How to Configure Controllers
This section contains the following procedures:
Configuring Optics Controller
RP/0/RP0/CPU0:uut#configure
Fri Oct 11 16:22:31.222 UTC
RP/0/RP0/CPU0:uut(config)#controller optics 0/1/0/28
RP/0/RP0/CPU0:uut(config-Optics)#breakout 4x10
RP/0/RP0/CPU0:uut(config-Optics)#commit
Fri Oct 11 16:23:26.868 UTC
RP/0/RP0/CPU0:uut(config-Optics)#end
RP/0/RP0/CPU0:uut#
RP/0/RP0/CPU0:uut#show running-config controller optics 0/1/0/28
Fri Oct 11 16:23:41.273 UTC
controller Optics0/1/0/28
breakout 4x10
!Disabling Optical Modules
This feature provides the ability to disable and re-enable an optical module through CLI, which simulates online insertion and removal (OIR) by disabling power to the transceiver port.
Typical troubleshooting procedures for optical modules can include performing OIR by removing and re-installing the module, which requires onsite personnel to physically reseat the optical module. The ability to remotely disable and enable an optical module can significantly reduce operational expenses.
Example
The following output shows a QSFP28 module powered on and in UP state:
Router# show controllers optics 0/0/0/0
Controller State: Up
Transport Admin State: In Service
Laser State: Off
LED State: Not Applicable
FEC State: FEC ENABLED
Optics Status
Optics Type: QSFP28 100G FR
Wavelength = 1311.00 nm
Alarm Status:
-------------
Detected Alarms: None
LOS/LOL/Fault Status:
Laser Bias Current = 26.2 mA
Actual TX Power = 0.73 dBm
RX Power = -0.68 dBm
Performance Monitoring: Disable
THRESHOLD VALUES
----------------
Parameter High Alarm Low Alarm High Warning Low Warning
------------------------ ---------- --------- ------------ -----------
Rx Power Threshold(dBm) 7.4 -10.4 4.5 -6.3
Tx Power Threshold(dBm) 7.0 -6.3 4.0 -2.4
LBC Threshold(mA) 100.00 8.00 83.00 10.00
Temp. Threshold(celsius) 75.00 -5.00 70.00 0.00
Voltage Threshold(volt) 3.63 2.97 3.46 3.13
Polarization parameters not supported by optics
Temperature = 27.92 Celsius
Voltage = 3.24 V
Transceiver Vendor Details
Form Factor : QSFP28
Optics type : QSFP28 100G FR
Name : CISCO-CISCO
OUI Number : 00.00.0c
Part Number : 10-3248-01
Rev Number : 01
Serial Number : FBN2331A114
PID : QSFP-100G-FR-S
VID : ES0
Date Code(yy/mm/dd) : 19/09/19
To disable the module, use the transceiver disable command in controller optics configuration mode:
Router(config)# controller optics 0/0/0/0
Router(config-Optics)# transceiver disable
Router(config-Optics)# commit
Router(config-Optics)# end
The following example shows the QSFP28 module disabled and powered down:
Router# show controllers optics 0/0/0/0
Controller State: Down
Transport Admin State: In Service
Laser State: Off
Optics Status
Optics Type: Unknown optics
Wavelength = 0.00 nm
Alarm Status:
-------------
Detected Alarms: None
LOS/LOL/Fault Status:
TX Power = N/A
RX Power = N/A
Performance Monitoring: Disable
THRESHOLD VALUES
----------------
Parameter High Alarm Low Alarm High Warning Low Warning
------------------------ ---------- --------- ------------ -----------
Rx Power Threshold(dBm) 7.4 -10.4 4.5 -6.3
Tx Power Threshold(dBm) 7.0 -6.3 4.0 -2.4
LBC Threshold(mA) 100.00 8.00 83.00 10.00
Temp. Threshold(celsius) 75.00 -5.00 70.00 0.00
Voltage Threshold(volt) 3.63 2.97 3.46 3.13
Polarization parameters not supported by optics
Temperature = 0.00 Celsius
Voltage = 0.00 V
Transceiver Vendor Details
To re-enable the module, use the no transceiver disable command in controller optics configuration mode.
Feedback