- Signalling Overview
- Configuring RSVP
- Control Plane DSCP Support for RSVP
- Configuring RSVP Support for Frame Relay
- RSVP Scalability Enhancements
- RSVP Support for ATM and PVCs
- RSVP Local Policy Support
- RSVP Refresh Reduction and Reliable Messaging
- RSVP Support for RTP Header Compression Phase 1
- RSVP Message Authentication
- RSVP-Previous Hop Overwrite
- Configuring RSVP Support for LLQ
- Configuring RSVP-ATM QoS Interworking
- Configuring COPS for RSVP
- RSVP Aggregation
- MPLS TE-Tunnel-Based Admission Control
- Configuring Subnetwork Bandwidth Manager
- Finding Feature Information
- COPS for RSVP Configuration Task List
- Specifying COPS Servers and Enabling COPS for RSVP
- Restricting RSVP Policy to Specific Access Control Lists
- Rejecting Unmatched RSVP Messages
- Confining Policy to PATH and RESV Messages
- Retaining RSVP Information After Losing Connection with the COPS Server
- Reporting the Results of Outsourcing and Configuration Decisions
- Verifying the Configuration
- COPS for RSVP Configuration Examples
Configuring COPS for RSVP
This chapter describes the tasks for configuring the COPS for RSVP feature. Common Open Policy Service (COPS) is a protocol for communicating network traffic policy information to network devices. Resource Reservation Protocol (RSVP) is a means for reserving network resources--primarily bandwidth--to guarantee that applications sending end-to-end across the Internet will perform at the desired speed and quality.
For complete conceptual information, see the "Signalling Overview" in this book.
For a complete description of the COPS for RSVP commands in this chapter, refer to the Cisco IOS Quality of Service Solutions Command Reference. To locate documentation of other commands that appear in this chapter, use the command reference master index, or search online.
Finding Support Information for Platforms and Cisco IOS and Catalyst OS Software Images
Use Cisco Feature Navigator to find information about platform support and Cisco IOS and Catalyst OS software image support. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn . An account on Cisco.com is not required.
Finding Feature Information
Your software release may not support all the features documented in this module. For the latest feature information and caveats, see the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the Feature Information Table at the end of this document.
Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.
COPS for RSVP Configuration Task List
To configure COPS for RSVP, perform the tasks described in the following sections.
- Specifying COPS Servers and Enabling COPS for RSVP
- Restricting RSVP Policy to Specific Access Control Lists
- Rejecting Unmatched RSVP Messages
- Confining Policy to PATH and RESV Messages
- Retaining RSVP Information After Losing Connection with the COPS Server
- Reporting the Results of Outsourcing and Configuration Decisions
- Verifying the Configuration
Specifying COPS Servers and Enabling COPS for RSVP
To specify COPS servers and enable COPS for RSVP, use the following commands beginning in interface configuration mode:
DETAILED STEPS
| Command or Action | Purpose | |
|---|---|---|
|
|
|
Enters global configuration mode. |
|
|
|
Tells the router to request RSVP policy decisions from the first server listed, and if that fails to connect, from the next server listed. Also enables a COPS-RSVP client on the router. |
Restricting RSVP Policy to Specific Access Control Lists
To restrict RSVP policy to specific access control lists (ACLs), use the following commands beginning in interface configuration mode:
DETAILED STEPS
| Command or Action | Purpose | |
|---|---|---|
|
|
|
Enters global configuration mode. |
|
|
|
Tells the router to apply RSVP policy to messages that match ACLs 40 and 160, and specifies the servers for those sessions. |
Rejecting Unmatched RSVP Messages
To reject unmatched RSVP messages, use the following commands beginning in interface configuration mode:
DETAILED STEPS
| Command or Action | Purpose | |
|---|---|---|
|
|
|
Enters global configuration mode. |
|
|
|
Tells the router to reject unmatched PATH and RESV messages, instead of just letting them pass through unadjudicated. |
Confining Policy to PATH and RESV Messages
To confine policy to PATH and RESV messages, use the following commands beginning in interface configuration mode:
DETAILED STEPS
| Command or Action | Purpose | |
|---|---|---|
|
|
|
Enters global configuration mode. |
|
|
|
Tells the router to adjudicate only PATH and RESV messages, and to accept and pass onward PATH ERROR, RESV ERROR, and RESV CONFIRM messages. |
Retaining RSVP Information After Losing Connection with the COPS Server
To retain RSVP information after losing connection with the COPS server, use the following commands beginning in interface configuration mode:
DETAILED STEPS
| Command or Action | Purpose | |
|---|---|---|
|
|
|
Enters global configuration mode. |
|
|
|
Tells the router to hold policy information for 10 minutes (600 seconds) while attempting to reconnect to a COPS server. |
Reporting the Results of Outsourcing and Configuration Decisions
To report the results of outsourcing and configuration decisions, use the following commands beginning in interface configuration mode:
DETAILED STEPS
| Command or Action | Purpose | |
|---|---|---|
|
|
|
Enters global configuration mode. |
|
|
|
Tells the router to report to the Policy Decision Point (PDP) the success or failure of outsourcing and configuration decisions. |
Verifying the Configuration
To verify the COPS for RSVP configuration, use the following commands in EXEC mode, as needed:
| Command |
Purpose |
|---|---|
Router# show cops servers |
Displays server addresses, port, state, keepalives, and policy client information. |
Router# show ip rsvp policy cops |
Displays policy server addresses, ACL IDs, and client/server connection status. |
Router# show ip rsvp policy |
Displays ACL IDs and their connection status. |
COPS for RSVP Configuration Examples
- Examples COPS Server Specified
- Example RSVP Behavior Customized
- Example Verification of the COPS for RSVP Configuration
Examples COPS Server Specified
The following example specifies the COPS server and enables COPS for RSVP on the server. Both of these functions are accomplished by using the ip rsvp policy cops command. By implication, the default settings for all remaining COPS for RSVP commands are accepted.
Router# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)# ip rsvp policy cops servers 161.44.130.168 161.44.129.6 Router(config)# exit
Example RSVP Behavior Customized
Once the COPS server has been specified and COPS for RSVP has been enabled, the remaining COPS for RSVP commands can be used to customize the COPS for RSVP behavior of the router. The following example uses the remaining COPS for RSVP commands to customize the RSVP behavior of the router:
Router# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)# ip rsvp policy cops 40 160 servers 161.44.130.168 161.44.129.6 Router(config)# ip rsvp policy default-reject Router(config)# ip rsvp policy cops minimal Router(config)# ip rsvp policy cops timeout 600 Router(config)# ip rsvp policy cops report-all Router(config)# exit
Example Verification of the COPS for RSVP Configuration
The following examples display three views of the COPS for RSVP configuration on the router, which can be used to verify the COPS for RSVP configuration.
This example displays the policy server address, state, keepalives, and policy client information:
Router# show cops servers
COPS SERVER: Address: 161.44.135.172. Port: 3288. State: 0. Keepalive: 120 sec
Number of clients: 1. Number of sessions: 1.
COPS CLIENT: Client type: 1. State: 0.
This example displays the policy server address, the ACL ID, and the client/server connection status:
Router# show ip rsvp policy cops
COPS/RSVP entry. ACLs: 40 60
PDPs: 161.44.135.172
Current state: Connected
Currently connected to PDP 161.44.135.172, port 0
This example displays the ACL ID numbers and the status for each ACL ID:
Router# show ip rsvp policy
Local policy: Currently unsupported
COPS:
ACLs: 40 60 . State: CONNECTED.
ACLs: 40 160 . State: CONNECTING.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.
Feedback