- Configuring ATM
- ATM Conditional Debug Support
- ATM OAM Ping
- ATM OAM Traffic Reduction
- Local Template-Based ATM PVC Provisioning
- ATM PVC Range
- ATM SNMP Trap and OAM Enhancements
- ATM PVC F5 OAM Recovery Traps
- ATM VP Average Traffic Rate
- ATM Hierarchical Shaping�ATM VC into VP Shaping
- Autosense of MUX/SNAP Encapsulation and PPPoA/PPPoE on ATM PVCs
ATM VP Average Traffic Rate
The ATM VP Average Traffic Rate feature is a subscriber and VP traffic reporting feature that enables you to display the 5-minute traffic rates on virtual path (VP) counters.
Finding Feature Information
For the latest feature information and caveats, see the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the "Feature Information for ATM VP Average Traffic Rate" section.
Use Cisco Feature Navigator to find information about platform support and Cisco IOS XE software image support. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.
Contents
•Information About the ATM VP Average Traffic Rate Feature
•How to Display ATM VP Average Traffic Rates
•Configuration Examples for ATM VP Average Traffic Rates
•Feature Information for ATM VP Average Traffic Rate
Information About the ATM VP Average Traffic Rate Feature
ATM VP Average Traffic Rate
The ATM VP Average Traffic Rate feature is a subscriber and VP traffic reporting feature that enables you to display the 5-minute traffic rates on virtual path (VP) counters. This feature extends the show atm vp command to provide rate information. Minute counters on the ATM VPs support the show atm vp command.
The ATM VP Average Traffic Rate feature provides support for VP-based rate counters and enables you to display the average traffic load on the VP for the last 5 minutes. This feature is enabled by default and requires no configuration. The duration of the counters is set at 5 minutes average.
How to Display ATM VP Average Traffic Rates
•Displaying ATM VP 5-Minute Traffic Rates
Displaying ATM VP 5-Minute Traffic Rates
To display the 5-minute traffic rates, use the following command in privileged EXEC mode:
Configuration Examples for ATM VP Average Traffic Rates
ATM VP 5-Minute Traffic Rates: Example
ATM VP 5-Minute Traffic Rates: Example
The following example shows sample output from the show atm vp command. The output displays the 5-minute traffic rates for VP 10:
Router# show atm vp 10
ATM1/1/0 VPI: 10, PeakRate: 100000, CesRate: 0, DataVCs: 1, CesVCs: 0, Status: INACTIVE VCD VCI Type InPkts OutPkts AAL/Encap Status 1 3 PVC 0 0 F4 OAM INACTIVE 2 4 PVC 0 0 F4 OAM INACTIVE 3 100 PVC 78310 78310 AAL5-SNAP ACTIVE TotalInPkts: 78310, TotalOutPkts: 78310, TotalInFast: 0, TotalOutFast: 0, TotalBroadcasts:
5 Min Average Output Rate: 0 packets/sec, 32 bits/sec
TotalInPktDrops: 0, TotalOutPktDrops: 0
Total subscribed rate of active VC's: 0
Additional References
Related Documents
|
|
---|---|
show atm vp command |
Cisco IOS Asynchronous Transfer Mode Command Reference |
MIBs
Technical Assistance
Feature Information for ATM VP Average Traffic Rate
Table 1 lists the features in this module and provides links to specific configuration information.
Use Cisco Feature Navigator to find information about platform support and software image support. Cisco Feature Navigator enables you to determine which Cisco IOS XE software images support a specific software release, feature set, or platform. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.
Note Table 1 lists only the Cisco IOS XE software release that introduced support for a given feature in a given Cisco IOS XE software release train. Unless noted otherwise, subsequent releases of that Cisco IOS XE software release train also support that feature.