1 port OC-48/STM-16 or 4 port OC-12/OC-3 / STM-1/STM-4 + 12 port T1/E1 + 4 port T3/E3 CEM Interface Module Configuration Guide, Cisco IOS XE 16 (ASR 920 Series Routers)

Restrictions for STS-1e

Only 16 BERT Patterns can be configured at a time.
PMON fields are not supported for VT1.5 VT and DS3 or T3.
PMON Far-end parameters are not supported.
APS and card-protection are not supported for STS-1e port.
In unframed mode, ACR and DCR are not supported.
CESoPSN is not supported.
Framed SAToP is not supported.

Restrictions for Clock Source Configuration

Only 4 ports can be configured in STS-1e line for clock source configuration per chassis.
You should configure the clock source line and network-clock sync together to receive the clock from a remote port that is connected to the STS-1e port.

Prerequisites for Configuring STS-1e

You must select the MediaType controller to configure and enter the controller configuration mode.

You must configure the controller as a STS-1e port.

Configuring MediaType Controller

To configure MediaType Controller, use the following commands:

enable
configure terminal
controller MediaType 0/0/16
mode STS-1e
end

Configuring STS-1e Modes

To configure STS-1e modes, use the following commands:

enable
configure terminal
controller sts-1e 0/0/16
sts-1 1
mode vt-15
end

Note

There is no default mode. The following modes are supported:

mode vt-15
mode ct3
mode t3
mode unframed

Note

To restore the system to its default condition, use the no form of the command.

Configuring VT-15 Mode of STS-1e

enable
configure terminal
controller STS1E 0/3/14
no ais-shut
alarm-report all
clock source internal
!
sts-1 1
clock source internal
mode vt-15
vtg 1 t1 1 framing unframed
vtg 1 t1 1 cem-group 0 unframed

Configuring DS1/T1 CT3 mode of STS-1e

To configure DS1/T1 CT3 mode of STS-1, you can configure the T1 link using the following steps:

enable
configure terminal
controller sts-1e 0/0/16
sts-1 1
mode ct3
t1 1 clock source internal
t1 1 framing unframed 
end

Note

To restore the system to its default condition, use the no form of the command.

Configuring T3 mode of STS-1e

controller STS1E 0/3/14
no ais-shut
alarm-report all
clock source internal
!
sts-1 1
clock source internal
mode t3
cem-group 0 unframed
t3 clock source internal

Configuring Unframed Mode of STS-1e

controller STS1E 0/3/14
no ais-shut
alarm-report all
clock source internal
!
sts-1 1
clock source internal
mode unframed
cem-group 0 cep

Configuring Line and Section Overhead

To configure line and section overhead, use the following commands:

enable
configure terminal
controller MediaType 0/0/16
mode sts-1e
controller sts-1e 0/0/16
overhead s1s0 2
overhead j0 tx length 1-byte
end

Note

To restore the system to its default condition, use the no form of the command.

Configuring Line Loopback

To configure loopback, use the following commands:

enable
configure terminal
controller sts-1e 0/0/16
loopback local
end

Note

To restore the system to its default condition, use the no form of the command.

Configuring AIS Shut

To configure AIS-Shut, use the following commands:

enable
configure terminal
controller sts-1e 0/0/16
ais-shut
end

Note

The no ais-shut command will not send AIS.

Configuring Shut

To configure Shut, use the following commands:

enable
configure terminal
controller sts-1e 0/0/16
shutdown
end

Note

Use the no shutdown command to disable the interface.

Configuring Clock

To configure clock, use the following commands:

enable
configure terminal
controller MediaType 0/0/16
mode sts-1e
controller sts-1e 0/0/16
clock source line
end

Note

The default mode is internal.

Note

ACR and DCR clock recovery are also supported. Refer to Clock Recovery System for SAToP for more information.

Note

To restore the system to its default condition, use the no form of the command.

Configuring Network-Clock STS-1e

To configure network-clock STS-1e, use the following commands:

enable
configure terminal
network-clock input-source 1 controller STS-1e 0/0/16
end

Verification of STS-1e Configuration

The following sample output shows the verification of STS-1e configuration in unframed mode:

router#show controllers sts1e 0/3/14
STS1E 0/3/14 is up.                               ======> this is the controller/port status.
  Hardware is A900-IMA3G-IMSG

 Port configured rate: OC1                       =======> this is the rate the port is configured on it.
 Applique type is Channelized STS1E
 Clock Source is Internal                         ===> the clocking config
Medium info:
  Type: STS1E, Line Coding: NRZ, 
 Alarm Throttling: OFF
 SECTION:
  LOS = 0          LOF = 0                      BIP(B1) = 0      =======> the section level alarm counter (from last clear counters)

STS1E Section Tables
  INTERVAL       CV    ES   SES  SEFS
  05:26-05:28     0    49    49    49

LINE:
  AIS = 0          RDI = 0          REI = 0          BIP(B2) = 0         =======> the line level alarm counter (from last clear counters)
Active Defects: None
Detected Alarms: None
Asserted/Active Alarms: None                                     =========> present active alarms on the port.           
Alarm reporting enabled for: SLOS SLOF LAIS SF SD LRDI B1-TCA B2-TCA 
BER thresholds:  SF = 10e-3  SD = 10e-6                          ====> ber thresholds
TCA thresholds:  B1 = 10e-6  B2 = 10e-6
Rx: S1S0 = 00
    J0 = 00 

    RX S1 = 00

Tx: S1S0 = 00
    J0 = 04

Tx J0 Length : 64
Tx J0 Trace :

  52 53 50 32 20 20 20 20 20 20 20 20 20 20 20 20     RSP2            
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20                     
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20                     
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 00 00                   ..
  
Expected J0 Length : 64
Expected J0 Trace :

  52 53 50 32 20 20 20 20 20 20 20 20 20 20 20 20     RSP2            
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20                     
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20                     
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 00 00                   ..
  
Rx J0 Length : 16
Rx J0 Trace :
  CRC-7: 0xD8 ERROR

  BC 4B 69 CC 79 24 1B 01 E8 EB 9C 36 FC 29 A9 00     .Ki.y$.....6.)..
  
STS1E Line Tables
  INTERVAL       CV    ES   SES   UAS  CVFE  ESFE  SESFE  UASFE
  05:26-05:28     0     0     0    50     0     0      0      0


High Order Path:

PATH 1:
Clock Source is internal

  AIS = 0          RDI = 0          REI = 0          BIP(B3) = 0         
  LOP = 0          PSE = 0          NSE = 0          NEWPTR = 0         
  LOM = 0          PLM = 0          UNEQ = 0         

Active Defects: None
Detected Alarms: None
Asserted/Active Alarms: None
Alarm reporting enabled for: PAIS PRDI PUNEQ PLOP PPLM LOM B3-TCA 

TCA threshold:  B3 = 10e-6
Rx: C2 = 04
Tx: C2 = 01

Tx J1 Length : 64 
Tx J1 Trace

  52 53 50 32 20 30 2F 33 2F 31 34 2E 31 00 00 00     RSP2 0/3/14.1...
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  
Expected J1 Length : 64 
Expected J1 Trace

  52 53 50 32 20 30 2F 33 2F 31 34 2E 31 00 00 00     RSP2 0/3/14.1...
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
          
PATH TRACE BUFFER : UNSTABLE 

Rx J1 Length : 64
Rx J1 Trace

  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  
SONET Path Tables
  INTERVAL       CV    ES   SES   UAS  CVFE  ESFE  SESFE  UASFE
  05:26-05:28     0     0     0    48     0     0      0      0


STS1E 0/3/14.1 PATH  mode UNFRAMED is up
  cep is configured: TRUE cem_id  :0
  clock source internal

The following sample output shows the verification of STS-1e configuration in VT-15 mode:

router#show controllers sts1e 0/3/14
STS1E 0/3/14 is up.
  Hardware is A900-IMA3G-IMSG

 Port configured rate: OC1
 Applique type is Channelized STS1E
 Clock Source is Internal
Medium info:
  Type: STS1E, Line Coding: NRZ, 
 Alarm Throttling: OFF
 SECTION:
  LOS = 0          LOF = 0                           BIP(B1) = 0

STS1E Section Tables
  INTERVAL       CV    ES   SES  SEFS
  05:33-05:33     0     0     0     0

LINE:
  AIS = 0          RDI = 0          REI = 0          BIP(B2) = 0         
Active Defects: None
Detected Alarms: None
Asserted/Active Alarms: None
Alarm reporting enabled for: SLOS SLOF LAIS SF SD LRDI B1-TCA B2-TCA 
BER thresholds:  SF = 10e-3  SD = 10e-6
TCA thresholds:  B1 = 10e-6  B2 = 10e-6
Rx: S1S0 = 00
    J0 = 00 

    RX S1 = 00

Tx: S1S0 = 00
    J0 = 04

Tx J0 Length : 64
Tx J0 Trace :

  52 53 50 32 20 20 20 20 20 20 20 20 20 20 20 20     RSP2            
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20                     
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20                     
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 00 00                   ..
  
Expected J0 Length : 64
Expected J0 Trace :

  52 53 50 32 20 20 20 20 20 20 20 20 20 20 20 20     RSP2            
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20                     
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20                     
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 00 00                   ..
  
Rx J0 Length : 16
Rx J0 Trace :
  CRC-7: 0xD8 ERROR

  BC 4B 69 CC 79 24 1B 01 E8 EB 9C 36 FC 29 A9 00     .Ki.y$.....6.)..
  
STS1E Line Tables
  INTERVAL       CV    ES   SES   UAS  CVFE  ESFE  SESFE  UASFE
  05:33-05:33     0     0     0     0     0     0      0      0


High Order Path:

PATH 1:
Clock Source is internal

  AIS = 0          RDI = 0          REI = 0          BIP(B3) = 0         
  LOP = 0          PSE = 0          NSE = 0          NEWPTR = 0         
  LOM = 0          PLM = 0          UNEQ = 0         

Active Defects: None
Detected Alarms: None
Asserted/Active Alarms: None
Alarm reporting enabled for: PAIS PRDI PUNEQ PLOP PPLM LOM B3-TCA 

TCA threshold:  B3 = 10e-6
Rx: C2 = 02
Tx: C2 = 02

Tx J1 Length : 64 
Tx J1 Trace

  52 53 50 32 20 30 2F 33 2F 31 34 2E 31 00 00 00     RSP2 0/3/14.1...
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  
Expected J1 Length : 64 
Expected J1 Trace

  52 53 50 32 20 30 2F 33 2F 31 34 2E 31 00 00 00     RSP2 0/3/14.1...
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
          
PATH TRACE BUFFER : UNSTABLE 

Rx J1 Length : 64
Rx J1 Trace

  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  
SONET Path Tables
  INTERVAL       CV    ES   SES   UAS  CVFE  ESFE  SESFE  UASFE
  05:33-05:33     0     0     0     0     0     0      0      0


STS1E 0/3/14.1 PATH  is up.
  Hardware is A900-IMA3G-IMSG

 Applique type is VT1.5

 STS-1 1, VTG 1, VT 1 (STS1E 0/3/14.1/1/1 VT) is up
 No VT alarms detected.
  cep is configured: FALSE cem_id  (0)
  fwd_alarm_ais :0    fwd_alarm_rai :0
  Framing is unframed, Clock Source is Internal
  BIP2-tca:6, BIP2-sf:3, BIP2-sd:6
  Tx V5:1
  Rx V5:2
  Tx J2 Length=64
  TX J2 Trace Buffer:
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  
  Expected J2 Length=64
  Expected J2 Trace Buffer:
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  
  Rx J2 Length=16
  RX J2 Trace Buffer:
  CRC-7: 0x80 OK
          
  4A 44 53 55 00 00 00 00 00 00 00 00 00 00 00 00     JDSU............
  
 Data in curerent interval (1 seconds elapsed)
   Near End
    0 CodeViolations, 0 ErrorSecs, 0 Severly Err Secs, 0 Unavailable Secs
   Far End
    0 CodeViolations, 0 ErrorSecs, 0 Severly Err Secs, 0 Unavailable Secs

 STS-1 1, VTG 1, T1 1 (STS1E 0/3/14.1/1/1 T1) is up
  No alarms detected.
  Framing is unframed, Clock Source is Internal
  Data in current interval (0 seconds elapsed):
   Near End
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
     0 Unavail Secs, 0 Stuffed Secs
   Far End
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
     0 Unavail Secs

The following sample output shows the verification of STS-1e configuration in T3 mode:

router#show controllers sts1e 0/3/14
STS1E 0/3/14 is up.
  Hardware is A900-IMA3G-IMSG

 Port configured rate: OC1
 Applique type is Channelized STS1E
 Clock Source is Internal
Medium info:
  Type: STS1E, Line Coding: NRZ, 
 Alarm Throttling: OFF
 SECTION:
  LOS = 0          LOF = 0                           BIP(B1) = 0

STS1E Section Tables
  INTERVAL       CV    ES   SES  SEFS
  05:35-05:35     0     0     0     0

LINE:
  AIS = 0          RDI = 0          REI = 0          BIP(B2) = 0         
Active Defects: None
Detected Alarms: None
Asserted/Active Alarms: None
Alarm reporting enabled for: SLOS SLOF LAIS SF SD LRDI B1-TCA B2-TCA 
BER thresholds:  SF = 10e-3  SD = 10e-6
TCA thresholds:  B1 = 10e-6  B2 = 10e-6
Rx: S1S0 = 00
    J0 = 00 

    RX S1 = 00

Tx: S1S0 = 00
    J0 = 04

Tx J0 Length : 64
Tx J0 Trace :

  52 53 50 32 20 20 20 20 20 20 20 20 20 20 20 20     RSP2            
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20                     
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20                     
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 00 00                   ..
  
Expected J0 Length : 64
Expected J0 Trace :

  52 53 50 32 20 20 20 20 20 20 20 20 20 20 20 20     RSP2            
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20                     
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20                     
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 00 00                   ..
  
Rx J0 Length : 16
Rx J0 Trace :
  CRC-7: 0xD8 ERROR

  BC 4B 69 CC 79 24 1B 01 E8 EB 9C 36 FC 29 A9 00     .Ki.y$.....6.)..
  
STS1E Line Tables
  INTERVAL       CV    ES   SES   UAS  CVFE  ESFE  SESFE  UASFE
  05:35-05:35     0     0     0    73     0     0      0      0


High Order Path:

PATH 1:
Clock Source is internal

  AIS = 0          RDI = 0          REI = 0          BIP(B3) = 0         
  LOP = 0          PSE = 0          NSE = 0          NEWPTR = 0         
  LOM = 0          PLM = 0          UNEQ = 0         

Active Defects: None
Detected Alarms: None
Asserted/Active Alarms: None
Alarm reporting enabled for: PAIS PRDI PUNEQ PLOP PPLM LOM B3-TCA 

TCA threshold:  B3 = 10e-6
Rx: C2 = 04
Tx: C2 = 04

Tx J1 Length : 64 
Tx J1 Trace

  52 53 50 32 20 30 2F 33 2F 31 34 2E 31 00 00 00     RSP2 0/3/14.1...
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  
Expected J1 Length : 64 
Expected J1 Trace

  52 53 50 32 20 30 2F 33 2F 31 34 2E 31 00 00 00     RSP2 0/3/14.1...
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
          
PATH TRACE BUFFER : UNSTABLE 

Rx J1 Length : 64
Rx J1 Trace

  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  
SONET Path Tables
  INTERVAL       CV    ES   SES   UAS  CVFE  ESFE  SESFE  UASFE
  05:26-05:36     0     0     0    12     0     0      0      0


STS1E 0/3/14.1 T3 is up.
  Hardware is A900-IMA3G-IMSG

  Applique type is T3
  No alarms detected.
  Framing is Unframed, Cablelength is 224
  BER thresholds:  SF = 10e-3  SD = 10e-6
  Clock Source is internal
  Equipment customer loopback
  Data in current interval (560 seconds elapsed):
   Near End
     0 Line Code Violations, 0 P-bit Coding Violation
     0 C-bit Coding Violation, 0 P-bit Err Secs
     0 P-bit Severely Err Secs, 0 Severely Err Framing Secs
     275 Unavailable Secs, 0 Line Errored Secs
     0 C-bit Errored Secs, 0 C-bit Severely Errored Secs
     0 Severely Errored Line Secs, 3 Path Failures
     0 AIS Defect Secs, 0 LOS Defect Secs
   Far End
     0 Errored Secs, 0 Severely Errored Secs
     0 C-bit Unavailable Secs, 0 Path Failures
     0 Code Violations, 0 Service Affecting Secs

The following sample output shows the verification of STS-1e configuration in CT3 mode:

router#show controllers sts1e 0/3/14
STS1E 0/3/14 is up.
  Hardware is A900-IMA3G-IMSG

 Port configured rate: OC1
 Applique type is Channelized STS1E
 Clock Source is Internal
Medium info:
  Type: STS1E, Line Coding: NRZ, 
 Alarm Throttling: OFF
 SECTION:
  LOS = 0          LOF = 0                           BIP(B1) = 0

STS1E Section Tables
  INTERVAL       CV    ES   SES  SEFS
  05:41-05:42     0    10    10    10

LINE:
  AIS = 0          RDI = 0          REI = 0          BIP(B2) = 0         
Active Defects: None
Detected Alarms: None
Asserted/Active Alarms: None
Alarm reporting enabled for: SLOS SLOF LAIS SF SD LRDI B1-TCA B2-TCA 
BER thresholds:  SF = 10e-3  SD = 10e-6
TCA thresholds:  B1 = 10e-6  B2 = 10e-6
Rx: S1S0 = 00
    J0 = 00 

    RX S1 = 00

Tx: S1S0 = 00
    J0 = 04

Tx J0 Length : 64
Tx J0 Trace :

  52 53 50 32 20 20 20 20 20 20 20 20 20 20 20 20     RSP2            
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20                     
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20                     
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 00 00                   ..
  
Expected J0 Length : 64
Expected J0 Trace :

  52 53 50 32 20 20 20 20 20 20 20 20 20 20 20 20     RSP2            
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20                     
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20                     
  20 20 20 20 20 20 20 20 20 20 20 20 20 20 00 00                   ..
  
Rx J0 Length : 16
Rx J0 Trace :
  CRC-7: 0xD8 ERROR

  BC 4B 69 CC 79 24 1B 01 E8 EB 9C 36 FC 29 A9 00     .Ki.y$.....6.)..
  
STS1E Line Tables
  INTERVAL       CV    ES   SES   UAS  CVFE  ESFE  SESFE  UASFE
  05:41-05:42     0     0     0    10     0     0      0      0


High Order Path:

PATH 1:
Clock Source is internal

  AIS = 0          RDI = 0          REI = 0          BIP(B3) = 0         
  LOP = 0          PSE = 0          NSE = 0          NEWPTR = 0         
  LOM = 0          PLM = 0          UNEQ = 0         

Active Defects: None
Detected Alarms: None
Asserted/Active Alarms: None
Alarm reporting enabled for: PAIS PRDI PUNEQ PLOP PPLM LOM B3-TCA 

TCA threshold:  B3 = 10e-6
Rx: C2 = 04
Tx: C2 = 04

Tx J1 Length : 64 
Tx J1 Trace

  52 53 50 32 20 30 2F 33 2F 31 34 2E 31 00 00 00     RSP2 0/3/14.1...
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  
Expected J1 Length : 64 
Expected J1 Trace

  52 53 50 32 20 30 2F 33 2F 31 34 2E 31 00 00 00     RSP2 0/3/14.1...
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
          
PATH TRACE BUFFER : UNSTABLE 

Rx J1 Length : 64
Rx J1 Trace

  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00     ................
  
SONET Path Tables
  INTERVAL       CV    ES   SES   UAS  CVFE  ESFE  SESFE  UASFE
  05:42-05:42     0     0     0     0     0     0      0      0

STS1E 0/3/14.1 T3 is up.
  Hardware is A900-IMA3G-IMSG

  Applique type is Channelized T3 to T1
  No alarms detected.
  MDL transmission is disabled
    
  FEAC code received: No code is being received
  Framing is C-BIT Parity, Cablelength is 224
  BER thresholds:  SF = 10e-3  SD = 10e-6
  Clock Source is internal
  Equipment customer loopback
  Data in current interval (60 seconds elapsed):
   Near End
     0 Line Code Violations, 0 P-bit Coding Violation
     0 C-bit Coding Violation, 0 P-bit Err Secs
     0 P-bit Severely Err Secs, 0 Severely Err Framing Secs
     25 Unavailable Secs, 0 Line Errored Secs
     0 C-bit Errored Secs, 0 C-bit Severely Errored Secs
     0 Severely Errored Line Secs, 0 Path Failures
     0 AIS Defect Secs, 0 LOS Defect Secs
   Far End
     0 Errored Secs, 0 Severely Errored Secs
     0 C-bit Unavailable Secs, 0 Path Failures
     0 Code Violations, 0 Service Affecting Secs

 STS-1 1, T1 1 (STS1E 0/3/14.1/1 T1) is up
  No alarms detected.
  Framing is unframed, Clock Source is Internal
  Data in current interval (60 seconds elapsed):
   Near End
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
     25 Unavail Secs, 0 Stuffed Secs
   Far End
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
     0 Unavail Secs

 STS-1 1, T1 2 (STS1E 0/3/14.1/2 T1) is up
  timeslots: 
  FDL per AT&T 54016 spec.
  No alarms detected.
  Framing is ESF, Clock Source is Internal
  Data in current interval (60 seconds elapsed):
   Near End
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
     26 Unavail Secs, 0 Stuffed Secs
   Far End
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
     0 Unavail Secs

controller sts-1e

To configure a STS-1e controller and enter controller configuration mode, use the controller sts-1e command in global configuration mode.

controller sts-1e slot/ subslot/ port


`slot`	Physical slot number. The slot is always 0.
/`subslot`	Physical sub-slot number. The range for sub-slot is 0-5.
/`port`	STS-1e port number. The range of port number for 3GMS is 12-15 and for 48 T3E3 CE is 0-47.

Command Default

port : 0

Command Modes

Global configuration

Command History


Release	Modification
XE Fuji 16.9.1	This command was integrated into the Cisco ASR 900 Series, Cisco ASR 920 Sesries, and Cisco NCS 4200 Series Routers.

Usage Guidelines

This command can be enabled only after configuring the mode sts1e command under controller mediatype slot/subslot/port command, as shown below:

Router(config)#controller mediaType 0/3/13
Router(config-controller)#mode
Router(config-controller)#mode sts1e

Example

enable
configure terminal
controller sts-1e 0/0/16
sts-1 1
mode sts-1e
t1 1 clock source internal
t1 1 framing unframed
end

mode sts-1e

Use this command to configure the sts-1e mode.

None.

Command Default

None.

Command Modes

Controller configuration.

Command History


Release	Modification
IOS XE Fuji 16.9.1	This command was integrated into the Cisco ASR 900 Series, Cisco ASR 920 Series, and the Cisco NCS 4200 Series.

Usage Guidelines

You can change the mode of a controller only when there are no subinterfaces defined for the controller.

Example

enable
configure terminal
controller MediaType 0/0/16
mode STS-1e
end

Bias-Free Language

Book Title

1 port OC-48/STM-16 or 4 port OC-12/OC-3 / STM-1/STM-4 + 12 port T1/E1 + 4 port T3/E3 CEM Interface Module Configuration Guide, Cisco IOS XE 16 (ASR 920 Series Routers)

Chapter Title

STS-1 Electricals

Results

Chapter: STS-1 Electricals

STS-1 Electricals

Restrictions for STS-1e

Prerequisites for Configuring STS-1e

Configuring MediaType Controller

Configuring STS-1e Modes

Configuring VT-15 Mode of STS-1e

Configuring DS1/T1 CT3 mode of STS-1e

Configuring T3 mode of STS-1e

Configuring Unframed Mode of STS-1e

Configuring Line and Section Overhead

Configuring Line Loopback

Configuring AIS Shut

Configuring Shut

Configuring Clock

Verification of STS-1e Configuration

controller sts-1e

Command Default

Command Modes

Command History

Usage Guidelines

Example

mode sts-1e

Command Default

Command Modes

Command History

Usage Guidelines

Example

Was this Document Helpful?

Contact Cisco