The following examples show output for the commands that can be used to verify X.25 version configuration.
show interfaces Sample Output: Example
Router# show interfaces serial 1/1
Serial1/1 is up, line protocol is up
Hardware is CD2430 in sync mode
Description: connected to stroll Serial1/1
Internet address is 1.0.0.2/8
MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation X25, loopback not set
X.25 DCE, version 1984, address 170092, state R1, modulo 8, timer 0
Defaults: idle VC timeout 0
cisco encapsulation
input/output window sizes 2/2, packet sizes 128/128
Timers: T10 60, T11 180, T12 60, T13 60
Channels: Incoming-only none, Two-way 10-100, Outgoing-only 200-210
RESTARTs 1/0 CALLs 0+0/0+0/0+0 DIAGs 0/0
LAPB DCE, state CONNECT, modulo 8, k 7, N1 12056, N2 20
.
.
.
show x25 profile Sample Output: Example
Router# show x25 profile profile1
X.25 profile name: profile1
PROFILE DTE, version 1993, address <none>, state R/Inactive, modulo 8, timer 0
Defaults: idle VC timeout 0
input/output window sizes 2/2, packet sizes 128/128
Timers: T20 180, T21 200, T22 180, T23 180
Channels: Incoming-only none, Two-way 1-1024, Outgoing-only none
show x25 context Sample Output: Examples
Router# show x25 context interface serial 1/1
X.25 DCE, version 1984, address 170092, state R1, modulo 8, timer 0
Defaults: idle VC timeout 0
cisco encapsulation
input/output window sizes 2/2, packet sizes 128/128
Timers: T10 60, T11 180, T12 60, T13 60
Channels: Incoming-only none, Two-way 10-100, Outgoing-only 200-210
RESTARTs 0/0 CALLs 0+0/0+0/0+0 DIAGs 0/0
LAPB DCE, state CONNECT, modulo 8, k 7, N1 12056, N2 20
T1 3000, T2 0, interface outage (partial T3) 0, T4 0
VS 2, VR 2, tx NR 2, Remote VR 2, Retransmissions 0
Queues: U/S frames 0, I frames 0, unack. 0, reTx 0
IFRAMEs 2/2 RNRs 0/0 REJs 0/0 SABM/Es 1/0 FRMRs 0/0 DISCs 0/0
Router# show x25 context xot
XOT
station DXE/DTE, version 1993, address <none>, state R1, modulo 8
Defaults: idle VC timeout 0
input/output window sizes 2/2, packet sizes 128/128
Timers: T20 180, T21 200, T22 180, T23 180
RESTARTs 0/0 CALLs 0+1/0+0/0+0 DIAGs 0/0
Router# show x25 context interface serial 1/0
Serial1/0 DLCI 16
PROFILE dxe/DTE, version 1993, address 2001510, state R1, modulo 8, timer 0
Defaults: idle VC timeout 0
input/output window sizes 2/2, packet sizes 128/128
Timers: T20 180, T21 200, T22 180, T23 180
Channels: Incoming-only none, Two-way 1-4095, Outgoing-only none
RESTARTs 0/0 CALLs 0+0/0+0/0+0 DIAGs 0/0
LAPB dxe/DTE, state CONNECT, modulo 8, k 7, N1 12056, N2 20
T1 3000, T2 0, interface outage (partial T3) 0, T4 0
VS 1, VR 1, tx NR 1, Remote VR 1, Retransmissions 0
Queues: U/S frames 0, I frames 0, unack. 0, reTx 0
IFRAMEs 1/1 RNRs 0/0 REJs 0/0 SABM/Es 1/0 FRMRs 0/0 DISCs 0/0