The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
This module provides conceptual and configuration information for point-to-point Layer 2 (L2) connectivity.
These point-to-point services are supported:
Local Switching—A point-to-point circuit internal to a single Cisco ASR 9000 Series Router, also known as local connect.
Pseudowires—A virtual point-to-point circuit from a Cisco ASR 9000 Series Router. Pseudowires are implemented over MPLS.
 Note |
Point to Point Layer 2 Services are also called as MPLS Layer 2 VPNs. |
Note |
For more information about Point to Point Layer 2 Services on the Cisco ASR 9000 Series Router and for descriptions of the commands listed in this module, see the “Related Documents” section. |
| Release | Modification |
|---|---|
|
Release 3.7.2 |
This feature was introduced. |
|
Release 3.9.0 |
Scale enhancements were introduced. |
|
Release 4.0.0 |
Support was added for Any Transport over MPLS (AToM) features. |
|
Release 4.0.1 |
Support was added for these features:
|
|
Release 4.1.0 |
Support was added for the Flexible Router ID feature. |
|
Release 4.2.0 |
Support was added for these features:
|
|
Release 4.3.0 |
Support was added for the L2VPN Nonstop Routing feature. |
|
Release 4.3.1 |
Support was added for these features:
|
|
Release 5.1.0 |
Support was added for these features:
|
|
Release 5.1.2 |
Support was added for the following:
|
You must be in a user group associated with a task group that includes the proper task IDs. The command reference guides include the task IDs required for each command.
If you suspect user group assignment is preventing you from using a command, contact your AAA administrator for assistance.
To implement Point to Point Layer 2 Services, you should understand these concepts:
Layer 2 Virtual Private Network (L2VPN) emulates the behavior of a LAN across an L2 switched, IP or MPLS-enabled IP network, allowing Ethernet devices to communicate with each other as they would when connected to a common LAN segment. Point-to-point L2 connections are vital when creating L2VPNs.
As Internet service providers (ISPs) look to replace their Frame Relay or Asynchronous Transfer Mode (ATM) infrastructures with an IP infrastructure, there is a need to provide standard methods of using an L2 switched, IP or MPLS-enabled IP infrastructure. These methods provide a serviceable L2 interface to customers; specifically, to provide virtual circuits between pairs of customer sites.
Building a L2VPN system requires coordination between the ISP and the customer. The ISP provides L2 connectivity; the customer builds a network using data link resources obtained from the ISP. In an L2VPN service, the ISP does not require information about a the customer's network topology, policies, routing information, point-to-point links, or network point-to-point links from other ISPs.
The ISP requires provider edge (PE) routers with these capabilities:
Encapsulation of L2 protocol data units (PDU) into Layer 3 (L3) packets.
Interconnection of any-to-any L2 transports.
Emulation of L2 quality-of-service (QoS) over a packet switch network.
Ease of configuration of the L2 service.
Support for different types of tunneling mechanisms (MPLS, L2TPv3, IPSec, GRE, and others).
L2VPN process databases include all information related to circuits and their connections.
Local switching allows you to switch L2 data between two interfaces of the same type, (for example, Ethernet to Ethernet) and on the same router. The interfaces can be on the same line card, or on two different line cards. During these types of switching, Layer 2 address is used instead of the Layer 3 address. A local switching connection switches L2 traffic from one attachment circuit (AC) to the other. The two ports configured in a local switching connection are ACs with respect to that local connection. A local switching connection works like a bridge domain that has only two bridge ports; traffic enters one port of the local connection and leaves the other. However, because there is no bridging involved in a local connection, there is neither MAC learning nor flooding. Also, the ACs in a local connection are not in the UP state if the interface state is DOWN. (This behavior is also different when compared to that of a bridge domain.)
Local switching ACs utilize a full variety of L2 interfaces, including L2 trunk (main) interfaces, bundle interfaces, and EFPs.
Additionally, same-port local switching allows you to switch Layer 2 data between two circuits on the same interface.
ATMoMPLS is a type of Layer 2 point-to-point connection over an MPLS core.
To implement the ATMoMPLS feature, the Cisco ASR 9000 Series Router plays the role of provider edge (PE) router at the edge of a provider network in which customer edge (CE) devices are connected to the Cisco ASR 9000 Series Router.
Virtual Circuit Connection Verification (VCCV) is an L2VPN Operations, Administration, and Maintenance (OAM) feature that allows network operators to run IP-based provider edge-to-provider edge (PE-to-PE) keepalive protocol across a specified pseudowire to ensure that the pseudowire data path forwarding does not contain any faults. The disposition PE receives VCCV packets on a control channel, which is associated with the specified pseudowire. The control channel type and connectivity verification type, which are used for VCCV, are negotiated when the pseudowire is established between the PEs for each direction.
Two types of packets can arrive at the disposition egress:
Type 1—Specifies normal Ethernet-over-MPLS (EoMPLS) data packets.
Type 2—Specifies VCCV packets.
Cisco ASR 9000 Series Router supports Label Switched Path (LSP) VCCV Type 1, which uses an inband control word if enabled during signaling. The VCCV echo reply is sent as IPv4 that is the reply mode in IPv4. The reply is forwarded as IP, MPLS, or a combination of both.
VCCV pings counters that are counted in MPLS forwarding on the egress side. However, on the ingress side, they are sourced by the route processor and do not count as MPLS forwarding counters.
Ethernet-over-MPLS (EoMPLS) provides a tunneling mechanism for Ethernet traffic through an MPLS-enabled L3 core and encapsulates Ethernet protocol data units (PDUs) inside MPLS packets (using label stacking) to forward them across the MPLS network.
EoMPLS features are described in these subsections:
In Ethernet port mode, both ends of a pseudowire are connected to Ethernet ports. In this mode, the port is tunneled over the pseudowire or, using local switching (also known as an attachment circuit-to-attachment circuit cross-connect) switches packets or frames from one attachment circuit (AC) to another AC attached to the same PE node.
The following figure provides an example of Ethernet port mode.
In VLAN mode, each VLAN on a customer-end to provider-end link can be configured as a separate L2VPN connection using virtual connection (VC) type 4 or VC type 5. VC type 5 is the default mode.
As illustrated in the following figure, the Ethernet PE associates an internal VLAN-tag to the Ethernet port for switching the traffic internally from the ingress port to the pseudowire; however, before moving traffic into the pseudowire, it removes the internal VLAN tag.
At the egress VLAN PE, the PE associates a VLAN tag to the frames coming off of the pseudowire and after switching the traffic internally, it sends out the traffic on an Ethernet trunk port.
Note |
Because the port is in trunk mode, the VLAN PE doesn't remove the VLAN tag and forwards the frames through the port with the added tag. |
Inter-AS is a peer-to-peer type model that allows extension of VPNs through multiple provider or multi-domain networks. This lets service providers peer up with one another to offer end-to-end VPN connectivity over extended geographical locations.
EoMPLS support can assume a single AS topology where the pseudowire connecting the PE routers at the two ends of the point-to-point EoMPLS cross-connects resides in the same autonomous system; or multiple AS topologies in which PE routers can reside on two different ASs using iBGP and eBGP peering.
The following figure illustrates MPLS over Inter-AS with a basic double AS topology with iBGP/LDP in each AS.
QinQ is an extension of 802.1Q for specifying multiple 802.1Q tags (IEEE 802.1QinQ VLAN Tag stacking). Layer 3 VPN service termination and L2VPN service transport are enabled over QinQ sub-interfaces.
The Cisco ASR 9000 Series Routers implement the Layer 2 tunneling or Layer 3 forwarding depending on the subinterface configuration at provider edge routers. This function only supports up to two QinQ tags on the SPA and fixed PLIM:
Layer 2 QinQ VLANs in L2VPN attachment circuit: QinQ L2VPN attachment circuits are configured under the Layer 2 transport subinterfaces for point-to-point EoMPLS based cross-connects using both virtual circuit type 4 and type 5 pseudowires and point-to-point local-switching-based cross-connects including full interworking support of QinQ with 802.1q VLANs and port mode.
Layer 3 QinQ VLANs: Used as a Layer 3 termination point, both VLANs are removed at the ingress provider edge and added back at the remote provider edge as the frame is forwarded.
Layer 3 services over QinQ include:
IPv4 unicast and multicast
IPv6 unicast and multicast
MPLS
Connectionless Network Service (CLNS) for use by Intermediate System-to-Intermediate System (IS-IS) Protocol
In QinQ mode, each CE VLAN is carried into an SP VLAN. QinQ mode should use VC type 5, but VC type 4 is also supported. On each Ethernet PE, you must configure both the inner (CE VLAN) and outer (SP VLAN).
The following figure illustrates QinQ using VC type 4.
In the QinAny mode, the service provider VLAN tag is configured on both the ingress and the egress nodes of the provider edge VLAN. QinAny mode is similar to QinQ mode using a Type 5 VC, except that the customer edge VLAN tag is carried in the packet over the pseudowire, as the customer edge VLAN tag is unknown.
Using L2VPN technology, you can assign a quality of service (QoS) level to both Port and VLAN modes of operation.
L2VPN technology requires that QoS functionality on PE routers be strictly L2-payload-based on the edge-facing interfaces (also know as attachment circuits). The following figure illustrates L2 and L3 QoS service policies in a typical L2VPN network.
The following figure shows four packet processing paths within a provider edge device where a QoS service policy can be attached. In an L2VPN network, packets are received and transmitted on the edge-facing interfaces as L2 packets and transported on the core-facing interfaces as MPLS (EoMPLS).
L2VPN uses control planes in both route processors and line cards, as well as forwarding plane elements in the line cards.
The availability of L2VPN meets these requirements:
A control plane failure in either the route processor or the line card will not affect the circuit forwarding path.
The router processor control plane supports failover without affecting the line card control and forwarding planes.
L2VPN integrates with existing Label Distribution Protocol (LDP) graceful restart mechanism.
Preferred tunnel path functionality lets you map pseudowires to specific traffic-engineering tunnels. Attachment circuits are cross-connected to specific MPLS traffic engineering tunnel interfaces instead of remote PE router IP addresses (reachable using IGP or LDP). Using preferred tunnel path, it is always assumed that the traffic engineering tunnel that transports the L2 traffic runs between the two PE routers (that is, its head starts at the imposition PE router and its tail terminates on the disposition PE router).
Note |
|
Pseudowires transport Layer 2 protocol data units (PDUs) across a public switched network (PSN). A multisegment pseudowire is a static or dynamically configured set of two or more contiguous pseudowire segments. These segments act as a single pseudowire, allowing you to:
Manage the end-to-end service by separating administrative or provisioning domains.
Keep IP addresses of provider edge (PE) nodes private across interautonomous system (inter-AS) boundaries. Use IP address of autonomous system boundary routers (ASBRs) and treat them as pseudowire aggregation routers. The ASBRs join the pseudowires of the two domains.
A multisegment pseudowire can span either an inter-AS boundary or two multiprotocol label switching (MPLS) networks.
A pseudowire is a tunnel between two PE nodes. There are two types of PE nodes:
A Switching PE (S-PE) node
Terminates PSN tunnels of the preceding and succeeding pseudowire segments in a multisegment pseudowire.
Switches control and data planes of the preceding and succeeding pseudowire segments of the multisegment pseudowire.
A Terminating PE (T-PE) node
Located at both the first and last segments of a multisegment pseudowire.
Where customer-facing attachment circuits (ACs) are bound to a pseudowire forwarder.
Note |
Every end of a multisegment pseudowire must terminate at a T-PE. |
A multisegment pseudowire is used in two general cases when:
It is not possible to establish a PW control channel between the source and destination PE nodes.
For the PW control channel to be established, the remote PE node must be accessible. Sometimes, the local PE node may not be able to access the remote node due to topology, operational, or security constraints.
A multisegment pseudowire dynamically builds two discrete pseudowire segments and performs a pseudowire switching to establish a PW control channel between the source and destination PE nodes.
Pseudowire Edge To Edge Emulation (PWE3) signaling and encapsulation protocols are different.
The PE nodes are connected to networks employing different PW signaling and encapsulation protocols. Sometimes, it is not possible to use a single segment PW.
A multisegment pseudowire, with the appropriate interworking performed at the PW switching points, enables PW connectivity between the PE nodes in the network.
Pseudowire redundancy allows you to configure your network to detect a failure in the network and reroute the Layer 2 service to another endpoint that can continue to provide service. This feature provides the ability to recover from a failure of either the remote provider edge (PE) router or the link between the PE and customer edge (CE) routers.
L2VPNs can provide pseudowire resiliency through their routing protocols. When connectivity between end-to-end PE routers fails, an alternative path to the directed LDP session and the user data takes over. However, there are some parts of the network in which this rerouting mechanism does not protect against interruptions in service.
Pseudowire redundancy enables you to set up backup pseudowires. You can configure the network with redundant pseudowires and redundant network elements.
Prior to the failure of the primary pseudowire, the ability to switch traffic to the backup pseudowire is used to handle a planned pseudowire outage, such as router maintenance.
Note |
Pseudowire redundancy is provided only for point-to-point Virtual Private Wire Service (VPWS) pseudowires. |
To maximize networks while maintaining redundancy typically requires traffic load balancing over multiple links. To achieve better and more uniformed distribution, load balancing on the traffic flows that are part of the provisioned pipes is desirable. Load balancing can be flow based according to the IP addresses, Mac addresses, or a combination of those. Load balancing can be flow based according to source or destination IP addresses, or source or destination MAC addresses. Traffic falls back to default flow based MAC addresses if the IP header cannot proceed or IPv6 is be flow based.
This feature applies to pseudowires under L2VPN; this includes VPWS and VPLS.
Note |
Enabling virtual circuit (VC) label based load balancing for a pseudowire class overrides global flow based load balancing under L2VPN. |
If the frame is IP-based, the load-balancing flow “src-dst-ip” configuration causes the Layer 2 interfaces to use the IP header for flow balancing hash calculation. If the frame is not IP-based, the MAC header is used for the hash calculation. In previous releases, for an MPLS header between the MAC and IP headers, the code would use the MAC header for the flow balancing hash.
From Release 6.4.1 onwards, the code analyzes the MPLS header, and if an IP header is available, it uses that for hash calculation.
If the MPLS label stack is more than four labels deep, the code stops looking for an IP header and reverts to the MAC header hash calculation.
When L2VPN flow-based src-dst-ip load-balancing is configured, and if a payload with encapsulated GTP is used, the GTP ID is considered for load-balancing criteria. Starting from Release 6.5.1, you do not have to configure the cef load-balancing command to use GTP ID as a criteria for load-balancing for L2VPN scenarios. However, you must explicitly configure CEF load-balancing for Layer 3 scenarios.
When pseudowires (PWs) are established, each PW is assigned a group ID that is common for all PWs created on the same physical port. When a physical port becomes non-functional or disabled, Automatic Protection Switching (APS) signals the peer router to get activated and L2VPN sends a single message to advertise the status change of all PWs that have the Group ID associated with the physical port. A single L2VPN signal thus avoids a lot of processing and loss in reactivity.
For CEM interfaces, various levels of configuration are permitted for the parent controllers, such as T1 and T3, framed or unframed. To achieve best grouping, the physical controller handle is used as the group ID.
Note |
Pseudowire grouping is disabled by default. |
An Ethernet Wire Service is a service that emulates a point-to-point Ethernet segment. This is similar to Ethernet private line (EPL), a Layer 1 point-to-point service, except the provider edge operates at Layer 2 and typically runs over a Layer 2 network. The EWS encapsulates all frames that are received on a particular UNI and transports these frames to a single-egress UNI without reference to the contents contained within the frame. The operation of this service means that an EWS can be used with VLAN-tagged frames. The VLAN tags are transparent to the EWS (bridge protocol data units [BPDUs])—with some exceptions. These exceptions include IEEE 802.1x, IEEE 802.2ad, and IEEE 802.3x, because these frames have local significance and it benefits both the customer and the Service Provider to terminate them locally.
Since the service provider simply accepts frames on an interface and transmits these without reference to the actual frame (other than verifying that the format and length are legal for the particular interface) the EWS is indifferent to VLAN tags that may be present within the customer Ethernet frames.
EWS subscribes to the concept of all-to-one bundling. That is, an EWS maps a port on one end to a point-to-point circuit and to a port on another end. EWS is a port-to-port service. Therefore, if a customer needs to connect a switch or router to n switches or routers it will need n ports and n pseudowires or logical circuits.
One important point to consider is that, although the EWS broadly emulates an Ethernet Layer 1 connection, the service is provided across a shared infrastructure, and therefore it is unlikely that the full interface bandwidth will be, or needs to be, available at all times. EWS will typically be a sub-line rate service, where many users share a circuit somewhere in their transmission path. As a result, the cost will most likely be less than that of EPL. Unlike a Layer 1 EPL, the SP will need to implement QoS and traffic engineering to meet the specific objectives of a particular contract. However, if the customer's application requires a true wire rate transparent service, then an EPL service—delivered using optical transmission devices such as DWDM (dense wavelength division multiplexing), CDWM (coarse wavelength division multiplexing), or SONET/SDH—should be considered.
IGMP snooping provides a way to constrain multicast traffic at Layer 2. By snooping the IGMP membership reports sent by hosts in the bridge domain, the IGMP snooping application can set up Layer 2 multicast forwarding tables to deliver traffic only to ports with at least one interested member, significantly reducing the volume of multicast traffic.
Configured at Layer 3, IGMP provides a means for hosts in an IPv4 multicast network to indicate which multicast traffic they are interested in and for routers to control and limit the flow of multicast traffic in the network (at Layer 3).
IGMP snooping uses the information in IGMP membership report messages to build corresponding information in the forwarding tables to restrict IP multicast traffic at Layer 2. The forwarding table entries are in the form <Route, OIF List>, where:
Route is a <*, G> route or <S, G> route.
OIF List comprises all bridge ports that have sent IGMP membership reports for the specified route plus all Multicast Router (mrouter) ports in the bridge domain.
The IGMP snooping feature can provide these benefits to a multicast network:
Basic IGMP snooping reduces bandwidth consumption by reducing multicast traffic that would otherwise flood an entire VPLS bridge domain.
With optional configuration options, IGMP snooping can provide security between bridge domains by filtering the IGMP reports received from hosts on one bridge port and preventing leakage towards the hosts on other bridge ports.
With optional configuration options, IGMP snooping can reduce the traffic impact on upstream IP multicast routers by suppressing IGMP membership reports (IGMPv2) or by acting as an IGMP proxy reporter (IGMPv3) to the upstream IP multicast router.
Refer to the Implementing Layer 2 Multicast with IGMP Snooping module in the Cisco ASR 9000 Series Aggregation Services Router Multicast Configuration Guide for information on configuring IGMP snooping.
The applicable IGMP snooping commands are described in the Cisco ASR 9000 Series Aggregation Services Router Multicast Command Reference.
Customer deployments require a solution to support AToM with disparate transport at network ends. This solution must have the capability to translate transport on one customer edge (CE) device to another transport, for example, Frame relay to Ethernet. The Cisco ASR 9000 Series SPA Interface Processor-700 and the Cisco ASR 9000 Series Ethernet line cards enable the Cisco ASR 9000 Series Routers to support multiple legacy services.
IP Interworking is a solution for transporting Layer 2 traffic over an IP/MPLS backbone. It accommodates many types of Layer 2 frames such as Ethernet and Frame Relay using AToM tunnels. It encapsulates packets at the provider edge (PE) router, transports them over the backbone to the PE router on the other side of the cloud, removes the encapsulation, and transports them to the destination. The transport layer can be Ethernet on one end and Frame relay on the other end. IP interworking occurs between disparate endpoints of the AToM tunnels.
Note |
Only routed interworking is supported between Ethernet and Frame Relay based networks for MPLS and Local-connect scenarios. |
The following figure shows the interoperability between an Ethernet attachment VC and a Frame Relay attachment VC.
An attachment circuit (AC) is a physical or logical port or circuit that connects a CE device to a PE device. A pseudowire (PW) is a bidirectional virtual connection (VC) connecting two ACs. In an MPLS network, PWs are carried inside an LSP tunnel. The core facing line card on the PE1 and PE2 could be a Cisco ASR 9000 Series SPA Interface Processor-700 or a Cisco ASR 9000 Series Ethernet line card.
In the IP Interworking mode, the Layer 2 (L2) header is removed from the packets received on an ingress PE, and only the IP payload is transmitted to the egress PE. On the egress PE, an L2 header is appended before the packet is transmitted out of the egress port.
In Figure above , CE1 and CE2 could be a Frame Relay (FR) interface or a GigabitEthernet (GigE) interface. Assuming CE1 is a FR and CE2 is either a GigE or dot1q, or QinQ. For packets arriving from an Ethernet CE (CE2), ingress LC on the PE (PE2) facing the CE removes L2 framing and forwards the packet to egress PE (PE1) using IPoMPLS encapsulation over a pseudowire. The core facing line card on egress PE removes the MPLS labels but preserves the control word and transmits it to the egress line card facing FR CE (CE1). At the FR PE, after label disposition, the Layer 3 (L3) packets are encapsulated over FR.
Similarly, IP packets arriving from the FR CE are translated into IPoMPLS encapsulation over the pseudowire. At the Ethernet PE side, after label disposition, the PE adds L2 Ethernet packet header back to the packet before transmitting it to the CE, as the packets coming out from the core carry only the IP payload.
These modes support IP Interworking on AToM:
Ethernet to Frame Relay
Packets arriving from the Ethernet CE device have MAC (port-mode, untagged, single, double tag), IPv4 header and data. The Ethernet line card removes the L2 framing and then forwards the L3 packet to the egress line card. The egress line card adds the FR L2 header before transmitting it from the egress port.
Ethernet to Ethernet
Both the CE devices are Ethernet. Each ethernet interface can be port-mode, untagged, single, or double tag, although this is not a typical scenario for IP interworking.
This feature enables an interworking layer in the access network(s) to terminate all non-Ethernet functionality and translate these connections to a Ethernet centric service which can be terminated on the Layer 3 edge routers. Currently, the time-division multiplexing (TDM) based services terminate on the Layer 3 edge routers directly. A simplified and more cost optimized model for the L3 networks is enabled by moving the TDM complexity into the access layer.
The Layer 2 encapsulation is removed from an IP packet by the ingress PE’s attachment circuit facing ingress line card. The MPLS encapsulated IP packet payload is then sent across the fabric to the core facing egress line card. The egress line card then transmits the packet through the MPLS core. On the remote PE, the MPLS label is removed, Layer 2 header of the egress AC is added and finally the packet is sent to the connected CE. L2VPN VPWS has been enhanced to support:
Point-to-Point Protocol (PPP)
High-level Data Link Control (HDLC)
Multilink Point-to-Point Protocol (MLPPP)
QOS support for all the encapsulation types
For more information on QoS, see the Cisco ASR 9000 Series Aggregation Services Router Modular Quality of Service Configuration.
The TDM ACs can be configured on these SPAs:
SPA-8XCHT1/E1
SPA-4XCT3/DS0
SPA-1XCHSTM1/OC3
SPA-2XCHOC12/DS0
SPA-1XCHOC48/DS3
SPA-4XT3/E3
SPA-4XOC3-POS-V2
SPA-8XOC3-POS
SPA-8XOC12-POS
SPA-1XOC48POS/RPR
SPA-2XOC48POS/RPR
Any Transport over MPLS (AToM) transports Layer 2 packets over a Multiprotocol Label Switching (MPLS) backbone. This enables service providers to connect customer sites with existing Layer 2 networks by using a single, integrated, packet-based network infrastructure. Using this feature, service providers can deliver Layer 2 connections over an MPLS backbone, instead of using separate networks.
AToM encapsulates Layer 2 frames at the ingress PE router, and sends them to a corresponding PE router at the other end of a pseudowire, which is a connection between the two PE routers. The egress PE removes the encapsulation and sends out the Layer 2 frame.
The successful transmission of the Layer 2 frames between PE routers is due to the configuration of the PE routers. You set up a connection, called a pseudowire, between the routers. You specify this information on each PE router:
The type of Layer 2 data that will be transported across the pseudowire, such as Ethernet and Frame Relay
The IP address of the loopback interface of the peer PE router, which enables the PE routers to communicate.
A unique combination of peer PE IP address and VC ID that identifies the pseudowire.
The control word contains forward explicit congestion notification (FECN), backward explicit congestion notification (BECN) and DE bits in case of frame relay connection.
Control word is mandatory for:
Frame Relay
ATM AAL5
Frame Relay to Ethernet bridged interworking
cHDLC/PPP IP interworking
CEM (Circuit Emulation)
The system does not map bits from one transport end point to another across an AToM IP Interworking connection.
Whenever supported, control word is also recommended for pseudowires, as it enables proper load balancing without packet desequencing independent of L2VPN packet content. Without control word the heuristics used to perform load balancing cannot achieve optimal results in all cases.
The attachment circuit (AC) is a main interface configured with HDLC encapsulation. Packets to or from the AC are transported using an AToM pseudowire (PW) of VC type 0x6 to or from the other provider edge (PE) router over the MPLS core network.
With HDLC over MPLS, the entire HDLC packet is transported. The ingress PE router removes only the HDLC flags and FCS bits.
The attachment circuit (AC) is a main interface configured with PPP encapsulation. Packets to or from the AC are transported through an AToM PW of VC type 0x7 to or from the other provider edge (PE) routers over the MPLS core network.
With PPP over MPLS, the ingress PE router removes the flags, address, control field, and the FCS bits.
Frame Relay over MPLS (FRoMPLS) provides leased line type of connectivity between two Frame Relay islands. Frame Relay traffic is transported over the MPLS network.
Note |
The Data Link Connection Identifier (DLCI) DCLI-DLCI mode is supported. A control word (required for DLCI-DLCI mode) is used to carry additional control information. |
When a Provider Edge (PE) router receives a Frame Relay protocol packet from a subscriber site, it removes the Frame Relay header and Frame Check Sequence (FCS) and appends the appropriate Virtual Circuit (VC) label. The removed Backward Explicit Congestion Notification (BECN), Forward Explicit Congestion Notification (FECN), Discard Eligible (DE) and Command/Response (C/R) bits are (for DLCI-DLCI mode) sent separately using a control word.
MPLS transport profile (MPLS-TP) tunnels provide the transport network service layer over which IP and MPLS traffic traverse. Within the MPLS-TP environment, pseudowires (PWs) use MPLS-TP tunnels as the transport mechanism. MPLS-TP tunnels help transition from SONET/SDH TDM technologies to packet switching, to support services with high bandwidth utilization and low cost. Transport networks are connection oriented, statically provisioned, and have long-lived connections. Transport networks usually avoid control protocols that change identifiers (like labels). MPLS-TP tunnels provide this functionality through statically provisioned bidirectional label switched paths (LSPs).
For more information on configuring MPLS transport profile, refer to the Cisco ASR 9000 Series Aggregation Services Router MPLS Configuration Guide.
MPLS-TP supports these combinations of static and dynamic multisegment pseudowires:
Static-static
Static-dynamic
Dynamic-static
Dynamic-dynamic
MPLS-TP supports one-to-one L2VPN pseudowire redundancy for these combinations of static and dynamic pseudowires:
Static pseudowire with a static backup pseudowire
Static pseudowire with a dynamic backup pseudowire
Dynamic pseudowire with a static backup pseudowire
Dynamic pseudowire with a dynamic backup pseudowire
The existing TE preferred path feature is used to pin down a PW to an MPLS-TP transport tunnel. See Configuring Preferred Tunnel Path for more information on configuring preferred tunnel path. For a dynamic pseudowire, PW status is exchanged through LDP whereas for static PW, status is transported in PW OAM message. See Configuring PW Status OAM for more information on configuring PW status OAM. By default, alarms are not generated when the state of a PW changes due to change in the state of MPLS TP tunnel carrying that PW.
Circuit Emulation over Packet (CEoP) is a method of carrying TDM circuits over packet switched network. CEoP is similar to a physical connection. The goal of CEoP is to replace leased lines and legacy TDM networks.
CEoP operates in two major modes:
Unstructured mode is called SAToP (Structure Agnostic TDM over Packet)
SAToP addresses only structure-agnostic transport, i.e., unframed E1, T1, E3 and T3. It segments all TDM services as bit streams and then encapsulates them for transmission over a PW tunnel. This protocol can transparently transmit TDM traffic data and synchronous timing information. SAToP completely disregards any structure and provider edge routers (PEs) do not need to interpret the TDM data or to participate in the TDM signaling. The protocol is a simple way for transparent transmission of PDH bit-streams.
Structured mode is named CESoPSN (Circuit Emulation Service over Packet Switched Network)
Compared with SAToP, CESoPSN transmits emulated structured TDM signals. That is, it can identify and process the frame structure and transmit signaling in TDM frames. It may not transmit idle timeslot channels, but only extracts useful timeslots of CE devices from the E1 traffic stream and then encapsulates them into PW packets for transmission.CEoP SPAs are half-height (HH) Shared Port Adapters (SPA) and the CEoP SPA family consists of 24xT1/E1, 2xT3/E3, and 1xOC3/STM1 unstructured and structured (NxDS0) quarter rate, half height SPAs.
The CEM functionality is supported only on Engine 5 line cards having CEoP SPAs. CEM is supported on:
1-port Channelized OC3 STM1 ATM CEoP SPA (SPA-1CHOC3-CE-ATM)
CESoPSN and SAToP can use MPLS, UDP/IP, and L2TPv3 as the underlying transport mechanism. This release supports only MPLS transport mechanism.
CEoP SPA supports these modes of operation:
Circuit Emulation Mode (CEM)
ATM Mode
IMA Mode
Note |
Only CEM mode is supported. |
CEM offers these benefits to the service provider and end-users:
Saving cost in installing equipment.
Saving cost in network operations; as leased lines are expensive, limiting their usage to access only mode saves significant costs.
Ensuring low maintenance cost because only the core network needs to be maintained.
Utilizing the core network resources more efficiently with packet switched network, while keeping investment in access network intact.
Providing cheaper services to the end-user.
The L2VPN Nonstop Routing (NSR) feature avoids label distribution path (LDP) sessions from flapping on events such as process failures (crash) and route processor failover (RP FO). NSR on process failure (crash) is supported by performing RP FO, if you have enabled NSR using NSR process failure switchover.
NSR enables the router (where failure has occurred) to maintain the control plane states without a graceful restart (GR). NSR, by definition, does not require any protocol extension and typically uses Stateful Switch Over (SSO) to maintain it’s control plane states.
A L2TPv3 over IPv6 tunnel is a static L2VPN cross-connect that uses Layer 2 Tunneling Protocol version 3 (L2TPv3) over IPv6, with a unique IPv6 source address for each cross-connect. The L2TPv3 over IPv6 tunnels consists of one L2TPv3 tunnel for each subscriber VLAN. The unique IPv6 address completely identifies the customer, and the service that is delivered.
Note |
L2TPv3 over IPv6 tunnels are supported on the ASR 9000 Enhanced Ethernet line cards by a scale of 15000 crossconnects for each router and line card. |
Note |
nV satellite access interfaces do not support L2TPv3 over IPv6. |
L2TPv3 defines the L2TP protocol for tunneling Layer 2 payloads over an IP core network using Layer 2 virtual private networks (VPNs). Traffic between two customer network sites is encapsulated in IP packets carrying L2TP data messages (payload) and sent across an IP network. The backbone routers of the IP network treat this payload in the same manner as it treats any other IP traffic. Implementing L2TPv3 over IPv6 provides an opportunity to utilize unique source IPv6 addresses to directly identify Ethernet attachment circuits. In this case, processing of the L2TPv3 session ID is bypassed; this is because each tunnel has only one associated session. This local optimization, however, does not hinder the ability to continue supporting circuit multiplexing through the session ID for other L2TPv3 tunnels on the same router.
For more information on:
Configuration procedures, see Configuring L2TPv3 over IPv6Tunnels.
Configuration examples, see Configuring L2TPv3 over IPv6 Tunnels: Example.
Traffic Injection from L2TPv3 over IPv6 Tunnel feature allows you to inject diagnostic traffic through Layer 2 Tunneling Protocol version 3 (L2TPv3) Switched Port Analyzer (SPAN) tunnel. The diagnostic traffic allows you to monitor and troubleshoot the network traffic. You can send the diagnostic traffic from customer office (CO) using traffic generator towards the customer or towards the network.
In previous releases, with traffic mirroring feature the user was only able to send the mirrored traffic from customer towards the monitoring device, the mirror tunnel was unidirectional.
Traffic mirroring copies traffic from one or more source ports and sends the copied traffic to one or more destinations for analysis by a network analyzer or other monitoring device. Traffic mirroring does not affect the flow of traffic on the source interfaces or sub-interfaces, and allows the mirrored traffic to be sent to a destination interface or sub-interface
This feature is not supported on bundle and sub-bundle interfaces, supported only on main and sub interfaces.
Diagnostic traffic directed from network to customer does not traverse the same path as the actual non-diagnostic network to customer traffic. As a result, any issue with the core facing interface is not diagnosed.
Diagnostic traffic will mix with the actual customer traffic. It is the responsibility of CO to ensure that it does not cause any problems to the customer, and CO is able to differentiate diagnostic traffic from customer traffic in the SPAN tunnel.
Physical port features are not available in the inward inject path, so the problems in the physical port features, such as, EOAM or BIA MAC are not diagnosed.
Bundle and other hash calculations, such as, ECMP, are not available, so the only customer interface supported is a physical interface.
For Layer 3, only IPv4 and IPv6 diagnostic payload is supported.
Consider a topology where an L2TPv3 tunnel is created between two ASR 9000 devices. Customer Office (CO) sends diagnostic traffic using traffic generator over L2TPv3 over IPv6 tunnel to the ASR 9000 router. The ASR 9000 router on the left-hand side sends the diagnostic traffic towards the customer as though it is sent from the network or sends the diagnostic traffic towards the network as though it is sent from the customer.
The diagnostic traffic header contains destination MAC address, source MAC address, and IP payload. If the header contains destination MAC address of the ASR 9000 router, the diagnostic traffic is sent to the network as though it sent from the customer. If the header contains source MAC address of the ASR 9000 router, the diagnostic traffic is sent to the customer as though it sent from the network.
Create a pseudowire monitor session with inject interface
Attach the monitor session to an interface which needs to be spanned
Configure L2VPN xconnect with monitor session
/* Create a pseudowire monitor session with inject interface */
Router# configure
Router(config)# monitor-session span1
Router(config-mon)# destination pseudowire
Router(config-mon)# inject-interface tenGigE 0/1/0/0/0
Router(config-mon)# commit
Router(config-mon)# end
/* Attach the monitor session to an interface which needs to be spanned */
Router# configure
Router(config)# int tenGigE 0/1/0/0/0
Router(config-subif)# monitor-session span1 ethernet
Router(config-if-mon)# commit
/* Configure L2VPN xconnect with monitor session */
Router(config)# l2vpn
Router(config-l2vpn)# xconnect group xc-span1
Router(config-l2vpn-xc)# p2p span-session1
Router(config-l2vpn-xc-p2p)# monitor-session span1
Router(config-l2vpn-xc-p2p)# neighbor ipv6 1112::1:1 pw-id 101
Router(config-l2vpn-xc-p2p-pw)# pw-class ts
Router(config-l2vpn-xc-p2p-pw)# source 1111::1:1
Router(config-l2vpn-xc-p2p-pw)# l2tp static local cookie size 8 value 0x1 0xa1 local session 101
Router(config-l2vpn-xc-p2p-pw)# l2tp static remote cookie size 8 value 0xa1 0x1 remote session 101
Router(config-l2vpn-xc-p2p-pw)# commit
Router(config-l2vpn-xc-p2p-pw)# end
configure
monitor-session span1
destination pseudowire
inject-interface tenGigE 0/1/0/0/0
!
!
configure
int tenGigE 0/1/0/0/0
monitor-session span1 ethernet
!
!
l2vpn
xconnect group xc-span1
p2p span-session1
monitor-session span1
neighbor ipv6 1112::1:1 pw-id 101
pw-class ts
source 1111::1:1
l2tp static
local cookie size 8 value 0x1 0xa1
local session 101
remote cookie size 8 value 0xa1 0x1
remote session 101
!
!
!
Verify that the source MAC address and destination MAC address are matching.
/* Verify that the source MAC address is matching */
Router#show monitor-session span1 counters
Monitor-session span1
TenGigE0/1/0/0/0.1
Rx replicated: 248 packets, 247086 octets
Tx replicated: 20001 packets, 20000094 octets
Non-replicated: 0 packets, 0 octets
Router#show interface tenGigE 0/1/0/7/8 accounting
TenGigE0/1/0/7/8.1
Protocol Pkts In Chars In Pkts Out Chars Out
IPV6_UNICAST 10001 10480072 10005 10480632
IPV6_MULTICAST 1 104 0 0
IPV6_ND 2 212 1 72
Router#show interface tenGigE 0/1/0/0/0 accounting
TenGigE0/1/0/0/0.1
Protocol Pkts In Chars In Pkts Out Chars Out
IPV6_UNICAST 2 136 10002 9780144
IPV6_ND
/* Verify that the destination MAC address is matching */
Router#show monitor-session counters
Monitor-session span1
TenGigE0/1/0/0/0.1
Rx replicated: 10001 packets, 10000094 octets
Tx replicated: 1 packets, 94 octets
Non-replicated: 0 packets, 0 octets
Router#show interface tenGigE 0/1/0/7/8 accounting
TenGigE0/1/0/7/8.1
Protocol Pkts In Chars In Pkts Out Chars Out
IPV6_UNICAST 10000 10480000 10000 10480000
IPV6_MULTICAST 0 0 1 104
IPV6_ND 0 0 1 104
Router#show interface tenGigE 0/1/0/0/0 accounting
TenGigE0/1/0/0/0.1
Protocol Pkts In Chars In Pkts Out Chars Out
IPV6_UNICAST 10000 9780000 0 0
IPV6_ND 1 82 1 72
Layer 2 Tunneling Protocol version 3 (L2TPv3) over IPv4 provides a dynamic mechanism for tunneling Layer 2 (L2) circuits across a packet-oriented data network, with multiple attachment circuits multiplexed over a single pair of IP address endpoints, using the L2TPv3 session ID as a circuit discriminator.
The following figure shows how the L2TPv3 feature is used to set up VPNs using Layer 2 tunneling over an IP network. All traffic between two customer network sites is encapsulated in IP packets carrying L2TP data messages and sent across an IP network. The backbone routers of the IP network treat the traffic as any other IP traffic and needn’t know anything about the customer networks.
In the above figure the PE routers R1 and R2 provide L2TPv3 services. The R1 and R2 routers communicate with each other using a pseudowire over the IP backbone network through a path comprising the interfaces int1 and int2 , the IP network, and interfaces int3 and int4 . The CE routers R3 and R4 communicate through a pair of cross-connected Ethernet or 802.1q VLAN interfaces using an L2TPv3 session. The L2TPv3 session tu1 is a pseudowire configured between interface int1 on R1 and interface int4 on R2. Any packet arriving on interface int1 on R1 is encapsulated and sent through the pseudowire control-channel (tu1) to R2. R2 decapsulates the packet and sends it on interface int4 to R4. When R4 needs to send a packet to R3, the packet follows the same path in reverse.
Note |
L2TPv3 over IPv4 feature is supported only on Cisco ASR 9000 High Density 100GE Ethernet line cards. |
Note |
nV satellite access interfaces do not support L2TPv3 over IPv4. |
For more information on:
Configuration procedures, see Configuring L2TPv3 over IPv4 Tunnels.
Configuration examples, see Configuring L2TPv3 over IPv4 Tunnels: Example.
A single-segment pseudowire (SS-PW) is a point-to-point pseudowire (PW) where the PW segment is present between two PE routers.
In this feature, a single-segment pseudowire is established between two PE routers of the same autonomous system (AS) dynamically using the FEC 129 information. The objective of this feature is to ensure interoperability of the Cisco routers with the third-party routers.
The T-PE on which the SS-PW is initiated and the signaling message is transmitted from is called as the source-terminating PE (ST-PE). The T-PE that waits and responds to the SS-PW signaling message is called the target-terminating PE (TT-PE).
The signaling flow from the ST-PE to TT-PE is referred to as the forward direction signaling or the active signaling. The signaling flow from the TT-PE to ST-PE is referred to as the reverse direction signaling or the passive signaling.
Generally, the PE with the highest prefix address takes the active role and becomes the ST-PE, and the other PE becomes the passive TT-PE.
The following figure illustrates the SS-PW signaling flow between ST-PE and TT-PE:
The dynamic discovery of the pseudowire path from the ST-PE to the T-PE is achieved using the L2 route table. The route table entries, that is, a list of prefix and associated next-hops to the L2VPN are populated by BGP.
Note |
In Release 5.1.2, Cisco supports only the routable prefix to reach the TAII on the T-PE. The routable prefix is the neighbor address of the targeted-LDP session. The reachability of packets from the source to the destination is achieved by user configurations (see Configuring L2VPN Single Segment Pseudowire) However, BGP supports MS-PW Subsequent Address Family Identifiers (SAFI) that is used to exchange the L2 routes across all the PEs. SS-PW uses the BGP MS-PW address family to function. To ensure interoperability with other third-party routers, Cisco advertises a single BGP MS-PW route per T-PE where the value of AC-ID (attachment circuit-identifier) is a wild-card entry. |
The supported pseudowire features are pw-status, pw-grouping, and tag-impose vlan.
The following figure illustrates the E-line Services Network with SS-PWs:
Configuring MPLS Label Distribution Protocol.
Configuring Interior Gateway Protocol (IGP).
Configure Border Gateway Protocol (BGP).
Configuring an Interface or Connection for L2VPN.
The routed pseudowire can only be enabled on Virtual Private Wire Service (VPWS) cross connects.
A cross-connect cannot have both ends configured as “neighbor routed” pseudowire.
SS-PW is not supported as the other member of the cross-connect, that is, at a T-PE, one end of the cross-connect can be the termination of the SS-PW and the other end can either be an attachment circuit (AC) or a PW-HE.
Source AII and AC-ID (attachment circuit identifier) are unique per router.
L2TP and MPLS static are not supported.
To configure single segment pseudowire in the network, do the following:
(Optional) Configuring the related L2VPN Global Parameters. See Configuring L2VPN Global Parameters
This procedure is used to overwrite the default BGP Route Distinguisher (RD) auto-generated value and also the Autonomous System Number (ASN) and Route Identifier (RID) of BGP.
Configuring L2VPN MS-PW Address Family Under BGP
The address family is configured under BGP to exchange the dynamic pseudowire routes.
Perform this task to configure L2VPN global parameters.
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
|
Step 2 |
l2vpn Example:Enters Layer 2 VPN configuration mode. |
|
Step 3 |
router-id router-id Example:Specifies the router ID. |
|
Step 4 |
pw-routing Example:Enables pseudowire routing capabilities and enters the pseudowire routing configuration submode |
|
Step 5 |
global-id global-id Example:Configures the L2VPN global ID value for the router. |
|
Step 6 |
bgp Example:Enables the BGP pseudowire routing capabilities and enters the BGP configuration submode. |
|
Step 7 |
rd route-distinguisher Example:Configures the BGP route distinguisher. |
|
Step 8 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
Perform this task to configure L2VPN VPWS SS-PWs.
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
|
Step 2 |
interface typeinterface-path-id Example:Enters interface configuration mode and configures an interface. |
|
Step 3 |
l2vpn Example:Enters Layer 2 VPN configuration mode. |
|
Step 4 |
xconnect group group-name Example:Configures a cross-connect group name using a free-format 32-character string. |
|
Step 5 |
p2p xconnect-name Example:Enters P2P configuration submode. |
|
Step 6 |
interface type interface-path-id Example:Specifies the interface type and instance. |
|
Step 7 |
neighbor routed global-id: prefix: ac-id source ac-id Example:Enables pseudowire routing configuration submode for the p2p cross-connect. |
|
Step 8 |
(optional) pw-class class-name Example:Enters pseudowire class submode, allowing you to define a pseudowire class template. |
|
Step 9 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
Perform this task to configure L2VPN MS-PW address family under BGP:
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
|
Step 2 |
router bgp autonomous-system-number Example:Enters router configuration mode for the specified routing process. |
|
Step 3 |
address-family l2vpn mspw Example:Specifies the L2VPN address family and enters address family configuration mode. |
|
Step 4 |
neighbor ip-address Example:Adds the IP address of the neighbor in the specified autonomous system. |
|
Step 5 |
address-family l2vpn mspw Example:Specifies the L2VPN address family of the neighbor and enters address family configuration mode. |
|
Step 6 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
The EVPN-VPWS is a BGP control plane solution for point-to-point services. It implements the signaling and encapsulation techniques for establishing an EVPN instance between a pair of PEs. It has the ability to forward traffic from one network to another without MAC lookup. The use of EVPN for VPWS eliminates the need for signaling single-segment and multi-segment PWs for point-to-point Ethernet services. You can also configure the PWHE interface and a bridge domain access pseudowire using EVPN-VPWS.
EVPN-VPWS single homed technology works on IP and MPLS core; IP core to support BGP and MPLS core for switching packets between the endpoints.
The EVPN-VPWS single homed solution requires per EVI Ethernet Auto Discovery route. EVPN defines a new BGP Network Layer Reachability Information (NLRI) used to carry all EVPN routes. BGP Capabilities Advertisement used to ensure that two speakers support EVPN NLRI (AFI 25, SAFI 70) as per RFC 4760.
The architecture for EVPN VPWS is that the PEs run Multi-Protocol BGP in control-plane. The following image describes the EVPN-VPWS configuration:
The VPN ID (EVI)
The local AC identifier (AC1) that identifies the local end of the emulated service.
The remote AC identifier (AC2) that identifies the remote end of the emulated service.
PE1 allocates a MPLS label per local AC for reachability.
The VPWS service on PE2 is set in the same manner as PE1. The three same elements are required and the service configuration must be symmetric.
PE2 allocates a MPLS label per local AC for reachability.
PE1 advertise a single EVPN per EVI Ethernet AD route for each local endpoint (AC) to remote PEs with the associated MPLS label.
PE2 performs the same task.
On reception of EVPN per EVI EAD route from PE2, PE1 adds the entry to its local L2 RIB. PE1 knows the path list to reach AC2, for example, next hop is PE2 IP address and MPLS label for AC2.
PE2 performs the same task.
Scalability is achieved without signaling pseudowires.
Ease of provisioning
Pseudowires (PWs) are not used.
Leverages BGP best path selection (optimal forwarding).
Ensure BGP is configured for EVPN SAFI.
BGP session between PEs with 'address-family l2vpn evpn' to exchange EVPN routes.
The VPN ID is unique per router.
When specifying a list of route targets, they must be unique per PE (per BGP address-family).
On versions earlier than IOS XR release 6.7.1, MTU is not signaled and the MTU mismatch is ignored with no interoperability issues.
On versions starting from IOS XR release 6.7.1, L3 MTU is advertised by default and the MTU mismatch is enforced by default.
On versions earlier than IOS XR release 7.0.x, MTU is not signaled and the MTU mismatch is ignored with no interoperability issues.
On versions later than IOS XR release 7.0.x, L3 MTU is advertised by default and the MTU mismatch is enforced by default. But this results in interoperability issues with IOS XR release 7.3.2, if transmit-l2-mtu is configured since L3 and L2 MTUs do not match. You can configure transmit-mtu-zero and ignore-mtu-mismatch commands to avoid this situation.
On versions later than IOS XR release 7.3.2, MTU of 0 is advertised by default, and the MTU mismatch is ignored by default. L2 MTU can be advertised using the transmit-l2-mtu command, and MTU mismatch can be enforced with enforce-mtu-mismatch command.
This section describes the tasks required to implement Point to Point Layer 2 Services:
Perform this task to configure an interface or a connection for Point to Point Layer 2 Services.
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
|
Step 2 |
interface type interface-path-id Example:Enters interface configuration mode and configures an interface. |
|
Step 3 |
l2transport Example:Enables L2 transport on the selected interface. |
|
Step 4 |
exit Example:Exits the current configuration mode. |
|
Step 5 |
interface type interface-path-id Example:Enters interface configuration mode and configures an interface. |
|
Step 6 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
|
Step 7 |
show interface type interface-id Example:(Optional) Displays the configuration settings you committed for the interface. |
Perform this task to configure local switching.
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
|
Step 2 |
l2vpn Example:Enters L2VPN configuration mode. |
|
Step 3 |
xconnect group group-name Example:Enters the name of the cross-connect group. |
|
Step 4 |
p2p xconnect-name Example:Enters a name for the point-to-point cross-connect. |
|
Step 5 |
interface type interface-path-id Example:Specifies the interface type ID. The choices are:
|
|
Step 6 |
interface type interface-path-id Example:Specifies the interface type ID. The choices are:
|
|
Step 7 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
Perform this task to configure local connection redundancy.
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
||
|
Step 2 |
l2vpn Example:Enters L2VPN configuration mode. |
||
|
Step 3 |
xconnect group group-name Example:Enters the name of the cross-connect group. |
||
|
Step 4 |
p2p xconnect-name Example:Enters a name for the point-to-point cross-connect. |
||
|
Step 5 |
backup interface type interface-path-id Example:Configures local connect redundancy.
|
||
|
Step 6 |
interface type interface-path-id Example:Specifies the interface type ID. The choices are:
|
||
|
Step 7 |
interface type interface-path-id Example:Specifies the interface type ID. The choices are:
|
||
|
Step 8 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
Note |
|
Note |
Static pseudowire connections do not use LDP for signaling. |
Perform this task to configure static point-to-point cross-connects.
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
||
|
Step 2 |
l2vpn Example:Enters L2VPN configuration mode. |
||
|
Step 3 |
xconnect group group-name Example:Enters the name of the cross-connect group. |
||
|
Step 4 |
p2p xconnect-name Example:Enters a name for the point-to-point cross-connect. |
||
|
Step 5 |
interface type interface-path-id Example:Specifies the interface type and instance. |
||
|
Step 6 |
neighbor A.B.C.D pw-id pseudowire-id Example:Configures the pseudowire segment for the cross-connect. Use the A.B.C.D argument to specify the IP address of the cross-connect peer.
Optionally, you can disable the control word or set the transport-type to Ethernet or VLAN. |
||
|
Step 7 |
mpls static label local { value } remote { value } Example:Configures local and remote label ID values. |
||
|
Step 8 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
Perform this task to configure dynamic point-to-point cross-connects.
Note |
For dynamic cross-connects, LDP must be up and running. |
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
|
Step 2 |
l2vpn Example:Enters L2VPN configuration mode. |
|
Step 3 |
xconnect group group-name Example:Enters the name of the cross-connect group. |
|
Step 4 |
p2p xconnect-name Example:Enters a name for the point-to-point cross-connect. |
|
Step 5 |
interface type interface-path-id Example:Specifies the interface type ID. The choices are:
|
|
Step 6 |
neighbor A.B.C.D pw-id pseudowire-id Example:Configures the pseudowire segment for the cross-connect. Optionally, you can disable the control word or set the transport-type to Ethernet or VLAN. |
|
Step 7 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
The Inter-AS configuration procedure is identical to the L2VPN cross-connect configuration tasks (see “Configuring Static Point-to-Point Cross-Connects” section and “Configuring Dynamic Point-to-Point Cross-Connects” section) except that the remote PE IP address used by the cross-connect configuration is now reachable through iBGP peering.
Note |
You must be knowledgeable about IBGP, EBGP, and ASBR terminology and configurations to complete this configuration. |
This section describes how to configure L2VPN quality of service (QoS) in port mode and mode, VLAN mode, Frame Relay and ATM sub-interfaces.
The l2transport command cannot be used with any IP address, L3, or CDP configuration.
This procedure describes how to configure an L2VPN QoS policy in port mode.
Note |
In port mode, the interface name format does not include a subinterface number; for example, GigabitEthernet0/1/0/1. |
|
Step 1 |
configure Example: |
|
Step 2 |
interface type interface-path-id Example:Specifies the interface attachment circuit. |
|
Step 3 |
l2transport Example:Configures an interface or connection for L2 switching. |
|
Step 4 |
service-policy [ input | output ] [ policy-map-name ] Example:Attaches a QoS policy to an input or output interface to be used as the service policy for that interface. |
|
Step 5 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
|
Step 6 |
show qos interface type interface-id service-policy [ input | output ] [ policy-map-name ] Example:(Optional) Displays the QoS service policy you defined. |
This procedure describes how to configure a L2VPN QoS policy in VLAN mode.
Note |
In VLAN mode, the interface name must include a subinterface. For example: GigabitEthernet0/1/0/1.1. The l2transport command must follow the interface type on the same CLI line. For example: interface GigabitEthernet 0/0/0/0.1 l2transport”. |
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
||
|
Step 2 |
interface type interface-path-id.subinterface l2transport Example:Configures an interface or connection for L2 switching.
|
||
|
Step 3 |
service-policy [ input | output ] [ policy-map-name ] Example:Attaches a QoS policy to an input or output interface to be used as the service policy for that interface. |
||
|
Step 4 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
This section describes these tasks:
Configure a multisegment pseudowire as a point-to-point (p2p) cross-connect. For more information on P2P cross-connects, see the “Configuring Static Point-to-Point Cross-Connects".
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
||
|
Step 2 |
l2vpn Example:Enters L2VPN configuration mode. |
||
|
Step 3 |
xconnect group group-name Example:Configures a cross-connect group name using a free-format 32-character string. |
||
|
Step 4 |
p2p xconnect-name Example:Enters P2P configuration submode. |
||
|
Step 5 |
neighbor A.B.C.D pw-id value Example:Configures a pseudowire for a cross-connect. The IP address is that of the corresponding PE node. The pw-id must match the pw-id of the PE node.
|
||
|
Step 6 |
pw-class class-name Example:Enters pseudowire class submode, allowing you to define a pseudowire class template. |
||
|
Step 7 |
exit Example:Exits pseudowire class submode and returns the router to the parent configuration mode. |
||
|
Step 8 |
neighbor A.B.C.D pw-id value Example:Configures a pseudowire for a cross-connect. The IP address is that of the corresponding PE node. The pw-id must match the pw-id of the PE node. |
||
|
Step 9 |
pw-class class-name Example:Enters pseudowire class submode, allowing you to define a pseudowire class template. |
||
|
Step 10 |
commit Example:Saves configuration changes to the running configuration file and remains in the configuration session. |
S-PE nodes must have a description in the Pseudowire Switching Point Type-Length-Value (TLV). The TLV records all the switching points the pseudowire traverses, creating a helpful history for troubleshooting.
Each multisegment pseudowire can have its own description. For instructions, see the “Provisioning a Cross-Connect Description". If it does not have one, this global description is used.
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
|
Step 2 |
l2vpn Example:Enters L2VPN configuration mode. |
|
Step 3 |
description value Example:Populates the Pseudowire Switching Point TLV. This TLV records all the switching points the pseudowire traverses. Each multisegment pseudowire can have its own description. If it does not have one, this global description is used. |
|
Step 4 |
commit Example:Saves configuration changes to the running configuration file and remains in the configuration session. |
S-PE nodes must have a description in the Pseudowire Switching Point TLV. The TLV records all the switching points the pseudowire traverses, creating a history that is helpful for troubleshooting.
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
|
Step 2 |
l2vpn Example:Enters L2VPN configuration mode. |
|
Step 3 |
xconnect group group-name Example:Configures a cross-connect group name using a free-format 32-character string. |
|
Step 4 |
p2p xconnect-name Example:Enters P2P configuration submode. |
|
Step 5 |
description value Example:Populates the Pseudowire Switching Point TLV. This TLV records all the switching points the pseudowire traverses. Each multisegment pseudowire can have its own description. If it does not have one, a global description is used. For more information, see the “Provisioning a Multisegment Pseudowire Configuration". |
|
Step 6 |
commit Example:Saves configuration changes to the running configuration file and remains in the configuration session. |
For security purposes, the TLV can be hidden, preventing someone from viewing all the switching points the pseudowire traverses.
Virtual Circuit Connection Verification (VCCV) may not work on multisegment pseudowires with the switching-tlv parameter set to “hide”. For more information on VCCV, see the “Virtual Circuit Connection Verification on L2VPN".
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
|
Step 2 |
l2vpn Example:Enters L2VPN configuration mode. |
|
Step 3 |
pw-class class-name Example:Enters pseudowire class submode, allowing you to define a pseudowire class template. |
|
Step 4 |
encapsulation mpls Example:Sets pseudowire encapsulation to MPLS. |
|
Step 5 |
protocol ldp Example:Sets pseudowire signaling protocol to LDP. |
|
Step 6 |
switching-tlv hide Example:Sets pseudowire TLV to hide. |
|
Step 7 |
commit Example:Saves configuration changes to the running configuration file and remains in the configuration session. |
Use the pw-status command after you enable the pw-status command. The pw-status command is disabled by default. Changing the pw-status command reprovisions all pseudowires configured under L2VPN.
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
||
|
Step 2 |
l2vpn Example:Enters Layer 2 VPN configuration mode. |
||
|
Step 3 |
pw-status Example:Enables all pseudowires configured on this Layer 2 VPN.
|
||
|
Step 4 |
commit Example:Saves configuration changes to the running configuration file and remains in the configuration session. |
Pseudowire redundancy allows you to configure a backup pseudowire in case the primary pseudowire fails. When the primary pseudowire fails, the PE router can switch to the backup pseudowire. You can elect to have the primary pseudowire resume operation after it becomes functional.
These topics describe how to configure pseudowire redundancy:
Perform this task to configure point-to-point pseudowire redundancy for a backup delay.
|
Step 1 |
configure Example:Enters configuration mode. |
|
Step 2 |
l2vpn Example:Enters L2VPN configuration mode. |
|
Step 3 |
pw-class class-name Example:Configures the pseudowire class name. |
|
Step 4 |
backup disable {delay value | never} Example:This command specifies how long the primary pseudowire should wait after it becomes active to take over from the backup pseudowire.
|
|
Step 5 |
exit Example:Exits the current configuration mode. |
|
Step 6 |
xconnect group group-name Example:Enters the name of the cross-connect group |
|
Step 7 |
p2p {xconnect-name} Example:Enters a name for the point-to-point cross-connect. |
|
Step 8 |
neighbor A.B.C.D pw-id value Example:Configures the pseudowire segment for the cross-connect. |
|
Step 9 |
pw-class class-name Example:Configures the pseudowire class name. |
|
Step 10 |
backup {neighbor A.B.C.D} {pw-id value} Example:Configures the backup pseudowire for the cross-connect.
|
|
Step 11 |
end or commit Example:Saves configuration changes.
|
To force the router to switch over to the backup or switch back to the primary pseudowire, use the l2vpn switchover command in .EXEC mode
A manual switchover is made only if the peer specified in the command is actually available and the cross-connect moves to the fully active state when the command is entered.
Perform this task to configure a backup pseudowire for a point-to-point neighbor.
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
|
Step 2 |
l2vpn Example:Enters L2VPN configuration mode. |
|
Step 3 |
xconnect group group-name Example:Enters the name of the cross-connect group. |
|
Step 4 |
p2p xconnect-name Example:Enters a name for the point-to-point cross-connect. |
|
Step 5 |
neighbor ip-address pw-id value Example:Configures the pseudowire segment for the cross-connect. |
|
Step 6 |
neighbor { A.B.C.D } { pw-id value } Example:Configures the backup pseudowire for the cross-connect. |
|
Step 7 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
Perform this task to configure point-to-point pseudowire redundancy for a backup delay.
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
|
Step 2 |
l2vpn Example:Enters L2VPN configuration mode. |
|
Step 3 |
pw-class { class-name } Example:Configures the pseudowire class name. |
|
Step 4 |
backup disable { delay value | never } Example:This command specifies how long the primary pseudowire should wait after it becomes active to take over for the backup pseudowire.
|
|
Step 5 |
exit Example:Exits the current configuration mode. |
|
Step 6 |
xconnect group group-name Example:Enters the name of the cross-connect group. |
|
Step 7 |
p2p { xconnect-name } Example:Enters a name for the point-to-point cross-connect. |
|
Step 8 |
neighbor { A.B.C.D } { pw-id value } Example:Configures the pseudowire segment for the cross-connect. |
|
Step 9 |
pw-class { class-name } Example:Configures the pseudowire class name. |
|
Step 10 |
backup { neighbor A.B.C.D } { pw-id value } Example:Configures the backup pseudowire for the cross-connect.
|
|
Step 11 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
To force the router to switch over to the backup or primary pseudowire, use the l2vpn switchover command in EXEC mode.
A manual switchover is made only if the peer specified in the command is actually available and the cross-connect moves to the fully active state when the command is entered.
Note |
The tunnel used for the preferred path configuration is an MPLS Traffic Engineering (MPLS-TE) tunnel. |
|
Step 1 |
configure Example:Enters the configuration mode. |
|
Step 2 |
l2vpn Example:Enters L2VPN configuration mode. |
|
Step 3 |
pw-class {name } Example:Configures the pseudowire class name. |
|
Step 4 |
encapsulation mpls Example:Configures the pseudowire encapsulation to MPLS. |
|
Step 5 |
preferred-path {interface } {tunnel-ip value | tunnel-te value | tunnel-tp value } [fallback disable ] Example:Configures preferred path tunnel settings. If the fallback disable configuration is used and once the TE/TP tunnel is configured as the preferred path goes down, the corresponding pseudowire can also go down. |
|
Step 6 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
Perform this task to configure pseudowire status OAM.
|
Step 1 |
configure Example:Enters the configuration mode. |
||
|
Step 2 |
l2vpn Example:Enters L2VPN configuration mode. |
||
|
Step 3 |
pw-oam refresh transmit seconds Example:Enables pseudowire OAM functionality..
|
||
|
Step 4 |
endorcommit Example:or Saves configuration changes.
|
Perform this task to enable flow-based load balancing.
|
Step 1 |
configure Example:Enters the configuration mode. |
|
Step 2 |
l2vpn Example:Enters L2VPN configuration mode. |
|
Step 3 |
load-balancing flow {src-dst-mac | src-dst-ip} Example:Enables flow based load balancing for all the pseudowires and bundle EFPs under L2VPN, unless otherwise explicitly specified for pseudowires via pseudowire class and bundles via EFP-hash. |
|
Step 4 |
endorcommit Example:or Saves configuration changes.
|
Perform this task to enable flow-based load balancing for a pseudowire class.
|
Step 1 |
configure Example:Enters the configuration mode. |
|
Step 2 |
l2vpn Example:Enters L2VPN configuration mode. |
|
Step 3 |
pw-class {name} Example:Configures the pseudowire class name. |
|
Step 4 |
encapsulation mpls Example:Configures the pseudowire encapsulation to MPLS. |
|
Step 5 |
load-balancing pw-label Example:Enables all pseudowires using the defined class to use virtual circuit based load balancing. |
|
Step 6 |
endorcommit Example:or Saves configuration changes.
|
Perform this task to enable pseudowire grouping.
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
|
Step 2 |
l2vpn Example:Enters L2VPN configuration mode. |
|
Step 3 |
pw-grouping Example:Enables pseudowire grouping |
|
Step 4 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
Refer to the Implementing Multicast Routing on Cisco ASR 9000 Series Aggregation Services Routers module of the Cisco ASR 9000 Series Aggregation Services Router Multicast Configuration Guide and the Multicast Routing and Forwarding Commands on Cisco ASR 9000 Series Aggregation Services Routers module of the Cisco ASR 9000 Series Aggregation Services Router Multicast Command Reference.
|
Step 1 |
configure Example:Enters global configuration mode. |
||
|
Step 2 |
multicast-routing [address-family ipv4] Example:Enters multicast routing configuration mode.
|
||
|
Step 3 |
interface all enable Example:Enables multicast routing and forwarding on all new and existing interfaces. |
||
|
Step 4 |
exit Example:Exits multicast routing configuration mode, and returns the router to the parent configuration mode.
|
||
|
Step 5 |
router igmp Example:(Optional) Enters router IGMP configuration mode. |
||
|
Step 6 |
version {1 | 2 | 3} Example:(Optional) Selects the IGMP version that the router interface uses.
|
||
|
Step 7 |
endorcommit Example:or Saves configuration changes.
|
||
|
Step 8 |
show pim [ipv4] group-map [ip-address-name] [info-source] Example:(Optional) Displays group-to-PIM mode mapping. |
||
|
Step 9 |
show pim [vrf vrf-name] [ipv4] topology [source-ip-address [group-ip-address] | entry-flag flag | interface-flag | summary] [route-count] Example:(Optional) Displays PIM topology table information for a specific group or all groups. |
Perform this task to configure AToM IP Interworking.
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
|
Step 2 |
l2vpn Example:Enters L2VPN configuration mode. |
|
Step 3 |
xconnect groupgroup-name Example:Enters the name of the cross-connect group. |
|
Step 4 |
p2pxconnect-name Example:Enters a name for the point-to-point cross-connect. |
|
Step 5 |
interworking ipv4 Example:Configures IPv4 interworking under P2P. |
|
Step 6 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
Perform this tasks to configure PPP IP Interworking:
|
Step 1 |
configure Example:Enters global configuration mode. |
||
|
Step 2 |
interface type interface-path-id Example:Specifies the interface type and instance. |
||
|
Step 3 |
encapsulation ppp Example:Sets encapsulation type to PPP. |
||
|
Step 4 |
l2transport Example:Enables Layer 2 transport on the selected interface. |
||
|
Step 5 |
end Example:Returns to global configuration mode. |
||
|
Step 6 |
l2vpn Example:Enters L2VPN configuration mode. |
||
|
Step 7 |
xconnect group group-name Example:Enters the name of the cross-connect group. |
||
|
Step 8 |
p2p xconnect-name Example:Enters a name for the point-to-point cross-connect. |
||
|
Step 9 |
interface type interface-path-id Example:Specifies the interface type and instance. |
||
|
Step 10 |
interface type interface-path-id Example:Specifies the interface type and instance. |
||
|
Step 11 |
interworking ipv4 Example:Configures IPv4 interworking under P2P. |
||
|
Step 12 |
interface type interface-path-id Example:Specifies the interface type and instance. |
||
|
Step 13 |
neighborA.B.C.Dpw-id Example:Configures the pseudowire segment for the cross-connect. Use the A.B.C.D argument to specify the IP address of the cross-connect peer.
Optionally, you can disable the control word or set the transport-type to Ethernet or VLAN |
||
|
Step 14 |
pw-class interface-path-id Example:Enters pseudowire class submode, allowing you to define a pseudowire class template. |
||
|
Step 15 |
exit Example:Exits the current configuration mode. |
||
|
Step 16 |
interworking ipv4 Example:Configures IPv4 interworking under P2P. |
||
|
Step 17 |
endorcommit Example:or Saves configuration changes.
|
Perform this tasks to configure PPP IP Interworking:
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
||
|
Step 2 |
interface typeinterface-path-id Example:Specifies the interface type and instance. |
||
|
Step 3 |
l2transport Example:Enables Layer 2 transport on the selected interface. |
||
|
Step 4 |
end Example:Returns to global configuration mode. |
||
|
Step 5 |
l2vpn Example:Enters L2VPN configuration mode. |
||
|
Step 6 |
xconnect groupgroup-name Example:Enters the name of the cross-connect group. |
||
|
Step 7 |
p2pxconnect-name Example:Enters a name for the point-to-point cross-connect. |
||
|
Step 8 |
interface typeinterface-path-id Example:Specifies the interface type and instance. |
||
|
Step 9 |
interface type interface-path-id Example:Specifies the interface type and instance. |
||
|
Step 10 |
interworking ipv4 Example:Configures IPv4 interworking under P2P. |
||
|
Step 11 |
interface type interface-path-id Example:Specifies the interface type and instance. |
||
|
Step 12 |
neighborA.B.C.Dpw-id Example:Configures the pseudowire segment for the cross-connect. Use the A.B.C.D argument to specify the IP address of the cross-connect peer.
Optionally, you can disable the control word or set the transport-type to Ethernet or VLAN |
||
|
Step 13 |
pw-classclass-name Example:Configures the pseudowire segment for the cross-connect. Use the A.B.C.D argument to specify the IP address of the cross-connect peer.
Optionally, you can disable the control word or set the transport-type to Ethernet or VLAN |
||
|
Step 14 |
pw-classclass-name Example:Enters pseudowire class submode, allowing you to define a pseudowire class template. |
||
|
Step 15 |
exit Example:Exits the current configuration mode. |
||
|
Step 16 |
interworking ipv4 Example:Configures IPv4 interworking under P2P. |
||
|
Step 17 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
Perform this tasks to configure cHDLC IP Interworking:
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
||
|
Step 2 |
interface typeinterface-path-id Example:Specifies the interface type and instance. |
||
|
Step 3 |
multilink [fragment|interleave|ncp] Example:Modifies multilink parameters |
||
|
Step 4 |
l2transport Example:Enables Layer 2 transport on the selected interface. |
||
|
Step 5 |
end Example:Returns to global configuration mode. |
||
|
Step 6 |
l2vpn Example:Enters L2VPN configuration mode. |
||
|
Step 7 |
xconnect group group-name Example:Enters the name of the cross-connect group. |
||
|
Step 8 |
p2p xconnect-name Example:Enters a name for the point-to-point cross-connect. |
||
|
Step 9 |
interface typeinterface-path-id Example:Specifies the interface type and instance. |
||
|
Step 10 |
interface typeinterface-path-id Example:Specifies the interface type and instance. |
||
|
Step 11 |
interworking ipv4 Example:Configures IPv4 interworking under P2P. |
||
|
Step 12 |
interface typeinterface-path-id Example:Specifies the interface type and instance. |
||
|
Step 13 |
neighbor{A.B.C.D}{pw-idvalue} Example:Configures the pseudowire segment for the cross-connect. Use the A.B.C.D argument to specify the IP address of the cross-connect peer.
Optionally, you can disable the control word or set the transport-type to Ethernet or VLAN |
||
|
Step 14 |
pw-classclass-name Example:Enters pseudowire class submode, allowing you to define a pseudowire class template. |
||
|
Step 15 |
exit Example:Exits the current configuration mode. |
||
|
Step 16 |
interworking ipv4 Example:Configures IPv4 interworking under P2P. |
||
|
Step 17 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
Perform these tasks to configure CEoP:
Perform this task to add a CEM attachment circuit to a pseudowire.:
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
||
|
Step 2 |
l2vpn Example:Enters L2VPN configuration mode. |
||
|
Step 3 |
xconnect group group-name Example:Enters the name of the cross-connect group. |
||
|
Step 4 |
p2p xconnect-name Example:Enters a name for the point-to-point cross-connect. |
||
|
Step 5 |
interface type interface-path-id Example:Specifies the interface type and instance. |
||
|
Step 6 |
neighbor A.B.C.D pw-id Example:Configures the pseudowire segment for the cross-connect. Use the A.B.C.D argument to specify the IP address of the cross-connect peer.
Optionally, you can disable the control word or set the transport-type to Ethernet or VLAN |
||
|
Step 7 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
Perform this task to associate the attachment circuit with a pseudowire class.
|
Step 1 |
configure Example:Enters Global Configuration mode. |
||||
|
Step 2 |
l2vpn Example:Enters Layer 2 VPN configuration mode. |
||||
|
Step 3 |
pw-class class-name Example:Enters pseudowire class submode, allowing you to define a pseudowire class template. |
||||
|
Step 4 |
encapsulation mpls Example:Sets pseudowire encapsulation to MPLS. |
||||
|
Step 5 |
protocol ldp Example:Sets pseudowire signaling protocol to LDP. |
||||
|
Step 6 |
end Example:System prompts you to commit changes:
|
||||
|
Step 7 |
xconnect group group-name Example:Configures a cross-connect group. |
||||
|
Step 8 |
p2p xconnect-name Example:Configures a point-to-point cross-connect. |
||||
|
Step 9 |
interface type interface-path-id Example:Specifies the interface type and instance. |
||||
|
Step 10 |
neighbor A.B.C.D pw-id pseudowire-id Example:Configures the pseudowire segment for the cross-connect. Use the A.B.C.D argument to specify the IP address of the cross-connect peer.
Optionally, you can disable the control word or set the transport-type to Ethernet or VLAN.
|
||||
|
Step 11 |
pw-class class-name Example:Associates the P2P attachment circuit with the specified pseudowire class. |
||||
|
Step 12 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
Perform this task to enable pseudowire status.
|
Step 1 |
configure Example:Enters global configuration mode. |
||
|
Step 2 |
l2vpn Example:Enters Layer 2 VPN configuration mode. |
||
|
Step 3 |
pw-status Example:
|
||
|
Step 4 |
commit Example:Saves configuration changes to the running configuration file and remains in the configuration session. |
Perform this task to configure a backup pseudowire for a point-to-point neighbor.
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
|
Step 2 |
l2vpn Example:Enters L2VPN configuration mode. |
|
Step 3 |
xconnect group group-name Example:Enters the name of the cross-connect group. |
|
Step 4 |
p2p xconnect-name Example:Enters a name for the point-to-point cross-connect. |
|
Step 5 |
neighbor ip-address pw-id value Example:Configures the pseudowire segment for the cross-connect. |
|
Step 6 |
neighbor { A.B.C.D } { pw-id value } Example:Configures the backup pseudowire for the cross-connect. |
|
Step 7 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
Perform this task to configure L2VPN Nonstop Routing.
|
Step 1 |
configure Example:Enters Global Configuration mode. |
|
Step 2 |
l2vpn Example:Enters the Global Configuration mode. |
|
Step 3 |
nsr Example:Enables L2VPN nonstop routing. |
|
Step 4 |
logging nsr Example:Enables logging of NSR events. |
|
Step 5 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
Perform this task to enable Label Distribution Protocol (LDP) Nonstop Routing (NSR) for synchronizing label information between active and standby LDPs. From Release 6.1.1 onwards, with the introduction of stateful LDP feature, you must explicitly configure LDP NSR to synchronize label information between active and standby LDPs.
|
Step 1 |
configure Example:Enters Global Configuration mode. |
|
Step 2 |
mpls ldp Example:Enters MPLS LDP configuration mode. |
|
Step 3 |
nsr Example:Enables LDP nonstop routing. |
|
Step 4 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
Perform these tasks to configure the L2TPv3 over IPv6 tunnels:
Perform this task to configure the neighbor AFI for pseudowire.
Restriction |
L2TPv3 over IPv6Tunnels is supported only on layer 2 transport sub-interfaces and not physical interfaces. |
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
|
Step 2 |
l2vpn Example:Enters Layer 2 VPN configuration mode. |
|
Step 3 |
xconnect group group-name Example:Configures a cross-connect group and specifies it’s name. |
|
Step 4 |
p2p xconnect-name Example:Configures a point-to-point cross-connect. |
|
Step 5 |
interface type interface-path-id Example:Specifies the interface type ID. The choices are:
|
|
Step 6 |
neighbor ipv6 X:X::X pw-idpseudowire-id Example:Specifies the peer with which to cross connect, and configures the pseudowire segment for the cross-connect. |
|
Step 7 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
Perform this task to configure L2TPv3 encapsulation and protocol.
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
|
Step 2 |
l2vpn Example:Enters Layer 2 VPN configuration mode. |
|
Step 3 |
pw-class class-name Example:Enters pseudowire class submode, allows a pseudowire class template definition. These keywords can be configured in the pseudowire class (pw-class) configuration mode; however, the keywords are not applicable for the over L2TPv3 over IPv6 tunnels:
|
|
Step 4 |
encapsulation l2tpv3 Example:Sets pseudowire encapsulation to L2TPv3 |
|
Step 5 |
protocol l2tpv3 Example:Sets pseudowire signaling protocol to L2TPv3. |
|
Step 6 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
Perform this task to configure the source IPv6 address for the L2TPv3 over IPv6 tunnel.
|
Step 1 |
configure Example:Enters global configuration mode. |
||
|
Step 2 |
l2vpn Example:Enters Layer 2 VPN configuration mode. |
||
|
Step 3 |
xconnect group group-name Example:Configures the cross-connect group. |
||
|
Step 4 |
p2p xconnect-name Example:Configures the point-to-point cross-connect. |
||
|
Step 5 |
interface type interface-path-id Example:Specifies the interface type ID. |
||
|
Step 6 |
neighbor ipv6 peer-address pw-id pseudowire-id Example:Specifies the peer with which to cross connect, and configures the pseudowire segment for the cross-connect. |
||
|
Step 7 |
source pw-source-address Example:Configures the source IPv6 address of the pseudowire.
|
||
|
Step 8 |
end or commit Example:or Saves configuration changes.
|
Perform this task to configure local and remote sessions.
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
||
|
Step 2 |
l2vpn Example:Enters Layer 2 VPN configuration mode. |
||
|
Step 3 |
xconnect group group-name Example:Configures the cross-connect group. |
||
|
Step 4 |
p2p xconnect-name Example:Configures the point-to-point cross-connect. |
||
|
Step 5 |
interface type interface-path-id Example:Specifies the interface type ID. |
||
|
Step 6 |
neighbor ipv6 peer-address pw-id pseudowire-id Example:Specifies the peer with which to cross connect, and configures the pseudowire segment for the cross-connect. |
||
|
Step 7 |
l2tp static local session session-id Example:(Optional) Configures a static local session for the L2TP pseudowire.
|
||
|
Step 8 |
l2tp static remote session session-id Example:(Optional) Configures a static remote session for the L2TP pseudowire.
|
||
|
Step 9 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
Perform this task to configure local and remote cookies.
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
||
|
Step 2 |
l2vpn Example:Enters Layer 2 VPN configuration mode. |
||
|
Step 3 |
xconnect group group-name Example:Configures the cross-connect group. |
||
|
Step 4 |
p2p xconnect-name Example:Configures the point-to-point cross-connect. |
||
|
Step 5 |
interface type interface-path-id Example:Specifies the interface type ID. |
||
|
Step 6 |
neighbor ipv6 peer-address pw-id pseudowire-id Example:Specifies the peer with which to cross connect, and configures the pseudowire segment for the cross-connect. |
||
|
Step 7 |
l2tp static local cookie size bytes Example:Configures the static local cookie size settings for the L2TP pseudowire.
|
||
|
Step 8 |
l2tp static local cookie size bytes Example:Configures the static remote cookie size settings for the L2TP pseudowire.
|
||
|
Step 9 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
Perform this task to enable L2TP static submode.
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
|
Step 2 |
l2vpn Example:Enters Layer 2 VPN configuration mode. |
|
Step 3 |
xconnect group group-name Example:Configures the cross-connect group. |
|
Step 4 |
p2p xconnect-name Example:Configures the point-to-point cross-connect. |
|
Step 5 |
interface type interface-path-id Example:Specifies the interface type ID. |
|
Step 6 |
neighbor ipv6 peer-address pw-id pseudowire-id Example:Specifies the peer with which to cross connect, and configures the pseudowire segment for the cross-connect. |
|
Step 7 |
l2tp static Example:Enters L2TP static configuration submode. |
|
Step 8 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
Perform this task to enable the type of service (TOS) reflection in the L2TPv3 header.
|
Step 1 |
configure Example:Enters global configuration mode. |
|
Step 2 |
l2vpn Example:Enters Layer 2 VPN configuration mode. |
|
Step 3 |
pw-classclass-name Example:Enters pseudowire class submode, and allows a pseudowire class template definition. |
|
Step 4 |
encapsulation l2tpv3 Example:Sets pseudowire encapsulation to L2TPv3. |
|
Step 5 |
protocol l2tpv3 Example:Sets pseudowire signaling protocol to L2TPv3. |
|
Step 6 |
neighbor ipv6peer-address pw-id pseudowire-id Example:Specifies the peer with which to cross connect, and configures the pseudowire segment for the cross-connect. |
|
Step 7 |
tos { reflect | value } Example:Enables type of service (TOS) reflection. As a result, copies TOS from inner IP header to the L2TPv3 header. Additionally, use this command to set the value of TOS for the L2TPv3 pseudowire class. The range is from 0 to 255. |
|
Step 8 |
endorcommit Example:or Saves configuration changes.
|
Perform this task to configure time to live (TTL) for L2TPv3 over IPv6 tunnels.
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
|
Step 2 |
l2vpn Example:Enters Layer 2 VPN configuration mode. |
|
Step 3 |
pw-class class-name Example:Enters pseudowire class submode, and allows a pseudowire class template definition. |
|
Step 4 |
encapsulation l2tpv3 Example:Sets pseudowire encapsulation to L2TPv3. |
|
Step 5 |
protocol l2tpv3 Example:Sets pseudowire signaling protocol to L2TPv3. |
|
Step 6 |
ttl value Example:Sets time to live (TTL), in node hops, to a specified value. The range is from 1 to 255. |
|
Step 7 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
Perform this task to configure traffic mirroring over L2TPv3 over IPv6 tunnels.
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
|
Step 2 |
l2vpn Example:Enters Layer 2 VPN configuration mode. |
|
Step 3 |
xconnect groupgroup-name Example:Configures the cross-connect group. |
|
Step 4 |
p2p xconnect-name Example:Configures the point-to-point cross-connect. |
|
Step 5 |
monitor-session session-name Example:Specifies the monitor session. |
|
Step 6 |
neighbor ipv6 peer-address pw-id pseudowire-id Example:Specifies the peer with which to cross connect, and configures the pseudowire segment for the cross-connect. |
|
Step 7 |
pw-class class-name Example:Enters pseudowire class submode, and allows a pseudowire class template definition. |
|
Step 8 |
sourcepw-source-address Example:Configures the source IPv6 address of the pseudowire. |
|
Step 9 |
l2tp static local cookie sizesizevaluebytes Example:Configures the static local cookie size settings for the L2TP pseudowire. |
|
Step 10 |
l2tp static remote cookie sizesizevaluebytes Example:Configures the static remote cookie size settings for the L2TP pseudowire. |
|
Step 11 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
For more information on:
|
Restriction |
L2TPv3 over Ipv4 Tunnels is supported only on layer 2 transport sub-interfaces and not on physical interfaces. When an untagged traffic has to be sent through L2TPv3 over IPv4, create a sub-interface with encapsulation as untagged. |
Perform these tasks to configure the L2TPv3 over IPv4 tunnels:
Perform this task to configure a dynamic L2TPv3 pseudowire connecting to a remote IPv4 peer.
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
|
Step 2 |
l2vpn Example:Enter L2VPN configure submode. |
|
Step 3 |
xconnect group name Example:Enter a name for the cross-connect group. |
|
Step 4 |
p2p name Example:Enters p2p configuration submode to configure point-to-point cross-connects. |
|
Step 5 |
interface type interface-path-id Example:Specifies the interface type ID. The choices are:
|
|
Step 6 |
neighbor ipv4 ip-address pw-id number Example:Configures a pseudowire for a cross-connect. |
|
Step 7 |
pw-class pw-class-name Example:Enters pseudowire class submode to define a name for the cross-connect. |
|
Step 8 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
Perform this task to configure L2TPv3 encapsulation and protocol.
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
|
Step 2 |
l2vpn Example:Enters Layer 2 VPN configuration mode. |
|
Step 3 |
pw-class class-name Example:Enters pseudowire class submode, allows a pseudowire class template definition. These keywords can be configured in the pseudowire class (pw-class) configuration mode:
|
|
Step 4 |
encapsulation l2tpv3 Example:Sets pseudowire encapsulation to L2TPv3 |
|
Step 5 |
protocol l2tpv3 Example:Sets pseudowire signaling protocol to L2TPv3. |
|
Step 6 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
L2TP control-channel parameters are used in control-channel authentication, keepalive messages, and control-channel negotiation. In a L2tpv3 session, the same L2TP class must be configured on both PE routers.
The following L2TP control-channel parameters can be configured in L2TP class configuration mode:
Authentication for the L2TP control-channel
Password used for L2TP control-channel authentication
Retransmission parameters used for control messages.
Timeout parameters used for the control-channel.
Maintenance Parameters
L2TPv3 Control Message Hashing
Perform this task to create a template of L2TP control-channel parameters that can be inherited by different pseudowire classes.
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
||
|
Step 2 |
l2tp-class l2tp-class-name Example:Specifies the L2TP class name and enters L2TP class configuration mode. |
||
|
Step 3 |
authentication Example:Enables authentication for the control-channel between PE routers. |
||
|
Step 4 |
password {0 | 7} password Example:Configures the password used for control-channel authentication.
|
||
|
Step 5 |
retransmit { initial retries initial-retries | retries retries | timeout { max | min } timeout } Example:Configures parameters that affect the retransmission of control packets.
|
||
|
Step 6 |
hello-interval interval Example:Specifies the exchange interval (in seconds) used between L2TP hello packets.
|
||
|
Step 7 |
digest { check disable | hash { MD5 | SHA1 } ] | secret { 0 | 7 } password ] Example:Enables L2TPv3 control-channel authentication or integrity checking.
|
||
|
Step 8 |
hidden Example:Enables AVP hiding when sending control messages to an L2TPv3 peer. |
To configure single segment pseudowire in the network, do the following:
(Optional) Configuring the related L2VPN Global Parameters. See Configuring L2VPN Global Parameters
This procedure is used to overwrite the default BGP Route Distinguisher (RD) auto-generated value and also the Autonomous System Number (ASN) and Route Identifier (RID) of BGP.
Configuring L2VPN MS-PW Address Family Under BGP
The address family is configured under BGP to exchange the dynamic pseudowire routes.
Perform this task to configure L2VPN global parameters.
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
|
Step 2 |
l2vpn Example:Enters Layer 2 VPN configuration mode. |
|
Step 3 |
router-id router-id Example:Specifies the router ID. |
|
Step 4 |
pw-routing Example:Enables pseudowire routing capabilities and enters the pseudowire routing configuration submode |
|
Step 5 |
global-id global-id Example:Configures the L2VPN global ID value for the router. |
|
Step 6 |
bgp Example:Enables the BGP pseudowire routing capabilities and enters the BGP configuration submode. |
|
Step 7 |
rd route-distinguisher Example:Configures the BGP route distinguisher. |
|
Step 8 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
Perform this task to configure L2VPN VPWS SS-PWs.
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
|
Step 2 |
interface typeinterface-path-id Example:Enters interface configuration mode and configures an interface. |
|
Step 3 |
l2vpn Example:Enters Layer 2 VPN configuration mode. |
|
Step 4 |
xconnect group group-name Example:Configures a cross-connect group name using a free-format 32-character string. |
|
Step 5 |
p2p xconnect-name Example:Enters P2P configuration submode. |
|
Step 6 |
interface type interface-path-id Example:Specifies the interface type and instance. |
|
Step 7 |
neighbor routed global-id: prefix: ac-id source ac-id Example:Enables pseudowire routing configuration submode for the p2p cross-connect. |
|
Step 8 |
(optional) pw-class class-name Example:Enters pseudowire class submode, allowing you to define a pseudowire class template. |
|
Step 9 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
Perform this task to configure L2VPN MS-PW address family under BGP:
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
|
Step 2 |
router bgp autonomous-system-number Example:Enters router configuration mode for the specified routing process. |
|
Step 3 |
address-family l2vpn mspw Example:Specifies the L2VPN address family and enters address family configuration mode. |
|
Step 4 |
neighbor ip-address Example:Adds the IP address of the neighbor in the specified autonomous system. |
|
Step 5 |
address-family l2vpn mspw Example:Specifies the L2VPN address family of the neighbor and enters address family configuration mode. |
|
Step 6 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
To verify the connectivity in SS-PWs, use the ping mpls pseudowire command.
The show commands are used to display information about L2VPN Single Segment Pseudowires
The following steps are performed to configure EVPN-VPWS:
Perform this task to configure L2VPN EVPN address family under BGP:
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
|
Step 2 |
router bgp autonomous-system-number Example:Enters router configuration mode for the specified routing process. |
|
Step 3 |
address-family l2vpn evpn Example:Specifies the L2VPN address family and enters address family configuration mode. |
|
Step 4 |
neighbor ip-address Example:Adds the IP address of the neighbor in the specified autonomous system. |
|
Step 5 |
address-family l2vpn evpn Example:Specifies the L2VPN address family of the neighbor and enters address family configuration mode. |
|
Step 6 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
Perform this task to configure EVPN-VPWS.
Note |
You can configure the PWHE interface as well, using EVPN-VPWS. Refer to the Configuring Pseudowire Headend module for more information. |
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
|
Step 2 |
interface type interface-path-id Example:Enters interface configuration mode and configures an interface. |
|
Step 3 |
l2vpn Example:Enters Layer 2 VPN configuration mode. |
|
Step 4 |
xconnect group group-name Example:Configures a cross-connect group name using a free-format 32-character string. |
|
Step 5 |
p2p xconnect-name Example:Enters P2P configuration submode. |
|
Step 6 |
interface type interface-path-id Example:Specifies the interface type and instance. |
|
Step 7 |
neighbor evpn evi vpn-idtarget ac-id Example:Enables EVPN-VPWS endpoint on the p2p cross-connect. |
|
Step 8 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
Bridge-domain can configure an access pseudowire using EVPN-VPWS:
| Command or Action | Purpose | |
|---|---|---|
|
Step 1 |
configure Example: |
Enters the Global Configuration mode. |
|
Step 2 |
interface type interface-path-id Example: |
Enters interface configuration mode and configures an interface. |
|
Step 3 |
l2vpn Example: |
Enters Layer 2 VPN configuration mode. |
|
Step 4 |
bridge group bridge-group-name Example: |
Creates a bridge group that can contain bridge domains, and then assigns network interfaces to the bridge domain. |
|
Step 5 |
bridge-domain bridge-domain-name Example: |
Establishes a bridge domain and enters L2VPN bridge group bridge domain configuration mode. |
|
Step 6 |
neighbor evpn evi vpn-id target ac-id Example: |
Enables EVPN-VPWS endpoint on the p2p cross-connect. |
This section includes these configuration examples:
The following example shows how to configure an L2VPN interface :
configure
interface GigabitEthernet0/0/0/0.1 l2transport
encapsulation dot1q 1
rewrite ingress tag pop 1 symmetric
endThis example shows how to configure Layer 2 local switching:
configure
l2vpn
xconnect group examples
p2p example1
interface TenGigE0/7/0/6.5
interface GigabitEthernet0/4/0/30
commit
end
show l2vpn xconnect group examples
Legend: ST = State, UP = Up, DN = Down, AD = Admin Down, UR = Unresolved,
SB = Standby, SR = Standby Ready
XConnect Segment 1 Segment 2
Group Name ST Description ST Description ST
examples example1 UP Te0/7/0/6.5 UP Gi0/4/0/30 UPThe following example shows how to configure the LCR on PoA1:
! LCR - CE1
group 107
mlacp node 1
mlacp system mac 0001.0001.0107
mlacp system priority 107
member
neighbor 200.0.2.1
!
! LCR - CE2
group 207
mlacp node 1
mlacp system mac 0001.0001.0207
mlacp system priority 207
member
neighbor 200.0.2.1
!
interface Bundle-Ether107
description CE5 - LCR
mlacp iccp-group 107
mlacp port-priority 10
no shut
interface Bundle-Ether207
description CE6 - LCR
mlacp iccp-group 207
mlacp port-priority 10
no shut
interface bundle-e107.1 l2t
description CE5 - LCR
encap dot1q 107 second 1
rewrite ingress tag pop 2 symmetric
interface bundle-e207.1 l2t
description CE2 - LCR
encap dot1q 207 second 1
rewrite ingress tag pop 2 symmetric
interface bundle-e307.1 l2t
description PE2 - LCR
encap dot1q 1
rewrite ingress tag pop 1 symmetric
l2vpn
xconnect group lcr-scale
p2p lcr-1
interface bundle-e107.1
interface bundle-e207.1
backup interface bundle-e307.1
This section includes configuration examples for both static and dynamic p2p cross-connects.
This example shows how to configure a static point-to-point cross-connect:
configure
l2vpn
xconnect group vlan_grp_1
p2p vlan1
interface GigabitEthernet0/0/0/0.1
neighbor 102.2.12.1 2 pw-id 1
mpls static label local 699 remote 890
commit2000This example shows how to configure a dynamic point-to-point cross-connect:
configure
l2vpn
xconnect group vlan_grp_1
p2p vlan1
interface TenGigE 0/0/0/0.1
neighbor 2.2.1.1 pw-id 1
commitThis example shows how to set up an AC to AC cross-connect from AC1 to AC2:
router-id Loopback0
interface Loopback0
ipv4 address 10.0.0.5 255.255.255.255
!
interface GigabitEthernet0/1/0/0.1 l2transport
encapsulation dot1q 1
!
!
interface GigabitEthernet0/0/0/3
ipv4 address 10.45.0.5 255.255.255.0
keepalive disable
!
interface GigabitEthernet0/0/0/4
ipv4 address 10.5.0.5 255.255.255.0
keepalive disable
!
router ospf 100
log adjacency changes detail
area 0
interface Loopback0
!
interface GigabitEthernet0/0/0/3
!
interface GigabitEthernet0/0/0/4
!
!
!
router bgp 100
address-family ipv4 unicast
allocate-label all
!
neighbor 10.2.0.5
remote-as 100
update-source Loopback0
address-family ipv4 unicast
!
address-family ipv4 labeled-unicast
!
!
!
l2vpn
xconnect group cisco
p2p cisco1
interface GigabitEthernet0/1/0/0.1
neighbor 10.0.1.5 pw-id 101
!
p2p cisco2
interface GigabitEthernet0/1/0/0.2
neighbor 10.0.1.5 pw-id 102
!
p2p cisco3
interface GigabitEthernet0/1/0/0.3
neighbor 10.0.1.5 pw-id 103
!
p2p cisco4
interface GigabitEthernet0/1/0/0.4
neighbor 10.0.1.5 pw-id 104
!
p2p cisco5
interface GigabitEthernet0/1/0/0.5
neighbor 10.0.1.5 pw-id 105
!
p2p cisco6
interface GigabitEthernet0/1/0/0.6
neighbor 10.0.1.5 pw-id 106
!
p2p cisco7
interface GigabitEthernet0/1/0/0.7
neighbor 10.0.1.5 pw-id 107
!
p2p cisco8
interface GigabitEthernet0/1/0/0.8
neighbor 10.0.1.5 pw-id 108
!
p2p cisco9
interface GigabitEthernet0/1/0/0.9
neighbor 10.0.1.5 pw-id 109
!
p2p cisco10
interface GigabitEthernet0/1/0/0.10
neighbor 10.0.1.5 pw-id 110
!
!
!
mpls ldp
router-id Loopback0
log
neighbor
!
interface GigabitEthernet0/0/0/3
!
interface GigabitEthernet0/0/0/4
!
!
end
This example shows how to attach a service-policy to an L2 interface in port mode:
configure
interface GigabitEthernet 0/0/0/0
l2transport
service-policy input pmap_1
commitThe examples include these devices and connections:
T-PE1 node has:
T-PE2 node
S-PE1 node
RP/0/RSP0/CPU0:T-PE1# configure
RP/0/RSP0/CPU0:T-PE1(config)# l2vpn
RP/0/RSP0/CPU0:T-PE1 (config-l2vpn)# pw-class dynamic_mpls
RP/0/RSP0/CPU0:T-PE1(config-l2vpn-pwc)# encapsulation mpls
RP/0/RSP0/CPU0:T-PE1(config-l2vpn-pwc-encap-mpls)# protocol ldp
RP/0/RSP0/CPU0:T-PE1(config-l2vpn-pwc-encap-mpls)# control-word disable
RP/0/RSP0/CPU0:T-PE1(config-l2vpn-pwc-encap-mpls)# exit
RP/0/RSP0/CPU0:T-PE1(config-l2vpn-pwc)# exit
RP/0/RSP0/CPU0:T-PE1(config-l2vpn)# xconnect group XCON1
RP/0/RSP0/CPU0:T-PE1(config-l2vpn-xc)# p2p xc1
RP/0/RSP0/CPU0:T-PE1(config-l2vpn-xc-p2p)# description T-PE1 MS-PW to 10.165.202.158 via 10.165.200.254
RP/0/RSP0/CPU0:T-PE1(config-l2vpn-xc-p2p)# interface gigabitethernet 0/1/0/0.1
RP/0/RSP0/CPU0:T-PE1(config-l2vpn-xc-p2p)# neighbor 10.165.200.254 pw-id 100
RP/0/RSP0/CPU0:T-PE1(config-l2vpn-xc-p2p-pw)# pw-class dynamic_mpls
RP/0/RSP0/CPU0:T-PE1(config-l2vpn-xc-p2p-pw)# commitRP/0/RSP0/CPU0:S-PE1# configure
RP/0/RSP0/CPU0:S-PE1(config)# l2vpn
RP/0/RSP0/CPU0:S-PE1(config-l2vpn)# pw-class dynamic_mpls
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-pwc)# encapsulation mpls
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-pwc-encap-mpls)# protocol ldp
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-pwc-encap-mpls)# control-word disable
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-pwc-encap-mpls)# exit
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-pwc)# exit
RP/0/RSP0/CPU0:S-PE1(config-l2vpn)# xconnect group MS-PW1
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-xc)# p2p ms-pw1
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-xc-p2p)# description S-PE1 MS-PW between 10.165.200.225 and 10.165.202.158
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-xc-p2p)# neighbor 10.165.200.225 pw-id 100
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-xc-p2p-pw)# pw-class dynamic_mpls
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-xc-p2p-pw)# exit
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-xc-p2p)# neighbor 10.165.202.158 pw-id 300
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-xc-p2p-pw)# pw-class dynamic_mpls
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-xc-p2p-pw)# commitRP/0/RSP0/CPU0:T-PE2# configure
RP/0/RSP0/CPU0:T-PE2(config)# l2vpn
RP/0/RSP0/CPU0:T-PE2 (config-l2vpn)# pw-class dynamic_mpls
RP/0/RSP0/CPU0:T-PE2 (config-l2vpn-pwc)# encapsulation mpls
RP/0/RSP0/CPU0:T-PE2 (config-l2vpn-pwc-encap-mpls)# protocol ldp
RP/0/RSP0/CPU0:T-PE2 (config-l2vpn-pwc-encap-mpls)# control-word disable
RP/0/RSP0/CPU0:T-PE2 (config-l2vpn-pwc-encap-mpls)# exit
RP/0/RSP0/CPU0:T-PE2 (config-l2vpn-pwc)# exit
RP/0/RSP0/CPU0:T-PE2(config-l2vpn)# xconnect group XCON1
RP/0/RSP0/CPU0:T-PE2(config-l2vpn-xc)# p2p xc1
RP/0/RSP0/CPU0:T-PE2(config-l2vpn-xc-p2p)# description T-PE2 MS-PW to 10.165.200.225 via 10.165.200.254
RP/0/RSP0/CPU0:T-PE2(config-l2vpn-xc-p2p)# interface gigabitethernet 0/2/0/0.4
RP/0/RSP0/CPU0:T-PE2(config-l2vpn-xc-p2p)# neighbor 10.165.200.254 pw-id 300
RP/0/RSP0/CPU0:T-PE2(config-l2vpn-xc-p2p-pw)# pw-class dynamic_mpls
RP/0/RSP0/CPU0:T-PE2(config-l2vpn-xc-p2p-pw)# commitRP/0/RSP0/CPU0:T-PE1# configure
RP/0/RSP0/CPU0:T-PE1(config)# l2vpn
RP/0/RSP0/CPU0:T-PE1(config-l2vpn)# pw-class dynamic_mpls
RP/0/RSP0/CPU0:T-PE1(config-l2vpn-pwc)# encapsulation mpls
RP/0/RSP0/CPU0:T-PE1(config-l2vpn-pwc-encap-mpls)# protocol ldp
RP/0/RSP0/CPU0:T-PE1(config-l2vpn-pwc-encap-mpls)# control-word disable
RP/0/RSP0/CPU0:T-PE1(config-l2vpn-pwc-encap-mpls)# preferred-path interface tunnel-te 1000
RP/0/RSP0/CPU0:T-PE1(config-l2vpn-pwc-encap-mpls)# exit
RP/0/RSP0/CPU0:T-PE1(config-l2vpn-pwc)# exit
RP/0/RSP0/CPU0:T-PE1(config-l2vpn)# xconnect group XCON1
RP/0/RSP0/CPU0:T-PE1(config-l2vpn-xc)# p2p xc1
RP/0/RSP0/CPU0:T-PE1(config-l2vpn-xc-p2p)# description T-PE1 MS-PW to 10.165.202.158 via 10.165.200.254
RP/0/RSP0/CPU0:T-PE1(config-l2vpn-xc-p2p)# interface gigabitethernet 0/1/0/0.1
RP/0/RSP0/CPU0:T-PE1(config-l2vpn-xc-p2p)# neighbor 10.165.200.254 pw-id 100
RP/0/RSP0/CPU0:T-PE1(config-l2vpn-xc-p2p-pw)# pw-class dynamic_mpls
RP/0/RSP0/CPU0:T-PE1(config-l2vpn-xc-p2p-pw)# commitRP/0/RSP0/CPU0:S-PE1# configure
RP/0/RSP0/CPU0:S-PE1(config)# l2vpn
RP/0/RSP0/CPU0:S-PE1(config-l2vpn)# pw-class dynamic_mpls1
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-pwc)# encapsulation mpls
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-pwc-encap-mpls)# protocol ldp
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-pwc-encap-mpls)# control-word disable
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-pwc-encap-mpls)# preferred-path interface tunnel-te 1000
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-pwc-encap-mpls)# exit
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-pwc)# exit
RP/0/RSP0/CPU0:S-PE1(config-l2vpn)# pw-class dynamic_mpls2
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-pwc)# encapsulation mpls
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-pwc-encap-mpls)# protocol ldp
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-pwc-encap-mpls)# control-word disable
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-pwc-encap-mpls)# preferred-path interface tunnel-te 2000
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-pwc-encap-mpls)# exit
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-pwc)# exit
RP/0/RSP0/CPU0:S-PE1(config-l2vpn)# xconnect group MS-PW1
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-xc)# p2p ms-pw1
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-xc-p2p)# description S-PE1 MS-PW between 10.165.200.225 and 10.165.202.158
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-xc-p2p)# neighbor 10.165.200.225 pw-id 100
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-xc-p2p-pw)# pw-class dynamic_mpls1
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-xc-p2p-pw)# exit
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-xc-p2p)# neighbor 10.165.202.158 pw-id 300
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-xc-p2p-pw)# pw-class dynamic_mpls2
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-xc-p2p-pw)# commitRP/0/RSP0/CPU0:T-PE2# configure
RP/0/RSP0/CPU0:T-PE2(config)# l2vpn
RP/0/RSP0/CPU0:T-PE2(config-l2vpn)# pw-class dynamic_mpls
RP/0/RSP0/CPU0:T-PE2(config-l2vpn-pwc)# encapsulation mpls
RP/0/RSP0/CPU0:T-PE2(config-l2vpn-pwc-encap-mpls)# protocol ldp
RP/0/RSP0/CPU0:T-PE2(config-l2vpn-pwc-encap-mpls)# control-word disable
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-pwc-encap-mpls)# preferred-path interface tunnel-te 2000
RP/0/RSP0/CPU0:T-PE2(config-l2vpn-pwc-encap-mpls)# exit
RP/0/RSP0/CPU0:T-PE2(config-l2vpn-pwc)# exit
RP/0/RSP0/CPU0:T-PE2(config-l2vpn)# xconnect group XCON1
RP/0/RSP0/CPU0:T-PE2(config-l2vpn-xc)# p2p xc1
RP/0/RSP0/CPU0:T-PE2(config-l2vpn-xc-p2p)# description T-PE2 MS-PW to 10.165.200.225 via 10.165.200.254
RP/0/RSP0/CPU0:T-PE2(config-l2vpn-xc-p2p)# interface gigabitethernet 0/2/0/0.4
RP/0/RSP0/CPU0:T-PE2(config-l2vpn-xc-p2p)# neighbor 10.165.200.254 pw-id 300
RP/0/RSP0/CPU0:T-PE2(config-l2vpn-xc-p2p-pw)# pw-class dynamic_mpls
RP/0/RSP0/CPU0:T-PE2(config-l2vpn-xc-p2p-pw)# commitRP/0/RSP0/CPU0:T-PE1# configure
RP/0/RSP0/CPU0:T-PE1(config)# l2vpn
RP/0/RSP0/CPU0:T-PE1(config-l2vpn)# xconnect group XCON1
RP/0/RSP0/CPU0:T-PE1(config-l2vpn-xc)# p2p xc1
RP/0/RSP0/CPU0:T-PE1(config-l2vpn-xc-p2p)# interface gigabitethernet 0/1/0/0.1
RP/0/RSP0/CPU0:T-PE1(config-l2vpn-xc-p2p)# neighbor 10.165.200.254 pw-id 100
RP/0/RSP0/CPU0:T-PE1(config-l2vpn-xc-p2p-pw)# mpls static label local 50 remote 400
RP/0/RSP0/CPU0:T-PE1(config-l2vpn-xc-p2p-pw)# commitRP/0/RSP0/CPU0:S-PE1# configure
RP/0/RSP0/CPU0:S-PE1(config)# l2vpn
RP/0/RSP0/CPU0:S-PE1(config-l2vpn)# xconnect group MS-PW1
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-xc)# p2p ms-pw1
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-xc-p2p)# neighbor 10.165.200.225 pw-id 100
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-xc-p2p-pw)# mpls static label local 400 remote 50
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-xc-p2p-pw)# exit
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-xc-p2p)# neighbor 10.165.202.158 pw-id 300
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-xc-p2p-pw)# mpls static label local 40 remote 500
RP/0/RSP0/CPU0:S-PE1(config-l2vpn-xc-p2p-pw)# commitRP/0/RSP0/CPU0:T-PE2# configure
RP/0/RSP0/CPU0:T-PE2(config)# l2vpn
RP/0/RSP0/CPU0:T-PE2(config-l2vpn)# xconnect group XCON1
RP/0/RSP0/CPU0:T-PE2(config-l2vpn-xc)# p2p xc1
RP/0/RSP0/CPU0:T-PE2(config-l2vpn-xc-p2p)# interface gigabitethernet 0/2/0/0.4
RP/0/RSP0/CPU0:T-PE2(config-l2vpn-xc-p2p)# neighbor 10.165.200.254 pw-id 300
RP/0/RSP0/CPU0:T-PE2(config-l2vpn-xc-p2p-pw)# mpls static label local 500 remote 40
RP/0/RSP0/CPU0:T-PE2(config-l2vpn-xc-p2p-pw)# commitThis example shows how to configure preferred tunnel path:
configure
l2vpn
pw-class path1
encapsulation mpls
preferred-path interface tunnel tp 50 fallback disableThis section provides examples for:
This sample configuration shows how to configure preferred tunnel path:
l2vpn
pw-class foo
encapsulation mpls
preferred-path interface tunnel-tp 100 fallback disable
commitThis sample configuration shows how to configure PW status OAM functionality:
l2vpn
pw-oam refresh transmit 100
commit
RP/0/RSP0/CPU0:router# show l2vpn xconnect
Legend: ST = State, UP = Up, DN = Down, AD = Admin Down, UR = Unresolved,
LU = Local Up, RU = Remote Up, CO = Connected
XConnect Segment 1 Segment 2
Group Name ST Description ST Description ST
------------------------ ------------------------- -------------------------
MS-PW1 ms-pw1 UP 70.70.70.70 100 UP 90.90.90.90 300 UP
--------------------------------------------------------------------------------RP/0/RSP0/CPU0:router# show l2vpn xconnect detail
Group MS-PW1, XC ms-pw1, state is up; Interworking none
PW: neighbor 70.70.70.70, PW ID 100, state is up ( established )
PW class not set
Encapsulation MPLS, protocol LDP
PW type Ethernet VLAN, control word enabled, interworking none
PW backup disable delay 0 sec
Sequencing not set
PW Status TLV in use
MPLS Local Remote
------------ ------------------------------ -----------------------------
Label 16004 16006
Group ID 0x2000400 0x2000700
Interface GigabitEthernet0/1/0/2.2 GigabitEthernet0/1/0/0.3
MTU 1500 1500
Control word enabled enabled
PW type Ethernet VLAN Ethernet VLAN
VCCV CV type 0x2 0x2
(LSP ping verification) (LSP ping verification)
VCCV CC type 0x5 0x7
(control word) (control word)
(router alert label)
(TTL expiry) (TTL expiry)
------------ ------------------------------ -----------------------------
Incoming Status (PW Status TLV):
Status code: 0x0 (Up) in Notification message
Outgoing PW Switching TLVs (Label Mapping message):
Local IP Address: 80.80.80.80, Remote IP address: 90.90.90.90, PW ID: 300
Description: S-PE1 MS-PW between 70.70.70.70 and 90.90.90.90
Outgoing Status (PW Status TLV):
Status code: 0x0 (Up) in Notification message
Statistics:
packet totals: receive 0
byte totals: receive 0
Create time: 04/04/2008 23:18:24 (00:01:24 ago)
Last time status changed: 04/04/2008 23:19:30 (00:00:18 ago)
PW: neighbor 90.90.90.90, PW ID 300, state is up ( established )
PW class not set
Encapsulation MPLS, protocol LDP
PW type Ethernet VLAN, control word enabled, interworking none
PW backup disable delay 0 sec
Sequencing not set
PW Status TLV in use
MPLS Local Remote
------------ ------------------------------ -----------------------------
Label 16004 16006
Group ID 0x2000800 0x2000200
Interface GigabitEthernet0/1/0/0.3 GigabitEthernet0/1/0/2.2
MTU 1500 1500
Control word enabled enabled
PW type Ethernet VLAN Ethernet VLAN
VCCV CV type 0x2 0x2
(LSP ping verification) (LSP ping verification)
VCCV CC type 0x5 0x7
(control word) (control word)
(router alert label)
(TTL expiry) (TTL expiry)
------------ ------------------------------ -----------------------------
Incoming Status (PW Status TLV):
Status code: 0x0 (Up) in Notification message
Outgoing PW Switching TLVs (Label Mapping message):
Local IP Address: 80.80.80.80, Remote IP address: 70.70.70.70, PW ID: 100
Description: S-PE1 MS-PW between 70.70.70.70 and 90.90.90.90
Outgoing Status (PW Status TLV):
Status code: 0x0 (Up) in Notification message
Statistics:
packet totals: receive 0
byte totals: receive 0
Create time: 04/04/2008 23:18:24 (00:01:24 ago)
Last time status changed: 04/04/2008 23:19:30 (00:00:18 ago)This example shows you how to configure Any Transport over MPLS (AToM):
config
l2vpn
xconnect group test
p2p test
interface POS 0/1/0/0.1
neighbor 10.1.1.1 pw-id 100This example shows you how to configure IP interworking:
config
l2vpn
xconnect group test
p2p test
interworking ipv4This example shows you how to configure PPP IP interworking:
interface Serial0/2/1/0/1/1/1:0
encapsulation ppp
l2transport
!
!
interface Serial0/0/0/0/2/1/1:0
encapsulation ppp
l2transport
!
!
!! Local Switching Configuration
l2vpn
xconnect group ppp_ip_ls
p2p 1
interface Serial0/2/1/0/1/1/1:0
interface GigabitEthernet0/0/0/1.1
interworking ipv4
!
!! PW Configuration
l2vpn
xconnect group ppp_ip_iw
p2p 1
interface Serial0/0/0/0/2/1/1:0
neighbor 120.120.120.120 pw-id 3
pw-class class1
!
interworking ipv4This example shows you how to configure cHDLC IP interworking:
interface Serial0/2/1/0/1/1/2:0
l2transport
interface Serial0/0/0/0/2/1/2:0
l2transport
!! Local Switching Configuration
l2vpn
xconnect group ppp_ip_ls
p2p 1
interface Serial0/2/1/0/1/1/2:0
interface GigabitEthernet0/0/0/2.1
interworking ipv4
!
!! PW Configuration
l2vpn
xconnect group ppp_ip_iw
p2p 1
interface Serial0/0/0/0/2/1/2:0
neighbor 120.120.120.120 pw-id 3
pw-class class1
!
interworking ipv4This example shows you how to configure MLPPP IP interworking:
interface Multilink0/2/1/0/1
multilink
l2transport
!
interface Multilink0/2/1/0/51
Multilink
l2transport
!! Local Switching Configuration
l2vpn
xconnect group mlppp_ip_ls
p2p 1
interface Multilink0/2/1/0/1
interface GigabitEthernet0/0/0/1.151
interworking ipv4
!
!! PW Configuration
l2vpn
xconnect group mlppp_ip_iw
p2p 151
interface Multilink0/2/1/0/51
neighbor 140.140.140.140 pw-id 151
pw-class test
!
interworking ipv4
!
This example shows you how to configure Circuit Emulation Over Packet Switched Network:
l2vpn
xconnect group gr1
p2p p1
interface CEM 0/0/0/0:10
neighbor 3.3.3.3 pw-id 11
!
! l2vpn
pw-class class-cem
encapsulation mpls
protocol ldp
!
!
xconnect group gr1
p2p p1
interface CEM0/0/0/0:20
neighbor 1.2.3.4 pw-id 11
pw-class class-cem
! l2vpn
pw-status
commit l2vpn
pw-status disable
commit l2vpn
pw-status
pw-class class-cem
encapsulation mpls
protocol ldp
!
!
xconnect group gr1
p2p p1
interface CEM0/0/0/0:20
neighbor 1.2.3.4 pw-id 11
pw-class class-cem
backup neighbor 9.9.9.9 pw-id 1221
pw-class class-cem
!
!This example shows how to configure L2VPN Nonstop Routing.
config
l2vpn
nsr
logging nsr This example shows how to enable pseudowire grouping.
config
l2vpn
pw-groupingThis section provides examples for:
To support IPv6 pseudowire neighbors, an AFI needs to be configured as follows:
l2vpn
xconnect group g1
p2p xc3
interface GigabitEthernet0/0/0/4.2
neighbor ipv6 1111:2222::cdef pw-id 1For L2TPv3 tunnels, the encapsulation and protocol has to be set to l2tpv3.
Note |
The default encapsulation and protocol is MPLS. |
l2vpn
pw-class ts
encapsulation l2tpv3
protocol l2tpv3This example shows how to configure source IPv6 address for the L2TPv3 over IPv6 tunnel:
l2vpn
xconnect group g1
p2p xc3
interface GigabitEthernet0/0/0/4.2
neighbor ipv6 1111:2222::cdef pw-id 1
source 1111:2222::abcd
For L2TPv3 over IPv6 tunnels, the local and remote session ID is configured under the pseudowire; however, this configuration is optional.
l2vpn
xconnect group g1
p2p xc3
interface GigabitEthernet0/0/0/4.2
neighbor ipv6 1111:2222::cdef pw-id 1
l2tp static local session 1
l2tp static remote session 1For L2TPv3 over IPv6 tunnels, the local and remote cookies are configured under the pseudowire. Support has been extended for cookie roll-over that provides the ability to configure a secondary local cookie. This example shows how to configure a cookie with size 0:
l2vpn
xconnect group g1
p2p xc3
interface GigabitEthernet0/0/0/4.2
neighbor ipv6 1111:2222::cdef pw-id 1
l2tp static local cookie size 0
l2tp static remote cookie size 0This example shows how to configure a cookie with size 4:
l2vpn
xconnect group g1
p2p xc3
interface GigabitEthernet0/0/0/4.2
neighbor ipv6 1111:2222::cdef pw-id 1
l2tp static local cookie size 4 value <0x0-0xffffffff>
l2tp static remote cookie size 4 value <0x0-0xffffffff>This example shows how to configure a cookie with size 8 (the lower 4 bytes are entered first; followed by the higher 4 bytes):
l2vpn
xconnect group g1
p2p xc3
interface GigabitEthernet0/0/0/4.2
neighbor ipv6 1111:2222::cdef pw-id 1
l2tp static local cookie size 8 value <0x0-0xffffffff> <0x0-0xffffffff>
l2tp static remote cookie size 8 value <0x0-0xffffffff> <0x0-0xffffffff>To support cookie roll-over on L2TPv3 over IPv6 tunnels, configure a secondary local cookie. The local cookie secondary command specifies the secondary cookie value on the local router.
Note |
The primary and secondary cookies must be of the same size. Primary or secondary local cookies must match the cookie value being received from the remote end, otherwise, packets are dropped. |
l2vpn
xconnect group g1
p2p xc3
interface GigabitEthernet0/0/0/4.2
neighbor ipv6 1111:2222::cdef pw-id 1
l2tp static local cookie secondary size 8 value <0x0-0xffffffff> <0x0-0xffffffff>This example shows you how to enable the L2TP static submode:
l2vpn
xconnect group g1
p2p xc3
interface GigabitEthernet0/0/0/4.2
neighbor ipv6 1111:2222::cdef pw-id 1
l2tp static
local cookie <>For L2TPv3 over IPv6 tunnels, configurations are supported for each pseudowire class to enable type of service (TOS) reflection, or to set a specific TOS value in the L2TPv3 header.
Note |
By default, the TOS is copied over from the class of service (COS) fields of the VLAN header. If the underlying packet is not an IPv4 or IPv6 packet, the COS fields are copied from the VLAN header, even if a TOS reflection is configured. |
This example shows how to configure a TOS reflection in the L2TPv3 header:
l2vpn
pw-class ts
encapsulation l2tpv3
protocol l2tpv3
tos reflect
This example shows how to set a TOS value in the L2TPv3 header:
l2vpn
pw-class ts
encapsulation l2tpv3
protocol l2tpv3
tos value 64For L2TPv3 over IPv6 tunnels, TTL configuration is supported in the pseudowire class.
l2vpn
pw-class ts
encapsulation l2tpv3
protocol l2tpv3
ttl <1-255>This example associates an EFP to a monitor-session:
interface GigabitEthernet0/0/0/4.2 l2transport
monitor-session customer-fooLayer 2 SPAN is supported on L3 interfaces; however, the Layer 2 frame is mirrored:
interface GigabitEthernet0/0/0/4.2
ipv6 address <>
monitor-session customer-fooSPAN is also supported on main interfaces.
interface GigabitEthernet0/4/0/3
l2transport
monitor-session customer-fooThis example creates the monitor-session globally:
monitor-session customer-foo
destination pseudowireThis example creates a cross-connect between the monitor-session and a L2TPv3 over IPv6 tunnel:
l2vpn
xconnect group span
p2p span-foo
monitor-session customer-foo
neighbor ipv6 1111:3333::cdef pw-id 1001
pw-class ts
source 1111:3333::abcd
l2tp static local cookie size 8 value 0xabcd 0x1234
l2tp static remote cookie size 8 value 0xcdef 0x5678For more information on:
Configuration procedures, see Configuring L2TPv3 over IPv6Tunnels
This section provides examples for:
Perform this task to configure a dynamic L2TPv3 pseudowire connecting to a remote IPv4 peer.
|
Step 1 |
configure Example:Enters the Global Configuration mode. |
|
Step 2 |
l2vpn Example:Enter L2VPN configure submode. |
|
Step 3 |
xconnect group name Example:Enter a name for the cross-connect group. |
|
Step 4 |
p2p name Example:Enters p2p configuration submode to configure point-to-point cross-connects. |
|
Step 5 |
interface type interface-path-id Example:Specifies the interface type ID. The choices are:
|
|
Step 6 |
neighbor ipv4 ip-address pw-id number Example:Configures a pseudowire for a cross-connect. |
|
Step 7 |
pw-class pw-class-name Example:Enters pseudowire class submode to define a name for the cross-connect. |
|
Step 8 |
Use the commit or end command. commit - Saves the configuration changes and remains within the configuration session. end - Prompts user to take one of these actions:
|
This example shows how to set the encapsulation and protocol for L2TPv3 tunnels:
configure
l2vpn
pw-class L2TPV3_V4_CLASS
encapsulation l2tpv3
protocol l2tpv3 class L2TP-CLASS
dfbit set
ipv4 source 25.25.25.25
cookie size 4
!
!
The following example shows a typical L2TPv3 control-channel configuration:
configure
l2tp-class L2TP-CLASS
authentication
retransmit retries 5
retransmit initial retries 10
retransmit initial timeout max 5
retransmit timeout max 6
hidden
password 7 1511021F07257A767B
hello-interval 10
digest hash MD5
!
The following example shows how to configure EVPN-VPWS service.
RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# xconnect group pw-he1
RP/0/RSP0/CPU0:router(config-l2vpn-xc)# p2p pw-ss
RP/0/RSP0/CPU0:router(config-l2vpn-xc-p2p)# interface gigabitethernet 0/1/0/9
RP/0/RSP0/CPU0:router(config-l2vpn-xc-p2p)# neighbor evpn evi 100 target 12 source 10
The following example shows how to configure EVPN-VPWS into PWHE interface.
RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# xconnect group xg1
RP/0/RSP0/CPU0:router(config-l2vpn-xc)# p2p pwhe1
RP/0/RSP0/CPU0:router(config-l2vpn-xc-p2p)# interface PW-Ether 1
RP/0/RSP0/CPU0:router(config-l2vpn-xc-p2p)# neighbor evpn evi 2 target 20 source 20The following example shows how a bridge-domain can configure an access pseudowire using EVPN-VPWS.
RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# bridge group bg1
RP/0/RSP0/CPU0:router(config-l2vpn-bg)# bridge-domain bd1
RP/0/RSP0/CPU0:router(config-l2vpn-bg-bd)# neighbor evpn evi 1 target 100
Feedback