show pxf accounting

To show Parallel eXpress Forwarding (PXF) switching statistics for individual interfaces, use the show pxf accounting command in user EXEC or privileged EXEC mode.

show pxf accounting interface [slot/port]

Syntax Description

interface

Specifies the type of interface to display.

slot/

(Optional) Backplane slot number. On the Cisco 7200 VXR series routers, the value can be from 0 to 6.

port

(Optional) Port number of the interface. On the Cisco 7200 VXR series routers, the value can be from 0 to 5.


Command Modes

User EXEC (>)
Privileged EXEC (#)

Command History

Release
Modification

12.1(1)E

This command was introduced.

12.1(5)T

This command was integrated into Cisco IOS Release 12.1(5)T.'

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.2SX

This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.


Usage Guidelines

You can display information about the interface types shown in Table 83 using the show pxf accounting command:

Table 83 show pxf accounting Interface Types

Keyword
Interface Type

atm

ATM interface

ethernet

Ethernet interface

fastethernet

FastEthernet interface

hssi

High Speed Serial interface

null

Null interface

pos

Packet-over-SONET interface

serial

Synchronous serial interface

summary

PXF summary statistics


Examples

The following is sample output from the show pxf accounting ? command:

Router# show pxf accounting ?

  ATM           ATM interface
  Ethernet      IEEE 802.3
  FastEthernet  FastEthernet IEEE 802.3
  Hssi          High Speed Serial Interface
  Null          Null interface
  POS           Packet over Sonet
  Serial        Serial
  summary       PXF summary statistics

The following is sample output from the show pxf accounting ethernet command with an Ethernet interface in slot 4 on a Cisco 7200 VXR series router:

Router# show pxf accounting ethernet 4/0

Interface    Pkts In   Chars In   Pkts Out  Chars Out     Punted     Dropped
Ethernet4/0    0          0        122      11490          4          0

The following is sample output from the show pxf accounting null command with a null interface in slot 0 on a Cisco 7200 VXR series router:

Router# show pxf accounting null 0/0

Interface    Pkts In   Chars In   Pkts Out  Chars Out     Punted    Dropped
nu0/0          0          0          0          0       4932          0

The following is sample output from the show pxf accounting pos command with a Packet-over-SONET interface in slot 4 on a Cisco 7200 VXR series router:

Router# show pxf accounting pos

Interface    Pkts In   Chars In   Pkts Out  Chars Out     Punted    Dropped
POS4/0          19       1064         0          0         44         0

The following is sample output from the show pxf accounting serial command with a serial interface in slot 5 on a Cisco 7200 VXR series router:

Router# show pxf accounting serial 5/0

		Interface    Pkts In   Chars In   Pkts Out  Chars Out     Punted    Dropped
	Serial5/0          0          0          0          0          0       0

The following is sample output from the show pxf accounting summary command:

Router# show pxf accounting summary

            Pkts        Dropped   RP Processed        Ignored
           Total              0          48360              0

PXF Statistic:
Packets RP -> PXF:
    switch ip:                 0
    switch raw:         30048360
    qos fastsend:              0
    qos enqueue:            1938
Total:                  30050298

Packets PXF -> RP:
    qos pkts:               1938
    fast pkts:          30000000
    drops:total                0
    punts:total            48360
      "    not IP            :      40572
      "    CEF no adjacency  :       7788
Total:                  30050298

Packets ignored:               0     |    ring space:
    shadow ring full:          0     |        shadow ring:           16384
    in ring full:              0     |        inring:                  968
    PXF inactive:              0

tx credits:             16230330     |    delayed credits:               0
holdq enqueues:                0     |    requeue drops:                 0
interrupts:                40538     |    interrupt misses:           1947
interrupt packets:         53326
pending read bytes:            0

     Interface    Pkts In   Chars In   Pkts Out  Chars Out     Punted    Dropped
         Fa0/0          0          0   30000000 1740000000        970          0
         Et1/0          0          0          0          0      21309          0
         Et1/1          0          0          0          0          0          0
         Et1/2          0          0          0          0          0          0
         Et1/3          0          0          0          0          0          0
         Se2/0          0          0          0          0        963          0
         Se2/1          0          0          0          0          0          0
         Se2/2          0          0          0          0          0          0
         Se2/3          0          0          0          0          0          0
         Fa3/0          0          0          0          0        963          0
         PO4/0   30000000 1440000000          0          0        963          0
         AT5/0          0          0          0          0      23192          0
           Vi1          0          0          0          0          0          0
           Vt1          0          0          0          0          0          0
           Vi2          0          0          0          0          0          0

Related Commands

Command
Description

show pxf crash

Displays PXF crash information.

show pxf feature

Displays the PXF routing feature tables for enabled PXF features.

show pxf interface

Displays a summary of the interfaces in the router and the PXF features or capabilities enabled on these interfaces.


show pxf cpu access-lists

To display Parallel eXpress Forwarding (PXF) memory information for access control lists (ACLs), use the show pxf cpu access-lists command in privileged EXEC mode.

show pxf cpu access-lists [security | qos | pbr | compiled]

Cisco 10000 Series Router

show pxf cpu access-lists [security [ [tcam acl-name [detail] ] | flex-sum | children] | qos | pbr | compiled]

Syntax Description

security

(Optional) Displays information about the security ACLs defined in Cisco IOS and compiled to the PXF. Also displays information about split ACLs, such as how much memory has been used.

tcam acl-name

(Optional) Displays information about the specified security ACL stored in ternary content addressable memory (TCAM).

This option is only available on the PRE3 for the Cisco 10000 series router.

detail

(Optional) Displays decoded information about the packet fields used for matching in the TCAM.

flex-sum

(Optional) Displays summary information describing the amount of memory allocated in the parallel express forwarding (PXF) engine for use by the flexible key construction microcode. This information is useful for design teams.

This option is only available on the PRE3 for the Cisco 10000 series router.

children

(Optional) Displays information for child policies. If an ACL is a template child, the output typically does not display the child information. Specifying the children keyword displays data for child policies, too, and shows the children and the parent policy of each child.

Use caution when using the children keyword as there might be thousands of child policies configured, which could have negative effects on the command output.

qos

(Optional) Displays information about the QoS ACLs defined in Cisco IOS and compiled to the PXF.

pbr

(Optional) Displays information about ACLs for policy-based routing (PBR).

compiled

(Optional)  Displays information for all compiled Turbo-ACLs.

The PRE2 supports Turbo-ACLs and the compiled option. The PRE3 accepts the PRE2 compiled option, but does not implement Turbo-ACLs.


Command Modes

Privileged EXEC (#)

Command History

Release
Modification

12.2S

This command was introduced.

12.3(7)XI1

This command was introduced on the PRE2 for the Cisco 10000 series router.

12.2(31)SB2

This command was introduced on the PRE3 for the Cisco 10000 series router.


Usage Guidelines

Cisco 10000 Series Router (PRE2)

Because memory is shared between TurboACLs and MiniACLs, they can interfere with each other's capacities. The Mini-ACL is automatically set up with space for 8191 Mini-ACLs at router start. If more than 8191 Mini-ACLs are created, another block of MiniACLs (4096) is allocated. This process is repeated as necessary until the router is out of External Column Memory (XCM) in any one bank that the Mini-ACLs need.

Cisco 10000 Series router (PRE3)

The PRE3 implements only TCAM ACLs. Turbo-ACLs and Mini-ACLs are not supported.

Examples

The sample output from the show pxf cpu access-lists security command (see Sample Output) is based on the configuration of the access control list (ACL) called test_list (see ACL Configuration). The sample output is divided into several sections with a description of the type of information displayed in each.

ACL Configuration

Router# show pxf cpu access-lists test_list

Extended IP access list test_list (Compiled)
    10 permit ip any host 10.1.1.1
    20 permit ip any host 10.1.1.2
    30 permit ip any host 10.1.1.3
    40 permit ip any host 10.1.1.4
    50 permit ip any host 10.1.1.5
    60 permit ip any host 10.1.1.6
    70 permit ip any host 10.1.1.7
    80 permit ip any host 10.1.1.8
    90 permit ip any host 10.1.1.9
    100 permit ip any host 10.1.1.11
    110 permit ip any host 10.1.1.12

Sample Output

The following sample output describes the information displayed in the first section of the command output from the show pxf cpu access-lists security command:

Router# show pxf cpu access-lists security

PXF Security ACL statistics:
ACL            State      Tables  Entries  Config  Fragment  Redundant  Memory ACL_index
 1            Operational   1        -       -        -        -         0Kb     1
sl_def_acl    Operational   2        -       -        -        -         0Kb     2
test          Operational   3        -       -        -        -         0Kb     3
test_list     Operational   1        12      11       0        0         7Kb     1

Table 84, Part 1, describes the significant fields shown in the display.

Table 84, Part 1 show pxf cpu access-lists security Field Descriptions 

Field
Description

ACL

Identifies the ACL by name or number.

State

Displays the current state of the ACL:

Copying—ACL is in the process of being created or compiled.

Operational—ACL is active and filtering packets.

Out of acl private mem—ACL has run out of the private memory that was allocated exclusively to it.

Out of shared mem—ACL has run out of the memory that it shares with other ACLs.

Unknown Failure—ACL has failed because of an uncategorized reason.

Unneeded—ACL was allocated but is not currently in use.

Tables

An indicator of whether the ACL has been split into more than one PXF pass. The first three ACLs in the output are MiniACLs, and have the ACL_index duplicated in the Tables column.

Entries

The count of ACL rules as seen by the Turbo compiler. This is the sum of the Config, Fragment, and Redundant columns plus 1.

Config

The count of rules for this ACL.

Fragment

The count of extra rules added to handle fragment handling, where Layer 4 information is needed but not available in a packet fragment.

Redundant

The count of rules that are not needed because they are covered by earlier rules.

Memory

The amount of PXF XCM in use for the ACL.

ACL_index

The index of the ACL in XCM.


The following sample output describes the information displayed in the next section of the command output from the show pxf cpu access-lists security command:

First level lookup tables:
Block      Use              Rows       Columns   Memory used
  0   TOS/Protocol            1/128     1/32      16384
  1   IP Source (MS)          1/128     1/32      16384
  2   IP Source (LS)          1/128     1/32      16384
  3   IP Dest (MS)            2/128     1/32      16384
  4   IP Dest (LS)           12/128     1/32      16384
  5   TCP/UDP Src Port        1/128     1/32      16384
  6   TCP/UDP Dest Port       1/128     1/32      16384
  7   TCP Flags/Fragment      1/128     1/32      16384

Table 84, Part 2, describes the significant fields shown in the display.

Table 84, Part 2 show pxf cpu access-lists security Field Descriptions

Field
Description

Block

Indicates the block number.

Use

Describes the IP packet field that is being matched.

Rows

An indication of where the largest variety of values are in use in the ACLs that are being applied. In the output, 12/128 means that there are 12 different values of significance in the field. If there are other rules added and the value exceeds 128, more memory will be needed to accommodate the new rules.

Columns

An indication of the number of TurboACLs in PXF memory. In the output, 1/32 means there is only one TurboACL in PXF memory. If there are more than 31 added, another chunk of memory is needed to accommodate the new ACLs.

Memory used

Displays the total amount of memory used for this particular lookup table.


The following sample output describes the information displayed in the next section of the command output from the show pxf cpu access-lists security command. There are 16 banks of XCM in each PXF column. This output section shows the usage level of each bank.


Banknum   Heapsize   Freesize  %Free
   0       4718592    4702208    99
   1       8126464    6012928    73
   2       8388608    6290432    74
   3       8388608    6290432    74
   4       5898240    5881856    99
   5       8126464    6012928    73
   6       8388608    6290432    74
   7       8126464    6012928    73
   8       4456448    4440064    99
   9       8126464    6012928    73

Table 84, Part 3, describes the significant fields shown in the display.

Table 84, Part 3 show pxf cpu access-lists security Field Descriptions 

Field
Description

Banknum

The block of memory used for this particular lookup table.

Heapsize

The total amount of memory, in bytes, allocated for this block.

Freesize

The amount of memory, in bytes, that is currently available for use by this block of memory.

%Free

The percentage of memory that is free and available for use for this block of memory. When the %Free drops to 0, the router cannot hold any more ACLs in PXF memory, and any new ACL will not pass traffic.


This section of the sample command output indicates the memory usage of the MiniACLs in the router. All of the rows state about the same thing. To determine the actual number of MiniACLs in play, divide the memory used in any of blocks 1 to 10 by 256, or blocks 11 to 14 by 16.


MiniACL XCM Tables:
Block   Use               Memory Used   %Free
  0   IP Src 1                 768        99
  1   IP Src 2                 768        99
  2   IP Src 3                 768        99
  3   IP Src 4                 768        99
  4   IP Dest 1                768        99
  5   IP Dest 2                768        99
  6   IP Dest 3                768        99
  7   IP Dest 4                768        99
  8   ToS                      768        99
  9   Protocol                 768        99
  10  TCP Flags/Fragment       768        99
  11  Source Port 1             48        99
  12  Source Port 2             48        99
  13  Destination Port 2        48        99
  14  Destination Port 2        48        99

The following describes the information displayed in the last section of the sample output from the show pxf cpu access-lists security command:

Available MiniACL count = 8191
Usable ranges(inclusive):
1->8191

Table 84, Part 4, describes the significant fields shown in the display.

Table 84, Part 4 show pxf cpu access-lists security Field Descriptions

Field
Description

Available MiniACL

The number of ACLs currently available for allocation in XCM.

Usable ranges

The ACL indexes that will be assigned to MiniACLs.


PRE2 and PRE3 Security ACLs Examples (Cisco 10000 Series Router)

This section compares the output from the show pxf cpu access-lists security command when issued on the PRE2 and PRE3.

For the PRE2, the following sample output displays VMR (value, plus a mask and result) data for the ACL named ICMP_IGMP_MATCH:

Router# show pxf cpu access-lists security tcam ICMP_IGMP_MATCH detail 

-------------------------------------------------------------
VMR Format - handle: 524607B4
Format has 5 fields, refcount = 1
Field: Format, FIXED, start_bit = 69, end_bit = 71
Field: ACL index, FIXED, start_bit = 54, end_bit = 68
Field: Flags, FIXED, start_bit = 43, end_bit = 53
Field: L4 proto, FIXED CNV, start_bit = 16, end_bit = 23
Field: L4 source port, FIXED CNV, start_bit = 0, end_bit = 15 Total bits = 53, format = 72 
GMR used: 5 Col 2 LKBP Vector: 544
-------------------------------------------------------------
VMRs
------ VMR 0 ------
V: 001B0000 0000010B 00
M: FFFFC000 0000FFFF FF
R: 00010001
Format: 00000000/00000007
ACL index: 0000006C/00007FFF
L4 source port: 00000B00/0000FFFF
L4 proto: 00000001/000000FF
Flags: 00000000/00000000
------ VMR 1 ------
V: 001B0000 00000103 01
M: FFFFC000 0000FFFF FF
R: 00010002
Format: 00000000/00000007
ACL index: 0000006C/00007FFF
L4 source port: 00000301/0000FFFF
L4 proto: 00000001/000000FF
Flags: 00000000/00000000
------ VMR 2 ------
V: 001B0000 00000213 00
M: FFFFC000 0000FFFF 00
R: 00010003
Format: 00000000/00000007
ACL index: 0000006C/00007FFF
L4 source port: 00001300/0000FF00
L4 proto: 00000002/000000FF
Flags: 00000000/00000000
------ VMR 3 ------
V: 001B0000 00000214 00
M: FFFFC000 0000FFFF 00
R: 00010004
Format: 00000000/00000007
ACL index: 0000006C/00007FFF
L4 source port: 00001400/0000FF00
L4 proto: 00000002/000000FF
Flags: 00000000/00000000

For the PRE3, the following sample output displays for the show pxf cpu access-lists security command. Notice that the output does not include the columns shown above that are relevant to only the PRE2 and the output no longer displays first-level lookup tables.

Router# show pxf cpu access-lists security 

PXF Security ACL statistics:
 ACL                                     State           ACL_index
STANDARD_MATCH_PERMIT                    Operational           116
SRC_IP_MATCH144                          Operational           102
DST_IP_MATCH                             Operational           113
DST_IP_MATCH144                          Operational           112
PROTOCOL_MATCH                           Operational           104
PROTOCOL_MATCH144                        Operational           103
FRAG_MATCH                               Operational           109
PRECEDENCE_TOS_MATCH                     Operational           106
PRECEDENCE_TOS_MATCH144                  Operational           105

Related Commands

Command
Description

show pxf cpu statistics

Displays PXF CPU statistics.

show pxf statistics

Displays a chassis-wide summary of PXF statistics.


show pxf cpu atom

To display Parallel eXpress Forwarding (PXF) CPU Any Transport over MPLS (AToM) forwarding information for an interface or Virtually Cool Common Index (VCCI), use the show pxf cpu atom command in privileged EXEC mode.

show pxf cpu atom [interface-name | vcci]

Syntax Description

interface-name

(Optional) Name of the interface.

vcci

(Optional) VCCI entry identifier.


Command Modes

Privileged EXEC (#)

Command History

Release
Modification

12.2(31)SB

This command was introduced on the Cisco 10000 series router.


Examples

The following example shows AToM forwarding information for Gigabit Ethernet interface 6/0/0. The fields shown in the display are self-explanatory.

Router#: show pxf cpu atom gigabitethernet 6/0/0

 Imposition Information for VCCI 0x9E2:
    Output VCCI: 0x0
    Mac rewrite index: 0x0 extension: 0x0
    Ingress Flags: 0x0
    PTI Action Table: 0x0

Related Commands

Command
Description

show mpls l2transport vc

Displays information about AToM VCs that are enabled to route Layer 2 packets on a router.

show pxf cpu mpls

Displays PXF MPLS FIB entry information.

show pxf cpu subblocks

Displays subblocks information that includes column 0 of AToM.


show pxf cpu bba

To display information on Parallel eXpress Forwarding (PXF) CPU Broadband Aggregation (BBA) groups, use the show pxf cpu bba command in privileged EXEC mode.

show pxf cpu bba

Syntax Description

This command has no arguments or keywords.

Command Modes

Privileged EXEC (#)

Command History

Release
Modification

12.2S

This command was introduced.

12.2(31)SB2

This command was integrated into Cisco IOS Release 12.2(31)SB2.


Examples

The following example shows BBA groups information in the PXF CPU:

Router# show pxf cpu bba 

6w3d: show_pxf_bba
6w3d: %IPCOIR-4-REPEATMSG: IPC handle already exists for 1/0
6w3d: %IPCOIR-2-CARD_UP_DOWN: Card in slot 1/0 is down.  Notifying 4oc3atm-1 dr.
6w3d: %C10K_ALARM-6-INFO: ASSERT CRITICAL slot 1 Card Stopped Responding OIR Al 
6w3d: %IPCOIR-5-CARD_DETECTED: Card type 4oc3atm-1 (0x2D8) in slot 1/0
6w3d: %IPCOIR-5-CARD_LOADING: Loading card in slot 1/0 sw version 1.1 code MD5 C
6w3d: %C10K-5-LC_NOTICE: Slot[1/0] 4oc3atm-1 Image Downloaded...Booting...
6w3d: %IPCOIR-5-CARD_DETECTED: Card type 4oc3atm-1 (0x2D8) in slot 1/0
6w3d: %C10K_ALARM-6-INFO: CLEAR CRITICAL slot 1 Card Stopped Responding OIR Ala 
6w3d: %IPCOIR-2-CARD_UP_DOWN: Card in slot 1/0 is up.  Notifying 4oc3atm-1 driv.

Related Commands

Command
Description

bba-group pppoe

Configures a BBA group to establish PPPoE sessions.


show pxf cpu buffers

To display packet buffer memory for temporary packet storage in the Cisco Internetwork Performance Monitor (IPM) of the Parallel eXpress Forwarding (PXF), use the show pxf cpu buffers command in privileged EXEC mode.

show pxf cpu buffers

Syntax Description

This command has no arguments or keywords.

Command Modes

Privileged EXEC (#)

Command History

Release
Modification

12.2S

This command was introduced on the Cisco 10000 series router.

12.2(31)SB

This command was integrated into Cisco IOS Release 12.2(31)SB.


Usage Guidelines

This command provides information about the number of handles that are used and available. Handles are outstanding packets in the virtual time management system (VTMS).

Examples

The following example shows the number of handles that are used and available:

Router# show pxf cpu buffers

Cobalt2 ttc running.
Calculations could be off by (+/-) cache sizes.
         cache size
small    512
large    128

pool     # handles    available
--------------------------------
small      524288     523808
large       32768     32624 

Table 85 describes the fields shown in the display.

Table 85 show pxf cpu buffers Field Descriptions 

Field
Description

pool

Identifies the buffer pool.

# handles

The number of handles that are currently used.

available

The number of handles that are currently available.


Related Commands

Command
Description

clear pxf

Clears PXF counters and statistics.

show pxf statistics

Displays chassis-wide, summary PXF statistics.


show pxf cpu cef

The show pxf cpu cef command is replaced by the show ip cef platform command on the Cisco 10000 series router. See the show ip cef platform command for more information.

show pxf cpu context

To display the current and historical loads on the Parallel eXpress Forwarding (PXF), use the show pxf cpu context command in privileged EXEC mode.

show pxf cpu context

Syntax Description

This command has no arguments or keywords.

Command Modes

Privileged EXEC (#)

Command History

Release
Modification

12.2S

This command was introduced on the Cisco 10000 series router.

12.3(7)XI1

This command was integrated into Cisco IOS Release 12.3(7)XI1.

12.2(31)SB

This command was integrated into Cisco IOS Release 12.2(31)SB.


Examples

The show pxf cpu context command shows how busy the PXF forwarding process (FP) is with the current traffic load. The first section displays the number of contexts of each type that have entered the PXF engine since it was last reloaded. If counters are idle, the PXF pipeline is not operating properly.

Router# show pxf cpu context

FP context statistics    count          rate (since last time command was run)
---------------------    -------------  ----------
    feed_back            168635         0
    new_work_from_lc     7474477        13
    new_work_from_rp     964679         1
    new_work_from_replay 0              0
    null_context         3797097495884  6312156
                                        ----------
                                        6312170
FP average context/sec   1min        5min        60min
---------------------    ----------  ----------  ----------
    feed_back            0           0           0          cps
    new_work_from_lc     8           8           8          cps
    new_work             1           1           1          cps
    new_work_from_replay 0           0           0          cps
    null_context         6312260     6312261     6312250    cps
---------------------    ----------  ----------  ----------
    Total                6312270     6312271     6312260    cps

FP context utilization 1min        5min        60min
---------------------  ----------  ----------  ----------
    Actual             0   %       0   %       0   %
    Theoretical        0   %       0   %       0   %
    Maximum            98  %       98  %       98  %

Table 85 describes the significant fields shown in the display.

Table 86 show pxf cpu context Field Descriptions 

Field
Description

FP context statistics

feed_back

Packets requiring additional passes through the pipeline. This counter is incremented once for each additional pass.

new_work

New packets input to the PXF pipeline. This counter represents a snapshot of the amount of incoming traffic being processed by the processor.

null_context

An indication of unused forwarding bandwidth (idle time). This counter is incremented for every context during which the PXF pipeline is not processing traffic. This counter represents the processor's potential to handle additional traffic. As the processor becomes more busy, the value for null decreases until it becomes zero, at which point the processor has reached its maximum usage.

FP average context/sec

feed_back

Displays the rate, in terms of the number of contexts per second (cps) for the feed_back counter for the last 1-minute, 5-minute, and 60-minute time periods.

new_work

Displays the rate, in terms of the number of contexts per second (cps) for the new_work counter for the last 1-minute, 5-minute, and 60-minute time periods.

null_context

Displays the rate, in terms of the number of contexts per second (cps) for the null_counter for the last 1-minute, 5-minute, and 60-minute time periods.

FP context utilization

Actual

Displays the actual percentage of processor usage per second, compared to the theoretical maximum, for the last 1-minute, 5-minute, and 60-minute time periods.

Theoretical

Displays the percentage of processor usage compared to the ideal theoretical capacities for the last 1-minute, 5-minute, and 60-minute time periods. The theoretical maximum for the PXF processors is 3,125,000 contexts per second (cps).

Maximum

Displays the actual maximum percentage of processor usage that has occurred for the last 1-minute, 5-minute, and 60-minute time periods.


Related Commands

Command
Description

clear pxf

Clears PXF counters and statistics.

show pxf statistics

Displays chassis-wide, summary PXF statistics.


show pxf cpu feedback

To display the total number of feedbacks through the Parallel eXpress Forwarding (PXF) by all packets, use the show pxf cpu feedback command in privileged EXEC mode.

show pxf cpu feedback

Syntax Description

This command has no arguments or keywords.

Command Modes

Privileged EXEC (#)

Command History

Release
Modification

12.2S

This command was introduced on the Cisco 10000 series router.

12.2(31)SB

This command was integrated into Cisco IOS Release 12.2(31)SB.


Examples

The following example shows feedback counters information:

Router# show pxf cpu feedback

Load for five secs: 5%/0%; one minute: 6%; five minutes: 2%
Time source is hardware calendar, *21:13:02.615 UTC Tue Nov 29 2005

FP column 0 feedback counts

Global packet handle retry counter = 0

   Name                      Current                Difference (since last show)
   ---------------------     ----------             ----------
   bypass                  = 0                      0
   schedule retry          = 0                      0
   WRED sample             = 0                      0
   MLPPP linkq update      = 0                      0
   IP frag                 = 0                      0
   ICMP                    = 0                      0
   layer2 divert           = 0                      0
   tunnel lookup           = 0                      0
   tunnel RX               = 0                      0
   tunnel TX               = 0                      0
   output qos              = 0                      0
   tag not ip              = 0                      0
   netflow accumulate      = 0                      0
   netflow age             = 0                      0
   netflow swap            = 0                      0
   netflow export          = 0                      0
   PBR                     = 0                      0
   input secACL log        = 0                      0
   input secACL split      = 0                      0
   output secACL log       = 0                      0
   output secACL split     = 0                      0
   IPC response            = 0                      0
   IPC MLPPP flush         = 0                      0
   input qos split         = 0                      0
   output qos split        = 0                      0
   MLPPP fwd packet        = 0                      0
   MLPPP background        = 0                      0
   MLPPP flush             = 0                      0
   drop                    = 0                      0
   QPPB                    = 0                      0
   mcast lookup            = 0                      0
   mcast replicate         = 0                      0
   mcast rpf failed        = 0                      0
   mcast bypass            = 0                      0
   PBR split               = 0                      0
   MLPPP lock retry        = 0                      0
   output secACL           = 0                      0
   qos divert split        = 0                      0
   qos inject split        = 0                      0
   secACL divert split     = 0                      0
   MLPPP frag              = 0                      0
   mpls deaggregation      = 0                      0
   tunnel in secACL log    = 0                      0
   tunnel out secACL log   = 0                      0
   no packet handle        = 0                      0
   PBR to FIB              = 0                      0
   MLPPP flush lock retry  = 0                      0
   MLPPP flush setup       = 0                      0
   MLPPP sync flush req    = 0                      0
   tail drop IP frag       = 0                      0
   RP inject               = 0                      0
   feedback retry          = 0                      0
   MLPPP discard feedback  = 0                      0
   MLPPP stats copy IPC    = 0                      0
   IPM replay              = 0                      0
   IPM replay drop         = 0                      0
   IP reasm lock retry     = 0                      0
   IP reasm recover punt   = 0                      0
   IP reasm forward        = 0                      0
   IP reasm insertion      = 0                      0
   LAC switch              = 0                      0
   L2TP decap              = 0                      0
   IP reasm fb divert qos  = 0                      0
   keepalive               = 0                      0
   drop stats redirect     = 0                      0
   AToM multiplexed        = 0                      0
   LFI reassembly          = 0                      0
   LFI remove entry        = 0                      0
   iEdge translation       = 0                      0
   iEdge divert            = 0                      0
   multiple input qos      = 0                      0
   multiple output qos     = 0                      0
   iEdge PBHK DS trans     = 0                      0
   LAC switch qos          = 0                      0
   WRED sample init        = 0                      0
   replay egress           = 0                      0
   IPV6 FIB                = 0                      0
   ICMPV6                  = 0                      0
   IPV6 ACL                = 0                      0
   IPV6 DIVERT ACL         = 0                      0
   Total                   = 0                      0

Related Commands

Command
Description

show pxf cpu context

Displays the current and historical loads on the PXF.


show pxf cpu iedge

To display Parallel eXpress Forwarding (PXF) policy and template information, use the show pxf cpu iedge command in privileged EXEC mode.

show pxf cpu iedge [detail | policy policy-name | template]

Syntax Description

detail

(Optional) Displays detailed information about policies and templates.

policy policy-name

(Optional) Displays summary policy information.

template

(Optional) Displays summary template information.


Command Modes

Privileged EXEC (#)

Command History

Release
Modification

12.2S

This command was introduced.


Examples

The following example shows PXF template information. The fields shown in the display are self-explanatory.

Router# show pxf cpu iedge template 

Super ACL name                   OrigCRC   Class Count    CalcCRC
1sacl_2                         4EA94046   2             00000000
if_info 71BA3F20

Related Commands

Command
Description

show pxf statistics

Displays a summary of PXF statistics.


show pxf cpu ipv6

To display Parallel eXpress Forwarding (PXF) IPv6 statistics, use the show pxf cpu ipv6 command in privileged EXEC mode.

show pxf cpu ipv6 [ipv6: address [prefix] | acl-prefixes | hash | summary]

Cisco 10000 Series Router

show pxf cpu ipv6 [acl-prefixes | address | hash | summary | table | vrf]

Syntax Description

ipv6: address [prefix]

(Optional) Specifies the IPv6 address and optional IPv6 prefix for the information you want to display.

acl-prefixes

(Optional) Displays access control list (ACL) prefixes mapping information.

address

(Optional) Displays PXF IPv6 address-specific information.

hash

(Optional) Displays hash table summary information.

summary

(Optional) Displays a summary of the PXF IPv6 statistics.

table

(Optional) Displays detailed information about the PXF IPv6 forwarding table.

vrf

(Optional) Displays PXF IPv6 VRF information.


Command Modes

Privileged EXEC (#)

Command History

Release
Modification

12.2S

This command was introduced.

12.2(31)SB

This command was integrated in Cisco IOS Release 12.2(31)SB.

12.2(33)SB

This command was enhanced to provide the address, table, and vrf options, and implemented on the Cisco 10000 series router for the PRE3 and PRE4.


Usage Guidelines

Cisco 10000 Series Router

In Cisco IOS Release 12.2(33)SB, the show pxf cpu ipv6 table command displays the global table, but does not display the leafs that correspond to the IPv6 prefixes ::1/128 (Loopback) and ::/128 (All Zero). The microcode checks for these prefixes.

The show pxf cpu ipv6 table command replaces the show pxf cpu ipv6 command in Cisco IOS Release 12.2(31)SB.

Examples

The following example shows the PXF IPv6 statistics:

Router# show pxf cpu ipv6 

Mtrie Leaf Data: Prefix/Length

 Leaf prefix ::/0,ACL Index = 0
  Leaf elt_addr: 0x70D20001  SW_OBJ_FIB_ENTRY: 0x20A6E404 acl_index: 0
  Refcount: 514 Flags: 0x2  Parent: None
  First Covered: None
  Right Peer: None
========================================
0 routes in Mtrie with less specific overlapping parent route


Hash Table Leaf Data: Prefix/Length

 Leaf prefix ::1/128,ACL Index = 0
  Leaf elt_addr: 0x70D20011  SW_OBJ_FIB_ENTRY: 0x0 acl_index: 0
  128-bit Table Hash Value: 0xC7F7
  Refcount: 3 Flags: 0x2  Parent: None
  First Covered: None
  Right Peer: None
 Leaf prefix ::/128,ACL Index = 0
  Leaf elt_addr: 0x70D20009  SW_OBJ_FIB_ENTRY: 0x0 acl_index: 0
  128-bit Table Hash Value: 0xC2719
  Refcount: 3 Flags: 0x2  Parent: None
  First Covered: None
  Right Peer: None
========================================
0 routes in Hash Table with less specific overlapping parent route

Related Commands

Command
Description

show pxf cpu statistics

Displays PXF CPU statistics.


show pxf cpu mpls

To display Parallel eXpress Forwarding (PXF) Multiprotocol Label Switching (MPLS) Forwarding Information Base (FIB) information, use the show pxf cpu mpls command in privileged EXEC mode.

show pxf cpu mpls [labels label-value | vrf]

Syntax Description

labels label-value

(Optional) Displays the transport type and output features associated with the specified label value or label range. The label-value range is 0 to 524288.

vrf

(Optional) Displays virtual routing and forwarding (VRF) root information.


Command Modes

Privileged EXEC (#)

Command History

Release
Modification

12.2S

This command was introduced.


Examples

The following example shows VRF root information. The fields shown in the display are self-explanatory.

Router# show pxf cpu mpls vrf 

VRF_ID 0     FIB_ROOT(RP) 0x72400000

Related Commands

Command
Description

ping mpls

Checks MPLS LSP connectivity.

show mpls interfaces

Displays information about the interfaces configured for label switching.

show pxf cpu statistics

Displays PXF CPU statistics.

trace mpls

Discovers MPLS LSP routes that packets will take when traveling to their destinations.


show pxf cpu mroute

To display Parallel eXpress Forwarding (PXF) multicast route (mroute) information, use the show pxf cpu mroute command in privileged EXEC mode.

show pxf cpu mroute [ipaddress1] [ipaddress2]

Syntax Description

[ipaddress1] [ipaddress2]

(Optional) Displays PXF mroute information for a particular group or range of groups.


Command Modes

Privileged EXEC (#)

Command History

Release
Modification

12.2S

This command was introduced.


Examples

The following example shows PXF mroute information:

Router# show pxf cpu mroute

Shadow G/SG[5624]: s: 0.0.0.0 g: 224.0.1.40 uses: 0 bytes 0 flags: [D ] LNJ
Interface                  vcci  offset   rw_index mac_header

In :                       0     0x000004 

Shadow G/SG[3195]: s: 0.0.0.0 g: 234.5.6.7 uses: 0 bytes 0 flags: [5 ] NJ

Interface                  vcci  offset   rw_index mac_header

In :                       0     0x000008 

Out: Cable5/1/0            5     0x00002C 1B       00000026800001005E05060700010

Out: Cable6/1/1            9     0x000028 1A       00000026800001005E05060700010

Out: Cable6/0/0            6     0x000024 19       00000026800001005E05060700010

Out: Cable5/0/0            3     0x000020 18       00000026800001005E05060700010

Out: Cable7/0/0            A     0x00001C 17       00000026800001005E05060700010

Out: Cable7/1/1            C     0x000018 16       00000026800001005E05060700010

Out: Cable7/1/0            B     0x000014 15       00000026800001005E05060700010

Out: Cable6/1/0            8     0x000010 14       00000026800001005E05060700010

Out: Cable6/0/1            7     0x00000C 13       00000026800001005E05060700010

Out: Cable5/0/1            4     0x000008 12       00000026800001005E05060700010

Table 87 describes the fields shown in the display.

Table 87 show pxf cpu mroute Field Descriptions 

Field
Description

Interface

Interface or subinterface.

vcci

Virtually Cool Common Index (VCCI) for the interface or subinterface.

rw index

Index used to read and write into the multicast table for this entry.

mac_header

MAC header that is used when rewriting the packet for output.


Related Commands

Command
Description

show ip mroute

Displays the Cisco IOS version of a multicast routing table entry.

show pxf statistics

Displays chassis-wide, summary PXF statistics.


show pxf cpu pbr action

To display policy-based routing (PBR) actions configured in the Parallel eXpress Forwarding (PXF), use the show pxf cpu pbr action command in privileged EXEC mode.

show pxf cpu pbr action map-name

Cisco 10000 Series Router (PRE3)

show pxf cpu pbr [action map-name | tcam map-name | flex-sum]

Syntax Description

action map-name

(Optional) Displays PBR action information and redirects the command output to the route map you specify.

tcam map-name

(Optional) Displays VMR (value, plus a mask and result) information stored in ternary content addressable memory (TCAM) and redirects the command output to the route map you specify.

Note This option is only available on the PRE3 for the Cisco 10000 series router.

flex-sum

(Optional) Displays summary information describing the amount of memory allocated in the PXF engine for use by the flexible key construction microcode. This information is useful for design teams.

Note This option is only available on the PRE3 for the Cisco 10000 series router.


Command Modes

Privileged EXEC (#)

Command History

Release
Modification

12.2S

This command was introduced.

12.3(7)XI1

This command was introduced on the Cisco 10000 series router for the PRE2.

12.2(31)SB2

This command was introduced on the Cisco 10000 series router for the PRE3.


Usage Guidelines

This command is useful to determine if an adjacency has been found for a set ip next-hop ip-address route map configuration command.

Examples

The following example shows the PBR route maps configured in the PXF:

Router# show pxf cpu pbr action foo

Show PBR Action:
----------------------------------------------------------------------
Policy number: 1           
route-map foo, permit, sequence 10
  map number    = 0           
  action index  = 0           
    primary action   : SET_ROUTE
    secondary action : - none -
    mac-rewr index = 0x0000 0015
    vcci = 0x09D4, qos group = 0, tos prec = 0
    tt_pkt_count = 0            tt_byte_count = 0           
 Adjacency data 0x20D29968
 XCM adjacency from 0x70000120(RP) 
   0xA0000120(FP) index 0x24:

Cisco 10000 Series Router (PRE3)

The following configuration example shows a PBR configuration in which traffic classification is based on the IP access list named pbr_length. The route map permits traffic based on the specified matching criteria and sets the next hop address of each packet.

ip access-list extended pbr_length
    permit tcp any any
!
route-map pbr_length permit 10
    match ip address pbr_length
    match length 100 200
    set ip next-hop 2.0.95.5                    !
route-map pbr_length permit 20
    match ip address pbr_length
    match length 200 300
    set ip next-hop 2.0.95.5                    !
route-map pbr_length permit 30
    match length 300 400
    set ip next-hop 2.0.95.5                    !

The following sample output from the show pxf cpu pbr command shows the type of information that displays based on the above PBR configuration:

Router# show pxf cpu pbr action pbr_length

Show PBR Action:

----------------------------------------------------------------------
Policy number: 3           

route-map pbr_length, permit, sequence 10
  map number    = 0           
  action index  = 64          
  map vcci out  = 0x0
  tt_pkt_count  = 0            tt_byte_count = 0           

    primary action   : NULL_ACTION
    secondary action : - none -
    mac-rewr index = 0x0000 0000
    vcci = 0x0000, qos group = 0, tos prec = 0

......................................................................

route-map pbr_length, permit, sequence 20
  map number    = 1           
  action index  = 65          
  map vcci out  = 0x0
  tt_pkt_count  = 0            tt_byte_count = 0           
          
    primary action   : NULL_ACTION
    secondary action : - none -
    mac-rewr index = 0x0000 0000
    vcci = 0x0000, qos group = 0, tos prec = 0

......................................................................

route-map pbr_length, permit, sequence 30
  map number    = 2           
  action index  = 66          
  map vcci out  = 0x0
  tt_pkt_count  = 0            tt_byte_count = 0           

    primary action   : NULL_ACTION
    secondary action : - none -
    mac-rewr index = 0x0000 0000
    vcci = 0x0000, qos group = 0, tos prec = 0

The following sample output from the show pxf cpu pbr tcam command shows the type of detailed VMR (value, plus a mask and result) information that displays:

Router# show pxf cpu pbr tcam pbr_length detail 

VMR data for Route-map pbr_length

-------------------------------------------------------------
VMR Format - handle: 5050BC90
Format has 5 fields, refcount = 1
Field: Format, FIXED, start_bit = 69, end_bit = 71
Field: ACL index, FIXED, start_bit = 54, end_bit = 68
Field: Flags, FIXED, start_bit = 43, end_bit = 53
Field: L4 proto, FIXED CNV, start_bit = 16, end_bit = 23
Field: Unknown, FLEX, start_bit = 0, end_bit = 15 Total bits = 53, format = 72 GMR used: 0 
Col 3 LKBP Vector: 96C
Status: Running

-------------------------------------------------------------
VMRs
------ VMR 0 ------
V: 7000C000 00000600 70
M: FFFFD800 0000FFFF F0
R: 80000104
Format: 00000003/00000007
ACL index: 00004003/00007FFF
L4 proto: 00000006/000000FF
Flags: 00000000/00000300
Packet Length: 00000070/0000FFF0
------ VMR 1 ------
V: 7000C000 00000600 68
M: FFFFD800 0000FFFF F8
R: 80000104
Format: 00000003/00000007
ACL index: 00004003/00007FFF
L4 proto: 00000006/000000FF
Flags: 00000000/00000300
Packet Length: 00000068/0000FFF8
------ VMR 2 ------
V: 7000C000 00000600 64
M: FFFFD800 0000FFFF FC
R: 80000104
Format: 00000003/00000007
ACL index: 00004003/00007FFF
L4 proto: 00000006/000000FF
Flags: 00000000/00000300
Packet Length: 00000064/0000FFFC
.
.
.
------ VMR 18 ------
V: 7000C000 00000000 00
M: FFFFC000 00000000 00
R: 80000110
Format: 00000003/00000007
ACL index: 00004003/00007FFF
L4 proto: 00000000/00000000
Flags: 00000000/00000000
Packet Length: 00000000/00000000

Related Commands

Command
Description

show pxf cpu policy-data

Displays QoS policy data index usage statistics.

show pxf cpu vcci

Displays VCCI to interface mapping information.


show pxf cpu police

To display all active policer policies in the Parallel eXpress Forwarding (PXF), including active interface and policing parameters, use the show pxf cpu police command in privileged EXEC mode.

show pxf cpu police [policy-map-name]

Syntax Description

policy-map-name

(Optional) Policy for which you want to display PXF policing statistics.


Command Modes

Privileged EXEC (#)

Command History

Release
Modification

12.2S

This command was introduced.

12.3(7)XI1

This command was integrated into Cisco IOS Release 12.3(7)XI1.


Usage Guidelines

If a policy name is not specified, the command displays policing statistics for all policy maps.

Examples

The following example shows the PXF policing statistics for a policy called policetest. The fields shown in the display are self-explanatory.

Router# show pxf cpu police policetest

Policy policetest:
   Class: police_class
  Interface VCCI 0x9DD Output Policy:
     police 8000 8000 15000 conform-action transmit exceed-action drop violate-action drop

   Class: class-default
      *** No police action ***

Related Commands

Command
Description

show pxf cpu vcci

Displays VCCI to interface mapping information.

show pxf statistics

Displays chassis-wide, summary PXF statistics.


show pxf cpu policy-data

To display Parallel eXpress Forwarding (PXF) policy data index usage statistics, use the show pxf cpu policy-data command in privileged EXEC mode.

show pxf cpu policy-data

Syntax Description

This command has no arguments or keywords.

Command Modes

Privileged EXEC (#)

Command History

Release
Modification

12.2S

This command was introduced.

12.3(7)XI1

This command was integrated into Cisco IOS Release 12.3(7)XI1.


Examples

The following example shows PXF policy data which is information related to the number of classes in a policy and the reservation of unique indexes to support match statistics and token buckets. Policy data index statistics are related to free match statistics indexes. Exhaustion of these indexes means no more policies can be created in the router. Secondary policy data indexes are related to free token bucket indexes. The fields shown in the display are self-explanatory.

Router# show pxf cpu policy-data

Service policy data index usage statistics:
Total groups = 9, pool_defragmented = TRUE.
     Group size     Chunk count
     1              0         
     2              1         
     4              1         
     8              0         
     16             1         
     32             1         
     64             1         
     128            1         
     256            1023      
Total free count  = 262134.
Total chunk count = 262144.

Secondary policy data index usage statistics:
Total groups = 9, pool_defragmented = TRUE.
     Group size     Chunk count
     2              1         
     4              1         
     8              0         
     16             1         
     32             1         
     64             1         
     128            1         
     256            1         
     512            2047      
Total free count  = 1048566.
Total chunk count = 1048576.

The Group size field is the number of policy classes. The Chunk count field is the number of blocks the group holds.

Related Commands

Command
Description

show pxf cpu pbr action

Displays PBR actions configured in the PXF for all PBR route maps.

show pxf cpu vcci

Displays VCCI to interface mapping information.


show pxf cpu qos

To display Parallel eXpress Forwarding (PXF) External Column Memory (XCM) contents related to a particular policy, use the show pxf cpu qos command in privileged EXEC mode.

show pxf cpu qos [policy-map policy-name | vcci-maps]

Cisco 10000 Series Router

show pxf cpu qos [vcci | classifiers | flex-sum | policy-map policy-name | vcci-maps]

Syntax Description

vcci

(Optional) Virtual Channel Circuit Identifier (VCCI). Information about this specified VCCI will be displayed.

classifiers

(Optional) Displays information about the criteria used to classify traffic.

flex-sum

(Optional) Displays summary information describing the amount of memory allocated in the PXF engine for use by the flexible key construction microcode.

Note This option is only available on the Cisco 10000 series router for the PRE3.

policy-map policy-name

(Optional) Displays per-policy map information.

vcci-maps

(Optional) Displays VCCI map values.


Command Modes

Privileged EXEC (#)

Command History

Release
Modification

12.2S

This command was introduced.

12.3(7)XI1

This command was introduced on the Cisco 10000 series router for the PRE2.

12.2(28)SB

This command was integrated into Cisco IOS Release 12.2(28)SB.

12.2(31)SB2

This command was introduced on the PRE3 for the Cisco 10000 series router.


Usage Guidelines

This command is useful in verifying the presence of a policy on interfaces and indexes programmed in the PXF.

Examples

The following example shows XCM contents related to a policy called police_test, which is defined as follows:

policy-map police_test
 class high-priority
 priority
 class low-priority
  set atm-clp
 class class-default
    queue-limit 512

Router# show pxf cpu qos police_test

Output Policymap: police_test
 Vcci: A05  Flags: 4  Policymap_index: 6  Policymap_data_index: 12
 OUT AT1/0/0.111 (0x71764660) ref_count 1
Output Action Table Contents for vcci 0xA05 - Policymap index: 6
 class-name: high-priority  class_index: 0  action_flags: 0x00
  srp_class_id: 0x01  prec/dscp: 0x00  cos: 0
  discard_class: 0x00  exp_value: 0
class-name: low-priority  class_index: 1  action_flags: 0x10
  srp_class_id: 0x00  prec/dscp: 0x00  cos: 0
  discard_class: 0x00  exp_value: 0
class-name: class-default  class_index: 2  action_flags: 0x00
  srp_class_id: 0x00  prec/dscp: 0x00  cos: 0
  discard_class: 0x00  exp_value: 0

Related Commands

Command
Description

show pxf cpu statistics qos

Displays match statistics for a service policy on an interface.


show pxf cpu queue

To display parallel express forwarding (PXF) queueing and link queue statistics, use the show pxf cpu queue command in privileged EXEC mode.

show pxf cpu queue [interface | QID | summary]

Cisco uBR10012 Universal Broadband Router

show pxf cpu queue [interface | QID]

Syntax Description

interface

(Optional) The interface for which you want to display PXF queueing statistics. This displays PXF queueing statistics for the main interface and all subinterfaces and permanent virtual circuits (PVCs). It also displays packets intentionally dropped due to queue lengths.

QID

(Optional) The queue identifier.

summary

(Optional) Displays queue scaling information such as:

Number of queues and recycled queues.

Number of available queue IDs (QIDs).

Number of packet buffers, recycled packet buffers, and free packet buffers.


Command Modes

Privileged EXEC (#)

Command History

Release
Modification

12.2S

This command was introduced.

12.2(28)SB

This command was integrated into Cisco IOS Release 12.2(28)SB.

12.3(7)XI1

This command was integrated into Cisco IOS Release 12.3(7)XI1.

12.3(23)BC1

The "Link Queues" output field for dynamic bandwidth sharing-enabled modular cable and wideband cable interfaces was added on the Cisco uBR10012 universal broadband router.

12.2(33)SB

This command was modified for virtual access interfaces (VAIs) and the output was modified for the summary option, and implemented on the Cisco 10000 series router for the PRE3 and PRE4.

12.2(33)SCB

The output of this command has been updated or re-arranged (compared to the VTMS version) for DOCSIS Weighted Fair Queuing (WFQ) Scheduler feature and implemented on the Cisco uBR10012 router.


Usage Guidelines

When neither the interface or QID is specified, the command displays queuing statistics for the route processors (RPs).

Cisco 10000 Series Router

The Cisco 10000 series router high-speed interfaces work efficiently to spread traffic flows equally over the queues. However, using single traffic streams in a laboratory environment might result in less-than-expected performance. To ensure accurate test results, test the throughput of the Gigabit Ethernet, OC-48 POS, or ATM uplink with multiple source or destination addresses. To determine if traffic is being properly distributed, use the show pxf cpu queue command.

In Cisco IOS Release 12.2(33)SB and later releases, the router no longer allows you to specify a virtual access interface (VAI) as viX.Y in the show pxf cpu queue command. Instead, you must spell out the VAI as virtual-access.

For example, the router accepts the following command:

Router# show pxf cpu queue virtual-access2.1

In releases prior to Cisco IOS Release 12.2(33)SB, the router accepts the abbreviated form of the VAI. For example, the router accepts the following command:

Router# show pxf cpu queue vi2.1

In Cisco IOS Release 12.2(33)SB and later releases, the output from the show pxf cpu queue interface summary command displays only the physical interface and the number of logical links. The output does not display the number of priority queues, class queues, and so on. This modification applies to the PRE3 and PRE4.

Cisco uBR10012 Universal Broadband Router

If dynamic bandwidth sharing (DBS) is enabled, the link queue information that is displayed refers to the specific type of interface that is configured—modular cable or wideband cable. The summary keyword option is not supported for the Cisco uBR10012 universal broadbandrRouter for wideband cable or modular cable interfaces. The ATM interface output is not available for this router.

See Table 88 for descriptions of the interface keyword fields.

Table 88 show pxf cpu queue Interface Option Field Descriptions 

Field
Description

<0-131071>

QID (queue identifier)

ATM

Asynchronous transfer mode interface

Note The ATM interface output is not available for the Cicso uBR10012 universal broadband router.

BVI

Bridge-group virtual interface

Bundle

Cable virtual bundle interface

CTunnel

CTunnel interface

Cable

Cable modem termination service (CMTS) interface

DTI

Digital trunk interface

Dialer

Dialer interface

Ethernet

IEEE 802.3

FastEthernet

FastEthernet IEEE 802.3

GigabitEthernet

GigabitEthernet IEEE 802.3z

Group-Async

Async group interface

Loopback

Loopback interface

MFR

Multilink frame relay bundle interface

Modular-Cable

Modular cable interface

Multilink

Multilink group interface

Null

Null interface

Port-channel

Ethernet channel of interfaces

RP

Forwarding path (FP) to route processing (RP) queues

Tunnel

Tunnel interface

Vif

Pragmatic general multicast (PGM) host interface

Virtual-Template

Virtual template interface

Virtual-TokenRing

Virtual token ring

WB-SPA

line card to line card (LC-LC) queues

Wideband-Cable

Wideband CMTS interface


Examples

The following example shows PXF queueing statistics for an ATM interface when a QID is not specified. The sample output includes the dropped and dequeued packets for the VCs, and for classes associated with sessions that inherit queues from VCs.

Router# show pxf cpu queue atm 5/0/2

VCCI 2517: ATM non-aggregated VC 1/229, VCD 1, Handle 1, Rate 500 kbps

      VCCI/ClassID  ClassName      QID   Length/Max  Res  Dequeues  Drops
      0 2517/0      class-default  269   0/4096       11         3      0
      0 2517/31     pak-priority   268   0/32         11         4      0

   Queues Owned but Unused by VC (inheritable by sessions)

      ClassID       ClassName      QID   Length/Max  Res  Dequeues  Drops
            0       class-default  275   0/32         11       100      0
           31       pak-priority   268   0/32         11         4      0


VCCI 2517: ATM non-aggregated VC 1/233, VCD 4, Handle 4, Rate 50 kbps

      VCCI/ClassID  ClassName      QID   Length/Max  Res  Dequeues  Drops
      0 2517/0      class-default  269   0/4096       11         3      0
      0 2517/31     pak-priority   268   0/32         11         4      0

   Queues Owned but Unused by VC (inheritable by sessions)

      ClassID      ClassName       QID   Length/Max  Res  Dequeues  Drops
            0      class-default   274   0/32         11         0      0
           31      pak-priority    268   0/32         11         4      0


VCCI 2520: ATM non-aggregated VC 1/232, VCD 3, Handle 3, Rate 500 kbps

      VCCI/ClassID  ClassName       QID   Length/Max  Res  Dequeues  Drops
      0 2520/0      class-default   273   0/32         11         0      0
      0 2520/31     pak-priority    268   0/32         11         4      0


VCCI 2519: ATM non-aggregated VC 1/231, VCD 2, Handle 2, Rate 500 kbps

      VCCI/ClassID  ClassName       QID   Length/Max  Res  Dequeues  Drops
      0 2519/0      class-default   272   0/32         11         0      0
      0 2519/31     pak-priority    268   0/32         11         4      0

The following example displays PXF queuing statistics for QID 267:

Router# show pxf cpu queue 267

ID                                          : 267
Priority                                    : Lo
CIR (in-use/configured)                     : 0/65535
EIR (in-use/configured)                     : 0/0
MIR (in-use/configured)                     : 0/65535
Maximum Utilization configured              : no
Link                                        : 2
Flowbit (period/offset)                     : 32768/32768
Burst Size                                  : 1024 bytes
Bandwidth                                   : 133920 Kbps
Channel                                     : 0
Packet Descriptor Base                      : 0x00000100
ML Index                                    : 0
Length/Average/Alloc                        : 0/0/32
Enqueues (packets/octets)                   : 293352/9280610
Dequeues (packets/octets)                   : 293352/9280610
Drops (tail/random/max_threshold)           : 0/0/0
Drops (no_pkt_handle/buffer_low)            : 0/0
WRED (weight/avg_smaller)                   : 0/0
WRED (next qid/drop factor)                 : 0/0
WRED (min_threshold/max_threshold/scale/slope):
precedence 0                               : 0/0/0/0
precedence 1                               : 0/0/0/0
precedence 2                               : 0/0/0/0
precedence 3                               : 0/0/0/0
precedence 4                               : 0/0/0/0
precedence 5                               : 0/0/0/0
precedence 6                               : 0/0/0/0
precedence 7                               : 0/0/0/0

Cisco uBR10012 Universal Broadband Router

The following examples show link queue information for specific wideband cable and modular cable interfaces when dynamic bandwidth sharing is enabled.

Modular Cable Interface

Router(config)# interface modular-cable 1/0/0:1
.
.
.

Router(config-if)# cable dynamic-bw-sharing
.
.
.

Router# show pxf cpu queue modular-cable 1/0/0:1

Link Queues :
 QID   CIR(act/conf)       EIR            MIR       RF Chan.   Status
  420   19661/19661        1/1        65535/65535      0       Inactive

Wideband Cable Interface

Router(config)# interface wideband-cable 1/0/0:0
.
.
.
Router(config-if)# cable dynamic-bw-sharing
.
.
.
Router# show pxf cpu queue wideband-cable 1/0/0:0

Link Queues :
 QID   CIR(act/conf)       EIR            MIR       RF Chan.   Status
  419   32768/32768        1/1        65535/65535      0       Inactive
  566   19661/19661        1/1        65535/65535      1       Inactive

The following example shows service flow queue information for modular cable interfaces.

Router# show pxf cpu queue modular-cable 1/2/0:0

Cable Interface Queues:

QID     Len/Max  Dequeues   TailDrops   MinRt  Wt/Quantum  ShapeRt FlowId
                                        (Kbps)             (Kbps)
131147    0/255  190        0           0         1/240    0       58 
131148    0/255  33820      0           0         1/10000  0       32824 

Cable Service Flow Queues:

* Best Effort Queues

QID     Len/Max  Dequeues   TailDrops   MinRt  Wt/Quantum  ShapeRt FlowId
                                        (Kbps)             (Kbps)
131241    0/255  0          0           0         1/240    0       32881 

* CIR Queues

QID     Len/Max  Dequeues   TailDrops   MinRt  Wt/Quantum  ShapeRt FlowId
                                        (Kbps)             (Kbps)
2049    254/255  131018     485751      99        1/1920   0       32880 

* Low Latency Queues

QID     Len/Max  Dequeues   TailDrops 

Related Commands

Command
Description

cable dynamic-bw-sharing

Enables DBS on a specific modular cable or wideband cable interface.

show pxf cable controller

Displays information about the RF channel VTMS links and link queues.

show pxf cpu statistics queue

Displays PXF CPU queueing counters for all interfaces.


show pxf cpu reasm_index

To display information about reassembly of IP fragmented packets in the Parallel eXpress Forwarding (PXF), use the show pxf cpu reasm_index command in privileged EXEC mode.

show pxf cpu reasm_index [summary]

Syntax Description

summary

(Optional) Displays summary reassembly information of IP fragmented packets in the PXF.


Command Modes

Privileged EXEC (#)

Command History

Release
Modification

12.2S

This command was introduced.


Examples

The following example shows reassembly summary information. The fields shown in the display are self-explanatory.

Router# show pxf cpu reasm_index summary

Multilink Reassembly Index usage summary

      Maximum  Used     Available
      1251     0        1251

Related Commands

Command
Description

ip virtual-reassembly

Enables VFR information on an interface.

show ip virtual-reassembly

Displays VFR configuration and statistical information.


show pxf cpu statistics

To display Parallel eXpress Forwarding (PXF) CPU statistics, use the show pxf cpu statistics command in privileged EXEC mode.

show pxf cpu statistics [atom | backwalk | clear | diversion | drop [interface | vcci] | ip | ipv6 | l2tp | mlp | qos [interface] | queue | rx [vcci] | security | arp-filter | drl [ cable-wan-ip | wan-non-ip ]]

Cisco 10000 Series Router

show pxf cpu statistics diversion [ pxf [interface {interface | vcci}] | top number]

Syntax Description

atom

(Optional) Displays Any Transport over MPLS (AToM) statistics.

backwalk

(Optional) Displays backwalk requests statistics.

clear

(Optional) Clears PXF CPU statistics.

diversion

(Optional) Displays packets that the PXF diverted to the Route Processor (RP) for special handling.

drop [interface] [vcci]

(Optional) Displays packets dropped by the PXF for a particular interface or Virtual Circuit Connection Identifier (VCCI).

ip

(Optional) Displays IP statistics.

ipv6

(Optional) Displays IPv6 statistics.

l2tp

(Optional) Displays packet statistics for an L2TP Access Concentrator (LAC) (Optional) and L2TP Network Server (LNS).

mlp

(Optional) Displays multilink PPP (MLP) statistics.

pxf

(Optional) Displays packets that the PXF diverted to the Route Processor (RP). Available on the Cisco 10000 series router only.

pxf interface interface

(Optional) Displays per-interface PXF statistical information for the divert cause policer on a particular interface. Available on the Cisco 10000 series router only.

pxf interface vcci

(Optional) Displays per-VCCI PXF statistical information for the divert cause policer on a particular Virtual Circuit Connection Identifier (VCCI). Available on the Cisco 10000 series router only.

qos [interface]

(Optional) Displays match statistics for a service policy on an interface.

queue

(Optional) Displays queueing counters for all interfaces.

rx [vcci]

(Optional) Displays receive statistics for a VCCI.

security

(Optional) Displays ACL matching statistics.

top number

(Optional) Displays PXF statistical information for the number of top punters you specify. Available on the Cisco 10000 series router only. Valid values are from 1 to 100.

arp-filter

(Optional) Displays the ARP filter statistics.

drl

(Optional) Displays the divert rate limit.

cable-wan-ip

(Optional) Displays cable / wan-ip statistics for dropped packets.

wan-non-ip

(Optional) Displays DRL wan-non-ip statistics for dropped packets.


Command Modes

Privileged EXEC (#)

Command History

Release
Modification

12.3(7)XI1

This command was integrated into Cisco IOS Release 12.3(7)XI1.

12.2(28)SB

This command was introduced on the Cisco 10000 series router and integrated into Cisco IOS Release 12.2(28)SB.

12.2(31)SB

This command was integrated into Cisco IOS Release 12.2(31)SB.

12.2(33)SB

This command was enhanced to display per-interface or per-VCCI PXF statistical information for the divert cause policer on a particular interface or VCCI, to display the top punters on an interface, and to display the provisioned burst size for any divert causes. These enhancements were implemented on the Cisco 10000 series router for the PRE2, PRE3, and PRE4.

12.2(33)SCB

This command was integrated into Cisco IOS Release 12.2(33)SCB on the Cisco uBR7246VXR and Cisco uBR10012 universal broadband routers. Support for the Cisco uBR7225VXR router was added. The arp-filter, drl, cable-wan-ip, and wan-non-ip keywords were added .

12.2(33)SCE

This command was modified in Cisco IOS Release 12.2(33)SCE. The cable-wan-ip keyword was removed.


Usage Guidelines

Cisco 10000 Series Router Usage Guidelines

The show pxf cpu statistics diversion command displays statistical information about diverted packets. Divert causes with the string "ipv6..." display as "v6..." in the output of all show pxf cpu statistics diversion commands

The output from the show pxf cpu statistics diversion pxf command was enhanced in Cisco IOS Release 12.2(33)SB to display the provisioned burst size for any divert causes.

The show pxf cpu statistics diversion pxf interface interface command displays statistical information about the divert cause policer on a specific interface. The output of this command is similar to the output displayed at the aggregated level. This command enables you to see the traffic types being punted from an inbound interface, subinterface, and session.

The show pxf cpu statistics diversion pxf interface vcci command displays statistical information about the divert cause policer on a specific VCCI. The output of this command is similar to the output displayed at the aggregated level. This command enables you to see the traffic types being punted from an inbound interface, subinterface, and session.

The show pxf cpu statistics diversion top number command displays the interfaces, subinterfaces, and sessions with the highest number of punter packets.

Examples

The following example shows PXF queueing counters information. These are aggregate counters for all interfaces. The Total column is the total for all columns.


Note If you are troubleshooting link utilization issues, the deq_vtp_req, deq_flow_off, and deq_ocq_off counters may indicate what is causing the versatile time management scheduler (VTMS) to slow down.

If you are troubleshooting overall PXF throughput issues, look at the High Next Time, Low Next Time, High Wheel Slot, and Low Wheel Slot counters.


Router# show pxf cpu statistics queue

Column 6 Enqueue/Dequeue Counters by Rows:

dbg Counters         0          1          2          3          4          5          6          7      
Total
=============   ========== ========== ========== ========== ========== ========== ========== ========== 
==========
enq_pkt         0x0000FD9B 0x0000FC77 0x0000FE4A 0x0000FF81 0x0000FC53 0x0000FD2E 0x0000FF19 0x0000FDDE 
0x0007EE55
tail_drop_pkt   0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 
0x00000000
deq_pkt         0x0000FD47 0x0000FEF2 0x0000FCB3 0x0000FF65 0x0000FCE7 0x0000FC45 0x0000FEE7 0x0000FDF1 
0x0007EE55
deq_vtp_req     0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 
0x00000000
deq_flow_off    0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 
0x00000000
deq_ocq_off     0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 
0x00000000
enqdeq_conflict 0x0000003A 0x00000043 0x0000004A 0x00000039 0x0000003A 0x0000004F 0x00000036 0x00000031 
0x000001F0
bndl_pkt        0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 
0x00000000
frag_pkt        0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 
0x00000000
dbg_frag_drop   0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 
0x00000000
dbg_bndl_sem    0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 
0x00000000
context_inhibit 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 
0x00000000
bfifo_enq_fail  0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 
0x00000000
dbg1            0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 
0x00000000
dbg2            0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 
0x00000000
dbg3            0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 
0x00000000
dbg4            0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 
0x00000000
dbg5            0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 
0x00000000
dbg6            0x0000     0x0000     0x0000     0x0000     0x0000     0x0000     0x0000     0x0000     
0x0000
dbg7            0x00       0x00       0x00       0x00       0x00       0x00       0x00       0x00       0x00


Column 7 Rescheduling State Counters by Rows:

dbg Counters         0          1          2          3          4          5          6          7      
Total
=============   ========== ========== ========== ========== ========== ========== ========== ========== 
==========
High Next Time  0x524E1100 0x524E1140 0x524E1140 0x524E1180 0x524E11C0 0x524E11C0 0x524E1200 0x524E1240     -
Low Next Time   0x524E1100 0x524E1140 0x524E1140 0x524E1180 0x524E11C0 0x524E1200 0x524E1200 0x524E1240     -
High Wheel Slot 0x00000844 0x00000845 0x00000846 0x00000846 0x00000847 0x00000848 0x00000848 0x00000849     -
Low Wheel Slot  0x00000844 0x00000845 0x00000846 0x00000846 0x00000847 0x00000848 0x00000848 0x00000849     -
DEQ_WHEEL       0x0001F5D0 0x0001F4BD 0x0001F56B 0x0001F6BF 0x0001F396 0x0001F3E8 0x0001F6BF 0x0001F4A7 
0x000FA99B
DQ-lock Fails   0x0000039F 0x000003FD 0x000003B2 0x000003E1 0x000003CB 0x000003E2 0x000003FD 0x000003CD 
0x00001EA6
TW ENQ Fails    0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 
0x00000000
Q_SCHED         0x0000FACD 0x0000FC6B 0x0000FA38 0x0000FCE4 0x0000FA66 0x0000F994 0x0000FC62 0x0000FB8B 
0x0007DA3B
FAST_SCHED      0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 
0x00000000
Q_DEACT         0x0000FB03 0x0000F852 0x0000FB33 0x0000F9DB 0x0000F930 0x0000FA54 0x0000FA5D 0x0000F91C 
0x0007CF60
Q_ACTIVATE      0x0000F9B6 0x0000F8D4 0x0000FA6C 0x0000FBA9 0x0000F87E 0x0000F95B 0x0000FB0A 0x0000F9DE 
0x0007CF60
Q_CHANGE        0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 
0x00000000
DEBUG1          0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 
0x00000000
DEBUG2          0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 
0x00000000
DEBUG3          0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 
0x00000000
DEBUG4          0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 
0x00000000
DEBUG5          0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000 
0x00000000

Table 89 describes the significant fields shown in the display.

Table 89 show pxf cpu statistics queue Field Descriptions 

Field
Description

Column 6 Enqueue/Dequeue Counters by Rows:

enq_pkt

Packets the PXF enqueued.

tail_drop_pkt

Packets the PXF tails dropped.

deq_pkt

Packets the PXF dequeued.

deq_vtp_req

Number of times a dequeue was inhibited due to the virtual traffic policer.

deq_flow_off

Numbers of times a dequeue was inhibited due to a flowoff from the line card.

deq_ocq_off

Number of times a dequeue was inhibited due to link level flow control.

enqdeq_conflict

Shows a dequeue failed due to an enqueue to the same queue in progress.

bndl_pkt

Count of packets that were fragmented.

frag_pkt

Count of fragments sent.

dbg_frag_drop

Count of invalid multilink PPP (MLP) fragment handles.

dbg_bndl_sem

Count of semaphone collision (used for MLP).

context_inhibit

Number of times multilink transmit fragment processing was inhibited due to a lack of DMA resources.

bfifo_enq_fail

Count of bundle FIFO (BFIFO) enqueue failures.

Column 7 Rescheduling State Counters by Rows:

High Next Time

Current next send time for the high priority wheel.

Low Next Time

Current next send time for the low priority wheel.

High Wheel Slot

Current high priority slot number.

Low Wheel Slot

Current low priority slot number.

DEQ_WHEEL

Count of successful dequeues from the timing wheel.

DQ-lock Fails

Count of timing wheel dequeue failures (both queue empty and race conditions).

TW ENG Fails

Timing wheel enqueue failures.

Q_SCHED

Count of queues scheduled/rescheduled onto the timing wheel.

FAST_SCHED

Count of queues fast scheduled/rescheduled onto the timing wheel.

Q_DEACT

Count of queue deactivations.

Q_ACTIVATE

Count of queue activations (activate state).

Q_CHANGE

Count of queue changes; for example, Route Processor (RP) inspired rates changes.


The following example displays PXF L2TP packet statistics.


Note For L2TP Access Concentrator (LAC) operation, all statistics are applicable. For L2TP Network Server (LNS) operation, only the PPP Control Packets, PPP Data Packets, and PPP Station Packets statistics are meaningful.


Router# show pxf cpu statistics l2tp

LAC Switching Global Debug Statistics:
    PPP Packets           51648
    PPP Control Packets   51647
    PPP Data Packets      1
    Not IPv4 Packets      1
    IP Short Hdr Packets  1
    IP Valid Packets      0
    IP Invalid Packets    1
    DF Cleared Packets    0
    Path MTU Packets      0
    No Path MTU Packets   0
    Within PMTU Packets   0
    Fraggable Packets     0
    PMTU Pass Packets     0
    PMTU Fail Packets     0
    Encapped Packets      51648

L2TP Classification Global Debug Statistics:
    LAC or Multihop Packets  151341
    Multihop Packets         0
    PPP Control Packets      51650
    PPP Data Packets         99691
    PPP Station Packets      151341

The following example displays match statistics for the police_test policy on an ATM interface. The Classmap Index differentiates classes within a policy while the Match Number differentiates match statements within a class.

Router# show pxf cpu statistics qos atm 6/0/0.81801

               Classmap          Match         Pkts          Bytes     
                Index            Number      Matched        Matched   
             ------------      -----------  ------------   ----------
 police_test (Output) service-policy : 
         police_class    (0)       0            0             0       
                                   1            0             0       
                                   2            0             0       
                                   3            0             0       

         class-default   (1)       0            0             0       

Cisco 10000 Series Router

The following example displays the top 10 packet types diverted to the RP. The output displays the top punters by interface and by Layer 2 packet flow.

Router# show pxf cpu statistics diversion top 10

Top 10 punters by interface are:
Rate (pps)      Packets  (diverted/dropped)      vcci      Interface
        1       10/0     2606	Virtual-Access2.1
        Last diverted packet type is none.

Top 10 punters by Layer 2 flow are:
Rate (pps)      Packets  (diverted/dropped)     Interface       Layer 2 info
        1       15/0    ATM2/0/3       vpi 128/vci 4096/vcci 2591
        Last diverted packet type is oam_f4.
        1       15/0    ATM2/0/3       vpi 128/vci 4096/vcci 2593
        Last diverted packet type is oam_f4.

Related Commands

Command
Description

platform c10k divert- policer

Configures the rate and burst size of the divert-policer.

show pxf statistics

Displays a summary of statistics in the PXF.


show pxf cpu subblocks

To display Parallel eXpress Forwarding (PXF) CPU statistics for a bridged subinterface (encapsulation type), use the show pxf cpu subblocks command in privileged EXEC mode.

show pxf cpu subblocks interface-name

Syntax Description

interface-name

Name of the interface.


Command Modes

Privileged EXEC (#)

Command History

Release
Modification

12.2(28)SB

This command was introduced on the Cisco 10000 series router.

12.3(14)T

This command was enhanced to display more information for all subblocks.

12.2(31)SB

This command was integrated into Cisco IOS Release 12.2(31)SB.


Examples

The following example shows subblocks information for Gigabit Ethernet interface 7/0/0:

Router# show pxf cpu subblocks g7/0/0

GigabitEthernet7/0/0 is up
  ICB = 1C000,  LinkId = 6, interface PXF, enabled
           link next_send:    0x37022604   channel number:     0
      link bandwidth mult:    33467                 shift:     22
      link bandwidth mult:    33467                 shift:     22
       link aggregate cir:    0x00000000    aggregate eir:     0x00000000
  IOS encapsulation type 1  ARPA
  Min mtu: 14      Max mtu: 1528
  VCCI maptable location = A3340000
  VCCI 9D3  (802.1Q VLAN 1)
    icmp ipaddress 0.0.0.0          timestamp 0
    fib_root 0x0, fib_root_rpf 0x0 cicb_flags 0x00, flags/netmask 0x02
  VCCI 9DB  (802.1Q VLAN 1)
    icmp ipaddress 0.0.0.0          timestamp 0
    fib_root 0x0, fib_root_rpf 0x0 cicb_flags 0x00, flags/netmask 0x02

The following example shows subblocks information for all interfaces:

Router# show pxf cpu subblocks PXF

Interface                 Status   ICB   WQB_ID Fwding Enc VCCI-map VCCI VC
Control Plane             up       0     1      PXF    0   A3000000  1
ATM1/0/0                  initiali 6000  3      disabl 33  A3040000 9CF
ATM1/0/1                  initiali 6001  4      disabl 33  A3060000 9D0
ATM1/0/2                  initiali 6002  5      disabl 33  A3080000 9D1
ATM1/0/3                  initiali 6003  6      disabl 33  A30A0000 9D2
Serial2/0/0               initiali A000  7      disabl 16  A3000004 9D3
Serial2/0/1               initiali A001  8      disabl 16  A3000008 9D4
Serial2/0/2               initiali A002  9      disabl 5   A300000C 9D5
Serial2/0/3               initiali A800  10     disabl 5   A3000010 9D6
Serial2/0/4               initiali A801  11     disabl 5   A3000014 9D7
Serial2/0/5               initiali A802  12     disabl 5   A3000018 9D8
Serial2/0/6               initiali B000  13     disabl 5   A300001C 9D9
Serial2/0/7               initiali B001  14     disabl 5   A3000020 9DA
POS3/0/0                  up       E000  15     PXF    5   A3000024 9DB
Serial4/0/0.1/1/1/1:0     up       12000 27     PXF    16  A3000040 9E7
Serial4/0/0.1/1/1/1:1     up       12001 28     PXF    16  A3000044 9E8
POS5/0/0                  down     16000 16     disabl 5   A3000028 9DC
POS5/0/1                  down     16001 17     disabl 5   A300002C 9DD
POS5/0/2                  down     16002 18     disabl 5   A3000030 9DE
POS5/0/3                  down     16003 19     disabl 5   A3000034 9DF
POS5/0/4                  down     16004 20     disabl 5   A3000038 9E0
POS5/0/5                  down     16005 21     disabl 5   A300003C 9E1
GigabitEthernet6/0/0      down     1A000 22     disabl 1   A32C0000 9E2  1
GigabitEthernet6/0/0.100  down     1A000 22     disabl 1   A32C0000 9EB  100
ATM8/0/0                  up       22000 23     PXF    33  A33C0000 9E3
ATM8/0/0.1                up       22000 23     PXF    33  A33C0000 0    0/33
ATM8/0/0.2                up       22000 23     PXF    33  A33C0000 0    0/34
ATM8/0/0.100              up       22000 23     PXF    33  A33C0000 9EC  30/32
ATM8/0/0.200              up       22000 23     PXF    33  A33C0000 9ED  0/32
ATM8/0/1                  down     22001 24     disabl 33  A33E0000 9E4
ATM8/0/2                  down     22002 25     disabl 33  A3400000 9E5
ATM8/0/3                  down     22003 26     disabl 33  A3420000 9E6
Multilink1                up       0     29     PXF    16  A3000048 2
Multilink2                down     0     36     disabl 16  A300005C 4
Multilink20               up       0     30     PXF    16  A300004C 3
Multilink60230            down     0     31     disabl 16  A3000050 9E9
Multilink60130            down     0     32     disabl 16  A3000054 9EA

Table 87 describes the fields shown in the display.

Table 90 show pxf cpu subblocks Field Descriptions 

Field
Description

Interface

Identifies the interface or subinterface.

Status

Displays the status of the interface:

Administ—The interface has been shut down and is in the administrative down state.

Deleted—The subinterface has been removed from the router's configuration.

Down—The interface is down because of a cable or other connectivity problem.

Initiali—The interface is in the process of initializing.

Reset—The interface is currently being reset.

Up—The interface is up and passing traffic.

ICB

Displays the Interface Control Block (ICB) that is mapped to this interface.

WQB_ID

Displays the Work Queue Block (WQB) identifier for the interface.

Fwding

Displays whether traffic is being forwarded (PXF) or not (disable).

Enc

Identifies the type of encapsulation used on the interface. The most common encapsulation types are:

0 = None

1 = Ethernet ARPA

2 = Ethernet SAP

3 = 802.2 SNAP

5 = Serial, raw HDLC

8 = Serial, LAPB

9 = Serial, X.25

20 = Frame Relay

21 = SMDS

22 = MAC-level packets

27 = Logical Link Control (LLC) 2

28 = Serial, SDLC (primary)

30 = Async SLIP encapsulation

33 = ATM interface

35 = Frame Relay with IETF encapsulation

42 = Dialer encapsulation

46 = Loopback interface

51 = ISDN Q.921

59 = DOCSIS (previously known as MCNS)

61 = Transparent Mode

62 = TDM clear channel

64 = PPP over Frame Relay

65 = IEEE 802.1Q

67 = LAPB terminal adapter

68 = DOCSIS Cable Modem

VCCI-map

Displays the memory address for the Virtually Cool Common Index (VCCI) map table for this particular VCCI.

VCCI

Identifies the VCCI, in hexadecimal, assigned to the interface or subinterface.

VC

Identifies the virtual circuit (VC).



Related Commands

Command
Description

clear pxf

Clears PXF counters and statistics.

debug pxf

Displays PXF debugging output.

show ip mroute

Displays the contents of the IP multicast routing table.

show pxf cpu tbridge

Displays PXF CPU statistics for transparent bridging.

show pxf microcode

Displays identifying information for the microcode currently loaded on the PXF.


show pxf cpu vcci

To display Virtually Cool Common Index (VCCI) to interface mapping information on the Parallel eXpress Forwarding (PXF), use the show pxf cpu vcci command in privileged EXEC mode.

show pxf cpu vcci [summary]

Syntax Description

summary

(Optional) Displays VCCI allocation information.


Command Modes

Privileged EXEC (#)

Command History

Release
Modification

12.2S

This command was introduced.


Usage Guidelines

The VCCI is an index that uniquely identifies each interface or subinterface in the PXF and it maps that interface to the appropriate set of services and features. This command is useful to verify the number of VCCIs that are used and available.

The Cisco 10000 series router has 65,536 VCCIs. A VCCI is assigned to each individual routed interface. A VCCI is not assigned to virtual template interfaces and loopbacks.

Examples

The following example shows how to display the number of used and available VCCIs. The fields shown in the display are self-explanatory.

Router# show pxf cpu vcci summary 

  VCCI usage summary

                   Maximum  Used     Available
  Multilink VCCI   2500     0        2500 
  Other VCCI       63023    14       63009

Related Commands

Command
Description

show pxf cpu policy-data

Displays QoS policy data index usage statistics.


show pxf crash

To display Parallel eXpress Forwarding (PXF) crash information, use the show pxf crash command in privileged EXEC mode.

show pxf crash

Syntax Description

This command has no arguments or keywords.

Command Modes

Privileged EXEC (#)

Command History

Release
Modification

12.1(1)E

This command was introduced on the Cisco 10000 series router.

12.1(5)T

This command was integrated into Cisco IOS Release 12.1(5)T.

12.2(31)SB

This command was integrated into Cisco IOS Release 12.2(31)SB.

12.2SX

This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.


Examples

The following example shows crash information as a result of a PXF direct memory access (DMA) error. The PXF crash information is typically stored in bootflash.

Router# show pxf crash

Summary of bootflash:pxf_crashinfo_20060117-152035

Time of crash was 15:20:35 UTC Tue Jan 17 2006

PXF DMA Error - End of Descriptor Before Cmd Byte Length Exhausted

Current microcode:
        file=system:pxf/c10k2-11-ucode.108.0.0.0,
        version=108.0.0.0,
        description=Nightly Build Software created Sat 19-Nov-05 00:12

Table 89 describes the significant fields shown in the display.

Table 91 show pxf crash Field Descriptions 

Field
Description

Summary of bootflash:

Displays the filename in bootflash where the PXF crash information is stored. The filename format includes the date and time of the PXF crash.

Time of crash

Displays the date of the PXF crash.

UTC

Displays the Universal Coordinated Time (UTC) of the PXF crash.

Current microcode

Displays identifying information for the microcode currently running on the PXF.


Related Commands

Command
Description

show pxf statistics

Displays a summary of PXF statistics.


show pxf dma

To display the current state of direct memory access (DMA) buffers, error counters, and registers on the Parallel eXpress Forwarding (PXF), use the show pxf dma command in privileged EXEC mode.

show pxf dma [buffers | counters | reassembly | registers]

Cisco 10000 Series Router (PRE3 only)

show pxf dma [buffers | counters | reassembly | registers] [brief | config | errors | status]

Syntax Description

buffers

(Optional) Displays PXF DMA buffers information.

counters

(Optional) Displays packet and error counters for the PXF DMA engine.

reassembly

(Optional) Displays PXF reassembly table usage information.

registers

(Optional) Displays PXF DMA registers information.

brief

(Optional) Displays PXF DMA information, including the initialization state of each block in the PXF API and any errors that occurred.

Note This option is available on the PRE3 only.

config

(Optional) Displays a configuration summary of the registers in each of the PXF DMA blocks.

Note This option is available on the PRE3 only.

errors

(Optional) Displays the errors that occurred in each of the PXF DMA blocks.

Note This option is available on the PRE3 only.

status

(Optional) Displays the initialization state of each PXF DMA block. In normal operation, all blocks display the enabled state.

Note This option is available on the PRE3 only.


Command Modes

Privileged EXEC (#)

Command History

Release
Modification

12.2S

This command was introduced.

12.3(7)XI

This command was integrated into Cisco IOS Release 12.3(7)XI and implemented on the Cisco 10000 series router for the PRE2.

12.2(31)SB2

This command was integrated into Cisco IOS Release 12.2(31)SB2 and implemented on the Cisco 10000 series router for the PRE3.


Examples

The following example shows PXF DMA buffers information:

Router# show pxf dma buffers

PXF To-RP DMA Ring Descriptors & Buffers:

     Descriptor       Buffer        Buffer      Descriptor
     Address          Address       Length(b)   Flags
0    0x0CA06340       0x0AC097C0      512       0x0002
1    0x0CA06350       0x0AC088C0      512       0x0002
2    0x0CA06360       0x0AC07C40      512       0x0002
3    0x0CA06370       0x0AC0B5C0      512       0x0002
4    0x0CA06380       0x0AC0CC40      512       0x0002
5    0x0CA06390       0x0AC08640      512       0x0002
6    0x0CA063A0       0x0AC0C240      512       0x0002
7    0x0CA063B0       0x0AC08B40      512       0x0002
8    0x0CA063C0       0x0AC0AE40      512       0x0002
9    0x0CA063D0       0x0AC0BAC0      512       0x0002
10   0x0CA063E0       0x0AC0C9C0      512       0x0002
11   0x0CA063F0       0x0AC09CC0      512       0x0002
12   0x0CA06400       0x0AC0C740      512       0x0002
13   0x0CA06410       0x0AC0A6C0      512       0x0002
14   0x0CA06420       0x0AC0B0C0      512       0x0002
15   0x0CA06430       0x0AC09040      512       0x0002
16   0x0CA06440       0x0AC0A440      512       0x0002
17   0x0CA06450       0x0AC065C0      512       0x0002
18   0x0CA06460       0x0AC06FC0      512       0x0002
19   0x0CA06470       0x0AC06340      512       0x0002
20   0x0CA06480       0x0AC07240      512       0x0002
21   0x0CA06490       0x0AC092C0      512       0x0002
22   0x0CA064A0       0x0AC0D140      512       0x0002
23   0x0CA064B0       0x0AC0C4C0      512       0x0002
24   0x0CA064C0       0x0AC07740      512       0x0002
25   0x0CA064D0       0x0AC09540      512       0x0002
26   0x0CA064E0       0x0AC0A940      512       0x0002
27   0x0CA064F0       0x0AC06840      512       0x0002
28   0x0CA06500       0x0AC08140      512       0x0002
29   0x0CA06510       0x0AC06D40      512       0x0002
30   0x0CA06520       0x0AC07EC0      512       0x0002
31   0x0CA06530       0x0AC0ABC0      512       0x0003

PXF From-RP DMA Ring Descriptors & Buffers:

     Descriptor       Buffer        Buffer      Descriptor    Context
     Address          Address       Length(b)   Flags         Bit
0    0x0CA06580       0x00000000        0       0x0000        Not set
1    0x0CA06590       0x00000000        0       0x0000        Not set
2    0x0CA065A0       0x00000000        0       0x0000        Not set
3    0x0CA065B0       0x00000000        0       0x0000        Not set
4    0x0CA065C0       0x00000000        0       0x0000        Not set
5    0x0CA065D0       0x00000000        0       0x0000        Not set
6    0x0CA065E0       0x00000000        0       0x0000        Not set
7    0x0CA065F0       0x00000000        0       0x0000        Not set
8    0x0CA06600       0x00000000        0       0x0000        Not set
9    0x0CA06610       0x00000000        0       0x0000        Not set
10   0x0CA06620       0x00000000        0       0x0000        Not set
11   0x0CA06630       0x00000000        0       0x0000        Not set
12   0x0CA06640       0x00000000        0       0x0000        Not set
13   0x0CA06650       0x00000000        0       0x0000        Not set
14   0x0CA06660       0x00000000        0       0x0000        Not set
15   0x0CA06670       0x00000000        0       0x0001        Not set

Table 87 describes the fields shown in the display.

Table 92 show pxf dma Field Descriptions 

Field
Description

Descriptor Address

Memory address pointing to the descriptor for this buffer.

Buffer Address

Address of this buffer in memory.

Buffer Length

Length, in bytes, of this particular buffer.

Descriptor Flags

Internal flags identifying this buffer's use and status.

Context Bit

State of the context bit which is set when the buffer is currently in use by a context (the basic unit of packet processing).


Related Commands

Command
Description

clear pxf

Clears PXF counters and statistics.

show pxf cpu

Displays PXF CPU statistics.

show pxf microcode

Displays the microcode version running on the PXF.


show pxf feature cef

To display Parallel eXpress Forwarding (PXF) routing feature tables for Cisco Express Forwarding, use the show pxf feature cef command in user EXEC or privileged EXEC mode.

show pxf feature cef entry

Syntax Description

entry

Display the PXF entry.


Command Modes

User EXEC (>)
Privileged EXEC (#)

Command History

Release
Modification

12.1(1)E

This command was introduced.

12.1(5)T

This command was integrated into Cisco IOS Release 12.1(5)T.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.2SX

This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.


Examples

The following is sample output from the show pxf feature cef command. The fields shown in the display are self-explanatory.

Router# show pxf feature cef entry

Shadow 16-4-4-8 PXF Mtrie:
  41 leaves, 1968 leaf bytes, 15 nodes, 267000 node bytes
  5 invalidations
  46 prefix updates
  refcounts: 66746 leaf, 66720 node
 
Prefix/Length        Refcount   Parent
0.0.0.0/0           62282    
0.0.0.0/32          3           0.0.0.0/0
171.22.12.128/27    34          0.0.0.0/0
171.22.12.128/32    3           171.22.12.128/27
171.22.12.129/32    3           171.22.12.128/27
171.22.12.130/32    3           171.22.12.128/27
171.22.12.131/32    3           171.22.12.128/27
171.22.12.147/32    3           171.22.12.128/27

Related Commands

Command
Description

show pxf feature nat

Displays PXF routing feature tables for NAT.


show pxf feature cef vrf

To display the routing feature tables for Virtual Private Network (VPN) routing and forwarding instances (VRFs) on the Parallel eXpress Forwarding (PXF) path, use the show pxf feature cef vrf command in privileged EXEC mode.

show pxf feature cef vrf vpn-name

Syntax Description

vpn-name

Name of the VPN to display.


Command Modes

Privileged EXEC (#)

Command History

Release
Modification

12.2(15)B

This command was introduced.

12.3(4)T

This command was integrated into Cisco IOS Release 12.3(4)T.


Usage Guidelines

Use this command to display VRF PXF routing feature tables for a specified VPN for Cisco Express Forwarding. This command also displays information about prefix and MTRIE resource usage.

Examples

The following is sample output for the show pxf feature cef vrf command when it is used to display information about VRF vpn1:

Router# show pxf feature cef vrf vpn1

Shadow 8-8-4-4-8 PXF Mtrie:
  51 leaves, 2448 leaf bytes, 92 nodes, 56352 node bytes
  10 invalidations
  61 prefix updates
  refcounts: 3666 leaf, 3733 node

Prefix/Length        Refcount   Parent           Address     Shadow
0.0.0.0/32            3                              0xC0047218 0x62CAF2E8
10.5.0.0/16           558                            0xC0047278 0x62CAF108
10.5.0.0/32           3           10.5.0.0/16        0xC0047268 0x62CAEE08
10.5.0.1/32           3           10.5.0.0/16        0xC0047260 0x62CAEA18
10.5.0.2/32           3           10.5.0.0/16        0xC0047388 0x62CAEA48
10.5.0.255/32         3           10.5.0.0/16        0xC0047270 0x62CAF0D8
10.30.1.0/16          288                            0xC0047360 0x62CAEB38
10.30.1.1/32          3           10.30.1.0/16       0xC0047350 0x62CAEB98
10.70.0.0/32          3                              0xC00472C0 0x62CAEEF8
10.70.1.1/32          3                              0xC0047358 0x62CAEB68
10.70.1.2/32          3                              0xC0047368 0x62CAEB08
10.70.1.3/32          3                              0xC0047370 0x62CAEAD8
10.70.1.4/32          3                              0xC0047378 0x62CAEAA8
70.1.1.5/32           3                              0xC0047380 0x62CAEA78
224.0.0.0/24          3                              0xC0047228 0x62CAF288
255.255.255.255/32    3                              0xC0047220 0x62CAF2B8
========================================
5 routes with less specific overlapping parent route

Table 93 describes the significant fields shown in the display.

Table 93 show pxf feature cef vrf Field Descriptions

Field
Description

Shadow 8-8-4-4-8 PXF Mtrie

MTRIE lookup table index structures.

51 leaves

All created leaves for all MTRIEs.

2448 leaf bytes

Leaf byte counter. When a new leaf is created, the leaf byte counter is incremented by the size of the leaf structure.

92 nodes

All created nodes for all MTRIEs.

56352 node bytes

Node byte counter. When a new node is created, the node byte counter is incremented.

10 invalidations

Invalidations counter. When a route (represented by a leaf) is deleted from an MTRIE, the invalidations counter is incremented. This counter includes all MTRIEs.

61 prefix updates

IP prefix counter. When an IP prefix (represented by a leaf) is added to the MTRIE, the IP prefix counter is incremented. This counter includes all MTRIEs.

refcounts

Counters associated with references between leaves.

3666 leaf

MTRIEs have a leaf lock and a leaf free function. The leaf lock function increments the leaf refcount. The leaf free function decrements the leaf refcount. The leaf lock and leaf free functions prevent a leaf from being freed (deleted) while the leaf is still being referenced. This counter includes all MTRIEs.

3733 node

Node counter. When a child node is added to another node, the node to which the child node is added becomes a parent node. The node counter is decremented when a child node is deleted. This counter includes all MTRIEs.

Prefix/Length

The IP address and subnet mask of a leaf.

Refcount

The number of leaves that reference a specified leaf. The refcount counter is incremented when the leaf lock function is called and decremented when the leaf free function is called.

Parent

When you add a less specific route to a more specific route, the more specific route has a back pointer that points to the less specific route.

Address

The address of the memory for the specified leaf.

Shadow

The shadow address in Route Processor memory for the specified leaf.


Related Commands

Command
Description

show pxf feature cef

Displays PXF routing feature tables for CEF.

show pxf feature nat

Displays PXF routing feature tables for NAT.


show pxf feature nat

To display Parallel eXpress Forwarding (PXF) routing tables for Network Address Translation (NAT), use the show pxf feature nat command in user EXEC or privileged EXEC mode.

show pxf feature nat [entry | stat | tcp]

Syntax Description

entry

Displays NAT information.

stat

Displays NAT processing information.

tcp

Displays NAT TCP logging information.


Command Modes

User EXEC (>)
Privileged EXEC (#)

Command History

Release
Modification

12.1(1)E

This command was introduced.

12.1(5)T

This command was integrated into Cisco IOS Release 12.1(5)T.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.2SX

This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.


Examples

The following is sample output from the show pxf feature nat command. The fields shown in the display are self-explanatory.

Router# show pxf feature nat 

--- 171.22.12.175      192.168.0.129      ---                ---
--- 171.22.12.163      192.168.0.7        ---                ---
--- 171.22.12.161      192.168.0.13       ---                ---
--- 171.22.12.162      192.168.0.3        ---                ---
--- 171.22.12.165      192.168.0.8        ---                ---
--- 171.22.12.168      192.168.0.14       ---                ---
--- 171.22.12.170      192.168.0.12       ---                ---
--- 171.22.12.166      192.168.0.15       ---                ---
--- 171.22.12.164      192.168.0.16       ---                ---

Related Commands

Command
Description

show pxf feature cef

Displays PXF routing feature tables for Cisco Express Forwarding.


show pxf interface

To display a summary of the interfaces on the router and the Parallel eXpress Forwarding (PXF) features and capabilities enabled on these interfaces, use the show pxf interface command in privileged EXEC mode.

show pxf interface interface-name [detail]

Syntax Description

interface-name

Name of the interface.

detail

(Optional) Displays detailed information for all PXF interfaces on the router.


Command Modes

Privileged EXEC (#)

Command History

Release
Modification

12.2S

This command was introduced.

12.3(7)XI1

This command was integrated into Cisco IOS Release 12.3(7)XI1.

12.2SX

This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.


Usage Guidelines

If you do not specify an interface, the command displays a summary of the statistics for all PXF interfaces on the router.

Examples

The following example shows PXF statistics for serial interface 1/0/0. The significant fields shown in the display are self-explanatory.

Router# show pxf interface s1/0/0

ed10#sho pxf interface s1/0/0
Serial1/0/0 is up, enabled, PXF enabled, IOS encap PPP     (16)
 Last clearing of Serial1/0/0 counters: 00:06:29
 91 packets input, (1934 bytes)

Total PXF input errors (pkts/bytes):          0/0         

PXF output queues:
        Class        ID     Length/Max   Outputs (pkts/bytes)  Drops
   0 class-default   276     0/1024         0/0                  0
  15             -   275     0/32          91/1953               0

Slot 1/0: FBB Rx:0x00000000 OCQ debug:0x00001040, qN_entry_cnt[5:0]: 0
          PXF DMA RE drops: 0/0,  Null config drops: 0/0
          Last clearing of slot 1/0 counters: 00:06:29

Related Commands

Command
Description

clear pxf

Clears PXF counters and statistics.

show pxf statistics

Displays chassis-wide, summary PXF statistics.


show pxf microcode

To display identifying information for the microcode currently loaded on the Parallel eXpress Forwarding (PXF), use the show pxf microcode command in privileged EXEC mode.

show pxf microcode

Syntax Description

This command has no arguments or keywords.

Command Modes

Privileged EXEC (#)

Command History

Release
Modification

12.2S

This command was introduced.

12.3(7)XI

This command was integrated into Cisco IOS Release 12.3(7)XI.


Examples

The following example shows the microcode version that is currently loaded on the PXF:

Router# show pxf microcode

PXF complex: 4 Toasters 8 Columns total
PXF processor tmc0 is running.
PXF processor tmc1 is running.
PXF processor tmc2 is running.
PXF processor tmc3 is running.

Loaded microcode: system:pxf/c10k2-11-ucode.6.1.3
        Version: 6.1.3
        Release Software created Sun 20-Nov-05 14:06
        Signature: 0d2b395c1083872793586f9cec47d7b3
        Microcode load attempted 1 time(s), latest 2w6d ago
        tmc0 FG_PC=0 BG_PC=6 WDog=1024 MinPhase=23 SecPreScalerTimer=11542680 MS
ecPreScalerTimer=153600
        tmc1 FG_PC=0 BG_PC=6 WDog=1024 MinPhase=23 SecPreScalerTimer=11542680 MS
ecPreScalerTimer=153600
        tmc2 FG_PC=0 BG_PC=6 WDog=1024 MinPhase=23 SecPreScalerTimer=11542680 MS
ecPreScalerTimer=153600
        tmc3 FG_PC=0 BG_PC=6 WDog=1024 MinPhase=23 SecPreScalerTimer=11542680 MS
ecPreScalerTimer=154 

Table 94 describes the fields shown in the display.

Table 94 show pxf microcode Field Descriptions 

Field
Description

PXF complex

The number of PXF processors, their associate memory columns, and their current status.

Loaded microcode

The source and filename for the microcode that is currently loaded on the PXF processor.

Version

The microcode version.

Release Software created

The time and date the current microcode was compiled.

Signature

The signature in the microcode version.

Microcode load attempted

The number of times the PXF processor has loaded the microcode since the Cisco IOS image was loaded at system boot. Also, shows the time (in days and hours) since the last successful load of the microcode.

tmc#

The current program counters and configuration for the PXF processors.


Related Commands

Command
Description

clear pxf

Clears PXF counters and statistics.

show pxf cpu statistics

Displays PXF CPU statistics.

show pxf dma

Displays PXF DMA information.


show pxf netflow

To display the NetFlow Parallel eXpress Forwarding (PXF) counters, use the show pxf netflow command in privileged EXEC mode.

show pxf netflow

Syntax Description

This command has no arguments or keywords.

Command Modes

Privileged EXEC (#)

Command History

Release
Modification

12.2S

This command was introduced.

12.3(7)XI

This command was integrated into Cisco IOS Release 12.3(7)XI.


Examples

The following example shows the NetFlow PXF statistics. The fields shown in the display are self-explanatory.

Router# show pxf netflow

NetFlow debug counters
        timeout activity:   0
        timeout inactivity: 9785
        forced age:         0
        export busy:        1
        export locked:      62
        export noswap:      2
        accumulate:         1296898
        new flow:           9808

(unreliable) ICM counters 
        records pending :   0
        live flows :        0
 
NetFlow PXF Config Registers
        PXF Inactive Timeout: 90000
        PXF Active Timeout:   90000

Related Commands

Command
Description

show pxf cpu statistics

Displays PXF CPU statistics.

show pxf statistics

Displays chassis-wide, summary PXF statistics.


show pxf stall-monitoring

To display the configuration and operating status details of the PXF stall monitor (PSM), use the show pxf stall-monitoring command in privileged EXEC mode. The show pxf stall-monitoring command also displays the number of stalls on the PSM after it was last enabled.

show pxf stall-monitoring [counters | reset {active-status | cob-fib | cob-tib | pxf-drop} subslot sub-slot]

Syntax Description

counters

Displays statistical information for all counters.

reset

Displays the following counters:

active-status—Displays the active status on the specified subslot.

cob-fib—Displays the Cobalt FIB counter on the specified subslot.

cob-tib—Displays the Cobalt TIB counter on the specified subslot.

pxf-drop—Displays the PXF per RSRC drop counter on the specified subslot.

subslot sub slot—Displays information about the specified subslot.


Command Modes

Privileged EXEC (#)

Command History

Release
Modification

12.2(33)XNE

This command was introduced.


Examples

The following example displays a sample output of the show pxf stall-monitoring command:

Router# show pxf stall-monitoring

pxf stall-monitoring : Enabled
Stall History
=============
Stall Threshold Configuration
=============================
Primary Action = LC-reset Threshold = 3 (default)
Primary Action = HT-reset Threshold = 3 (default)

Secondary action = SSO SwitchOverRouter#

The fields displayed are self-explanatory.

The following example displays a sample output of the show pxf stall-monitoring counters command:

Router# show pxf stall-monitoring counters

To RP Counters
==============
IOS To RP Counter = 20665
PXF To RP Drop Counter = 0
Current Counter Values
======================
Slot 0 Subslot 0 Cob TIB = 0 Cob FIB = 0 PXF Drop = 0
Slot 0 Subslot 1 Cob TIB = 0 Cob FIB = 0 PXF Drop = 0
Slot 1 Subslot 0 Cob TIB = 2368 Cob FIB = 0 PXF Drop = 0
Slot 1 Subslot 1 Cob TIB = 0 Cob FIB = 0 PXF Drop = 0
Slot 2 Subslot 0 Cob TIB = 0 Cob FIB = 0 PXF Drop = 0
Slot 2 Subslot 1 Cob TIB = 0 Cob FIB = 0 PXF Drop = 0
Slot 3 Subslot 0 Cob TIB = 0 Cob FIB = 0 PXF Drop = 0
Slot 3 Subslot 1 Cob TIB = 0 Cob FIB = 0 PXF Drop = 0
Slot 4 Subslot 0 Cob TIB = 0 Cob FIB = 0 PXF Drop = 0
Slot 4 Subslot 1 Cob TIB = 0 Cob FIB = 0 PXF Drop = 0
Slot 5 Subslot 0 Cob TIB = 6162 Cob FIB = 6204 PXF Drop = 0
Slot 5 Subslot 1 Cob TIB = 6101 Cob FIB = 6065 PXF Drop = 0
Slot 5 Subslot 2 Cob TIB = 0 Cob FIB = 0 PXF Drop = 0
Slot 5 Subslot 3 Cob TIB = 0 Cob FIB = 0 PXF Drop = 0
Slot 7 Subslot 0 Cob TIB = 8402 Cob FIB = 8402 PXF Drop = 0
Slot 7 Subslot 1 Cob TIB = 0 Cob FIB = 0 PXF Drop = 0
Slot 8 Subslot 0 Cob TIB = 0 Cob FIB = 0 PXF Drop = 0
Slot 8 Subslot 1 Cob TIB = 0 Cob FIB = 0 PXF Drop = 0
Line Card Participant Status
============================
Slot 1 Subslot 0 = 1
Slot 1 Subslot 1 = 0
Slot 2 Subslot 0 = 0
Slot 2 Subslot 1 = 0
Slot 3 Subslot 0 = 0
Slot 3 Subslot 1 = 0
Slot 4 Subslot 0 = 0
Slot 4 Subslot 1 = 0
Slot 5 Subslot 0 = 0
Slot 5 Subslot 1 = 1
Slot 5 Subslot 2 = 0
Slot 5 Subslot 3 = 0
Slot 7 Subslot 0 = 1
Slot 7 Subslot 1 = 0
Slot 8 Subslot 0 = 1
Slot 8 Subslot 1 = 0
Line Card Active Status
=======================
Slot 1 Subslot 0 = 0
Slot 1 Subslot 1 = 0
Slot 2 Subslot 0 = 0
Slot 2 Subslot 1 = 0
Slot 3 Subslot 0 = 0
Slot 3 Subslot 1 = 0
Slot 4 Subslot 0 = 0
Slot 4 Subslot 1 = 0
Slot 5 Subslot 0 = 0
Slot 5 Subslot 1 = 1
Slot 5 Subslot 2 = 0
Slot 5 Subslot 3 = 0
Slot 7 Subslot 0 = 0
Slot 7 Subslot 1 = 0
Slot 8 Subslot 0 = 0
Slot 8 Subslot 1 = 0

The fields displayed are self-explanatory.

The following example displays a sample output of the show pxf stall-monitoring reset command:

Router# show pxf stall-monitoring reset active-status subslot 1/0

pxf stall-monitoring : Enabled
 0

Related Commands

Command
Description

hw-module pxf stall-monitoring

Enables PXF stall monitor on the Cisco 10000 series router and configures default threshold values before the LC and HTDP resets.


show pxf statistics

To display summary Parallel eXpress Forwarding (PXF) statistics, use the show pxf statistics command in privileged EXEC mode.

show pxf statistics {context | diversion | drop [detail] | ip | ipv6}

Syntax Description

context

Displays context statistics.

diversion

Displays traffic diverted from the PXF.

drop [detail]

Displays packets dropped by the PXF. The detail option provides detailed information.

ip

Displays IP and ICMP statistics.

ipv6

Displays IPv6 statistics.


Command Modes

Privileged EXEC (#)

Command History

Release
Modification

12.0(22)S

This command was introduced on the Cisco 10000 series router.

12.2(28)SB

This command was integrated into Cisco IOS Release 12.2(28)SB.

12.3(7)XI1

This command was integrated into Cisco IOS Release 12.3(7)XI1.

12.2(31)SB

This command was integrated into Cisco IOS Release 12.2(31)SB.


Examples

The following example shows a summary of PXF IP statistics:

Router# show pxf statistics ip 

Chassis-wide PXF forwarding counts
   IP inputs 0, forwarded 0, punted 0
   IP dropped 0, no adjacency 0, no route 0
   IP unicast RPF 0, unresolved 0

   ICMP created 0, Unreachable sent 0, TTL expired sent 0
   ICMP echo requests 0, replies sent 0
   ICMP checksum errors 0

   IP packets fragmented 0, total fragments 0, failed 0
   IP don't-fragment 0, multicast don't-fragment 0

   IP mcast total 0, switched 0, punted 0, failed 0
   IP mcast drops 0, RPF 0, input ACL 0, output ACL + taildrops 0
Last clearing of PXF forwarding counters:never

The following example shows a summary of PXF statistics for dropped packets:

Router# show pxf statistics drop 

PXF input drops:
 Unassigned drops (pkts/bytes):                        0/0
Last clearing of drop counters: never

The following example shows detailed PXF statistics for dropped packets:

Router# show pxf statistics drop detail

PXF input drops:
 Unassigned drops (pkts/bytes):                        0/0

PXF Unassigned input drop details:
 (These input drops are not assigned to a particular PXF interface.)
                        packets            bytes
    generic             0                  0
    mpls_no_eos         0                  0
    fib_zero_dest       0                  0
    fib_drop_null       0                  0
    fib_icmp_no_adj     0                  0
    fib_icmp_bcast_dst  0                  0
    mfib_ttl_0          0                  0
    mfib_disabled       0                  0
    mfib_rpf_failed     0                  0
    mfib_null_oif       0                  0
    tfib_rp_flag        0                  0
    tfib_eos_violation  0                  0
    tfib_nonip_expose   0                  0
    tfib_label_invalid  0                  0
    tfib_path_unknown   0                  0
    tfib_nonip_ttl_exp  0                  0
    icmp_unrch_interval 0                  0
    icmp_on_icmp        0                  0
    icmp_bad_hdr        0                  0
    icmp_multicast      0                  0
    icmp_frag           0                  0
    macr_bad_tag_num    0                  0
    no_touch            0                  0
    enq_id_0            0                  0
    no_pkt_handles      0                  0
    l2_unsupp_drop      0                  0
    ipm_replay_full     0                  0
    bad_atm_arp         0                  0
   nested_fragmentation 0                  0
    l2less drop packets 0
    l2tp_payload_encap  0                  0
    re_bit[00]          0                  0
          [01]          0                  0
          [02]          0                  0
          [03]          0                  0
          [04]          0                  0
          [05]          0                  0
          [06]          0                  0
          [07]          0                  0
          [08]          0                  0
          [09]          0                  0
          [10]          0                  0
.
.
.

The following example shows summarized statistics for traffic diverted from the PXF:

Router# show pxf statistics diversion 

Diversion Cause Stats:
  divert    = 0
  encap     = 0
  clns_isis = 0
  clns      = 0
  cdp       = 0
  cgmp      = 0
  arp       = 1
  rarp      = 0
  mpls_ctl  = 0
  keepalive = 0
  ppp_cntrl = 449
  fr_lmi    = 0
  atm ilmi  = 0
  oam f4    = 0
  oam f5 ete= 0
  oam f5 seg= 0
  mlfr lip  = 0
.
.
.

Related Commands

Command
Description

clear pxf

Clears PXF counters and statistics.

show pxf cpu statistics

Displays PXF CPU statistics.


show pxf xcm

To display Parallel eXpress Forwarding (PXF) External Column Memory (XCM) information, use the show pxf xcm command in privileged EXEC mode.

show pxf xcm

Syntax Description

This command has no arguments or keywords.

Command Modes

Privileged EXEC (#)

Command History

Release
Modification

12.2S

This command was introduced.

12.3(7)XI

This command was integrated into Cisco IOS Release 12.3(7)XI.


Examples

The following example shows XCM information for each PXF processor:

Router# show pxf xcm

Toaster 0:
    Number of Columns: 2
    Proc ID: 0x00000004 = TMC_X72
    ASIC Revision: 0x00000001 = T3-ECC
    XCM0 type:FCRAM, size = 67108864
    ECC is enabled for column 0
        XCM AB Config Register: 0x024703B9
        XCM CD Config Register: 0x024703B9
        XCM Exception Type Register: 0x00000000
        FCRAM-A Counters
        Number of ECC single bit errors: 0
        FCRAM-B Counters
        Number of ECC single bit errors: 0
        FCRAM-C Counters
        Number of ECC single bit errors: 0
        FCRAM-D Counters
        Number of ECC single bit errors: 0
    XCM1 type:FCRAM, size = 67108864
    ECC is enabled for column 1
        XCM AB Config Register: 0x024703B9
        XCM CD Config Register: 0x024703B9
        XCM Exception Type Register: 0x00000000
        FCRAM-A Counters
        Number of ECC single bit errors: 0
        FCRAM-B Counters
        Number of ECC single bit errors: 0
        FCRAM-C Counters
        Number of ECC single bit errors: 0
        FCRAM-D Counters
        Number of ECC single bit errors: 0
Toaster 1:
    Number of Columns: 2
    Proc ID: 0x00000004 = TMC_X72
    ASIC Revision: 0x00000001 = T3-ECC
    XCM0 type:FCRAM, size = 67108864
    ECC is enabled for column 0
        XCM AB Config Register: 0x024703B9
        XCM CD Config Register: 0x024703B9
        XCM Exception Type Register: 0x00000000
        FCRAM-A Counters
        Number of ECC single bit errors: 0
        FCRAM-B Counters
        Number of ECC single bit errors: 0
        FCRAM-C Counters
        Number of ECC single bit errors: 0
        FCRAM-D Counters
        Number of ECC single bit errors: 0
    XCM1 type:FCRAM, size = 67108864
    ECC is enabled for column 1
        XCM AB Config Register: 0x024703B9
        XCM CD Config Register: 0x024703B9
        XCM Exception Type Register: 0x00000000
        FCRAM-A Counters
        Number of ECC single bit errors: 0

        FCRAM-B Counters
        Number of ECC single bit errors: 0
        FCRAM-C Counters
        Number of ECC single bit errors: 0
        FCRAM-D Counters
        Number of ECC single bit errors: 0
Toaster 2:
    Number of Columns: 2
    Proc ID: 0x00000004 = TMC_X72
    ASIC Revision: 0x00000001 = T3-ECC
    XCM0 type:FCRAM, size = 67108864
    ECC is enabled for column 0
        XCM AB Config Register: 0x024703B9
        XCM CD Config Register: 0x024703B9
        XCM Exception Type Register: 0x00000000
        FCRAM-A Counters
        Number of ECC single bit errors: 0
        FCRAM-B Counters
        Number of ECC single bit errors: 0
        FCRAM-C Counters
        Number of ECC single bit errors: 0
        FCRAM-D Counters
        Number of ECC single bit errors: 0
    XCM1 type:FCRAM, size = 67108864
    ECC is enabled for column 1
        XCM AB Config Register: 0x024703B9
        XCM CD Config Register: 0x024703B9
        XCM Exception Type Register: 0x00000000
        FCRAM-A Counters
        Number of ECC single bit errors: 0
        FCRAM-B Counters
        Number of ECC single bit errors: 0
        FCRAM-C Counters
        Number of ECC single bit errors: 0
        FCRAM-D Counters
        Number of ECC single bit errors: 0
Toaster 3:
    Number of Columns: 2
    Proc ID: 0x00000004 = TMC_X72
    ASIC Revision: 0x00000001 = T3-ECC
    XCM0 type:FCRAM, size = 67108864
    ECC is enabled for column 0
        XCM AB Config Register: 0x024703B9
        XCM CD Config Register: 0x024703B9
        XCM Exception Type Register: 0x00000000
        FCRAM-A Counters
        Number of ECC single bit errors: 0
        FCRAM-B Counters
        Number of ECC single bit errors: 0
        FCRAM-C Counters
        Number of ECC single bit errors: 0
        FCRAM-D Counters
        Number of ECC single bit errors: 0
    XCM1 type:FCRAM, size = 67108864
    ECC is enabled for column 1
        XCM AB Config Register: 0x024703B9
        XCM CD Config Register: 0x024703B9
        XCM Exception Type Register: 0x00000000
        FCRAM-A Counters
        Number of ECC single bit errors: 0
        FCRAM-B Counters
        Number of ECC single bit errors: 0
        FCRAM-C Counters
        Number of ECC single bit errors: 0
        FCRAM-D Counters
        Number of ECC single bit errors: 0

Table 95 describes the fields shown in the display.

Table 95 show pxf xcm Field Descriptions 

Field
Description

The following fields appear for each PXF processor.

Toaster #

Identifies the PXF processor.

Number of Columns

Displays the number of memory columns on the PXF processor.

Proc ID

Displays the processor type (TMC is Toaster Memory Column).

ASIC Revision

Displays the internal version number of the PXF processor.

The following fields appear for each XCM memory column.

XCM type

Displays the type and size, in bytes, of memory used in this particular column.

ECC is enabled for column

Displays whether Error Code Correction (ECC) checking is enabled or disabled for this memory column.

XCM Config Register and XCM Exception Type Register

Displays the contents of these two registers for the memory column.

Number of ECC single bit errors

Displays the number of single-bit errors detected in memory.


Related Commands

Command
Description

show pxf cpu

Displays PXF CPU statistics.

show pxf microcode

Displays the microcode version currently loaded on the PXF.


show route-map ipc

To display counts of the one-way route map interprocess communication (IPC) messages sent from the rendezvous point (RP) to the Versatile Interface Processor (VIP) when NetFlow policy routing is configured, use the show route-map ipc command in privileged EXEC mode.

show route-map ipc

Syntax Description

This command has no arguments or keywords.

Command Modes

Privileged EXEC (#)

Command History

Release
Modification

12.0(3)T

This command was introduced.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.2SX

This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.


Usage Guidelines

This command displays the counts of one-way route map IPC messages from the RP to the VIP when NetFlow policy routing is configured. If you execute this command on the RP, the messages are shown as "Sent." If you execute this command on the VIP console, the IPC messages are shown as "Received."

Examples

The following is sample output of the show route-map ipc command when it is executed on the RP:

Router# show route-map ipc

Route-map RP IPC Config Updates Sent
Name: 4
Match access-list: 2
Match length: 0
Set precedence: 1
Set tos: 0
Set nexthop: 4
Set interface: 0
Set default nexthop: 0
Set default interface: 1
Clean all: 2

The following is sample output of the show route-map ipc command when it is executed on the VIP:

Router# show route-map ipc

Route-map LC IPC Config Updates Received
Name: 4
Match access-list: 2
Match length: 0
Set precedence: 1
Set tos: 0
Set nexthop: 4
Set interface: 0
Set default nexthop: 0
Set default interface: 1
Clean all: 2

Table 96 describes the significant fields shown in the display.

Table 96 show route-map ipc Field Descriptions 

Field
Description

Route-map RP IPC Config Updates Sent

Indicates that IPC messages are being sent from the RP to the VIP.

Name

Number of IPC messages sent about the name of the route map.

Match access-list

Number of IPC messages sent about the access list.

Match length

Number of IPC messages sent about the length to match.

Set precedence

Number of IPC messages sent about the precedence.

Set tos

Number of IPC messages sent about the type of service (ToS).

Set nexthop

Number of IPC messages sent about the next hop.

Set interface

Number of IPC messages sent about the interface.

Set default nexthop

Number of IPC messages sent about the default next hop.

Set default interface

Number of IPC messages sent about the default interface.

Clean all

Number of IPC messages sent about clearing the policy routing configuration from the VIP. When dCEF is disabled and reenabled, the configuration related to policy routing must be removed (cleaned) from the VIP before the new information is downloaded from the RP to the VIP.


Related Commands

Command
Description

set ip next-hop verify-availability

Configures policy routing to verify if the next hops of a route map are CDP neighbors before policy routing to that next hop.


show xdr

To display details about eXternal Data Representation (XDR), use the show xdr command in user EXEC or privileged EXEC mode.

show xdr {client {client-name | all} [statistics] | linecard [linecard-number] [internal] | multicast-group | timers}

Syntax Description

client {client-name | all}

Displays client basic information or statistics for a client or all clients.

statistics

(Optional) Displays XDR statistics.

linecard

(Line cards only) (Route/Switch Processor (RSP) on Cisco 7500 series and Route Processor (RP) on Cisco 10000 series) Displays XDR information for all XDR line card peer instances or the specified XDR line card peer instance.

linecard-number

(Optional) Specifies the line card slot number.

internal

(Optional) (RSP only) Displays internal information.

multicast-group

Displays XDR multicast groups.

timers

Displays XDR timers.


Command Default

XDR details are not displayed.

Command Modes

User EXEC (>)
Privileged EXEC (#)

Command History

Release
Modification

12.2(25)S

This command was introduced.

12.2(28)SB

This command was integrated into Cisco IOS Release 12.2(28)SB and implemented on the Cisco 10000 series routers.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.2(33)SXH

This command was integrated into Cisco IOS Release 12.2(33)SXH.

12.4(20)T

This command was integrated into Cisco IOS Release 12.4(20)T.


Usage Guidelines

This command is available only on distributed platforms (such as the Cisco 7500 series) and on the Cisco 10000 series routers.

Examples

The following example shows how to display XDR information for all clients:

Router# show xdr client all

XDR Interrupt P(0) flag:1 decode:0x413B9804 pull:0x413B9AE8 context:8
XDR Process Pri(1) flag:1 decode:0x413B99A0 pull:0x413B9D3C context:6
FIBHWIDB broker(2) flag:1 decode:0x0 pull:0x413A7B7C context:2
FIBIDB broker  (3) flag:1 decode:0x0 pull:0x413A844C context:2
FIBHWIDB Subblo(4) flag:1 decode:0x0 pull:0x413A8E20 context:2
FIBIDB Subblock(5) flag:1 decode:0x0 pull:0x413A97DC context:2
XDR High Queue (6) flag:3 decode:0x4031AFFC pull:0x4031B934 context:1
Adjacency updat(7) flag:1 decode:0x413B266C pull:0x413B261C context:2
XDR Medium Queu(8) flag:3 decode:0x4031B004 pull:0x4031B95C context:1
IPv4 table brok(9) flag:1 decode:0x0 pull:0x413B21F0 context:6
IPv6 table brok(10) flag:1 decode:0x0 pull:0x413ECA90 context:6
XDR Low Queue  (11) flag:3 decode:0x4031B00C pull:0x4031B984 context:1
MFI RP Pull    (12) flag:1 decode:0x0 pull:0x413E1174 context:1
Push Client One(13) flag:1 decode:0x413BA300 pull:0x0 context:4
CEF push       (14) flag:1 decode:0x413A3D74 pull:0x0 context:124
MFI non-RP Push(15) flag:1 decode:0x413DFA34 pull:0x0 context:4
XDR ping       (16) flag:1 decode:0x413BABB4 pull:0x0 context:1

The following example shows how to display XDR information for all XDR line card peer instances:

Router# show xdr linecard

XDR slot number 1, status  PEER UP             
    IPC messages sent 48
    Next sequence number to send     21
    Maximum sequence number expected 36

XDR slot number 2, status  PEER UP             
    IPC messages sent 52
    Next sequence number to send     31
    Maximum sequence number expected 46

XDR slot number 3, status  PEER UP             
    IPC messages sent 55
    Next sequence number to send     17
    Maximum sequence number expected 32

The following example shows how to display XDR information for the XDR line card peer instance in slot number 1:

Router# show xdr linecard 1

XDR slot number 1, status  PEER UP             
    IPC messages sent 48
    Next sequence number to send     21
    Maximum sequence number expected 36

The following example shows how to display internal XDR information for the XDR line card peer instance in slot number 1:

Router# show xdr linecard 1 internal

XDR slot number 1, status  PEER UP             
    IPC messages sent 48
    Next sequence number to send     21
    Maximum sequence number expected 36
                            Tx   bytes         Rx   bytes
    XDR Interrupt Priori:
                             0      0         2391   11955   Window Message
                             21     336       0      0       Time Message
                             2      8         0      0       Resequence Message
                             0      0         1      6       CEF LC state
    XDR Process Priority:
                             0      0         1      3       Registration Signal
                             2      10        0      0       CEF running
    FIBHWIDB broker     :
                             90     33570     0      0       fibhwidb update
    FIBIDB broker       :
                             80     30960     0      0       fibidb update
    FIBIDB Subblock brok:
                             10     315       0      0       fibswsb update
    Adjacency update    :
                             2      6         0      0       Adjacency update me
                             3      9         0      0       Adjacency repopulat
    IPv4 table broker   :
                             16     558       0      0       prefix
                             4      24        0      0       epoch
                             2      36        0      0       table
                             4      44        0      0       multicast prefix
    IPv6 table broker   :
                             1      18        0      0       table
    CEF push            :
                             12     72        19     114     repopulation req
                             0      0         1      12      isl table update rq
                             0      0         1      12      dot1q table updateq
                             2      10        0      0       state
                             9      452       0      0       control
                             1      3         0      0       flow features deace
                             1      22        0      0       flow cache config
                             1      40        0      0       flow export config
                             6      470       0      0       access-list config
                             2      10        0      0       access-list delete
                             1      12        0      0       route-map
                             1      16        0      0       icmp limit
                             1      8         0      0       SSM RP to LC commas
    XDR ping            :
                             3      12        3      12      ping message

The following is sample output from the show xdr multicast-group command:

Router# show xdr multicast-group

0x4300DC00  READY    Window: 15   Linecards: 2
  XDR High Queue  xdrs to push: 0
  XDR Medium Queu xdrs to push: 0
  XDR Low Queue   xdrs to push: 0

0x4414BC60  READY    Window: 15   Linecards: 1
  XDR High Queue  xdrs to push: 0
  XDR Medium Queu xdrs to push: 0
  XDR Low Queue   xdrs to push: 0

0x44159420  READY    Window: 15   Linecards: 3
  XDR High Queue  xdrs to push: 0
  XDR Medium Queu xdrs to push: 0
  XDR Low Queue   xdrs to push: 0

The following is sample output from the show xdr timers command:

Router# show xdr timers

XDR multicast timers
    Expiration    Type
|        0.000  (parent)

XDR RP ping timers
    Expiration    Type
|        0.000  (parent)

XDR RP timers
    Expiration    Type
|     1:19.236  (parent)
  |     1:19.236   Sending Time
  |     4:59.236   Keepalive timer slot: 2
  |     4:59.236   Keepalive timer slot: 1
  |     4:59.248   Keepalive timer slot: 3

Cisco 10000 Series Router Examples

The following example shows how to display XDR information for all clients:

Router# show xdr client all

XDR Interrupt P(0) flag:RP|ISSU aware
  ISSU capable slot(s): 1 
XDR Process Pri(1) flag:RP|ISSU aware
  ISSU capable slot(s): 1 
FIBHWIDB broker(2) flag:RP|ISSU aware
  ISSU capable slot(s): 1
FIBIDB broker  (3) flag:RP|ISSU aware
  ISSU capable slot(s): 1 
FIBHWIDB Subblo(4) flag:RP|ISSU aware
  ISSU capable slot(s): 1 
FIBIDB Subblock(5) flag:RP|ISSU aware
  ISSU capable slot(s): 1 
XDR High Queue (6) flag:RP|LC
Adjacency updat(7) flag:RP|ISSU aware
  ISSU capable slot(s): 1 
XDR Medium Queu(8) flag:RP|LC
IPv4 table brok(9) flag:RP|ISSU aware
  ISSU capable slot(s): 1 
XDR Low Queue  (11) flag:RP|LC
MFI Pull       (12) flag:RP|ISSU aware
  ISSU capable slot(s): 1 
Push Client One(13) flag:RP
CEF push       (14) flag:RP|ISSU aware
  ISSU capable slot(s): 1 
MFI Push       (15) flag:RP|ISSU aware
  ISSU capable slot(s): 1 
XDR ping       (16) flag:RP
MPLS Embedded M(17) flag:RP

The following example shows how to display XDR information for all XDR line card peer instances:

Router# show xdr linecard

XDR slot number 1, status  PEER UP                       
    IPC messages sent 569
    This is the secondary RP
    Next sequence number to send     116
    Maximum sequence number expected 160
    ISSU state: Nego done, version 2, mtu 7, sid 31

The following example shows how to display XDR information for the XDR line card peer instance in slot number 1:

Router# show xdr linecard 1

XDR slot number 1, status  PEER UP                       
    IPC messages sent 570
    This is the secondary RP
    Next sequence number to send     116
    Maximum sequence number expected 160
    ISSU state: Nego done, version 2, mtu 7, sid 31

The following example shows how to display internal XDR information for the XDR line card peer instance in slot number 1:

Router# show xdr linecard 1 internal

XDR slot number 1, status  PEER UP                       
    IPC maximum mtu   1478
    IPC messages sent 570
    This is the secondary RP
    Next sequence number to send     116
    Maximum sequence number expected 160
    ISSU state: Nego done, version 2, mtu 7, sid 31
                            Tx   bytes         Rx   bytes
    XDR Interrupt Priori:
                             0      0         10427  52135   Window Message
                             87     1392      0      0       Time Message
                             1      4         0      0       Resequence Message
                             19     444       11     264     ISSU nego
    XDR Process Priority:
                             17     51        11     33      Reg Signal
                             1      2         0      0       CEF running
                             0      0         1      4       CEF reload request
                             15     348       9      216     ISSU nego
    FIBHWIDB broker     :
                             32     3588      0      0       fibhwidb update
                             7      156       5      120     ISSU nego
    FIBIDB broker       :
                             49     6429      0      0       fibidb update
                             7      156       5      120     ISSU nego
    FIBHWIDB Subblock br:
                             7      156       5      120     ISSU nego
    FIBIDB Subblock brok:
                             41     1533      0      0       fibswsb update
                             13     300       8      192     ISSU nego
    Adjacency update    :
                             62     3089      0      0       adj update
                             4      8         0      0       adj epoch
                             17     396       10     240     ISSU nego
    IPv4 table broker   :
                             285    28557     0      0       prefix
                             8      48        0      0       epoch
                             5      78        0      0       table
                             5      55        0      0       multicast prefix
                             45     1068      24     576     ISSU nego
    MFI Pull            :
                             12     456       0      0       pull update
                             75     1788      39     936     ISSU nego
    CEF push            :
                             8      48        14     84      repopulation req
                             5      10        0      0       state
                             12     816       0      0       control
                             2      0         0      0       mpls_access-list delete
                             2      32        0      0       icmp limit
                             9      204       6      144     ISSU nego
    MFI Push            :
                             3      101       0      0       service reply
                             2      34        0      0       client request
                             0      0         4      106     service request
                             2      16        0      0       enable/redist redistribution
client
                             153    3660      78     1872    ISSU nego
    XDR ping            :
                             6      24        6      24      ping message

Related Commands

Command
Description

show cef broker

Displays Cisco Express Forwarding information related to a selected update broker.


snmp mib cef throttling-interval

To set the throttling interval for the CEF-MIB inconsistency notifications, use the snmp mib cef throttling-interval command in global configuration mode. To remove the throttling interval, use the no form of this command.

snmp mib cef throttling-interval seconds

no snmp mib cef throttling-interval seconds

Syntax Description

seconds

The time to allow before an inconsistency notification is sent during the process of updating forwarding information from the Routing Information Base (RIB) to the Route Processor (RP) and the line card databases. The valid values are from 0 to 3600 seconds.


Command Default

Throttling is disabled by default (throttling interval is set to 0 seconds).

Command Modes

Global configuration (config)

Command History

Release
Modification

12.2(31)SB

This command was introduced.

12.2(33)SRC

This command was integrated into Cisco IOS Release 12.2(33)SRC.

12.2(33)SB

This command was integrated into Cisco IOS Release 12.2(33)SB.

12.4(20)T

This command was integrated into Cisco IOS Release 12.4(20)T.

15.0(1)M

This command was integrated into Cisco IOS Release 15.0(1)M.

12.2(33)SRE

This command was integrated into Cisco IOS Release 12.2(33)SRE.

12.2(50)SY

This command was integrated into Cisco IOS Release 12.2(50)SY.


Usage Guidelines

Use this command in conjunction with the snmp-server enable traps cef inconsistency command to set the time that elapsed between the occurrence of a Cisco Express Forwarding database inconsistencies and the time when you want to receive an inconsistency notification.

If you set the throttling interval to 0 seconds, throttling is disabled.

Examples

The following example shows how to set the throttling interval for CEF-MIB inconsistency notification to 300 seconds:

configure terminal 
!
snmp-server enable traps cef inconsistency
snmp mib cef throttling-interval 300

Related Commands

Command
Description

snmp-server enable traps cef

Enables CEF-MIB notifications that correspond to Cisco Express Forwarding events.

snmp-server host

Specifies the recipient of an SNMP notification operation.


snmp-server enable traps cef

To enable Cisco Express Forwarding support of Simple Network Management Protocol (SNMP) notifications on a network management system (NMS), use the snmp-server enable traps cef command in global configuration mode. To disable Cisco Express Forwarding support of SNMP notifications, use the no form of this command.

snmp-server enable traps cef [peer-state-change] [resource-failure] [inconsistency] [peer-fib-state-change]

no snmp-server enable traps cef [peer-state-change] [resource-failure] [inconsistency] [peer-fib-state-change]

Syntax Description

peer-state-change

(Optional) Enables the sending of CEF-MIB SNMP notifications for changes in the operational state of Cisco Express Forwarding peers.

resource-failure

(Optional) Enables the sending of CEF-MIB SNMP notifications for resource failures that affect Cisco Express Forwarding operations.

inconsistency

(Optional) Enables the sending of CEF-MIB SNMP notifications for inconsistencies that occur when routing information is updated from the Routing Information Base (RIB) to the Cisco Express Forwarding Forwarding Information Base (FIB) on the Route Processor (RP) and to the Cisco Express Forwarding FIB on the line cards.

peer-fib-state-change

(Optional) Enables the sending of CEF-MIB SNMP notifications for changes in the operational state of the Cisco Express Forwarding peer FIB.


Command Default

All CEF-MIB notifications are disabled by default.

Command Modes

Global configuration (config)

Command History

Release
Modification

12.2(31)SB2

This command was introduced.

12.2(33)SRC

This command was integrated into Cisco IOS Release 12.2(33)SRC.

12.2(33)SB

This command was integrated into Cisco IOS Release 12.2(33)SB.

12.4(20)T

This command was integrated into Cisco IOS Release 12.4(20)T.

15.0(1)M

This command was integrated into Cisco IOS Release 15.0(1)M.

12.2(33)SRE

This command was integrated into Cisco IOS Release 12.2(33)SRE.

12.2(50)SY

This command was integrated into Cisco IOS Release 12.2(50)SY.


Usage Guidelines

You can use this command to enable CEF-MIB SNMP notifications that correspond to specific Cisco Express Forwarding events. To send the notifications to an NMS or host system, you must configure the snmp-server host command with the cef keyword.

You can enable all CEF-MIB SNMP notifications if you enter the snmp-server enable traps cef command without entering an optional keyword.

Examples

The following example shows how to enable a router to send Cisco Express Forwarding peer state changes and forwarding inconsistencies as informs to the NMS with IP address 10.56.125.47 and to use the community string defined as public:

configure terminal
!
snmp-server enable traps cef peer-state-change inconsistency
snmp-server host 10.56.125.47 informs version 2c public

Related Commands

Command
Description

snmp-server community

Configures a community access string to permit SNMP access to the local router by the remote SNMP software client.

snmp-server host

Specifies the recipient of an SNMP notification operation.


snmp-server host

To specify the recipient of a Simple Network Management Protocol (SNMP) notification operation, use the snmp-server host command in global configuration mode. To remove the specified host from the configuration, use the no form of this command.

snmp-server host {hostname | ip-address} [vrf vrf-name] [informs | traps] [version {1 | 2c | 3 [auth | noauth | priv]}] community-string [udp-port port] [notification-type]

no snmp-server host {hostname | ip-address} [vrf vrf-name] [informs | traps] [version {1 | 2c | 3 [auth | noauth | priv]}] community-string [udp-port port] [notification-type]

Command Syntax on Cisco ME 3400, ME 3400E, and Catalyst 3750 Metro Switches

snmp-server host ip-address {community-string | {informs | traps} {community-string |
version {1 | 2c | 3 {auth | noauth}} community-string | version {1 | 2c | 3 {auth | noauth}} community-string | vrf vrf-name {informs | traps} {community-string | version {1 | 2c | 3 {auth | noauth}} community-string}} [notification-type]

no snmp-server host ip-address {community-string | {informs | traps} {community-string |
version {1 | 2c | 3 {auth | noauth}} community-string | version {1 | 2c | 3 {auth | noauth}} community-string | vrf vrf-name {informs | traps} {community-string | version {1 | 2c | 3 {auth | noauth}} community-string}} [notification-type]

Command Syntax on Cisco 7600 Series Router

snmp-server host ip-address {community-string | {informs | traps} {community-string |
version {1 | 2c | 3 {auth | noauth | priv}} community-string | version {1 | 2c | 3 {auth | noauth | priv}} community-string | vrf vrf-name {informs | traps} {community-string | version {1 | 2c | 3 {auth | noauth | priv}} community-string}} [notification-type]

no snmp-server host ip-address {community-string | {informs | traps} {community-string |
version {1 | 2c | 3 {auth | noauth | priv}} community-string | version {1 | 2c | 3 {auth | noauth | priv}} community-string | vrf vrf-name {informs | traps} {community-string | version {1 | 2c | 3 {auth | noauth | priv}} community-string}} [notification-type]

Syntax Description

hostname

Name of the host. The SNMP notification host is typically a network management station (NMS) or SNMP manager. This host is the recipient of the SNMP traps or informs.

ip-address

IPv4 address or IPv6 address of the SNMP notification host.

vrf

(Optional) Specifies that a Virtual Private Network (VPN) routing and forwarding (VRF) instance should be used to send SNMP notifications.

In Cisco IOS Release 12.2(54)SE, the vrf keyword is required.

vrf-name

(Optional) VPN VRF instance used to send SNMP notifications.

In Cisco IOS Release 12.2(54)SE, the vrf-name argument is required.

informs

(Optional) Specifies that notifications should be sent as informs.

In Cisco IOS Release 12.2(54)SE, the informs keyword is required.

traps

(Optional) Specifies that notifications should be sent as traps. This is the default.

In Cisco IOS Release 12.2(54)SE, the traps keyword is required.

version

(Optional) Specifies the version of the SNMP that is used to send the traps or informs. The default is 1.

In Cisco IOS Release 12.2(54)SE, the version keyword is required and the priv keyword is not supported.

If you use the version keyword, one of the following keywords must be specified:

1—SNMPv1.

2c—SNMPv2C.

3—SNMPv3. The most secure model because it allows packet encryption with the priv keyword. The default is noauth.

One of the following three optional security level keywords can follow the 3 keyword:

auth—Enables message digest algorithm 5 (MD5) and Secure Hash Algorithm (SHA) packet authentication.

noauth—Specifies that the noAuthNoPriv security level applies to this host. This is the default security level for SNMPv3.

priv—Enables Data Encryption Standard (DES) packet encryption (also called "privacy").

community-string

Password-like community string sent with the notification operation.

Note You can set this string using the snmp-server host command by itself, but Cisco recommends that you define the string using the snmp-server community command prior to using the snmp-server host command.

Note The "at" sign (@) is used for delimiting the context information.

udp-port

(Optional) Specifies that SNMP traps or informs are to be sent to an NMS host.

In Cisco IOS Release 12.2(54)SE, the udp-port keyword is not supported.

port

(Optional) User Datagram Protocol (UDP) port number of the NMS host. The default is 162.

In Cisco IOS Release 12.2(54)SE, the port argument is not supported.

notification-type

(Optional) Type of notification to be sent to the host. If no type is specified, all available notifications are sent. See the "Notification-Type Keywords" section in the "Usage Guidelines" section for more information about the keywords available.


Command Default

This command behavior is disabled by default. A recipient is not specified to receive notifications.

Command Modes

Global configuration (config)

Command History

Release
Modification

10.0

This command was introduced.

Cisco IOS Release 12 Mainline/T Train

12.0(3)T

The version 3 [auth | noauth | priv] syntax was added as part of the SNMPv3 Support feature.

The hsrp notification-type keyword was added.

The voice notification-type keyword was added.

12.1(3)T

The calltracker notification-type keyword was added for the Cisco AS5300 and AS5800 platforms.

12.2(2)T

The vrf vrf-name keyword and argument combination was added.

The ipmobile notification-type keyword was added.

Support for the vsimaster notification-type keyword was added for the Cisco 7200 and Cisco 7500 series.

12.2(4)T

The pim notification-type keyword was added.

The ipsec notification-type keyword was added.

12.2(8)T

The mpls-traffic-eng notification-type keyword was added.

The director notification-type keyword was added.

12.2(13)T

The srp notification-type keyword was added.

The mpls-ldp notification-type keyword was added.

12.3(2)T

The flash notification-type keyword was added.

The l2tun-session notification-type keyword was added.

12.3(4)T

The cpu notification-type keyword was added.

The memory notification-type keyword was added.

The ospf notification-type keyword was added.

12.3(8)T

The iplocalpool notification-type keyword was added for the Cisco 7200 and 7301 series routers.

12.3(11)T

The vrrp keyword was added.

12.3(14)T

Support for SNMP over IPv6 transport was integrated into Cisco IOS Release 12.3(14)T. Either an IP or IPv6 Internet address can be specified as the hostname argument.

The eigrp notification-type keyword was added.

12.4(20)T

The license notification-type keyword was added.

15.0(1)M

The nhrp notification-type keyword was added.

The automatic insertion of the snmp-server community command into the configuration, along with the community string specified in the snmp-server host command, was changed. The snmp-server community command must be manually configured.

Cisco IOS Release 12.0S

12.0(17)ST

The mpls-traffic-eng notification-type keyword was added.

12.0(21)ST

The mpls-ldp notification-type keyword was added.

12.0(22)S

All features in Cisco IOS Release 12.0ST were integrated into Cisco IOS Release 12.0(22)S.

The mpls-vpn notification-type keyword was added.

12.0(23)S

The l2tun-session notification-type keyword was added.

12.0(26)S

The memory notification-type keyword was added.

12.0(27)S

Support for SNMP over IPv6 transport was added. Either an IP or IPv6 Internet address can be specified as the hostname argument.

The vrf vrf-name keyword and argument combination was added to support multiple Lightweight Directory Protocol (LDP) contexts for VPNs.

12.0(31)S

The l2tun-pseudowire-status notification-type keyword was added.

Release 12.2S
 

12.2(18)S

This command was integrated into Cisco IOS Release 12.2(18)S.

12.2(25)S

The cpu notification-type keyword was added.

The memory notification-type keyword was added.

12.2(28)SB

This command was integrated into Cisco IOS Release 12.2(28)SB.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.2(31)SB2

The cef notification-type keyword was added.

12.2(33)SXH

This command was integrated into Cisco IOS Release 12.2(33)SXH.

12.2(33)SB

This command was integrated into Cisco IOS Release 12.2(33)SB.

12.2(33)SXI5

The dhcp-snooping notification-type keyword was added.

The errdisable notification-type keyword was added.

12.2(54)SE

This command was modified. See the "Command Syntax on Cisco ME 3400, ME 3400E, and Catalyst 3750 Metro Switches" section for the command syntax for these switches.

12.2(33)SXJ

This command was integrated into Cisco IOS Release 12.2(33)SXJ. The public storm-control notification-type keyword was added.

12.2(50)SY

This command integrated into Cisco IOS Release 12.2(50)SY.

Cisco IOS Release 15S
 

15.0(1)S

This command was modified. The flowmon notification-type keyword was added.

Cisco IOS XE
 

Cisco IOS XE Release 2.1

This command was integrated into Cisco IOS XE Release 2.1.


Usage Guidelines

If you enter this command with no optional keywords, the default is to send all notification-type traps to the host. No informs will be sent to the host.

The no snmp-server host command with no keywords disables traps, but not informs, to the host. To disable informs, use the no snmp-server host informs command.


Note If a community string is not defined using the snmp-server community command prior to using this command, the default form of the snmp-server community command will automatically be inserted into the configuration. The password (community string) used for this automatic configuration of the snmp-server community will be the same as that specified in the snmp-server host command. This automatic command insertion and use of passwords is the default behavior for Cisco IOS Release 12.0(3) and later releases.


SNMP notifications can be sent as traps or inform requests. Traps are unreliable because the receiver does not send acknowledgments when it receives traps. The sender cannot determine if the traps were received. However, an SNMP entity that receives an inform request acknowledges the message with an SNMP response protocol data unit (PDU). If the sender never receives the response, the inform request can be sent again. Thus, informs are more likely than traps to reach their intended destination.

Compared to traps, informs consume more resources in the agent and in the network. Unlike a trap, which is discarded as soon as it is sent, an inform request must be held in memory until a response is received or the request times out. Also, traps are sent only once; an inform may be tried several times. The retries increase traffic and contribute to a higher overhead on the network.

If you do not enter an snmp-server host command, no notifications are sent. To configure the router to send SNMP notifications, you must enter at least one snmp-server host command. If you enter the command with no optional keywords, all trap types are enabled for the host.

To enable multiple hosts, you must issue a separate snmp-server host command for each host. You can specify multiple notification types in the command for each host.

When multiple snmp-server host commands are given for the same host and kind of notification (trap or inform), each succeeding command overwrites the previous command. Only the last snmp-server host command will be in effect. For example, if you enter an snmp-server host inform command for a host and then enter another snmp-server host inform command for the same host, the second command will replace the first.

The snmp-server host command is used in conjunction with the snmp-server enable command. Use the snmp-server enable command to specify which SNMP notifications are sent globally. For a host to receive most notifications, at least one snmp-server enable command and the snmp-server host command for that host must be enabled.

Some notification types cannot be controlled with the snmp-server enable command. Some notification types are always enabled, and others are enabled by a different command. For example, the linkUpDown notifications are controlled by the snmp trap link-status command. These notification types do not require an snmp-server enable command.

The availability of a notification-type options depends on the router type and the Cisco IOS software features supported on the router. For example, the envmon notification type is available only if the environmental monitor is part of the system. To see what notification types are available on your system, use the command help ? at the end of the snmp-server host command.

The vrf keyword allows you to specify the notifications being sent to a specified IP address over a specific virtual routing and forwarding (VRF) VPN. The VRF defines a VPN membership of a user so that data is stored using the VPN.

In the case of the NMS sending the query having a correct SNMP community but that does not have a read or a write view, the SNMP agent returns the following error values:

For a get or a getnext query, returns GEN_ERROR for SNMPv1 and AUTHORIZATION_ERROR for SNMPv2C.

For a set query, returns NO_ACCESS_ERROR.

Notification-Type Keywords

The notification type can be one or more of the following keywords:


Note The available notification types differ based on the platform and Cisco IOS release. For a complete list of available notification types, use the question mark (?) online help function.


aaa server—Sends SNMP authentication, authorization, and accounting (AAA) traps.

adslline—Sends Asymmetric Digital Subscriber Line (ADSL) LINE-MIB traps.

atm—Sends ATM notifications.

authenticate-fail—Sends an SNMP 802.11 Authentication Fail trap.

auth-framework—Sends SNMP CISCO-AUTH-FRAMEWORK-MIB notifications.

bgp—Sends Border Gateway Protocol (BGP) state change notifications.

bridge—Sends SNMP STP Bridge MIB notifications.

bstun—Sends Block Serial Tunneling (bstun) event notifications.

bulkstat—Sends Data-Collection-MIB notifications.

c6kxbar—Sends SNMP crossbar notifications.

callhome—Sends Call Home MIB notifications.

calltracker—Sends Call Tracker call-start/call-end notifications.

casa—Sends Cisco Appliances Services Architecture (CASA) event notifications.

ccme—Sends SNMP Cisco netManager Event (CCME) traps.

cef—Sends notifications related to Cisco Express Forwarding.

chassis—Sends SNMP chassis notifications.

cnpd—Sends Cisco network-based application recognition (NBAR) Protocol Discovery (CNPD) traps.

config—Sends configuration change notifications.

config-copy—Sends SNMP config-copy notifications.

config-ctid—Sends SNMP config-ctid notifications.

cpu—Sends CPU-related notifications.

csg—Sends SNMP Content Services Gateway (CSG) notifications.

deauthenticate—Sends an SNMP 802.11 Deauthentication trap.

dhcp-snooping—Sends Dynamic Host Configuration Protocol (DHCP) snooping MIB notifications.

director—Sends notifications related to DistributedDirector.

disassociate—Sends an SNMP 802.11 Disassociation trap.

dlsw—Sends data-link switching (DLSW) notifications.

dnis—Sends SNMP Dialed Number Identification Service (DNIS) traps.

dot1x—Sends 802.1X notifications.

dot11-mibs—Sends dot11 traps.

dot11-qos—Sends SNMP 802.11 QoS Change trap.

ds1—Sends SNMP digital signaling 1 (DS1) notifications.

ds1-loopback—Sends ds1-loopback traps.

dspu—Sends downstream physical unit (DSPU) notifications.

eigrp—Sends Enhanced Interior Gateway Routing Protocol (EIGRP) stuck-in-active (SIA) and neighbor authentication failure notifications.

energywise—Sends SNMP energywise notifications.

entity—Sends Entity MIB modification notifications.

entity-diag—Sends SNMP entity diagnostic MIB notifications.

envmon—Sends Cisco enterprise-specific environmental monitor notifications when an environmental threshold is exceeded.

errdisable—Sends error disable notifications.

ethernet-cfm—Sends SNMP Ethernet Connectivity Fault Management (CFM) notifications.

event-manager—Sends SNMP Embedded Event Manager notifications.

firewall—Sends SNMP Firewall traps.

flash—Sends flash media insertion and removal notifications.

flexlinks—Sends FLEX links notifications.

flowmon—Sends flow monitoring notifications.

frame-relay—Sends Frame Relay notifications.

fru-ctrl—Sends entity field-replaceable unit (FRU) control notifications.

hsrp—Sends Hot Standby Routing Protocol (HSRP) notifications.

icsudsu—Sends SNMP ICSUDSU traps.

iplocalpool—Sends IP local pool notifications.

ipmobile—Sends Mobile IP notifications.

ipmulticast—Sends IP multicast notifications.

ipsec—Sends IP Security (IPsec) notifications.

isakmp—Sends SNMP ISAKMP notifications.

isdn—Sends ISDN notifications.

l2tc—Sends SNMP L2 tunnel configuration notifications.

l2tun-pseudowire-status—Sends pseudowire state change notifications.

l2tun-session—Sends Layer 2 tunneling session notifications.

license—Sends licensing notifications as traps or informs.

llc2—Sends Logical Link Control, type 2 (LLC2) notifications.

mac-notification—Sends SNMP MAC notifications.

memory—Sends memory pool and memory buffer pool notifications.

module—Sends SNMP module notifications.

module-auto-shutdown—Sends SNMP module autoshutdown MIB notifications.

mpls-fast-reroute—Sends SNMP Multiprotocol Label Switching (MPLS) traffic engineering fast reroute notifications.

mpls-ldp—Sends MPLS Label Distribution Protocol (LDP) notifications indicating status changes in LDP sessions.

mpls-traffic-eng—Sends MPLS traffic engineering notifications indicating changes in the status of MPLS traffic engineering tunnels.

mpls-vpn—Sends MPLS VPN notifications.

msdp—Sends SNMP Multicast Source Discovery Protocol (MSDP) notifications.

mvpn—Sends multicast VPN notifications.

nhrp—Sends Next Hop Resolution Protocol (NHRP) notifications.

ospf—Sends Open Shortest Path First (OSPF) sham-link notifications.

pim—Sends Protocol Independent Multicast (PIM) notifications.

port-security—Sends SNMP port-security notifications.

power-ethernet—Sends SNMP power Ethernet notifications.

public storm-control—Sends SNMP public storm-control notifications.

pw-vc—Sends SNMP pseudowire virtual circuit (VC) notifications.

repeater—Sends standard repeater (hub) notifications.

resource-policy—Sends CISCO-ERM-MIB notifications.

rf—Sends SNMP RF MIB notifications.

rogue-ap—Sends an SNMP 802.11 Rogue AP trap.

rsrb—Sends remote source-route bridging (RSRB) notifications.

rsvp—Sends Resource Reservation Protocol (RSVP) notifications.

rtr—Sends Response Time Reporter (RTR) notifications.

sdlc—Sends Synchronous Data Link Control (SDLC) notifications.

sdllc—Sends SDLC Logical Link Control (SDLLC) notifications.

slb—Sends SNMP server load balancer (SLB) notifications.

snmp—Sends any enabled RFC 1157 SNMP linkUp, linkDown, authenticationFailure, warmStart, and coldStart notifications.


Note To enable RFC 2233-compliant link up/down notifications, you should use the snmp server link trap command.


sonet—Sends SNMP SONET notifications.

srp—Sends Spatial Reuse Protocol (SRP) notifications.

stpx—Sends SNMP STPX MIB notifications.

srst—Sends SNMP Survivable Remote Site Telephony (SRST) traps.

stun—Sends serial tunnel (STUN) notifications.

switch-over—Sends an SNMP 802.11 Standby Switch-over trap.

syslog—Sends error message notifications (Cisco Syslog MIB). Use the logging history level command to specify the level of messages to be sent.

syslog—Sends error message notifications (Cisco Syslog MIB). Use the logging history level command to specify the level of messages to be sent.

tty—Sends Cisco enterprise-specific notifications when a TCP connection closes.

udp-port—Sends the notification host's UDP port number.

vlan-mac-limit—Sends SNMP L2 control VLAN MAC limit notifications.

vlancreate—Sends SNMP VLAN created notifications.

vlandelete—Sends SNMP VLAN deleted notifications.

voice—Sends SNMP voice traps.

vrrp—Sends Virtual Router Redundancy Protocol (VRRP) notifications.

vsimaster—Sends Virtual Switch Interface (VSI) Master notifications.

vswitch—Sends SNMP virtual switch notifications.

vtp—Sends SNMP VLAN Trunking Protocol (VTP) notifications.

wlan-wep—Sends an SNMP 802.11 Wireless LAN (WLAN) Wired Equivalent Privacy (WEP) trap.

x25—Sends X.25 event notifications.

xgcp—Sends External Media Gateway Control Protocol (XGCP) traps.

SNMP-Related Notification-Type Keywords

The notification-type keywords used in the snmp-server host command do not always match the keywords used in the corresponding snmp-server enable traps command. For example, the notification keyword applicable to Multiprotocol Label Switching Protocol (MPLS) traffic engineering tunnels is specified as mpls-traffic-eng (containing two hyphens and no embedded spaces). The corresponding parameter in the snmp-server enable traps command is specified as mpls traffic-eng (containing an embedded space and a hyphen).

This syntax difference is necessary to ensure that the CLI interprets the notification-type keyword of the snmp-server host command as a unified, single-word construct, which preserves the capability of the snmp-server host command to accept multiple notification-type keywords in the command line. The snmp-server enable traps commands, however, often use two-word constructs to provide hierarchical configuration options and to maintain consistency with the command syntax of related commands. Table 97 maps some examples of snmp-server enable traps commands to the keywords used in the snmp-server host command.

Table 97 SNMP-server enable traps Commands and Corresponding Notification Keywords

snmp-server enable traps Command
snmp-server host Command Keyword

snmp-server enable traps l2tun session

l2tun-session

snmp-server enable traps mpls ldp

mpls-ldp

snmp-server enable traps mpls traffic-eng1

mpls-traffic-eng

snmp-server enable traps mpls vpn

mpls-vpn

1 See the Cisco IOS Multiprotocol Label Switching Command Reference for documentation of this command.


Examples

If you want to configure a unique SNMP community string for traps but prevent SNMP polling access with this string, the configuration should include an access list. The following example shows how to name a community string comaccess and number an access list 10:

Router(config)# snmp-server community comaccess ro 10 
Router(config)# snmp-server host 192.20.2.160 comaccess 
Router(config)# access-list 10 deny any 


Note The "at" sign (@) is used as a delimiter between the community string and the context in which it is used. For example, specific VLAN information in BRIDGE-MIB may be polled using community@VLAN-ID (for example, public@100), where 100 is the VLAN number.


The following example shows how to send RFC 1157 SNMP traps to a specified host named myhost.cisco.com. Other traps are enabled, but only SNMP traps are sent because only snmp is specified in the snmp-server host command. The community string is defined as comaccess.

Router(config)# snmp-server enable traps
Router(config)# snmp-server host myhost.cisco.com comaccess snmp 

The following example shows how to send the SNMP and Cisco environmental monitor enterprise-specific traps to address 192.30.2.160 using the community string public:

Router(config)# snmp-server enable traps snmp 
Router(config)# snmp-server enable traps envmon 
Router(config)# snmp-server host 192.30.2.160 public snmp envmon 

The following example shows how to enable the router to send all traps to the host myhost.cisco.com using the community string public:

Router(config)# snmp-server enable traps 
Router(config)# snmp-server host myhost.cisco.com public 

The following example will not send traps to any host. The BGP traps are enabled for all hosts, but only the ISDN traps are enabled to be sent to a host. The community string is defined as public.

Router(config)# snmp-server enable traps bgp
Router(config)# snmp-server host myhost.cisco.com public isdn

The following example shows how to enable the router to send all inform requests to the host myhost.cisco.com using the community string public:

Router(config)# snmp-server enable traps 
Router(config)# snmp-server host myhost.cisco.com informs version 2c public 

The following example shows how to send HSRP MIB informs to the host specified by the name myhost.cisco.com. The community string is defined as public.

Router(config)# snmp-server enable traps hsrp
Router(config)# snmp-server host myhost.cisco.com informs version 2c public hsrp

The following example shows how to send all SNMP notifications to example.com over the VRF named trap-vrf using the community string public:

Router(config)# snmp-server host example.com vrf trap-vrf public

The following example shows how to configure an IPv6 SNMP notification server with the IPv6 address 2001:0DB8:0000:ABCD:1 using the community string public:

Router(config)# snmp-server host 2001:0DB8:0000:ABCD:1 version 2c public udp-port 2012

The following example shows how to specify VRRP as the protocol using the community string public:

Router(config)# snmp-server enable traps vrrp
Router(config)# snmp-server host myhost.cisco.com traps version 2c public vrrp

The following example shows how to send all Cisco Express Forwarding informs to the notification receiver with the IP address 192.40.3.130 using the community string public:

Router(config)# snmp-server enable traps cef
Router(config)# snmp-server host 192.40.3.130 informs version 2c public cef

The following example shows how to enable all NHRP traps, and how to send all NHRP traps to the notification receiver with the IP address 192.40.3.130 using the community string public:

Router(config)# snmp-server enable traps nhrp
Router(config)# snmp-server host 192.40.3.130 traps version 2c public nhrp

Related Commands

Command
Description

show snmp host

Displays recipient details configured for SNMP notifications.

snmp-server enable peer-trap poor qov

Enables poor quality of voice notifications for applicable calls associated with a specific voice dial peer.

snmp-server enable traps

Enables SNMP notifications (traps and informs).

snmp-server enable traps nhrp

Enables SNMP notifications (traps) for NHRP.

snmp-server informs

Specifies inform request options.

snmp-server link trap

Enables linkUp/linkDown SNMP trap that are compliant with RFC 2233.

snmp-server trap-source

Specifies the interface from which an SNMP trap should originate.

snmp-server trap-timeout

Defines how often to try resending trap messages on the retransmission queue.

test snmp trap storm-control event-rev1

Tests SNMP storm-control traps.


switchover pxf restart

To configure the number of parallel express forwarding (PXF) restarts that are allowed before a switchover to a redundant Performance Routing Engine (PRE) module, use the switchover pxf restart command in redundancy configuration (main-cpu) mode. To disable switchovers due to PXF restarts, use the no form of this command.

switchover pxf restart number-of-restarts time-period

no switchover pxf restart

Syntax Description

number-of-restarts

The number of PXF restarts that are allowed within the specified time period. If the PXF processors restart this many times within the given time period, the router switches over to the redundant PRE module. The valid range is 1 to 25. The default is 2 PXF restarts within 5 hours.

time-period

Time period, in hours, that PXF restart counts are monitored. The valid range is 0 to 120 hours.

Note A value of 0 specifies that a switchover occurs on the configured number-of-restarts regardless of the time period.


Command Default

If this command is not configured, the default is 2 PXF restarts within 5 hours.

Command Modes

Redundancy configuration, main-cpu mode (config-r-mc)

Command History

Release
Modification

12.2(15)BC2

This command was introduced on the Cisco uBR10012 router.

12.3(7)

This command was introduced on the Cisco 10000 series router and integrated into Cisco IOS Release 12.3(7).

12.2SB

This command was integrated into Cisco IOS Release 12.2SB.


Usage Guidelines

The startup and running configurations of the standby PRE are synchronized with the active PRE, ensuring the fastest possible cut-over time if the active PRE fails. A second switchover is prevented for 2 hours if a PXF restart occurs on the new active PRE.

A PXF restart following a PXF fault may restore service more quickly when the features in use are not configured for nonstop forwarding with stateful switchover (NSF/SSO), or when SSO mode is not configured on the router. Conversely, a PRE switchover in response to a PXF restart may restore service more quickly when NSF/SSO is configured on the router and all configured features support NSF/SSO.

When a switchover occurs because of repeated PXF restarts, the router displays the following system message:

C10KEVENTMGR-3-PXF_FAIL_SWITCHOVER: Multiple PXF failures, switchover to redundant PRE 
initiated. 

Examples

The following example shows how to configure the router so that if five PXF restarts occur within a one-hour period, the router initiates a switchover to the redundant PRE module.


Router(config)# redundancy
Router(config-red)# main-cpu
Router(config-r-mc)# switchover pxf restart 5 1

Related Commands

Command
Description

main-cpu

Enters main-cpu redundancy configuration mode to configure the synchronization of the active and standby PRE modules.

redundancy

Configures the synchronization of system files between the active and standby PRE modules.

redundancy force-failover main-cpu

Forces a manual switchover between the active and standby PRE modules.

show redundancy

Displays the current redundancy status.


test cef table consistency

To test the Cisco Express Forwarding Forwarding Information Base (FIB) for prefix consistency, use the test cef table consistency command in privilege EXEC mode.

test cef table consistency [detail]

Syntax Description

detail

(Optional) Displays detailed information about the consistency of prefixes in the Cisco Express Forwarding FIB table.


Command Modes

Privileged EXEC (#)

Command History

Release
Modification

12.2(25)S

This command was introduced. This command replaces the show ip cef inconsistency command.

12.2(28)SB

This command was integrated into Cisco IOS Release 12.2(28)SB.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.2(33)SXH

This command was integrated into Cisco IOS Release 12.2(33)SXH.

12.4(20)T

This command was integrated into Cisco IOS Release 12.4(20)T.


Usage Guidelines

This command displays recorded Cisco Express Forwarding consistency records found by the lc-detect, scan-rib-ios, scan-ios-rib, scan-lc-rp, and scan-rp-lc detection mechanisms. The scan-lc-rp and scan-rp-lc detection mechanisms are available only on routers with line cards.

You can configure the Cisco Express Forwarding prefix consistency-detection mechanisms using the cef table consistency-check command.

Examples

The following is sample output from the test cef table consistency command:

Router# test cef table consistency

full-scan-rib-ios: Checking IPv4 RIB to FIB consistency
full-scan-ios-rib: Checking IPv4 FIB to RIB consistency
No IPv4 inconsistencies found, check took 00:00:00.000

The following is sample output from the test cef table consistency detail command:

Router# test cef table consistency detail 

full-scan-rib-ios: Checking IPv4 RIB to FIB consistency
full-scan-rib-ios: FIB checked 12 prefixes, and found 0 missing.
full-scan-ios-rib: Checking IPv4 FIB to RIB consistency
full-scan-ios-rib: Checked 12 FIB prefixes in 1 pass, and found 0 extra.
full-scan-rp-lc: Sent 26 IPv4 prefixes to linecards in 1 pass
full-scan-rp-lc: Initiated IPv4 FIB check on linecards..4..1..0..
full-scan-rp-lc: FIB IPv4 check completed on linecards..1..0..4..
full-scan-rp-lc: Linecard 4 checked 26 IPv4 prefixes (ignored 0). 0 inconsistent.
full-scan-rp-lc: Linecard 1 checked 26 IPv4 prefixes (ignored 0). 0 inconsistent.
full-scan-rp-lc: Linecard 0 checked 26 IPv4 prefixes (ignored 0). 0 inconsistent.
full-scan-rib-ios: Checking IPv6 RIB to FIB consistency
full-scan-rib-ios: FIB checked 16 prefixes, and found 5 missing.
full-scan-ios-rib: Checking IPv6 FIB to RIB consistency
full-scan-ios-rib: Checked 11 FIB prefixes in 1 pass, and found 0 extra.
full-scan-rp-lc: Sent 11 IPv6 prefixes to linecards in 1 pass
full-scan-rp-lc: Initiated IPv6 FIB check on linecards..4..1..0..
full-scan-rp-lc: FIB IPv6 check completed on linecards..1..4..0..
full-scan-rp-lc: Linecard 4 checked 11 IPv6 prefixes (ignored 0). 0 inconsistent.
full-scan-rp-lc: Linecard 1 checked 11 IPv6 prefixes (ignored 0). 0 inconsistent.
full-scan-rp-lc: Linecard 0 checked 11 IPv6 prefixes (ignored 0). 0 inconsistent.
No IPv4 inconsistencies found, check took 00:00:01.444
Warning: 5 IPv6 inconsistencies found, check took 00:00:01.240

Table 98 describes the significant fields shown in the display.

Table 98 test cef consistency detail Field Descriptions

Field
Description

FIB checked 12 prefixes, and found 0 missing

The scan-rib-ios consistency checker checked 12 prefixes in the FIB against the FIB and found 0 missing.

Checked 12 FIB prefixes in 1 pass, and found 0 extra.

The scan-ios-rib consistency checker checked 12 prefixes in the RIB and found no extra prefixes in one pass.

Linecard 4 checked 26 IPv4 prefixes (ignored 0). 0 inconsistent.

The scan-rp-lc consistency checker found no inconsistencies on line card 4 after checking 26 IPv4 prefixes.


Related Commands

Command
Description

cef table consistency check

Enables Cisco Express Forwarding table consistency checker types and parameters.