VXLAN Commands

This section describes the commands used to configure VXLAN.

host-reachability protocol static

To configure the static control protocol for VXLAN tunnel endpoint reachability, use the host-reachability protocol static command in NVE interface configuration mode.

This command has no keywords or arguments.

Command Default

None

Command Modes

NVE interface configuration

Command History

Release Modification

Release 24.2.11

This command was introduced.

Usage Guidelines

No specific guidelines impact the use of this command.

Task ID

Task ID Operation

interface

read, write

tunnel

read, write

Examples

The following example shows control protocol configuration for VXLAN tunnel endpoint reachability. 


Router(config)# interface nve1
Router(config-if)# member vni 2
Router(config-nve-vni)# vrf vrf1
Router(config-nve-vni)# host-reachability protocol protocol static
Router(config-nve-vni)# commit

hw-module profile cef vxlan ipv6-tnl-scale

To increase the VXLAN static routes, use the hw-module profile cef vxlan ipv6-tnl-scale command in the XR Config mode.

This command has no keywords or arguments.

Command Default

None

Command Modes

XR Config

Command History

Release

Modification

Release 24.2.11

This command was introduced.

Usage Guidelines

VXLAN supports up to 160000 static routes by default. However, you can increase the scale value up to one million VXLAN static routes for IPv6 tunnel remote nexthop using the hw-module profile cef vxlan ipv6-tnl-scale command.

Task ID

Task ID

Operations

cef

read, write

Examples

The following example shows how to increase the scale value of VXLAN static routes up to one million: 


Router# configuration
Router(config)# hw-module profile cef vxlan ipv6-tnl-scale
Router(config)# commit

interface nve

To create a network virtualization endpoint (NVE) interface and enter the NVE interface configuration mode, use the interface nve command in XR Config mode. To remove the NVE interface, use the no form of this command.

interface nve nve-id

Syntax Description

nve-id

The NVE interface ID. It can take values from 1 to 65535.

Command Default

None

Command Modes

XR Config

Command History

Release Modification

Release 24.2.11

This command was introduced.

Usage Guidelines

No specific guidelines impact the use of this command.

Task ID

Task ID Operation

interface

read, write

Examples

The following example shows how to create an NVE interface and enter the NVE interface configuration mode. 


Router(config)# interface nve 1
Router(config-if)#

member vni

To map a VXLAN to a network virtualization endpoint (NVE) interface, use the member vni command in the XR Config mode. To remove the VXLAN from the bridge domain, use the no form of this command.

member vni number

Syntax Description

vni

The member virtual network identifier (VNI).

number

The ID of the VXLAN to be mapped to the NVE. The valid values are from 1 to 16777215.

Command Default

None

Command Modes

Bridge-domain configuration

Command History

Release Modification

Release 24.2.11

This command was introduced.

Usage Guidelines

No specific guidelines impact the use of this command.

Task ID

Task ID Operation

interface

read, write

tunnel

read, write

Examples

The following example shows the VXLAN with VNI "2" associated with the NVE "1". 


Router(config)# interface nve 1
Router(config-if)# member vni 2

overlay-encapsulation

To define the encapsulation type for Network Virtualization Endpoint (NVE) interface, use the overlay-encapsulation command in NVE interface configuration mode.

overlay-encapsulation vxlan

Syntax Description

vxlan

Sets VXLAN as an overlay encapsulation type for NVE interface.

Command Default

VXLAN

Command Modes

NVE interface configuration

Command History

Release Modification

Release 24.2.11

This command was introduced.

Usage Guidelines

No specific guidelines impact the use of this command.

Task ID

Task ID Operation

interface

read, write

tunnel

read, write

Examples

The following example shows an NVE interface configured for VXLAN encapsulation. 


Router# configure
Router(config)# interface nve1
Router(config-if)# overlay-encapsulation vxlan
Router(config-nve-encap-vxlan)# commit

peer-ip lookup disable

To disable lookup of peer IP address to accept packets from unknown peers, use the peer-ip lookup disable command in NVE interface configuration mode.

peer-ip lookup disable

This command has no keywords or arguments.

Command Default

None

Command Modes

NVE interface configuration

Command History

Release Modification

Release 24.2.11

This command was introduced.

Usage Guidelines

No specific guidelines impact the use of this command.

Task ID

Task ID Operation

interface

read, write

tunnel

read, write

Examples

The following example shows how to disable lookup of peer-ip to accept packets from unknown peers. 


Router# configure
Router(config)# interface nve1
Router(config-if)# overlay-encapsulation vxlan
Router(config-nve-encap-vxlan)# peer-ip lookup disable
Router(config-nve-encap-vxlan)# commit

show nve interface

To display the network virtualization endpoint (NVE) interface information, use the show nve interface command in XR EXEC mode.

show nve interface [ detail | nve nve-id ]

Syntax Description

detail

Displays detailed information about NVE interfaces.

nve nve-id

Displays information only about the specified NVE interface.

Command Default

None

Command Modes

XR EXEC

Command History

Release Modification
Release 24.2.11

This command was introduced.

Usage Guidelines

No specific guidelines impact the use of this command.

Task ID

Task ID Operation

interface

read

Examples

This is the sample output of the show interface nve command anycast gateway parameters. 

Router# show interface nve100 detail
Interface: nve100 State: Up Encapsulation: VxLAN
  Source Interface: Loopback1 (primary: 10.0.0.1) 
  Source Interface State: Up 
  NVE Flags: 0x1, Admin State: Up, Interface Handle 0xba0
  UDP Port: 4789
  Anycast Source Interface: Loopback100 (primary: 100.1.1.1)

show nve vni

To display list of all VNIs that are associated with various NVE interfaces and the associated multicast IP address that is used for multi-destination frames, use the show nve vni command in XR EXEC mode.

show nve vni [ vni_number | detail | interface nve nve-id ]

Syntax Description

vni_number

Displays output for the specific VNI.

detail

Displays more detailed output.

interface nve nve-id

Displays details for the specific NVE interface.

Command Default

None

Command Modes

XR EXEC

Command History

Release Modification

Release 24.2.11

This command was introduced.

Usage Guidelines

No specific guidelines impact the use of this command.

Task ID

Task ID Operation

tunnel

read

Examples

The following shows an example output of this show command: 

Router# show nve vni 
Interface  VNI          MCAST        VNI State        Mode
nve3       1002         0.0.0.0      Up               L3 Control (Static)
nve1       17001        0.0.0.0      Up               L3 Control (Static)
nve2       17002        0.0.0.0      Up               L3 Control (Static)
nve3       17003        0.0.0.0      Up               L3 Control (Static)

source-interface loopback

To specify a loopback interface whose IP address should be set as the IP address for the NVE interface, use the source-interface loopback command.

source-interface loopback interface-id

Syntax Description

loopback

Specifies a loopback interface as providing IP address for the NVE interface.

interface-id

Specifies the loopback interface ID. It can take values from 0 to 65535.

Command Default

None

Command Modes

NVE interface configuration

Command History

Release Modification

Release 24.2.11

This command was introduced.

Usage Guidelines

No specific guidelines impact the use of this command.

Task ID

Task ID Operation

tunnel

read, write

interface

read, write

Examples

The following example shows how to configure the IP address of an NVE interface as the IP address of a loopback interface. 


Router(config)# interface nve 1
Router(config-if)# source-interface loopback 1