SIP UAC CALL INFO

Field header that indicates that the following information pertains to the SIP UAC.

Call 1

Field header.

SIP Call ID

UAC call identification number.

State of the call

Indicates the state of the call. This field is used for debugging purposes. The state is variable and may be different from one Cisco IOS release to another.

Substate of the call

Indicates the substate of the call. This field is used for debugging purposes. The state is variable and may be different from one Cisco IOS release to another.

Calling Number

Indicates the calling number.

Called Number

Indicates the called number.

Bit Flags

Indicates the bit flags used for debugging.

Source IP Address (Sig )

Indicates the signaling source IPv4 or IPv6 address.

Destn SIP Req Addr: Port:

Indicates the signaling destination Request IPv4 or IPv6 address and port number.

Destn SIP Resp Addr: Port:

Indicates the signaling destination Response IPv4 or IPv6 address and port number.

Destination Name

Indicates the signaling destination hostname, IPv4 address, or IPv6 address.

Number of Media Streams

Indicates the total number of media streams for this UAC call.

Number of Active Streams:

Indicates the total number of active media streams.

RTP Fork Object

Pointer address of the internal RTP Fork data structure.

Media Stream

Statistics about each active media stream are reported. The Media Stream header indicates the number of the media stream, and its statistics immediately follow this header.

State of the stream

State of the media stream indicated by the Media Stream header. Can be STREAM_ACTIVE, STREAM_ADDING, STREAM_CHANGING, STREAM_DEAD, STREAM_DELETING, STREAM_IDLE, or Invalid Stream State.

Stream Call ID

Identification of the stream call indicated by the Media Stream header.

Stream Type

Type of stream indicated by the Media Stream header. It can be dtmf-only, dtmf-relay, voice-only, or voice+dtmf-relay.

Negotiated Codec

Codec selected for the media stream. It can be g711ulaw, <G.729>, <G.726>, or No Codec.

Codec Payload Type

Payload type of the Negotiated Codec.

Negotiated Dtmf-relay

DTMF relay selected for the media stream indicated by the Media Stream header. It can be inband-voice or rtp-nte.

Dtmf-relay Payload Type

Payload type of the negotiated DTMF relay.

Media Source IP Addr: Port

The source IPv4 or IPv6 address and port number of the media stream indicated by the Media Stream header.

Media Dest IP Addr: Port

The destination IPv4 or IPv6 address and port number of the media stream indicated by the Media Stream header.

Local QoS Strength

The QoS strength (mandatory or optional) configured for this device.

Negotiated QoS Strength

The QoS strength (mandatory or optional) that has been negotiated.

Negotiated QoS Direction

Displays the direction in which RSVP was negotiated. For example, sendrecv indicates that RSVP was negotiated in both directions.

Local QoS Status

Displays the success or failure of RSVP reservation.

Number of UAC calls

Final SIP UAC CALL INFO field. Indicates the number of UAC calls.

SIP UAS CALL INFO

Field header that indicates that the following information pertains to the SIP UAS.

Number of UAS calls

Final SIP UAS CALL INFO field. Indicates the number of UAS calls.

Local UUID

Unique identifier generated from the originating user agent.

Remote UUID

Unique identifier generated from the terminating user agent.

Local Crypto Suite

Crypto suite negotiated by CUBE. All the crypto suites configured in CUBE are listed in parenthesis.

Remote Crypto Suite

Crypto suites received.

Total active connections

Indicates all the connections that the gateway holds for various targets. Statistics are broken down within individual fields.

No. of send failures.

Indicates the number of TCP or UDP messages dropped by the transport layer. Messages are dropped if there were network issues, and the connection was frequently ended.

No. of remote closures

Indicates the number of times a remote gateway ended the connection. A higher value indicates a problem with the network or that the remote gateway does not support reusing the connections (thus it is not RFC 3261-compliant). The remote closure number can also contribute to the number of send failures.

No. of conn. failures

Indicates the number of times that the transport layer was unsuccessful in establishing the connection to the remote agent. The field can also indicate that the address or port that is configured under the dial peer might be incorrect or that the remote gateway does not support that mode of transport.

No. of inactive conn. ageouts

Indicates the number of times that the connections were ended or timed out because of signaling inactivity. During call traffic, this number should be zero. If it is not zero, we recommend that the inactivity timer be tuned to optimize performance by using the timers command.

Max. tcp send msg queue size of 0, recorded for 0.0.0.0:0

Indicates the number of messages waiting in the queue to be sent out on the TCP connection when the congestion was at its peak. A higher queue number indicates that more messages are waiting to be sent on the network. The growth of this queue size cannot be controlled directly by the administrator.

Tuples with no matching socket entry

Any tuples for the connection entry that are marked with "**" at the end of the line indicate an upper transport layer error condition; specifically, that the upper transport layer is out of sync with the lower connection layer. Cisco IOS Software should automatically overcome this condition. If the error persists, execute the clear sip-ua udp connection or clear sip-ua tcp connection command and report the problem to your support team.

Tuples with mismatched address/port entry

Any tuples for the connection entry that are marked with "++" at the end of the line indicate an upper transport layer error condition, where the socket is probably readable, but is not being used. If the error persists, execute the clear sip-ua udp connection or clear sip-ua tcp connection command and report the problem to your support team.

Remote-Agent Connections-Count

Connections to the same target address. This field indicates how many connections are established to the same host.

Remote-Port Conn-Id Conn-State WriteQ-Size

Connections to the same target address. This field indicates how many connections are established to the same host. The WriteQ-Size field is relevant only to TCP connections and is a good indicator of network congestion and if there is a need to tune the TCP parameters.

Cipher

Displays the negotiated Cipher.

Curve

Curve Size of the ECDSA Cipher.

PSTN-Cause

Reasons for PSTN call failure or completion. PSTN cause code range is from 1 to 127.

Configured SIP-Status

Configured SIP status code or event. SIP Status code range is from 400 to 699.

Default SIP-Status

Default mapping between and PSTN and SIP networks.

SIP-Status

Configured SIP status code or event. SIP status code range is from 400 to 699.

Configured PSTN-Cause

Reasons for PSTN call failure or completion. PSTN cause code range is from 1 to 127.

Default PSTN-Cause

Default mapping between and SIP and PSTN networks.

SIP UA MIN-SE Value (seconds)

Field header indicating that the following information shows the current value of the Min-SE header, in seconds.

Min-SE

Current value of the Min-SE header, in seconds.

MWI type

Indicates the type of MWI service. 1 indicates MWI application service, which is used when a router provides MWI relay service. 2 indicates SIP-based MWI.

MWI server

Indicates the host device housing the domain name server (DNS) that resolves the name of the voice-mail server.

MWI expires

Indicates the expiration time, in seconds.

MWI port

Indicates the port used by SIP signaling.

MWI transport type

Indicates the desired transport protocol. Values are tcp or udp. UDP is the default.

MWI unsolicited

Indicates whether unsolicited MWI is configured.

MWI server IP address

Indicates the IP address of the voice-mail MWI server in hex format. If you configured the mwi-server command for DNS format, DNS lookup may result in multiple IP addresses. All IP addresses are listed.

MWI ipaddr cnt

Indicates the number of IP addresses associated with the voice-mail MWI server.

MWI ipaddr idx

Indicates which MWI server IP address is currently being used. The index starts from 0.

MWI server

Indicates the IP address of the MWI server; the port; and transport protocol (1 indicates UDP; 2 indicates TCP).

MWI server dns lookup retry cnt

Indicates the number of retries for DNS lookup.

endpoint / mwi status

Indicates the endpoint or voice port and whether MWI notification is active. That is, if a message is waiting, the status is on. Once the message is deleted, the status is off.

Line

The phone number to register.

peer

The registration destination number.

expires (sec)

The amount of time, in seconds, until registration expires.

registered

Registration status.

bye retry count

Number of times that a Bye request is retransmitted.

cancel retry count

Number of times that a Cancel request is retransmitted.

comet retry count

Number of times that a COMET request is retransmitted.

invite retry count

Number of times that an Invite request is retransmitted.

notify retry count

Number of times that a Notify message is retransmitted.

prack retry count

Number of times that a PRACK request is retransmitted.

refer retry count

Number of times that a Refer request is retransmitted.

reliable 1xx count

Number of times that a Reliable 1xx request is retransmitted.

response retry count

Number of times that a Response request is retransmitted.

SIP UA Retry Values

Field header for SIP UA retry values.

Ack 0/0

A confirmed final response received or sent.

Accepted 0/0

202 A successful response to a Refer request received or sent.

AddrIncomplete 0/0

484 Address supplied is incomplete.

AlternateService 0

380 Unsuccessful call; however, an alternate service is available.

Ambiguous 0/0

485 Address supplied is ambiguous.

BadEvent 0/0

489 Bad Event response indicates a Subscribe request having an event type that the server could not understand.

BadExtension 0/0

420 Server could not understand the protocol extension in the Require header.

BadGateway 0/0

502 Network is out of order.

BadRequest

400 Bad Request (includes the malformed Via header).

BadSipVer 0/0

505 Requested SIP version is not supported.

BusyEverywhere 0/0

600 Called party is busy.

BusyHere 0/0

486 Called party is busy.

Bye 0

Number of times that a Bye request is retransmitted to the other user agent.

Bye 0/0

Terminated the session.

CallLegNonExistent 0/0

481 Server is ignoring the request. Either is was a Bye request and there was no matching leg ID, or it was a Cancel request and there was no matching transaction.

Cancel 0

Number of times that a Cancel request is retransmitted to the other user agent.

Cancel 0/0

Terminated the pending request.

Comet 0

Number of times that a COMET request is retransmitted to the other user agent.

Comet 0/0

Conditions have been met.

Conflict 0/0

409 Temporary failure.

Decline 0/0

603 Call rejected.

Forbidden 0/0

403 The SIP server has the request, but cannot provide service.

Forwarded 0/0

181 Call has been forwarded.

GatewayTimeout 0/0

504 The server or gateway did not receive a timely response from another server (such as a location server).

Gone 0/0

410 Resource is no longer available at the server, and no forwarding address is known.

Info 0/0

Number of information messages the gateway has received (inbound) and how many have been transmitted (outbound).

InternalError 0/0

500 The server or gateway encountered an unexpected error that prevented it from processing the request.

Invite 0

Number of times that an INVITE request is retransmitted to the other user agent.

Invite 0/0

Initiates a call.

LoopDetected 0/0

482 A loop--server received a request that included itself in the path.

MethodNotAllowed 0/0

405 Method specified in the request is not allowed.

MovedPermanently 0

301 User is no longer available at this location.

MovedTemporarily 0

302 User is temporarily unavailable.

MultipleChoice 0

300 Address resolves to more than one location.

NotAcceptable 0/0

406/606 Call was contacted, but some aspect of the session description was unacceptable.

NotAcceptableMedia 0/0

406 Call was contacted, but some aspect of the session description was unacceptable.

NotExistAnywhere 0/0

604 Server has authoritative information that the called party does not exist in the network.

NotFound 0/0

404 Called party does not exist in the specified domain.

NOTIFY 0

Number of times that a Notify is retransmitted to the other user agent.

NOTIFY 0/0

Number of Notify messages received or sent.

NotImplemented 0/0

501 Service or option not implemented in the server or gateway.

OkBye 0/0

200 Successful response to a Bye request.

OkCancel 0/0

200 Successful response to a Cancel request.

OkInfo

200 Successful response to an INFO request.

OkInvite 0/0

200 Successful response to an INVITE request.

OkNOTIFY 0/0

200 Successful response to a Notify request.

OkOptions 0/0

200 Successful response to an Options request.

OkPrack 0/0

200 Successful response to a PRACK request.

OkPreconditionMet 0/0

200 Successful response to a PreconditionMet request.

OkRegister 0/0

200 Successful response to a Register request.

OkSubscribe 0/0

200 Successful response to a SUBSCRIBE request.

Options 0/0

Query the receiving or sending server as to its capabilities.

PaymentRequired 0/0

402 Payment is required to complete the call.

Prack 0

Number of times that a PRACK request is retransmitted to the other user agent.

Prack 0/0

Provisional response received or sent.

PreCondFailure 0/0

580 The session could not be established because of failure to meet required preconditions.

ProxyAuthReqd 0/0

407 Rejected for proxy authentication.

Queued 0/0

182 Until the called party is available, the message is queued.

RedirectResponseMappedToClientError 0

Indicates the count of incoming 3xx responses that were mapped to 4xx responses. It is incremented when the no redirection command is active. For the default case, the 3xx messages are processed per RFC 2543, and this counter is not incremented.

This counter counts only inbound messages and only the 3xx responses that are known (300, 301, 302, 305, and 380).

The counter is cleared when the clear sip -ua statistics command is issued.

Refer 0

Number of times the Refer request is retransmitted to the other user agent.

Refer 0/0

Number of Refer requests received or sent.

Register 0/0

Number of Register requests received or sent.

Register 0

Number of times that a Register request is retransmitted to the other user agent.

Reliable1xx 0

Indicates the number of times the Reliable 1xx response is retransmitted to the other user agent.

ReqEntityTooLarge 0/0

413 Server refuses to process request because the request is larger than is acceptable.

ReqTimeout 0/0

408 Server could not produce a response before the Expires time- out.

RequestCancel 0/0

Request has been canceled.

ReqURITooLarge 0/0

414 Server refuses to process, because the URI (URL) request is larger than is acceptable.

Response 0

Indicates number of Response retries.

Retry Statistics

One of the three categories of response statistics.

Ringing 0/0

180 Called party has been located and is being notified of the call.

SeeOther 0

303 Transfer to another address.

ServiceUnavail 0/0

503 Service option is not available because of an overload or maintenance problem.

SessionProgress 0/0

183 Indicates in-band alerting.

SIP Response Statistics (Inbound/Outbound)

One of the three categories of response statistics.

SIP Total Traffic Statistics (Inbound/Outbound)

One of the three categories of response statistics.

Subscribe 0

Indicates the number of Retry Subscribe messages sent.

Subscribe 0/0

Number of Subscribe requests received or sent.

TempNotAvailable 0/0

480 Called party did not respond.

TooManyHops 0/0

483 A server received a request that required more hops than is allowed by the Max-Forward header.

Trying 0/0

100 Action is being taken with no resolution.

Unauthorized 0/0

401 The request requires user authentication.

UnsupportedMediaType 0/0

415 Server refuses to process a request because the service option is not available on the destination endpoint.

UseProxy 0

305 Caller must use a proxy to contact called party.

SIP User Agent Status

UA status.

SIP User Agent for UDP

User Datagram Protocol (UDP) is enabled or disabled.

SIP User Agent for TCP

TCP is enabled or disabled.

SIP User Agent bind status (signaling)

Binding for signaling is enabled or disabled.

SIP User Agent bind status (media)

Binding for media is enabled or disabled.

SIP early-media for 180 responses with SDP

Early media cut-through treatment for 180 responses with SDP can be enabled (the default treatment) or disabled, with local ringback provided.

SIP max-forwards

Value of max-forwards of SIP messages.

SIP DNS SRV version

Style of the DNS SRV query: 1 for RFC 2052 or 2 for RFC 2782.

NAT Settings for the SIP-UA

Symmetric Network Address Translation (NAT) settings when the feature is enabled.

Role in SDP

Identifies the endpoint function in the connection setup procedure during symmetric NAT traversal. The endpoint role may be set to active, meaning that it initiates a connection, or to passive, meaning that it accepts a connection. A value of none in this field means that the feature is disabled.

Check media source packets

Media source packet checking is enabled or disabled.

Maximum duration for a telephone-event in NOTIFYs

Shows the time interval, in milliseconds (ms), between consecutive NOTIFY messages for a telephone event.

SIP support for ISDN SUSPEND/RESUME

Suspend and Resume support is enabled or disabled.

Redirection (3xx) message handling

Redirection can be enabled, which is the default status, according to RFC 2543. Or handling of redirection 3xx messages can be disabled, allowing the gateway to treat 3xx redirect messages as 4xx error messages.

Reason Header will override Response/Request Codes

Reason header is enabled or disabled.

protocol mode is ipv6

States whether the protocol being used is IPv6 or IPv4.

Version line (v=)

Indicates if the SDP version is required.

Owner line (o=)

Indicates if the session originator is required.

Timespec line (t=)

Indicates if the session start and stop times are required.

Media supported

Media information.

Network types supported

Always IN for Internet.

Address types supported

Identifies the Internet Protocol version.

Transport types supported

Identifies the transport protocols supported.

Maximum allow incoming out-of-dialog refer

Maximum number of incoming OOD-R sessions that the router is allowed. Value set by the refer-ood enable command. Default is 500.

Current existing incoming out-of-dialog refer dialogs

Number of currently active incoming OOD-R sessions.

outgoing out-of-dialog refer dialogs

Number of currently active outgoing OOD-R sessions used for line status updates.

SIP UA Timer Values (millisecs)

SIP UA timer status.

trying

Time to wait before a Trying message is retransmitted.

expires

Time to wait before an Expires message is retransmitted.

connect

Time to wait before a Connect message is retransmitted.

disconnect

Time to wait before a Disconnect message is retransmitted.

prack

Time to wait before a PRACK acknowledgment is retransmitted.

rel1xx

Time to wait before a Rel1xx response is retransmitted.

notify

Time to wait before a Notify response is retransmitted.

refer

Time to wait before a Retry request is retransmitted.

register

Time to wait before a Register request is retransmitted.

hold

Time to wait in minutes before a BYE request is sent.

buffer-invite

Time to buffer the INVITE while waiting for display information.

tcp/udp aging

Time to wait in minutes before a TCP or UDP connection is aged out.

tls aging

Time to wait in minutes before a TLS connection is aged out.

tls establish

Time to wait in seconds for establishing a TLS connection with the remote server.

SPE

Slot and port number of the SPE.

Last Clearing of Statistics Counters

Last time the statistics counters were cleared by means of the clear spe counters command.

Buffer Overflow Errors

The digital-signal-processor (DSP) buffer has overflowed. If overflow continues, data will be lost and voice will be distorted (as concealment is added).

Endpoint Detection Errors

A voice frame has arrived after a predefined timer expires, causing the DSP to declare it late. If the frame consists of the SID/marker bit, it causes an endpoint detection error and the late packet is included as an endpoint detection error.

Packets Received Early

The number of frames held in the delay buffer exceeds the expected playout delay -- that is, the delay buffer is overrun (too many frames waiting to be played out for the expected playout delay). At this point, the buffer must reduce the excess delay using intelligent frame deletion to preserve audio continuity.

Packets Received Late

The DSP has received an out-of-sequence packet and started a timer for the missing packet. The packet has failed to arrive in time; it is marked as late and the statistic is incremented. The DSP does interpolative or silence concealment for any missing frames. This type of problem is apt to occur in a congested network and results in lost packets and diminished voice quality.

Bad Protocol Headers

Packets have been rejected for any of the following reasons: bad protocol header, incorrect length, unknown packet format, unknown Real-Time Transport Protocol synchronization source (SSRC), incorrect checksum (when the Extended header is used), cumulative number of packets with invalid RTP headers (the header extension exceeds the packet length), or an invalid User Datagram Protocol (UDP)/IP header if extended encapsulation is enabled.

SS7 MTP1 Session-channel

Information about channel IDs.

all

Information on all assigned channel IDs if a particular ID is not specified.

channel

Channel ID assigned by use of the channel-id command.

assigned

Name of the interface serial object to which the channel ID is assigned.

interface

Whether the link type is digital or serial.

serial interface

Name of the interface serial object and its type (serial or digital).

SCC port

SCC port on the DFC card that was internally assigned by software to service that link (useful to resolve conflicts when trying to create a serial link).

link state

MTP1 link state is started (generally reflects the shutdown and no shutdown entry options.

IDB state

Actual state of the internal Interface Descriptor Block (IDB), which is useful for developers.

rcv-pool

Heading for receive buffer-pool information.

pool-name

Internal name for the pool.

congested

Whether the receive buffers are congested or not.

in-use buffers

How many of the receive buffers are currently in use.

free buffers

How many of the receive buffers are free (not in use).

tx-pool

Heading for transmit buffer-pool information.

pool-name

Internal name for the pool.

in-use buffers

How many of the transmit buffers are currently in use.

free buffers

How many of the transmit buffers are free (not in use).

interface

Name of the serial interface for the link.

type

Type of link: serial or digital.

SCC

Assigned MGC port. The SCC chip number is used by Cisco developers to check output from the debug ss7 mtp1 command.

State

Whether the link is stopped or started.

channel

Assigned channel ID.

session channel

Assigned channel ID.

session set

Assigned SS7 session number.

PCR Enabled

Whether the error-correction method is set to PCR.

TRUE indicates that PCR is enabled.

FALSE indicates that PCR is disabled.

Forced Retransmission

Whether forced retransmission is enabled or disabled.

TRUE indicates that forced-retransmission is enabled.

FALSE indicates that forced-retransmission is disabled.

N2 Threshold

N2 Octet-count

Status of the N2 parameter and maximum octets available.

Number of octets stored in the RTB for an SS7 signaling channel.

--

MTP2LSC

Overall status of the link.

OOS--Link is out of service.

INITIAL_ALIGNMENT--Link is in a transitional link alignment state.

ALIGNED_READY--Link is in a transitional link alignment state.

ALIGNED_NOT_READY--Link is in a transitional link alignment state.

INSERVICE--Link is in service.

PROCESSOR_OUTAGE--There is an outage in the local processor. This state implies that the link has been aligned.

POWER_OFF--It is possible you don’t have the I/O memory set to at least 40 percent. There may not be enough memory for the SS7 MTP2 signaling.

MTP2IAC

Status of the initial alignment control state machine.

IDLE--State machine is idle. It is not aligning the link.

NOT_ALIGNED--State machine has begun the alignment process.

ALIGNED-- Link has exchanged the alignment handshake with the remote device.

PROVING--Link alignment is being proven. This is a waiting period before the LSC state changes to INSERVICE.

MTP2TXC

Status of the transmission control state machine.

IDLE--State machine is inactive.

INSERVICE--State machine is the active transmitter.

MTP2RC

Status of the receive control state machine.

IDLE--State machine is inactive.

INSERVICE--State machine is the active receiver.

MTP2SUERM

Status of the signal unit error monitor (SUERM).

IDLE--State machine is inactive.

MONITORING--SUERM is active. SUERM uses a leaky-bucket algorithm to track link errors while the link is in service. If the number of link errors reaches the threshold, the link is taken out of service.

MTP2AERM

Status of the alignment error rate monitor state machine (AERM).

IDLE--State machine is inactive.

MONITORING--Alignment error monitor is active. This is part of the alignment process.

MTP2CONGESTION

Status of the congestion control state machine.

IDLE--State machine is inactive. No congestion is detected; normal traffic flow.

ACTIVE--Congestion has been declared. The Cisco 2600 series router is sending SIBs every T5, which indicates that the remote end should stop sending new MSUs until the local Cisco 2600 series router can catch up.

Congestion Backhaul

Congestion status of the backhaul link between the Cisco SLT and the media gateway controller.

Abate--Link between the Cisco 2600 series router and the media gateway controller is not under congestion.

Onset--Link between the Cisco 2600 series router and the media gateway controller is under congestion. and the Media Gateway Controller should stop sending new MSUs until the local Cisco 2600 series router can catch up.

Remote Processor Outage

Processor outage status of the remote.

TRUE indicates that the remote is in processor outage.

FALSE indicates that the remote has not declared processor outage.

Forced Retransmission

Whether forced retransmission is enabled or disabled.

TRUE--Indicates that forced retransmission is enabled.

FALSE--Indicates that forced retransmission is disabled.

PCR Enabled

Whether the error-correction method is set to PCR.

TRUE--Indicates that PCR is enabled.

FALSE--Indicates that PCR is disabled.

N2

Status of the N2 parameter.

Octet counts are specified.

OMIACAlignAttemptCount

OMIACAlignFailCount

OMIACAlignCompleteCount

Counts for Initial Alignment Control (IAC) attempts.

OMMSU_TO_XMIT_Count

Related to the results of the show ss7 sm stats command’s PDU_pkts_recieve_count statistic. The number shown in OMMSU_TO_XMIT_Count is less than the PDU_pkts_recieve_count because OMMSU_TO_XMIT_Count shows the number of PDUs going out on the link, while the PDU_pkts_recieve_count includes PDUs that are internal to MTP2.

OMMSU_RCV_Count

Related to the results of the show ss7 sm stats command’s packets_send_count.

OMLSSU_XMIT_Count

OMLSSU_XMIT_SINCount

OMLSSU_XMIT_SIECount

OMLSSU_XMIT_SIOCount

OMLSSU_XMIT_SIOSCount

OMLSSU_XMIT_SIPOCount

OMLSSU_XMIT_SIBCount

Number of times that MTP 2 has posted the specific Link Status Signal Unit (LSSU) to MTP 1. They do not show the number of LSSUs actually sent over the link.

OMLSSU_RCV_Count

OMLSSU_RCV_SINCount

OMLSSU_RCV_SIECount

OMLSSU_RCV_SIOCount

OMLSSU_RCV_SIOSCount

OMLSSU_RCV_SIPOCount

OMLSSU_RCV_SIBCount

OMLSSU_RCV_InvalidCount

Number of LSSUs received by MTP 2 from MTP 1. Because of MTP 1 filtering, this is not the same as the actual LSSUs sent over the link.

OMT1_TMO_Count

OMT2_TMO_Count

OMT3_TMO_Count

OMT4_TMO_Count

OMT5_TMO_Count

OMT6_TMO_Count

OMT7_TMO_Count

OMT8_TMO_Count

OMTA_TMO_Count

OMTF_TMO_Count

OMTO_TMO_Count

OMTA_TMO_Count

OMLostTimerCount

Information about timers in use.

OMLostBackhaulMsgs

How many messages received from the Media Gateway Controller have been lost because of a lack of resources in the Cisco 2600 series router. This count is related to the results of the show ss7 sm stats command’s PDU_pkts_recieve_count statistic. For example, if the Media Gateway Controller sends 100 MSUs and the Cisco 2600 series router only has 65 free buffers, 35 MSUs might be lost.

Remote Host, Local Host

IP address and port number for the session.

retrans_t

Retransmission timer value.

cumack_t

Cumulative acknowledgment timer value.

m_cumack

Maximum number of segments that can be received before the RUDP sends an acknowledgment.

m_outseq

Maximum number of out-of-sequence segments that can be received before the RUDP sends an extended acknowledgment.

m_rcvnum

Maximum number of segments that the remote end can send before receiving an acknowledgment.

Session-set:0

One of four SS7 session sets is configured.

State

The session is ACTIVE.

Failover-timer

2 Sessions:

3 SS7 Links:

Session-set:1

One of four SS7 session sets is configured.

State

The session is IDLE.

Failover-timer

The number is set to 5 seconds.

0 Sessions:

No sessions are configured.

0 SS7 Links:

No SS7 links are configured.

Session-set:2

One of four SS7 session sets is configured.

State

The session is ACTIVE.

Failover-timer

2 Sessions:

1 SS7 Links :

SS7 link at serial interface 7/0:1 has channel ID 2 and current MTP2 link state of INSERVICE.

Session-set:3

One of four SS7 session sets is configured.

State

The session is IDLE.

Failover-timer

The number is set to 5 seconds.

0 Sessions:

No sessions are configured.

0 SS7 Links:

No SS7 links are configured.

Active Call Info

Displays only when an active call is in progress.

Call Reference

Reference number created by Cisco Unified Communications Manager to track messages associated with a specific call.

Call State

Call processing state:

• ACTIVE--Established call connection

• IDLE--No call connection

• UNREGISTERED--Device is not registered with the Cisco Unified Communications Manager

Called Number

Device called number.

Calling Number

Device calling number.

ccw_on

Displays status of Cancel Call Waiting feature:

• False--Inactive on port.

• True--Active on port.

Codec

Displays codec type.

CWT Repetition Interval

Displays the call waiting tone configuration.

Dev Cntl

Call-control device that is managing the analog endpoints. CCM represents Cisco Unified Communications Manager. CME represents Cisco Unified Communications Manager Express.

Device Id

Identifier used between the Cisco Unified Communications Manager and gateway to uniquely identify an endpoint.

Device Name

Unique device ID of the analog endpoint. The device ID is derived from an algorithm using the MAC address of the SCCP interface on the voice gateway and the hexadecimal translation of the port's slot number and port number.

Device State

Displays whether device is available for use:

• ACTIVE_PENDING--Call is pending certain events before going active.

• INFO_RCVD--Call information is received from the Cisco Unified Communications Manager during call setup.

• INIT--Waiting to reinitialize.

• IS--In service.

• OFFHOOK--Device is off-hook.

• OFFHOOK_TIMEOUT--Digit timeout occurred while the device is off-hook.

• ONHOOK_PENDING--Call is pending certain events before going to the on-hook state.

• OOS--Out of service.

• PROCEED--Dialed number translation is complete and call setup is in progress.

• REM_ONHOOK_PENDING--Call is pending certain events before going to the on-hook state.

• RINGING--An incoming call has invoked ringing of the receiving device.

Device Type

Shows phone type:

• ALG--Analog.

• BRI--ISDN BRI.

Diagnostic

Reason code for a device error condition.

Dial Peer(s)

Dial peer name.

Dialtone after remote onhook feature

Displays feature status:

• Activated

• Not activated

Directory Number

Assigned to the device by the Cisco Unified Communications Manager.

Last Event

Last event processed by this port.

Local IP Addr

IPv4 address of this gateway used to stream audio using the Real-Time Transport Protocol (RTP).

Local IPv6 Addr

IPv6 address of this gateway used to stream audio using the RTP.

Local IP Port

IP port of this gateway used to stream audio using RTP.

Port Identifier

Identifies the physical voice port.

Remote IP Addr

IPv4 address of the far-end gateway that streams audio using RTP.

Remote IPv6 Addr

IPv6 address of the far-end gateway that streams audio using RTP.

Remote IP Port

IP port of the far-end gateway that streams audio using RTP.

vmwi

Displays LED status:

• On

• Off

call forward all

FAC prefix plus FAC set by the call forward all command.

call forward cancel

FAC prefix plus FAC set by the call forward cancel command.

cancel call waiting

FAC prefix plus FAC set by the cancel-call-waiting command.

key

Code set for call back on Busy by the activation-key command.

meetme-conference

FAC prefix plus FAC set by the meetme-conference command.

pickup different group

FAC prefix plus FAC set by the pickup group command.

pickup direct

FAC prefix plus FAC set by the pickup direct command.

pickup local group

FAC prefix plus FAC set by the pickup local command.

prefix

FAC prefix set by the prefix (stcapp-fsd) command or by the prefix (stcapp-fac) command.

redial

FSD prefix plus FSD code set by the redial command.

speeddial number of digit(s)

FSD digit length set by the digit command.

speeddialx

FSD prefix plus FSD code from the range set by the speed dial command.

timeout

Period in seconds for ringing timer set for Call back on Busy by using the ringing-timeout command.

voicemail

FSD prefix plus FSD code set by the voicemail command.

DevErr

Device errors.

CallOA

Call origination attempts.

CallTA

Call termination attempts.

CallErr

Call errors.

CallPE

Call preemptions.

Last response code

ASNL response codes:

ASNL_NONE--Subscription request was initiated. No response has been received from the subscription server.

ASNL_SUBSCRIBE_SUCCESS--Subscription request was successful.

ASNL_SUBSCRIBE_PENDING--Subscription request has been sent out. Waiting for a response.

ASNL_SUBSCRIBE_FAILED--Subscription request failed.

ASNL_SUBSCRIBE_SOCKET_ERR--Socket error occurred when the subscription was initiated.

ASNL_SUBSCRIBE_REQ_TIMED_OUT_ERR--Subscription request was sent out. No response has been received from the subscription server.

ASNL_SUBSCRIBE_CONN_TIMED_OUT_ERR--The client requested a connection to send a SUBSCRIBE request. Connection establishment timed out. Valid for Transmission Control Protocol (TCP) only.

ASNL_SUBSCRIBE_DNS_ERR--Domain Name Server (DNS) error occurred when resolving the host name specified in the subscription request.

ASNL_SUBSCRIBE_CONN_CREATE_FAILED_ERR--Attempt to create a connection to the subscription server failed. Valid for TCP only.

Last response code (continued)

ASNL_SUBSCRIBE_INTERNAL_CLIENT_ERR--Internal software error occurred while initiating subscription request.

ASNL_SUBSCRIBE_RESPONSE_ERR--Invalid response was received from the subscription server for the subscription request from client.

ASNL_SUBSCRIBE_EXPIRED--Subscription expired.

ASNL_SUBSCRIBE_CLEANUP--Subscription termination initiated from command line interface (CLI).

ASNL_UNSUBSCRIBE_SUCCESS--Subscription termination request was successful.

ASNL_UNSUBSCRIBE_PENDING--Subscription termination request was sent out. Waiting for a response.

ASNL_UNSUBSCRIBE_FAILED --Subscription termination request failed.

ASNL_UNSUBSCRIBE_SOCKET_ERR--Socket error occurred when the subscription termination request was initiated.

ASNL_UNSUBSCRIBE_REQ_TIMED_OUT_ERR--Subscription termination request was sent out. No response received from the subscription server.

ASNL_UNSUBSCRIBE_CONN_TIMED_OUT_ERR--The client requested a connection to send an UNSUBSCRIBE request. Connection establishment timed out. Valid for TCP only.

ASNL_UNSUBSCRIBE_CONN_CREATE_FAILED_ERR--Attempt to create a connection to the subscription server failed. Valid for TCP only.

ASNL_UNSUBSCRIBE_INTERNAL_ERR--Internal software error occurred when initiating subscription termination request.

ASNL_UNSUBSCRIBE_RESPONSE_ERR--Invalid response was received from the subscription server for the subscription termination request from the client.

ASNL_NOTIFY_RCVD--Received a notification request from the subscription server.

Last error code

Subscription error codes:

ASNL_SUBSCRIBE_PENDING--Subscription request has been sent out. Waiting for a response.

ASNL_SUBSCRIBE_FAILED--Subscription request failed.

ASNL_SUBSCRIBE_SOCKET_ERR--Socket error occurred when the subscription was initiated.

ASNL_SUBSCRIBE_REQ_TIMED_OUT_ERR--Subscription request was sent out. No response has been received from the subscription server.

ASNL_SUBSCRIBE_CONN_TIMED_OUT_ERR--The client requested a connection to send a SUBSCRIBE request. Connection establishment timed out. Valid for TCP only.

ASNL_SUBSCRIBE_DNS_ERR--DNS error occurred when resolving the host name specified in the subscription request.

ASNL_SUBSCRIBE_CONN_CREATE_FAILED_ERR--Attempt to create a connection to the subscription server failed. Valid for TCP only.

ASNL_SUBSCRIBE_INTERNAL_CLIENT_ERR--Internal software error occurred while initiating subscription request.

ASNL_SUBSCRIBE_RESPONSE_ERR--Invalid response was received from the subscription server for the subscription request from client.

ASNL_SUBSCRIBE_EXPIRED--Subscription expired.

ASNL_UNSUBSCRIBE_FAILED --Subscription termination request failed.

ASNL_UNSUBSCRIBE_SOCKET_ERR--Socket error occurred when the subscription termination request was initiated.

ASNL_UNSUBSCRIBE_REQ_TIMED_OUT_ERR--Subscription termination request was sent out. No response received from the subscription server.

ASNL_UNSUBSCRIBE_CONN_TIMED_OUT_ERR--The client requested a connection to send an UNSUBSCRIBE request. Connection establishment timed out. Valid for TCP only.

ASNL_UNSUBSCRIBE_CONN_CREATE_FAILED_ERR--Attempt to create a connection to the subscription server failed. Valid for TCP only.

ASNL_UNSUBSCRIBE_INTERNAL_ERR--Internal software error occurred when initiating subscription termination request.

ASNL_UNSUBSCRIBE_RESPONSE_ERR--Invalid response was received from the subscription server for the subscription termination request from the client.

Last response code

ASNL response codes. The field can be one of the following values:

ASNL_NONE--Subscription request was initiated. No response has been received from the subscription server.

ASNL_SUBSCRIBE_SUCCESS--Subscription request was successful.

ASNL_SUBSCRIBE_PENDING--Subscription request has been sent out. Waiting for a response.

ASNL_SUBSCRIBE_FAILED--Subscription request failed.

ASNL_SUBSCRIBE_SOCKET_ERR--Socket error occurred when the subscription was initiated.

ASNL_SUBSCRIBE_REQ_TIMED_OUT_ERR--Subscription request was sent out. No response has been received from the subscription server.

ASNL_SUBSCRIBE_CONN_TIMED_OUT_ERR--The client requested a connection to send a SUBSCRIBE request. Connection establishment timed out. Valid for Transmission Control Protocol (TCP) only.

ASNL_SUBSCRIBE_DNS_ERR--Domain Name Server (DNS) error occurred when resolving the host name specified in the subscription request.

ASNL_SUBSCRIBE_CONN_CREATE_FAILED_ERR--Attempt to create a connection to the subscription server failed. Valid for TCP only.

ASNL_SUBSCRIBE_INTERNAL_ERR--Internal software error occurred while initiating subscription request.

ASNL_SUBSCRIBE_RESPONSE_ERR--Invalid response was received from the subscription server for the subscription request from client.

ASNL_SUBSCRIBE_EXPIRED--Subscription expired.

ASNL_SUBSCRIBE_CLEANUP--Subscription termination initiated from command line interface (CLI).

ASNL_UNSUBSCRIBE_SUCCESS--Subscription termination request was successful.

ASNL_UNSUBSCRIBE_PENDING--Subscription termination request was sent out. Waiting for a response.

ASNL_UNSUBSCRIBE_FAILED --Subscription termination request failed.

Last response code (continued)

ASNL_UNSUBSCRIBE_SOCKET_ERR--Socket error occurred when the subscription termination request was initiated.

ASNL_UNSUBSCRIBE_REQ_TIMED_OUT_ERR--Subscription termination request was sent out. No response received from the subscription server.

ASNL_UNSUBSCRIBE_CONN_TIMED_OUT_ERR--The client requested a connection to send an UNSUBSCRIBE request. Connection establishment timed out. Valid for TCP only.

ASNL_UNSUBSCRIBE_CONN_CREATE_FAILED_ERR--Attempt to create a connection to the subscription server failed. Valid for TCP only.

ASNL_UNSUBSCRIBE_INTERNAL_ERR--Internal software error occurred when initiating subscription termination request.

ASNL_UNSUBSCRIBE_RESPONSE_ERR--Invalid response was received from the subscription server for the subscription termination request from the client.

ASNL_NOTIFY_RCVD--Received a notification request from the subscription server.

Last error code

Subscription error codes. The field can be one of the following values:

ASNL_SUBSCRIBE_PENDING--Subscription request has been sent out. Waiting for a response.

ASNL_SUBSCRIBE_FAILED--Subscription request failed.

ASNL_SUBSCRIBE_SOCKET_ERR--Socket error occurred when the subscription was initiated.

ASNL_SUBSCRIBE_REQ_TIMED_OUT_ERR--Subscription request was sent out. No response has been received from the subscription server.

ASNL_SUBSCRIBE_CONN_TIMED_OUT_ERR--The client requested a connection to send a SUBSCRIBE request. Connection establishment timed out. Valid for TCP only.

ASNL_SUBSCRIBE_DNS_ERR--DNS error occurred when resolving the host name specified in the subscription request.

ASNL_SUBSCRIBE_CONN_CREATE_FAILED_ERR--Attempt to create a connection to the subscription server failed. Valid for TCP only.

ASNL_SUBSCRIBE_INTERNAL_ERR--Internal software error occurred while initiating subscription request.

Last error code (continued)

ASNL_SUBSCRIBE_RESPONSE_ERR--Invalid response was received from the subscription server for the subscription request from client.

ASNL_SUBSCRIBE_EXPIRED--Subscription expired.

ASNL_UNSUBSCRIBE_FAILED --Subscription termination request failed.

ASNL_UNSUBSCRIBE_SOCKET_ERR--Socket error occurred when the subscription termination request was initiated.

ASNL_UNSUBSCRIBE_REQ_TIMED_OUT_ERR--Subscription termination request was sent out. No response received from the subscription server.

ASNL_UNSUBSCRIBE_CONN_TIMED_OUT_ERR--The client requested a connection to send an UNSUBSCRIBE request. Connection establishment timed out. Valid for TCP only.

ASNL_UNSUBSCRIBE_CONN_CREATE_FAILED_ERR--Attempt to create a connection to the subscription server failed. Valid for TCP only.

ASNL_UNSUBSCRIBE_INTERNAL_ERR--Internal software error occurred when initiating subscription termination request.

ASNL_UNSUBSCRIBE_RESPONSE_ERR--Invalid response was received from the subscription server for the subscription termination request from the client.

notificationMList

String name of the method list of this subscription.

notificationPeriod

notificationType

Type of accounting record for which notification is sent: start, stop, update, or accounting-on.

reportAcctFailure

Indicates whether to send accounting failure responses to the individual application call script before the method list is declared unreachable.

subscription state

When a subscription is completed successfully, the state is notify_acked.

TIMERS

Settings for specified timers.

STATE

State of the connection.

QUEUES

The number of writeQ, sec_writeQ, and readQueues are specified in the following three rows.

SOCKET

Socket field description.

LAST RESET

Last reset state.

Translation rule address

Translation rule address in hex.

Tag name

Translation rule tag name.

Translation rule in_used

Translation rule in which the tag is used.

**** Xrule rule table *******

Beginning of the display for a specific rule.

Rule:x

Number of the rule.

in_used state:

Input-searched-pattern.

Match pattern:

Match pattern of the rule.

Sub pattern:

Substituted pattern.

Match type:

Match type.

Sub type:

Substituted pattern match type.