About this Manual
Note
The terms "Unidirectional Path Switched Ring" and "UPSR" may appear in Cisco literature. These terms do not refer to using Cisco ONS 15xxx products in a unidirectional path switched ring configuration. Rather, these terms, as well as "Path Protected Mesh Network" and "PPMN," refer generally to Cisco's path protection feature, which may be used in any topological network configuration. Cisco does not recommend using its path protection feature in any particular topological network configuration.
This section explains the objectives, intended audience, and organization of this publication and describes the conventions that convey instructions and other information.
This section provides the following information:
•
Revision History
•
Document Objectives
•
Audience
•
Related Documentation
•
Document Conventions
•
Obtaining Optical Networking Information
•
Obtaining Documentation and Submitting a Service Request
Revision History
|
|
March 2007 |
Changed fuse rating and power consumption specifications in Appendix A. |
April 2007 |
Added server trail information in the "Virtual Concatenated Circuits" section in the "Circuits and Tunnels" chapter. |
July 2007 |
Modified "Caution" in the "Shelf Configuration" section of the "Electrical Cards" chapter. |
August 2007 |
Updated the note in the Path Protection Circuits section of the Circuits and Tunnels chapter. Added a paragraph on switch time for split fiber routing at the end of the "VCAT Member Routing" section of the "Circuits and Tunnels" chapter. |
September 2007 |
Updated About This Guide chapter. |
October 2007 |
Added information about Border Error Rates in Performance Monitoring chapter. |
November 2007 |
Added a note in the 1+1 Protection section, in the Card Protection chapter. |
April 2008 |
• Added a note in the User Password, Login, and Access Policies section in the Security chapter. • Updated note on protection switching in Link Capacity Adjustment section in Circuits and Tunnels chapter. |
May 2008 |
• Updated the table, Software and Hardware Compatibility—XC10G and XC-VXC-10G Configurations, in the Shelf and Backplane Hardware chapter. • Added power-level LED information for TCC2 and TCC2P cards in Common Control Cards chapter. |
July 2008 |
• Updated the section "15454_MRC-12 Port-Level Indicators" in the Optical Cards chapter, to show the correct number and status of the Rx indicator. • Added DS-3/EC1-48 card support for the EIA type MiniBNC in Table 1-2, Chapter 1, Shelf and Backplane Hardware. • Deleted the note in the Power and Ground Description section in Chapter 1, Shelf and Backplane Hardware. |
September 2008 |
• Added a note in Card Default Settings and Node Default Settings section of Appendix C, Network Element Defaults. • Added a Warning for all optical cards in Chapter 4, Optical Cards. • Updated FC_MR-4 Statistics Parameters table in the Chapter 15, Performance Monitoring. • Updated the Software and Hardware Compatibility section in Chapter 1 Shelf and Backplane Hardware. |
December 2008 |
• Updated the list of PM parameters for MRC-12 card in Chapter 15, Performance Monitoring. • Updated the UBIC-V and UBIC-H sections in Chapter 1, Shelf and Backplane Hardware. |
March 2009 |
Updated Table 1-17 and Table 1-20 in UBIC-V and UBIC-H sections in Chapter 1, Shelf and Backplane Hardware. |
June 2009 |
• Updated the Figure AEP Wire-Wrap Connections to Backplane Pins in Chapter 1, Shelf and Backplane Hardware. • Updated "OC-N Speed Upgrades" in Chapter 12, SONET Topologies and Upgrades. |
July 2009 |
• Updated Table 1-2 in Chapter 1, Shelf and Backplane Hardware. • Updated the "Common-Control Card Software Release Compatibility" table in the chapter 2, Common Control Cards. • Added a new section, Comparison of the Protection Schemes in the chapter, SONET Topologies and Upgrades. |
August 2009 |
• Updated the first footnote in the table titled ONS 15454 Software and Hardware Compatibility—XC10G and XC-VXC-10G Configurations in the chapter, Shelf and Backplane Hardware. • Added a caution in section DS3XM-12 Card of Chapter 3, Electrical Cards. |
November 2009 |
• Added a new section, SDH Tunneling in the chapter, Circuits and Tunnels. • Updated the table "Line Rate Configurations Per 15454_MRC-12 Port, Based on Available Bandwidth" in the chapter, "Optical Cards". |
February 2010 |
• Changed the BIEC parameter to BIT-EC in Chapter, "Performance Monitoring". |
April 2010 |
• Updated the section "SNMP Overview" in the chapter "SNMP". |
May 2010 |
• Updated the note in the section "DS3/EC1-48 Card" in the chapter "Electrical Cards". |
June 2010 |
Updated the caution in the section "DS1/E1-56 Card" in the chapter "Electrical Cards". |
August 2010 |
Updated the section "Bridge and Roll" in the chapter "Circuits and Tunnels". |
November 2010 |
Updated the figure "ML1000-2 Faceplate and Block Diagram" under the section "ML1000-2 Card" in the chapter "Ethernet Cards". |
June 2011 |
• Updated the section "AIC-I Card" in the chapter "Common Control Cards". • Updated the tables "ONS 15454 Software and Hardware Compatibility—XC and XCVT Configurations" and "ONS 15454 Software and Hardware Compatibility—XC10G and XC-VXC-10G Configurations" in the chapter "Shelf and Backplane Hardware". |
July 2011 |
• Added a note in the "PC and UNIX Workstation Requirements" section of Chapter, "Cisco Transport Controller Operation". • Updated the tables "DS3XM-6 Card PMs" and "DS3XM-12 Card PMs" in the chapter "Performance Monitoring". |
October 2011 |
Updated the section "AMP Champ EIA" in the chapter, "Shelf and Backplane Hardware". |
January 2012 |
Updated the privileges for the Download/Cancel operations in the table, "ONS 15454 SDH Security Levels—Network View " in the chapter, "Security". |
March 2012 |
• Updated the section "TCC2P Functionality" in the chapter, "Common Control Cards". • Updated the section "DS3/EC1-48 Card Specifications" in the appendix "Hardware Specifications". |
August 2012 |
The full length book-PDF was generated. |
Document Objectives
This manual provides reference information for the Cisco ONS 15454.
Audience
To use this publication, you should be familiar with Cisco or equivalent optical transmission hardware and cabling, telecommunications hardware and cabling, electronic circuitry and wiring practices, and preferably have experience as a telecommunications technician.
Related Documentation
Use the Cisco ONS 15454 Reference Manual with the following referenced publications:
•
Cisco ONS 15454 Procedure Guide
Provides procedures to install, turn up, provision, and maintain a Cisco ONS 15454 node and network.
•
Cisco ONS 15454 Troubleshooting Guide
Provides general troubleshooting procedures, alarm descriptions and troubleshooting procedures, error messages, and transient conditions.
•
Cisco ONS SONET TL1 Command Guide
Provides a full TL1 command and autonomous message set including parameters, AIDs, conditions and modifiers for the Cisco ONS 15454, ONS 15327, ONS 15600, ONS 15310-CL, and
ONS 15310-MA systems.
•
Cisco ONS SONET TL1 Reference Guide
Provides general information, procedures, and errors for TL1 in the Cisco ONS 15454, ONS 15327, ONS 15600, ONS 15310-CL, and ONS 15310-MA systems.
•
Ethernet Card Software Feature and Configuration G uide for the Cisco ONS 15454, Cisco ONS 15454 SDH, and Cisco ONS 15327
Provides software features for all Ethernet cards and configuration information for Cisco IOS on ML-Series cards.
•
Release Notes for the Cisco ONS 15454 Release 7.2
Provides caveats, closed issues, and new feature and functionality information.
For an update on End-of-Life and End-of-Sale notices, refer to http://www.cisco.com/en/US/products/hw/optical/ps2006/prod_eol_notices_list.html.
Document Conventions
This publication uses the following conventions:
|
|
boldface |
Commands and keywords in body text. |
italic |
Command input that is supplied by the user. |
[ ] |
Keywords or arguments that appear within square brackets are optional. |
{ x | x | x } |
A choice of keywords (represented by x) appears in braces separated by vertical bars. The user must select one. |
Ctrl |
The control key. For example, where Ctrl + D is written, hold down the Control key while pressing the D key. |
screen font |
Examples of information displayed on the screen. |
boldface screen font |
Examples of information that the user must enter. |
< > |
Command parameters that must be replaced by module-specific codes. |
Note
Means reader take note. Notes contain helpful suggestions or references to material not covered in the document.
Caution
Means
reader be careful. In this situation, the user might do something that could result in equipment damage or loss of data.
![](/c/dam/en/us/td/i/templates/warn.gif) |
Warning
|
|
IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071 SAVE THESE INSTRUCTIONS |
Waarschuwing |
BELANGRIJKE VEILIGHEIDSINSTRUCTIES Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen. BEWAAR DEZE INSTRUCTIES |
Varoitus |
TÄRKEITÄ TURVALLISUUSOHJEITA Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla. SÄILYTÄ NÄMÄ OHJEET |
Attention |
IMPORTANTES INFORMATIONS DE SÉCURITÉ Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la fin de chaque avertissement. CONSERVEZ CES INFORMATIONS |
Warnung |
WICHTIGE SICHERHEITSHINWEISE Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden. BEWAHREN SIE DIESE HINWEISE GUT AUF. |
Avvertenza |
IMPORTANTI ISTRUZIONI SULLA SICUREZZA Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento. CONSERVARE QUESTE ISTRUZIONI |
Advarsel |
VIKTIGE SIKKERHETSINSTRUKSJONER Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten. TA VARE PÅ DISSE INSTRUKSJONENE |
Aviso |
INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo. GUARDE ESTAS INSTRUÇÕES |
¡Advertencia! |
INSTRUCCIONES IMPORTANTES DE SEGURIDAD Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo. GUARDE ESTAS INSTRUCCIONES |
Varning! |
VIKTIGA SÄKERHETSANVISNINGAR Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning. SPARA DESSA ANVISNINGAR |
|
|
|
|
|
|
|
|
|
|
Aviso |
INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo. GUARDE ESTAS INSTRUÇÕES |
Advarsel |
VIGTIGE SIKKERHEDSANVISNINGER Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed. GEM DISSE ANVISNINGER |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Obtaining Optical Networking Information
This section contains information that is specific to optical networking products. For information that pertains to all of Cisco, refer to the Obtaining Documentation and Submitting a Service Request section.
Where to Find Safety and Warning Information
For safety and warning information, refer to the Cisco Optical Transport Products Safety and Compliance Information document that accompanied the product. This publication describes the international agency compliance and safety information for the Cisco ONS 15454 system. It also includes translations of the safety warnings that appear in the ONS 15454 system documentation.
Cisco Optical Networking Product Documentation CD-ROM
Optical networking-related documentation, including Cisco ONS 15xxx product documentation, is available in a CD-ROM package that ships with your product. The Optical Networking Product Documentation CD-ROM is updated periodically and may be more current than printed documentation.
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What's New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version 2.0. .