# interface Dialer 0 
 Device(config-if)# dialer pool 1
 Device(config-if)# service-policy output dialer-output-sp
 Device(config-if)# exit

Device(config)# interface Dialer 1 
 Device(config-if)# dialer pool 2
 Device(config-if)# service-policy output dialer-output-sp
 Device(config-if)# exit

Device(config)# interface Dialer 2 
 Device(config-if)# dialer pool 3
 Device(config-if)# service-policy output dialer-output-sp
 Device(config-if)# exit

              Example: Applying CoS Values to a Dialer Interface

              Device> enable
Device# configure terminal
Device(config)# policy-map output_cos
Device(config-pmap)# class class-default
Device(config-pmap-c)# set cos 1
Device(config-pmap-c)# exit
Device(config-pmap)# exit
Device(config)# interface Dialer 1
Device(config-if)# service-policy output output-cos
Device(config-if)# exit
Device(config)# interface Ethernet 0.10
Device(config-subif)# encapsulation dot1q 10
Device(config-subif)# pppoe-client dial-pool-number 1
Device(config-subif)# exit

              Additional References for Shaping on Dialer Interfaces

              Related Documents

              Related Topic

              Document Title

              Cisco IOS commands

              Cisco IOS Master Commands List, All Releases

              QoS commands

              Cisco IOS Quality of Service Solutions Command Reference

              MQC

              QoS: Modular QoS: Command-Line Interface Configuration Guide

              Technical Assistance

              Description

              Link

              The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password.

              http:/​/​www.cisco.com/​cisco/​web/​support/​index.html

              Feature Information for Shaping on Dialer Interfaces

              The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

              Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.
              Table 1 Feature Information for Shaping on Dialer Interfaces

              Feature Name

              Releases

              Feature Information

              Shaping on Dialer Interfaces

              15.3(1)T

              Cisco IOS XE Release 3.13S

              The Shaping on Dialer Interfaces feature provides support for PPPoE/A configurations on dialer interfaces.