Contents

Implementing Quality of Service in a Wireless LAN

This module describes how to implement quality of service (QoS) features on a Cisco 800, 1800, 2800, or 3800 series integrated services router, hereafter referred to as an access point or AP.

QoS enables you to use congestion management and avoidance tools, which prevent traffic from slowing down on your wireless LAN (WLAN).

In a wired network, routers or switches primarily enforce QoS. In a WLAN, however, the access point manages QoS duties for traffic to wireless clients.

Without QoS, the access point offers best-effort service to each packet, regardless of the packet contents or size. It sends the packets without any assurance of reliability, delay bounds, or throughput.

Finding Feature Information in This Module

Your Cisco IOS software release may not support all of the features documented in this module. To reach links to specific feature documentation in this module and to see a list of the releases in which each feature is supported, use the Feature Information for Implementing Quality of Service in a Wireless LAN.

Finding Support Information for Platforms and Cisco IOS Software Images

Use Cisco Feature Navigator to find information about platform support and Cisco IOS software image support. Access Cisco Feature Navigator at http:/​/​www.cisco.com/​go/​fn . You must have an account on Cisco.com. If you do not have an account or have forgotten your username or password, click Cancel at the login dialog box and follow the instructions that appear.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/​go/​cfn. An account on Cisco.com is not required.

Prerequisites for Implementing QoS in a Wireless LAN

The following prerequisites apply to implementing QoS in a wireless LAN:

  • If you use VLANs on your wireless LAN, make sure the necessary VLANs are configured on your access point before configuring QoS.

  • Be familiar with the traffic on your wireless LAN. If you know the applications used by wireless client devices, the sensitivity of applications to delay, and the amount of traffic associated with the applications, configuring QoS improves performance.

  • QoS does not create additional bandwidth on a wireless LAN; it helps control the allocation of bandwidth. If there is enough bandwidth on your wireless LAN, it might not be necessary to configure QoS.

Information About Implementing QoS in a Wireless LAN

QoS for Wireless LANs

Typically, networks operate on a best-effort delivery basis, which means that all traffic has equal priority and an equal chance of being delivered in a timely manner. When congestion occurs, all traffic has an equal chance of being dropped.

When you configure QoS on the access point, you can select specific network traffic, prioritize it, and use congestion-management and congestion-avoidance techniques to provide preferential treatment. Implementing QoS in your wireless LAN makes network performance more predictable and bandwidth utilization more effective.

When you configure QoS, you create QoS policies and apply the policies to the VLANs configured on your access point. If you do not use VLANs on your network, you can apply your QoS policies to the access point’s Ethernet and radio ports.

QoS for Wireless LANs Compared to QoS on Wired LANs

The QoS implementation for wireless LANs differs from QoS implementations on other Cisco devices. With QoS enabled, access points have the following behavior:

  • They do not classify packets; they prioritize packets based on the Dynamic Host Configuration Protocol (DSCP) value, client type (such as a wireless phone), or the priority value in the 802.1q or 802.1p tag.

  • They do not match packets using access control lists (ACL); they use only Modular QoS CLI (MQC) class maps for matching clauses.

  • They do not construct internal DSCP values; they support mapping only by assigning IP DSCP, Precedence, or Protocol values to Layer 2 Class of Service (CoS) values.

  • They carry out Enhanced Distributed Coordination Function (EDCF) like queueing on the radio egress port only.

  • They do only First In First Out (FIFO) queueing on the Ethernet egress port.

  • They support only 802.1q/p tagged packets. Access points do not support Inter-Switch Link (ISL).

  • They support only MQC policy-map set cos action.

  • They prioritize the traffic from voice clients (such as Symbol phones) over traffic from other clients when the QoS Element for Wireless Phones feature is enabled.

  • They support Spectralink phones using the class-map IP protocol clause with the protocol value set to 119.

Impact of QoS on a Wireless LAN

Wireless LAN QoS features area subset of the 802.11e draft. QoS on wireless LANs provides prioritization of traffic from the access point over the WLAN based on traffic classification.

Just as in other media, you might not notice the effects of QoS on a lightly loaded wireless LAN. The benefits of QoS become more obvious as the load on the wireless LAN increases, keeping the latency, jitter, and loss for selected traffic types within an acceptable range.

QoS on the wireless LAN focuses on downstream prioritization from the access point. The figure below shows the upstream and downstream traffic flow.

Figure 1. Upstream and Downstream Traffic Flow

The radio downstream flow is traffic transmitted out the access point radio to a wireless client device. This traffic is the main focus for QoS on a wireless LAN.

The radio upstream flow is traffic transmitted out the wireless client device to the access point. QoS for wireless LANs does not affect this traffic.

The Ethernet downstream flow is traffic sent from a switch or a router to the Ethernet port on the access point. If QoS is enabled on the switch or router, the switch or router might prioritize and rate-limit traffic to the access point.

The Ethernet upstream flow is traffic sent from the access point Ethernet port to a switch or router on the wired LAN. The access point does not prioritize traffic that it sends to the wired LAN based on traffic classification.

Precedence of QoS Settings

When you enable QoS, the access point queues packets based on the CoS value for each packet. If a packet matches one of the filter types based on its current precedence, the packet is classified based on the matching filter and no other filters are applied.

There are three levels of precedence for QoS filters.

  • 0--Dynamically created VoIP client filter. Traffic from voice clients takes priority over other traffic regardless of other policy settings. This setting takes precedence over all other policies, second only to previously assigned packet classifications.

  • 1--User configured class-map match clause (except match any). QoS policies configured for and that apply to VLANs or to the access point interfaces are third in precedence after previously classified packets and the QoS element for wireless phones setting.

  • 2--User configured class-map match any clause (match VLAN). If a default classification for all packets on a VLAN is set, that policy is fourth in the precedence list.

Precedence number zero is the highest.

QoS Configuration Guidelines for Wireless LANs

An access point is essentially a Layer 2 transparent bridge between wired and wireless networks. Typically, bandwidth on the wireless side constrains the wired side. For example, 802.11b offers 6 Mbps half duplex and 100BASE-T offers 100 Mbps full duplex.

A Cisco access point uses ACLs for forwarding or blocking packets on selective basis, as designated by the user for the purpose of:

  • Providing QoS for Voice-over-IP (VoIP) phones.

  • Mapping IP precedence values into 802.1p/q CoS values for downlink traffic.

  • Providing Layer 2 and Layer 3 ACL features to the bridging path and access point host receive path.

802.11 VoIP Phone Support

The Symbol element is advertised by the access point. This helps a Symbol phone to make an association decision if there are multiple access points serving the area. The current packet rate is the calculation of average means of number of packets transmitted per second for the past 8 seconds.

After the normal 802.11 association process, a Symbol phone sends a proprietary Symbol 802.11 phone registration message (WNMP) to the access point to complete the association.

The Symbol phone does not associate to an access point if the advertised packet rate is above the threshold of the access point. The Symbol phone uses its Symbol element as optional information. Basic operation does not require an access point to send Symbol elements.

Cisco Wireless IP Phone 7920 Support

The wireless IP Phone 7920 uses Cisco Discovery Protocol (CDP) messages with Appliance VLAN-ID TLV to inform the access point of its presence. The access point intercepts the CDP messages sent from the client, and if it contains the Appliance VLAN-ID Type-Length-Value (TLV), it should flag the client as VoIP phone client.

If a VLAN is enabled, we recommend that all phone clients be associated to a single voice VLAN and that all data clients be associated to a separate data VLAN. If a VLAN is not enabled, we recommend that all the VoIP packets be classified by using the same user_priority value (6).

The access point always uses DIFS with minimum contention window (CW) value derived from the CWmax and CWmin range parameters to prioritize voice traffic.

The figure below shows the difference between traditional physical LAN segmentation and logical VLAN segmentation with wireless devices connected.

Figure 2. LAN and VLAN Segmentation with Wireless Devices

Radio Interface Transmit Queues

The access point radio maintains four priority queues, one for each traffic category, and 802.11e EDCF to provide differentiate Distributed Coordination Function (DCF) access to the wireless medium. An EDCF-aware access point is assigned distinct pairs of CWmin and CWmax parameters for each traffic category. The CWmin and CWmax parameters can be modified through the CLI.

Radio Access Categories

The access point uses the radio access categories to calculate backoff times for each packet. As a rule, high-priority packets have short backoff times.

The default values in the minimum and maximum contention window fields, and in the slot time fields, are based on settings recommended in IEEE Draft Standard 802.11e. For detailed information on these values, consult the standard.

We recommend that you use the default settings. Changing these values can lead to unexpected blockages of traffic on your wireless LAN, and the blockages might be difficult to diagnose.

Ethernet Interface Transmit Queue

Because the Ethernet interface always has a larger bandwidth than radio interface, there is no need to maintain priority queues for Ethernet interface. There will be only one transmit queue per Ethernet interface.

802.1Q Untagged Voice Packets

If a VLAN is enabled, Cisco IOS bridging code adds 802.11q tags into the untagged voice packets. The CoS value should be part of the VLAN configuration. For a voice VLAN, the CoS should be (6).

If a VLAN is not enabled, the access point relies on the DSCP-to-CoS filter configured by the user to assign CoS value to the packet.

CoS Values on a VLAN

The default CoS value for all the VLANs is zero (best effort). This ensures that the access point provides differentiate services based on VLAN IDs. Packets sent to these clients are queued into the appropriate priority queue based on their VLAN CoS value.

If a VLAN is enabled, and packets from a wireless client must be forwarded to the wired network, a 802.1q tag is added by the forwarding module.

Access Control Lists

ACLs are applied on either outbound or inbound interfaces. For standard inbound access lists, after receiving a packet, the Cisco IOS software checks the source address of the packet against the access list. If the access list permits the address, the software continues to process the packet. If the access list rejects the address, the software discards the packet and returns an Internet Control Message Protocol (ICMP) host unreachable message.

For extended access lists, the router also checks the destination access list. If the access list permits the address, the software continues to process the packet. If the access list rejects the address, the software discards the packet and returns an ICMP host unreachable message.

For standard outbound access lists, after receiving and routing a packet to a controlled interface, the software checks the source address of the packet against the access list. For extended access lists, the router also checks the destination access list. If the access list permits the address, the software sends the packet. If the access list rejects the address, the software discards the packet and returns an ICMP host unreachable message.

If the specified access list does not exist, all packets are passed.

When you enable outbound access lists, you automatically disable autonomous switching for that interface. When you enable input access lists on any CBus or CxBus interface, you automatically disable autonomous switching for all interfaces (with one exception--a Storage Services Enabler (SSE) configured with simple access lists can still switch packets, on output only).

When you apply an access list that has not yet been defined to an interface, the software will act as if the access list has not been applied to the interface and will accept all packets. Remember this behavior if you use undefined access lists as a means of security in your network.

Wi-Fi Multimedia Mode

When you enable QoS, the access point uses Wi-Fi Multimedia (WMM) mode by default. WMM provides these enhancements over basic QoS mode:

  • The access point adds each packet’s class of service to the packet’s 802.11 header to be passed to the receiving station.

  • Each access class has its own 802.11 sequence number. The sequence number allows a high-priority packet to interrupt the retries of a lower-priority packet without overflowing the duplicate checking buffer on the receiving side.

  • For access classes that are configured to allow it, transmitters that are qualified to transmit through the normal backoff procedure are allowed to send a set of pending packets during the configured transmit opportunity (a specific number of microseconds). Sending a set of pending packets improves throughput because each packet does not have to wait for a backoff to gain access; instead, the packets can be transmitted immediately one after the other.

The access point uses WMM enhancements in packets sent to client devices that support WMM. The access point applies basic QoS policies to packets sent to clients that do not support WMM.

To disable WMM, use the no dot11 qos mode wmm command in interface configuration mode.

How to Implement QoS on a Wireless LAN

Implementing QoS on a Wireless LAN

Perform this task to implement QoS features on a wireless LAN.

SUMMARY STEPS

    1.    enable

    2.    configure terminal

    3.    dot11 phone

    4.    interface dot11Radio interface

    5.    ip access-group {access-list-number | access-list-name} {in | out}

    6.    bridge-group bridge-group input-address-list access-list-number

    7.    l2-filter bridge-group-acl

    8.    traffic-class {best-effort | background | video | voice} [cw-min min-value | cw-max max-value | fixed-slot backoff-interval]

    9.    end

    10.    copy running-config startup-config


DETAILED STEPS
     Command or ActionPurpose
    Step 1 enable


    Example:
    Router> enable
     

    Enables privileged EXEC mode.

    • Enter your password if prompted.

     
    Step 2 configure terminal


    Example:
    Router# configure terminal
     

    Enters global configuration mode.

     
    Step 3 dot11 phone


    Example:
    Router(config)# dot11 phone
     

    Enables 802.11 compliance phone support.

     
    Step 4 interface dot11Radio interface


    Example:
    Router(config)# interface dot11Radio 0
     

    (Optional) Enters interface configuration mode for the radio interface.

     
    Step 5 ip access-group {access-list-number | access-list-name} {in | out}


    Example:
    Router(config-if)# ip access-group 101 out
     

    (Optional) Controls access to an interface.

    • The example shows how to apply access list 101 on packets outbound from an interface.

     
    Step 6 bridge-group bridge-group input-address-list access-list-number


    Example:
    Router(config-if)# bridge-group 1 input-address-list 700
     

    (Optional) Assigns an access list to a particular interface.

    • This access list is used to filter packets received on that interface based on their MAC source addresses.

     
    Step 7 l2-filter bridge-group-acl


    Example:
    Router(config-if)# l2-filter bridge-group-acl
     

    (Optional) Applies a Layer 2 ACL filter to bridge group incoming and outgoing packets between the access point and the host (upper layer).

    • If this command is enabled, and any Layer 2 ACLs are installed in ingress or egress, the same ACLs are applied to packets received or sent by the access point host stack.

     
    Step 8 traffic-class {best-effort | background | video | voice} [cw-min min-value | cw-max max-value | fixed-slot backoff-interval]


    Example:
    Router(config-if)# traffic-class best-effort cw-min 4 cw-max 10 fixed-slot 2
     

    (Optional) Configures the radio interface QoS traffic class parameters for each of the four traffic types.

    • Backoff parameters control how the radio accesses the airwaves. The cw-min and cw-max keywords specify the collision window as a power of 2. For example, if the value is set to 3, the contention window is 0 to 7 backoff slots (2 to the power 3 minus 1). The fixed-slot keyword specifies the number of backoff slots that are counted before the random backoff counter starts to count down.

     
    Step 9 end


    Example:
    Router(config-if)# end
     

    Returns to privileged EXEC mode.

     
    Step 10 copy running-config startup-config


    Example:
    Router# copy running-config startup-config
     

    Saves configuration changes to NVRAM so that they are not lost if there is a system reload or power outage.

     

    Configuration Examples for Implementing QoS on a Wireless LAN

    Configuring QoS on a Wireless LAN Example

    The following example shows how to:

    • Enable 802.11 compliance phone support.

    • Configure the best effort traffic class for contention windows and fixed-slot backoff values.

    Each time the backoff for best effort is started, the backoff logic waits a minimum of the 802.11 Short Inter-Frame Space (SIFS) time plus two backoff slots. It then begins counting down the 0 to 15 backoff slots in the contention window.

    • Save your entries in the configuration file.

    

    configure terminal
    

    	dot11 phone
    

    	interface dot11Radio 0/3/0
    

    	traffic-class best-effort cw-min 4 cw-max 10 fixed-slot 2
    

    	end
    

    	copy running-config startup-config
    

    

    

    Configuring QoS for a Voice VLAN on an Access Point in Routing Mode  Example
    

    
Using Configuring QoS for a Voice VLAN on an Access Point in Routing Mode Example as a reference, this example shows how to create a VLAN for voice traffic on an access point in routing mode and apply QoS parameters to that voice VLAN:
    

    

    configure terminal 
    

    	class-map match-any voice_vlan 
    

    	match vlan 2 
    

    	policy-map voice
	class voice_vlan
	set cos 6
    

    	exit
    

    	exit
    

    	interface Dot11Radio 0/3/0
	no ip address
	ssid serialvoicevlan
	vlan 2
	authentication open
    

    	exit
    

    	exit
    

    	interface Dot11Radio 0/3/0.2
	encapsulation dot1Q 2
	ip address 10.2.1.1 255.255.255.0
	service-policy output voice
    

    	end
    

    	copy running-config startup-config 
    

    

    

    

    Additional References
    

     
		
     The following sections provide references related to implementing QoS on a wireless LAN.
		
    
 
	 
    

    Related Documents
     
		 
		

     
					 
     Related Topic
					 
    
 
				      		
 
					 
     Document Title
					 
    
 
				      		

    
    

     
					 
     Cisco IOS bridging commands: complete command syntax, command mode, command history, defaults, usage guidelines, and examples
					 
    
 
				      		
 
					 
     
						Cisco IOS Bridging Command Reference 
					 
    
 
				      		

    

     
					 
     Cisco IOS wireless LAN commands: complete command syntax, command mode, command history, defaults, usage guidelines, and examples
					 
    
 
				      		
 
					 
     
						Cisco IOS Wireless LAN Command Reference
					 
    
 
				      		

    
    

    

    
 
	 
    

    Standards
     
		 
		

     
					 
     Standard
					 
    
 
				      		
 
					 
     Title
					 
    
 
				      		

    
    

     
					 
     No new or modified standards are supported, and support for existing standards has not been modified by this feature.
					 
    
 
				      		
 
					 
     --
					 
    
 
				      		

    
    

    

    
 
	 
    

    MIBs
     
		 
		

     
					 
     MIB
					 
    
 
				      		
 
					 
     MIBs Link
					 
    
 
				      		

    
    

     
					 
     No new or modified MIBs are supported, and support for existing MIBs has not been modified.
					 
    
 
				      		
 
					 
     To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at the following URL:
					 
    
 
					 
     
						http:/​/​www.cisco.com/​go/​mibs 
					 
    
 
				      		

    
    

    

    
 
	 
    

    RFCs
     
		 
		

     
					 
     RFC
					 
    
 
				      		
 
					 
     Title
					 
    
 
				      		

    
    

     
					 
     No new or modified RFCs are supported, and support for existing RFCs has not been modified.
					 
    
 
				      		
 
					 
     --
					 
    
 
				      		

    
    

    

    
 
	 
    

    Technical Assistance
     
		 
		

     
					 
     Description
					 
    
 
				      		
 
					 
     Link
					 
    
 
				      		

    
    

     
					 
     The Cisco Technical Support website contains thousands of pages of searchable technical content, including links to products, technologies, solutions, technical tips, and tools. Registered Cisco.com users can log in from this page to access even more content.
					 
    
 
				      		
 
					 
     
						http:/​/​www.cisco.com/​techsupport 
						 
					 
    
 
				      		

    
    

    

    
 
	 
    

    

    

    Feature Information for Implementing Quality of Service in a Wireless LAN
    

     
		
    The following table
		  provides release information about the feature or features described in this
		  module. This table lists only the software release that introduced support for
		  a given feature in a given software release train. Unless noted otherwise,
		  subsequent releases of that software release train also support that feature. 
		
    
 Use Cisco Feature Navigator to find information about platform
		support and Cisco software image support. To access Cisco Feature Navigator, go
		to 
		.
		An account on Cisco.com is not required. 
	 
    

     
		

    Table 1 Feature Information for Implementing Quality of Service in a Wireless LAN
     
				  
     Feature Name 
				  
    
 
				    		
 
				  
     Releases 
				  
    
 
				    		
 
				  
     Feature Information 
				  
    
 
				    		

    
    

     
				  
     Wi-Fi Multimedia (WMM) Required Elements 
				  
    
 
				  
     
				  
    
 
				    		
 
				  
     12.4(15)T 
				  
    
 
				    		
 
				  
     WMM provides enhancements over basic QoS mode. 
				  
    
 
				    		

    
    

    

    
 
	 
    

    

    

    


    
















Implementing Quality of Service in a Wireless LAN

                              

    


    Contents
    Implementing Quality of Service in a Wireless LAN
    

    
This module describes how to implement quality of service (QoS) features on a Cisco 800, 1800, 2800, or 3800 series integrated services router, hereafter referred to as an access point or AP.
    

    
QoS enables you to use congestion management and avoidance tools, which prevent traffic from slowing down on your wireless LAN (WLAN).
    

    
In a wired network, routers or switches primarily enforce QoS. In a WLAN, however, the access point manages QoS duties for traffic to wireless clients.
    

    
Without QoS, the access point offers best-effort service to each packet, regardless of the packet contents or size. It sends the packets without any assurance of reliability, delay bounds, or throughput.
    

    Finding Feature Information in This Module
    
      
      
    
        Your Cisco IOS software release may not support all of the features documented in this module. 
To reach links to specific feature documentation in this module and to see a list of the releases in which each feature is supported, use the Feature Information for Implementing Quality of Service in a Wireless LAN.
    

    
    

    Finding Support Information for Platforms and Cisco IOS Software Images
    
      
      
    
Use Cisco Feature Navigator to find information about platform support and Cisco IOS software image support. Access Cisco Feature Navigator at 
http:/​/​www.cisco.com/​go/​fn
. You must have an account on Cisco.com. If you do not have an account or have forgotten your username or password, click Cancel at the login dialog box and follow the instructions that appear. 
    

    
    

    

    Finding Feature Information
    

     Your software release may not support all the features documented in this module. For the latest caveats and feature information, see 
		Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table at the end of this module. 
	 
    

    Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to 
		www.cisco.com/​go/​cfn. An account on Cisco.com is not required. 
	 
    

    

    

    Prerequisites for Implementing QoS in a Wireless LAN
    

    
The following prerequisites apply to implementing QoS in a wireless LAN:
    

    • 
If you use VLANs on your wireless LAN, make sure the necessary VLANs are configured on your access point before configuring QoS.
      

      • 

    • 
Be familiar with the traffic on your wireless LAN. If you know the applications used by wireless client devices, the sensitivity of applications to delay, and the amount of traffic associated with the applications, configuring QoS improves performance.
      

      • 

    • 
QoS does not create additional bandwidth on a wireless LAN; it helps control the allocation of bandwidth. If there is enough bandwidth on your wireless LAN, it might not be necessary to configure QoS.
      

      • 

    

    

    

    Information About Implementing QoS in a Wireless LAN
    

    

    QoS for Wireless LANs
    

    
Typically, networks operate on a best-effort delivery basis, which means that all traffic has equal priority and an equal chance of being delivered in a timely manner. When congestion occurs, all traffic has an equal chance of being dropped.
    

    
When you configure QoS on the access point, you can select specific network traffic, prioritize it, and use congestion-management and congestion-avoidance techniques to provide preferential treatment. Implementing QoS in your wireless LAN makes network performance more predictable and bandwidth utilization more effective.
    

    
When you configure QoS, you create QoS policies and apply the policies to the VLANs configured on your access point. If you do not use VLANs on your network, you can apply your QoS policies to the access point’s Ethernet and radio ports.
    

    

    QoS for Wireless LANs Compared to QoS on Wired LANs
    

    
The QoS implementation for wireless LANs differs from QoS implementations on other Cisco devices. With QoS enabled, access points have the following behavior:
    

    • 
They do not classify packets; they prioritize packets based on the Dynamic Host Configuration Protocol (DSCP) value, client type (such as a wireless phone), or the priority value in the 802.1q or 802.1p tag.
      

      • 

    • 
They do not match packets using access control lists (ACL); they use only Modular QoS CLI (MQC) class maps for matching clauses.
      

      • 

    • 
They do not construct internal DSCP values; they support mapping only by assigning IP DSCP, Precedence, or Protocol values to Layer 2 Class of Service (CoS) values.
      

      • 

    • 
They carry out Enhanced Distributed Coordination Function (EDCF) like queueing on the radio egress port only.
      

      • 

    • 
They do only First In First Out (FIFO) queueing on the Ethernet egress port.
      

      • 

    • 
They support only 802.1q/p tagged packets. Access points do not support Inter-Switch Link (ISL).
      

      • 

    • 
They support only MQC policy-map set cos action.
      

      • 

    • 
They prioritize the traffic from voice clients (such as Symbol phones) over traffic from other clients when the QoS Element for Wireless Phones feature is enabled.
      

      • 

    • 
They support Spectralink phones using the class-map IP protocol clause with the protocol value set to 119.
      

      • 

    

    

    

    Impact of QoS on a Wireless LAN
    

     Wireless LAN QoS features area subset of the 802.11e draft. QoS on
		wireless LANs provides prioritization of traffic from the access point over the
		WLAN based on traffic classification.
	 
    

     Just as in other media, you might not notice the effects of QoS on a
		lightly loaded wireless LAN. The benefits of QoS become more obvious as the
		load on the wireless LAN increases, keeping the latency, jitter, and loss for
		selected traffic types within an acceptable range. 
	 
    

     QoS on the wireless LAN focuses on downstream prioritization from the
		access point. The figure below shows the upstream and downstream traffic flow.
	 
    

    Figure 1. Upstream and Downstream Traffic Flow

    

     The radio downstream flow is traffic transmitted out the access point
		radio to a wireless client device. This traffic is the main focus for QoS on a
		wireless LAN.
	 
    

     The radio upstream flow is traffic transmitted out the wireless client
		device to the access point. QoS for wireless LANs does not affect this traffic.
	 
    

     The Ethernet downstream flow is traffic sent from a switch or a router
		to the Ethernet port on the access point. If QoS is enabled on the switch or
		router, the switch or router might prioritize and rate-limit traffic to the
		access point.
	 
    

     The Ethernet upstream flow is traffic sent from the access point
		Ethernet port to a switch or router on the wired LAN. The access point does not
		prioritize traffic that it sends to the wired LAN based on traffic
		classification.
	 
    

    

    

    

    Precedence of QoS Settings
    

    
When you enable QoS, the access point queues packets based on the CoS value for each packet. If a packet matches one of the filter types based on its current precedence, the packet is classified based on the matching filter and no other filters are applied.
    

    
There are three levels of precedence for QoS filters. 
    

    • 
0--Dynamically created VoIP client filter. Traffic from voice clients takes priority over other traffic regardless of other policy settings. This setting takes precedence over all other policies, second only to previously assigned packet classifications. 
      

      • 

    • 
1--User configured class-map match clause (except match any). QoS policies configured for and that apply to VLANs or to the access point interfaces are third in precedence after previously classified packets and the QoS element for wireless phones setting.
      

      • 

    • 
2--User configured class-map match any clause (match VLAN). If a default classification for all packets on a VLAN is set, that policy is fourth in the precedence list.
      

      • 

    

    
Precedence number zero is the highest.
    

    

    

    QoS Configuration Guidelines for Wireless LANs
    

    
An access point is essentially a Layer 2 transparent bridge between wired and wireless networks. Typically, bandwidth on the wireless side constrains the wired side. For example, 802.11b offers 6 Mbps half duplex and 100BASE-T offers 100 Mbps full duplex. 
    

    
A Cisco access point uses ACLs for forwarding or blocking packets on selective basis, as designated by the user for the purpose of:
    

    • 
Providing QoS for Voice-over-IP (VoIP) phones.
      

      • 

    • 
Mapping IP precedence values into 802.1p/q CoS values for downlink traffic.
      

      • 

    • 
Providing Layer 2 and Layer 3 ACL features to the bridging path and access point host receive path. 
      

      • 

    

    

    802.11 VoIP Phone Support
    

    
The Symbol element is advertised by the access point. This helps a Symbol phone to make an association decision if there are multiple access points serving the area. The current packet rate is the calculation of average means of number of packets transmitted per second for the past 8 seconds.
    

    
After the normal 802.11 association process, a Symbol phone sends a proprietary Symbol 802.11 phone registration message (WNMP) to the access point to complete the association.
    

    
The Symbol phone does not associate to an access point if the advertised packet rate is above the threshold of the access point. The Symbol phone uses its Symbol element as optional information. Basic operation does not require an access point to send Symbol elements. 
    

    

    

    Cisco Wireless IP Phone 7920 Support
    

     The wireless IP Phone 7920 uses Cisco Discovery Protocol (CDP) messages
		with Appliance VLAN-ID TLV to inform the access point of its presence. The
		access point intercepts the CDP messages sent from the client, and if it
		contains the Appliance VLAN-ID Type-Length-Value (TLV), it should flag the
		client as VoIP phone client.
	 
    

     If a VLAN is enabled, we recommend that all phone clients be associated
		to a single voice VLAN and that all data clients be associated to a separate
		data VLAN. If a VLAN is not enabled, we recommend that all the VoIP packets be
		classified by using the same user_priority value (6).
	 
    

     The access point always uses DIFS with minimum contention window (CW)
		value derived from the CWmax and CWmin range parameters to prioritize voice
		traffic.
	 
    

     The figure below shows the difference between traditional physical LAN
		segmentation and logical VLAN segmentation with wireless devices connected.
	 
    

    Figure 2. LAN and VLAN Segmentation with Wireless Devices

    

    

    

    Radio Interface Transmit Queues
    

    
The access point radio maintains four priority queues, one for each traffic category, and 802.11e EDCF to provide differentiate Distributed Coordination Function (DCF) access to the wireless medium. An EDCF-aware access point is assigned distinct pairs of CWmin and CWmax parameters for each traffic category. The CWmin and CWmax parameters can be modified through the CLI.
    

    

    Radio Access Categories
    

    
The access point uses the radio access categories to calculate backoff times for each packet. As a rule, high-priority packets have short backoff times.
    

    
The default values in the minimum and maximum contention window fields, and in the slot time fields, are based on settings recommended in IEEE Draft Standard 802.11e. For detailed information on these values, consult the standard.
    

    
We recommend that you use the default settings. Changing these values can lead to unexpected blockages of traffic on your wireless LAN, and the blockages might be difficult to diagnose.
    

    

    

    

    

    Ethernet Interface Transmit Queue
    

    
Because the Ethernet interface always has a larger bandwidth than radio interface, there is no need to maintain priority queues for Ethernet interface. There will be only one transmit queue per Ethernet interface.
    

    

    802.1Q Untagged Voice Packets
    

    
If a VLAN is enabled, Cisco IOS bridging code adds 802.11q tags into the untagged voice packets. The CoS value should be part of the VLAN configuration. For a voice VLAN, the CoS should be (6). 
    

    
If a VLAN is not enabled, the access point relies on the DSCP-to-CoS filter configured by the user to assign CoS value to the packet. 
    

    

    

    CoS Values on a VLAN
    

    
The default CoS value for all the VLANs is zero (best effort). This ensures that the access point provides differentiate services based on VLAN IDs. Packets sent to these clients are queued into the appropriate priority queue based on their VLAN CoS value. 
    

    
If a VLAN is enabled, and packets from a wireless client must be forwarded to the wired network, a 802.1q tag is added by the forwarding module.
    

    

    

    

    Access Control Lists
    

    
ACLs are applied on either outbound or inbound interfaces. For standard inbound access lists, after receiving a packet, the Cisco IOS software checks the source address of the packet against the access list. If the access list permits the address, the software continues to process the packet. If the access list rejects the address, the software discards the packet and returns an Internet Control Message Protocol (ICMP) host unreachable message. 
    

    
For extended access lists, the router also checks the destination access list. If the access list permits the address, the software continues to process the packet. If the access list rejects the address, the software discards the packet and returns an ICMP host unreachable message. 

    

    
For standard outbound access lists, after receiving and routing a packet to a controlled interface, the software checks the source address of the packet against the access list. For extended access lists, the router also checks the destination access list. If the access list permits the address, the software sends the packet. If the access list rejects the address, the software discards the packet and returns an ICMP host unreachable message. 

    

    
If the specified access list does not exist, all packets are passed. 

    

    
When you enable outbound access lists, you automatically disable autonomous switching for that interface. When you enable input access lists on any CBus or CxBus interface, you automatically disable autonomous switching for all interfaces (with one exception--a Storage Services Enabler (SSE) configured with simple access lists can still switch packets, on output only).
    

    
When you apply an access list that has not yet been defined to an interface, the software will act as if the access list has not been applied to the interface and will accept all packets. Remember this behavior if you use undefined access lists as a means of security in your network. 
    

    

    

    Wi-Fi Multimedia Mode
    

    
When you enable QoS, the access point uses Wi-Fi Multimedia (WMM) mode by default. WMM provides these enhancements over basic QoS mode:
    

    • 
The access point adds each packet’s class of service to the packet’s 802.11 header to be passed to the receiving station. 
      

      • 

    • 
Each access class has its own 802.11 sequence number. The sequence number allows a high-priority packet to interrupt the retries of a lower-priority packet without overflowing the duplicate checking buffer on the receiving side. 
      

      • 

    • 
For access classes that are configured to allow it, transmitters that are qualified to transmit through the normal backoff procedure are allowed to send a set of pending packets during the configured transmit opportunity (a specific number of microseconds). Sending a set of pending packets improves throughput because each packet does not have to wait for a backoff to gain access; instead, the packets can be transmitted immediately one after the other.
      

      • 

    

    
The access point uses WMM enhancements in packets sent to client devices that support WMM. The access point applies basic QoS policies to packets sent to clients that do not support WMM.
    

    
To disable WMM, use the no dot11 qos mode wmm command in interface configuration mode.
    

    

    

    

    How to Implement QoS on a Wireless LAN
    

    
	 
    

    

    Implementing QoS on a Wireless LAN
    

    
      
    
Perform this task to implement QoS features on a wireless LAN.
    

    
    
SUMMARY STEPS
      1.   
      
          
            enable
          
        
      

      2.   
      
          
            configure
          
          
            terminal
          
        
      

      3.   
      
          
            dot11
            phone
          
        
      

      4.   
      
          
            interface
            dot11Radio
          
          
            interface
          
        
      

      5.   
      
          
            ip
            access-group
           {access-list-number | access-list-name} {in | out}
      

      6.   
      
          
            bridge-group
          
          
            bridge-group
          
          
            input-address-list
          
          
            access-list-number
          
        
      

      7.   
      
          
            l2-filter
            bridge-group-acl
          
        
      

      8.   
      
          
            traffic-class
            {best-effort
            |
            background
            |
            video
            |
            voice}
            [cw-min
            min-value
            |
            cw-max
            max-value
            |
            fixed-slot
            backoff-interval]
          
        
      

      9.   
      
          
            end
          
        
      

      10.   
      
          
            copy
            running-config
            startup-config
          
        
      


    DETAILED STEPS
       Command or ActionPurpose
      Step 1
          
            enable
          
        
       

      Example:
      
          
      Router> enable
      

        
      
 
            		 
          
      
Enables privileged EXEC mode. 
      

          
      • 
Enter your password if prompted.
        

        • 

      

         
      
      

      Step 2
          
            configure
          
          
            terminal
          
        
       

      Example:
      
          
      Router# configure terminal
      

        
      
 
            		 
          
      
Enters global configuration mode.
      

         
      
      

      Step 3
          
            dot11
            phone
          
        
       

      Example:
      
          
      Router(config)# dot11 phone
      

        
      
 
            		 
          
      
Enables 802.11 compliance phone support.
      

         
      
      

      Step 4
          
            interface
            dot11Radio
          
          
            interface
          
        
       

      Example:
      
          
      Router(config)# interface dot11Radio 0
      

        
      
 
            		 
          
      
(Optional) Enters interface configuration mode for the radio interface.
      

         
      
      

      Step 5
          
            ip
            access-group
           {access-list-number | access-list-name} {in | out}
       

      Example:
      
          
      Router(config-if)# ip access-group 101 out
      

        
      
 
            		 
          
      
(Optional) Controls access to an interface.
      

          
      • 
The example shows how to apply access list 101 on packets outbound from an interface.
        

        • 

      

         
      
      

      Step 6
          
            bridge-group
          
          
            bridge-group
          
          
            input-address-list
          
          
            access-list-number
          
        
       

      Example:
      
          
      Router(config-if)# bridge-group 1 input-address-list 700
      

        
      
 
            		 
          
      
(Optional) Assigns an access list to a particular interface.
      

          
      • 
This access list is used to filter packets received on that interface based on their MAC source addresses.
        

        • 

      

         
      
      

      Step 7
          
            l2-filter
            bridge-group-acl
          
        
       

      Example:
      
          
      Router(config-if)# l2-filter bridge-group-acl
      

        
      
 
            		 
          
      
(Optional) Applies a Layer 2 ACL filter to bridge group incoming and outgoing packets between the access point and the host (upper layer).
      

          
      • 
If this command is enabled, and any Layer 2 ACLs are installed in ingress or egress, the same ACLs are applied to packets received or sent by the access point host stack.
        

        • 

      

         
      
      

      Step 8
          
            traffic-class
            {best-effort
            |
            background
            |
            video
            |
            voice}
            [cw-min
            min-value
            |
            cw-max
            max-value
            |
            fixed-slot
            backoff-interval]
          
        
       

      Example:
      
          
      Router(config-if)# traffic-class best-effort cw-min 4 cw-max 10 fixed-slot 2
      

        
      
 
            		 
          
      
(Optional) Configures the radio interface QoS traffic class parameters for each of the four traffic types.
      

          
      • 
Backoff parameters control how the radio accesses the airwaves. The cw-min and cw-max keywords specify the collision window as a power of 2. For example, if the value is set to 3, the contention window is 0 to 7 backoff slots (2 to the power 3 minus 1). The fixed-slot keyword specifies the number of backoff slots that are counted before the random backoff counter starts to count down.
        

        • 

      

         
      
      

      Step 9
          
            end
          
        
       

      Example:
      
          
      Router(config-if)# end
      

        
      
 
            		 
          
      
Returns to privileged EXEC mode. 
      

         
      
      

      Step 10
          
            copy
            running-config
            startup-config
          
        
       

      Example:
      
          
      Router# copy running-config startup-config
      

        
      
 
            		 
          
      
Saves configuration changes to NVRAM so that they are not lost if there is a system reload or power outage.
      

         
      
      

      

      

      

      

      Configuration Examples for Implementing QoS on a Wireless LAN
      

       
	 
      

      

      Configuring QoS on a Wireless LAN  Example
      

      
The following example shows how to:
      

      • 
Enable 802.11 compliance phone support.
        

        • 

      • 
Configure the best effort traffic class for contention windows and fixed-slot backoff values. 
        

        • 

      

      
Each time the backoff for best effort is started, the backoff logic waits a minimum of the 802.11 Short Inter-Frame Space (SIFS) time plus two backoff slots. It then begins counting down the 0 to 15 backoff slots in the contention window.
      

      • 
Save your entries in the configuration file.
        

        • 

      

      

      configure terminal
      

      	dot11 phone
      

      	interface dot11Radio 0/3/0
      

      	traffic-class best-effort cw-min 4 cw-max 10 fixed-slot 2
      

      	end
      

      	copy running-config startup-config
      

      

      

      Configuring QoS for a Voice VLAN on an Access Point in Routing Mode  Example
      

      
Using Configuring QoS for a Voice VLAN on an Access Point in Routing Mode Example as a reference, this example shows how to create a VLAN for voice traffic on an access point in routing mode and apply QoS parameters to that voice VLAN:
      

      

      configure terminal 
      

      	class-map match-any voice_vlan 
      

      	match vlan 2 
      

      	policy-map voice
	class voice_vlan
	set cos 6
      

      	exit
      

      	exit
      

      	interface Dot11Radio 0/3/0
	no ip address
	ssid serialvoicevlan
	vlan 2
	authentication open
      

      	exit
      

      	exit
      

      	interface Dot11Radio 0/3/0.2
	encapsulation dot1Q 2
	ip address 10.2.1.1 255.255.255.0
	service-policy output voice
      

      	end
      

      	copy running-config startup-config 
      

      

      

      

      Additional References
      

       
		
       The following sections provide references related to implementing QoS on a wireless LAN.
		
      
 
	 
      

      Related Documents
       
		 
		

       
					 
       Related Topic
					 
      
 
				        		
 
					 
       Document Title
					 
      
 
				        		

      
      

       
					 
       Cisco IOS bridging commands: complete command syntax, command mode, command history, defaults, usage guidelines, and examples
					 
      
 
				        		
 
					 
       
						Cisco IOS Bridging Command Reference 
					 
      
 
				        		

      

       
					 
       Cisco IOS wireless LAN commands: complete command syntax, command mode, command history, defaults, usage guidelines, and examples
					 
      
 
				        		
 
					 
       
						Cisco IOS Wireless LAN Command Reference
					 
      
 
				        		

      
      

      

      
 
	 
      

      Standards
       
		 
		

       
					 
       Standard
					 
      
 
				        		
 
					 
       Title
					 
      
 
				        		

      
      

       
					 
       No new or modified standards are supported, and support for existing standards has not been modified by this feature.
					 
      
 
				        		
 
					 
       --
					 
      
 
				        		

      
      

      

      
 
	 
      

      MIBs
       
		 
		

       
					 
       MIB
					 
      
 
				        		
 
					 
       MIBs Link
					 
      
 
				        		

      
      

       
					 
       No new or modified MIBs are supported, and support for existing MIBs has not been modified.
					 
      
 
				        		
 
					 
       To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at the following URL:
					 
      
 
					 
       
						http:/​/​www.cisco.com/​go/​mibs 
					 
      
 
				        		

      
      

      

      
 
	 
      

      RFCs
       
		 
		

       
					 
       RFC
					 
      
 
				        		
 
					 
       Title
					 
      
 
				        		

      
      

       
					 
       No new or modified RFCs are supported, and support for existing RFCs has not been modified.
					 
      
 
				        		
 
					 
       --
					 
      
 
				        		

      
      

      

      
 
	 
      

      Technical Assistance
       
		 
		

       
					 
       Description
					 
      
 
				        		
 
					 
       Link
					 
      
 
				        		

      
      

       
					 
       The Cisco Technical Support website contains thousands of pages of searchable technical content, including links to products, technologies, solutions, technical tips, and tools. Registered Cisco.com users can log in from this page to access even more content.
					 
      
 
				        		
 
					 
       
						http:/​/​www.cisco.com/​techsupport 
						 
					 
      
 
				        		

      
      

      

      
 
	 
      

      

      

      Feature Information for Implementing Quality of Service in a Wireless LAN
      

       
		
      The following table
		  provides release information about the feature or features described in this
		  module. This table lists only the software release that introduced support for
		  a given feature in a given software release train. Unless noted otherwise,
		  subsequent releases of that software release train also support that feature. 
		
      
 Use Cisco Feature Navigator to find information about platform
		support and Cisco software image support. To access Cisco Feature Navigator, go
		to 
		.
		An account on Cisco.com is not required. 
	 
      

       
		

      Table 1 Feature Information for Implementing Quality of Service in a Wireless LAN
       
				  
       Feature Name 
				  
      
 
				      		
 
				  
       Releases 
				  
      
 
				      		
 
				  
       Feature Information 
				  
      
 
				      		

      
      

       
				  
       Wi-Fi Multimedia (WMM) Required Elements 
				  
      
 
				  
       
				  
      
 
				      		
 
				  
       12.4(15)T 
				  
      
 
				      		
 
				  
       WMM provides enhancements over basic QoS mode.