This section includes show commands for ACR:
The following example shows the acr groups that have been configured or deleted:
Router# show acr group
ACR Group Working I/f Protect I/f Currently Active Status
--------------------------------------------------------------------------
1 SONET 4/1/0 SONET 3/1/0 SONET 4/1/0
The following example shows the configured working and protect cem interfaces under the ACR controller:
Router# show acr group 1 detail cem
ACR Group Working I/f Protect I/f Currently Active Status
--------------------------------------------------------------------------
CE1 CEM4/1/0 CEM3/1/0 CEM4/1/0
CEM CKT Details
Cktid State on Working State on Protect
1 Provision Success Provision Success
The following example shows the configuration under the ACR controller:
Example of a configuration using CESoP:
Router# show running-config | sec SONET-ACR 1
controller SONET-ACR 1
framing sdh
aug mapping au-4
!
au-4 1 tug-3 1
tug-2 1 e1 1 cem-group 0 timeslots 1-31
Example of a configuration using SAToP:
Router# show running-config | sec SONET-ACR 2
controller SONET-ACR 2
framing sdh
aug mapping au-4
!
au-4 1 tug-3 1
tug-2 1 e1 1 cem-group 1001 unframed
The following example shows the loopback ip address for the router:
Router# show ip interface brief | i Loopback
Loopback0 22.22.22.22 YES NVRAM up up
The following example shows the cem-acr circuit status:
Router# show cem circuit
CEM Int. ID Ctrlr Admin Circuit AC
--------------------------------------------------------------
CEM-ACR1 1 UP UP Active UP
CEM-ACR1 2 UP UP Active UP
CEM-ACR1 3 UP UP Active UP
CEM-ACR1 4 UP UP Active UP
CEM-ACR1 5 UP UP Active UP
CEM-ACR1 6 UP UP Active UP
CEM-ACR1 7 UP UP Active UP
CEM-ACR1 8 UP UP Active UP
The following example shows the cem-acr circuit details for cem-group 0 under the CEM-ACR interface:
Router# show cem circuit int cem-acr 1 0
CEM-ACR1, ID: 0, Line: UP, Admin: UP, Ckt: ACTIVE
Controller state: up, T1/E1 state: up
Idle Pattern: 0xFF, Idle CAS: 0x8
Dejitter: 8 (In use: 0)
Payload Size: 32
Framing: Framed (DS0 channels: 1)
CEM Defects Set
None
Signalling: No CAS
RTP: No RTP
Ingress Pkts: 774186 Dropped: 0
Egress Pkts: 774187 Dropped: 0
CEM Counter Details
Input Errors: 0 Output Errors: 0
Pkts Missing: 0 Pkts Reordered: 0
Misorder Drops: 0 JitterBuf Underrun: 0
Error Sec: 0 Severly Errored Sec: 0
Unavailable Sec: 0 Failure Counts: 0
Pkts Malformed: 0 JitterBuf Overrun: 0
The following example shows the cem-acr circuit details for cem-group 1001 under the CEM-ACR interface:
Router# show cem circuit int cem-acr 1 1001
CEM-ACR1, ID: 1001, Line: UP, Admin: UP, Ckt: ACTIVE
Controller state: up, T1/E1 state: up
Idle Pattern: 0xFF, Idle CAS: 0x8
Dejitter: 5 (In use: 0)
Payload Size: 256
Framing: Unframed
CEM Defects Set
None
Signalling: No CAS
RTP: No RTP
Ingress Pkts: 3096748 Dropped: 0
Egress Pkts: 3096748 Dropped: 0
CEM Counter Details
Input Errors: 0 Output Errors: 0
Pkts Missing: 0 Pkts Reordered: 0
Misorder Drops: 0 JitterBuf Underrun: 0
Error Sec: 0 Severly Errored Sec: 0
Unavailable Sec: 0 Failure Counts: 0
Pkts Malformed: 0 JitterBuf Overrun: 0
The following example shows the mpls l2 transport vc details for the specified vc. In this case it is the vc with vc-id =
1001:
Router# show mpls l2 vc 1001 det
Local interface: CE1 up, line protocol up, CESoPSN Basic 0 up
Destination address: 66.66.66.66, VC ID: 1001, VC status: up
Output interface: Te0/2/0, imposed label stack {1629}
Preferred path: not configured
Default path: active
Next hop: 61.1.1.2
Create time: 03:28:57, last status change time: 03:27:37
Last label FSM state change time: 00:51:41
Signaling protocol: LDP, peer 66.66.66.66:0 up
Targeted Hello: 22.22.22.22(LDP Id) -> 66.66.66.66, LDP is UP
Graceful restart: configured and enabled
Non stop routing: not configured and not enabled
Status TLV support (local/remote) : enabled/supported
LDP route watch : enabled
Label/status state machine : established, LruRru
Last local dataplane status rcvd: No fault
Last BFD dataplane status rcvd: Not sent
Last BFD peer monitor status rcvd: No fault
Last local AC circuit status rcvd: No fault
Last local AC circuit status sent: No fault
Last local PW i/f circ status rcvd: No fault
Last local LDP TLV status sent: No fault
Last remote LDP TLV status rcvd: No fault
Last remote LDP ADJ status rcvd: No fault
MPLS VC labels: local 586, remote 1629
Group ID: local 0, remote 0
MTU: local 0, remote 0
Remote interface description:
Sequencing: receive disabled, send disabled
Control Word: On (configured: autosense)
SSO Descriptor: 66.66.66.66/1001, local label: 586
Dataplane:
SSM segment/switch IDs: 1410842/2339386 (used), PWID: 571
VC statistics:
transit packet totals: receive 3119684, send 3112390
transit byte totals: receive 155984200, send 130720380
transit packet drops: receive 0, seq error 0, send 0
The following example shows the mpls l2 transport vc details for the specified vc. In this case it is the vc with vc-id =
5001:
Router# show mpls l2 vc 5001 det
Local interface: CE1 up, line protocol up, SATOP E1 1001 up
Destination address: 66.66.66.66, VC ID: 5001, VC status: up
Output interface: Te0/2/0, imposed label stack {1613}
Preferred path: not configured
Default path: active
Next hop: 61.1.1.2
Create time: 03:29:05, last status change time: 03:27:45
Last label FSM state change time: 00:51:49
Signaling protocol: LDP, peer 66.66.66.66:0 up
Targeted Hello: 22.22.22.22(LDP Id) -> 66.66.66.66, LDP is UP
Graceful restart: configured and enabled
Non stop routing: not configured and not enabled
Status TLV support (local/remote) : enabled/supported
LDP route watch : enabled
Label/status state machine : established, LruRru
Last local dataplane status rcvd: No fault
Last BFD dataplane status rcvd: Not sent
Last BFD peer monitor status rcvd: No fault
Last local AC circuit status rcvd: No fault
Last local AC circuit status sent: No fault
Last local PW i/f circ status rcvd: No fault
Last local LDP TLV status sent: No fault
Last remote LDP TLV status rcvd: No fault
Last remote LDP ADJ status rcvd: No fault
MPLS VC labels: local 865, remote 1613
Group ID: local 0, remote 0
MTU: local 0, remote 0
Remote interface description:
Sequencing: receive disabled, send disabled
Control Word: On (configured: autosense)
SSO Descriptor: 66.66.66.66/5001, local label: 865
Dataplane:
SSM segment/switch IDs: 2176983/3482449 (used), PWID: 850
VC statistics:
transit packet totals: receive 12488973, send 12445403
transit byte totals: receive 3347044764, send 3285586392
transit packet drops: receive 0, seq error 0, send 0
The following example shows the currently configured APS groups on the router:
Router# show aps
SONET 0/5/2 APS Group 25: protect channel 0 (Inactive) (HA)
Working channel 1 at 1.1.1.1 (Enabled) (HA)
bidirectional, non-revertive
PGP timers (extended for HA): hello time=1; hold time=10
hello fail revert time=120
SDH framing; SDH MSP signalling by default
Received K1K2: 0x00 0x05
No Request (Null)
Transmitted K1K2: 0x00 0x00
No Request (Null)
Remote APS configuration: (null)
SONET 0/0/2 APS Group 25: working channel 1 (Active) (HA)
Protect at 1.1.1.1
PGP timers (from protect): hello time=1; hold time=10
SDH framing
Remote APS configuration: (null)
The following example shows ATM ACR configuration on the router:
Router# show running-config | sec ACR
controller SONET-ACR 1
framing sdh
aug mapping au-4
!
au-4 1 tug-3 1
mode c-12
tug-2 1 e1 1 atm
!
au-4 1 tug-3 2
mode c-12
!
au-4 1 tug-3 3
mode c-12
interface ATM-ACR1.1/1/1/1
no ip address
pvp 1/99 l2transport
xconnect 51.1.1.2 3 encapsulation mpls
The following example shows ATM ACR interfaces on the router:
Router# show interface ATM0/1/1.1/1/1/1 | in pac
5 minute input rate 4000 bits/sec, 10 packets/sec
5 minute output rate 4000 bits/sec, 10 packets/sec
3000 packets input, 156000 bytes, 0 no buffer
3000 packets output, 156000 bytes, 0 underruns
Router# show xconnect all
Legend: XC ST=Xconnect State S1=Segment1 State S2=Segment2 State
UP=Up DN=Down AD=Admin Down IA=Inactive
SB=Standby HS=Hot Standby RV=Recovering NH=No Hardware
XC ST Segment 1 S1 Segment 2 S2
------+---------------------------------+--+---------------------------------+--
PN pri ac AT1.1/1/1:10/10(ATM AAL5) UP mpls 3.3.3.3:1 UP
Router# show atm pvc
Keys: CI = ATM0/3/2.1/1/1, CH = ATM0/4/2.1/1/1, CG = ATM-ACR1.1/1/1,
VCD / Peak Av/Min Burst
Interface Name VPI VCI Type Encaps SC Kbps Kbps Cells St
CG 1 10 10 PVC AAL5 UBR 1536 UP