OTNXC encryption
|
The OTNXC operating mode on the 400G-XP-LC card supports encryption.
|
Cisco NCS 2000 Series Line Card Configuration Guide
NTP-G367 Provisioning Encryption on 400G-XP-LC Card
|
Third party certificates for encryption
|
The 400G-XP-LC card supports the generation of a Certificate Signing Request (CSR) and the installation of Locally Significant
Certificates (LSCs) that can be used to authenticate the peer card connection. Third party certificates also referred to as
Locally Significant Certificates (LSCs) are certificates that are signed by a Certification Authority (CA) other than Cisco
Certificate Authority. LSCs allow customers to have their own Public Key Infrastructure (PKI) to provide better security,
to have control of their own CA, and to define policies, restrictions, and usages on the generated certificates.
|
Cisco NCS 2000 Series Line Card Configuration Guide
NTP-G363 Provisioning LSC on Cards
|
ANS APC Skipping
|
The upgraded NE update XML file imported on the CTC for the respective node will import the new ANS parameters and settings
for the new degree or modules. The existing ANS parameters or module settings are not affected. This prevents unintended changes
to the APC corrections to the existing degree and its associations.
|
Cisco NCS 2000 Series Network Configuration Guide
Automatic Node Setup
|
TNCS-2 and TNCS-2-O Control Cards
|
The TNCS-2 and TNCS-2O are new control cards compatible with all chassis types such as, Cisco NCS 2002, Cisco NCS 2006, and
Cisco NCS 2015.
|
Cisco NCS 2000 Series Control Card and Node Configuration Guide
TNCS 2 and TNCS 2O Cards
|
TNCS-O Card Support
|
The TNCS-O card is supported on the NCS 2002.
|
Cisco NCS 2000 Series Control Card and Node Configuration Guide
TNCS-O Card
|
400G-XP-LC enhancements
|
-
The new payloads supported for the MXP operating mode are FC-10G, FC-8G, and 40G.
-
The OPM_2x40G_2x10G slice mode can be configured in the MXP operating mode for 40GE payloads.
-
LLDP support—The source MAC address of 10 or 100GE ports can be retrieved after an LLDP packet is received on the client port.
LLDP filtering is enabled or disabled on the 10GE or 100GE ports using the Provisioning > Line > Ethernet tab in CTC.
|
Cisco NCS 2000 Series Line Card Configuration Guide
400G-XP-LC Card
|
NCS 1004 Alien
|
Two variants of 300G , such as 300G_3bps and 300G_3.4375bps are added in the wavelength drop-down list.
|
Cisco NCS 2000 Series Network Configuration Guide
DLP-G800 Create an LMP Link Using CTC
|
8QAM Support on non-SSON
|
In non-SSON, the user can force the wavelength by checking the wavelength configuration check box and choosing the wavelength
from the drop-down list.
|
Cisco NCS 2000 Series Network Configuration Guide
Provision GMPLS Optical Channel Network Connections Using Non-SSON
|
OTDR Support for TNCS-2O Cards
|
A TNCS-2O card has an optical module that provides Optical Time Domain Reflectometer (OTDR) measurement, ORL measurement,
and standard Optical Service Channel (OSC) capability on two ports. These capabilities are available for upto four ports for
each shelf; one shelf can have two TNCS-2O cards.
|
Cisco NCS 2000 Series Network Configuration Guide
Manage the Node
|
Regenerator Constraints Support
|
For using a regenerator, the optical path needs to be validated. If the optical validation fails, then, the regenerator cannot
be used, and the circuit creation fails. If validation is not supported, pre-validated paths are calculated offline and provided
as a constraint to the control plane, while setting up the main and restored paths.
|
Cisco NCS 2000 Series Network Configuration Guide
|