Hot Standby Pseudowire Support for ATM and TDM Access Circuits


Note

Hot Standby Pseudowire Support for ATM and IMA circuits are not supported on the Cisco ASR 900 RSP3 module.

The Hot Standby Pseudowire Support for ATM and TDM Access Circuits feature is an enhancement to the L2VPN Pseudowire Redundancy feature in the following ways:

  • Faster failover of to the backup pseudowire

  • Less traffic loss during failover

The Hot Standby Pseudowire Support for ATM and TDM Access Circuits feature allows the backup pseudowire to be in a “hot standby” state, so that it can immediately take over if the primary pseudowire fails. The following sections explain the concepts and configuration tasks for this feature.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.

Prerequisites for Hot Standby Pseudowire Support for ATM and TDM Access Circuits

  • This feature requires that you understand how to configure Layer 2 virtual private networks (VPNs). You can find that information in the following documents:
    • Any Transport over MPLS
    • L2 VPN Interworking
    • L2VPN Pseudowire Redundancy
  • The Hot Standby Pseudowire Support for ATM and TDM Access Circuits feature recommends that the following mechanisms be in place to enable faster detection of a failure in the network:
    • Label-switched paths (LSP) Ping/Traceroute and Any Transport over MPLS Virtual Circuit Connection Verification (AToM VCCV)
    • Local Management Interface (LMI)
    • Operation, Administration, and Maintenance (OAM)

Restrictions for Hot Standby Pseudowire Support for ATM and TDM Access Circuits

  • Hot Standby Pseudowire Support for ATM and TDM Access Circuits is not supported on L2TPv3. Only MPLS L2VPNs are supported.

  • Hot Standby Pseudowire Support for ATM and IMA is not supported on the Cisco ASR 900 RSP3 module.

  • More than one backup pseudowire is not supported.

  • Different pseudowire encapsulation types on the MPLS pseudowire are not supported.

  • If you use Hot Standby Pseudowire Support for ATM and TDM Access Circuits with L2VPN Interworking, the interworking method must be the same for the primary and backup pseudowires. For TDM access circuits, interworking is not supported.

  • Only dynamic pseudowires are supported.

  • Pseudowire over static VPLS is not supported on the Cisco ASR 900 RSP3 module.

Information About Hot Standby Pseudowire Support for ATM and TDM Access Circuits

How the Hot Standby Pseudowire Support for ATM and TDM Access Circuits Feature Works

The Hot Standby Pseudowire Support for ATM and TDM Access Circuits feature improves the availability of L2VPN pseudowires by detecting failures and handling them with minimal disruption to the service.

The Hot Standby Pseudowire Support for ATM and TDM Access Circuits feature allows the backup pseudowire to be in a “hot standby” state, so that it can immediately take over if the primary pseudowire fails. The L2VPN Pseudowire Redundancy feature allows you to configure a backup pseudowire too, but in a cold state. With the L2VPN Pseudowire Redundancy feature, if the primary pseudowire fails, it takes time for the backup pseudowire to take over, which causes a loss in traffic.

If you have configured L2VPN Pseudowire Redundancy on your network and upgrade to Cisco IOS Release 15.1(1)S, you do not need add any other commands to achieve Hot Standby Pseudowire Support for ATM and TDM Access Circuits. The backup pseudowire will automatically be in a hot standby state.

Supported Transport Types

The Hot Standby Pseudowire Support for ATM and TDM Access Circuits feature supports the following transport types:

  • ATM
    • ATM AAL5 in VC mode
    • ATM packed cell relay in VC Mode
    • ATM in VP mode
    • ATM packed cell relay in VP mode
    • ATM in port mode
    • ATM packed cell relay in port mode
  • Time division multiplexing (TDM)
    • Structure-Agnostic TDM over Packet (SAToP)
    • Circuit Emulation Services over PSN (CESoPSN)

How to Configure Hot Standby Pseudowire Support for ATM and TDM Access Circuits

The Hot Standby Pseudowire Support for ATM and TDM Access Circuits feature enables you to configure a backup pseudowire in case the primary pseudowire fails. When the primary pseudowire fails, the PE router can immediately switch to the backup pseudowire.

Configuring a Pseudowire for Static VPLS


Note

Pseudowire for Static VPLS is not supported on the Cisco ASR 900 RSP3 module.

The configuration of pseudowires between provider edge (PE) devices helps in the successful transmission of the Layer 2 frames between PE devices.

Use the pseudowire template to configure the virtual circuit (VC) type for the virtual path identifier (VPI) pseudowire. In the following task, the pseudowire will go through a Multiprotocol Label Switching (MPLS)-Tunneling Protocol (TP) tunnel.

The pseudowire template configuration specifies the characteristics of the tunneling mechanism that is used by the pseudowires, which are:

  • Encapsulation type

  • Control protocol

  • Payload-specific options

  • Preferred path

Perform this task to configure a pseudowire template for static Virtual Private LAN Services (VPLS).


Note

Ensure that you perform this task before configuring the virtual forwarding instance (VFI) peer. If the VFI peer is configured before the pseudowire class, the configuration is incomplete until the pseudowire class is configured. The show running-config command displays an error stating that configuration is incomplete. 

Device# show running-config | sec vfi

l2 vfi config manual
 vpn id 1000
 ! Incomplete point-to-multipoint vfi config

Procedure

  Command or Action Purpose
Step 1

enable

Example:


Device> enable

Enables privileged EXEC mode.

  • Enter your password if prompted.

Step 2

configure terminal

Example:


Device# configure terminal

Enters global configuration mode.

Step 3

template type pseudowire name

Example:


Device(config)# template type pseudowire static-vpls

Specifies the template type as pseudowire and enters template configuration mode.

Step 4

encapsulation mpls

Example:


Device(config-template)# encapsulation mpls
Specifies the tunneling encapsulation.
  • For Any Transport over MPLS (AToM), the encapsulation type is MPLS.
Step 5

signaling protocol none

Example:


Device(config-template)# signaling protocol none

Specifies that no signaling protocol is configured for the pseudowire class.

Step 6

preferred-path interface Tunnel-tp interface-number

Example:


Device(config-template)# preferred-path interface Tunnel-tp 1

(Optional) Specifies the path that traffic uses: an MPLS Traffic Engineering (TE) tunnel or destination IP address and Domain Name Server (DNS) name.

Step 7

exit

Example:


Device(config-template)# exit

Exits template configuration mode and returns to global configuration mode.

Step 8

interface pseudowire number

Example:


Device(config)# interface pseudowire 1

Establishes a pseudowire interface and enters interface configuration mode.

Step 9

source template type pseudowire name

Example:


Device(config-if)# source template type pseudowire static-vpls

Configures the source template type of the configured pseudowire.

Step 10

neighbor peer-address vcid-value

Example:


Device(config-if)# neighbor 10.0.0.1 123

Specifies the peer IP address and VC ID value of a Layer 2 VPN (L2VPN) pseudowire.

Step 11

label local-pseudowire-label remote-pseudowire-label

Example:


Device(config-if)# label 301 17

Configures an Any Transport over MPLS (AToM) static pseudowire connection by defining local and remote circuit labels.

Step 12

end

Example:


Device(config-if)# end

Exits interface configuration mode and returns to privileged EXEC mode.

Configuring Hot Standby Pseudowire Support for ATM and TDM Access Circuits

Use the following steps to configure the Hot Standby Pseudowire Support for ATM and TDM Access Circuits feature.

Procedure

  Command or Action Purpose
Step 1

enable

Example:


Router> enable

Enables privileged EXEC mode.

  • Enter your password if prompted.

Step 2

configure terminal

Example:


Router# configure terminal

Enters global configuration mode.

Step 3

interface atm number

Example:


Router(config)# interface atm4/1/0

Specifies the ATM interface and enters interface configuration mode.

Step 4

pvc [name ] vpi/vci l2transport

Example:


Router(config-if)# pvc 1/100 l2transport

Creates or assigns a name to an ATM PVC and enters L2transport PVC configuration mode.

Step 5

xconnect peer-router-id vcid {encapsulation mpls | pw-class pw-class-name}

Example:


Router(config-if-atm-l2trans-pvc)# xconnect 10.0.0.1 123 pw-class atom

Binds the attachment circuit to a pseudowire VC.

Step 6

backup peer peer-router-ip-addr vcid [pw-class pw-class-name ]

Example:


Router(config-if-atm-l2trans-pvc)# backup peer 10.0.0.3 125 pw-class atom

Specifies a redundant peer for the pseudowire VC.

The pseudowire class name must match the name you specified when you created the pseudowire class, but you can use a different pw-class in the backup peer command than the name that you used in the primary xconnect command.

Step 7

backup delay enable-delay {disable-delay | never }

Example:


Router(config-if-atm-l2trans-pvc)# backup delay 5 never

Specifies how long (in seconds) the backup pseudowire VC should wait to take over after the primary pseudowire VC goes down. The range is 0 to 180.

Specifies how long the primary pseudowire should wait after it becomes active to take over for the backup pseudowire VC. The range is 0 to 180 seconds. If you specify the never keyword , the primary pseudowire VC never takes over for the backup.

Verifying the Hot Standby Pseudowire Support for ATM and TDM Access Circuits Configuration

Use the following commands to verify that the backup pseudowire is provisioned for hot standby support.

Procedure

Step 1

show atm acircuit

If the output of the show atm acircuit command shows two entries for the same vpi/vci, then the backup pseudowire has been correctly provisioned, as shown in the following example:

Example:


Router# show atm acircuit
 
Interface          VPI  VCI    AC    Id      Switch   Segment  St  Flg  Prov
---------          ---  ---    --    --      -------  -------- --  ---  ----
ATM2/1/0.2         11   111    ATA5  1        2003    4007     2    0    Y 
ATM2/1/0.2         11   111    ATA5  1        1002    3006     2    0    Y
Step 2

show atm pvc

If the output of the show atm pvc command includes “Red Prov: Yes,” then the backup p seudowire has been correctly provisioned, as shown in bold in the following example:

Example:


Router# show atm pvc 1/1010
Interworking Method: like to like
AC Type: ATM AAL5,  Circuit Id: 2,  AC State: UP,  Prov: YES
Switch Hdl: 0x1005,  Segment hdl: 0x4011
Red Switch Hdl: 0x3007, Red Segment hdl: 0x6010, Red Prov: YES
AC Hdl: 0x7200000F,  AC Peer Hdl: 0x5D000012,  Flg:0,  Platform Idx:10
Status: UP
Step 3

show cem acircuit

If the output of the show cem acircuit command includes “Redundancy Member Prov: Yes,” then the backup p seudowire has been correctly provisioned, as shown in bold in the following example:

Example:


Router# show cem acircuit
CEM Int.   ID  Flags  Swhdl    Seghdl    Ckttype  Provisioned 
---------------------------------------------------------------- 
CEM3/0/0   1    0    B00E       201E       19        Yes
Redundancy Switch hdl: 0xC00F Redundancy Segment hdl: 0x401F   Redundancy Member Prov: Yes
Step 4

show cem acircuit detail

If the output of the show cem acircuit detail command includes “Redundancy Member Prov: Yes,” then the backup p seudowire has been correctly provisioned, as shown in bold in the following example:

Example:


Router# show cem acircuit detail
 
CEM3/0/0    Cemid 1    
PW Ckt_type: 19  Aie hdl: EE00000B Peer aie hdl: 0x2000000C 
Switch hdl: 0xB00E     Segment hdl: 0x201E     Redundancy Switch hdl: 0x1000     Redundancy Segment hdl: 0x4002     Redundancy Member Prov: Yes

Configuration Examples for Hot Standby Pseudowire Support for ATM and TDM Access Circuits

Configuring Hot Standby Pseudowire Support for ATM and TDM Access Circuits on CEM Circuits Example

The figure below shows the configuration of Hot Standby Pseudowire Support for ATM and TDM Access Circuits, where the backup pseudowire is on the same PE router.

Figure 1. Hot Standby Pseudowire Topology

The configuration shown in the figure above is used in the following examples:

Table 1. Configuring Hot Standby Pseudowire Support for ATM and TDM Access Circuits on CEM Circuits: Example

PE1

PE2 


interface Loopback0
 ip address 10.4.4.4 255.255.255.255
!
Controller E1 9/2/0
 clock source internal
 cem-group 0 timeslots 1-4
!
pseudowire-class atom
 encapsulation mpls
!
interface CEM9/2/0
 no ip address
 class int cesopsn_1
 cem 0
  xconnect 10.2.2.2 5000 pw-class atom
   backup peer 10.2.2.2 5005 pw-class atom
   backup delay 0 5


interface Loopback0
 ip address 10.2.2.2 255.255.255.255
!
Controller E1 2/2/0
 clock source internal
 cem-group 0 timeslots 1-4  <<<<<< Primary 
 cem-group 5 timeslots 21-24<<<<< Backup
!
interface CEM2/2/0
 no ip address
 class int cesopsn_1
 cem 0<<<<<<<<<< Primary
  service-policy input cem_exp_6
  xconnect 10.4.4.4 5000 encapsulation mpls
!
cem 5<<<<<<<<<< Backup
  xconnect 10.4.4.4 5005 encapsulation mpls
Table 2. Configuring Hot Standby Pseudowire Support for ATM and TDM Access Circuits on ATM Circuits: Example

PE1

PE2 


interface Loopback0
 ip address 10.44.44.44 255.255.255.255
!
interface POS3/3/0
 ip address 10.4.4.4 255.255.255.0
 mpls ip
!
interface ATM4/1/0
 no ip address
 no atm enable-ilmi-trap
 pvc 1/100 l2transport
  xconnect 10.22.22.22 1 encapsulation mpls
   backup peer 10.22.22.22 2


interface Loopback0
 ip address 10.22.22.22 255.255.255.255
!
interface POS3/3/0
 ip address 10.4.4.1 255.255.255.0
 mpls ip
!
interface ATM4/1/0
 no ip address
 no atm enable-ilmi-trap
 pvc 1/100 l2transport
  xconnect 10.44.44.44 1 encapsulation mpls
!
 pvc 1/200 l2transport
  xconnect 10.44.44.44 2 encapsulation mpls