The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
This module describes how to configure the Internet Key Exchange (IKE) protocol for basic IP Security (IPsec) Virtual Private Networks (VPNs). IKE is a key management protocol standard that is used in conjunction with the IPsec standard. IPsec is an IP security feature that provides robust authentication and encryption of IP packets.
IPsec can be configured without IKE, but IKE enhances IPsec by providing additional features, flexibility, and ease of configuration for the IPsec standard.
IKE is a hybrid protocol, that implements the Oakley key exchange and Skeme key exchange inside the Internet Security Association Key Management Protocol (ISAKMP) framework. (ISAKMP, Oakley, and Skeme are security protocols implemented by IKE.)
Your software release may not support all the features documented in this module. For the latest feature information and caveats, see the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the Feature Information Table at the end of this document.
Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.
Cisco implements the following standards:
The component technologies implemented for use by IKE include the following:
Cisco IOS software also implements Triple DES (168-bit) encryption, depending on the software versions available for a specific platform. Triple DES (3DES) is a strong form of encryption that allows sensitive information to be transmitted over untrusted networks. It enables customers, particularly in the finance industry, to utilize network-layer encryption.
![]() Note |
Cisco IOS images that have strong encryption (including, but not limited to, 56-bit data encryption feature sets) are subject to United States government export controls, and have a limited distribution. Images that are to be installed outside the United States require an export license. Customer orders might be denied or subject to delay because of United States government regulations. Contact your sales representative or distributor for more information, or send e-mail to export@cisco.com. |
IKE interoperates with the X.509v3 certificates, which are used with the IKE protocol when authentication requires public keys. This certificate support allows the protected network to scale by providing the equivalent of a digital ID card to each device. When two devices intend to communicate, they exchange digital certificates to prove their identity (thus removing the need to manually exchange public keys with each peer or to manually specify a shared key at each peer).
IKE automatically negotiates IPsec security associations (SAs) and enables IPsec secure communications without costly manual preconfiguration. Specifically, IKE provides the following benefits:
IKE has two phases of key negotiation: phase 1 and phase 2. Phase 1 negotiates a security association (a key) between two IKE peers. The key negotiated in phase 1 enables IKE peers to communicate securely in phase 2. During phase 2 negotiation, IKE establishes keys (security associations) for other applications, such as IPsec.
Phase 1 negotiation can occur using main mode or aggressive mode. Main mode tries to protect all information during the negotiation, meaning that no information is available to a potential attacker. When main mode is used, the identities of the two IKE peers are hidden. Although this mode of operation is very secure, it is relatively costly in terms of the time required to complete the negotiation. Aggressive mode takes less time to negotiate keys between peers; however, it gives up some of the security provided by main mode negotiation. For example, the identities of the two parties trying to establish a security association are exposed to an eavesdropper.
The two modes serve different purposes and have different strengths. Main mode is slower than aggressive mode, but main mode is more secure and more flexible because it can offer an IKE peer more security proposals than aggressive mode. Aggressive mode is less flexible and not as secure, but much faster.
In Cisco IOS software, the two modes are not configurable. The default action for IKE authentication (rsa-sig, rsa-encr, or preshared) is to initiate main mode; however, in cases where there is no corresponding information to initiate authentication, and there is a preshared key associated with the hostname of the peer, Cisco IOS software can initiate aggressive mode. Cisco IOS software will respond in aggressive mode to an IKE peer that initiates aggressive mode.
An IKE policy defines a combination of security parameters to be used during the IKE negotiation. You must create an IKE policy at each peer participating in the IKE exchange.
If you do not configure any IKE policies, your router will use the default policy, which is always set to the lowest priority and which contains the default value of each parameter.
Because IKE negotiations must be protected, each IKE negotiation begins by agreement of both peers on a common (shared) IKE policy. This policy states which security parameters will be used to protect subsequent IKE negotiations and mandates how the peers are authenticated.
After the two peers agree upon a policy, the security parameters of the policy are identified by an SA established at each peer, and these SAs apply to all subsequent IKE traffic during the negotiation.
You can configure multiple, prioritized policies on each peer--e ach with a different combination of parameter values. However, at least one of these policies must contain exactly the same encryption, hash, authentication, and Diffie-Hellman parameter values as one of the policies on the remote peer. For each policy that you create, you assign a unique priority (1 through 10,000, with 1 being the highest priority).
![]() Tip |
If you are interoperating with a device that supports only one of the values for a parameter, your choice is limited to the value supported by the other device. Aside from this limitation, there is often a trade-off between security and performance, and many of these parameter values represent such a trade-off. You should evaluate the level of security risks for your network and your tolerance for these risks. |
When the IKE negotiation begins, IKE searches for an IKE policy that is the same on both peers. The peer that initiates the negotiation will send all its policies to the remote peer, and the remote peer will try to find a match. The remote peer looks for a match by comparing its own highest priority policy against the policies received from the other peer. The remote peer checks each of its policies in order of its priority (highest priority first) until a match is found.
A match is made when both policies from the two peers contain the same encryption, hash, authentication, and Diffie-Hellman parameter values.
If a match is found, IKE will complete negotiation, and IPsec security associations will be created. If no acceptable match is found, IKE refuses negotiation and IPsec will not be established.
![]() Note |
The parameter values apply to the IKE negotiations after the IKE SA is established. Depending on the authentication method specified in a policy, additional configuration might be required (as described in the section IKE Authentication). If a peer's policy does not have the required companion configuration, the peer will not submit the policy when attempting to find a matching policy with the remote peer. |
IKE authentication consists of the following options and each authentication method requires additional configuration.
With RSA signatures, you can configure the peers to obtain certificates from a CA. (The CA must be properly configured to issue the certificates.) Using a CA can dramatically improve the manageability and scalability of your IPsec network. Additionally, RSA signature-based authentication uses only two public key operations, whereas RSA encryption uses four public key operations, making it costlier in terms of overall performance. To properly configure CA support, see the module "Deploying RSA Keys Within a PKI."
The certificates are used by each peer to exchange public keys securely. (RSA signatures requires that each peer has the public signature key of the remote peer.) When both peers have valid certificates, they will automatically exchange public keys with each other as part of any IKE negotiation in which RSA signatures are used.
You can also exchange the public keys manually, as described in the section "Configuring RSA Keys Manually for RSA Encrypted Nonces."
RSA signatures provide nonrepudiation for the IKE negotiation. And, you can prove to a third party after the fact that you did indeed have an IKE negotiation with the remote peer.
With RSA encrypted nonces, you must ensure that each peer has the public keys of the other peers.
Unlike RSA signatures, the RSA encrypted nonces method cannot use certificates to exchange public keys. Instead, you ensure that each peer has the other's public keys by one of the following methods:
RSA encrypted nonces provide repudiation for the IKE negotiation; however, unlike RSA signatures, you cannot prove to a third party that you had an IKE negotiation with the remote peer.
Preshared keys are clumsy to use if your secured network is large, and they do not scale well with a growing network. However, they do not require use of a CA, as do RSA signatures, and might be easier to set up in a small network with fewer than ten nodes. RSA signatures also can be considered more secure when compared with preshared key authentication.
![]() Note |
If RSA encryption is configured and signature mode is negotiated (and certificates are used for signature mode), the peer will request both signature and encryption keys. Basically, the router will request as many keys as the configuration will support. If RSA encryption is not configured, it will just request a signature key. |
You should set the ISAKMP identity for each peer that uses preshared keys in an IKE policy.
When two peers use IKE to establish IPsec SAs, each peer sends its identity to the remote peer. Each peer sends either its hostname or its IP address, depending on how you have set the ISAKMP identity of the router.
By default, a peer's ISAKMP identity is the IP address of the peer. If appropriate, you could change the identity to be the peer's hostname instead. As a general rule, set the identities of all peers the same way--either all peers should use their IP addresses or all peers should use their hostnames. If some peers use their hostnames and some peers use their IP addresses to identify themselves to each other, IKE negotiations could fail if the identity of a remote peer is not recognized and a Domain Name System (DNS) lookup is unable to resolve the identity.
A mask preshared key allows a group of remote users with the same level of authentication to share an IKE preshared key. The preshared key of the remote peer must match the preshared key of the local peer for IKE authentication to occur.
A m ask preshared key is usually distributed through a secure out-of-band channel. In a remote peer-to-local peer scenario, any remote peer with the IKE preshared key configured can establish IKE SAs with the local peer.
If you specify the mask keyword with the crypto isakmp key command, it is up to you to use a subnet address, which will allow more peers to share the same key. That is, the preshared key is no longer restricted to use between two users.
![]() Note |
Using 0.0.0.0 as a subnet address is not recommended because it encourages group preshared keys, which allow all peers to have the same group key, thereby reducing the security of your user authentication. |
Disabling Extended Authentication (Xauth) for static IPsec peers prevents the routers from being prompted for Xauth information--username and password.
Without the ability to disable Xauth, a user cannot select which peer on the same crypto map should use Xauth. That is, if a user has router-to-router IPsec on the same crypto map as a VPN-client-to-Cisco-IOS IPsec, both peers are prompted for a username and password. In addition, a remote static peer (a Cisco IOS router) cannot establish an IKE SA with the local Cisco IOS router. (Xauth is not an optional exchange, so if a peer does not respond to an Xauth request, the IKE SA is deleted.) Thus, the same interface cannot be used to terminate IPsec to VPN clients (that need Xauth) and to other Cisco IOS routers (that cannot respond to Xauth) unless this feature is implemented.
![]() Note |
Xauth can be disabled only if preshared keys are used as the authentication mechanism for the given crypto map. |
IKE mode configuration, as defined by the Internet Engineering Task Force (IETF), allows a gateway to download an IP address (and other network-level configuration) to the client as part of an IKE negotiation. Using this exchange, the gateway gives an IP address to the IKE client to be used as an "inner" IP address encapsulated under IPsec. This method provides a known IP address for the client that can be matched against IPsec policy.
To implement IPsec VPNs between remote access clients that have dynamic IP addresses and a corporate gateway, you have to dynamically administer scalable IPsec policy on the gateway once each client is authenticated. With IKE mode configuration, the gateway can set up a scalable policy for a very large set of clients regardless of the IP addresses of those clients.
There are two types of IKE mode configuration:
If you do not want IKE to be used with your IPsec implementation, you can disable it at all IPsec peers via the no crypto isakmp command, skip the rest of this chapter, and begin your IPsec VPN.
![]() Note |
If you disable IKE, you will have to manually specify all the IPsec SAs in the crypto maps at all peers, the IPsec SAs of the peers will never time out for a given IPsec session, the encryption keys will never change during IPsec sessions between the peers, anti-replay services will not be available between the peers, and public key infrastructure (PKI) support cannot be used. |
IKE is enabled by default. IKE does not have to be enabled for individual interfaces, but it is enabled globally for all interfaces at the router.
Perform the following tasks to provide authentication of IPsec peers, negotiate IPsec SAs, and establish IPsec keys:
Perform this task to create an IKE policy.
The following sample output from the show crypto isakmp policy command displays a warning message after a user tries to configure an IKE encryption method that the hardware does not support:
Router# show crypto isakmp policy
Protection suite of priority 1
encryption algorithm: AES - Advanced Encryption Standard (256 bit keys).
WARNING:encryption hardware does not support the configured
encryption method for ISAKMP policy 1
hash algorithm: Secure Hash Standard
authentication method: Pre-Shared Key
Diffie-Hellman group: #1 (768 bit)
lifetime: 3600 seconds, no volume limit
Using the clear crypto sa command without parameters will clear out the full SA database, which will clear out active security sessions. You may also specify the peer, map, or entry keywords to clear out only a subset of the SA database. For more information, see the clear crypto sa command in the Cisco IOS Security Command Reference.
If a user enters an IPsec transform or an IKE encryption method that the hardware does not support, a warning message will be generated. These warning messages are also generated at boot time. When an encrypted card is inserted, the current configuration is scanned. If any IPsec transforms or IKE encryption methods are found that are not supported by the hardware, a warning message will be generated.
Depending on which authentication method you specified in your IKE policies (RSA signatures, RSA encrypted nonces, or preshared keys), you must do certain additional configuration tasks before IKE and IPsec can successfully use the IKE policies. For information on completing these additional tasks, refer to the Configuring IKE Authentication."
To configure an AES-based transform set, see the module "Configuring Security for VPNs with IPsec."
After you have created at least one IKE policy in which you specified an authentication method (or accepted the default method), you need to configure an authentication method. IKE policies cannot be used by IPsec until the authentication method is successfully configured.
![]() Note |
Before configuring IKE authentication, you must have configured at least one IKE policy, which is where the authentication method was specified (or RSA signatures was accepted by default). |
To configure IKE authentication, you should perform one of the following tasks, as appropriate:
You must have configured at least one IKE policy, which is where the authentication method was specified (or RSA signatures was accepted by default).
![]() Note |
This task can be performed only if a CA is not in use. |
To manually configure RSA keys, perform this task for each IPsec peer that uses RSA encrypted nonces in an IKE policy.
Command or Action | Purpose | |||
---|---|---|---|---|
|
Example: Router> enable |
Enables privileged EXEC mode. |
||
|
Example: Router# configure terminal |
Enters global configuration mode. |
||
|
Example: Router(config)# crypto key generate rsa general-keys modulus 360 |
Generates RSA keys. |
||
|
Example: Router(config)# crypto key generate ec keysize 256 label Router_1_Key |
Generates EC keys.
|
||
|
Example: Router(config)# exit |
(Optional) Exits global configuration mode. |
||
|
Example: Router# show crypto key mypubkey rsa |
(Optional) Displays the generated RSA public keys. |
||
|
Example: Router# configure terminal |
Returns to global configuration mode. |
||
|
Example: Router(config)# crypto key pubkey-chain rsa |
Enters public key chain configuration mode (so you can manually specify the RSA public keys of other devices). |
||
|
Example: Router(config-pubkey-chain)# named-key otherpeer.example.com Example: Router(config-pubkey-chain)# addressed-key 10.1.1.2 encryption |
Indicates which remote peer's RSA public key you will specify and enters public key configuration mode.
|
||
|
Example: Router(config-pubkey-key)# address 10.5.5.1 |
Specifies the IP address of the remote peer. |
||
|
Example: Router(config-pubkey-key)# key-string Example: Router(config-pubkey)# 00302017 4A7D385B 1234EF29 335FC973 Example: Router(config-pubkey)# 2DD50A37 C4F4B0FD 9DADE748 429618D5 Example: Router(config-pubkey)# 18242BA3 2EDFBDD3 4296142A DDF7D3D8 Example: Router(config-pubkey)# 08407685 2F2190A0 0B43F1BD 9A8A26DB Example: Router(config-pubkey)# 07953829 791FCDE9 A98420F0 6A82045B Example: Router(config-pubkey)# 90288A26 DBC64468 7789F76E EE21 |
Specifies the RSA public key of the remote peer. |
||
|
Example: Router(config-pubkey-key)# quit |
Returns to public key chain configuration mode. |
||
|
|
-- |
||
|
Example: Router(config-pubkey-key)# exit |
Returns to global configuration mode. |
||
|
Example: Router(config)# exit |
Returns to privileged EXEC mode. |
||
|
Example: Router# show crypto key pubkey-chain rsa |
(Optional) Displays either a list of all RSA public keys that are stored on your router or details of a particular RSA key that is stored on your router. |
To configure preshared keys, perform these steps for each peer that uses preshared keys in an IKE policy.
![]() Note |
Preshared keys do not scale well with a growing network. Mask preshared keys have the following restrictions:
|
Command or Action | Purpose | |||
---|---|---|---|---|
|
Example: Router> enable |
Enables privileged EXEC mode. |
||
|
Example: Router# configure terminal |
Enters global configuration mode. |
||
|
Example: Router(config)# crypto isakmp identity address |
Specifies the peer's ISAKMP identity by IP address, by distinguished name (DN) hostname at the local peer.
|
||
|
Example: Router(config)# ip host RemoteRouter.example.com 192.168.0.1 |
If the local peer's ISAKMP identity was specified using a hostname, maps the peer's host name to its IP address(es) at all the remote peers. (This step might be unnecessary if the hostname or address is already mapped in a DNS server.) |
||
|
Example: Router(config)# crypto isakmp key sharedkeystring address 192.168.1.33 no-xauth Example: Router(config) crypto isakmp key sharedkeystring hostname RemoteRouter.example.com |
Specifies at the local peer the shared key to be used with a particular remote peer.
|
||
|
Example: Router(config) crypto isakmp key sharedkeystring address 10.0.0.1 Example: Router(config) crypto isakmp key sharedkeystring hostname LocalRouter.example.com |
Specifies at the remote peer the shared key to be used with the local peer. |
||
|
|
-- |
![]() Note |
IKE mode configuration has the following restrictions:
|
Command or Action | Purpose | |
---|---|---|
|
Example: Router> enable |
Enables privileged EXEC mode. |
|
Example: Router# configure terminal |
Enters global configuration mode. |
|
Example: Router(config)# ip local pool pool1 172.16.23.0 172.16.23.255 |
Defines an existing local address pool that defines a set of addresses. |
|
Example: Router(config)# crypto isakmp client configuration address-pool local pool1 |
References the local address pool in the IKE configuration. |
|
Example: Router(config)# crypto map dyn client configuration address initiate |
Configures IKE mode configuration in global configuration mode. |
Command or Action | Purpose | |
---|---|---|
|
Example: Router> enable |
Enables privileged EXEC mode.
|
|
Example: Router# configure terminal |
Enters global configuration mode. |
|
Example: Router(config)# crypto map example 1 ipsec-ipsec-isakmp |
Specifies the crypto map and enters crypto map configuration mode.
|
|
Example: Router(config-isakmp)# set pfs 14 |
Specifies the DH group identifier for IPSec SA negotiation.
The group chosen must be strong enough (have enough bits) to protect the IPsec keys during negotiation. A generally accepted guideline recommends the use of a 2048-bit group after 2013 (until 2030). Either group 14 can be selected to meet this guideline. Even if a longer-lived security method is needed, the use of Elliptic Curve Cryptography is recommended, but group 15 and group 16 can also be considered. |
This section contains the following examples, which show how to configure a 3DES IKE policy and an AES IKE policy:
This example creates two IKE policies, with policy 15 as the highest priority, policy 20 as the next priority, and the existing default priority as the lowest priority. It also creates a preshared key to be used with policy 20 with the remote peer whose IP address is 192.168.224.33.
crypto isakmp policy 15 encryption 3des hash md5 authentication rsa-sig group 2 lifetime 5000 ! crypto isakmp policy 20 authentication pre-share lifetime 10000 ! crypto isakmp key 1234567890 address 192.168.224.33
In the example, the encryption DES of policy default would not appear in the written configuration because this is the default value for the encryption algorithm parameter.
If the show crypto isakmp policycommand is issued with this configuration, the output is as follows:
Protection suite priority 15 encryption algorithm:3DES - Triple Data Encryption Standard (168 bit keys) hash algorithm:Message Digest 5 authentication method:Rivest-Shamir-Adleman Signature Diffie-Hellman group:#2 (1024 bit) lifetime:5000 seconds, no volume limit Protection suite priority 20 encryption algorithm:DES - Data Encryption Standard (56 bit keys) hash algorithm:Secure Hash Standard authentication method:preshared Key Diffie-Hellman group:#1 (768 bit) lifetime:10000 seconds, no volume limit Default protection suite encryption algorithm:DES - Data Encryption Standard (56 bit keys) hash algorithm:Secure Hash Standard authentication method:Rivest-Shamir-Adleman Signature Diffie-Hellman group:#1 (768 bit) lifetime:86400 seconds, no volume limit
Note that although the output shows "no volume limit" for the lifetimes, you can configure only a time lifetime (such as 86,400 seconds); volume-limit lifetimes are not configurable.
The following example is sample output from the show running-configcommand. In this example, the AES 256-bit key is enabled.
Current configuration : 1665 bytes ! version 12.2 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname "Router1" ! ! ip subnet-zero ! ! no ip domain lookup ! ip audit notify log ip audit po max-events 100 ! crypto isakmp policy 10 encryption aes 256 authentication pre-share lifetime 180 crypto isakmp key cisco123 address 10.0.110.1 ! ! crypto ipsec transform-set aesset esp-aes 256 esp-sha-hmac mode transport ! crypto map aesmap 10 ipsec-isakmp set peer 10.0.110.1 set transform-set aesset match address 120 ! . . .
The following example shows how to manually specify the RSA public keys of two IPsec peer-- the peer at 10.5.5.1 uses general-purpose keys, and the other peer uses special-usage keys:
crypto key pubkey-chain rsa named-key otherpeer.example.com address 10.5.5.1 key-string 005C300D 06092A86 4886F70D 01010105 00034B00 30480241 00C5E23B 55D6AB22 04AEF1BA A54028A6 9ACC01C5 129D99E4 64CAB820 847EDAD9 DF0B4E4C 73A05DD2 BD62A8A9 FA603DD2 E2A8A6F8 98F76E28 D58AD221 B583D7A4 71020301 0001 quit exit addressed-key 10.1.1.2 encryption key-string 00302017 4A7D385B 1234EF29 335FC973 2DD50A37 C4F4B0FD 9DADE748 429618D5 18242BA3 2EDFBDD3 4296142A DDF7D3D8 08407685 2F2190A0 0B43F1BD 9A8A26DB 07953829 791FCDE9 A98420F0 6A82045B 90288A26 DBC64468 7789F76E EE21 quit exit addressed-key 10.1.1.2 signature key-string 0738BC7A 2BC3E9F0 679B00FE 53987BCC 01030201 42DD06AF E228D24C 458AD228 58BB5DDD F4836401 2A2D7163 219F882E 64CE69D4 B583748A 241BED0F 6E7F2F16 0DE0986E DF02031F 4B0B0912 F68200C4 C625C389 0BFF3321 A2598935 C1B1 quit exit exit
After you have successfully configured IKE negotiation, you can begin configuring IPsec. For information on completing these tasks, see the module "Configuring Security for VPNs With IPsec."
Related Topic |
Document Title |
---|---|
Cisco IOS commands |
|
Security commands: complete command syntax, command mode, command history, defaults, usage guidelines, and examples |
|
IPsec configuration |
|
IKE Version 2 |
|
Configuring RSA keys to obtain certificates from a CA |
|
Suite-B ESP transforms |
|
Suite-B Integrity algorithm type transform configuration. |
|
Suite-B Elliptic curve Diffie-Hellman (ECDH) support for IPsec SA negotiation |
|
Suite-B support for certificate enrollment for a PKI |
Standards |
Title |
---|---|
None |
-- |
MIBs |
MIBs Link |
---|---|
None |
To locate and download MIBs for selected platforms, Cisco IOS software releases, and feature sets, use Cisco MIB Locator found at the following URL: |
RFCs |
Title |
---|---|
RFC 2408 |
Internet Security Association and Key Management Protocol (ISAKMP) |
RFC 2409 |
The Internet Key Exchange (IKE) |
RFC 2412 |
Description |
Link |
---|---|
The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password. |
The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.
Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.
Table 1 | Feature Information for Configuring IKE for IPsec VPNs |
Feature Name |
Releases |
Feature Information |
---|---|---|
Ability to Disable Extended Authentication for Static IPsec Peers |
12.2(4)T |
This feature allows a user to disable Xauth while configuring the preshared key for router-to-router IPsec. Thus, the router will not prompt the peer for a username and password, which are transmitted when Xauth occurs for VPN-client-to-Cisco-IOS IPsec. The following command was modified by this feature: crypto isakmp key. |
Advanced Encryption Standard (AES) |
12.2(8)T |
This feature adds support for the new encryption standard AES, which is a privacy transform for IPsec and IKE and has been developed to replace DES. The following commands were modified by this feature: crypto ipsec transform-set, encryption (IKE policy), show crypto ipsec transform-set, crypto ipsec transform-set, show crypto isakmp policy. |
SEAL Encryption |
12.3(7)T |
This feature adds support for SEAL encryption in IPsec. The following command was modified by this feature: crypto ipsec transform-set. |
Suite-B support in IOS SW crypto |
15.1(2)T |
Suite-B adds support in the Cisco IOS for the SHA-2 family (HMAC variant) hash algorithm used to authenticate packet data and verify the integrity verification mechanisms for the IKE protocol. HMAC is a variant that provides an additional level of hashing. This feature also adds elliptic curve Diffie-Hellman (ECDH) support for IPsec SA negotiation. See the Configuring Security for VPNs with IPsec feature module for more detailed information about Cisco IOS Suite-B support. The following command was modified by this feature: authentication, crypto key generate ec keysize, crypto map, group, hash, set pfs. |
Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1005R)
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.