AutoSecure
First Published: September 27, 2007
Last Updated: April 7, 2011
The AutoSecure feature secures a router by using a single CLI command to disable common IP services that can be exploited for network attacks, enable IP services and features that can aid in the defense of a network when under attack, and simplify and harden the security configuration of the router.
AutoSecure enhances secure access to the router by configuring a required minimum password length to eliminate common passwords that can be common on many networks, such as "lab" and "company name." Syslog messages are generated after the number of unsuccessful attempts exceeds the configured threshold.
AutoSecure also allows a router to revert (roll) back to its pre-AutoSecure configuration state if the AutoSecure configuration fails.
When AutoSecure is enabled, a detailed audit trail of system logging messages capture any changes or tampering of the AutoSecure configuration that may have been applied to the running configuration.
Finding Feature Information
Your software release may not support all the features documented in this module. For the latest feature information and caveats, see the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the "Feature Information for AutoSecure" section.
Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.
Contents
•
Prerequisites for AutoSecure
•
Restrictions for AutoSecure
•
Information About AutoSecure
•
How to Configure AutoSecure
•
Configuration Example for AutoSecure
•
Additional References
•
Feature Information for AutoSecure
Prerequisites for AutoSecure
The AutoSecure configuration was unavailable before Cisco IOS Release 12.3(8)T. If the router were to revert to an image prior to Cisco IOS Release 12.3(8)T, then ensure that a copy of the running configuration is saved before configuring AutoSecure.
Restrictions for AutoSecure
The AutoSecure configuration can be configured at run time or setup time. If any related configuration is modified after AutoSecure has been enabled, the AutoSecure configuration may not be fully effective.
Information About AutoSecure
•
Securing the Management Plane
•
Securing the Forwarding Plane
Securing the Management Plane
The management plane is secured by turning off certain global and interface services that can be potentially exploited for security attacks and turning on global services that help mitigate the threat of attacks. Secure access and secure logging are also configured for the router.
Caution
If your device is managed by a network management (NM) application, securing the management plane could turn off some services like the HTTP server and disrupt the NM application support.
The following subsections define how AutoSecure helps to secure the management plane:
•
Disabling Global Services
•
Disabling Per Interface Services
•
Enabling Global Services
•
Securing Access to the Router
•
Security Logging
Disabling Global Services
After enabling this feature (through the auto secure command), the following global services are disabled on the router without prompting the user:
•
Finger—Collects information about the system (reconnaissance) before an attack. If enabled, the information can leave your device vulnerable to attacks.
•
PAD—Enables all packet assembler and disassembler (PAD) commands and connections between PAD devices and access servers. If enabled, it can leave your device vulnerable to attacks.
•
Small Servers—Causes TCP and User Datagram Protocol (UDP) diagnostic port attacks: a sender transmits a volume of fake requests for UDP diagnostic services on the router, consuming all CPU resources.
•
Bootp Server—Bootp is an insecure protocol that can be exploited for an attack.
•
HTTP Server—Without secure-http or authentication embedded in the HTTP server with an associated ACL, the HTTP server is insecure and can be exploited for an attack. (If you must enable the HTTP server, you are prompted for the proper authentication or access list.)
Note
If you are using Cisco Configuration Professional (CCP), you must manually enable the HTTP server through the ip http server command.
•
Identification Service—An insecure protocol, defined in RFC 1413, that allows one to query a TCP port for identification. An attacker can access private information about the user from the ID server.
•
CDP—If a large number of Cisco Discovery Protocol (CDP) packets are sent to the router, the available memory of the router can be consumed, causing the router to crash.
Caution
NM applications that use CDP to discover network topology are not able to perform discovery.
•
NTP—Without authentication or access-control, Network Time Protocol (NTP) is insecure and can be used by an attacker to send NTP packets to crash or overload the router. (If you want to turn on NTP, you must configure NTP authentication using Message Digest 5 (MD5) and the ntp access-group command. If NTP is enabled globally, disable it on all interfaces on which it is not needed.)
•
Source Routing—Provided only for debugging purposes, so source routing should be disabled in all other cases. Otherwise, packets may slip away from some of the access control mechanisms that they should have gone through.
Disabling Per Interface Services
After enabling this feature, the following per interface services are disabled on the router without prompting the user:
•
ICMP redirects—Disabled on all interfaces. Does not add a useful functionality to a correctly configured to network, but it could be used by attackers to exploit security holes.
•
ICMP unreachables—Disabled on all interfaces. Internet Control Management Protocol (ICMP) unreachables are a known cause for some ICMP-based denial of service (DoS) attacks.
•
ICMP mask reply messages—Disabled on all interfaces. ICMP mask reply messages can give an attacker the subnet mask for a particular subnetwork in the internetwork.
•
Proxy-Arp—Disabled on all interfaces. Proxy-Arp requests are a known cause for DoS attacks because the available bandwidth and resources of the router can be consumed in an attempt to respond to the repeated requests that are sent by an attacker.
•
Directed Broadcast—Disabled on all interfaces. Potential cause of SMURF attacks for DoS.
•
Maintenance Operations Protocol (MOP) service—Disabled on all interfaces.
Enabling Global Services
After AutoSecure is enabled, the following global services are enabled on the router without prompting the user:
•
The service password-encryption command—Prevents passwords from being visible in the configuration.
•
The service tcp-keepalives-in and service tcp-keepalives-out commands—Ensures that abnormally terminated TCP sessions are removed.
Securing Access to the Router
Caution
If your device is managed by an NM application, securing access to the router could turn off vital services and may disrupt the NM application support.
After enabling this feature, the following options in which to secure access to the router are available to the user:
•
If a text banner does not exist, users are prompted to add a banner. This feature provides the following sample banner:
This system is the property of ABC Enterprise
Disconnect IMMEDIATELY if you are not an authorized user!
Contact abc@xyz.com +99 876 543210 for help.
•
The login and password (preferably a secret password, if supported) are configured on the console, AUX, vty, and tty lines. The transport input and transport output commands are also configured on all of these lines. (Telnet and secure shell (SSH) are the only valid transport methods.) The exec-timeout command is configured on the console and AUX as 10.
•
When the image on the device is a crypto image, AutoSecure enables SSH and secure copy (SCP) for access and file transfer to and from the router. The timeout seconds and authentication-retries integer options for the ip ssh command are configured to a minimum number. (Telnet and FTP are not affected by this operation and remain operational.)
•
If the AutoSecure user specifies that their device does not use Simple Network Management Protocol (SNMP), one of the following functions occur:
–
In interactive mode, the user is asked whether to disable SNMP regardless of the values of the community strings, which act like passwords to regulate access to the agent on the router.
–
In non-interact mode, SNMP is disabled if the community string is "public" or "private."
Note
After AutoSecure has been enabled, tools that use SNMP to monitor or configure a device is unable to communicate with the device through SNMP.
•
If authentication, authorization, and accounting (AAA) is not configured, configure local AAA. AutoSecure prompts users to configure a local username and password on the router.
Security Logging
The following logging options are available after AutoSecure is enabled. These options identify security incidents and provide ways to respond to them.
•
Sequence numbers and time stamps for all debug and log messages. This option is useful when auditing logging messages.
•
Logging messages can be generated for login-related events; for example, the message "Blocking Period when Login Attack Detected" is displayed when a login attack is detected and the router enters "quiet mode." (Quiet mode means that the router does not allow any login attempts through Telnet, HTTP, or SSH.)
For more information on login system messages, see the Cisco IOS Release 12.3(4)T feature module Cisco IOS Login Enhancements.
•
The logging console critical command, which sends system logging (syslog) messages to all available TTY lines and limits messages based on severity.
•
The logging buffered command, which copies logging messages to an internal buffer and limits messages logged to the buffer based on severity.
•
The logging trap debugging command, which allows all commands with a severity higher than debugging to be sent to the logging server.
Securing the Forwarding Plane
To minimize the risk of attacks on the router forward plane, AutoSecure provides the following functions:
•
Cisco Express Forwarding (CEF)—AutoSecure enables CEF or distributed CEF (dCEF) on the router whenever possible. Because there is no need to build cache entries when traffic starts arriving for new destinations, CEF behaves more predictably than other modes when presented with large volumes of traffic addressed to many destinations. Thus, routers configured for CEF perform better under SYN attacks than routers using the traditional cache.
Note
CEF consumes more memory than a traditional cache.
•
If the TCP intercept feature is available, it can be configured on the router for connection timeout.
•
If strict Unicast Reverse Path Forwarding (uRPF) is available, it can be configured on the router to help mitigate problems that are caused by the introduction of forged (spoofed) IP source addresses. uRPF discards IP packets that lack a verifiable IP source address.
•
If the router is being used as a firewall, it can be configured for context-based access control (CBAC) on public interfaces that are facing the Internet.
Note
At the beginning of the AutoSecure dialogue, you are prompted for a list of public interfaces.
How to Configure AutoSecure
•
Configuring AutoSecure (required)
•
Configuring Enhanced Security Access to the Router (required)
Configuring AutoSecure
SUMMARY STEPS
1.
enable
2.
auto secure [management | forwarding] [no-interact | full] [ntp | login | ssh | firewall | tcp-intercept]
Caution
Although the
auto secure command helps to secure a router, it does not guarantee the complete security of the router.
DETAILED STEPS
|
|
|
Step 1 |
enable
Router> enable |
Enables higher privilege levels, such as privileged EXEC mode. Enter your password if prompted. |
Step 2 |
auto secure [management | forwarding] [no-interact | full] [ntp | login | ssh | firewall | tcp-intercept]
Router# auto secure |
A semi-interactive dialogue session begins to secure either the management or forwarding planes on the router when the management or forwarding keyword is selected. If neither option is selected, then the dialogue asks for both planes to be configured. If the management keyword is selected, then the management plane is secured only. If the forwarding keyword is selected, then the forwarding plane is secured only. If the no-interact keyword is selected, then the user is not prompted for any interactive configurations. If the full keyword is selected, then user is prompted for all interactive questions, which is the default. |
Configuring Enhanced Security Access to the Router
SUMMARY STEPS
1.
enable
2.
configure terminal
3.
security passwords min-length length
4.
enable password {password | [encryption-type] encrypted-password}
5.
security authentication failure rate threshold-rate log
DETAILED STEPS
|
|
|
Step 1 |
enable
Router> enable |
Enables higher privilege levels, such as privileged EXEC mode. Enter your password if prompted. |
Step 2 |
configure terminal
Router# configure terminal |
Enters global configuration mode. |
Step 3 |
security passwords min-length length
Router(config)# security passwords min-length 6
|
Ensures that all configured passwords are at least a specified length. • length—Minimum length of a configured password. |
Step 4 |
enable password {password | [encryption-type] encrypted-password}
Router(config)# enable password elephant |
Sets a local password to control access to various privilege levels. |
Step 5 |
security authentication failure rate threshold-rate log
Router(config)# security authentication failure rate 10 log |
Configures the number of allowable unsuccessful login attempts. • threshold-rate—Number of allowable unsuccessful login attempts. • log—Syslog authentication failures if the rate exceeds the threshold. |
Step 6 |
exit threshold-rate log
Router(config)# exit |
Exits configuration mode and enters privileged EXEC mode. |
Step 7 |
show auto secure config
Router# show auto secure config
|
(Optional) Displays all configuration commands that have been added as part of the AutoSecure configuration. |
Configuration Example for AutoSecure
The following example is a sample AutoSecure dialogue. After you enable the auto secure command, the feature automatically prompts you with a similar dialogue unless you enable the no-interact keyword. (For information on which services are disabled and which features are enabled, see the sections, "Securing the Management Plane" and "Securing the Forwarding Plane" earlier in this document.)
--- AutoSecure Configuration ---
*** AutoSecure configuration enhances the security of the router but it will not make
router absolutely secure from all security attacks ***
All the configuration done as part of AutoSecure will be shown here. For more details of
why and how this configuration is useful, and any possible side effects, please refer to
Cisco documentation of AutoSecure.
At any prompt you may enter '?' for help.
Use ctrl-c to abort this session at any prompt.
Gathering information about the router for AutoSecure
Is this router connected to internet? [no]:y
Enter the number of interfaces facing internet [1]:
Interface IP-Address OK? Method Status
FastEthernet0/1 10.1.1.1 YES NVRAM up down
FastEthernet1/0 10.2.2.2 YES NVRAM up down
FastEthernet1/1 10.0.0.1 YES NVRAM up up
Loopback0 unassigned YES NVRAM up up
FastEthernet0/0 10.0.0.2 YES NVRAM up down
Enter the interface name that is facing internet:FastEthernet0/0
Securing Management plane services..
Disabling udp & tcp small servers
Enabling service password encryption
Enabling service tcp-keepalives-in
Enabling service tcp-keepalives-out
Disabling the cdp protocol
Disabling the bootp server
Disabling the http server
Disabling the finger service
Enable secret is either not configured or is same as enable password
Enter the new enable secret:abc123
Configuring aaa local authentication
Configuring console, Aux and vty lines for
local authentication, exec-timeout, transport
Configure SSH server? [yes]:
Enter the domain-name:example.com
Configuring interface specific AutoSecure services
Disabling the following ip services on all interfaces:
Disabling mop on Ethernet interfaces
Securing Forwarding plane services..
Enabling CEF (it might have more memory requirements on some low end
Enabling unicast rpf on all interfaces connected to internet
Configure CBAC Firewall feature? [yes/no]:yes
This is the configuration generated:
no service udp-small-servers
no service tcp-small-servers
service password-encryption
service tcp-keepalives-in
service tcp-keepalives-out
security passwords min-length 6
security authentication failure rate 10 log
enable secret 5 $1$CZ6G$GkGOnHdNJCO3CjNHHyTUA.
aaa authentication login local_auth local
login authentication local_auth
login authentication local_auth
login authentication local_auth
ip domain-name example.com
crypto key generate rsa general-keys modulus 1024
ip ssh authentication-retries 2
transport input ssh telnet
service timestamps debug datetime localtime show-timezone msec
service timestamps log datetime localtime show-timezone msec
interface FastEthernet0/0
ip verify unicast reverse-path
ip inspect tcp idle-time 14400
ip inspect udp idle-time 1800
ip inspect name autosec_inspect cuseeme timeout 3600
ip inspect name autosec_inspect ftp timeout 3600
ip inspect name autosec_inspect http timeout 3600
ip inspect name autosec_inspect rcmd timeout 3600
ip inspect name autosec_inspect realaudio timeout 3600
ip inspect name autosec_inspect smtp timeout 3600
ip inspect name autosec_inspect tftp timeout 30
ip inspect name autosec_inspect udp timeout 15
ip inspect name autosec_inspect tcp timeout 3600
access-list 100 deny ip any any
interface FastEthernet0/0
ip inspect autosec_inspect out
Apply this configuration to running-config? [yes]:yes
Applying the config generated to running-config
The name for the keys will be:ios210.example.com
% The key modulus size is 1024 bits
% Generating 1024 bit RSA keys ...[OK]
Additional References
Related Documents
RFCs
|
|
RFC 1918 |
Address Allocation for Private Internets |
RFC 2267 |
Network Ingress Filtering: Defeating Denial of Service Attacks which employ IP Source Address Spoofing |
Technical Assistance
|
|
The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password. |
http://www.cisco.com/cisco/web/support/index.html |
Feature Information for AutoSecure
Table 1 lists the release history for this feature.
Use Cisco Feature Navigator to find information about platform support and software image support. Cisco Feature Navigator enables you to determine which software images support a specific software release, feature set, or platform. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn. An account on Cisco.com is not required.
Note
Table 1 lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.
Table 1 Feature Information for AutoSecure
|
|
|
AutoSecure |
12.3(1) 12.2(18)S 12.3(8)T 12.2(27)SBC |
The AutoSecure feature uses a single CLI command to disable common IP services that can be exploited for network attacks, enable IP services and features that can aid in the defense of a network when under attack, and simplify and harden the security configuration on the router. In Cisco IOS Release 12.3(1)S, this feature was introduced. This feature was integrated into Cisco IOS Release 12.2(18)S. In Cisco IOS Release 12.3(8)T, support for the roll-back functionality and system logging messages were added. This feature was integrated into Cisco IOS Release 12.(27)SBC. The following commands were introduced or modified: auto secure, security passwords min-length, show auto secure config. |
Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1005R)
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.
© 2007-2011 Cisco Systems, Inc. All rights reserved.