Configuring MPLS Layer 2 VPNs

First Published: March 29, 2012

Lasted Revised:

The Frame Relay to ATM Bridged Interworking feature provides interoperability between the Frame Relay attachment virtual circuit (VC) and the ATM attachment VC that are connected to different provider edge (PE) routers. The bridged encapsulation corresponding to the bridged (Ethernet) interworking mechanism is used to enable this interoperability. The Ethernet frames are carried through the MPLS network using Ethernet over MPLS (EoMPLS). The interworking function is performed in the PE routers connected to the Frame Relay attachment VC and the ATM attachment VC based on RFC 2684 and RFC 2427.

The xconnect support on Gigabit EtherChannel (GEC) Virtual Private Wire Service (VPWS) on ASR 1000 feature enables service providers to supply connectivity between customer sites with existing data link layer (Layer 2) networks by using a single, integrated, packet-based network infrastructure—a Cisco MPLS network. Instead of separate networks with separate network management environments, service providers can deliver Layer 2 connections over an MPLS backbone.

Layer 2 Gateway Protocol (L2GP) is a recommended IEEE standard (802.1ah) to address the issues that arise when two independent, bridged domains are connected redundantly through an arbitrary number of links. L2GP defines how the forwarding gateways are selected, so that only redundant ports are blocked and there are no temporary loops. The transition should be at least at the same speed in which Spanning Tree Protocol (STP) L2GP resolves the transient loop problem during reconvergence because it does not require cooperation from the outside domain.

Reverse Layer 2 Gateway Protocol (R-L2GP) is a variation of an L2GP. In case of an R-L2GP, the pseudo information of the R-L2GP is transmitted by network provider edges (nPEs) instead of user provider edges (uPEs). R-L2GP provides a mechanism to send out static preconfigured bridge protocol data units (BPDUs) on each ring access port of the nPEs to stimulate a per-access ring instantiation of the protocol. R-L2GP enables the PEs to avoid the burden of running Multiple Instances Spanning Tree Protocol (MISTP) when multiple independent access networks that run MISTP connect to a pair of redundant PEs.

High-Level Data Link Control (HDLC) Ethernet over MPLS is part of the Any Transport over MPLS (AToM) solution. HDLC and Ethernet are two link-layer transports that utilize the AToM architecture.

Overview of L2VPN Interworking

Interworking is a transforming function that interconnects two heterogeneous attachment circuits (ACs). Several types of interworking functions exist. The function that is used depends on the AC type used, the type of data carried, and the level of functionality required. The two main Layer 2 Virtual Private Network (L2VPN) interworking functions supported in Cisco IOS XE software are bridged interworking and routed interworking.

Layer 2 (L2) transport over multiprotocol label switching (MPLS) and IP exists for ACs, such as Ethernet-to-Ethernet or Point-to-Point Protocol (PPP), Ethernet to VLAN, and Ethernet to Frame Relay. An interworking function facilitates translation between different L2 encapsulations.

L2VPN Interworking Modes

L2VPN interworking works in either Ethernet (bridged) mode or IP (routed) mode. You can specify the mode by issuing the interworking {ethernet | ip} command in pseudowire-class configuration mode and in L2VPN xconnect configuration mode for protocol-based CLI.

The interworking command causes the ACs to be terminated locally. The two keywords perform the following functions:

  • The ethernet keyword causes Ethernet frames to be extracted from an AC and sent over the pseudowire. Ethernet end-to-end transmission is resumed. The AC frames that are not Ethernet are dropped. In the case of VLAN, the VLAN tag is removed, leaving an untagged Ethernet frame.
  • The ip keyword causes IP packets to be extracted from an AC and sent over the pseudowire. The AC frames that do not contain IPv4 packets are dropped.

The following sections explain the Ethernet and IP interworking modes in detail.

Ethernet or Bridged Interworking

Ethernet interworking is also called bridged interworking. Ethernet frames are bridged across the pseudowire. The CE routers can natively bridge Ethernet traffic or can route traffic using a bridged encapsulation model, such as Bridge-group Virtual Interface (BVI) or Routed Bridge Encapsulation (RBE). The PE routers operate in the Ethernet like-to-like mode.

The Ethernet interworking mode offers the following services:

  • LAN services—An example of this is an enterprise that has several sites, with some sites having Ethernet connectivity to the service provider (SP) network and others having Asynchronous Transfer Mode (ATM) connectivity. If the enterprise requires LAN connectivity to all its sites, traffic from the Ethernet or VLAN of one site can be sent through the IP/MPLS network and encapsulated as bridged traffic over an ATM VC of another site.
  • Connectivity services—An example of this is an enterprise that has different sites running an Internal Gateway Protocol (IGP) that has incompatible procedures on broadcast and non broadcast links. This enterprise has several sites that run an IGP, such as Open Shortest Path First (OSPF) or Intermediate System-to-Intermediate System (IS-IS), between the sites. In this scenario, some of the procedures (such as route advertisement or designated router election) depend on the underlying L2 protocol and are different for a point-to-point ATM connection versus a broadcast Ethernet connection. Therefore, the bridged encapsulation over ATM can be used to achieve homogenous Ethernet connectivity between the CE routers running an IGP.

IP or Routed Interworking

IP interworking is also called routed interworking. The CE routers encapsulate the IP on the link between the CE router and the PE router. A new VC type is used to signal the IP pseudowire in MPLS. Translation between the L2 and IP encapsulations across the pseudowire is required. Special consideration needs to be given to the address resolution protocol operation and routing protocol operation, because these are handled differently on different L2 encapsulations.

The IP interworking mode is used to provide IP connectivity between sites, regardless of the L2 connectivity to these sites. It is different from a Layer 3 VPN because it is point-to-point in nature and the service provider does not maintain any routing information pertaining to customers.

Address resolution is encapsulation dependent as specified here:

  • Ethernet uses Address Resolution Protocol (ARP)
  • ATM uses inverse ARP
  • PPP uses IP Control Protocol (IPCP)
  • HDLC uses Serial Line ARP (SLARP)

Therefore, address resolution must be terminated on the PE router. Also, the end-to-end address resolution is not supported. Routing protocols operate differently over broadcast and point-to-point media. For Ethernet, the CE routers must either use static routing or configure the routing protocols to treat the Ethernet side as a point-to-point network.

In routed interworking, the IP packets that are extracted from the ACs are sent over the pseudowire. The pseudowire works in the IP Layer 2 transport (VC type 0x000B) like-to-like mode. The interworking function at the network service provider's (NSP) end completes the required adaptation based on the AC technology. The non-IPv4 packets are dropped.

In routed interworking, the following considerations must be kept in mind:

  • ARP, inverse ARP, and IPCP are punted to the routing protocol.

Therefore, the PE router at the NSP end must provide the following address-resolution functionalities for the Ethernet and ATM and Frame Relay point-to-point subinterface attachment circuits:

    • Ethernet—The PE device acts as a Proxy ARP server to all the ARP requests from the CE router. The PE router responds with the MAC address of its local interface.
    • ATM and Frame Relay point-to-point subinterface—By default, inverse ARP does not run in the point-to-point Frame Relay or ATM subinterfaces. The IP address and subnet mask define the connected prefix; therefore, configuration is not required in the CE devices.
  • Interworking requires that the MTUs in both the ACs must match for the pseudowire that is to come up. The default MTU in one AC must match the MTU of other AC.

The following table lists the range of MTUs that can be configured for different ACs.

Table 1. Range of MTUs for Different ACs

AC Type

Range of MTUs{start superscript}1{end superscript} Supported

ATM

64 to 9216

Gigabit Ethernet

1500 to 9216

POS

64 to 9216

Fast Ethernet

1500 to 9216

{start footnote}The MTU configured on an AC must not exceed the MTU in the core network. This ensures that the traffic is not fragmented.{end footnote}

  • The CE routers with Ethernet attachment VCs running OSPF must be configured with the ospfIfType option so that the OSPF protocol treats the underlying physical broadcast link as a P2P link.

Virtual Private LAN Services

Virtual Private LAN Service (VPLS) enables enterprises to link together their Ethernet-based LANs from multiple sites via the infrastructure provided by their service provider. From the enterprise perspective, the service provider's public network looks like one giant Ethernet LAN. For the service provider, VPLS provides an opportunity to deploy another revenue-generating service on top of their existing network without major capital expenditures. Operators can extend the operational life of equipment in their network.

Virtual Private LAN Services (VPLS) uses the provider core to join multiple attachment circuits together to simulate a virtual bridge that connects the multiple attachment circuits together. From a customer point of view, there is no topology for VPLS. All of the CE devices appear to connect to a logical bridge emulated by the provider core.

Reverse Layer 2 Gateway Protocol

Layer 2 Gateway Protocol (L2GP) is a recommended IEEE standard (802.1ah) to address the issues that arise when two independent, bridged domains are connected redundantly through an arbitrary number of links. L2GP defines how the forwarding gateways are selected, so that only redundant ports are blocked and there are no temporary loops. The transition should be at least the same speed in which STP L2GP resolves the the transient loop problem during the reconvergence because it does not require cooperation from the outside domain.

Reverse Layer 2 Gateway Protocol (R-L2GP) is a variation of an L2GP. In case of an R-L2GP, the pseudo information of the R-L2GP is transmitted by Network-facing Provider Edges (nPEs) instead of User Provider-Edges (uPEs). R-L2GP provides a mechanism to send out static preconfigured Bridge Protocol Data Units (BPDUs) on each ring access port of nPEs to stimulate a per-access ring instantiation of the protocol. R-L2GP enables the Provider Edges (PEs) to avoid the burden of running Multiple Instance Spanning Tree Protocol (MST) when multiple independent access networks that run MST connect to a pair of redundant PEs.

In order for this to work, the pair of nPEs are programmed to send out BPDUs on the access ring ports in such a way that they appear to be either:

  • The root bridge itself (the bridge with the lowest bridge ID or priority).
  • The bridge with the second lowest bridge ID or priority, and with a 0 cost path to the root.

Using R-L2GP, you can statically configure the BPDUs instead of the STP generate the BPDUs dynamically.

The following figure shows the topology of multiple-access networks connected to redundant nPEs.

Figure 1. Multiple-Access Networks Connected to Redundant nPEs

BPDUs Sent Out of R-L2GP Ports

An R-L2GP module in a route processor (RP) generates static preconfigured BPDUs, and sends them to uPEs via access ports, with the R-L2GP enabled.


Note
Only localy generated static BPDUs can be sent out to RL2GP ports.

The following figure shows how a BPDU is forwarded to an R-L2GP port.

Figure 2. BPDU on an R-L2GP Port

BPDUs Received on R-L2GP Ports

On PE, only BPDUs with Topology Change Notification (TCN) bits on are punted to the R-L2GP and the STP module. If the PE is in a redundant setting, the corresponding BPDUs are is propagated to peer-redundant PE via the L2 protocol forwarding pseudowire (PW).

BPDUs Received on L2 Protocol Forwarding PW

The TCN BPDUs received from L2 protocol forwarding PW are punted to RP, and STP/R-L2GP process it and generate MAC flush.

Restrictions for R-L2GP

The restrictions for the R-L2GP feature are:

  • R-L2GP is supported only on L2 bridge ports, and is not compatible with prestandard MST.
  • All the access-side shall have the same MST instance, the same name and the same revision number configuration as nPEs.
  • There is no configure error detection and recover mechanism for R-L2GP. Users are expected to configure R-L2GP and MSTP instance on CEs and nPEs correctly.

Configuring the R-L2GP

Since the R-L2GP configuration is bundled with the MST configuration, the above parameters can be recycled from the MSTI and MST region (currently only one MST region is supported on IOS) configurations. This section describes how to configure Reverse L2GP. It consists of the following sections:

Configuring the MST

Configuration of the MST must be done before configuring the R-L2GP and attaching the R-L2GP to a port.

SUMMARY STEPS

  1. enable
  2. configure terminal
  3. spanning-tree mode mst
  4. spanning-tree mst configuration
  5. name name
  6. revision version
  7. instance instance-id {vlans vlan-range}

DETAILED STEPS

  Command or Action Purpose

Step 1

enable

Example:

Router# enable

Enables privileged EXEC mode.

Enter your password if prompted.

Step 2

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3

spanning-tree mode mst

Example:

Router(config)# spanning-tree mode mst.

Enables MST mode.

Step 4

spanning-tree mst configuration

Example:

Router(config)# spanning-tree mst configuration

Enters MST configuration submode.

Step 5

name name

Example:

Router(config-mst)# name Cisco

Sets the name of the MST region.

Note

 
All the nodes in the same region should be configured with the same MST name.

Step 6

revision version

Example:

Router(config-mst)# revision  5

Sets the revision number for the MST (802.1s) configuration.

Note

 
All the nodes in the same region should be configured with the same MST configure revision number.

Step 7

instance instance-id {vlans vlan-range}

Example:

Router(config-mst)# instance 2 vlans 1-100

Maps a VLAN or a group of VLANs to an MST instance.

Configuring an R-L2GP Instance

Perform the following steps to configure R-L2GP instance.

SUMMARY STEPS

  1. enable
  2. configure terminal
  3. spanning-tree pseudo-information transmit indentifier
  4. remote-id id
  5. mst region-id root mac-address
  6. mst region-id cost

DETAILED STEPS

  Command or Action Purpose

Step 1

enable

Example:
Router> enable

Enables privileged EXEC mode.

Enter your password, if prompted.

Step 2

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3

spanning-tree pseudo-information transmit indentifier

Example:

Router(config)# spanning-tree pseudo-information transmit 46

Configures the Reverse-L2GP configuration on the interface or the untagged Ethernet Flow Point (EFP) port.

Step 4

remote-id id

Example:

Router(config-pseudo)# remote-id 53

Configures the remote R-L2GP instance ID that pairs with the specified R-L2GP instance ID.

Step 5

mst region-id root mac-address

Example:

Router(config-pseudo)# 
mst 0 root 32768 0000.0000.0001

Adds MST instances to R-L2GP instances and configures the MAC address and priority for MST instances.

Note

 
MST 0 has all the VLANs that have not been explicitly specified in other MST instances. MST 0 must be configured for each R-L2GP instance.

Step 6

mst region-id cost

Example:

Router(config-pseudo)# mst 1 cost 1

Adds the corresponding MST instance list to the R-L2GP instance and configures the R-L2GP path cost for the MST instance or multiple MST instances.

What to do next

Note
To configure an R-L2GP on the Cisco ASR 1000 Series Aggregation Services Router, the remote-id configured on nPE1 must be the transmit identifier configured on nPE2, and vice versa.

Attaching an R-L2GP Instance to a Port

SUMMARY STEPS

  1. enable
  2. configure terminal
  3. interface gigabitethernet slot/port
  4. spanning-tree pseudo-information transmit identifier

DETAILED STEPS

  Command or Action Purpose

Step 1

enable

Example:
Router> enable

Enables privileged EXEC mode.

Enter your password, if prompted.

Step 2

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3

interface gigabitethernet slot/port

Example:

or
Example:

interface tengigabitethernet slot/port
Example:

Router(config)# interface gigabitethernet 4/1

Specifies Gigabit Ethernet or the 10 Gigabit Ethernet interface on the access side of the nPE to configure.

Here:

  • slot/port—Specifies the location of the interface.

Step 4

spanning-tree pseudo-information transmit identifier

Example:

Router(config-if)# spanning-tree pseudo-information transmit 46

Configures the Reverse-L2GP configuration on the interface.

Note

 
The identifier should be the same as the one configured on the nPE.

Example: Configuring an R-L2GP

The following example shows how to configure an R-L2GP in a network comprising two nPEs.

Configuration example on nPE1: 


enable
configure terminal
spanning-tree pseudo-information transmit 46
  remote-id 53
  mst 0 root 32768 0000.0000.0001
  mst 1 root 32768 0000.0000.0002
  mst 1 cost 1
  mst 2 root 32768 0000.0000.0003
exit
interface gigabitEthernet 2/1/0
   spanning-tree pseudo-information transmit 46

Configuration example on nPE2: 


spanning-tree pseudo-information transmit 53
  remote-id 46
  mst 0 root 32768 0000.0000.0001
  mst 1 root 32768 0000.0000.0002
  mst 1 cost 1
  mst 2 root 32768 0000.0000.0003
interface gigabitEthernet 0/0/1
   spanning-tree pseudo-information transmit 53

Configuring the Layer 2 Protocol Forwarding Virtual Private LAN Services Pseudowire Between Two Redundant NPES

SUMMARY STEPS

  1. enable
  2. configure terminal
  3. l2 vfi vfi-name manual
  4. vpn id vpn_id
  5. bridge-domain bridge_id
  6. forward permit l2protocol all
  7. neighbor ip-address vc-id {encapsulation mpls |pw-class pw-class-name }

DETAILED STEPS

  Command or Action Purpose

Step 1

enable

Example:
Router> enable

Enables privileged EXEC mode.

Enter your password, if prompted.

Step 2

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3

l2 vfi vfi-name manual

Example:

Router(config)# l2 vfi vfitest1 manual

Creates a Layer 2 Virtual Forwarding Instance (VFI) and enters the Layer 2 VFI manual configuration submode.

Step 4

vpn id vpn_id

Example:

Router(config-vfi)# vpn id 303

Sets or updates a VPN ID on a VPN routing and forwarding (VRF) instance.

Step 5

bridge-domain bridge_id

Example:

Router(config-vfi)# bridge-domain 100

Binds a service instance to a bridge domain instance.

Step 6

forward permit l2protocol all

Example:

Router(config-vfi)# forward permit l2protocol all

Defines the VPLS pseudowire that is used to transport bridge protocol data unit (BPDU) information between two network provider edge (N-PE) routers.

Step 7

neighbor ip-address vc-id {encapsulation mpls |pw-class pw-class-name }

Example:

Router(config-vfi)# neighbor 10.10.10.10 1 encapsulation mpls

Specifies the routers that should form a point-to-point Layer 2 virtual forwarding interface (VFI) connection.

Verifying an R-L2GP Configuration

The following examples show how to use the show commands to verify an R-L2GP configuration: 


Router# show spanning-tree pseudo-information 46 configuration
 
remote_id 53
 mst_region_id 0, port_count 2, update_flag 0x0
 mrecord 0x3AF841EC, mrec_count 3:
      msti 0: root_id 32768.0000.0000.0001, root_cost 0, update_flag 0x0
      msti 1: root_id 32769.0000.0000.0002, root_cost 1, update_flag 0x0
      msti 2: root_id 32770.0000.0000.0003, root_cost 0, update_flag 0x0
Router# show spanning-tree pseudo-information 1 interface GigabitEthernet3/0/3
Pseudo id 1:
        GigabitEthernet 2/1/0
        GigabitEthernet 0/0/1

Prerequisites for Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking

Before you configure the Frame Relay Data Link Connection Identifier (DLCI)-to-ATM AAL5SNAP Bridged Interworking feature on a router, ensure that the following prerequisites are met:

  • Enable frame-relay switching on the Frame Relay provider edge (PE) router.
  • Customer edge (CE) routers must support Bridge-group Virtual Interface or Routed Bridge Encapsulation.

Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking

This feature provides interoperability between the ATM attachment VC and Frame Relay attachment VC connected to different PE routers. This interworking uses the bridged encapsulation corresponding to the bridged (Ethernet) interworking mechanism. The Ethernet frames are carried through the MPLS network using Ethernet over MPLS (EoMPLS). This feature is configured only in the bridged mode and not in the routed mode.

The following figure shows the interworking function performed in the PE routers that are connected to the ATM attachment VC and the Frame Relay attachment VC.

Figure 3. Network Topology for Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking

On the ATM PE router with interworking function, when traffic flows from the ATM segment to MPLS cloud, the bridged encapsulation (ATM and SNAP header) is discarded and the Ethernet frame is encapsulated with the labels required to go through the pseudowire using the VC type 5 (Ethernet). In the opposite direction, after the label disposition from the MPLS cloud, the Ethernet frames are encapsulated over AAL5SNAP using bridged encapsulation.

On the FR PE router with interworking function, when traffic flows from the FR segment to the MPLS cloud, the bridged encapsulation (Frame Relay and SNAP header) is discarded and the Ethernet frame is encapsulated with the labels required to go through the pseudowire, using the VC type 5 (Ethernet). In the opposite direction, after the label disposition from the MPLS cloud, the Ethernet frames are encapsulated over FR using bridged encapsulation.

The PE router automatically supports translation of both Cisco and IETF Frame Relay encapsulation types coming from the Customer edge (CE) router, but translates only to IETF when sending to the CE router. The Cisco CE router can handle the IETF encapsulation on receipt, even if it is configured to send Cisco encapsulation.

The following modes are supported:

  • The ATM permanent virtual circuit (PVC) mode with the AAL5SNAP encapsulation type, and the existing Quality of Service (QoS) functionality for ATM PVCs.
  • The Frame Relay DLCI mode, and the existing QoS functionality for Frame Relay.

PVC status signaling works the same way it does in the like-to-like case. The PE router reports the PVC status to the CE router, based on the availability of the pseudowire.

The attachment circuit maximum transmission unit (MTU) on both sides of the pseudowire must match when connected over MPLS. The non-AAL5 traffic (such as OAM cells) is punted to be processed at the RP level. A VC that is configured with OAM cell emulation on the ATM PE router (using the oam-ac emulation-enable command) can send end-to-end F5 loopback cells at configured intervals toward the CE router. When the pseudowire is down, an end-to-end F5 segment alarm indication signal (AIS) and remote defect indication (RDI) is sent from the PE router to the CE router.

The following figure shows the protocol stack for the Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking feature.

Figure 4. Protocol Stack for Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking

Configuring Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking

To configure the Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking feature on an ATM-PE router, perform the following steps:

SUMMARY STEPS

  1. enable
  2. configure terminal
  3. Router(config)# no ip domain lookup
  4. mpls label range minimum-value maximum-value [static minimum-static-value maximum-static-value]
  5. mpls label protocol ldp
  6. mpls ip default-route
  7. mpls ldp graceful-restart
  8. xconnect logging pseudowire status
  9. pseudowire-class [pw-class-name ]
  10. encapsulation mpls
  11. interworking ethernet
  12. exit
  13. interface loopback loopback-interface-number
  14. ip address ip-address mask
  15. exit
  16. interface GigabitEthernet slot/subslot/port
  17. ip address ip-address mask
  18. negotiation auto
  19. mpls ip
  20. exit
  21. interface atm slot/subslot/port
  22. no ip address
  23. atm clock internal
  24. no atm enable-ilmi-trap
  25. exit
  26. interface atm slot/subslot/port [.subinterface-number {point-to-point }]
  27. mtu bytes
  28. no atm enable-ilmi-trap
  29. pvc [name ] vpi/vci l2transport
  30. encapsulation encapsulation-type
  31. xconnect peer-ip-address vc-id encapsulation mpls pw-class pw-class-name
  32. exit

DETAILED STEPS

  Command or Action Purpose

Step 1

enable

Example:


Router> enable

Enables the privileged EXEC mode.

Enter your password, if prompted.

Step 2

configure terminal

Example:


Router# configure terminal

Enters the global configuration mode.

Step 3

Router(config)# no ip domain lookup

Disables the IP domain naming system (DNS).

Step 4

mpls label range minimum-value maximum-value [static minimum-static-value maximum-static-value]

Example:


Router(config)# mpls label range 101 4000 static 4001 5001

Configures the range of local labels available for use with Multiprotocol Label Switching (MPLS) applications on packet interfaces.

Step 5

mpls label protocol ldp

Example:


Router(config)# mpls label protocol ldp

Specifies label distribution protocol (LDP) for the ATM-PE router.

Step 6

mpls ip default-route

Example:


Router(config)# mpls ip default-route

Enables the distribution of labels associated with the IP default route.

Step 7

mpls ldp graceful-restart

Example:


Router(config)# mpls ldp graceful-restart

Enables MPLS LDP graceful restart.

Step 8

xconnect logging pseudowire status

Example:


Router(config)# xconnect logging pseudowire status

Enables system logging (syslog) reporting of pseudowire status events.

Step 9

pseudowire-class [pw-class-name ]

Example:


Router(config)# pseudowire-class  atm-fr-bridged

Establishes a pseudowire class with a name that you specify, and enters the pseudowire class configuration mode.

Step 10

encapsulation mpls

Example:


Router(config-pw-class)# encapsulation mpls

Enables MPLS encapsulation on the interface.

Step 11

interworking ethernet

Example:


Router(config-pw-class)# interworking ethernet

Enables the L2VPN Ethernet interworking feature.

Step 12

exit

Exits pseudowire class configuration mode.

Step 13

interface loopback loopback-interface-number

Example:


Router(config)# interface loopback  0

Specifies the loopback logical interface.

Step 14

ip address ip-address mask

Example:


Router(config-if)# ip address  44.1.1.2 255.255.255.255

Specifies the IP address for the Loopback interface.

Step 15

exit

Exits interface configuration mode.

Step 16

interface GigabitEthernet slot/subslot/port

Example:


Router(config)# interface GigabitEthernet  0/0/1

Specifies the Gigabit Ethernet interface for the connection of the PE routers.

Step 17

ip address ip-address mask

Example:


Router(config-if)# ip address  10.10.1.2 255.255.255.0

Specifies the IP address for the Gigabit Ethernet interface.

Step 18

negotiation auto

Example:


Router(config-if)# negotiation auto

Enables the auto negotiation protocol to configure the speed, duplex, and automatic flow control of the Gigabit Ethernet interface.

Step 19

mpls ip

Example:


Router(config-if)# mpls ip

Enables MPLS forwarding of the IPv4 packets towards the MPLS core.

Step 20

exit

Exits interface configuration mode.

Step 21

interface atm slot/subslot/port

Example:


Router(config)# interface atm 0/1/2

Configures an ATM interface and enters interface configuration mode.

Step 22

no ip address

Example:


Router(config-if)# no ip address

Removes the previously configured IP address.

Step 23

atm clock internal

Example:


Router(config-if)# atm clock internal

Enables the ATM interface to generate the transmit clock internally.

Step 24

no atm enable-ilmi-trap

Example:


Router(config-if)# no atm enable-ilmi-trap

Disables the Integrated Local Management Interface (ILMI) ATM traps.

Step 25

exit

Exits interface configuration mode.

Step 26

interface atm slot/subslot/port [.subinterface-number {point-to-point }]

Example:


Router(config)# interface atm  0/1/2.1 point-to-point

Configures an ATM interface and enters interface configuration mode.

Step 27

mtu bytes

Example:


Router(config-subif)# mtu  1500

Adjusts the maximum packet size or maximum transmission unit (MTU) size.

Note

 
The MTU sizes of both the attachment circuits must match.

Step 28

no atm enable-ilmi-trap

Example:


Router(config-subif)# no atm enable-ilmi-trap

Disables the ILMI ATM traps.

Step 29

pvc [name ] vpi/vci l2transport

Example:


Router(config-subif)# pvc  cisco 10/100 l2transport

Assigns a name to an ATM PVC, specifies the encapsulation type on an ATM PVC, and enters ATM virtual circuit configuration mode.

Step 30

encapsulation encapsulation-type

Example:


Router(config-if-atm-l2trans-pvc)# encapsulation  aal5snap

Sets the AAL5SNAP encapsulation (Any-to-Any) for the ATM point-to-point interface.

Step 31

xconnect peer-ip-address vc-id encapsulation mpls pw-class pw-class-name

Example:


Router(config-if-atm-l2trans-pvc)# xconnect  190.1.1.1 100 encapsulation mpls  pw-class atm-fr-bridged

Binds an attachment circuit to a pseudowire and configures an Any Transport over MPLS (AToM) static pseudowire.

Step 32

exit

Exits global configuration mode.

Example: Frame Relay-to-ATM Bridged Interworking on an ATM-PE Router

The following example shows the configuration of the Frame Relay-to-ATM Bridged Interworking feature on an ATM-PE router: 


no ip domain lookup
mpls label range 101 4000 static 4001 5001
mpls label protocol ldp
mpls ip default-route
mpls ldp graceful-restart
xconnect logging pseudowire status
!
pseudowire-class atm-fr-bridged
encapsulation mpls
interworking ethernet
!
interface Loopback0
ip address 44.1.1.2 255.255.255.255
!
interface GigabitEthernet0/0/1
ip address 10.10.1.2 255.255.255.0
negotiation auto
mpls ip
!
interface ATM0/1/2
no ip address
atm clock INTERNAL
no atm enable-ilmi-trap
!
interface ATM0/1/2.1 point-to-point
mtu 1500
no atm enable-ilmi-trap
pvc 10/100 l2transport
encapsulation aal5snap
xconnect 190.1.1.1 100 pw-class atm-fr-bridged
!
!

Example: Frame Relay-to-ATM Bridged Interworking on a Frame Relay-PE Router

The following example shows the configuration of the Frame Relay-to-ATM Bridged Interworking feature on a Frame Relay-PE router: 


ipv6 unicast-routing
mpls label protocol ldp
mpls ip default-route
mpls ldp graceful-restart
frame-relay switching
xconnect logging pseudowire status
!
controller T1 0/3/0
framing esf
clock source internal
linecode b8zs
cablelength long 0db
channel-group 0 timeslots 1-24
!
pseudowire-class atm-fr-bridged
encapsulation mpls
interworking ethernet
!
interface Loopback0
ip address 190.1.1.1 255.255.255.255
!
interface Serial0/3/0:0
no ip address
encapsulation frame-relay
frame-relay intf-type dce
frame-relay interface-dlci 101 switched
!
interface GigabitEthernet1/3/1
ip address 10.10.1.1 255.255.255.0
negotiation auto
mpls ip
!
connect fr-atm-2 Serial0/3/0:0 101 l2transport
xconnect 44.1.1.2 100 pw-class atm-fr-bridged
!

Gigabit EtherChannel for Virtual Private Wire Service

GEC for AToM is a solution for a VPWS transporting Layer 2 packets over an MPLS backbone with GEC.

This feature enables service providers to supply connectivity between customer sites having data link layer (Layer 2) networks, by using a single, integrated, packet-based network infrastructure—a Cisco MPLS network. Instead of separate networks with separate network management environments, service providers can deliver Layer 2 connections over an MPLS backbone.

Supported Modes

The following modes are supported in the GEC for VPWS feature:

GEC Like-to-Like Mode

The GEC Like-to-Like mode allows switching of data between two physical interfaces in which the two segments (CE1-PE1 and CE2-PE2, as shown in the following figure are both of GEC type.

The GEC Like-to-Like mode has the following features:

Figure 5. Topology of the GEC Like-to-Like Mode for the GEC for VPWS Feature

Any-to-GEC Mode

The Any-to-GEC mode allows switching of data between two physical interfaces in which the two segments, CE1-PE1 and CE2-PE2, are both of different types, while one is GEC, the other can be PPP, Ethernet, Frame Relay, or ATM, as shown in the following figure.

The Any-to-GEC mode has the following features:

Figure 6. Topology of the Any-to-GEC Mode for the GEC for VPWS Feature

Note
Bridged interworking is used when Layer 2 (L2) packets are considered without regard for Layer 3 contents. In bridged interworking, Ethernet frames that are extracted from the attachment circuit are sent over the MPLS pseudowire.

Note
Routed interworking is used to carry Layer 3 packets. In routed interworking, IP packets that are extracted from the attachment circuits are sent over the MPLS pseudowire.

Restrictions for Gigabit EtherChannel for Virtual Private Wire Service

The following are the restrictions for Gigabit EtherChannel for VPWS are the followings:

  • GEC for VPWS does not support Q-in-Q encapsulation and remote port shutdown.
  • A maximum four member links are supported under the port channel and a maximum of 64 port channel bundles are supported per router.

Configuring Gigabit EtherChannel for Virtual Private Wire Service

The GEC VPWS support feature is supported by AToM on the EtherChannel Interface, and includes the following features:

EtherChannel-to-EtherChannel over MPLS (Bridged) Interworking

Configure L2VPN interworking on the upstream interfaces of the PE routers.

After configuring MPLS Forwarding, perform the following steps on the downstream interfaces of the PE routers:

SUMMARY STEPS

  1. enable
  2. configure terminal
  3. mpls label protocol ldp
  4. interface loopback loopback-interface-number
  5. ip address ip-address mask
  6. exit
  7. pseudowire-class pw-class-name
  8. encapsulation mpls
  9. interworking ethernet
  10. exit
  11. interface port-channel number
  12. xconnect peer-ip-address vc-id encapsulation mpls pseudowire-class pw-class-name
  13. interface GigabitEthernet slot | subslot | port
  14. channel-group port-channel number

DETAILED STEPS

  Command or Action Purpose

Step 1

enable

Changes the privilege level for the corresponding CLI session.

Step 2

configure terminal

Example:


Router# configure terminal

Enters global configuration mode.

Step 3

mpls label protocol ldp

Example:


Router# mpls label protocol ldp

Specifies that LDP is the default label distribution protocol.

Step 4

interface loopback loopback-interface-number

Example:


Router# interface loopback 1

Specifies the loopback interface, and enters interface configuration mode.

Step 5

ip address ip-address mask

Example:


Router# ip address 10.10.2.1 255.255.255.0

Sets the IP address and mask for the loopback interface.

Step 6

exit

Exits interface configuration mode.

Step 7

pseudowire-class pw-class-name

Example:


Router(config)# pseudowire-class gec-bridged

Specifies the name of a Layer 2 pseudowire class and enters the pseudowire class configuration mode.

Step 8

encapsulation mpls

Example:


Router(config-pw)# encapsulation mpls

Uses MPLS as the tunneling method to encapsulate data in the pseudowire.

Step 9

interworking ethernet

Example:


Router(config-pw)# interworking ethernet

Enables the L2VPN Interworking feature, and causes Ethernet frames to be extracted from the attachment circuit and sent over the pseudowire. Ethernet end-to-end transmission is assumed. Attachment circuit frames that do not contain Ethernet frames are dropped. In the case of VLAN, the VLAN tag is removed, which leaves a pure Ethernet frame.

Step 10

exit

Exits xconnect configuration mode.

Step 11

interface port-channel number

Example:


Router(config)# interface port-channel 1

Creates an EtherChannel interface on the Cisco Cable Modem Termination System (CMTS).

Step 12

xconnect peer-ip-address vc-id encapsulation mpls pseudowire-class pw-class-name

Example:


Router(config-if)# xconnect 10.0.0.1 707 encapsulation mpl pseudowire-class gec-bridged

Binds an attachment circuit to a pseudowire to configure an AToM static pseudowire, specifies MPLS as the tunneling method, and enters the xconnect configuration mode.

Step 13

interface GigabitEthernet slot | subslot | port

Example:


Router(config)# interface GigabitEthernet 0/0/1

Specifies the Gigabit Ethernet interface, and enters interface configuration mode.

Step 14

channel-group port-channel number

Example:


Router(config-if) channel-group 1

Configures an EtherChannel interface to an EtherChannel group.

What to do next


Note
The EtherChannel-to-EtherChannel over MPLS (Bridged) Interworking mode is also supported under VLAN.

EtherChannel-to-EtherChannel over MPLS (Routed) Interworking

Configure L2VPN interworking on the upstream interfaces of the PE routers.

After configuring MPLS Forwarding, perform the following steps on the downstream interfaces of the PE routers:

SUMMARY STEPS

  1. enable
  2. configure terminal
  3. mpls label protocol ldp
  4. interface loopback loopback-interface-number
  5. ip address ip-address mask
  6. exit
  7. pseudowire-class pw-class-name
  8. encapsulation mpls
  9. interworking ip
  10. exit
  11. interface port-channel number
  12. xconnect peer-ip-address vc-id encapsulation mpls pseudowire-class pw-class-name
  13. interface GigabitEthernet slot | subslot | port
  14. channel-group port-channel number

DETAILED STEPS

  Command or Action Purpose

Step 1

enable

Changes the privilege level for the corresponding CLI session.

Step 2

configure terminal

Example:


Router# configure terminal

Enters global configuration mode.

Step 3

mpls label protocol ldp

Example:


Router# mpls label protocol ldp

Specifies that LDP is the default label distribution protocol.

Step 4

interface loopback loopback-interface-number

Example:


Router# interface loopback 1

Specifies the loopback interface, and enters interface configuration mode.

Step 5

ip address ip-address mask

Example:


Router# ip address 10.10.2.1 255.255.255.0

Sets the IP address and mask for the loopback interface.

Step 6

exit

Exits interface configuration mode.

Step 7

pseudowire-class pw-class-name

Example:


Router(config)# pseudowire-class gec-bridged

Specifies the name of a Layer 2 pseudowire class and enters pseudowire class configuration mode.

Step 8

encapsulation mpls

Example:


Router(config-pw)# encapsulation mpls

Uses MPLS as the tunneling method to encapsulate data in the pseudowire.

Step 9

interworking ip

Example:


Router(config-pw)# interworking ip

Enables the L2VPN Interworking feature, and causes IP packets to be extracted from the attachment circuit and sent over the pseudowire. Attachment circuit frames that do not contain IPv4 packets are dropped.

Step 10

exit

Exits xconnect configuration mode.

Step 11

interface port-channel number

Example:


Router(config)# interface port-channel 1

Creates an EtherChannel interface on the Cisco Cable Modem Termination System (CMTS).

Step 12

xconnect peer-ip-address vc-id encapsulation mpls pseudowire-class pw-class-name

Example:


Router(config-if)# xconnect 10.0.0.1 707 encapsulation mpl pseudowire-class gec-routed

Binds an attachment circuit to a pseudowire to configure an AToM static pseudowire, specifies MPLS as the tunneling method, and enters xconnect configuration mode.

Step 13

interface GigabitEthernet slot | subslot | port

Example:


Router(config)# interface GigabitEthernet 0/0/1

Specifies the Gigabit Ethernet interface, and enters interface configuration mode.

Step 14

channel-group port-channel number

Example:


Router(config-if) channel-group 1

Configures EtherChannel interfaces to an EtherChannel group.

What to do next


Note
The EtherChannel-to-EtherChannel over MPLS (Routed) Interworking mode is also supported under VLAN.

Example: GEC Like-to-Like (Routed) Interworking

The following example shows the configuration of the GEC Like-to-Like (Routed) Interworking feature: 


no ip domain lookup
mpls label range 101 4000 static 4001 5001
mpls label protocol ldp
mpls ip default-route
mpls ldp graceful-restart
xconnect logging pseudowire status
!
pseudowire-class gec-bridged
encapsulation mpls
interworking ethernet!
pseudowire-class gec-routed
encapsulation mpls
interworking ip
!
interface Loopback0
ip address 44.1.1.2 255.255.255.255
!
interface GigabitEthernet0/0/1
ip address 10.10.1.2 255.255.255.0
negotiation auto
mpls ip
!
interface port-channel 1
xconnect 190.1.1.1 100 encapsulation mpls pw-class gec-bridged
!
interface GigabitEthernet0/0/3
channel-group 1
!
interface GigabitEthernet0/0/2
channel-group 1
!
router ospf 10
log-adjacency-changes
network 44.1.1.2 0.0.0.0 area 0
network 10.10.1.2 0.0.0.255 area 0

Any-to-EtherChannel over MPLS (Bridged) Interworking

You can configure Any-to-EtherChannel over MPLS (Bridged) interworking on the Cisco ASR 1000 Series Routers.

Any-to-EtherChannel over MPLS (Bridged) interworking supports the following modes:

  • Frame Relay-to-EtherChannel
  • ATM-to-EtherChannel
  • Ethernet-to-EtherChannel

Irrespective of the mode used, in Any-to-EtherChannel over MPLS (Bridged) interworking, configure L2VPN interworking on the upstream interfaces of PE routers.

Perform the following steps on the downstream interfaces of the PE routers:

SUMMARY STEPS

  1. enable
  2. configure terminal
  3. mpls label protocol ldp
  4. interface loopback loopback-interface-number
  5. ip address ip-address mask
  6. exit
  7. pseudowire-class pw-class-name
  8. encapsulation mpls
  9. interworking ethernet
  10. interface GigabitEthernet slot | subslot | port
  11. xconnect peer-ip-address vc-id encapsulation mpls pseudowire-class pw-class-name

DETAILED STEPS

  Command or Action Purpose

Step 1

enable

Changes the privilege level for the corresponding CLI session.

Step 2

configure terminal

Example:


Router# configure terminal

Enters global configuration mode.

Step 3

mpls label protocol ldp

Example:


Router# mpls label protocol ldp

Specifies that LDP is the default label distribution protocol.

Step 4

interface loopback loopback-interface-number

Example:


Router# interface loopback 1

Specifies the loopback interface, and enters the interface configuration mode.

Step 5

ip address ip-address mask

Example:


Router# ip address 10.10.2.1 255.255.255.0

Sets the IP address and mask for the loopback interface.

Step 6

exit

Exits interface configuration mode.

Step 7

pseudowire-class pw-class-name

Example:


Router(config)# pseudowire-class gec-bridged

Specifies the name of a Layer 2 pseudowire class and enters the pseudowire class configuration mode.

Step 8

encapsulation mpls

Example:


Router(config-pw)# encapsulation mpls

Uses MPLS as the tunneling method to encapsulate data in the pseudowire.

Step 9

interworking ethernet

Example:


Router(config-pw)# interworking ethernet

Enables the L2VPN Interworking feature, and causes Ethernet frames to be extracted from the attachment circuit and sent over the pseudowire. Ethernet end-to-end transmission is assumed. Attachment circuit frames that do not contain Ethernet frames are dropped. In the case of VLAN, the VLAN tag is removed, which leaves a pure Ethernet frame.

Step 10

interface GigabitEthernet slot | subslot | port

Example:


Router(config)# interface GigabitEthernet 0/0/1

Specifies the Gigabit Ethernet interface, and enters interface configuration mode.

Step 11

xconnect peer-ip-address vc-id encapsulation mpls pseudowire-class pw-class-name

Example:


Router(config-if)# xconnect 10.0.0.1 707 encapsulation mpl pseudowire-class gec-bridged

Binds an attachment circuit to a pseudowire to configure an AToM static pseudowire, specifies MPLS as the tunneling method, and enters the xconnect configuration mode.

What to do next


Note
Ethernet-to-EtherChannel over MPLS (Bridge) Interworking mode is also supported under VLAN.

Any-to-EtherChannel over MPLS (Routed) Interworking

You can configure Any-to-EtherChannel over MPLS (Routed) interworking on the Cisco ASR 1000 Series Routers.

Any-to-EtherChannel over MPLS (Routed) interworking supports the following modes:

  • ATM-to-EtherChannel
  • Ethernet-to-EtherChannel
  • PPP-to-EtherChannel

Configure L2VPN interworking on the upstream interfaces of PE routers.

Perform the following steps on the downstream interfaces of the PE routers:

SUMMARY STEPS

  1. enable
  2. configure terminal
  3. ipv6 unicast-routing
  4. mpls ip default-route
  5. mpls ldp graceful-restart
  6. xconnect logging pseudowire status
  7. controller t1 slot/subslot/port
  8. clock source internal
  9. linecode b8zs
  10. cablelength long db-loss-value
  11. channel-group channel-group-number timeslots range
  12. exit
  13. pseudowire-class [pw-class-name ]
  14. encapsulation mpls
  15. interworking ethernet
  16. exit
  17. interface loopback loopback-interface-number
  18. ip address ip-address mask
  19. exit
  20. interface serial slot/subslot/port:timeslot
  21. no ip address
  22. encapsulation ppp
  23. clock source internal
  24. xconnect peer-loopback vc-id pw-class pe-class-name

DETAILED STEPS

  Command or Action Purpose

Step 1

enable

Example:

Router> enable

Enables privileged EXEC mode.

Enter your password, if prompted.

Step 2

configure terminal

Example:


Router# configure terminal

Enters global configuration mode.

Step 3

ipv6 unicast-routing

Example:


Router# ipv6 unicast-routing

(Optional) Enables the task of forwarding the IPv6 unicast datagrams.

Step 4

mpls ip default-route

Example:


Router(config)# mpls ip default-route

Enables the distribution of labels associated with the IP default route.

Step 5

mpls ldp graceful-restart

Example:


Router(config)# mpls ldp graceful-restart

Enables MPLS LDP graceful restart.

Step 6

xconnect logging pseudowire status

Example:


Router(config)# xconnect logging pseudowire status

Enables system logging (syslog) reporting of pseudowire status events.

Step 7

controller t1 slot/subslot/port

Example:


Router(config)# controller T1 0/3/0

Configures a T1 controller and enters controller configuration mode.

Step 8

clock source internal

Example:


Router(config-controller)# clock source internal

Configures the clock source of a DS1 link and uses the internal clock from the interface.

Step 9

linecode b8zs

Example:


Router(config-controller)# linecode b8zs

Specifies Binary 8-Zero Substitution (B8ZS) as the line code type for the T1 controller.

Step 10

cablelength long db-loss-value

Example:


Router(config-controller)# cablelength long 0db

Decreases the transmit signal by 0 dB. This is the default value.

Step 11

channel-group channel-group-number timeslots range

Example:


Router(config-controller)# channel-group 0 timeslots 1-24

Configures serial WAN on a T1 or E1 interface.

Step 12

exit

Exits pseudowire class configuration mode.

Step 13

pseudowire-class [pw-class-name ]

Example:


Router(config)# pseudowire-class  atm-fr-bridged

Establishes a pseudowire class with a name that you specify and enters the pseudowire class configuration mode.

Step 14

encapsulation mpls

Example:


Router(config-pw-class)# encapsulation mpls

Enables MPLS encapsulation on the interface.

Step 15

interworking ethernet

Example:


Router(config-pw-class)# interworking ethernet

Enables the L2VPN Ethernet interworking feature.

Step 16

exit

Exits pseudowire class configuration mode.

Step 17

interface loopback loopback-interface-number

Example:


Router(config)# interface loopback  0

Specifies the Loopback logical interface.

Step 18

ip address ip-address mask

Example:


Router(config-if)# ip address  44.1.1.2 255.255.255.255

Specifies the IP address for the Loopback interface.

Step 19

exit

Exits the interface configuration mode.

Step 20

interface serial slot/subslot/port:timeslot

Example:


Router(config)# interface Serial 0/3/0:0

Specifies a serial interface created on a channelized T1 controller.

Step 21

no ip address

Example:


Router(config-if)# no ip address

Removes the previously configured IP address.

Step 22

encapsulation ppp

Example:


Router(config-if)# encapsulation frame-relay

Configures the PPP (for serial interface) encapsulation on serial interface.

Step 23

clock source internal

Specifies that the T1/E1 link uses the internal clock from the interface.

Step 24

xconnect peer-loopback vc-id pw-class pe-class-name

Binds an attachment circuit to a pseudowire to configure an AToM static pseudowire, specifies MPLS as the tunneling method, and enters xconnect configuration mode.

What to do next


Note
Ethernet-to-EtherChannel over MPLS (Bridge) Interworking mode is also supported under VLAN.

High-Level Data Link Control-Ethernet Interworking

HDLC-Ethernet over MPLS is part of Any Transport over MPLS (AToM) solution. High-Level Link Control (HDLC) and Ethernet are two link-layer transports that utilize the AToM architecture. This section describes how these two transport types can communicate with each other using the AToM framework.

The following figure shows the topology of the HDLC-Ethernet Interworking feature.

Figure 7. Topology of the HDLC-Ethernet Interworking Feature

The following features are supported from Cisco IOS XE Release 3.13.0S on the Cisco ASR 1000 Series Aggregation Services Routers:

  • HDLC-Ethernet Bridged-Mode Interworking
  • HDLC-Ethernet Routed-Mode Interworking
  • HDLC Encapsulation: CISCO
  • Ethernet Encapsulation: Dot1Q, QinQ, Port Interface

Prerequisites for HDLC-Ethernet Interworking

Perform the following tasks to enable HDLC-Ethernet interworking:

  • Configure a controller slot on Ethernet CE: 

controller E1 2/0 
channel-group 0 timeslots 1 
no shutdown 
interface Serial2/0:0 
no shutdown
  • Configure an Ethernet CE interface for Ethernet interworking: 

bridge irb
bridge 1 protocol ieee
bridge 1 route ip
interface Serial2/0:0
no bridge-group 1
no ip address
!
int BVI1
no ip address
ip address 192.168.1.1 255.255.255.0
no shut
!
interface Serial2/0:0
description Connect to PE1
no ip address
encapsulation hdlc
bridge-group 1
no shut
  • Configure an Ethernet CE interface for IP interworking: 

interface Serial2/0:0
description Connect to PE1
ip address 192.168.1.1 255.255.255.0
encapsulation hdlc
no shut

Restrictions for HDLC-Ethernet Interworking

The following features are not supported:

  • HDLC encapsulation: none CISCO
  • IPv6 is not supported in routed mode

Configuring HDLC-Ethernet Interworking

HDLC-Ethernet Interworking can be configured in the following two modes:

Bridge Mode

Perform the following steps to configure the HDLC-Ethernet Interworking in the bridge mode via interface-based configuration:

On the HDLC-PE

SUMMARY STEPS

  1. enable
  2. configure terminal
  3. pseudowire-class pw-class-name
  4. encapsulation mpls
  5. interworking ethernet
  6. interface serial slot | subslot | port
  7. no ip address
  8. xconnect peer-ip-address vc-id pseudowire-class pw-class-name

DETAILED STEPS

  Command or Action Purpose

Step 1

enable

Changes the privilege level for the corresponding CLI session.

Step 2

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3

pseudowire-class pw-class-name

Example:

Router(config)# pseudowire-class pw-iw-ether

Specifies the name of a Layer 2 pseudowire class and enters pseudowire class configuration mode.

Step 4

encapsulation mpls

Example:

Router(config-pw)# encapsulation mpls

Uses MPLS as the tunneling method to encapsulate data in the pseudowire.

Step 5

interworking ethernet

Example:

Router(config-pw)# interworking ethernet

Enables the L2VPN Interworking feature, and causes Ethernet frames to be extracted from the attachment circuit and sent over the pseudowire. Ethernet end-to-end transmission is assumed. Attachment circuit frames that do not contain Ethernet frames are dropped. In the case of VLAN, the VLAN tag is removed, which leaves a pure Ethernet frame.

Step 6

interface serial slot | subslot | port

Example:

Router(config)# interface Serial0/1/0:0

Specifies the serial interface, and enters interface configuration mode.

Step 7

no ip address

Example:

Router(config-if)# no ip address

Removes all the IP addresses of the interface.

Step 8

xconnect peer-ip-address vc-id pseudowire-class pw-class-name

Example:

Router(config-if)# xconnect 17.17.17.17 100 pw-class pw-iw-ether

Binds an attachment circuit to a pseudowire to configure an AToM static pseudowire, specifies MPLS as the tunneling method, and enters xconnect configuration mode.

On the Ethernet PE

SUMMARY STEPS

  1. enable
  2. configure terminal
  3. pseudowire-class pw-class-name
  4. encapsulation mpls
  5. interworking ethernet
  6. interface GigabitEthernet slot | subslot | port
  7. encapsulation dot1Q vlan-id
  8. xconnect peer-ip-address vc-id pseudowire-class pw-class-name

DETAILED STEPS

  Command or Action Purpose

Step 1

enable

Changes the privilege level for the corresponding CLI session.

Step 2

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3

pseudowire-class pw-class-name

Example:

Router(config)# pseudowire-class pw-iw-ether

Specifies the name of a Layer 2 pseudowire class and enters pseudowire class configuration mode.

Step 4

encapsulation mpls

Example:

Router(config-pw)# encapsulation mpls

Uses MPLS as the tunneling method to encapsulate data in the pseudowire.

Step 5

interworking ethernet

Example:

Router(config-pw)# interworking ethernet

Enables the L2VPN Interworking feature, and causes Ethernet frames to be extracted from the attachment circuit and sent over the pseudowire. Ethernet end-to-end transmission is assumed. Attachment circuit frames that do not contain Ethernet frames are dropped. In the case of VLAN, the VLAN tag is removed, which leaves a pure Ethernet frame.

Step 6

interface GigabitEthernet slot | subslot | port

Example:

Router(config)# interface GigabitEthernet0/0/0.3

Specifies the Gigabit Ethernet interface, and enters interface configuration mode.

Step 7

encapsulation dot1Q vlan-id

Example:

Router(config-if)# encapsulation dot1Q 3

Removes all the IP addresses of the interface.

Step 8

xconnect peer-ip-address vc-id pseudowire-class pw-class-name

Example:

Router(config-if)# xconnect 16.16.16.16 100 pseudowire-class pw-iw-ether

Binds an attachment circuit to a pseudowire to configure an AToM static pseudowire, specifies MPLS as the tunneling method, and enters xconnect configuration mode.

What to do next

Perform the following steps to configure the HDLC-Ethernet Interworking in the bridge mode via protocol-based configuration:

On the HDLC-PE

SUMMARY STEPS

  1. enable
  2. configure terminal
  3. l2vpn xconnect context xc-name
  4. interworking ethernet
  5. member interface-id
  6. member ip-address vc-id encapsulation mpls

DETAILED STEPS

  Command or Action Purpose

Step 1

enable

Changes the privilege level for the corresponding CLI session.

Step 2

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3

l2vpn xconnect context xc-name

Example:

Router(config)# l2vpn xconnect context HDLC

Creates an empty cross-connect, and enters xconnect submode.

Step 4

interworking ethernet

Example:

Router(config)# interworking ethernet

Enables the L2VPN Interworking feature, and causes Ethernet frames to be extracted from the attachment circuit and sent over the pseudowire. Ethernet end-to-end transmission is assumed. Attachment circuit frames that do not contain Ethernet frames are dropped. In the case of VLAN, the VLAN tag is removed, which leaves a pure Ethernet frame.

Step 5

member interface-id

Example:

Router(config)# member serial0/1/0:0

Adds an interface as an AC segment of xconnect.

Step 6

member ip-address vc-id encapsulation mpls

Example:

Router(config)# member 17.17.17.17 100 encapsulation mpls

Adds a pseudowire member to xconnect.

On the Ethernet PE

SUMMARY STEPS

  1. enable
  2. configure terminal
  3. l2vpn xconnect context foo
  4. interworking ethernet
  5. member interface-id
  6. member ip-address vc-id encapsulation mpls

DETAILED STEPS

  Command or Action Purpose

Step 1

enable

Changes the privilege level for the corresponding CLI session.

Step 2

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3

l2vpn xconnect context foo

Example:

Router(config)# l2vpn xconnect context foo

Creates an empty cross-connect, and enters xconnect submode.

Step 4

interworking ethernet

Example:

Router(config)# interworking ethernet

Enables the L2VPN Interworking feature, and causes Ethernet frames to be extracted from the attachment circuit and sent over the pseudowire. Ethernet end-to-end transmission is assumed. Attachment circuit frames that do not contain Ethernet frames are dropped. In the case of VLAN, the VLAN tag is removed, which leaves a pure Ethernet frame.

Step 5

member interface-id

Example:

Router(config)# member GigabitEthernet0/0/0.3

Adds an interface as an AC segment of xconnect.

Step 6

member ip-address vc-id encapsulation mpls

Example:

Router(config)# member 16.16.16.16 100 encapsulation mpls

Adds a pseudowire member to xconnect.

Routed Mode

Perform the following steps to configure the HDLC-Ethernet Interworking in the routed mode via interface-based configuration:

On HDLC-PE

SUMMARY STEPS

  1. enable
  2. configure terminal
  3. pseudowire-class pw-class-name
  4. encapsulation mpls
  5. interworking ip
  6. interface serial slot | subslot | port
  7. no ip address
  8. xconnect peer-ip-address vc-id pseudowire-class pw-class-name

DETAILED STEPS

  Command or Action Purpose

Step 1

enable

Changes the privilege level for the corresponding CLI session.

Step 2

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3

pseudowire-class pw-class-name

Example:

Router(config)# pseudowire-class pw-ip-ether

Specifies the name of a Layer 2 pseudowire class and enters pseudowire class configuration mode.

Step 4

encapsulation mpls

Example:

Router(config-pw)# encapsulation mpls

Uses MPLS as the tunneling method to encapsulate data in the pseudowire.

Step 5

interworking ip

Example:

Router(config-pw)# interworking ip

Enables the L2VPN Interworking feature, and causes IP packets to be extracted from the attachment circuit and sent over the pseudowire. Attachment circuit frames that do not contain IPv4 packets are dropped.

Step 6

interface serial slot | subslot | port

Example:

Router(config)# interface Serial0/1/0:0

Specifies the serial interface, and enters interface configuration mode.

Step 7

no ip address

Example:

Router(config-if)# no ip address

Removes all the IP addresses of the interface.

Step 8

xconnect peer-ip-address vc-id pseudowire-class pw-class-name

Example:

Router(config-if)# xconnect 17.17.17.17 100 pw-class pw-ip-ether

Binds an attachment circuit to a pseudowire to configure an AToM static pseudowire, specifies MPLS as the tunneling method, and enters xconnect configuration mode.

On Ethernet PE

SUMMARY STEPS

  1. enable
  2. configure terminal
  3. pseudowire-class pw-class-name
  4. encapsulation mpls
  5. interworking ip
  6. interface GigabitEthernet slot | subslot | port
  7. encapsulation dot1Q vlan-id
  8. xconnect peer-ip-address vc-id pseudowire-class pw-class-name

DETAILED STEPS

  Command or Action Purpose

Step 1

enable

Changes the privilege level for the corresponding CLI session.

Step 2

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3

pseudowire-class pw-class-name

Example:

Router(config)# pseudowire-class pw-ip-ether

Specifies the name of a Layer 2 pseudowire class and enters pseudowire class configuration mode.

Step 4

encapsulation mpls

Example:

Router(config-pw)# encapsulation mpls

Uses MPLS as the tunneling method to encapsulate data in the pseudowire.

Step 5

interworking ip

Example:

Router(config-pw)# interworking ip

Enables the L2VPN Interworking feature, and causes IP packets to be extracted from the attachment circuit and sent over the pseudowire. Attachment circuit frames that do not contain IPv4 packets are dropped.

Step 6

interface GigabitEthernet slot | subslot | port

Example:

Router(config)# interface GigabitEthernet0/0/0.3

Specifies the Gigabit Ethernet interface, and enters interface configuration mode.

Step 7

encapsulation dot1Q vlan-id

Example:

Router(config-if)# encapsulation dot1Q 3

Enables IEEE 802.1Q encapsulation of traffic on a specified subinterface in a VLAN.

Step 8

xconnect peer-ip-address vc-id pseudowire-class pw-class-name

Example:

Router(config-if)# xconnect 16.16.16.16 100 pseudowire-class pw-ip-ether

Binds an attachment circuit to a pseudowire to configure an AToM static pseudowire, specifies MPLS as the tunneling method, and enters xconnect configuration mode.

What to do next

Perform the following steps to configure the HDLC-Ethernet Interworking in the routed mode via protocol-based configuration:

On HDLC-PE

SUMMARY STEPS

  1. enable
  2. configure terminal
  3. l2vpn xconnect context foo
  4. interworking ip
  5. member interface-id
  6. member ip-address encapsulation mpls

DETAILED STEPS

  Command or Action Purpose

Step 1

enable

Changes the privilege level for the corresponding CLI session.

Step 2

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3

l2vpn xconnect context foo

Example:

Router(config)# l2vpn xconnect context foo

Creates an empty cross-connect, and enters xconnect submode.

Step 4

interworking ip

Example:

Router(config)# interworking ip

Enables the L2VPN Interworking feature, and causes IP packets to be extracted from the attachment circuit and sent over the pseudowire. Attachment circuit frames that do not contain IPv4 packets are dropped.

Step 5

member interface-id

Example:

Router(config)# member serial0/1/0:0

Adds an interface as an AC segment of xconnect.

Step 6

member ip-address encapsulation mpls

Example:

Router(config)# member 17.17.17.17 100 encapsulation mpls

Adds a pseudowire member to xconnect.

On Ethernet PE

SUMMARY STEPS

  1. enable
  2. configure terminal
  3. l2vpn xconnect context foo
  4. interworking ip
  5. member interface-id
  6. member ip-address vcid encapsulation mpls

DETAILED STEPS

  Command or Action Purpose

Step 1

enable

Changes the privilege level for the corresponding CLI session.

Step 2

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3

l2vpn xconnect context foo

Example:

Router(config)# l2vpn xconnect context foo

Creates an empty cross-connect, and enters xconnect submode.

Step 4

interworking ip

Example:

Router(config)# interworking ip

Enables the L2VPN Interworking feature, and causes IP packets to be extracted from the attachment circuit and sent over the pseudowire. Attachment circuit frames that do not contain IPv4 packets are dropped.

Step 5

member interface-id

Example:

Router(config)# member GigabitEthernet0/0/0.3

Adds an interface as an AC segment of xconnect.

Step 6

member ip-address vcid encapsulation mpls

Example:

Router(config)# member 16.16.16.16 100 encapsulation mpls

Adds a pseudowire member to xconnect.

Example: HDLC-Ethernet Interworking Configuration

The following examples show how to configure the HDLC-Ethernet Interworking feature, and verify the configuration using show commands for legacy and new protocol-based outputs on the Cisco ASR 1000 Series Aggregation Services Routers:

Example: Different Forms of Protocol-Based CLI Configuration

The following example shows how to configure the HDLC-Ethernet interworking on the Controller slot on Ethernet CE: 


controller E1 2/0 
channel-group 0 timeslots 1 
no shutdown 
interface Serial2/0:0 
no shutdown

The following example shows how to configure the HDLC-Ethernet interworking on the Controller slot on Ethernet PE: 


controller E1 0/1/0 
channel-group 0 timeslots 1 
no shutdown 
interface Serial0/1/0:0
no shutdown

The following example shows how to configure the HDLC-Ethernet interworking using legacy CLI.

The following example shows how to configure on HDLC-CE and HDLC-PE in Bridged (Ethernet) mode using legacy CLI:

On HDLC-CE 


configure terminal
bridge irb
bridge 1 protocol ieee
bridge 1 route ip
!
int BVI1 
ip address 192.168.1.1 255.255.255.0
no shut
!
interface Serial2/0:0
description Connect to PE1
encapsulation hdlc
bridge-group 1
no shut
end

HDLC-PE: 


configure terminal
pseudowire-class pw-iw-eth
 encapsulation mpls
 interworking Ethernet
!
interface Serial0/1/0:0
 description Connect to CE1
 encapsulation hdlc
 no ip address
 xconnect 192.0.2.3 100 pw-class pw-iw-eth
 no shut
end

The following example shows how to configure Ethernet on Ethernet-CE and Ethernet-PE in Bridged (Ethernet) mode using legacy CLI:

On Ethernet-CE 


configure terminal
interface GigabitEthernet0/1
description Connect to PE2
ip address 192.168.1.2 255.255.255.0
ip irdp
ip irdp maxadvertinterval 4
no shut
end

On Ethernet-PE 


configure terminal
pseudowire-class pw-iw-eth
 encapsulation mpls
 interworking Ethernet
!
interface GigabitEthernet1/0/0
 description Connect to CE2
 no ip address
xconnect 192.0.2.1 100 pw-class pw-iw-eth
 no shut
end

The following example shows how to configure VLAN at Ethernet-CE and Ethernet-PE in Bridged (Ethernet) mode using legacy CLI:

On Ethernet-CE: 


configure terminal
interface GigabitEthernet0/1
no ip address
no shut
!
interface GigabitEthernet0/1.10
description Connect to PE2
encapsulation dot1q 10
ip address 192.168.1.2 255.255.255.0
ip irdp
ip irdp maxadvertinterval 4
no shut
end

On Ethernet-PE: 


configure terminal
pseudowire-class pw-iw-eth
 encapsulation mpls
 interworking Ethernet
!
interface GigabitEthernet1/0/0
no ip address
no shut
!
interface GigabitEthernet1/0/0.10
 description Connect to CE2
 encapsulation dot1Q 10
 no ip address
 xconnect 192.0.2.1 100 pw-class pw-iw-eth
 no shut
end

The following example shows how to configureQinQ at Ethernet-CE and Ethernet-PE in Bridged (Ethernet) mode using legacy CLI:

On Ethernet-CE: 


configure terminal
interface GigabitEthernet0/1
no ip address
no shut
!
interface GigabitEthernet0/1.10
 description Connect to PE2
encapsulation dot1q 10 second-dot1q 20 
ip address 192.168.1.2 255.255.255.0
ip irdp
ip irdp maxadvertinterval 4
no shut
end

On Ethernet-PE: 


configure terminal
pseudowire-class pw-iw-eth
 encapsulation mpls
 interworking Ethernet
!
interface GigabitEthernet1/0/0
no ip address
no shut
!
interface GigabitEthernet1/0/0.10
 description Connect to CE2
 encapsulation dot1Q 10 second-dot1q 20
 no ip address
 xconnect 192.0.2.1 100 pw-class pw-iw-eth
 no shut
end

The following example shows how to configure HDLC-Ethernet interworking using Protocol-Based CLI:

The following example shows how to configure HDLC on HDLC-CE and HDLC-PE in Bridged (Ethernet) mode using protocol-based CLI:

On HDLC-CE: 


configure terminal
bridge irb
bridge 1 protocol ieee
bridge 1 route ip
!
int BVI1 
ip address 192.168.1.1 255.255.255.0
no shut
!
interface Serial2/0:0
description Connect to PE1
encapsulation hdlc
bridge-group 1
no shut
end

On HDLC-PE: 


configure terminal
interface Serial0/1/0:0
description Connect to CE1
encapsulation hdlc
no ip addres
no shut
!
Interface pseudowire101
encapsulation mpls
neighbor 192.0.2.3 100
signaling protocol ldp 
no shut
l2vpn xconnect context foohdlc
interworking ethernet
member Serial0/1/0:0
member pseudowire101
no shut
end

The following example shows how to configure Ethernet on Ethernet-CE and Ethernet-PE - Bridged (Ethernet) mode using protocol-based CLI:

On Ethernet-CE: 


configure terminal
interface GigabitEthernet0/1
description Connect to PE2
ip address 192.168.1.2 255.255.255.0
ip irdp
ip irdp maxadvertinterval 4
no shut
end

On Ethernet-PE: 


configure terminal
interface GigabitEthernet1/0/0
 description Connect to CE2
no ip address
no shut
!
Interface pseudowire101
encapsulation mpls
neighbor 192.0.2.1 100
signaling protocol ldp 
no shut
!
l2vpn xconnect context fooeth
interworking ethernet
member GigabitEthernet1/0/0
member pseudowire101
no shut
end

The following example shows how to configure VLAN on Ether-CE and Ethernet-PE in Bridged (Ethernet) mode using protocol-based CLI:

On Ethernet-CE: 


configure terminal
!
interface GigabitEthernet0/1
no ip address
no shut
!
interface GigabitEthernet0/1.10
encapsulation dot1q 10
description Connect to PE2
ip address 192.168.1.2 255.255.255.0
ip irdp
ip irdp maxadvertinterval 4
no shut
end

On Ethernet-PE: 


configure terminal
!
interface GigabitEthernet1/0/0
no ip address
no shut
!
interface GigabitEthernet1/0/0.10
description Connect to CE2
encapsulation dot1q 10
no ip addres
no shut
!
Interface pseudowire101
encapsulation mpls
neighbor 192.0.2.1 100
signaling protocol ldp 
no shut
!
l2vpn xconnect context foovlan
interworking ethernet
member GigabitEthernet1/0/0.10
member pseudowire101
no shut
end

The following example shows how to configure QinQ on Ethernet-CE and Ethernet-PE in Bridged (Ethernet) mode using protocol-based CLI:

Ethernet-CE: 


configure terminal
!
interface GigabitEthernet0/1
no ip address
no shut
!
interface GigabitEthernet0/1.10
description Connect to PE2
encapsulation dot1q 10 second-dot1q 20 
ip address 192.168.1.2 255.255.255.0
ip irdp
ip irdp maxadvertinterval 4
no shut
end

Ethernet-PE: 


configure terminal
!
interface GigabitEthernet1/0/0
no ip address
no shut
!
interface GigabitEthernet1/0/0.10
description Connect to CE2
encapsulation dot1q 10 second-dot1q 20 
no ip addres
no shut
!
Interface pseudowire101
encapsulation mpls
neighbor 192.0.2.1 100
signaling protocol ldp 
no shut
!
l2vpn xconnect context fooqinq
interworking ethernet
member GigabitEthernet1/0/0.10
member pseudowire101
no shut
end

Example: Verifying the Configuration for HDLC-Ethernet Interworking

Use the following show commands to verify the configuration for HDLC-Ethernet interworking:

Port mode

The following example shows how to verify the HDLC configuration on PE: 


Router# show mpls l2transport vc
Local intf     Local circuit              Dest address    VC ID      Status
-------------  -------------------------- --------------- ---------- ----------
Se0/1/0:0      HDLC                       104.0.0.1       101        UP 
Router# show mpls l2transport vc detail
Local interface: Se0/1/0:0 up, line protocol up, HDLC up
  Interworking type is Ethernet
  Destination address: 104.0.0.1, VC ID: 101, VC status: up
    Output interface: Fa0/0/1, imposed label stack {20 22}
    Preferred path: not configured  
    Default path: active
    Next hop: 10.1.1.2
  Create time: 00:00:19, last status change time: 00:00:15
    Last label FSM state change time: 00:00:15
  Signaling protocol: LDP, peer 104.0.0.1:0 up
    Targeted Hello: 102.0.0.1(LDP Id) -> 104.0.0.1, LDP is UP
    Graceful restart: configured and enabled
    Non stop routing: not configured and not enabled
    Status TLV support (local/remote)   : enabled/supported
      LDP route watch                   : enabled
      Label/status state machine        : established, LruRru
      Last local dataplane   status rcvd: No fault
      Last BFD dataplane     status rcvd: Not sent
      Last BFD peer monitor  status rcvd: No fault
      Last local AC  circuit status rcvd: No fault
      Last local AC  circuit status sent: No fault
      Last local PW i/f circ status rcvd: No fault
      Last local LDP TLV     status sent: No fault
      Last remote LDP TLV    status rcvd: No fault
      Last remote LDP ADJ    status rcvd: No fault
    MPLS VC labels: local 33, remote 22 
    Group ID: local 0, remote 0
    MTU: local 1500, remote 1500
    Remote interface description: Connect to CE2
  Sequencing: receive disabled, send disabled
  Control Word: On
  SSO Descriptor: 104.0.0.1/101, local label: 33
  Dataplane:
    SSM segment/switch IDs: 4274/4273 (used), PWID: 26
  VC statistics:
    transit packet totals: receive 3, send 6
    transit byte totals:   receive 162, send 366
    transit packet drops:  receive 0, seq error 0, send 0
Router# show l2vpn atom vc
                                       Service
Interface Peer ID         VC ID      Type   Name                     Status
--------- --------------- ---------- ------ ------------------------ ----------
pw101     104.0.0.1       101        p2p    foo101                   UP 
Router# show l2vpn atom vc detail
pseudowire101 is up, VC status is up PW type: Ethernet
  Create time: 00:00:18, last status change time: 00:00:14
    Last label FSM state change time: 00:00:14
  Destination address: 104.0.0.1 VC ID: 101
    Output interface: Fa0/0/1, imposed label stack {16 17}
    Preferred path: not configured  
    Default path: active
    Next hop: 10.1.1.2
  Member of xconnect service foo101
    Associated member Se0/1/0:0 is up, status is up
    Interworking type is Ethernet
    Service id: 0xde000002
  Signaling protocol: LDP, peer 104.0.0.1:0 up
    Targeted Hello: 102.0.0.1(LDP Id) -> 104.0.0.1, LDP is UP
    Graceful restart: configured and enabled
    Non stop routing: not configured and not enabled
    PWid FEC (128), VC ID: 101
    Status TLV support (local/remote)         : enabled/supported
      LDP route watch                         : enabled
      Label/status state machine              : established, LruRru
      Local dataplane status received         : No fault
      BFD dataplane status received           : Not sent
      BFD peer monitor status received        : No fault
      Status received from access circuit     : No fault
      Status sent to access circuit           : No fault
      Status received from pseudowire i/f     : No fault
      Status sent to network peer             : No fault
      Status received from network peer       : No fault
      Adjacency status of remote peer         : No fault
  Sequencing: receive disabled, send disabled
  Bindings
    Parameter    Local                          Remote
    ------------ ------------------------------ ------------------------------
    Label        18                             17
    Group ID     0                              0
    Interface    Connect to CE1                 Connect to CE2                
    MTU          1500                           1500
    Control word on (configured: autosense)     on
    PW type      Ethernet                       Ethernet
    VCCV CV type 0x02                           0x02
                   LSPV [2]                       LSPV [2]                    
    VCCV CC type 0x07                           0x07
                   CW [1], RA [2], TTL [3]       CW [1], RA [2], TTL [3]
    Status TLV   enabled                        supported
  SSO Descriptor: 104.0.0.1/101, local label: 18
  Dataplane:
    SSM segment/switch IDs: 4106/4105 (used), PWID: 2
  Rx Counters
    3 input transit packets, 162 bytes
    0 drops, 0 seq err 
  Tx Counters
    5 output transit packets, 305 bytes
    0 drops

The following example shows how to verify the Ethernet configuration on PE: 


Router# show mpls l2transport vc
Local intf     Local circuit              Dest address    VC ID      Status
-------------  -------------------------- --------------- ---------- ----------
Gi1/0/0        Ethernet                   102.0.0.1       101        UP 
Router# show mpls l2transport vc detail
Local interface: Gi1/0/0 up, line protocol up, Ethernet up
  Destination address: 102.0.0.1, VC ID: 101, VC status: up
    Output interface: Fa0/0/1, imposed label stack {19 33}
    Preferred path: not configured  
    Default path: active
    Next hop: 11.1.1.1
  Create time: 00:00:22, last status change time: 00:00:19
    Last label FSM state change time: 00:00:19
  Signaling protocol: LDP, peer 102.0.0.1:0 up
    Targeted Hello: 104.0.0.1(LDP Id) -> 102.0.0.1, LDP is UP
    Graceful restart: configured and enabled
    Non stop routing: not configured and not enabled
    Status TLV support (local/remote)   : enabled/supported
      LDP route watch                   : enabled
      Label/status state machine        : established, LruRru
      Last local dataplane   status rcvd: No fault
      Last BFD dataplane     status rcvd: Not sent
      Last BFD peer monitor  status rcvd: No fault
      Last local AC  circuit status rcvd: No fault
      Last local AC  circuit status sent: No fault
      Last local PW i/f circ status rcvd: No fault
      Last local LDP TLV     status sent: No fault
      Last remote LDP TLV    status rcvd: No fault
      Last remote LDP ADJ    status rcvd: No fault
    MPLS VC labels: local 22, remote 33 
    Group ID: local 0, remote 0
    MTU: local 1500, remote 1500
    Remote interface description: Connect to CE1
  Sequencing: receive disabled, send disabled
  Control Word: On
  SSO Descriptor: 102.0.0.1/101, local label: 22
  Dataplane:
    SSM segment/switch IDs: 4574/4573 (used), PWID: 80
  VC statistics:
    transit packet totals: receive 9, send 5
    transit byte totals:   receive 315, send 380
    transit packet drops:  receive 0, seq error 0, send 0
Router# show l2vpn atom vc
                                       Service
Interface Peer ID         VC ID      Type   Name                     Status
--------- --------------- ---------- ------ ------------------------ ----------
pw101     102.0.0.1       101        p2p    foo101                   UP 
Router# show l2vpn atom vc detail
pseudowire101 is up, VC status is up PW type: Ethernet
  Create time: 00:00:23, last status change time: 00:00:20
    Last label FSM state change time: 00:00:20
  Destination address: 102.0.0.1 VC ID: 101
    Output interface: Fa0/0/1, imposed label stack {18 18}
    Preferred path: not configured  
    Default path: active
    Next hop: 11.1.1.1
  Member of xconnect service foo101
    Associated member Gi1/0/0 is up, status is up
    Interworking type is Like2Like
    Service id: 0xb5000004
  Signaling protocol: LDP, peer 102.0.0.1:0 up
    Targeted Hello: 104.0.0.1(LDP Id) -> 102.0.0.1, LDP is UP
    Graceful restart: configured and enabled
    Non stop routing: not configured and not enabled
    PWid FEC (128), VC ID: 101
    Status TLV support (local/remote)         : enabled/supported
      LDP route watch                         : enabled
      Label/status state machine              : established, LruRru
      Local dataplane status received         : No fault
      BFD dataplane status received           : Not sent
      BFD peer monitor status received        : No fault
      Status received from access circuit     : No fault
      Status sent to access circuit           : No fault
      Status received from pseudowire i/f     : No fault
      Status sent to network peer             : No fault
      Status received from network peer       : No fault
      Adjacency status of remote peer         : No fault
  Sequencing: receive disabled, send disabled
  Bindings
    Parameter    Local                          Remote
    ------------ ------------------------------ ------------------------------
    Label        17                             18
    Group ID     0                              0
    Interface    Connect to CE2                 Connect to CE1                
    MTU          1500                           1500
    Control word on (configured: autosense)     on
    PW type      Ethernet                       Ethernet
    VCCV CV type 0x02                           0x02
                   LSPV [2]                       LSPV [2]                    
    VCCV CC type 0x07                           0x07
                   CW [1], RA [2], TTL [3]       CW [1], RA [2], TTL [3]
    Status TLV   enabled                        supported
  SSO Descriptor: 102.0.0.1/101, local label: 17
  Dataplane:
    SSM segment/switch IDs: 4126/4125 (used), PWID: 4
  Rx Counters
    5 input transit packets, 175 bytes
    0 drops, 0 seq err 
  Tx Counters
    3 output transit packets, 228 bytes
    0 drops

VLAN (dot1q) mode

The following example shows how to verify the HDLC configuration on PE: 


Router# show mpls l2transport vc
Local intf     Local circuit              Dest address    VC ID      Status
-------------  -------------------------- --------------- ---------- ----------
Se0/1/0:0      HDLC                       104.0.0.1       138        UP        
Router# show mpls l2transport vc detail
Local interface: Se0/1/0:0 up, line protocol up, HDLC up
  Interworking type is Ethernet
  Destination address: 104.0.0.1, VC ID: 138, VC status: up
    Output interface: Fa0/0/1, imposed label stack {20 53}
    Preferred path: not configured  
    Default path: active
    Next hop: 10.1.1.2
  Create time: 00:00:19, last status change time: 00:00:15
    Last label FSM state change time: 00:00:15
  Signaling protocol: LDP, peer 104.0.0.1:0 up
    Targeted Hello: 102.0.0.1(LDP Id) -> 104.0.0.1, LDP is UP
    Graceful restart: configured and enabled
    Non stop routing: not configured and not enabled
    Status TLV support (local/remote)   : enabled/supported
      LDP route watch                   : enabled
      Label/status state machine        : established, LruRru
      Last local dataplane   status rcvd: No fault
      Last BFD dataplane     status rcvd: Not sent
      Last BFD peer monitor  status rcvd: No fault
      Last local AC  circuit status rcvd: No fault
      Last local AC  circuit status sent: No fault
      Last local PW i/f circ status rcvd: No fault
      Last local LDP TLV     status sent: No fault
      Last remote LDP TLV    status rcvd: No fault
      Last remote LDP ADJ    status rcvd: No fault
    MPLS VC labels: local 35, remote 53 
    Group ID: local 0, remote 0
    MTU: local 1500, remote 1500
    Remote interface description: Connect to CE2
  Sequencing: receive disabled, send disabled
  Control Word: On
  SSO Descriptor: 104.0.0.1/138, local label: 35
  Dataplane:
    SSM segment/switch IDs: 4486/4485 (used), PWID: 65
  VC statistics:
    transit packet totals: receive 4, send 3
    transit byte totals:   receive 1036, send 183
    transit packet drops:  receive 0, seq error 0, send 0
Router# show l2vpn atom vc
                                       Service
Interface Peer ID         VC ID      Type   Name                     Status
--------- --------------- ---------- ------ ------------------------ ----------
pw138     104.0.0.1       138        p2p    foo138                   UP 
Router# show l2vpn atom vc detail
pseudowire138 is up, VC status is up PW type: Ethernet
  Create time: 00:00:18, last status change time: 00:00:14
    Last label FSM state change time: 00:00:14
  Destination address: 104.0.0.1 VC ID: 138
    Output interface: Fa0/0/1, imposed label stack {16 30}
    Preferred path: not configured  
    Default path: active
    Next hop: 10.1.1.2
  Member of xconnect service foo138
    Associated member Se0/1/0:0 is up, status is up
    Interworking type is Ethernet
    Service id: 0x4000027
  Signaling protocol: LDP, peer 104.0.0.1:0 up
    Targeted Hello: 102.0.0.1(LDP Id) -> 104.0.0.1, LDP is UP
    Graceful restart: configured and enabled
    Non stop routing: not configured and not enabled
    PWid FEC (128), VC ID: 138
    Status TLV support (local/remote)         : enabled/supported
      LDP route watch                         : enabled
      Label/status state machine              : established, LruRru
      Local dataplane status received         : No fault
      BFD dataplane status received           : Not sent
      BFD peer monitor status received        : No fault
      Status received from access circuit     : No fault
      Status sent to access circuit           : No fault
      Status received from pseudowire i/f     : No fault
      Status sent to network peer             : No fault
      Status received from network peer       : No fault
      Adjacency status of remote peer         : No fault
  Sequencing: receive disabled, send disabled
  Bindings
    Parameter    Local                          Remote
    ------------ ------------------------------ ------------------------------
    Label        20                             30
    Group ID     0                              0
    Interface    Connect to CE1                 Connect to CE2                
    MTU          1500                           1500
    Control word on (configured: autosense)     on
    PW type      Ethernet                       Ethernet
    VCCV CV type 0x02                           0x02
                   LSPV [2]                       LSPV [2]                    
    VCCV CC type 0x07                           0x07
                   CW [1], RA [2], TTL [3]       CW [1], RA [2], TTL [3]
    Status TLV   enabled                        supported
  SSO Descriptor: 104.0.0.1/138, local label: 20
  Dataplane:
    SSM segment/switch IDs: 4313/4312 (used), PWID: 41
  Rx Counters
    2 input transit packets, 108 bytes
    0 drops, 0 seq err 
  Tx Counters
    3 output transit packets, 183 bytes
    0 drops

The following example shows how to verify the VLAN configuration on PE: 


Router# show mpls l2transport vc
Local intf     Local circuit              Dest address    VC ID      Status
-------------  -------------------------- --------------- ---------- ----------
Gi1/0/0.10     Eth VLAN 10                102.0.0.1       138        UP 
Router# show mpls l2transport vc detail
Local interface: Gi1/0/0.10 up, line protocol up, Eth VLAN 10 up
  Interworking type is Ethernet
  Destination address: 102.0.0.1, VC ID: 138, VC status: up
    Output interface: Fa0/0/1, imposed label stack {19 35}
    Preferred path: not configured  
    Default path: active
    Next hop: 11.1.1.1
  Create time: 00:00:22, last status change time: 00:00:20
    Last label FSM state change time: 00:00:20
  Signaling protocol: LDP, peer 102.0.0.1:0 up
    Targeted Hello: 104.0.0.1(LDP Id) -> 102.0.0.1, LDP is UP
    Graceful restart: configured and enabled
    Non stop routing: not configured and not enabled
    Status TLV support (local/remote)   : enabled/supported
      LDP route watch                   : enabled
      Label/status state machine        : established, LruRru
      Last local dataplane   status rcvd: No fault
      Last BFD dataplane     status rcvd: Not sent
      Last BFD peer monitor  status rcvd: No fault
      Last local AC  circuit status rcvd: No fault
      Last local AC  circuit status sent: No fault
      Last local PW i/f circ status rcvd: No fault
      Last local LDP TLV     status sent: No fault
      Last remote LDP TLV    status rcvd: No fault
      Last remote LDP ADJ    status rcvd: No fault
    MPLS VC labels: local 53, remote 35 
    Group ID: local 0, remote 0
    MTU: local 1500, remote 1500
    Remote interface description: Connect to CE1
  Sequencing: receive disabled, send disabled
  Control Word: On
  SSO Descriptor: 102.0.0.1/138, local label: 53
  Dataplane:
    SSM segment/switch IDs: 4784/4783 (used), PWID: 117
  VC statistics:
    transit packet totals: receive 6, send 6
    transit byte totals:   receive 234, send 1276
    transit packet drops:  receive 0, seq error 0, send 0
Router# show l2vpn atom vc
                                       Service
Interface Peer ID         VC ID      Type   Name                     Status
--------- --------------- ---------- ------ ------------------------ ----------
pw138     102.0.0.1       138        p2p    foo138                   UP 
Router# show l2vpn atom vc detail
pseudowire138 is up, VC status is up PW type: Ethernet
  Create time: 00:00:23, last status change time: 00:00:20
    Last label FSM state change time: 00:00:20
  Destination address: 102.0.0.1 VC ID: 138
    Output interface: Fa0/0/1, imposed label stack {18 20}
    Preferred path: not configured  
    Default path: active
    Next hop: 11.1.1.1
  Member of xconnect service foo138
    Associated member Gi1/0/0.10 is up, status is up
    Interworking type is Ethernet
    Service id: 0x7b000029
  Signaling protocol: LDP, peer 102.0.0.1:0 up
    Targeted Hello: 104.0.0.1(LDP Id) -> 102.0.0.1, LDP is UP
    Graceful restart: configured and enabled
    Non stop routing: not configured and not enabled
    PWid FEC (128), VC ID: 138
    Status TLV support (local/remote)         : enabled/supported
      LDP route watch                         : enabled
      Label/status state machine              : established, LruRru
      Local dataplane status received         : No fault
      BFD dataplane status received           : Not sent
      BFD peer monitor status received        : No fault
      Status received from access circuit     : No fault
      Status sent to access circuit           : No fault
      Status received from pseudowire i/f     : No fault
      Status sent to network peer             : No fault
      Status received from network peer       : No fault
      Adjacency status of remote peer         : No fault
  Sequencing: receive disabled, send disabled
  Bindings
    Parameter    Local                          Remote
    ------------ ------------------------------ ------------------------------
    Label        30                             20
    Group ID     0                              0
    Interface    Connect to CE2                 Connect to CE1                
    MTU          1500                           1500
    Control word on (configured: autosense)     on
    PW type      Ethernet                       Ethernet
    VCCV CV type 0x02                           0x02
                   LSPV [2]                       LSPV [2]                    
    VCCV CC type 0x07                           0x07
                   CW [1], RA [2], TTL [3]       CW [1], RA [2], TTL [3]
    Status TLV   enabled                        supported
  SSO Descriptor: 102.0.0.1/138, local label: 30
  Dataplane:
    SSM segment/switch IDs: 4333/4332 (used), PWID: 41
  Rx Counters
    8 input transit packets, 312 bytes
    0 drops, 0 seq err 
  Tx Counters
    5 output transit packets, 380 bytes
    0 drops

QinQ mode

The following example shows how to verify HDLC configuration on PE: 


Router# show mpls l2transport vc
Local intf     Local circuit              Dest address    VC ID      Status
-------------  -------------------------- --------------- ---------- ----------
Se0/1/0:0      HDLC                       104.0.0.1       145        UP        
Router# show mpls l2transport vc detail
Local interface: Se0/1/0:0 up, line protocol up, HDLC up
  Interworking type is Ethernet
  Destination address: 104.0.0.1, VC ID: 145, VC status: up
    Output interface: Fa0/0/1, imposed label stack {20 25}
    Preferred path: not configured  
    Default path: active
    Next hop: 10.1.1.2
  Create time: 00:00:20, last status change time: 00:00:15
    Last label FSM state change time: 00:00:15
  Signaling protocol: LDP, peer 104.0.0.1:0 up
    Targeted Hello: 102.0.0.1(LDP Id) -> 104.0.0.1, LDP is UP
    Graceful restart: configured and enabled
    Non stop routing: not configured and not enabled
    Status TLV support (local/remote)   : enabled/supported
      LDP route watch                   : enabled
      Label/status state machine        : established, LruRru
      Last local dataplane   status rcvd: No fault
      Last BFD dataplane     status rcvd: Not sent
      Last BFD peer monitor  status rcvd: No fault
      Last local AC  circuit status rcvd: No fault
      Last local AC  circuit status sent: No fault
      Last local PW i/f circ status rcvd: No fault
      Last local LDP TLV     status sent: No fault
      Last remote LDP TLV    status rcvd: No fault
      Last remote LDP ADJ    status rcvd: No fault
    MPLS VC labels: local 27, remote 25 
    Group ID: local 0, remote 0
    MTU: local 1500, remote 1500
    Remote interface description: Connect to CE2
  Sequencing: receive disabled, send disabled
  Control Word: On
  SSO Descriptor: 104.0.0.1/145, local label: 27
  Dataplane:
    SSM segment/switch IDs: 4521/4520 (used), PWID: 72
  VC statistics:
    transit packet totals: receive 4, send 7
    transit byte totals:   receive 216, send 427
    transit packet drops:  receive 0, seq error 0, send 0
Router# show l2vpn atom vc
                                       Service
Interface Peer ID         VC ID      Type   Name                     Status
--------- --------------- ---------- ------ ------------------------ ----------
pw145     104.0.0.1       145        p2p    foo145                   UP        
Router# show l2vpn atom vc detail
pseudowire145 is up, VC status is up PW type: Ethernet
  Create time: 00:00:18, last status change time: 00:00:13
    Last label FSM state change time: 00:00:13
  Destination address: 104.0.0.1 VC ID: 145
    Output interface: Fa0/0/1, imposed label stack {16 33}
    Preferred path: not configured  
    Default path: active
    Next hop: 10.1.1.2
  Member of xconnect service foo145
    Associated member Se0/1/0:0 is up, status is up
    Interworking type is Ethernet
    Service id: 0x2e
  Signaling protocol: LDP, peer 104.0.0.1:0 up
    Targeted Hello: 102.0.0.1(LDP Id) -> 104.0.0.1, LDP is UP
    Graceful restart: configured and enabled
    Non stop routing: not configured and not enabled
    PWid FEC (128), VC ID: 145
    Status TLV support (local/remote)         : enabled/supported
      LDP route watch                         : enabled
      Label/status state machine              : established, LruRru
      Local dataplane status received         : No fault
      BFD dataplane status received           : Not sent
      BFD peer monitor status received        : No fault
      Status received from access circuit     : No fault
      Status sent to access circuit           : No fault
      Status received from pseudowire i/f     : No fault
      Status sent to network peer             : No fault
      Status received from network peer       : No fault
      Adjacency status of remote peer         : No fault
  Sequencing: receive disabled, send disabled
  Bindings
    Parameter    Local                          Remote
    ------------ ------------------------------ ------------------------------
    Label        33                             33
    Group ID     0                              0
    Interface    Connect to CE1                 Connect to CE2                
    MTU          1500                           1500
    Control word on (configured: autosense)     on
    PW type      Ethernet                       Ethernet
    VCCV CV type 0x02                           0x02
                   LSPV [2]                       LSPV [2]                    
    VCCV CC type 0x07                           0x07
                   CW [1], RA [2], TTL [3]       CW [1], RA [2], TTL [3]
    Status TLV   enabled                        supported
  SSO Descriptor: 104.0.0.1/145, local label: 33
  Dataplane:
    SSM segment/switch IDs: 4345/4344 (used), PWID: 48
  Rx Counters
    2 input transit packets, 108 bytes
    0 drops, 0 seq err 
  Tx Counters
    3 output transit packets, 183 bytes
    0 drops

The following example shows how to verify the Qinq configuration on PE: 


Router# show mpls l2transport vc
Local intf     Local circuit              Dest address    VC ID      Status
-------------  -------------------------- --------------- ---------- ----------
Gi1/0/0.10     Eth VLAN 10/20             102.0.0.1       145        UP        
Router# show mpls l2transport vc detail
Local interface: Gi1/0/0.10 up, line protocol up, Eth VLAN 10/20 up
  Interworking type is Ethernet
  Destination address: 102.0.0.1, VC ID: 145, VC status: up
    Output interface: Fa0/0/1, imposed label stack {19 27}
    Preferred path: not configured  
    Default path: active
    Next hop: 11.1.1.1
  Create time: 00:00:23, last status change time: 00:00:21
    Last label FSM state change time: 00:00:21
  Signaling protocol: LDP, peer 102.0.0.1:0 up
    Targeted Hello: 104.0.0.1(LDP Id) -> 102.0.0.1, LDP is UP
    Graceful restart: configured and enabled
    Non stop routing: not configured and not enabled
    Status TLV support (local/remote)   : enabled/supported
      LDP route watch                   : enabled
      Label/status state machine        : established, LruRru
      Last local dataplane   status rcvd: No fault
      Last BFD dataplane     status rcvd: Not sent
      Last BFD peer monitor  status rcvd: No fault
      Last local AC  circuit status rcvd: No fault
      Last local AC  circuit status sent: No fault
      Last local PW i/f circ status rcvd: No fault
      Last local LDP TLV     status sent: No fault
      Last remote LDP TLV    status rcvd: No fault
      Last remote LDP ADJ    status rcvd: No fault
    MPLS VC labels: local 25, remote 27 
    Group ID: local 0, remote 0
    MTU: local 1500, remote 1500
    Remote interface description: Connect to CE1
  Sequencing: receive disabled, send disabled
  Control Word: On
  SSO Descriptor: 102.0.0.1/145, local label: 25
  Dataplane:
    SSM segment/switch IDs: 4815/4814 (used), PWID: 124
  VC statistics:
    transit packet totals: receive 10, send 6
    transit byte totals:   receive 430, send 456
    transit packet drops:  receive 0, seq error 0, send 0
Router# show l2vpn atom vc
                                       Service
Interface Peer ID         VC ID      Type   Name                     Status
--------- --------------- ---------- ------ ------------------------ ----------
pw145     102.0.0.1       145        p2p    foo145                   UP        
Router# show l2vpn atom vc detail
pseudowire145 is up, VC status is up PW type: Ethernet
  Create time: 00:00:23, last status change time: 00:00:19
    Last label FSM state change time: 00:00:19
  Destination address: 102.0.0.1 VC ID: 145
    Output interface: Fa0/0/1, imposed label stack {18 33}
    Preferred path: not configured  
    Default path: active
    Next hop: 11.1.1.1
  Member of xconnect service foo145
    Associated member Gi1/0/0.10 is up, status is up
    Interworking type is Ethernet
    Service id: 0xed000030
  Signaling protocol: LDP, peer 102.0.0.1:0 up
    Targeted Hello: 104.0.0.1(LDP Id) -> 102.0.0.1, LDP is UP
    Graceful restart: configured and enabled
    Non stop routing: not configured and not enabled
    PWid FEC (128), VC ID: 145
    Status TLV support (local/remote)         : enabled/supported
      LDP route watch                         : enabled
      Label/status state machine              : established, LruRru
      Local dataplane status received         : No fault
      BFD dataplane status received           : Not sent
      BFD peer monitor status received        : No fault
      Status received from access circuit     : No fault
      Status sent to access circuit           : No fault
      Status received from pseudowire i/f     : No fault
      Status sent to network peer             : No fault
      Status received from network peer       : No fault
      Adjacency status of remote peer         : No fault
  Sequencing: receive disabled, send disabled
  Bindings
    Parameter    Local                          Remote
    ------------ ------------------------------ ------------------------------
    Label        33                             33
    Group ID     0                              0
    Interface    Connect to CE2                 Connect to CE1                
    MTU          1500                           1500
    Control word on (configured: autosense)     on
    PW type      Ethernet                       Ethernet
    VCCV CV type 0x02                           0x02
                   LSPV [2]                       LSPV [2]                    
    VCCV CC type 0x07                           0x07
                   CW [1], RA [2], TTL [3]       CW [1], RA [2], TTL [3]
    Status TLV   enabled                        supported
  SSO Descriptor: 102.0.0.1/145, local label: 33
  Dataplane:
    SSM segment/switch IDs: 4361/4360 (used), PWID: 48
  Rx Counters
    8 input transit packets, 344 bytes
    0 drops, 0 seq err 
  Tx Counters
    5 output transit packets, 380 bytes
    0 drops

Example: HDLC-Dot1Q Interworking

The following example shows how to configure HDLC-dot1q interworking:

Short form

On HDLC-PE: 


configure terminal 
template type pseudowire hdlc-vlan1-tmp
 encapsulation mpls
 signaling protocol ldp
 
l2vpn xconnect context hdlc-vlan1
  interworking ethernet
  member Serial0/2/0:3
  member pseudowire101 192.0.2.3 107 template hdlc-vlan1-tmp
  no shutdown
end

On Ethernet-PE: 


configure terminal 
interface FastEthernet0/0/0.16
description Connect to CE2
encapsulation dot1q 16
no ip addres
no shut
!
template type pseudowire hdlc-vlan1-tmp
 encapsulation mpls
 signaling protocol ldp
  
l2vpn xconnect context hdlc-vlan1
  interworking ethernet
  member FastEthernet0/0/0.16
  member pseudowire101 192.0.2.1 107 template hdlc-vlan1-tmp
  no shutdown
end

Long form

On HDLC-PE: 


configure terminal 
template type pseudowire hdlc-vlan1
 encapsulation mpls
!
interface pseudowire107
 source template type pseudowire hdlc-vlan1
 encapsulation mpls
 neighbor 192.0.2.3 107
 signaling protocol ldp
 no shut
! 
l2vpn xconnect context hdlc-vlan1-con
  interworking ethernet
  member Serial0/2/0:3
  member pseudowire107 
  no shutdown
end

On Ethernet-PE: 


configure terminal 
interface FastEthernet0/0/0.16
description Connect to CE2
encapsulation dot1q 16
no ip addres
no shut
!
template type pseudowire hdlc-vlan1
 encapsulation mpls
!
interface pseudowire107
 source template type pseudowire hdlc-vlan1
 encapsulation mpls
 neighbor 192.0.2.1 107
 signaling protocol ldp
 no shut
! 
  
l2vpn xconnect context hdlc-vlan1-con
  interworking ethernet
  member FastEthernet0/0/0.16
  member pseudowire107
  no shutdown
end

Additional References

The following sections provide references related to the Frame Relay-to-ATM Bridged Interworking and xconnect support on GEC (VPWS) features.

Related Documents

Related Topic

Document Title

Basics of MPLS

{start cross reference}MPLS: Basic MPLS Configuration Guide, Cisco IOS XE Release 3S{end cross reference}

MPLS Layer 2 VPNs

{start cross reference}MPLS Layer 2 VPNs Configuration Guide, Cisco IOS XE Release 3S{end cross reference}

Cisco IOS Configuration Fundamentals

{start cross reference}Cisco IOS Configuration Fundamentals Command Reference{end cross reference}

Standards

Standard

Title

No new or modified standards are supported by this feature.

—

MIBs

MIB

MIBs Link

  • CISCO-IETF-PW-MIB
  • CISCO-IETF-PW-MPLS-MIB

To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use the Cisco MIB Locator found at the following URL:

{start hypertext}http://www.cisco.com/go/mibs{end hypertext}

RFCs

RFC{start superscript}1{end superscript}

Title

RFC 2684

Multiprotocol Encapsulation over ATM Adaptation Layer 5

RFC 2427

Multiprotocol Interconnect over Frame Relay

{start footnote}Not all the supported RFCs are listed.{end footnote}

Technical Assistance

Description

Link

The Cisco Support website provides extensive online resources, including documentation and tools for troubleshooting and resolving technical issues with Cisco products and technologies.

To receive security and technical information about your products, you can subscribe to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds.

Access to most tools on the Cisco Support website requires a Cisco.com user ID and password.

{start hypertext}http://www.cisco.com/cisco/web/support/index.html{end hypertext}

Feature Information for Configuring MPLS Layer 2 VPNs

{start cross reference}Table 17-2{end cross reference} lists the features in this module and provides links to specific configuration information. Only features that were introduced or modified in Cisco IOS Release 3.6.0S or a later release appear in the table.

Not all commands may be available in your Cisco IOS software release. For release information about a specific command, see the corresponding command reference documentation.

Use the Cisco Feature Navigator to find information about platform support and software image support. The Cisco Feature Navigator enables you to determine which Cisco IOS and Cisco Catalyst operating system software images support a specific software release, feature set, or platform. To access the Cisco Feature Navigator, go to {start hypertext}http://www.cisco.com/go/cfn{end hypertext}. An account on Cisco.com is not required.

Table 2. Feature Information for Configuring MPLS Layer 2 VPNs

Feature Name

Releases

Feature Information

Frame Relay to ATM Bridged Interworking

3.6.0S

The Frame Relay to ATM Bridged Interworking feature provides interoperability between the Frame Relay attachment VC and the ATM attachment VC connected to different PE routers. The bridged encapsulation corresponding to the bridged (Ethernet) interworking mechanism is used. The Ethernet frames are carried through the MPLS network using Ethernet over MPLS (EoMPLS).

In Cisco IOS XE Release 3.6.0S, this feature was implemented on the Cisco ASR 1000 Series Aggregation Services Routers.

The following sections provide information about this feature:

  • {start cross reference}Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking{end cross reference}
  • {start cross reference}Configuring Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking{end cross reference}

xconnect support on GEC (VPWS) on ASR1000

3.6.0S

The Xconnect Support on GEC (VPWS) on ASR1000 feature enables the service providers to supply connectivity between customer sites with existing data link layer (Layer 2) networks by using a single, integrated, packet-based network infrastructure—a Cisco MPLS network. Instead of separate networks with network management environments, service providers can deliver Layer 2 connections over an MPLS backbone.

In Cisco IOS XE Release 3.6.0S, this feature was implemented on the ASR 1000 Series Aggregation Services Routers.

The following sections provide information about this feature:

  • {start cross reference}Gigabit EtherChannel for Virtual Private Wire Service{end cross reference}
  • {start cross reference}Configuring Gigabit EtherChannel for Virtual Private Wire Service{end cross reference}

Reverse Layer 2 Gateway Protocol

3.8.0S

Reverse L2GP (R-L2GP) is a variation of L2GP. In case of R-L2GP, the pseudo information of the R-L2GP is transmitted by nPEs, instead of uPEs. R-L2GP provides a mechanism to send out static preconfigured BPDUs on each ring access port of nPEs to stimulate a per-access ring instantiation of the protocol. R-L2GP enables the PEs to avoid the burden of running Multiple-instance Spanning Tree Protocol (MST) when multiple independent access networks that run MST connect to a pair of redundant PEs. In order for this to work, the pair of nPEs are programmed to send out BPDUs on the access ring ports in such a way that they appear to be either:

  • The root bridge itself (the bridge with the lowest bridge id/priority).
  • The bridge with the second lowest bridge ID/priority, and with a 0 cost path to the root.

The following sections provide information about this feature:

  • {start cross reference}Reverse Layer 2 Gateway Protocol{end cross reference}
  • {start cross reference}Configuring the R-L2GP{end cross reference}

HDLC-Ethernet Interworking

3.13.0S

High-Level Data Link Control (HDLC)-Ethernet over MPLS is part of Any Transport over MPLS (AToM) solution. HDLC and Ethernet are two link-layer transport systems that utilize the AToM architecture. The feature describes how these two transport system can communicate with each other using the AToM framework.

The following sections provide information about this feature:

  • {start cross reference}High-Level Data Link Control-Ethernet Interworking{end cross reference}
  • {start cross reference}Configuring HDLC-Ethernet Interworking{end cross reference}

Glossary

ATM —Asynchronous Transfer Mode. A method of data transportation, whereby fixed-length packets are sent over a switched network. The method’s ability to ensure reliable delivery of packets at a high rate makes it suitable for carrying voice, video, and data.

AToM —Any Transport over MPLS. AToM is a solution for transporting Layer 2 packets over an MPLS backbone. AToM enables service providers to supply connectivity between customer sites with existing data link layer (Layer 2) networks by using a single, integrated, packet-based network infrastructure—a Cisco MPLS network. Instead of separate networks with separate network management environments, service providers can deliver Layer 2 connections over an MPLS backbone.

Dot1q —IEEE 802.1Q is the networking standard that supports virtual LANs (VLANs) on an Ethernet network. The standard defines a system of VLAN tagging for Ethernet frames and the accompanying procedures to be used by bridges and switches in handling such frames.

EoMPLS —Ethernet over MPLS. This technology leverages an existing MPLS backbone network to deliver Transparent LAN Services based on Ethernet connectivity to the customer site.

GEC —Gigabit EtherChannel. A high-performance Ethernet technology that provides gigabit per second transmission rates. It provides a flexible and scalable bandwidth with resiliency and load sharing across links for switches, router interfaces, and servers. Supports up to eight links per channel.

HDLC —High-Level Data Link Control (HDLC) is a bit-oriented code-transparent synchronous data link-layer protocol developed by the International Organization for Standardization (ISO).

MPLS —Multiprotocol Label Switching. A mechanism in high-performance telecommunications networks that directs and carries data from one network node to the next. MPLS makes it easy to create virtual links between distant nodes. It can encapsulate packets of various network protocols.

QinQ —IEEE 802.1ad is an Ethernet networking standard informally known as IEEE 802.1QinQ, and is an amendment to the IEEE standard 802.1Q-1998. The technique is also known as provider bridging, Stacked VLANs, or simply QinQ or Q-in-Q.

VPLS —Virtual Private LAN Service. A method to provide Ethernet-based multipoint-to-multipoint communication over IP and MPLS networks.