- IP Access List Overview
- Access Control List Overview and Guidelines
- Creating an IP Access List and Applying It to an Interface
- Creating an IP Access List to Filter IP Options, TCP Flags, Noncontiguous Ports
- ACL Syslog Correlation
- Refining an IP Access List
- IP Access List Entry Sequence Numbering
- Displaying and Clearing IP Access List Data Using ACL Manageability
- Object Groups for ACLs
- Controlling Access to a Virtual Terminal Line
- Access List-Based RBSCP
- ACL IP Options Selective Drop
- ACL Authentication of Incoming rsh and rcp Requests
- Configuring Lock-and-Key Security (Dynamic Access Lists)
- Configuring IP Session Filtering (Reflexive Access Lists)
- IPv6 Access Control Lists
- IPv6 ACL Extensions for Hop by Hop Filtering
- ACL: Hardware and Software Counters Granularity for IPv4 and IPv6 ACL Statistics
- IPv6 PACL Support
- Finding Feature Information
- Prerequisites for Creating an IP Access List and Applying It to an Interface
- Information About Creating an IP Access List and Applying It to an Interface
- How to Create an IP Access List and Apply It to an Interface
- Example Filtering on Source Address (Hosts)
- Example Filtering on Source Address (Subnet)
- Example Filtering on Source Address Destination Address and IP Protocols
- Example Filtering on Source Address (Host and Subnets) Using a Numbered Access List
- Example Preventing Telnet Access to a Subnet
- Example Filtering on TCP and ICMP Using Port Numbers
- Example Allowing SMTP (E-mail) and Established TCP Connections
- Example Preventing Access to the Web By Filtering on Port Name
- Example Filtering on Source Address and Logging the Packets Permitted and Denied
- Example: Limiting Debug Output
Creating an IP Access List and Applying It to an Interface
IP access lists provide many benefits for securing a network and achieving nonsecurity goals, such as determining quality of service (QoS) factors or limiting debug command output. This module describes how to create standard, extended, named, and numbered IP access lists. An access list can be referenced by a name or a number. Standard access lists filter on only the source address in IP packets. Extended access lists can filter on source address, destination address, and other fields in an IP packet.
After you create an access list, you must apply it to something in order for it to have any effect. This module describes how to apply an access list to an interface. However, there are many other uses for an access list, which are referenced in this module and described in other modules and in other configuration guides for various technologies.
- Finding Feature Information
- Prerequisites for Creating an IP Access List and Applying It to an Interface
- Information About Creating an IP Access List and Applying It to an Interface
- How to Create an IP Access List and Apply It to an Interface
- Configuration Examples for Creating an IP Access List and Applying It to an Interface
- Where to Go Next
- Additional References for Creating an IP Access List to Filter TCP Flags
- Feature Information for Creating an IP Access List and Applying It to an Interface
Finding Feature Information
Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table.
Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.
Prerequisites for Creating an IP Access List and Applying It to an Interface
Before you create or apply an IP access list, you should understand the concepts in the “IP Access List Overview” module. You should also have IP running in your network.
Information About Creating an IP Access List and Applying It to an Interface
Helpful Hints for Creating IP Access Lists
The following tips will help you avoid unintended consequences and help you create more efficient access lists.
Create the access list before applying it to an interface (or elsewhere), because if you apply a nonexistent access list to an interface and then proceed to configure the access list, the first statement is put into effect, and the implicit deny statement that follows could cause you immediate access problems.
Another reason to configure an access list before applying it is because an interface with an empty access list applied to it permits all traffic.
All access lists need at least one permit statement; otherwise, all packets are denied and no traffic passes.
Because the software stops testing conditions after it encounters the first match (to either a permit or deny statement), you will reduce processing time and resources if you put the statements that packets are most likely to match at the beginning of the access list. Place more frequently occurring conditions before less frequent conditions.
Organize your access list so that more specific references in a network or subnet appear before more general ones.
Use the statement permit any any if you want to allow all other packets not already denied. Using the statement permit any any in effect avoids denying all other packets with the implicit deny statement at the end of an access list. Do not make your first access list entry permit any any because all traffic will get through; no packets will reach the subsequent testing. In fact, once you specify permit any any, all traffic not already denied will get through.
Although all access lists end with an implicit deny statement, we recommend use of an explicit deny statement (for example, deny ip any any). On most platforms, you can display the count of packets denied by issuing the show access-listcommand, thus finding out more information about who your access list is disallowing. Only packets denied by explicit deny statements are counted, which is why the explicit deny statement will yield more complete data for you.
While you are creating an access list or after it is created, you might want to delete an entry. - You cannot delete an entry from a numbered access list; trying to do so will delete the entire access list. If you need to delete an entry, you need to delete the entire access list and start over.
- You can delete an entry from a named access list. Use the no permitor no deny command to delete the appropriate entry.
In order to make the purpose of individual statements more scannable and easily understood at a glance, you can write a helpful remark before or after any statement by using the remark command.
If you want to deny access to a particular host or network and find out if someone from that network or host is attempting to gain access, include the log keyword with the corresponding deny statement so that the packets denied from that source are logged for you.
This hint applies to the placement of your access list. When trying to save resources, remember that an inbound access list applies the filter conditions before the routing table lookup. An outbound access list applies the filter conditions after the routing table lookup.
Access List Remarks
You can include comments or remarks about entries in any IP access list. An access list remark is an optional remark before or after an access list entry that describes the entry so that you do not have to interpret the purpose of the entry. Each remark is limited to 100 characters in length.
The remark can go before or after a permit or deny statement. Be consistent about where you add remarks. Users may be confused if some remarks precede the associated permit or deny statements and some remarks follow the associated statements.
The following is an example of a remark that describes function of the subsequent deny statement:
ip access-list extended telnetting remark Do not allow host1 subnet to telnet out deny tcp host 172.16.2.88 any eq telnet
Additional IP Access List Features
Beyond the basic steps to create a standard or extended access list, you can enhance your access lists as mentioned below. Each of these methods is described completely in the Refining an IP Access List module.
-
You can impose dates and times when permit or deny statements in an extended access list are in effect, making your access list more granular and specific to an absolute or periodic time period.
-
After you create a named or numbered access list, you might want to add entries or change the order of the entries, known as resequencing an access list.
-
You can achieve finer granularity when filtering packets by filtering on noninitial fragments of packets.
How to Create an IP Access List and Apply It to an Interface
This section describes the general ways to create a standard or extended access list using either a name or a number. Access lists are very flexible; the tasks simply illustrate one permit command and one deny command to provide you the command syntax of each. Only you can determine how many permit and deny commands you need and their order.
 Note | The first two tasks in this module create an access list; you must apply the access list in order for it to function. If you want to apply the access list to an interface, perform the task "Applying the Access List to an Interface". If you don’t intend to apply the access list to an interface, see the "Where to Go Next" for pointers to modules that describe other ways to apply access lists. |
- Creating a Standard Access List to Filter on Source Address
- Creating an Extended Access List
- Applying the Access List to an Interface
Creating a Standard Access List to Filter on Source Address
If you want to filter on source address only, a standard access list is simple and sufficient. There are two alternative types of standard access list: named and numbered. Named access lists allow you to identify your access lists with a more intuitive name rather than a number, and they also support more features than numbered access lists.
- Creating a Named Access List to Filter on Source Address
- What to Do Next
- Creating a Numbered Access List to Filter on Source Address
- What to Do Next
Creating a Named Access List to Filter on Source Address
Use a standard, named access list if you need to filter on source address only. This task illustrates one permit statement and one deny statement, but the actual statements you use and their order depend on what you want to filter or allow. Define your permit and deny statements in the order that achieves your filtering goals.
1.
enable
2.
configure
terminal
3.
ip
access-list
standard
name
4.
remark
remark
5. deny {source [source-wildcard] | any} [log]
6.
remark
remark
7.
permit
{source
[source-wildcard] |
any} [log]
8. Repeat some combination of Steps 4 through 7 until you have specified the sources on which you want to base your access list.
9.
end
10.
show
ip
access-list
DETAILED STEPS
What to Do Next
The access list you created is not in effect until you apply it to an interface, a vty line, or reference it from a command that uses an access list. See "Applying the Access List to an Interface" or "Where to Go Next" for pointers to modules that describe other ways to use access lists.
Creating a Numbered Access List to Filter on Source Address
Configure a standard, numbered access list if you need to filter on source address only and you prefer not to use a named access list.
IP standard access lists are numbered 1 to 99 or 1300 to 1999. This task illustrates one permit statement and one deny statement, but the actual statements you use and their order depend on what you want to filter or allow. Define your permit and deny statements in the order that achieves your filtering goals.
1.
enable
2.
configure
terminal
3.
access-list
access-list-number
permit {source [source-wildcard] |
any} [log]
4.
access-list
access-list-number
deny {source [source-wildcard] |
any} [log]
5. Repeat some combination of Steps 3 through 6 until you have specified the sources on which you want to base your access list.
6.
end
7.
show
ip
access-list
DETAILED STEPS
What to Do Next
The access list you created is not in effect until you apply it to an interface, a vty line, or reference it from a command that uses an access list. See "Applying the Access List to an Interface" or "Where to Go Next" for pointers to modules that describe other ways to use access lists.
Creating an Extended Access List
If you want to filter on anything other than source address, you need to create an extended access list. There are two alternative types of extended access list: named and numbered. Named access lists allow you to identify your access lists with a more intuitive name rather than a number, and they also support more features.
For details on how to filter something other than source or destination address, see the syntax descriptions in the command reference documentation.
Creating a Named Extended Access List
Create a named extended access list if you want to filter on source and destination address, or a combination of addresses and other IP fields.
1.
enable
2.
configure
terminal
3.
ip
access-list
extended
name
4.
remark
remark
5.
deny
protocol
source
[source-wildcard]
destination
[destination-wildcard]
[option
option-name]
[precedence
precedence] [tos
tos]
[established] [log |
log-input]
[time-range
time-range-name]
[fragments]
6.
remark
remark
7.
permit
protocol
source
[source-wildcard]
destination
[destination-wildcard]
[option
option-name]
[precedence
precedence] [tos
tos]
[established] [log |
log-input]
[time-range
time-range-name]
[fragments]
8. Repeat some combination of Steps 4 through 7 until you have specified the fields and values on which you want to base your access list.
9.
end
10.
show
ip
access-list
DETAILED STEPS
What to Do Next
The access list you created is not in effect until you apply it to an interface, a vty line, or reference it from a command that uses an access list. See "Applying the Access List to an Interface" or the "Where to Go Next" for pointers to modules that describe other ways to use access lists.
Creating a Numbered Extended Access List
Create a numbered extended access list if you want to filter on source and destination address, or a combination of addresses and other IP fields, and you prefer not to use a name. Extended IP access lists are numbered 100 to 199 or 2000 to 2699.
1.
enable
2.
configure
terminal
3.
access-list
access-list-number
remark
remark
4.
access-list
access-list-number
permit
protocol
{source [source-wildcard] | any} {destination [destination-wildcard] | any} [precedence precedence] [tos tos] [established] [log | log-input] [time-range time-range-name] [fragments]
5.
access-list
access-list-number
remark
remark
6.
access-list
access-list-number
deny
protocol
{source [source-wildcard] | any} {destination [destination-wildcard] | any} [precedence precedence] [tos tos] [established] [log | log-input] [time-range time-range-name] [fragments]
7. Repeat some combination of Steps 3 through 6 until you have specified the fields and values on which you want to base your access list.
8.
end
9.
show
ip
access-list
DETAILED STEPS
Applying the Access List to an Interface
Perform this task to apply an access list to an interface.
1.
enable
2.
configure
terminal
3.
interface
type
number
4.
ip
access-group
{access-list-number | access-list-name} {in | out}
DETAILED STEPS
What to Do Next
The access list you created is not in effect until you apply it to an interface, a vty line, or reference it from a command that uses an access list. See "Applying the Access List to an Interface" or "Where to Go Next" for pointers to modules that describe other ways to use access lists.
Configuration Examples for Creating an IP Access List and Applying It to an Interface
- Example Filtering on Source Address (Hosts)
- Example Filtering on Source Address (Subnet)
- Example Filtering on Source Address Destination Address and IP Protocols
- Example Filtering on Source Address (Host and Subnets) Using a Numbered Access List
- Example Preventing Telnet Access to a Subnet
- Example Filtering on TCP and ICMP Using Port Numbers
- Example Allowing SMTP (E-mail) and Established TCP Connections
- Example Preventing Access to the Web By Filtering on Port Name
- Example Filtering on Source Address and Logging the Packets Permitted and Denied
- Example: Limiting Debug Output
Example Filtering on Source Address (Hosts)
In the following example, the workstation belonging to Jones is allowed access to Ethernet interface 0 and the workstation belonging to Smith is not allowed access:
interface ethernet 0 ip access-group workstations in ! ip access-list standard workstations remark Permit only Jones workstation through permit 172.16.2.88 remark Do not allow Smith workstation through deny 172.16.3.13
Example Filtering on Source Address (Subnet)
In the following example, the Jones subnet is not allowed access to Ethernet interface 0, but the Main subnet is allowed access:
interface ethernet 0 ip access-group prevention in ! ip access-list standard prevention remark Do not allow Jones subnet through deny 172.22.0.0 0.0.255.255 remark Allow Main subnet permit 172.25.0.0 0.0.255.255
Example Filtering on Source Address Destination Address and IP Protocols
The following configuration example shows an interface with two access lists, one applied to outgoing packets and one applied to incoming packets. The standard access list named Internet_filter filters outgoing packets on source address. The only packets allowed out the interface must be from source 172.16.3.4.
The extended access list named marketing_group filters incoming packets. The access list permits Telnet packets from any source to network 172.26.0.0 and denies all other TCP packets. It permits any ICMP packets. It denies UDP packets from any source to network 172.26.0 0 on port numbers less than 1024. Finally, the access list denies all other IP packets and performs logging of packets passed or denied by that entry.
interface Ethernet0/5 ip address 172.20.5.1 255.255.255.0 ip access-group Internet_filter out ip access-group marketing_group in ! ip access-list standard Internet_filter permit 172.16.3.4 ip access-list extended marketing_group permit tcp any 172.26.0.0 0.0.255.255 eq telnet deny tcp any any permit icmp any any deny udp any 172.26.0.0 0.0.255.255 lt 1024 deny ip any any
Example Filtering on Source Address (Host and Subnets) Using a Numbered Access List
In the following example, network 10.0.0.0 is a Class A network whose second octet specifies a subnet; that is, its subnet mask is 255.255.0.0. The third and fourth octets of a network 10.0.0.0 address specify a particular host. Using access list 2, the Cisco IOS software would accept one address on subnet 48 and reject all others on that subnet. The last line of the list shows that the software would accept addresses on all other network 10.0.0.0 subnets.
interface ethernet 0 ip access-group 2 in ! access-list 2 permit 10.48.0.3 access-list 2 deny 10.48.0.0 0.0.255.255 access-list 2 permit 10.0.0.0 0.255.255.255
Example Preventing Telnet Access to a Subnet
In the following example, the Jones subnet is not allowed to Telnet out Ethernet interface 0:
interface ethernet 0 ip access-group telnetting out ! ip access-list extended telnetting remark Do not allow Jones subnet to telnet out deny tcp 172.20.0.0 0.0.255.255 any eq telnet remark Allow Top subnet to telnet out permit tcp 172.33.0.0 0.0.255.255 any eq telnet
Example Filtering on TCP and ICMP Using Port Numbers
In the following example, the first line of the extended access list named goodports permits any incoming TCP connections with destination ports greater than 1023. The second line permits incoming TCP connections to the Simple Mail Transfer Protocol (SMTP) port of host 172.28.1.2. The last line permits incoming ICMP messages for error feedback.
interface ethernet 0 ip access-group goodports in ! ip access-list extended goodports permit tcp any 172.28.0.0 0.0.255.255 gt 1023 permit tcp any host 172.28.1.2 eq 25 permit icmp any 172.28.0.0 255.255.255.255
Example Allowing SMTP (E-mail) and Established TCP Connections
Suppose you have a network connected to the Internet, and you want any host on an Ethernet to be able to form TCP connections to any host on the Internet. However, you do not want IP hosts to be able to form TCP connections to hosts on the Ethernet except to the mail (SMTP) port of a dedicated mail host.
SMTP uses TCP port 25 on one end of the connection and a random port number on the other end. The same two port numbers are used throughout the life of the connection. Mail packets coming in from the Internet will have a destination port of 25. Outbound packets will have the port numbers reversed. The fact that the secure system behind the router always will accept mail connections on port 25 is what makes possible separate control of incoming and outgoing services. The access list can be configured on either the outbound or inbound interface.
In the following example, the Ethernet network is a Class B network with the address 172.18.0.0, and the address of the mail host is 172.18.1.2. The establishedkeyword is used only for the TCP protocol to indicate an established connection. A match occurs if the TCP datagram has the ACK or RST bits set, which indicate that the packet belongs to an existing connection.
interface ethernet 0 ip access-group 102 in ! access-list 102 permit tcp any 172.18.0.0 0.0.255.255 established access-list 102 permit tcp any host 172.18.1.2 eq 25
Example Preventing Access to the Web By Filtering on Port Name
In the following example, the Winter and Smith workstations are not allowed web access; other hosts on network 172.20.0.0 are allowed web access:
interface ethernet 0 ip access-group no_web out ! ip access-list extended no_web remark Do not allow Winter to browse the web deny host 172.20.3.85 any eq http remark Do not allow Smith to browse the web deny host 172.20.3.13 any eq http remark Allow others on our network to browse the web permit 172.20.0.0 0.0.255.255 any eq http
Example Filtering on Source Address and Logging the Packets Permitted and Denied
The following example defines access lists 1 and 2, both of which have logging enabled:
interface ethernet 0 ip address 172.16.1.1 255.0.0.0 ip access-group 1 in ip access-group 2 out ! access-list 1 permit 172.25.0.0 0.0.255.255 log access-list 1 deny 172.30.0.0 0.0.255.255 log ! access-list 2 permit 172.27.3.4 log access-list 2 deny 172.17.0.0 0.0.255.255 log
If the interface receives 10 packets from 172.25.7.7 and 14 packets from 172.17.23.21, the first log will look like the following:
list 1 permit 172.25.7.7 1 packet list 2 deny 172.17.23.21 1 packet
Five minutes later, the console will receive the following log:
list 1 permit 172.25.7.7 9 packets list 2 deny 172.17.23.21 13 packets
Example: Limiting Debug Output
The following sample configuration uses an access list to limit the debug command output. Limiting the debug output restricts the volume of data to what you are interested in, saving you time and resources.
Device(config)# ip access-list acl1 Device(config-std-nacl)# remark Displays only advertisements for LDP peer in acl1 Device(config-std-nacl)# permit host 10.0.0.44 Device# debug mpls ldp advertisements peer-acl acl1 tagcon: peer 10.0.0.44:0 (pp 0x60E105BC): advertise 172.17.0.33 tagcon: peer 10.0.0.44:0 (pp 0x60E105BC): advertise 172.16.0.31 tagcon: peer 10.0.0.44:0 (pp 0x60E105BC): advertise 172.22.0.33 tagcon: peer 10.0.0.44:0 (pp 0x60E105BC): advertise 192.168.0.1 tagcon: peer 10.0.0.44:0 (pp 0x60E105BC): advertise 192.168.0.3 tagcon: peer 10.0.0.44:0 (pp 0x60E105BC): advertise 192.168.1.33
Where to Go Next
This module describes how to create an access list that permits or denies packets based on source or destination address or protocol. However, there are other fields you could filter on, and other ways to use access lists. If you want to create an access list that filters on other fields or if you want to apply an access list to something other than an interface, you should decide what you want to restrict in your network and determine the type of access list that achieves your goal.
See the following table for references to other fields to filter and other ways to use an IP access list.
|
If you want to... |
See |
|---|---|
|
Filter based on IP Options, TCP flags, noncontiguous ports, or TTL value |
“Creating an IP Access List to Filter IP Options, TCP Flags, Noncontiguous Ports, or TTL Values” module |
|
Reorder your access list entries |
"Refining an IP Access List” module |
|
Limit access list entries to a time of day or week |
"Refining an IP Access List” module |
|
Restrict packets with noninitial fragments |
"Refining an IP Access List" module |
|
Restrict access to virtual terminal lines |
"Controlling Access to a Virtual Terminal Line” |
|
Control routing updates |
“Configuring Routing Protocol-Independent Features” module in the Cisco IOS IP Routing Protocols Configuration Guide |
|
Identify or classify traffic for features such as congestion avoidance, congestion management, and priority queuing |
“Regulating Packet Flow on a Per-Interface Basis--Using Generic Traffic Shaping” module in the Quality of Service Solutions Configuration Guide |
Additional References for Creating an IP Access List to Filter TCP Flags
Related Documents
|
Related Topic |
Document Title |
|---|---|
|
Cisco IOS commands |
|
|
Security Commands |
|
|
Order of access list entries |
"Refining an IP Access List" |
|
Access list entries based on time of day or week |
"Refining an IP Access List” |
|
Packets with noninitial fragments |
"Refining an IP Access List” |
|
Filtering on IP Options, TCP flags, noncontiguous ports, or TTL values |
“Creating an IP Access List to Filter IP Options, TCP Flags, Noncontiguous Ports, or TTL Values” |
|
Access to virtual terminal lines |
"Controlling Access to a Virtual Terminal Line” |
|
Routing updates and policy routing |
“Configuring Routing Protocol-Independent Features” modules in the Cisco IOS IP Routing Protocols Configuration Guide |
|
Traffic identification or classification for features such as congestion avoidance, congestion management, and priority queuing |
“Regulating Packet Flow on a Per-Interface Basis--Using Generic Traffic Shaping” module in the Quality of Service Solutions Configuration Guide |
Technical Assistance
|
Description |
Link |
|---|---|
|
The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password. |
Feature Information for Creating an IP Access List and Applying It to an Interface
The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.
Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.|
Feature Name |
Releases |
Feature Configuration Information |
|---|---|---|
|
Creating an IP Access List and Applying It to an Interface |
12.0(32)S4 |
IP access lists provide many benefits for securing a network and achieving nonsecurity goals, such as determining quality of service (QoS) factors or limiting debug command output. This module describes how to create standard, extended, named, and numbered IP access lists. An access list can be referenced by a name or a number. Standard access lists filter on only the source address in IP packets. Extended access lists can filter on source address, destination address, and other fields in an IP packet. |
Feedback