The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
Network Time Protocol (NTP) is a protocol designed to time-synchronize devices within a network. Cisco IOS XR software implements NTPv4. NTPv4 retains backwards compatibility with the older versions of NTP, including NTPv3 and NTPv2 but excluding NTPv1, which has been discontinued due to security vulnerabilities.
You must be in a user group associated with a task group that includes the proper task IDs. The command reference guides include the task IDs required for each command. If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
NTP synchronizes timekeeping among a set of distributed time servers and clients. This synchronization allows events to be correlated when system logs are created and other time-specific events occur.
NTP uses the User Datagram Protocol (UDP) as its transport protocol. All NTP communication uses Coordinated Universal Time (UTC). An NTP network usually receives its time from an authoritative time source, such as a radio clock or an atomic clock attached to a time server. NTP distributes this time across the network. NTP is extremely efficient; no more than one packet per minute is necessary to synchronize two machines to within a millisecond of each other.
NTP uses the concept of a “stratum” to describe how many NTP “hops” away a machine is from an authoritative time source. A “stratum 1” time server typically has an authoritative time source (such as a radio or atomic clock, or a GPS time source) directly attached, a “stratum 2” time server receives its time via NTP from a “stratum 1” time server, and so on.
NTP avoids synchronizing to a machine whose time may not be accurate, in two ways. First, NTP never synchronizes to a machine that is not synchronized itself. Second, NTP compares the time reported by several machines and does not synchronize to a machine whose time is significantly different than the others, even if its stratum is lower. This strategy effectively builds a self-organizing tree of NTP servers.
The Cisco implementation of NTP does not support stratum 1 service; in other words, it is not possible to connect to a radio or atomic clock (for some specific platforms, however, you can connect a GPS time-source device). We recommend that time service for your network be derived from the public NTP servers available in the IP Internet.
If the network is isolated from the Internet, the Cisco implementation of NTP allows a machine to be configured so that it acts as though it is synchronized via NTP, when in fact it has determined the time using other means. Other machines can then synchronize to that machine via NTP.
Several manufacturers include NTP software for their host systems, and a publicly available version for systems running UNIX and its various derivatives is also available. This software also allows UNIX-derivative servers to acquire the time directly from an atomic clock, which would subsequently propagate time information along to Cisco routers.
The communications between machines running NTP (known as associations) are usually statically configured; each machine is given the IP address of all machines with which it should form associations. Accurate timekeeping is made possible by exchanging NTP messages between each pair of machines with an association.
The Cisco implementation of NTP supports three ways that a networking device can obtain NTP time information on a network:
By polling host servers
By listening to NTP broadcasts
By listening to NTP multicasts
By using a peer-to-peer relationship.
In a LAN environment, NTP can be configured to use IP broadcast or multicast messages. As compared to polling, IP broadcast or multicast messages reduce configuration complexity, because each machine can simply be configured to send or receive broadcast or multicast messages. However, the accuracy of timekeeping is marginally reduced because the information flow is one-way only.
An NTP broadcast client listens for broadcast messages sent by an NTP broadcast server at a designated IPv4 address. The client synchronizes the local clock using the first received broadcast message.
An NTP multicast server periodically sends a message to a designated IPv4 or IPv6 local multicast group address. An NTP multicast client listens on this address for NTP messages.
The time kept on a machine is a critical resource, so we strongly recommend that you use the security features of NTP to avoid the accidental or malicious setting of incorrect time. Two mechanisms are available: an access list-based restriction scheme and an encrypted authentication mechanism.
When multiple sources of time (VINES, hardware clock, manual configuration) are available, NTP is always considered to be more authoritative. NTP time overrides the time set by any other method.
If there are no GPS sources in the NTP source chain or server chain, there is no impact of GPS Week Number Rollover (WNRO).
GPS WNRO affects only the system clock and not user traffic.
Contact your GPS manufacturer to fix the GPS source for this condition.
To mitigate impact of GPS sources that are subject to GPS WNRO perform the following optional workarounds:
If the GPS source has been identified to be a cause of potential disruption on April 6, 2019 (or after), configure ntp master in the Cisco that is device connected to this source, and its clock on the Stratum 1 device to preventively isolate it. This configuration enables the device to present its own clock for synchronization to downstream NTP clients.
 Note |
The usage of ntp master command as mentioned above is only a workaround to this condition. Use this command until the GPS source-related conditions are resolved, and to prevent the distribution of incorrect clock values throughout the network. |
Configure multiple NTP servers (ideally 4, but more than 3) at Stratum 2 level of the network, to enable NTP clients at Stratum 2 level to get clock from more than one Stratum 1 server. This way, WNRO affected Stratum 1 servers are staged to be marked as ‘false ticker’ or ‘outlier’ clock sources as compared to other non-WNRO affected Stratum 1 servers.
Note |
To configure day light saving time (DST) on your IOS XR 64-bit device, select the appropriate country and city. The device will automatically update the DST based on the internal mappings at kernel level. The DST keyword is not available in the configuration CLI, since manual configuration of DST is not supported on IOS XR 64-bit devices. |
NTP-PTP interworking provides the ability to use PTP, as well as other valid time of day (TOD) sources such as Data over Cable Service Interface Specification (DOCSIS) Timing Interface (DTI) and global positioning system (GPS), as the time source for the operating system. Prior to the support of NTP-PTP interworking, only backplane time was supported for the operating system time.
NTP-PTP interworking also provides the means to communicate status changes between PTP and NTP processes. It also supports the unambiguous control of the operating system time and backplane time in the event of bootup, switchovers or card and process failures.
For information regarding configuring NTP-PTP interworking, refer to System Management Configuration Guide for Cisco NCS 5500 Series Routers.
Note |
No specific command enables NTP; the first NTP configuration command that you issue enables NTP. |
You can configure the following types of poll-based associations between the router and other devices (which may also be routers):
Client mode
Symmetric active mode
The client and the symmetric active modes should be used when NTP is required to provide a high level of time accuracy and reliability.
When a networking device is operating in the client mode, it polls its assigned time serving hosts for the current time. The networking device then picks a host from all the polled time servers to synchronize with. Because the relationship that is established in this case is a client-host relationship, the host does not capture or use any time information sent by the local client device. This mode is most suited for file-server and workstation clients that are not required to provide any form of time synchronization to other local clients. Use the server command to individually specify the time-serving hosts that you want your networking device to consider synchronizing with and to set your networking device to operate in the client mode.
When a networking device is operating in the symmetric active mode, it polls its assigned time-serving hosts for the current time and it responds to polls by its hosts. Because this is a peer-to-peer relationship, the host also retains time-related information about the local networking device that it is communicating with. This mode should be used when there are several mutually redundant servers that are interconnected via diverse network paths. Most stratum 1 and stratum 2 servers on the Internet today adopt this form of network setup. Use the peer command to individually specify the time-serving hosts that you want your networking device to consider synchronizing with and to set your networking device to operate in the symmetric active mode.
When the router polls several other devices for the time, the router selects one device with which to synchronize.
Note |
To configure a peer-to-peer association between the router and another device, you must also configure the router as a peer on the other device. You can configure multiple peers and servers, but you cannot configure a single IP address as both a peer and a server at the same time. To change the configuration of a specific IP address from peer to server or from server to peer, use the no form of the peer or server command to remove the current configuration before you perform the new configuration. If you do not remove the old configuration before performing the new configuration, the new configuration does not overwrite the old configuration. |
| Command or Action | Purpose | |||
|---|---|---|---|---|
|
Step 1 |
configure Example: |
Enters global configuration mode. |
||
|
Step 2 |
ntp Example: |
Enters NTP configuration mode. |
||
|
Step 3 |
server ip-address [ vrf vrf] [version number] [key key-id] [minpoll interval] [maxpoll interval] [source type interface-path-id] [prefer] [burst] [iburst] Example: |
Forms a server association with another system. This step can be repeated as necessary to form associations with multiple devices. |
||
|
Step 4 |
peer ip-address[ vrf vrf] [version number] [key key-id] [minpoll interval] [maxpoll interval] [source type interface-path-id] [prefer] Example: |
Forms a peer association with another system. This step can be repeated as necessary to form associations with multiple systems.
|
||
|
Step 5 |
Use one of the following commands:
Example:or |
Saves configuration changes.
|
In a broadcast-based NTP association, an NTP server propagates NTP broadcast packets throughout a network. Broadcast clients listen for the NTP broadcast packets propagated by the NTP server and do not engage in any polling.
Broadcast-based NTP associations should be used when time accuracy and reliability requirements are modest and if your network is localized and has a large number of clients (more than 20). Broadcast-based NTP associations also are recommended for use on networks that have limited bandwidth, system memory, or CPU resources. Time accuracy is marginally reduced in broadcast-based NTP associations because information flows only one way.
Use the broadcast client command to set your networking device to listen for NTP broadcast packets propagated through a network. For broadcast client mode to work, the broadcast server and its clients must be located on the same subnet. The time server that is transmitting NTP broadcast packets must be enabled on the interface of the given device using the broadcast command.
Use the broadcast command to set your networking device to send NTP broadcast packets.
Note |
No specific command enables NTP; the first NTP configuration command that you issue enables NTP. |
| Command or Action | Purpose | |||
|---|---|---|---|---|
|
Step 1 |
configure Example: |
Enters global configuration mode. |
||
|
Step 2 |
ntp Example: |
Enters NTP configuration mode. |
||
|
Step 3 |
(Optional) broadcastdelay microseconds Example: |
(Optional)
Adjusts the estimated round-trip delay for NTP broadcasts. |
||
|
Step 4 |
interface type interface-path-id Example: |
Enters NTP interface configuration mode. |
||
|
Step 5 |
broadcast client Example: |
Configures the specified interface to receive NTP broadcast packets.
|
||
|
Step 6 |
broadcast [destination ip-address] [key key-id] [version number] Example: |
Configures the specified interface to send NTP broadcast packets.
|
||
|
Step 7 |
Use one of the following commands:
Example:or |
Saves configuration changes.
|
Note |
No specific command enables NTP; the first NTP configuration command that you issue enables NTP. |
The access list-based restriction scheme allows you to grant or deny certain access privileges to an entire network, a subnet within a network, or a host within a subnet. NTP communication consists of time requests and control queries. A time request is a request for time synchronization from an NTP server. A control query is a request for configuration information from an NTP server.
The access group options are scanned in the following order, from least restrictive to most restrictive:
query-only—Allows only NTP control queries from a system whose address passes the access list criteria.
If the source IP address matches the access lists for more than one access type, the first type is granted. If no access groups are specified, all access types are granted to all systems. If any access groups are specified, only the specified access types are granted.
For details on NTP control queries, see RFC 1305 (NTP version 3).
| Command or Action | Purpose | |
|---|---|---|
|
Step 1 |
configure Example: |
Enters global configuration mode. |
|
Step 2 |
ntp Example: |
Enters NTP configuration mode. |
|
Step 3 |
access-group{peer | query-only | serve | serve-only} access-list-name Example: |
Creates an access group and applies a basic IPv4 or IPv6 access list to it. |
|
Step 4 |
Use one of the following commands:
Example:or |
Saves configuration changes.
|
This task explains how to configure NTP authentication.
Note |
No specific command enables NTP; the first NTP configuration command that you issue enables NTP. |
The encrypted NTP authentication scheme should be used when a reliable form of access control is required. Unlike the access-list-based restriction scheme that is based on IP addresses, the encrypted authentication scheme uses authentication keys and an authentication process to determine if NTP synchronization packets sent by designated peers or servers on a local network are deemed as trusted, before the time information that it carries along is accepted.
The authentication process begins from the moment an NTP packet is created. A message authentication code (MAC) is computed using the MD5 Message Digest Algorithm and the MAC is embedded into an NTP synchronization packet. The NTP synchronization packet together with the embedded MAC and key number are transmitted to the receiving client. If authentication is enabled and the key is trusted, the receiving client computes the MAC in the same way. If the computed MAC matches the embedded MAC, the system is allowed to sync to the server that uses this key in its packets.
After NTP authentication is properly configured, your networking device only synchronizes with and provides synchronization to trusted time sources.
| Command or Action | Purpose | |
|---|---|---|
|
Step 1 |
configure Example: |
Enters global configuration mode. |
|
Step 2 |
ntp Example: |
Enters NTP configuration mode. |
|
Step 3 |
authenticate Example: |
Enables the NTP authentication feature. |
|
Step 4 |
authentication-key key-number md5 [clear | encrypted] key-name Example: |
Defines the authentication keys.
|
|
Step 5 |
trusted-key key-number Example: |
Defines trusted authentication keys.
|
|
Step 6 |
Use one of the following commands:
Example:or |
Saves configuration changes.
|
NTP services are disabled on all interfaces by default.
NTP is enabled globally when any NTP commands are entered. You can selectively prevent NTP packets from being received through a specific interface by turning off NTP on a given interface.
| Command or Action | Purpose | |
|---|---|---|
|
Step 1 |
configure Example: |
Enters global configuration mode. |
|
Step 2 |
ntp Example: |
Enters NTP configuration mode. |
|
Step 3 |
Use one of the following commands:
Example:or |
Disables NTP services on the specified interface. |
|
Step 4 |
Use one of the following commands:
Example:or |
Saves configuration changes.
|
By default, the source IP address of an NTP packet sent by the router is the address of the interface through which the NTP packet is sent. Use this procedure to set a different source address.
Note |
No specific command enables NTP; the first NTP configuration command that you issue enables NTP. |
| Command or Action | Purpose | |||
|---|---|---|---|---|
|
Step 1 |
configure Example: |
Enters global configuration mode. |
||
|
Step 2 |
ntp Example: |
Enters NTP configuration mode. |
||
|
Step 3 |
source type interface-path-id Example: |
Configures an interface from which the IP source address is taken.
|
||
|
Step 4 |
Use one of the following commands:
Example:or |
Saves configuration changes.
|
You can configure the router to act as an authoritative NTP server, even if the system is not synchronized to an outside time source.
Note |
No specific command enables NTP; the first NTP configuration command that you issue enables NTP. |
| Command or Action | Purpose | |||
|---|---|---|---|---|
|
Step 1 |
configure Example: |
Enters global configuration mode. |
||
|
Step 2 |
ntp Example: |
Enters NTP configuration mode. |
||
|
Step 3 |
master stratum Example: |
Makes the router an authoritative NTP server.
|
||
|
Step 4 |
Use one of the following commands:
Example:or |
Saves configuration changes.
|
Use this task to configure NTP to use PTP as the time source.
PTP must be supported and enabled on the router before NTP-PTP interworking can be configured. If PTP is not enabled, you receive an error message similar to the following when you try to commit the configuration:
RP/0/RP0/CPU0:router(config)# ntp master primary-reference-clock
RP/0/RP0/CPU0:router(config)# commit
% Failed to commit one or more configuration items. Please issue
'show configuration failed' from this session to view the errors
RP/0/RP0/CPU0:router(config)# show configuration failed
[:::]
ntp
master primary-reference-clock
!!% 'ip-ntp' detected the 'fatal' condition 'PTP is not supported on this platform'
!
end
| Command or Action | Purpose | |
|---|---|---|
|
Step 1 |
configure Example: |
Enters global configuration mode. |
|
Step 2 |
ntp Example: |
Enters NTP configuration mode. |
|
Step 3 |
master primary-reference-clock Example: |
Specifies PTP to be the NTP time source. |
|
Step 4 |
Use one of the following commands:
Example:or |
Saves configuration changes.
|
NTP on Cisco IOS XR Software supports configuration of servers and peers using their Fully Qualified Domain Names (FQDN). While configuring, the FQDN is resolved via DNS into its corresponding IPv4 or IPv6 address and is stored in the running-configuration of the system. NTP supports FQDN for both IPv4 and IPv6 protocols. You can configure FQDN on default vrf.
Use the ntp server command with the FQDN name to configure FQDN on default VRF. You dont need to specify VRF name. In the following example, time.cisco.com is the FQDN.
Router#configure
Router(config)#ntp server time.cisco.com
Router(config)#commit
Note |
When you are configuring FQDN over default VRF, you don't need to specify VRF name. |
Use the show running-config ntp command to see the ntp running configuration.
Router#show running-config ntp
ntp
server 10.48.59.212
!Use the show ntp associations command to verify that an NTP association has come up.
Router#show ntp associations
address ref clock st when poll reach delay offset disp
~10.48.59.212 173.38.201.67 2 42 128 3 196.06 -14.25 3949.4
* sys_peer, # selected, + candidate, - outlayer, x falseticker, ~ configuredOn devices that have hardware clocks (system calendars), you can configure the hardware clock to be periodically updated from the software clock. This is advisable for devices using NTP, because the time and date on the software clock (set using NTP) is more accurate than the hardware clock. The time setting on the hardware clock has the potential to drift slightly over time.
Note |
No specific command enables NTP; the first NTP configuration command that you issue enables NTP. |
| Command or Action | Purpose | |
|---|---|---|
|
Step 1 |
configure Example: |
Enters global configuration mode. |
|
Step 2 |
ntp Example: |
Enters NTP configuration mode. |
|
Step 3 |
update-calendar Example: |
Configures the router t o update its system calendar from the software clock at periodic intervals. |
|
Step 4 |
Use one of the following commands:
Example:or |
Saves configuration changes.
|
This task explains how to verify the status of NTP components.
Note |
The commands can be entered in any order. |
| Command or Action | Purpose | |
|---|---|---|
|
Step 1 |
show ntp associations [detail] [location node-id] Example: |
Displays the status of NTP associations. |
|
Step 2 |
show ntp status [location node-id] Example: |
Displays the status of NTP. |
The following is sample output from the show ntp associations command:
RP/0/RP0/CPU0:router# show ntp associations
Tue Oct 7 11:22:46.839 JST
address ref clock st when poll reach delay offset disp
*~192.168.128.5 10.81.254.131 2 1 64 377 7.98 -0.560 0.108
+~dead:beef::2 vrf testAA
171.68.10.80 3 20 64 377 6.00 -2.832 0.046
* sys_peer, # selected, + candidate, - outlayer, x falseticker, ~ configured
RP/0/RP0/CPU0:router# show ntp associations
address ref clock st when poll reach delay offset disp
+~127.127.1.1 127.127.1.1 5 5 1024 37 0.0 0.00 438.3
*~172.19.69.1 172.24.114.33 3 13 1024 1 2.0 67.16 0.0
* master (synced), # master (unsynced), + selected, - candidate, ~ configured
The following is sample output from the show ntp status command:
RP/0/RP0/CPU0:router# show ntp status
Tue Oct 7 11:22:54.023 JST
Clock is synchronized, stratum 3, reference is 192.168.128.5
nominal freq is 1000.0000 Hz, actual freq is 1000.2725 Hz, precision is 2**24
reference time is CC95463C.9B964367 (11:21:48.607 JST Tue Oct 7 2008)
clock offset is -1.738 msec, root delay is 186.050 msec
root dispersion is 53.86 msec, peer dispersion is 0.09 msec
loopfilter state is 'CTRL' (Normal Controlled Loop), drift is -0.0002724105 s/s
system poll interval is 64, last update was 66 sec ago
RP/0/RP0/CPU0:router# show ntp status
Clock is synchronized, stratum 4, reference is 172.19.69.1
nominal freq is 1000.0000 Hz, actual freq is 999.9988 Hz, precision is 2**26
reference time is C54C131B.9EECF6CA (07:26:19.620 UTC Mon Nov 24 2008)
clock offset is 66.3685 msec, root delay is 7.80 msec
root dispersion is 950.04 msec, peer dispersion is 3.38 msec
The following example shows an NTP configuration in which the router’s system clock is configured to form a peer association with the time server host at IP address 192.168.22.33, and to allow the system clock to be synchronized by time server hosts at IP address 10.0.2.1 and 172.19.69.1:
ntp
server 10.0.2.1
peer 192.168.22.33
server 172.19.69.1
The following example shows an NTP client configuration in which interface 0/2/0/0 is configured to receive NTP broadcast packets, and the estimated round-trip delay between an NTP client and an NTP broadcast server is set to 2 microseconds:
ntp
interface tengige 0/2/0/0
broadcast client
exit
broadcastdelay 2
The following example shows an NTP server configuration where interface 0/2/0/2 is configured to be a broadcast server:
ntp
interface tengige 0/2/0/2
broadcast
The following example shows an NTP multicast client configuration where 10-Gigabit Ethernet interface 0/1/1/0 is configured to be a multicast client and to join the default multicast group (IPv4 address 224.0.1.1):
ntp interface TenGigE 0/1/1/0
multicast client
The following example shows an NTP multicast server configuration where 10-Gigabit Ethernet interface 0/1/1/0 is configured to be a multicast server:
ntp interface TenGigE 0/1/1/0
multicast destination 224.0.1.1
The following example shows a NTP access group configuration where the following access group restrictions are applied:
Peer restrictions are applied to IP addresses that pass the criteria of the access list named peer-acl.
Serve restrictions are applied to IP addresses that pass the criteria of access list named serve-acl.
Serve-only restrictions are applied to IP addresses that pass the criteria of the access list named serve-only-acl.
Query-only restrictions are applied to IP addresses that pass the criteria of the access list named query-only-acl.
ntp
peer 10.1.1.1
peer 10.1.1.1
peer 10.2.2.2
peer 10.3.3.3
peer 10.4.4.4
peer 10.5.5.5
peer 10.6.6.6
peer 10.7.7.7
peer 10.8.8.8
access-group peer peer-acl
access-group serve serve-acl
access-group serve-only serve-only-acl
access-group query-only query-only-acl
exit
ipv4 access-list peer-acl
10 permit ip host 10.1.1.1 any
20 permit ip host 10.8.8.8 any
exit
ipv4 access-list serve-acl
10 permit ip host 10.4.4.4 any
20 permit ip host 10.5.5.5 any
exit
ipv4 access-list query-only-acl
10 permit ip host 10.2.2.2 any
20 permit ip host 10.3.3.3 any
exit
ipv4 access-list serve-only-acl
10 permit ip host 10.6.6.6 any
20 permit ip host 10.7.7.7 any
exit
The following example shows an NTP authentication configuration. In this example, the following is configured:
NTP authentication is enabled.
Two authentication keys are configured (key 2 and key 3).
The router is configured to allow its software clock to be synchronized with the clock of the peer (or vice versa) at IP address 10.3.32.154 using authentication key 2.
The router is configured to allow its software clock to be synchronized with the clock by the device at IP address 10.32.154.145 using authentication key 3.
The router is configured to synchronize only to systems providing authentication key 3 in their NTP packets.
ntp
authenticate
authentication-key 2 md5 encrypted 06120A2D40031D1008124
authentication-key 3 md5 encrypted 1311121E074110232621
trusted-key 3
server 10.3.32.154 key 3
peer 10.32.154.145 key 2
The following example shows an NTP configuration in which 0/2/0/0 interface is disabled:
ntp
interface tengige 0/2/0/0
disable
exit
authentication-key 2 md5 encrypted 06120A2D40031D1008124
authentication-key 3 md5 encrypted 1311121E074110232621
authenticate
trusted-key 3
server 10.3.32.154 key 3
peer 10.32.154.145 key 2
The following example shows an NTP configuration in which Ethernet management interface 0/0/CPU0/0 is configured as the source address for NTP packets:
ntp
authentication-key 2 md5 encrypted 06120A2D40031D1008124
authentication-key 3 md5 encrypted 1311121E074110232621
authenticate
trusted-key 3
server 10.3.32.154 key 3
peer 10.32.154.145 key 2
source MgmtEth0/0/CPU0/0
The following example shows a NTP configuration in which the router is configured to use its own NTP master clock to synchronize with peers when an external NTP source becomes unavailable:
ntp
master 6
The following example shows an NTP configuration in which the router is configured to update its hardware clock from the software clock at periodic intervals:
ntp
server 10.3.32.154
update-calendar
This task explains how to configure NTP server inside VRF interface.
Note |
No specific command enables NTP; the first NTP configuration command that you issue enables NTP. |
| Command or Action | Purpose | |||
|---|---|---|---|---|
|
Step 1 |
configure Example: |
Enters global configuration mode. |
||
|
Step 2 |
ntp Example: |
Enters NTP configuration mode. |
||
|
Step 3 |
vrf vrf-name Example: |
Specify name of a VRF (VPN- routing and forwarding) instance to configure. |
||
|
Step 4 |
source interface-type interface-instance Example: |
Configures an interface from which the IP source address is taken. This allows IOS-XR to respond to NTP queries on VRF interfaces, in this case the source is BVI.
|
||
|
Step 5 |
Use one of the following commands:
Example:or |
Saves configuration changes.
|
Feedback