Release Notes for VDSL CPE PHY Release A2pv6C039k

Available Languages

Download Options

  • PDF     (191.3 KB)
    View with Adobe Reader on a variety of devices
Updated:November 6, 2014

Bias-Free Language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

Table of Contents

Release Notes for VDSL CPE PHY R eleas e A2pv6C039k

Contents

Introduction

System Requirements

Memory and IOS Software Requirements

Determining the Firmware Version

Upgrading to a New Firmware Release

New and Changed Information

Related Documentation

Release-Specific Documents

Platform-Specific Documents

Other Firmware Code

Obtain Documentation and Submit a Service Request

Release Notes for VDSL CPE PHY Release A2pv6C039k

First Published: November 06, 2014

Release: Cisco IOS Release 15.2(4)M

Contents

Introduction

These release notes describe new enhancements and fixed caveats for the VDSL CPE PHY using firmware release A2pv6C039k.

These release notes are updated as needed.

System Requirements

Memory and IOS Software Requirements

Table 1 lists the supported Cisco 880 Series Routers and Cisco 890 Series Routers with their respective memory and IOS requirements while using firmware release A2pv6C039k.

Note This firmware version is compiled with the SDK version 4.02L.03 and supports IOS release 15.6(2)T and earlier releases up to the supported version mentioned in the firmware release note. This firmware is not supported with Cisco IOS 15.6(3)M and later releases.

Table 1 Supported Cisco 880 Routers and Cisco 890 Routers with Memory Requirements
Platform
Flash (MB)
DRAM (MB)
IOS version

Cisco 880 VA Series Routers

256

512

15.2(4) M or later

Cisco 890 VA Series Routers

256

512

15.2(4) M or later

The following EHWICs are supported with A2pv6C039k:

  • C1900/C2900/C3900/C3900e Series router with EHWIC-VA-DSL-A
  • C1900/C2900/C3900/C3900e Series router with EHWIC-VA-DSL-M

Determining the Firmware Version

To determine the version of firmware currently running on your Cisco 880VA Series Router, issue the following IOS command and look for the output entries shown in bold in this example:

 
C887VA# show controller vdsl 0
Controller VDSL 0 is UP
 
Daemon Status: Up
 
XTU-R (DS) XTU-C (US)
Chip Vendor ID: 'BDCM' 'BDCM'
Chip Vendor Specific: 0x0000 0xA1F3
Chip Vendor Country: 0xB500 0xB500
Modem Vendor ID: 'CSCO' ' '
Modem Vendor Specific: 0x4602 0x0000
Modem Vendor Country: 0xB500 0x0000
Serial Number Near: FTX162586PX C887VA-C 15.2(4)M
Serial Number Far:
Modem Version Near: 15.2(4)M
Modem Version Far: 0xa1f3
 
Modem Status: TC Sync (Showtime!)
DSL Config Mode: AUTO
Trained Mode: G.992.5 (ADSL2+) Annex A
TC Mode: ATM
Selftest Result: 0x00
DELT configuration: disabled
DELT state: not running
Trellis: ON ON
SRA: disabled disabled
SRA count: 0 0
Bit swap: enabled enabled
Bit swap count: 8 0
Line Attenuation: 7.0 dB 6.1 dB
Signal Attenuation: 5.1 dB 5.2 dB
Noise Margin: 9.6 dB 17.0 dB
Attainable Rate: 23336 kbits/s 945 kbits/s
Actual Power: 13.5 dBm 12.0 dBm
Total FECC: 0 0
Total ES: 0 0
Total SES: 0 0
Total LOSS: 0 0
Total UAS: 1767318 1767318
Total LPRS: 0 0
Total LOFS: 0 0
Total LOLS: 0 0
 
Full inits: 1
Failed full inits: 7
Short inits: 0
Failed short inits: 214
 
Firmware Source File Name (version)
-------- --------- ------------------
VDSL user config flash:VA_A_39k_B_38h3_24h.bin (10)
 
 
Modem FW Version: 140613_1141-4.02L.03.A2pv6C039k.d24h
Modem PHY Version: A2pv6C039k.d24h
Vendor Version: Ap6v39k.24h 68
 
DS Channel1 DS Channel0 US Channel1 US Channel0
Speed (kbps): 0 20525 0 945
SRA Previous Speed: 0 0 0 0
Previous Speed: 0 0 0 0
Total Cells: 0 5425453 0 245316
User Cells: 0 0 0 0
Reed-Solomon EC: 0 0 0 0
CRC Errors: 0 0 0 0
Header Errors: 0 0 0 0
Interleave (ms): 0.00 8.26 0.00 15.00
Actual INP: 0.00 2.08 0.00 2.00
 
Training Log : Stopped
Training Log Filename : flash:vdsllog.bin
 
C887VA#

Upgrading to a New Firmware Release

Perform the following steps to upgrade to a new firmware release:

1. Download the new firmware from Cisco.com Software Center at: http://www.cisco.com/cisco/software/navigator.html

Choose Products -> Routers -> Branch Routers -> Cisco 800 Series Routers -> Cisco 880VA Integrated Services Router (or Cisco 890 VA Integrated Services Router) -> Very High Bitrate DSL (VDSL) Firmware > A2pv6C039k

2. Copy the A2pv6C039k firmware to a designated location; for example, router flash or a TFTP server.

3. Configure the router to load the new firmware from a designated location.

Router# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
 
Router(config)# controller vdsl 0
Router(config-controller)# firmware filename ?
archive: Download fw file name
cns: Download fw file name
flash: Download fw file name
ftp: Download fw file name
http: Download fw file name
https: Download fw file name
null: Download fw file name
nvram: Download fw file name
rcp: Download fw file name
scp: Download fw file name
system: Download fw file name
tar: Download fw file name
tftp: Download fw file name
tmpsys: Download fw file name
xmodem: Download fw file name
ymodem: Download fw file name
 
Router(config-controller)# firmware filename flash:

Note Controller VDSL 0 should not be turned off.

4. Enter the copy running-config startup-config command to save your configuration.

5. Enter the reload command to restart the router.

New and Changed Information

This section contains changes introduced with firmware release A2pv6C039k.

  • Fixed issues with G.993.2 US SRA in G.INP
  • Fixed training issues in G.992.1 when DS G.HS PSD are below nominal
  • Fixed ATTNDR reporting issue in G.993.2 Showtime
  • Fixed error sample reporting in G.Vector
  • Improved BER performance of G.992.[35] in bridged tap loops
  • Improved G.992.1 performance against ECI Anaconda

Known Issues and Limitations

  • G.INP supports DTU framing type 1 only
  • G.993.2 ATM mode testing is limited due to lack of DSLAM support

Related Documentation

Platform-Specific Documents

For more information about the supported platforms, see the following documentations:

Other Firmware Code

For information on the firmware used prior to this release, see Release Notes for Cisco 860VA Series Multimode VDSL2/ADSL2/2+ DSL Router with Firmware Release A2pv6F039d.

Obtain Documentation and Submit a Service Request

For information on obtaining documentation, using the Cisco Bug Search Tool (BST), submitting a service request, and gathering additional information, see What’s New in Cisco Product Documentation.

To receive new and revised Cisco technical content directly to your desktop, you can subscribe to the  What’s New in Cisco Product Documentation RSS feed. The RSS feeds are a free service.

This document is to be used in conjunction with the documents listed in the “Related Documentation” section.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1721R)

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.

© 2014 Cisco Systems, Inc. All rights reserved.

Was this Document Helpful?

FeedbackFeedback

Contact Cisco

This Document Applies to These Products