To display status
and configuration information about the Ethernet interfaces on a specific node,
use the
show controllers
command in
XR EXEC mode.
show
controllers
{
TenGigE
| TwentyFiveGigE
| FortyGigE
| HundredGigE
| FourHundredGigE
}
interface-path-id
[
all
| description
| periodic
| pm
| bert
| internal
| mac
| phy
| stats
| xgxs
]
Syntax Description
|
{TenGigE| HundredGigE}
|
Specifies the type of Ethernet interface whose status and configuration information you want to display.
|
|
interface-path-id
|
Physical
interface or virtual interface.
|
Note
|
Use the
show
interfaces command to see a list of all interfaces
currently configured on the router.
|
For more
information about the syntax for the router, use the question mark (? ) online help function.
|
|
all
|
Displays
detailed information for the specified interface.
|
|
bert
|
Displays
BERT status information for the interface.
|
|
internal
|
Displays
internal information for the interface.
|
|
mac
|
Displays
mac information for the interface.
|
|
phy
|
Displays
physical information for the interface.
|
|
stats
|
Displays
statistical information for the interface.
|
|
xgxs
|
Displays
information about the 10 Gigabit Ethernet Extended Sublayer (XGXS).
|
Command Default
No default
behavior or values
Command Modes
XR EXEC mode
Command History
|
Release
|
Modification
|
|
Release 6.0
|
This command was introduced.
|
Usage Guidelines
For the interface-path-id argument, use the following guidelines:
-
If specifying a physical interface, the naming notation is rack/slot/module/port. The slash between values is required as part of the notation. An explanation of each component of the naming notation is
as follows:
-
rack: Chassis number of the rack.
-
slot: Physical slot number of the line card.
-
module: Module number. Always 0.
-
port: Physical port number of the interface.
-
If specifying a virtual interface, the number range varies, depending on interface type.
Note
|
When the NC57-MPA-1FH1D-S modular port adapter is plugged into the NC57-MOD-S line card, the Forward Error Correction (FEC)
is disabled for 100GE for optics.
|
Note
|
The Forward Error Correction (FEC) is disabled for 25GE, and 100GE optics in the NCS57-MOS-S line card.
|
Task ID
|
Task ID
|
Operations
|
|
cisco-support
|
read
|
Note
|
Required
in addition to the interface (read) task ID to use the
control
keyword only.
|
|
|
dwdm
|
read
|
|
interface
|
read
|
|
sonet-sdh
|
read
|
Examples
The following example shows sample output from the
show controllers
TenGigE command:
RP/0/RP0/CPU0:router# show controllers TenGigE 0/0/0/3
PHY:
XENPAK device registers:
========================
Vendor Name: CISCO-SUMITOMO
Vendor PN: SXP3101NV-C1
Vendor Rev: A1
Vendor SN: ECL120701L2
Package OUI: 0041f426
Vendor OUI: 00137b11
Vendor Date Code: 2004071200
nvr_control_status = 0x0007
nvr_version = 0x1e
nvr_size0 = 0x01
nvr_size1 = 0x00
mem_used0 = 0x01
mem_used1 = 0x00
basic_addr = 0x0b
cust_addr = 0x77
vend_addr = 0xa7
ext_vend_addr0= 0x00
ext_vend_addr1= 0xff
reserved0 = 0x00
tcvr_type = 0x01
connector = 0x01
encoding = 0x01
bitrate0 = 0x27
bitrate1 = 0x10
protocol = 0x01
x_gbe_code_byte_0 = 0x02
x_gbe_code_byte_1 = 0x00
sonet_sdh_code_byte_0 = 0x00
sonet_sdh_code_byte_1 = 0x00
sonet_sdh_code_byte_2 = 0x00
sonet_sdh_code_byte_3 = 0x00
x_gfc_code_byte_0 = 0x00
x_gfc_code_byte_1 = 0x00
x_gfc_code_byte_2 = 0x00
x_gfc_code_byte_3 = 0x00
range0 = 0x03
range1 = 0xe8
fibre_type_byte_0 = 0x20
fibre_type_byte_1 = 0x00
Center Wavelength:
chan0 = 1310.00 nm
chan1 = 0.00 nm
chan2 = 0.00 nm
chan3 = 0.00 nm
basic_checksum = 0x00
Link Alarm Status Registers:
rx_alarm_control = 0x0019
tx_alarm_control = 0x0059
lasi_control = 0x0000
rx_alarm_status = 0x0018
tx_alarm_status = 0x0058
lasi_status = 0x0005
Digital Optical Monitoring:
Transceiver Temp: 34.246 C
Laser Bias Current: 4.8640 mA
Laser Output Power: 0.5059 mW, -3.0 dBm
Receive Optical Power: 0.0000 mW, -inf dBm
Quake: devid 0x0043a400
10GE PMA/PMD Registers:
Control = 0x2040 Status = 0x0082 Dev ID 0 = 0x0043 Dev ID 1 = 0xa400 Speed Ability =
0x0001 Devices 1 = 0x001a Devices 2 = 0x0000 Control 2 = 0x0006 Status 2 = 0xb541 Tx
Disable = 0x0000 Rx Signal Detect = 0x0000 OUI 0 = 0x0041 OUI 1 = 0xf426
Quake (1.c001) = 0x0003
10GE PCS Registers:
Control = 0x2040 Status = 0x0082 Dev ID 0 = 0x0043 Dev ID 1 = 0xa400 Speed Ability =
0x0001 Devices 1 = 0x001a Devices 2 = 0x0000 Control 2 = 0x0000 Status 2 = 0x8401 PKG ID 0
= 0x0000 PKG ID 1 = 0x0000 Base X Status = 0x0000 Base X Control = 0x0000 Base R Status 1
= 0x0004 Base R Status 2 = 0x0000 Base R jitter seed a0 = 0x0000 Base R jitter seed a1 =
0x0000 Base R jitter seed a2 = 0x0000 Base R jitter seed a3 = 0x0000 Base R jitter seed b0
= 0x0000 Base R jitter seed b1 = 0x0000 Base R jitter seed b2 = 0x0000 Base R jitter seed
b3 = 0x0000 Base R jitter test control = 0x0000 Base R jitter test counter = 0x0000
10GE XS/XS Registers:
Control = 0x2040 Status = 0x0002
Dev ID 0 = 0x0043 Dev ID 1 = 0xa400
Speed Ability = 0x0001 Devices 1 = 0x001a Devices 2 = 0x0000 Status 2 = 0x8000 PKG ID 0 =
0x0000 PKG ID 1 = 0x0000 Lane Status = 0x1c0f Test Control = 0x0000
DTE XGXS (BCM8011):
Control = 0x0000 Status = 0x801f
Dev ID 0 = 0x0040 Dev ID 1 = 0x6092
Control 2 = 0x202f
Status 2 = 0x8b01
Speed Ability = 0x0001 Devices 1 = 0x001a Devices 2 = 0x0000 Status 2 = 0x8000 PKG ID 0 =
0x0000 PKG ID 1 = 0x0000 Lane Status = 0x1c0f Test Control = 0x0000
DTE XGXS (BCM8011):
Control = 0x0000 Status = 0x801f
Dev ID 0 = 0x0040 Dev ID 1 = 0x6092
Control 2 = 0x202f
Status 2 = 0x8b01
MAC (PLA):
Unicast MAC Address entries = 0
MAC (PLA) device is enabled
MAC (PLA) device is in promiscuous mode
MAC (PLA) device loopback is disabled
MAC (PLA) device MTU = 8226
8x10GE PLIM Registers:
local_regs_id = 0xa6602000 local_regs_inter_stat = 0x00000000 local_regs_inter_stat_alias
= 0x00000000 local_regs_inter_enbl_woset = 0x0000ff00 local_regs_inter_enbl_woclr =
0x0000ff00 local_regs_chip_reset = 0x00000000 local_regs_reset = 0xff000000
local_regs_misc_io = 0x00010000 sn_link_framed = 0x00000001 sn_link_crc_errors =
0x00000000 sn_link_force_reframe = 0x00000000 sn_link_error_reframe = 0x00000001
sn_link_force_error = 0x00000000 sn_link_error_cause = 0x00000000
sn_link_error_interrupt_mask = 0x00000003 channel0_control = 0x000000a6 channel1_control =
0x000000a6 channel2_control = 0x0000008e channel3_control = 0x0000008e channel4_control =
0x0000008e channel5_control = 0x000000a6 channel6_control = 0x000000a6 channel7_control =
0x0000008e
The following
example shows sample output from the base form of the
show controllers TenGigE all
command:
RP/0/RP0/CPU0:router# show controllers TenGigE 0/0/0/4 all
Operational data for interface TenGigE0/0/0/4:
State:
Administrative state: disabled
Operational state: Down (Reason: The optics for the port are not present)
LED state: Yellow On
Media:
Media type: Initializing, true state or type not yet known
No optics present
MAC address information:
Operational address: 001d.353b.975e
Burnt-in address: 001d.353b.975e
No unicast addresses in filter
No multicast addresses in filter
Autonegotiation disabled.
Operational values:
Speed: 10Gbps
Duplex: Full Duplex
Flowcontrol: None
Loopback: None (or external)
MTU: 1526
MRU: 1526
Inter-packet gap: standard (12)
BERT status for TenGigE0/0/0/4:
BERT State : DISABLED
Test Pattern : None test pattern
Time Remaining : 0
Time Interval : 0
Statistics for interface TenGigE0/0/0/4 (cached values):
Ingress:
Input total bytes = 0
Input good bytes = 0
Input total packets = 0
Input 802.1Q frames = 0
Input pause frames = 0
Input pkts 64 bytes = 0
Input pkts 65-127 bytes = 0
Input pkts 128-255 bytes = 0
Input pkts 256-511 bytes = 0
Input pkts 512-1023 bytes = 0
Input pkts 1024-1518 bytes = 0
Input pkts 1519-Max bytes = 0
Input good pkts = 0
Input unicast pkts = 0
Input multicast pkts = 0
Input broadcast pkts = 0
Input drop overrun = 0
Input drop abort = 0
Input drop unknown 802.1Q = 0
Input drop other = 0
Input error giant = 0
Input error runt = 0
Input error jabbers = 0
Input error fragments = 0
Input error CRC = 0
Input error collisions = 0
Input error symbol = 0
Input error other = 0
Input MIB giant = 0
Input MIB jabber = 0
Input MIB CRC = 0
Egress:
Output total bytes = 0
Output good bytes = 0
Output total packets = 0
Output 802.1Q frames = 0
Output pause frames = 0
Output pkts 64 bytes = 0
Output pkts 65-127 bytes = 0
Output pkts 128-255 bytes = 0
Output pkts 256-511 bytes = 0
Output pkts 512-1023 bytes = 0
Output pkts 1024-1518 bytes = 0
Output pkts 1519-Max bytes = 0
Output good pkts = 0
Output unicast pkts = 0
Output multicast pkts = 0
Output broadcast pkts = 0
Output drop underrun = 0
Output drop abort = 0
Output drop other = 0
Output error other = 0
Management information for interface TenGigE0/0/0/4:
Port number: 2
Bay number: 0
Interface handle: 0x100000c0
Config:
Auto-negotiation: Configuration not supported (Off)
Carrier delay (up): Not configured
Carrier delay (down): Not configured
Speed: Configuration not supported (10Gbps)
Duplex: Configuration not supported (Full Duplex)
Flow Control: Not configured (None)
IPG: Not configured (standard (12))
Loopback: Not configured (None)
MTU: Not configured
Soft Bandwidth: Not configured
Driver constraints:
Min MTU: 64 bytes
Max MTU: 9216 bytes
Max speed: 10Gbps
Interface type: TenGigE
Management interface: No
Promiscuous mode: Yes
Allowed config mask: 0x27b
Cached driver state:
MTU: 1522 bytes
Burnt-in MAC address: 001d.353b.975e
Bundle settings:
Aggregated: No
Bundle MTU: 1514 bytes
Bundle MAC address: 001d.353b.975e
Port FSM state:
Port is disabled, due to an admin down condition.
Complete FSM state:
Admin down
Bundle admin up
Client admin up
Client admin tx not disabled
Port disabled
Port tx disabled
Hardware link down
IDB interface state information:
IDB bundle admin up
IDB client admin up
IDB client tx admin up
IDB error disable not set
0 Unicast MAC Addresses:
0 Multicast MAC Addresses:
0 Unicast Bundle MAC Addresses:
0 Multicast Bundle MAC Addresses:
Current Data
NP(01) Version : 0003
Structure Version : 2582
XAUI Interface : B
MAC addr : 00.1d.35.3b.97.5e
RX enabled : False
TX enabled : True
Obey Pause Frames : False
TX Pause Frames : False
Pause Re-TX Period : 3000000
Min Frame Len : 60
Max Frame Len : 1526
Ignore Errors : False
Add CRC : True
Strip CRC : True
Ignore CRC Errors : False
DMA Add CRC : False
DMA Strip CRC : False
Ignore Length Error: True
Pad Short Frames : True
Min TX IFG : 12
Min RX IFG : 4
IFG Rate Control : False
Hi Gig Mode : False
Discard Ctrl Frames: True
Enable Stats Update: True
RX Stats Int Mask : 0x00000000
TX Stats Int Mask : 0x00000000
Port Number : 2
Port Type : 10GE
Transport mode : LAN
BIA MAC addr : 001d.353b.975e
Oper. MAC addr : 001d.353b.975e
Port Available : true
Status polling is : enabled
Status events are : enabled
I/F Handle : 0x100000c0
Cfg Link Enabled : disabled
H/W Tx Enable : yes
MTU : 1526
H/W Speed : 10 Gbps
H/W Duplex : Full
H/W Loopback Type : None
H/W FlowCtrl type : None
H/W AutoNeg Enable: Off
H/W Link Defects : interface is admin down
Link Up : no
Link Led Status : Shutdown
Symbol errors : 0
Serdes version : 14.42
Input good underflow : 0
Input ucast underflow : 0
Output ucast underflow : 0
Input unknown opcode underflow: 0
Pluggable Present : no
Pluggable Type : Unknown pluggable optics
Pluggable Compl. : Not Checked
Pluggable Type Supp.: Not Checked
Pluggable PID Supp. : Not Checked
Pluggable Scan Flg: false
XFP #2 is not present
Serdes Registers and info port: 2
EDC Status : 000000050 - EDC Aquiring
Rx detected : No
Block lock : No
Tx aligned : Yes
The following example shows sample output from the
show controllers TenGigE
bert command:
RP/0/RP0/CPU0:router# show controllers TenGigE 0/0/0/2 bert
BERT status for TenGigE0/0/0/2:
BERT State : DISABLED
Test Pattern : None test pattern
Time Remaining : 0
Time Interval : 0
The following
example shows sample output from the
show controllers TenGigE control command:
RP/0/RP0/CPU0:router# show controllers TenGigE 0/0/0/2 control
Management information for interface TenGigE0/0/0/2:
Port number: 2
Bay number: 0
Interface handle: 0x100000c0
Config:
Auto-negotiation: Configuration not supported (Off)
Carrier delay (up): Not configured
Carrier delay (down): Not configured
Speed: Configuration not supported (10Gbps)
Duplex: Configuration not supported (Full Duplex)
Flow Control: Not configured (None)
IPG: Not configured (standard (12))
Loopback: Not configured (None)
MTU: Not configured
Soft Bandwidth: Not configured
Driver constraints:
Min MTU: 64 bytes
Max MTU: 9216 bytes
Max speed: 10Gbps
Interface type: TenGigE
Management interface: No
Promiscuous mode: Yes
Allowed config mask: 0x27b
Cached driver state:
MTU: 1522 bytes
Burnt-in MAC address: 001d.353b.975e
Bundle settings:
Aggregated: No
Bundle MTU: 1514 bytes
Bundle MAC address: 001d.353b.975e
Port FSM state:
Port is disabled, due to an admin down condition.
Complete FSM state:
Admin down
Bundle admin up
Client admin up
Client admin tx not disabled
Port disabled
Port tx disabled
Hardware link down
IDB interface state information:
IDB bundle admin up
IDB client admin up
IDB client tx admin up
IDB error disable not set
0 Unicast MAC Addresses:
0 Multicast MAC Addresses:
0 Unicast Bundle MAC Addresses:
0 Multicast Bundle MAC Addresses:
The following example shows sample output from the
show controllers TenGigE
internal command:
RP/0/RP0/CPU0:router#show controllers TenGigE 0/0/0/4 internal
Port Number : 0
Port Type : 10GE
Transport mode : LAN
BIA MAC addr : 001b.53ff.a780
Oper. MAC addr : 001b.53ff.a780
Port Available : true
Status polling is : enabled
Status events are : enabled
I/F Handle : 0x0c000040
Cfg Link Enabled : tx/rx enabled
H/W Tx Enable : yes
MTU : 9112
H/W Speed : 10 Gbps
H/W Duplex : Full
H/W Loopback Type : None
H/W FlowCtrl type : None
H/W AutoNeg Enable: Off
H/W Link Defects : (0x0000) None
Link Up : yes
Link Led Status : Link up
Symbol errors : 255
Serdes version : 14.42
Input good underflow : 0
Input ucast underflow : 0
Output ucast underflow : 0
Input unknown opcode underflow: 0
Pluggable Present : yes
Pluggable Type : 10GBASE-LR
Pluggable Compl. : Compliant
Pluggable Type Supp.: Supported
Pluggable PID Supp. : Supported
Pluggable Scan Flg: false
The following
example shows sample output from the
show controllers TenGigE stats command:
RP/0/RP0/CPU0:router# show controllers TenGigE 0/0/0/4 stats
Statistics for interface TenGigE0/0/0/0 (cached values):
Ingress:
Input total bytes = 9614339316
Input good bytes = 9614339316
Input total packets = 106713557
Input 802.1Q frames = 0
Input pause frames = 0
Input pkts 64 bytes = 103907216
Input pkts 65-127 bytes = 2494185
Input pkts 128-255 bytes = 3410
Input pkts 256-511 bytes = 3406
Input pkts 512-1023 bytes = 2
Input pkts 1024-1518 bytes = 0
Input pkts 1519-Max bytes = 305338
Input good pkts = 106713557
Input unicast pkts = 105627141
Input multicast pkts = 1086414
Input broadcast pkts = 2
Input drop overrun = 0
Input drop abort = 0
Input drop unknown 802.1Q = 0
Input drop other = 0
Input error giant = 0
Input error runt = 0
Input error jabbers = 0
Input error fragments = 0
Input error CRC = 0
Input error collisions = 0
Input error symbol = 0
Input error other = 0
Input MIB giant = 305338
Input MIB jabber = 0
Input MIB CRC = 0
Egress:
Output total bytes = 15202682421
Output good bytes = 15202682421
Output total packets = 107534855
Output 802.1Q frames = 0
Output pause frames = 0
Output pkts 64 bytes = 103862713
Output pkts 65-127 bytes = 2448054
Output pkts 128-255 bytes = 308716
Output pkts 256-511 bytes = 6
Output pkts 512-1023 bytes = 13
Output pkts 1024-1518 bytes = 0
Output pkts 1519-Max bytes = 915353
Output good pkts = 107534855
Output unicast pkts = 105321133
Output multicast pkts = 1298368
Output broadcast pkts = 1
Output drop underrun = 0
Output drop abort = 0
Output drop other = 0
Output error other = 0
Feedback