Real-Time Resolution for IPsec Tunnel Peer

After a user specifies a host name (instead of an IP address) for remote IP Security (IPsec) peer, the Real-Time Resolution for IPsec Tunnel Peer feature allows the host name to be domain name server (DNS) resolved before the router establishes the IPsec tunnel. Thus, the router can immediately discover whether the IP address of the peer has changed.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

Restrictions for Real-Time Resolution for IPsec Tunnel Peer

Secure DNS Requirement

It is recommended that you use this feature only with secure DNS and when the DNS responses can be authenticated. Otherwise, an attacker can spoof or forge DNS responses and have access to Internet Key Exchange (IKE) authentication data, such as a certificate. If an attacker has a certificate that is trusted by the initiating host, the attacker can successfully establish Phase 1 IKE security association (SA), or the attacker can try to guess the preshared key that is shared between the initiator and the actual responder.

DNS Initiator

DNS names resolution for remote IPsec peers will work only if they are used as an initiator. The first packet that is to be encrypted will trigger a DNS lookup; after the DNS lookup is complete, subsequent packets will trigger IKE.

Information About Real-Time Resolution for IPsec Tunnel Peer

Real-Time Resolution Via Secure DNS

When specifying the host name of a remote IPsec peer via the set peer command, you can also issue the dynamic keyword, which defers DNS resolution of the host name until right before the IPsec tunnel has been established. Deferring resolution enables the software to detect whether the IP address of the remote IPsec peer has changed. Thus, the software can contact the peer at the new IP address.

If the dynamic keyword is not issued, the host name is resolved immediately after it is specified. So, the software cannot detect an IP address change and, therefore, attempts to connect to the IP address that it previously resolved.

DNS resolution assures users that their established IPsec tunnel is secure and authenticated.

How to Configure Real-Time Resolution

Configuring Real-Time Resolution for IPsec Peers

Use this task to configure a router to perform real-time DNS resolution with a remote IPsec peer; that is, the host name of peer is resolved via a DNS lookup right before the router establishes a connection (an IPsec tunnel) with the peer.

Before You Begin

Before creating a crypto map, you should perform the following tasks:

  • Define Internet Security Association Key Management Protocol (ISAKMP) policies.

  • Define IPsec transform sets.

SUMMARY STEPS

    1.    enable

    2.    configure terminal

    3.    crypto map map-name seq-num ipsec-isakmp

    4.    match address access-list-id

    5.    set peer {host-name [dynamic] | ip-address

    6.    set transform-set transform-set-name1 [transform-set-name2 ... transform-set-name6]


DETAILED STEPS
     Command or ActionPurpose
    Step 1 enable


    Example:
    Router> enable
     

    Enables privileged EXEC mode.

    • Enter your password if prompted.

     
    Step 2 configure terminal


    Example:
    Router# configure terminal
     

    Enters global configuration mode.

     
    Step 3 crypto map map-name seq-num ipsec-isakmp


    Example:
    Router(config)# crypto map secure_b 10 ipsec-isakmp
     

    Specifies the crypto map entry to create (or modify) and enters crypto map configuration mode.

     
    Step 4 match address access-list-id


    Example:
    Router(config-crypto-m)# match address 140
     

    Names an extended access list.

    This access list determines which traffic should be protected by IPsec and which traffic should not be protected by IPsec in the context of this crypto map entry.

     
    Step 5 set peer {host-name [dynamic] | ip-address


    Example:
    Router(config-crypto-m)#
 set peer b.cisco.com dynamic
     

    Specifies a remote IPsec peer.

    This is the peer to which IPsec-protected traffic can be forwarded.

    • dynamic --Allows the host name to be resolved via a DNS lookup just before the router establishes the IPsec tunnel with the remote peer. If this keyword is not specified, the host name will be resolved immediately after the host name is specified.

    Repeat for multiple remote peers.

     
    Step 6 set transform-set transform-set-name1 [transform-set-name2 ... transform-set-name6]


    Example:
    Router(config-crypto-m)# set transform-set myset
     

    Specifies which transform sets are allowed for this crypto map entry. List multiple transform sets in order of priority (highest priority first).

     

    Troubleshooting Tips

    To display crypto map configuration information, use the show crypto map command.

    What to Do Next

    You need to apply a crypto map set to each interface through which IPsec traffic will flow. Applying the crypto map set to an interface instructs the router to evaluate all the interface’s traffic against the crypto map set and to use the specified policy during connection or security association (SA) negotiation on behalf of traffic to be protected by crypto.

    Configuration Examples for Real-Time Resolution

    Configuring Real-Time Resolution for an IPsec Peer Example

    The figure below and the following example illustrate how to create a crypto map that configures the host name of a remote IPsec peer to DNS resolved via a DNS lookup right before the software attempts to establish a connection with that peer.

    Figure 1. Real-Time Resolution Sample Topology

    ! Configure the initiating router.
hostname a.cisco.com
ip domain name cisco.com
ip name server 10.0.0.1 
! 
crypto map secure_b 10 ipsec-isakmp
  match address 140
  set peer b.cisco.com dynamic 
  set transform-set xset
interface serial1
  ip address 10.10.0.1
  crypto map secure_b
access-list 140 permit ...
!
! Configure the responding router (the remote IPSec peer).
hostname b.cisco.com
!
crypto map secure_a 10 ipsec-isakmp
  match address 150
  set peer 10.10.0.1
  set transform-set
interface serial0/1
  ip address 10.0.0.1
  crypto map secure_a
access-list 150 ...
! DNS server configuration
b.cisco.com 10.0.0.1       # the address of serial0/1 of b.cisco.com

    Additional References

    Related Documents

    Related Topic

    Document Title

    Crypto maps

    “Configuring Security for VPNs with IPsec” module in the Security for VPNs with IPsec Configuration Guide

    ISAKMP policies

    “Configuring Internet Key Exchange for IPsec VPNs” module in the Internet Key Exchange for IPsec VPNs Configuration Guide

    IPsec and IKE configuration commands

    Cisco IOS Security Command Reference

    Standards

    Standards

    Title

    No new or modified standards are supported by this feature, and support for existing standards has not been modified by this feature

    --

    MIBs

    MIBs

    MIBs Link

    No new or modified MIBs are supported by this feature, and support for existing MIBs has not been modified by this feature.

    To locate and download MIBs for selected platforms, Cisco IOS XE software releases, and feature sets, use Cisco MIB Locator found at the following URL:

    http:/​/​www.cisco.com/​go/​mibs

    RFCs

    RFCs

    Title

    No new or modified RFCs are supported by this feature, and support for existing RFCs has not been modified by this feature.

    --

    Technical Assistance

    Description

    Link

    The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies.

    To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds.

    Access to most tools on the Cisco Support website requires a Cisco.com user ID and password.

    http:/​/​www.cisco.com/​techsupport

    Feature Information for Real-Time Resolution for IPsec Tunnel Peer

    The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

    Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.
    Table 1 Feature Information for Real-Time Resolution for IPsec Tunnel Peer

    Feature Name

    Releases

    Feature Information

    Real-Time Resolution for IPsec Tunnel Peer

    Cisco IOS XE Release 2.1

    After a user specifies a host name (instead of an IP address) for remote IP Security (IPsec) peer, this feature allows the host name to be domain name server (DNS) resolved before the router establishes the IPsec tunnel. Thus, the router can immediately discover whether the IP address of the peer has changed.

    The following commands were introduced or modified: set peer (IPsec).