Manage Users and Roles

User Roles in Cisco ONP

Initially, the administrator performs access control management tasks, like activating users after user sign-up, creating user groups, roles, and assigning roles and users to user groups. The admin or user with admin access grants access to the newly created user by activating the user. After the admin grants access, the new user will be notified by email (sent to the email address registered while signing up). It is only then that the new user is able to log in. By default, the following user roles are available in Cisco ONP.

  1. Admin: The Admin user can create new user groups and assign user to user groups. Users are categorized into groups. There are certain predefined user groups in Cisco ONP. You cannot edit or delete these user groups. Admin can assign a group with a particular role. The role describes the actions that a particular user group can perform.

  2. Designer: The Designer user can design a network. There are two ways to design a network.

    • Manual Design

    • Import Design

    The designer user can create a network topology of any type (linear, ring, mesh) with Traffic, OLA, ROADM, and Passthrough sites, and assign the fibers with suitable spans between those sites. The designer can only design the network and cannot analyze the network. The designer can view the reports, when any user shares the analyzed network.

  3. Planner: The Planner user can design and analyze a network. After the Sites, Fiber spans, and Service demands are created, analyze the network to determine the network performance. Cisco ONP automatically optimizes the design and summarizes the optical transmission performance. In the analyzed state, all reports are available and updated. In the analyzed state, no aspect of the network design can be changed.

  4. Reader: The Reader user can view users, user groups, roles, and permission. The Reader can also view the network topology, layout, connections, and BOM. By default, a user is assigned in the READ_ONLY_GROUP with a READER_ROLE.

You can also create new roles. See Create a New Role.

Under Control Panel > Roles and Control Panel > Permissions, you can view the permissions applicable for each role and the actions that can be performed for each permission.

Grant Access to a New User

All users with Admin role receive an email notification about new user registration.

Before you begin

Log in to Cisco ONP Web Interface as a user with Admin role.

Procedure

Step 1

Click Control Panel.

The Access Control Management page appears.

Step 2

You can change the state of a user from INACTIVE to ACTIVE by using either of two ways:

  1. From the State field, click INACTIVE in the respective user row.

  2. Select the user row and click Update.

    • In the Update User dialog box, select the Group and State from the respective drop-down lists.

    • Click Save.

Step 3

Click OK in the Success dialog box.

Note

 

  • After the Admin grants access, the new user gets notified by email (sent to the email address registered while signing up). It is only then that the new user will be able to log in.

  • The admin assigns a newly created user with a Role and Group that determines what actions the user can perform.

Remove Access to a User

Use this task to remove Cisco ONP access to a user.

Before you begin

Log in to Cisco ONP Web Interface as a user with Admin role.

Procedure

Step 1

Click Control panel.

The Access Control Management page appears.

Step 2

You can change the state of a user from ACTIVE to INACTIVE by using either of two ways:

  1. From the State field, click ACTIVE in the respective user row.

  2. Select the user row and click Update.

    • In the Update User dialog box, select the Group and State from the respective drop-down lists.

    • Click Save.

Step 3

Click OK in the Success dialog box.

Delete a User

Use this task to delete a user.

Before you begin

Log in to Cisco ONP Web Interface as a user with Admin role.

Procedure

Step 1

Click Control panel.

The Access Control Management page appears.

Step 2

Select the user to be deleted under the USERS tab and click Delete.

Step 3

Click Yes in the Warning dialog box.

The message User deleted successfully appears. You can delete another user only after this message appears.

Create a New User Group

Use this task to create a new user group.

Before you begin

Log in to Cisco ONP Web Interface as a user with Admin role.

Procedure

Step 1

Click Control Panel.

The Access Control Management page appears.

Step 2

Click the USER GROUPS tab.

Step 3

Click Create.

Step 4

In the Create Group dialog box, enter the Group Name.

Step 5

Choose the appropriate role from the Role drop-down list. The available default roles are:

  • ADMIN

  • PLANNER

  • DESIGNER

  • READER

The Role drop-down list may also have user-defined roles that are listed under it.

Step 6

Click Save to save the created user group.

Step 7

Click OK in the Success dialog box.

Assign a User to a User Group

Use this task to assign a user to a user group.

Before you begin

Log in to Cisco ONP Web Interface as a user with Admin role.

Procedure

Step 1

Click Control panel.

The Access Control Management page appears.

Step 2

Under the USERS tab, select the user who is to be assigned to the new group.

Step 3

Click Update.

Step 4

In the Update User dialog box, perform the following:

  • Select the appropriate group from the Group drop-down list.

  • Select Active or Inactive from the State drop-down list, to activate or inactivate the user in the group, respectively.

  • Click Save.

Step 5

Click OK in the Success dialog box.

Note

 

  1. A user can belong to only one group.

  2. Only one role can be assigned to any group.

  3. All the users of a group have the same role as that of the group.

  4. By default, a new user is assigned to the Read_Only_Group.

Set Password Expiration for Individual User

Use this task to set the expiration of the password set by the user.

Before you begin

Log in to Cisco ONP Web Interface with Admin or Configuration_Management permission.

Procedure

Step 1

Click Control Panel.

The Access Control Management page appears.

Step 2

Select the user under the USERS tab.

Step 3

Click Update.

Step 4

In the Update User dialog box, click the PASSWORD EXPIRY tab.

Step 5

Enter values for the Lifetime, Warning and Grace fields.

Step 6

Click Save.

Note

 
The password expiry settings like lifetime, warning and grace time, take effect after the existing password is changed by the user.

Step 7

Click OK in the Success dialog box.

Set Password Expiration for All Users

Use this task to set the expiration of the password for all users.

Before you begin

Log in to Cisco ONP Web Interface with Admin or Configuration_Management permission.

Procedure

Step 1

Click Control Panel.

The Access Control Management page appears.

Step 2

Click the System Configuration tab.

Step 3

Enter values for the Lifetime, Warning and Grace fields.

Step 4

Click Update.

Note

 
The password expiry settings like lifetime, warning and grace time, take effect after the existing password is changed by the user.

Lock and Unlock an Individual User Account

Use this task to lock or unlock an individual user account.

Before you begin

Log in to Cisco ONP Web Interface as a user with Admin role.

Procedure

Step 1

Click Control Panel.

The Access Control Management page appears.

Step 2

Click the USERS tab.

Step 3

Select the user whose account you want to lock or unlock.

Step 4

Click Lock to lock the user account, or click Unlock to unlock the locked user account.

Note

 
The user of a locked account must contact the admin to unlock the user account.

Expire the Password Set by an Individual User

Use the following task to expire the password set by an individual user.

Before you begin

Log in to Cisco ONP Web Interface as a user with Admin role.

Procedure

Step 1

Click Control Panel.

The Access Control Management page appears.

Step 2

Click the USERS tab.

Step 3

Select the user whose password you want to expire.

Step 4

Click Expire.

Create a New Role

Use the following task to create a new role.

Before you begin

Log in to Cisco ONP Web Interface as a user with Admin role.

Procedure

Step 1

Click Control Panel.

The Access Control Management page appears.

Step 2

Click the ROLES tab.

Step 3

Click Create.

Step 4

In the Create Role dialog box, enter the Role Name and select the Permissions for the role.

Note

 

You can select more than one permission.

Step 5

Click Save.

Step 6

Click OK in the Success dialog box.

Assign a Role to a User Group

Use the following task to assign a new role to a user group.

Before you begin

Log in to Cisco ONP Web Interface as a user with Admin role.

Procedure

Step 1

Click Control Panel.

The Access Control Management page appears.

Step 2

Click the USER GROUPS tab.

Step 3

Select the user group whose role is to be updated.

Step 4

Click Update.

Step 5

In the Update Group dialog box, select the desired role from the Role drop-down list, and click Save.

Step 6

Click OK in the Success dialog box.

Manage Password Through Dictionary

If a password exists in the predefined list of passwords under the Content column, the dictionary rejects the new password set by the user. You must have Admin or Configuration_Management permission to view and modify the dictionary.

By default, the Rejection Mode toggle button is disabled. Enable the Rejection Mode toggle button to verify the password against dictionary. This password verification check against the dictionary happens during any one of the following events:

  • New user sign-up

  • Password change

  • Password reset using forgot password option

The following is the procedure to verify, whether the new password set by the user exists in the list of predefined passwords:

Before you begin

Log in to Cisco ONP Web Interface as a user with Admin role.

Procedure

Step 1

Click Control Panel.

The Access Control Management page appears.

Step 2

Click the DICTIONARY tab.

Step 3

Enter the password in the Enter Passphrase text box.

Step 4

(Optional) Enter the limit (maximum number of matching passphrases) in the Enter Limit text box.

Step 5

Click Search.

The matching passphrases get displayed.

Note

 
If you have entered the limit, a number of search results matching the limit gets displayed. Otherwise, all matching passphrases get displayed.

Retrieve System Logs

The System Logs page shows at logs the events that are initiated during a specific time interval. See Logs.

Before you begin

Log in to Cisco ONP Web Interface as an admin or a user with User Management and Network Management permission.

Procedure

Step 1

Click Logs.

Step 2

Click Select Start Date, and choose the start date. Similarly, click Select End Date, and choose the end date.

Step 3

Click FILTER to retrieve the logs.

The following icons are available in the System Logs page:

Icons

Description

Export as CSV

Exports the system logs to an Excel sheet

Export Archive

Exports the system logs as a zip file

Import Archive

Imports the zip file

Refresh

Refreshes the system logs page

Clear Logs

Deletes the existing logs