The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.
This guide describes the CLI commands that are used to configure a control plane in cnBNG.
Some keywords and commands are common across multiple commands and configuration modes respectively. Use the information in the Command Modes section only as a reference to navigate to the command in the applicable configuration modes.
Enables RADIUS automated testing.
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius) > Server Configuration (config-server)
auto-test enable Use this command to enable RADIUS automated testing. To disable the RADIUS Automated Testing feature, use the no auto-test enable command.
Enables RADIUS automated testing along with idle-timer functionality.
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius) > Server Configuration (config-server)
auto-test enable idle-timer value Specify the value for idle-timer.
Must be a number in the range of 1 - 30.
Use this command to enable RADIUS automated testing along with idle-timer functionality. To disable the idle-timer functionality, use the no auto-test idle-timer command.
Clears BNG subscriber data.
Exec
clear subscriber [ force ] type { [ ipv4-pool ipv4_pool_name ] [ ipv4-range ipv4_address_range ] [ ipv6-addr-pool ipv6_address_pool_name ] [ ipv6-addr-range ipv6_address_range ] [ ipv6-pfx-pool ipv6_prefix_pool_name ] [ ipv6-pfx-range ipv6_prefix_range ] [ mac mac_address ] [ port-id upf_port_id ] [ sublabel subscriber_label ] [ upf upf_name ] } Specify to force session deletion, even if UP is down.
Specify the IPv4 address pool name.
Must be a string.
Specify the IPv4 address range in the format "poolName /start-ip ".
Must be a string.
Specify the IPv6 address pool name.
Must be a string.
Specify the IPv6 address range in the format "poolName /start-ip ".
Must be a string.
Specify the IPv6 prefix pool name.
Must be a string.
Specify the IPv6 prefix range in the format "poolName /start-pfx ".
Must be a string.
Specify the MAC address in the format "aabb.ccdd.eeff".
Must be a string.
Specify the user plane function port ID in the format "upf /port-id ".
Must be a string.
Specify the subscriber label.
Must be a string.
Specify the user plane function name.
Must be a string.
Specify the type.
Must be one of the following:
dhcp
pppoe
sessmgr
Use this command to clear BNG subscriber data.
Configures endpoint parameters.
Exec > Global Configuration
endpoint endpoint_type { replicas replicas_per_node | nodes node_replicas_for_resiliency | loopbackEth loopbackEth | loopbackPort loopbackPort } Specify the endpoint type.
Specify the endpoint local interface name or host IP.
Must be a string.
Specify the endpoint local port.
Must be an integer.
Specify the number of node replicas for resiliency.
Must be an integer.
Default Value: 1.
Specify the number of replicas per node.
Must be an integer.
Default Value: 1.
In a GR setup for AIO CP cluster, the replica count must be 1 for BGP speaker pod, GR-replication pod, and UDP-proxy pod. For other pods, the replica count should be based on capacity planning.
Use this command to configure endpoint parameters.
Configures the interface type.
Exec > Global Configuration
endpoint ep interface interface_type Specify the loopback Eth.
Must be a string.
Specify the loopback port.
Must be an integer.
Specify the interface type.
Use this command to configure the interface type.
Configures SLA parameters.
Exec > Global Configuration
endpoint ep interface sla { response response_time | procedure procedure_time } Specify the procedure time in milliseconds.
Must be an integer in the range of 1000-120000.
Specify the response time in milliseconds.
Must be an integer in the range of 1000-180000.
Use this command to configure SLA parameters.
Configures VIP IP parameters.
Exec > Global Configuration
endpoint ep interface vip { vip-ip vip_ip | vip-port vip_port | offline } Specify to mark the vip-ip as offline.
Specify the host IP address.
Must be a string.
Specify the port number.
Must be an integer.
Use this command to configure VIP IP parameters.
Configures VIP parameters.
Exec > Global Configuration > Endpoint Confgiuration
vip-ip vip_ip_address [ [ vip-port port_number ] [ offline ] ] Specify the VIP-IP as offline.
Specify the VIP IP address.
Must be a string.
Specify the port number.
Must be an integer.
Use this command to configure VIP parameters.
Configures Helm configuration parameters.
Exec > Global Configuration (config)
helm default-repository default_repository_name Specify the name of the default Helm repository.
Use this command to configure Helm configuration parameters.
Displays Helm release details.
Exec > Global Configuration (config)
charts Use this command to view Helm release details.
Configures Helm repository parameters.
Exec > Global Configuration (config)
helm repository helm_repo_name [ [ access-token access_token ] [ url helm_repo_url ] [ username helm_repo_username ] [ password helm_repo_password ] ] Specify the access token for the Helm repository.
Must be a string.
Specify the password for the Helm repository.
Must be an aes-cfb-128-encrypted string.
Specify the URL for the Helm repository.
Must be a string.
Specify the username for the Helm repostiory.
Must be a string.
Specify the name of the Helm repository.
Must be a string.
Use this command to configure the Helm repository parameters.
Configures IPAM address pools.
Exec > Global Configuration (config) > IPAM Configuration (config-ipam)
address-pool pool_name [ static | offline | vrf-name vrf_name ] Specify the address quarantine timer interval in seconds.
Must be an integer in the range of 4-60.
Default Value: 4.
Specify the default gateway IP address for static pool.
Must be an IPv4 address.
Specify the pool as an offline pool.
Specify the prefix length.
Must be an integer in the range of 1-64.
Default Value: 64.
Specify the VRF name.
Must be a string.
Specify the address pool's name.
Must be a string.
Use this command to configure IPAM address pools.
Configures IPv4 address ranges.
Exec > Global Configuration (config) > IPAM Configuration (config-ipam) > Address Pool Configuration
address-range start_ipv4_address end_ipv4_address [ offline ] Specify the default gateway IP address for static pool.
Must be an IPv4 address.
Specify the IPv4 address range as offline.
Specify the end address of the IPv4 address range.
Must be an IPv4 address.
Specify the start address of the IPv4 address range.
Must be an IPv4 address.
Use this command to configure IPv4 address ranges.
Configures chunk split size.
Exec > Global Configuration > IPAM Configuration
split-size [ per-cache number_of_addresses ] [ per-dp number_of_addresses ] Specify not to split the address range into smaller chunks.
Specify the number of addresses per chunk for IPAM cache allocation. Specify in power of 2.
Must be an integer in the range of 2-262144.
Specify the number of addresses per chunk for data-plane allocation. Specify in power of 2.
Must be an integer in the range of 2-262144.
Use this command to configure chunk split sizes.
Configures pool thresholds.
Exec > Global Configuration > IPAM Configuration
threshold upper-threshold upper_threshold Specify the upper threshold value in percentage.
Must be an integer in the range of 1-100.
Use this command to configure pool thresholds.
Configures IPv6 address ranges.
Exec > Global Configuration (config) > IPAM Configuration (config-ipam) > Address Pool Configuration > Address Ranges Configuration
address-range start_ipv6_address end_ipv6_address [ offline ] Specify the default gateway IP address for static pool.
Must be an IPv4 address.
Specify the IPv6 address range as offline.
Specify the end address of the IPv6 address range.
Must be an IPv6 address.
Specify the start address of the IPv6 address range.
Must be an IPv6 address.
Use this command to configure IPv6 address ranges.
Configures chunk split size.
Exec > Global Configuration > IPAM Configuration
split-size [ per-cache number_of_addresses ] [ per-dp number_of_addresses ] Specify not to split the address range into smaller chunks.
Specify the number of addresses per chunk for IPAM cache allocation. Specify in power of 2.
Must be an integer in the range of 2-262144.
Specify the number of addresses per chunk for data-plane allocation. Specify in power of 2.
Must be an integer in the range of 2-262144.
Use this command to configure chunk split sizes.
Configures pool thresholds.
Exec > Global Configuration > IPAM Configuration
threshold upper-threshold upper_threshold Specify the upper threshold value in percentage.
Must be an integer in the range of 1-100.
Use this command to configure pool thresholds.
Configures IPv6 prefix ranges.
Exec > Global Configuration (config) > IPAM Configuration (config-ipam) > Address Pool Configuration > Prefix Ranges Configuration
prefix-range prefix_value length prefix_length [ offline ] Specify the prefix length.
Must be an integer in the range of 1-63.
Specify the IPv6 prefix range as offline.
Specify the IPv6 prefix range.
Must be an IPv6 address.
Use this command to configure IPv6 prefix ranges.
Configures chunk split size.
Exec > Global Configuration > IPAM Configuration
split-size [ per-cache number_of_addresses ] [ per-dp number_of_addresses ] Specify not to split the address range into smaller chunks.
Specify the number of addresses per chunk for IPAM cache allocation. Specify in power of 2.
Must be an integer in the range of 2-262144.
Specify the number of addresses per chunk for data-plane allocation. Specify in power of 2.
Must be an integer in the range of 2-262144.
Use this command to configure chunk split sizes.
Configures pool thresholds.
Exec > Global Configuration > IPAM Configuration
threshold upper-threshold upper_threshold Specify the upper threshold value in percentage.
Must be an integer in the range of 1-100.
Use this command to configure pool thresholds.
Configures static pool parameters.
Exec > Global Configuration (config) > IPAM Configuration (config-ipam) > Address Pool Configuration
static { enable | user-plane user_plane } Specify to set pool as static.
Specify to associate user plane for this static pool.
Must be a string.
Use this command to configure static pool parameters.
Configures pool-datastore source selection.
Exec > Global Configuration (config)
ipam source local Specify to use local address pool datastore.
Use this command to configure pool-datastore source selection. Enters the IPAM Configuration mode";
Configures global thresholds.
Exec > Global Configuration (config) > IPAM Configuration (config-ipam)
threshold [ [ ipv4-addr ipv4_address_threshold ] | [ ipv6-addr ipv6_address_threshold ] | [ ipv6-prefix ipv6_prefix_threshold ] ] Specify the IPv4 address threshold in percentage.
Must be an integer in the range of 1-100.
Specify the IPv6 address threshold in percentage.
Must be an integer in the range of 1-100.
Specify the IPv6 prefix threshold in percentage.
Must be an integer in the range of 1-100.
Use this command to configure global thresholds.
Configures k8 BNG parameters.
Exec > Global Configuration
bng etcd-endpoint etcd_endpoint datastore-endpoint datastore_endpoint coverage-build { false | true } Specify the Etcd endpoint configuration. For example, hostname :port
Default Value: "etcd:2379".
Specify the Datastore endpoint configuration. For example, hostname :port
Specify the Etcd endpoint configuration. For example, hostname :port
Default Value: "datastore-ep-session:8882".
Specify to enable or disable coverage build.
Must be one of the following:
false
true
Default Value: false.
Specify the Datastore endpoint configuration. For example, hostname :port
Specify the Etcd endpoint configuration. For example, hostname :port
Use this command to configure k8 BNG parameters.
Configures K8 node affinity label pod group configuration.
Exec > Global Configuration
k8 label pod-group-config pod-group pod_group key label_key value label_value Specify the key for the label.
Must be a string.
Specify the pod group for the VMs.
Must be one of the following:
cdl-layer
oam-layer
protocol-layer
service-layer
Specify the value for the label.
Must be a string.
Use this command to configure K8 node affinity label pod group configuration.
Configures Kubernetes parameters.
Exec > Global Configuration (config)
k8s name k8s_cluster_name [ [ image-pull-secrets image_pull_secrets ] [ ingress-host-name ingress_host_name ] [ namespace k8s_namespace ] [ nf-name nf_name ] [ registry image_registry ] [ single-node { false | true } ] [ use-volume-claims { false | true } ] ] Specify the image pull secrets stored within K8s.
Must be a string.
Specify the generic ingress host name.
Must be a string.
Specify the K8s cluster name.
Must be a string.
Specify the K8s namespace for the network function.
Must be a string.
Specify the NF deployed in this k8s namespace.
Must be a string.
This keyword is deprecated.
Must be a string.
Specify to enable or disable single node deployment.
Must be one of the following:
false
true
Default Value: false.
Specify to enable or disable using volume claims when deploying.
Must be one of the following:
false
true
Default Value: false.
Use this command to configure Kubernetes parameters.
Configures list of k8s nodes.
Exec > Global Configuration (config)
k8s nodes k8s_node_name [ [ node-type node_type ] [ worker-type worker_type ] ] Specify the K8s node type.
Must be a string.
Specify the k8s worker type.
Must be a string.
Specify the K8s node name.
Must be a string.
Use this command to configure the list of k8s nodes.
Configures the logging level.
Exec > Global Configuration
level log_level Specify the application logging level.
Must be one of the following:
debug
error
info
off
trace
warn
Specify the monitor subscriber logging level.
Must be one of the following:
debug
error
info
off
trace
warn
Specify the tracing logging level.
Must be one of the following:
debug
error
info
off
trace
warn
Specify the transaction logging level.
Must be one of the following:
debug
error
info
off
trace
warn
Use this command to configure the logging level.
Configures the log name.
Exec > Global Configuration
logger log_name Specify the log name in "module.component.interface" format.
Must be a string.
Use this command to configure the log name.
Configures the logging level.
Exec > Global Configuration
logger level log_type_options Specify the application logging level.
Must be one of the following:
debug
error
info
off
trace
warn
Specify the monitor subscriber logging level.
Must be one of the following:
debug
error
info
off
trace
warn
Specify the tracing logging level.
Must be one of the following:
debug
error
info
off
trace
warn
Specify the transaction logging level.
Must be one of the following:
debug
error
info
off
trace
warn
Use this command to configure the logging level.
Configures the transaction logging parameters.
Exec > Global Configuration
transaction transaction_log_parameters Specify to enable duplicate in transaction logging.
Must be one of the following:
disable
enable
Default Value: disable.
Specify to enable messages in transaction logging.
Must be one of the following:
disable
enable
Default Value: disable.
Use this command to configure the transaction logging parameters.
Enables the cnBNG to prepend the AS-path attribute to BGP Virtual IP (VIP) routes when advertising to neighboring routers.
Exec > Global Configuration (config) > Router BGP Configuration (config-bgp)
prepend as-path true Use this command to enable prepending of AS-path attribute to BGP VIP routes.
Configures AAA profiles.
Exec > Global Configuration (config)
profile aaa aaa_profile_name Specify the AAA profile name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Use this command to configure AAA profiles. Enters the AAA Profile Configuration mode.
Configures accounting configuration parameters.
Exec > Global Configuration (config) > AAA Profile Configuration (config-aaa-aaa_profile_name )
accounting method-order method_list_order Specify the method list order.
Must be one of the following:
radius
Use this command to configure accounting parameters.
You can configure a maximum of three elements with this command.
Configures asynchronous mode for service accounting.
Exec > Global Configuration (config) > AAA Profile Configuration (config-aaa-aaa_profile_name ) >Accounting configuration (config-accounting)
service { acct-interim-async true/false | acct-start-async true/false | acct-stop-async true/false } Specifies the option to enable or disable the asynchronous mode when interim updates are sent.
Must be one of the following:
true
false
Specifies the option to enable or disable the asynchronous mode when an Accounting-Start request is sent to AAA.
Must be one of the following:
true
false
Specifies the option to enable or disable the asynchronous mode when an Accounting-Stop request is sent.
Must be one of the following:
true
false
Use this command to configure asynchronous mode for service accounting.
If asynchronous RADIUS accounting is configured, message retransmission functionality will be unavailable. Lost messages due to network issues or server errors will not be retried by the Control Plane.
Configures asynchronous mode for session accounting.
Exec > Global Configuration (config) > AAA Profile Configuration (config-aaa-aaa_profile_name ) >Accounting configuration (config-accounting)
session { acct-interim-async true/false | acct-start-async true/false | acct-stop-async true/false } Specifies the option to enable or disable the asynchronous mode when interim updates are sent.
Must be one of the following:
true
false
Specifies the option to enable or disable the asynchronous mode when an Accounting-Start request is sent to AAA.
Must be one of the following:
true
false
Specifies the option to enable or disable the asynchronous mode when an Accounting-Stop request is sent.
Must be one of the following:
true
false
Use this command to configure asynchronous mode for session accounting.
If asynchronous RADIUS accounting is configured, message retransmission functionality will be unavailable. Lost messages due to network issues or server errors will not be retried by the Control Plane.
Configures authentication parameters.
Exec > Global Configuration (config) > AAA Profile Configuration (config-aaa-aaa_profile_name )
authentication [ method-order method_list_order ] Specify the method list order.
Must be one of the following:
radius
Use this command to configure authentication parameters.
You can configure a maximum of three elements with this command.
Configures authorization parameters.
Exec > Global Configuration (config) > AAA Profile Configuration (config-aaa-aaa_profile_name )
authorization [ password default_password ] Specify the default password.
Must be a string.
Use this command to configure authorization parameters. Enters the Authorization Configuration mode.
Configures authorization type subscriber.
Exec > Global Configuration (config) > AAA Profile Configuration (config-aaa-aaa_profile_name ) > Authorization Configuration (config-authorization)
type subscriber method-order method_list_order Specify the method list order.
Must be one of the following:
radius
Use this command to configure authorization type subscriber.
You can configure a maximum of three elements with this command.
Configures the default user name.
Exec > Global Configuration (config) > AAA Profile Configuration (config-aaa-aaa_profile_name ) > Authorization Configuration (config-authorization)
username { format attribute_format | identifier identifier_type | value user_name } Specify the attribute format.
Specify the identifier type.
Specify the user name.
Must be a string.
Use this command to configure the default user name.
Configures AAA attribute templates.
Exec > Global Configuration (config)
profile attribute-format profile_name [ format-order attributes_list ] Specify the ordered list of attributes.
Specify the profile name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Must be a string.
Use this command to configure AAA attribute templates. Enters the Attribute Format Profile Configuration mode.
You can configure a maximum of 32 elements with this command.
Configures RADIUS Dynamic-author/COA parameters.
Exec > Global Configuration
profile coa server-key server_shared_secret_key Specify the COA server shared secret key.
Must be an aes-cfb-128-encrypted string.
Use this command to configure RADIUS Dynamic-author/COA parameters.
Configures RADIUS COA client parameters.
Exec > Global Configuration
client ip client_ip_address server-key client_shared_secret_key Specify the client IP address.
Must be an IP address.
Specify the client shared secret key.
Must be an aes-cfb-128-encrypted string.
Use this command to configure RADIUS COA client parameters.
Configures DHCP profiles.
Exec > Global Configuration (config)
dhcp dhcp_profile_name Specify the DHCP profile name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Use this command to configure DHCP profiles. Enters the DHCP Profile Configuration mode.
Configures DHCP IPv4 parameters.
Exec > Global Configuration (config) > DHCP Profile Configuration (config-dhcp-dhcp_profile_name )
ipv4 [ mode dhcp_mode ] Specify the DHCP server or proxy mode.
Default Value: server.
Use this command to configure DHCP IPv4 parameters. Enters the DHCP IPv4 Configuration mode.
Configures DHCP IPv4 class configuration parameters.
Exec > Global Configuration (config) > DHCP Profile Configuration (config-dhcp-dhcp_profile_name ) > DHCP IPv4 Configuration (config-ipv4)
class dhcp_class_name Specify the DHCP class name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Use this command to configure DHCP IPv4 class configuration parameters. Enters the DHCP Class Configuration mode.
Configures the list of match values.
Exec > Global Configuration (config) > DHCP Profile Configuration (config-dhcp-dhcp_profile_name ) > DHCP IPv4 Configuration (config-ipv4) > DHCP Class Configuration (config-class-dhcp_class_name )
matches [ match-type { all | any } ] Specify the match type.
Use this command to configure the list of match values. Enters the Matches Configuration mode.
Configures match key and value.
Exec > Global Configuration (config) > DHCP Configuration (config-dhcp-dhcp_profile_name ) > DHCP Class Configuration (config-class-dhcp_class_name ) > Matches Configuration (config-matches)
match match_key { ascii ascii_string | hex hex_string } Specify the match key.
Specify the ASCII strings.
Must be a string.
Specify the hexadecimal strings.
Must be a string in the pattern ([0-9a-fA-F]{2}([0-9a-fA-F]{2})*)?.
Specify the match key.
You can configure a maximum of "8" elements with this command.
Use this command to configure match key and value.
You can configure a maximum of "8" elements with this command.
Configures DHCP server mode.
Exec > Global Configuration (config) > DHCP Profile Configuration (config-dhcp-dhcp_profile_name ) > DHCP IPv4 Configuration (config-ipv4)
Exec > Global Configuration (config) > DHCP Profile Configuration (config-dhcp-dhcp_profile_name ) > DHCP IPv4 Configuration (config-ipv4) > DHCP Class Configuration (config-class-dhcp_class_name )
server [ boot-filename boot_file_name | dns-servers ip_address | domain-name domain_name | netbios-name-server ip_address | next-server ip_address | ntp-servers ntp_servers | pool-name pool_name ] Specify the boot file name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Specify the DNS server IP addresses.
Must be an IPv4 address.
Specify the domain name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Specify the NetBIOS name server IP addresses.
Must be an IPv4 address.
Specify the TFTP server IP address to be used by the client.
Must be an IPv4 address.
Specify the NTP servers.
Must be an IPv4 address.
Specify the pool name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Use this command to configure the DHCP server mode. Enters the DHCP Server Configuration mode.
You can configure a maximum of "8" elements with this command.
Configures DHCP Server Lease parameters.
Exec > Global Configuration (config) > DHCP Profile Configuration (config-dhcp-dhcp_profile_name ) > DHCP IPv4 Configuration (config-ipv4) > DHCP Server Configuration Mode (config-server)
Exec > Global Configuration (config) > DHCP Profile Configuration (config-dhcp-dhcp_profile_name ) > DHCP IPv4 Configuration (config-ipv4) > DHCP Class Configuration (config-class-dhcp_class_name ) > DHCP Server Configuration Mode (config-server)
lease { [ days days ] [ hours hours ] [ minutes minutes ] } Specify the number of days.
Must be an integer in the range of 0-365.
Specify the hours.
Must be an integer in the range of 0-23.
Specify the minutes.
Must be an integer in the range of 0-59.
Use this command to configure the DHCP Server Lease parameters.
Configures NetBIOS node type.
Exec > Global Configuration (config) > DHCP Profile Configuration (config-dhcp-dhcp_profile_name ) > DHCP IPv4 Configuration (config-ipv4) > DHCP Server Configuration Mode (config-server)
Exec > Global Configuration (config) > DHCP Profile Configuration (config-dhcp-dhcp_profile_name ) > DHCP IPv4 Configuration (config-ipv4) > DHCP Class Configuration (config-class-dhcp_class_name ) > DHCP Server Configuration Mode (config-server)
netbios-node-type { broadcast-node | hexadecimal hex_number | hybrid-node | mixed-node | peer-to-peer-node } Specify broadcast node.
Specify the hexadecimal number.
Must be a string in the pattern ([0-9a-fA-F]{2}(:[0-9a-fA-F]{2})*)?.
Specify hybrid node.
Specify mixed node.
Specify peer-to-peer node.
Use this command to configure the NetBIOS node type.
Configures the OptionCode table.
Exec > Global Configuration (config) > DHCP Profile Configuration (config-dhcp-dhcp_profile_name ) > DHCP IPv4 Configuration (config-ipv4) > DHCP Server Configuration Mode (config-server)
Exec > Global Configuration (config) > DHCP Profile Configuration (config-dhcp-dhcp_profile_name ) > DHCP IPv4 Configuration (config-ipv4) > DHCP Class Configuration (config-class-dhcp_class_name ) > DHCP Server Configuration Mode (config-server)
option-codes Use this command to configure the OptionCode table. Enters the Option Codes Configuration mode.
Configures a DHCP option code.
Exec > Global Configuration (config) > DHCP Profile Configuration (config-dhcp-dhcp_profile_name ) > DHCP IPv4 Configuration (config-ipv4) > DHCP Server Configuration Mode (config-server) > Option Codes Configuration (config-option-codes)
Exec > Global Configuration (config) > DHCP Profile Configuration (config-dhcp-dhcp_profile_name ) > DHCP IPv4 Configuration (config-ipv4) > DHCP Class Configuration (config-class-dhcp_class_name ) > DHCP Server Configuration Mode (config-server) > Option Codes Configuration (config-option-codes)
option-code dhcp_option_code [ ascii-string ascii_string | force-insert { false | true } | hex-string hex_string | ip-address ip_address ] Specify the ASCII string.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Specify whether to force insert this option.
Must be one of the following:
false
true
Specify the hexadecimal string.
Must be a string in the pattern ([0-9a-fA-F]{2}([0-9a-fA-F]{2})*)?.
Specify the server's IP addresses.
Must be an IPv4 address.
Specify the DHCP option code.
Must be an integer in the range of 0-255.
Use this command to configure a DHCP option code. Enters the Option Code Configuration mode.
You can configure a maximum of "8" elements with this command.
Configures DHCP server mode.
Exec > Global Configuration (config) > DHCP Profile Configuration (config-dhcp-dhcp_profile_name ) > DHCP IPv4 Configuration (config-ipv4)
Exec > Global Configuration (config) > DHCP Profile Configuration (config-dhcp-dhcp_profile_name ) > DHCP IPv4 Configuration (config-ipv4) > DHCP Class Configuration (config-class-dhcp_class_name )
server [ boot-filename boot_file_name | dns-servers ip_address | domain-name domain_name | netbios-name-server ip_address | next-server ip_address | ntp-servers ntp_servers | pool-name pool_name ] Specify the boot file name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Specify the DNS server IP addresses.
Must be an IPv4 address.
Specify the domain name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Specify the NetBIOS name server IP addresses.
Must be an IPv4 address.
Specify the TFTP server IP address to be used by the client.
Must be an IPv4 address.
Specify the NTP servers.
Must be an IPv4 address.
Specify the pool name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Use this command to configure the DHCP server mode. Enters the DHCP Server Configuration mode.
You can configure a maximum of "8" elements with this command.
Configures DHCP Server Lease parameters.
Exec > Global Configuration (config) > DHCP Profile Configuration (config-dhcp-dhcp_profile_name ) > DHCP IPv4 Configuration (config-ipv4) > DHCP Server Configuration Mode (config-server)
Exec > Global Configuration (config) > DHCP Profile Configuration (config-dhcp-dhcp_profile_name ) > DHCP IPv4 Configuration (config-ipv4) > DHCP Class Configuration (config-class-dhcp_class_name ) > DHCP Server Configuration Mode (config-server)
lease { [ days days ] [ hours hours ] [ minutes minutes ] } Specify the number of days.
Must be an integer in the range of 0-365.
Specify the hours.
Must be an integer in the range of 0-23.
Specify the minutes.
Must be an integer in the range of 0-59.
Use this command to configure the DHCP Server Lease parameters.
Configures NetBIOS node type.
Exec > Global Configuration (config) > DHCP Profile Configuration (config-dhcp-dhcp_profile_name ) > DHCP IPv4 Configuration (config-ipv4) > DHCP Server Configuration Mode (config-server)
Exec > Global Configuration (config) > DHCP Profile Configuration (config-dhcp-dhcp_profile_name ) > DHCP IPv4 Configuration (config-ipv4) > DHCP Class Configuration (config-class-dhcp_class_name ) > DHCP Server Configuration Mode (config-server)
netbios-node-type { broadcast-node | hexadecimal hex_number | hybrid-node | mixed-node | peer-to-peer-node } Specify broadcast node.
Specify the hexadecimal number.
Must be a string in the pattern ([0-9a-fA-F]{2}(:[0-9a-fA-F]{2})*)?.
Specify hybrid node.
Specify mixed node.
Specify peer-to-peer node.
Use this command to configure the NetBIOS node type.
Configures the OptionCode table.
Exec > Global Configuration (config) > DHCP Profile Configuration (config-dhcp-dhcp_profile_name ) > DHCP IPv4 Configuration (config-ipv4) > DHCP Server Configuration Mode (config-server)
Exec > Global Configuration (config) > DHCP Profile Configuration (config-dhcp-dhcp_profile_name ) > DHCP IPv4 Configuration (config-ipv4) > DHCP Class Configuration (config-class-dhcp_class_name ) > DHCP Server Configuration Mode (config-server)
option-codes Use this command to configure the OptionCode table. Enters the Option Codes Configuration mode.
Configures a DHCP option code.
Exec > Global Configuration (config) > DHCP Profile Configuration (config-dhcp-dhcp_profile_name ) > DHCP IPv4 Configuration (config-ipv4) > DHCP Server Configuration Mode (config-server) > Option Codes Configuration (config-option-codes)
Exec > Global Configuration (config) > DHCP Profile Configuration (config-dhcp-dhcp_profile_name ) > DHCP IPv4 Configuration (config-ipv4) > DHCP Class Configuration (config-class-dhcp_class_name ) > DHCP Server Configuration Mode (config-server) > Option Codes Configuration (config-option-codes)
option-code dhcp_option_code [ ascii-string ascii_string | force-insert { false | true } | hex-string hex_string | ip-address ip_address ] Specify the ASCII string.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Specify whether to force insert this option.
Must be one of the following:
false
true
Specify the hexadecimal string.
Must be a string in the pattern ([0-9a-fA-F]{2}([0-9a-fA-F]{2})*)?.
Specify the server's IP addresses.
Must be an IPv4 address.
Specify the DHCP option code.
Must be an integer in the range of 0-255.
Use this command to configure a DHCP option code. Enters the Option Code Configuration mode.
You can configure a maximum of "8" elements with this command.
Configures DHCP IPv6 parameters.
Exec > Global Configuration (config) > DHCP Profile Configuration (config-dhcp-dhcp_profile_name )
ipv6 [ mode dhcp_mode ] Specify the DCHP mode server or proxy.
Default Value: server.
Use this command to configure DHCP IPv6 parameters. Enters the DHCP IPv6 Configuration mode.
Configures DHCP IPv6 class configuration parameters.
Exec > Global Configuration (config) > DHCP Profile Configuration (config-dhcp-dhcp_profile_name ) > DHCP IPv6 Configuration (config-ipv6)
class dhcp_class_name Specify the DHCP class name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Use this command to configure DHCP IPv6 class configuration parameters.
Configures DHCP server mode.
Exec > Global Configuration (config) > DHCP Profile Configuration (config-dhcp-dhcp_profile_name ) > DHCP IPv6 Configuration (config-ipv6)
Exec > Global Configuration (config) > DHCP Profile Configuration (config-dhcp-dhcp_profile_name ) > DHCP IPv6 Configuration (config-ipv6) > DHCP Class Configuration (config-class-dhcp_class_name )
server { aftr-name aftr_name | dns-servers ip_address | domain-name domain_name | iana-pool-name iana_pool_name | iapd-pool-name iapd_pool_name | preference server_preference | rapid-commit } Specify the Address Family Transition Router (AFTR) name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Specify the DNS server IP addresses.
Must be an IPv6 address.
Specify the domain name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Specify the IANA pool name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Specify the IAPD pool name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Specify the DHCP server preference.
Must be an integer in the range of 1-255.
Specify to allow rapid commit.
Use this command to configure the DHCP server mode.
You can configure a maximum of "8" elements with this command.
Configures the lease parameters.
Exec > Global Configuration (config) > DHCP Profile Configuration (config-dhcp-dhcp_profile_name ) > DHCP IPv6 Configuration (config-ipv6) > DHCP Server Configuration Mode (config-server)
Exec > Global Configuration (config) > DHCP Profile Configuration (config-dhcp-dhcp_profile_name ) > DHCP IPv6 Configuration (config-ipv6) > DHCP Class Configuration (config-class-dhcp_class_name ) > DHCP Server Configuration Mode (config-server)
lease { [ days days ] [ hours hours ] [ minutes minutes ] } Specify the number of days.
Must be an integer in the range of 0-365.
Specify the hours.
Must be an integer in the range of 0-23.
Specify the minutes.
Must be an integer in the range of 1-59.
Use this command to configure lease parameters.
Configures DHCP server mode.
Exec > Global Configuration (config) > DHCP Profile Configuration (config-dhcp-dhcp_profile_name ) > DHCP IPv6 Configuration (config-ipv6)
Exec > Global Configuration (config) > DHCP Profile Configuration (config-dhcp-dhcp_profile_name ) > DHCP IPv6 Configuration (config-ipv6) > DHCP Class Configuration (config-class-dhcp_class_name )
server { aftr-name aftr_name | dns-servers ip_address | domain-name domain_name | iana-pool-name iana_pool_name | iapd-pool-name iapd_pool_name | preference server_preference | rapid-commit } Specify the Address Family Transition Router (AFTR) name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Specify the DNS server IP addresses.
Must be an IPv6 address.
Specify the domain name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Specify the IANA pool name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Specify the IAPD pool name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Specify the DHCP server preference.
Must be an integer in the range of 1-255.
Specify to allow rapid commit.
Use this command to configure the DHCP server mode.
You can configure a maximum of "8" elements with this command.
Configures the lease parameters.
Exec > Global Configuration (config) > DHCP Profile Configuration (config-dhcp-dhcp_profile_name ) > DHCP IPv6 Configuration (config-ipv6) > DHCP Server Configuration Mode (config-server)
Exec > Global Configuration (config) > DHCP Profile Configuration (config-dhcp-dhcp_profile_name ) > DHCP IPv6 Configuration (config-ipv6) > DHCP Class Configuration (config-class-dhcp_class_name ) > DHCP Server Configuration Mode (config-server)
lease { [ days days ] [ hours hours ] [ minutes minutes ] } Specify the number of days.
Must be an integer in the range of 0-365.
Specify the hours.
Must be an integer in the range of 0-23.
Specify the minutes.
Must be an integer in the range of 1-59.
Use this command to configure lease parameters.
Configures feature templates.
Exec > Global Configuration (config)
feature-template feature_template_name [ [ vrf-name vrf_name ] [ httpr-policy httpr_policy_name ] ] Specify the PBR HTTPR policy name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Specify the VRF name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Specify the feature template name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Use this command to configure feature templates. Enters the Feature Template Configuration mode.
Configures IPv4 features.
Exec > Global Configuration (config) > Feature Template Profile Configuration (config-feature-template-feature_template_name )
ipv4 [ [ mtu maximum_transmission_unit ] [ ingress-acl ingress_ipv4_acl_name ] [ egress-acl egress_ipv4_acl_name ] [ disable-unreachables ] ] Specify to disable sending ICMP Unreachable messages.
Specify the egress IPV4 ACL name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Specify the ingress IPV4 ACL name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Specify the Maximum Transmission Unit in bytes.
Must be an integer in the range of 68-65535.
Use this command to configure IPv4 features. Enters the IPv4 Configuration mode.
Enables per-packet validation for unicast.
Exec > Global Configuration (config) > Feature Template Profile Configuration (config-feature-template-feature_template_name ) > IPv4 Configuration (config-ipv4)
verify-unicast-source reachable-via-rx Specify the source is reachable via interface on which packet was received.
Use this command to enable per-packet validation for unicast.
Configures IPv6 features.
Exec > Global Configuration (config) > Feature Template Profile Configuration (config-feature-template-feature_template_name )
ipv6 [ [ mtu maximum_transmission_unit ] [ ingress-acl ingress_ipv6_acl_name ] [ egress-acl egress_ipv6_acl_name ] ] Specify to disable sending ICMP Unreachable messages.
Specify the egress IPV6 ACL name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Specify the ingress IPV6 ACL name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Specify the Maximum Transmission Unit in bytes.
Must be an integer in the range of 1280-65535.
Use this command to configure IPv6 features. Enters the IPv6 Configuration mode.
Configures per packet validation for unicast.
Exec > Global Configuration (config) > Feature Template Profile Configuration (config-feature-template-feature_template_name ) > IPv6 Configuration (config-ipv6)
verify-unicast-source reachable-via-rx Specify source is reachable via interface on which packet was received.
Use this command to configure per packet validation for unicast.
Configures PPP feature.
Exec > Global Configuration (config) > Feature Template Profile Configuration (config-feature-template-feature_template_name )
ppp [ [ authentication authentication_method ] [ max-bad-auth max_auth_failures ] [ max-configure max_configure ] [ max-failure max_conf_naks ] ] Specify the authentication method.
Must be one of the following:
chap
pap
Specify the maximum authentication failures to allow.
Must be an integer in the range of 0-10.
Specify the maximum conf-reqs to send without response.
Must be an integer in the range of 1-10.
Specify the maximum conf-naks to receive.
Must be an integer in the range of 1-5.
Use this command to configure the PPP feature. Enters the PPP Configuration mode.
You can configure a maximum of "2" elements with this command.
Configures Challenge Handshake Authentication Protocol (CHAP) parameters.
Exec > Global Configuration (config) > Feature Template Profile Configuration (config-feature-template-feature_template_name ) > PPP Configuration (config-ppp)
chap hostname chap_host_name [ password chap_password ] Specify the CHAP host name.
Specify the CHAP host name.
Specify the CHAP password.
Must be an aes-cfb-128-encrypted string.
Use this command to configure CHAP parameters.
Configures PPP IPCP negotiation parameters.
Exec > Global Configuration (config) > Feature Template Profile Configuration (config-feature-template-feature_template_name ) > PPP Configuration (config-ppp)
ipcp peer-address-pool peer_address_pool_name Specify the peer-address pool name.
Use this command to configure PPP IPCP negotiation parameters.
Configures DNS address to be used for peer.
Exec > Global Configuration (config) > Feature Template Profile Configuration (config-feature-template-feature_template_name ) > PPP Configuration (config-ppp)
ipcp dns primary-address primary_address secondary-address secondary_address Specify the primary address. The first address is considered as Primary and second address as Secondary.
Must be an IPv4 address.
Specify the secondary address.
Must be an IPv4 address.
Use this command to configure DNS address to be used for peer.
Configures renegotiation parameters.
Exec > Global Configuration (config) > Feature Template Profile Configuration (config-feature-template-feature_template_name ) > PPP Configuration (config-ppp)
ipcp renegotiation ignore Specify to ignore attempts by the peer to renegotiate LCP.
Use this command to configure renegotiation parameters.
Configures WINS address to be used for peer.
Exec > Global Configuration (config) > Feature Template Profile Configuration (config-feature-template-feature_template_name ) > PPP Configuration (config-ppp)
ipcp wins primary-address primary_ip_address secondary-address secondary_ip_address Specify the primary address.
Must be an IPv4 address.
Specify the secondary address.
Must be an IPv4 address.
Use this command to configure WINS address to be used for peer.
Configures IPv6CP renegotiation parameters.
Exec > Global Configuration (config) > Feature Template Profile Configuration (config-feature-template-feature_template_name ) > PPP Configuration (config-ppp)
ipv6cp renegotiation ignore Specify to ignore attempts by the peer to renegotiate LCP.
Use this command to configure IPv6CP renegotiation parameters.
Configures PPP Keepalive parameters.
Exec > Global Configuration (config) > Feature Template Profile Configuration (config-feature-template-feature_template_name ) > PPP Configuration (config-ppp)
keepalive { disable | interval keepalive_interval | retry keepalive_retries } Specify to disable PPP keepalive.
Specify the keepalive interval in minutes.
Must be an integer in the range of 10-120.
Specify the number of keepalive retries.
Must be an integer in the range of 1-255.
Use this command to configure PPP Keepalive parameters.
Configures the time to delay before starting active LCP negotiations.
Exec > Global Configuration (config) > Feature Template Profile Configuration (config-feature-template-feature_template_name ) > PPP Configuration (config-ppp)
lcp delay seconds delay_value milliseconds delay_value Specify the delay value in milliseconds.
Must be an integer in the range of 0-70000000.
Specify the delay value in seconds.
Must be an integer in the range of 0-255.
Use this command to configure the time to delay before starting active LCP negotiations.
Configures LCP renegotiation feature.
Exec > Global Configuration (config) > Feature Template Profile Configuration (config-feature-template-feature_template_name ) > PPP Configuration (config-ppp)
lcp renegotiation ignore Specify to ignore attempts by the peer to renegotiate LCP.
Use this command to configure LCP renegotiation feature.
Configures PAP parameters.
Exec > Global Configuration (config) > Feature Template Profile Configuration (config-feature-template-feature_template_name ) > PPP Configuration (config-ppp)
pap accept-null-password Specify to accept null-password option.
Use this command to configure PAP parameters.
Configures PPP timeout parameters.
Exec > Global Configuration (config) > Feature Template Profile Configuration (config-feature-template-feature_template_name ) > PPP Configuration (config-ppp)
timeout { [ authentication total_auth_complete_time ] [ retry max_response_time ] } Exec > Global Configuration (config) > Endpoint N4 Protocol Configuration (config-endpoint-n4-protocol)
retransmission timeout total_auth_complete_time [ retry max_response_time ] Specify the total time to allow for authentication to complete.
Must be an integer in the range of 3-30.
Specify the maximum time to wait for a response to a Conf-Req in seconds.
Must be an integer in the range of 1-10.
Use this command to configure PPP timeout parameters.
Configures the absolute timeout period for a PPP session.
Exec > Global Configuration (config) > Feature Template Profile Configuration (config-feature-template-feature_template_name ) > PPP Configuration (config-ppp)
timeout absolute minutes timeout_minutes seconds timeout_seconds Specify the timeout period in minutes.
Must be an integer in the range of 0-70000000.
Use this command to configure the absolute timeout period for a PPP session.
Configures QoS input policy parameters.
Exec > Global Configuration (config) > Feature Template Profile Configuration (config-feature-template-feature_template_name )
qos [ in-policy in_policy_name | out-policy out_policy_name | merge-level merge_level ] Specify the QOS input policy name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Specify the merge level. 0 = merge disabled, 0 = merge enabled + level.
Must be an integer.
Specify the QOS output policy name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Use this command to configure QoS input policy parameters.
Configures service accounting parameters.
Exec > Global Configuration (config) > Feature Template Profile Configuration (config-feature-template-feature_template_name )
service-accounting [ [ enable ] [ aaa-profile aaa_profile_name ] [ periodic-interval interim_interval ] ] Specify the AAA profile to use for service accounting.
Specify to enable service accounting.
Specify the interim interval in seconds.
Must be an integer in the range of 60-4320000.
Use this command to configure service accounting parameters.
Configures session accounting parameters.
Exec > Global Configuration (config) > Feature Template Profile Configuration (config-feature-template-feature_template_name )
session-accounting enable { aaa-profile aaa_profile_name | periodic-interval interim_interval | dual-stack-delay dual_stack_delay_wait } Specify the AAA profile to use for session accounting.
Specify the dual stack set delay wait in seconds.
Must be an integer in the range of 1-30.
Specify to enable session accounting.
Specify the interim interval in seconds.
Must be an integer in the range of 60-4320000.
Use this command to configure session accounting parameters.
Configures PPPOE Subscriber profiles.
Exec > Global Configuration (config)
profile pppoe pppoe_profile_name [ [ ac-cookie ac_cookie ] [ ac-name ac_name ] [ ctrl-pkt-priority priority ] [ service-name pppoe_service_names ] [ service-selection-disable { false | true } ] [ timeout-completion session_completion_timeout ] ] Specify the CoS bits to use in PADx packets.
Must be an integer in the range of 0-7.
Default Value: 0.
Specify the PPPOE MTU for LCP negotiation.
Must be an integer in the range of 500-2000.
Default Value: 1492.
Specify the supported PPPoE service names. You can simultaneously configure multiple service names.
Specify to disable or enable the advertising of extra service names in PADO packets.
Must be one of the following:
false
true
Default Value: false.
Specify the PPPOE profile name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Specify the the AC-Name to use in PADO packets.
Specify the CoS bits to use in PADx packets.
Must be an integer in the range of 0-7.
Default Value: 0.
Specify the PPPOE MTU for LCP negotiation.
Must be an integer in the range of 500-2000.
Default Value: 1492.
Specify the supported PPPoE service names. You can simultaneously configure multiple service names.
Specify to disable or enable the advertising of extra service names in PADO packets.
Must be one of the following:
false
true
Default Value: false.
Specify the PPPOE profile name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Specify the AC-Cookie to use in PADO packets.
Specify the the AC-Name to use in PADO packets.
Specify the CoS bits to use in PADx packets.
Must be an integer in the range of 0-7.
Default Value: 0.
Specify the PPPOE MTU for LCP negotiation.
Must be an integer in the range of 500-2000.
Default Value: 1492.
Specify the supported PPPoE service names. You can simultaneously configure multiple service names.
Specify to disable or enable the advertising of extra service names in PADO packets.
Must be one of the following:
false
true
Default Value: false.
Specify the PPPOE profile name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Specify the AC-Cookie to use in PADO packets.
Specify the the AC-Name to use in PADO packets.
Specify the CoS bits to use in PADx packets.
Must be an integer in the range of 0-7.
Default Value: 0.
Specify the PPPOE MTU for LCP negotiation.
Must be an integer in the range of 500-2000.
Default Value: 1492.
Specify the supported PPPoE service names. You can simultaneously configure multiple service names.
Specify to disable or enable the advertising of extra service names in PADO packets.
Must be one of the following:
false
true
Default Value: false.
Specify the maximum wait time for session to be completed.
Must be an integer in the range of 3-600.
Default Value: 180.
Specify the PPPOE profile name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Use this command to configure PPPOE Subscriber profiles. Enters the PPPOE Profile Configuration mode.
Configures a range for the ppp-max payload tag value.
Exec > Global Configuration (config) > PPPOE Profile Configuration (config-pppoe-pppoe_profile_name )
max-payload { deny | minimum minimum_payload_value | maximum maximum_payload_value } Specify to deny the PPP-max payload value.
Specify the maximum payload value.
Must be an integer in the range of 1-40000.
Default Value: "1500".
Specify the minimum value for the payload.
Must be an integer in the range of 1-40000.
Default Value: "1492".
Use this command to configure a range for the ppp-max payload tag value.
Configures the maximum number of sessions allowed per Circuit-ID.
Exec > Global Configuration (config) > PPPOE Profile Configuration (config-pppoe-pppoe_profile_name )
session-limit circuit-id value [ threshold threshold_count ] Specify the threshold count.
Must be an integer in the range of 1-65535.
Specify the attribute value.
Must be an integer in the range of 1-65535.
Use this command to configure the maximum number of sessions allowed per Circuit-ID.
Configures the maximum number of sessions allowed per peer MAC address.
Exec > Global Configuration (config) > PPPOE Profile Configuration (config-pppoe-pppoe_profile_name )
session-limit mac value [ threshold threshold_count ] Specify the threshold count.
Must be an integer in the range of 1-65535.
Specify the attribute value.
Must be an integer in the range of 1-65535.
Use this command to configure the maximum number of sessions allowed per peer MAC address.
Configures the maximum number of sessions allowed under the PPPoE profile.
Exec > Global Configuration (config) > PPPOE Profile Configuration (config-pppoe-pppoe_profile_name )
session-limit max value [ threshold threshold_count ] Specify the threshold count.
Must be an integer in the range of 1-65535.
Specify the attribute value.
Must be an integer in the range of 1-65535.
Use this command to configure the maximum number of sessions allowed under the PPPoE profile.
Configures the maximum number of sessions allowed per outer-vlan, per access interface.
Exec > Global Configuration (config) > PPPOE Profile Configuration (config-pppoe-pppoe_profile_name )
session-limit outer-vlan value [ threshold threshold_count ] Specify the threshold count.
Must be an integer in the range of 1-65535.
Specify the attribute value.
Must be an integer in the range of 1-65535.
Use this command to configure the maximum number of sessions allowed per outer-vlan, per access interface.
Configures RADIUS client profile parameters.
Exec > Global Configuration (config)
profile radius [ algorithm radius_server_selection_algorithm | deadtime dead_time | max-retry max_retry | timeout retransmit_timeout_duration ] Specify the algorithm for selecting RADIUS server.
Must be one of the following:
first-server : Highest priority first.
round-robin : Round-robin.
least-outstanding: Least number of outstanding transactions.
Specify the time to elapse, in minutes, between RADIUS server marked unreachable and when connection can be re-attempted.
Must be an integer in the range of 0-65535.
Specify the maximum number of times the system must attempt retry with the RADIUS server.
Must be an integer in the range of 0-65535.
Specify the time duration to wait for response from the RADIUS server before retransmitting.
Must be an integer in the range of 1-65535.
Use this command to configure RADIUS client parameters. Enters the RADIUS Client Profile Configuration mode.
Configures RADIUS accounting parameters.
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius)
profile radius accounting
algorithm { first-server | round-robin }
attribute { nas-identifier value | nas-ip { ipv4_address | user-plane-ip } |
nas-port { nas_port } | { format-e format_e
{ nas-port-type nas_port_type } }
deadtime value
detect-dead-server response-timeout value
max-retry value
timeout value
commit
Specify the algorithm for selecting RADIUS server.
Must be one of the following:
first-server : Highest priority first.
round-robin : Round-robin.
Configures the RADIUS identification parameters.
nas-identifier value : Specifies the attribute name by which the system will be identified in Accounting-Request messages. value must be an alphanumeric string.
nas-ip ipv4_address : Specifies the NAS IPv4 address. ipv4_address must be an IPv4 address in dotted decimal notation.
nas-ip user-plane-ip : Enables the user-plane-ip-address AVPair to use the configured User-Plane IP address in Accounting-Request messages.
nas-port { nas_port } | { format-e format_e { nas-port-type nas_port_type } } : Specifies the nas-port attributes.
nas_port configures the NAS port value. The NAS port value ranges from 1 to 4294967295.
 Note |
If none of the NAS port configurations are present, the existing default nas-port logic is applied. That is, setting a fixed-number per radius-pod. |
format-e format_e_value : Specifies the custom attribute formation support for nas-port. The nas-port is a 32 bit integer format. The configuration takes a 32 length of characters, each presenting a particular attribute mapping. The format_e_value pattern is: 01FSAPRiLUVQ]*):
0 – Set bit to 0
1 – Set bit to 1
F - PHY_SHELF
S – PHY_SLOT
A – PHY_ADAPTER
P - PHY_PORT
R - PHY_CHASSIS
i - PHY_SUBSLOT
L - PHY_CHANNEL
V - OUTER_VLAN_ID
Q - INNER_VLAN_ID
U - PPPOE_SESSION_ID
nas-port-type nas_port_type : Specifies the NAS port type. The supported values range from 0 to 44.
Note |
|
Sets the time to elapse, in minutes, between RADIUS server marked unreachable and when connection can be re-attempted.
Must be an integer in the range of 0-65535. Default: 10 minutes.
Sets the timeout value that marks a server as "dead" when a packet is not received for the specified number of seconds.
value must be an integer from 1 through 65535. Default: 10 seconds.
Sets the maximum number of times the system must attempt retry with the RADIUS server.
Must be an integer in the range of 0-65535. Default: 2
Sets the time duration to wait for response from the RADIUS server before retransmitting.
Must be an integer in the range of 1-65535. Default: 2 seconds.
Use this command to configure RADIUS accounting parameters. Enters the RADIUS Accounting Configuration mode.
Configures the AAA called-station-id attribute.
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius)
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius) > RADIUS Accounting Configuration (config-accounting)
attribute called-station-id value Specify the value of the AAA called-station-id attribute.
Must be a string.
Use this command to configure the AAA called-station-id attribute.
Configures the AAA calling-station-id attribute.
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius)
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius) > RADIUS Accounting Configuration (config-accounting)
attribute calling-station-id value Specify the value of the AAA calling-station-id attribute.
Must be a string.
Use this command to configure the AAA calling-station-id attribute.
Configures the AAA nas-identifier-format attribute.
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius)
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius) > RADIUS Accounting Configuration (config-accounting)
attribute nas-identifier-format value Use this command to configure the AAA nas-identifier-format attribute.
Configures the AAA nas-port-id attribute.
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius)
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius) > RADIUS Accounting Configuration (config-accounting)
attribute nas-port-id value Specify value of the AAA nas-port-id attribute.
Must be a string.
Use this command to configure the AAA nas-port-id attribute.
Configures parameters to detect a dead RADIUS server.
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius)
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius) > RADIUS Accounting Configuration (config-accounting)
detect-dead-server response-timeout response_timeout_duration Specify the time duration, in seconds, for a response from the RADIUS server to mark it as unreachable.
Must be an integer in the range of 1-65535.
Use this command to configure parameters to detect a dead RADIUS server.
Configures the AAA called-station-id attribute.
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius)
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius) > RADIUS Accounting Configuration (config-accounting)
attribute called-station-id value Specify the attribute format name.
Must be a string.
Specify the value of the AAA called-station-id attribute.
Must be a string.
Use this command to configure the AAA called-station-id attribute.
Configures node parameters.
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius)
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius) > RADIUS Accounting Configuration (config-accounting)
attribute attribute_name format nas-port-type nas_port_type format-name format_name Specify the Nas-Port-Type value to apply format name on.
Must be an integer.
Specify the attribute format name.
Must be a string.
Specify the Nas-Port-Type value to apply format name on.
Must be an integer.
Use this command to configure node parameters for nas-port-id, calling-station-id, called-station-id, nas-identifier-format.
Configures the AAA calling-station-id attribute.
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius)
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius) > RADIUS Accounting Configuration (config-accounting)
attribute calling-station-id value Specify the attribute format name.
Must be a string.
Specify the value of the AAA calling-station-id attribute.
Must be a string.
Use this command to configure the AAA calling-station-id attribute.
Configures node parameters.
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius)
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius) > RADIUS Accounting Configuration (config-accounting)
attribute attribute_name format nas-port-type nas_port_type format-name format_name Specify the Nas-Port-Type value to apply format name on.
Must be an integer.
Specify the attribute format name.
Must be a string.
Specify the Nas-Port-Type value to apply format name on.
Must be an integer.
Use this command to configure node parameters for nas-port-id, calling-station-id, called-station-id, nas-identifier-format.
Configures the AAA nas-identifier-format attribute.
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius)
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius) > RADIUS Accounting Configuration (config-accounting)
attribute nas-identifier-format value Specify the attribute format name.
Must be a string.
Use this command to configure the AAA nas-identifier-format attribute.
Configures node parameters.
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius)
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius) > RADIUS Accounting Configuration (config-accounting)
attribute attribute_name format nas-port-type nas_port_type format-name format_name Specify the Nas-Port-Type value to apply format name on.
Must be an integer.
Specify the attribute format name.
Must be a string.
Specify the Nas-Port-Type value to apply format name on.
Must be an integer.
Use this command to configure node parameters for nas-port-id, calling-station-id, called-station-id, nas-identifier-format.
Configures the NAS IPv4 or User-Plane IP address.
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius)
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius) > RADIUS Attribute Configuration (config-attribute)
attribute nas-ip { ipv4_address | user-plane-ip } Specifies the AAA NAS IPv4 address.
Enables the user-plane-ip-address AVPair to use the configured User-Plane IP address in Access-Request or Accounting-Request messages.
Use this command to configure the AAA NAS-IP attribute.
Configures the AAA nas-port-id attribute.
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius)
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius) > RADIUS Accounting Configuration (config-accounting)
attribute nas-port-id value Specify the attribute format name.
Must be a string.
Specify value of the AAA nas-port-id attribute.
Must be a string.
Use this command to configure the AAA nas-port-id attribute.
Configures node parameters.
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius)
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius) > RADIUS Accounting Configuration (config-accounting)
attribute attribute_name format nas-port-type nas_port_type format-name format_name Specify the Nas-Port-Type value to apply format name on.
Must be an integer.
Specify the attribute format name.
Must be a string.
Specify the Nas-Port-Type value to apply format name on.
Must be an integer.
Use this command to configure node parameters for nas-port-id, calling-station-id, called-station-id, nas-identifier-format.
Configures parameters to detect a dead RADIUS server.
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius)
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius) > RADIUS Accounting Configuration (config-accounting)
detect-dead-server response-timeout response_timeout_duration Specify the time duration, in seconds, for a response from the RADIUS server to mark it as unreachable.
Must be an integer in the range of 1-65535.
Use this command to configure parameters to detect a dead RADIUS server.
Configures RADIUS external server configuration.
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius)
server radius_server_ip_address radius_server_port_number [ priority radius_server_priority | secret radius_server_secret | type server_type ] Specify the priority of the RADIUS server.
Must be an integer in the range of 1-100.
Specify the secret of the RADIUS server.
Must be an aes-cfb-128-encrypted string.
Specify the server type.
Must be one of the following:
acct
auth
Default Value: auth.
Specify the IP address of the RADIUS server.
Must be an IP address.
Specify the port number of the RADIUS server.
Must be an integer in the range of 1-65535.
Use this command to configure RADIUS external server configuration.
Configures association of RADIUS servers to groups.
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius)
server-group server_group_name Specify the server group name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Use this command to configure association of RADIUS servers to groups. Enters the Server Group Configuration mode.
Configures RADIUS server information.
Exec > Global Configuration (config) > RADIUS Profile Configuration (config-radius) > RADIUS Server Group Configuration (config-server-group-server_group_name )
server radius_server_type ip radius_server_ip_address port radius_port_number Specify IP address of the RADIUS server.
Specify the port number of the RADIUS server.
Specify the server type.
Must be one of the following:
acct : Server used for accounting requests.
auth : Server is used for authentication/authorization requests.
Use this command to configure RADIUS server information.
Configures AAA custom server groups.
Exec > Global Configuration (config)
server-group server_group_name radius-group radius_server_group_name Specify the RADIUS server group name.
Specify the AAA server group name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Use this command to configure AAA custom server groups.
Configures subscriber profiles.
Exec > Global Configuration (config)
profile subscriber subscriber_profile_name [ [ activate-feature-templates template_names ] [ apply-all-class ] [ dhcp-profile dhcp_profile_name ] [ pppoe-profile pppoe_profile_name ] [ session-type session_type ] ] Specify the list of feature templates to activate.
Specify to apply all classes if enabled.
Specify the DHCP-FSOL profile name.
Specify the PPPOE-FSOL profile name.
Specify the allowed session type.
Must be one of the following:
ipv4
ipv4v6
ipv6
Default Value: ipv4v6.
Specify the subscriber profile name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Use this command to configure subscriber profiles. Enters the Subscriber Profile Configuration mode.
You can configure a maximum of "8" elements with this command.
Configures AAA operations.
Exec > Global Configuration (config) > Subscriber Profile Configuration (config-subscriber-subscriber_profile_name )
Exec > Global Configuration (config) > Subscriber Profile Configuration (config-subscriber-subscriber_profile_name ) > Class Configuration (config-class-class_name )
Exec > Global Configuration (config) > Subscriber Profile Configuration (config-subscriber-subscriber_profile_name ) > Event Configuration (config-event-event_name )
Exec > Global Configuration (config) > Subscriber Profile Configuration (config-subscriber-subscriber_profile_name ) > Event Configuration (config-event-event_name ) > Class Configuration (config-class-class_name )
aaa aaa_option aaa_profile_name Specify the AAA option.
Must be one of the following:
authenticate
authorize
Specify the AAA profile name.
Use this command to configure AAA operations.
Configures subscriber classification parameters.
Exec > Global Configuration (config) > Subscriber Profile Configuration (config-subscriber-subscriber_profile_name )
Exec > Global Configuration (config) > Subscriber Profile Configuration (config-subscriber-subscriber_profile_name ) > Event Configuration (config-event-event_name )
class class_name [ activate-feature-templates feature_template_names ] Specify the list of feature template names to activate.
Specify the class name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Use this command to configure subscriber classification parameters. Enters the Subscriber Class Configuration mode.
You can configure a maximum of "8" elements with this command.
Configures AAA operations.
Exec > Global Configuration (config) > Subscriber Profile Configuration (config-subscriber-subscriber_profile_name ) > Subscriber Class Configuration (config-class-class_name )
aaa aaa_option profile_name Specify the AAA option.
Must be one of the following:
authenticate
authorize
Specify the AAA profile name.
Use this command to configure AAA operations.
Configures the list of match values.
Exec > Global Configuration (config) > Subscriber Profile Configuration (config-subscriber-subscriber_profile_name ) > Class Configuration (config-class-class_name )
Exec > Global Configuration (config) > Subscriber Profile Configuration (config-subscriber-subscriber_profile_name ) > Event Configuration (config-event-event_name ) > Class Configuration (config-class-class_name )
matches [ match-type { all | any } ] Specify the match type.
Use this command to configure the list of match values. Enters the Matches Configuration mode.
Configures match key and value.
Exec > Global Configuration (config) > Subscriber Profile Configuration (config-subscriber-subscriber_profile_name ) > Class Configuration (config-class-class_name ) > Matches Configuration (config-matches)
Exec > Global Configuration (config) > Subscriber Profile Configuration (config-subscriber-subscriber_profile_name ) > Event Configuration (config-event-event_name ) > Class Configuration (config-class-class_name ) > Matches Configuration (config-matches)
match match_key { match_protocol | ascii ascii_string | regex regex_string } Specify the match key.
Specify the ASCII string.
Must be a string.
Specify the regular expression string.
Must be a string.
Specify the match key.
Specify the match protocol.
Must be one of the following:
dhcp
ppp
You can configure a maximum of "2" elements with this command.
You can configure a maximum of "8" elements with this command.
Use this command to configure match key and value.
You can configure a maximum of "8" elements with this command.
Configures subscriber events.
Exec > Global Configuration (config) > Subscriber Profile Configuration (config-subscriber-subscriber_profile_name ) > Event Configuration (config-event-event_name )
event event_name [ activate-feature-templates template_names | apply-all-class | deactivate-feature-templates template_names ] Specify the event name.
Specify the list of feature templates to activate.
Specify to apply all classes if enabled.
Specify the list of feature templates to deactivate.
Specify the event name.
You can configure a maximum of "8" elements with this command.
Use this command to configure subscriber events.
You can configure a maximum of "8" elements with this command.
Configures AAA operations.
Exec > Global Configuration (config) > Subscriber Profile Configuration (config-subscriber-subscriber_profile_name )
Exec > Global Configuration (config) > Subscriber Profile Configuration (config-subscriber-subscriber_profile_name ) > Class Configuration (config-class-class_name )
Exec > Global Configuration (config) > Subscriber Profile Configuration (config-subscriber-subscriber_profile_name ) > Event Configuration (config-event-event_name )
Exec > Global Configuration (config) > Subscriber Profile Configuration (config-subscriber-subscriber_profile_name ) > Event Configuration (config-event-event_name ) > Class Configuration (config-class-class_name )
aaa aaa_option aaa_profile_name Specify the AAA option.
Must be one of the following:
authenticate
authorize
Specify the AAA profile name.
Use this command to configure AAA operations.
Configures subscriber classification.
Exec > Global Configuration
class { class-name class_name | deactivate-feature-templates template_names | activate-feature-templates template_names } Specify the list of feature template names to activate.
Specify the class name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Specify the list of feature template names to deactivate.
You can configure a maximum of "8" elements with this command.
Use this command to configure subscriber classification.
You can configure a maximum of "8" elements with this command.
Configures AAA operations.
Exec > Global Configuration (config) > Subscriber Profile Configuration (config-subscriber-subscriber_profile_name ) > Subscriber Class Configuration (config-class-class_name )
aaa aaa_option profile_name Specify the AAA option.
Must be one of the following:
authenticate
authorize
Specify the AAA profile name.
Use this command to configure AAA operations.
Configures the list of match values.
Exec > Global Configuration (config) > Subscriber Profile Configuration (config-subscriber-subscriber_profile_name ) > Class Configuration (config-class-class_name )
Exec > Global Configuration (config) > Subscriber Profile Configuration (config-subscriber-subscriber_profile_name ) > Event Configuration (config-event-event_name ) > Class Configuration (config-class-class_name )
matches [ match-type { all | any } ] Specify the match type.
Use this command to configure the list of match values. Enters the Matches Configuration mode.
Configures match key and value.
Exec > Global Configuration (config) > Subscriber Profile Configuration (config-subscriber-subscriber_profile_name ) > Class Configuration (config-class-class_name ) > Matches Configuration (config-matches)
Exec > Global Configuration (config) > Subscriber Profile Configuration (config-subscriber-subscriber_profile_name ) > Event Configuration (config-event-event_name ) > Class Configuration (config-class-class_name ) > Matches Configuration (config-matches)
match match_key { match_protocol | ascii ascii_string | regex regex_string } Specify the match key.
Specify the ASCII string.
Must be a string.
Specify the regular expression string.
Must be a string.
Specify the match key.
Specify the match protocol.
Must be one of the following:
dhcp
ppp
Use this command to configure match key and value.
You can configure a maximum of "8" elements with this command.
Displays pending session commits in the database.
Exec
show sessions Use this command to view pending session commits in the database.
Displays instance-wise affinity count.
Exec
show sessions affinity Use this command to view the instance-wise affinity count.
Displays all pending session commits.
Exec
show sessions commit-pending Use this command to view all pending session commits.
Displays diagnostics information.
Exec
show diagnostics Use this command to view diagnostics information.
Displays diagnostics information.
Exec
show diagnostics info Use this command to view diagnostics information.
Displays endpoint status.
Exec
show endpoint all Use this command to view endpoint status for all endpoints.
Displays endpoint information.
Exec
show endpoint info Use this command to view endpoint information.
Displays IPAM data-plane allocations.
Exec
show ipam dp Use this command to view IPAM data-plane allocations.
Displays pool allocation information.
Exec
show ipam pool Use this command to view pool allocation information.
Displays peer information.
Exec
show peers Use this command to view peer information.
Displays information for all peers.
Exec
show peers all Use this command to view information for all peers.
Displays resources information.
Exec
show resources Use this command to view resources information.
Displays resources information.
Exec
show resources info Use this command to view resources information.
Displays RPC information.
Exec
show rpc Use this command view RPC information.
Displays information for all RPCs.
Exec
show rpc all Use this command to view information for all RPCs.
Displays system running status information.
Exec
show running-status Use this command to view system running status information.
Displays system running status information.
Exec
show running-status info Use this command to view system running status information.
Displays BNG subscriber data.
Exec
show subscriber type [ count | detail | sublabel subscriber_label ] Specify the accounting session ID.
Must be a string.
Specify to display the number of sessions.
Specify debug information.
Specify to display detailed information.
Specify the subscriber label.
Must be a string.
Specify synchronization information.
Must be one of the following:
synchronize
Specify UPF information.
Must be a string.
Specify SMUP information.
Specify the type.
Must be one of the following:
charging
dhcp
pppoe
session
Use this command to view BNG subscriber data.
Displays subscriber information.
Exec
show subscriber { all | supi supi_id } Specify all SUPI.
Specify the SUPI.
Must be a string.
Use this command to view summary and detailed subscriber information for all subscribers or specific subscribers based on SUPI.
Configures additional filters.
Exec
show subscriber type filter [ afi address_family | iana-state-bound iana_bound_state | iapd-state-bound iapd_bound_state | ipv4-addr ipv4_address | ipv4-pool ipv4_pool_name | ipv4-range ipv4_address_range | ipv4-state-bound ipv4_bound_state | ipv6-addr ipv6_address | ipv6-addr-pool ipv6_address_pool_name | ipv6-addr-range ipv6_address_range | ipv6-pfx ipv6_prefix | ipv6-pfx-pool ipv6_prefix_pool | ipv6-pfx-range ipv6_prefix_range | mac mac_address | port-id upf_port_id | state session_state | up-subs-id up_subscriber_id | upf upf_name | upmgr sm_up_info | username session_user_name | vrf vrf_name ] Specify the address family.
Must be one of the following:
dual
ipv4
ipv6
pending
Specify the IANA bound state.
Must be one of the following:
iana-state-bound
Specify the IAPD bound state.
Must be one of the following:
iapd-state-bound
Specify the IPv4 address in the format "pool-name /ipv4-addr ".
Must be a string.
Specify the IPv4 pool name.
Must be a string.
Specify the IPv4 address range in the format "poolName /start-ip ".
Must be a string.
Specify the IPv4 bound state.
Must be one of the following:
ipv4-state-bound
Specify the IPv6 address pool name.
Must be a string.
Specify the IPv6 address range in the format "poolName /start-ip ".
Must be a string.
Specify the IPv6 address in the format "pool-name /ipv6-addr ".
Must be a string.
Specify the IPv6 prefix pool name.
Must be a string.
Specify the IPv6 prefix range in the format "poolName /start-pfx ".
Must be a string.
Specify the IPv6 prefix in the format "pool-name /ipv6-pfx ".
Must be a string.
Specify the MAC address in the format "aabb.ccdd.eeff".
Must be a string.
Specify the user plane function port ID in the format "upf /portid ".
Must be a string.
Specify the state of the SM session.
Must be one of the following:
created
deleted
established
Specify the state of the SMUP session.
Must be one of the following:
smUpSessionCreated
smUpSessionDeleted
smUpSessionWait4SmCreate
Specify the session state.
Must be one of the following:
complete
incomplete
Specify the UP subscriber ID.
Must be a string.
Specify the user plane function name.
Must be a string.
Specify the UPMgr.
Must be one of the following:
upmgr
Specify the user name of the session.
Must be a string.
Use this command to configure additional filters.
Displays the key values of SRG groups
Exec
show subscriber redundancy [ count | debug | detail | gr-instance gr_instance_id | srg-peer-id srg_peer_id | upf upf_name ] Specify the count of SRG groups
Specify debug information
Specify to display detailed information.
Specify the geo redundancy instance identity.
Specify the identity of peer user plane for the group.
Specify the name of user plane function.
Use this command to view the key values of SRG groups.
Displays the subscriber reconciliation details.
Exec
show subscriber redundancy-sync [ gr-instance gr_instance_id | srg-peer-id srg_peer_id | upf upf_name ] Specify the geo redundancy instance identity.
Specify the identity of peer user plane for the SRG.
Specify the name of user plane function.
Use this command to view the subscriber reconciliation details.
Displays the session manager CDL record keys per session.
Exec
show subscriber session [ detail | filter { smupstate { upf_name/smUpSessionCreated } } ] Display the session details from SM CDL record.
Display whether the session is created in the respective UPF for the SRG sessions.
Use this command to view the session manager CDL record keys per session.
Synchronize information.
Exec
show subscriber synchronize [ srg-peer-id peer_id | upf upf_info ] show subscriber synchronize-cp upf upf_info Specify to synchronise CP information.
Must be one of the following:
synchronize-cp
Specify to synchronise UP information.
Must be one of the following:
synchronize
Specify the identity of peer user plane for the group.
Specify UPF information.
Must be a string of 1-64 characters.
Use this command to synchronise information.
Enables/disables DHCP IP Lease Reservation.
Exec > Global Configuration (config)
[ no ] subscriber featurette dhcp-lease-reservation enable Enables DHCP IP Lease Reservation
Disables DHCP IP Lease Reservation
Use this command to enable or disable DHCP IP Lease Reservation.
Configures subscriber geographical redundancy group.
Exec > Global Configuration > Userplane Configuration (config-user-plane-userplane_name )
subscriber-redundancy group group_name { disable | domain-identifier domain-name | peer-identifier peer-id | port-id-map port-name port-id name port-id| [ preferred-role-active ] [ revertive-timer sec ] } Specifies the name of the subscriber redundancy group that is unique to a user plane.
Disables an SRG group without deleting the entire configuration of the group. The behaviour is same as removing an SRG group.
Specifies the domain name to identify all groups common between two userplanes.
Identifies the peer user-plane for the group. This identifier must be unique across all groups in the control plane. The same peer-identifier must be configured in the peer user-plane.
Specifies the mapping of access interfaces between user planes. At least one port-id-map must be configured.
This is an optional configuration.
Sets the preferred role active for user plane. If preferred-role-active is not configured, none of the UPs under the SRG group will be active. Default value: false.
This is an optional configuration.
Specifies the revertive timer in seconds. revertive_timer_value must be an integer in the range of 60 to 3600. This command is available only when preferred-role-active is configured.
Use this command to configure the subscriber redundancy group (SRG) configuration.
Synchronizes the sessions with the standby UP.
Exec
subscriber-redundancy session-synchronize add { domain [ domain_ID ] | duration timeout_value | peer-id [ peer_id ] | target-upf upf_id | tps value | upf [ upf_id ] } Specifies the list of SRG domains.
Specifies the maximum timeout value in minutes.
Specifies the list of SRG peer identities.
Specifies the identity of target UP.
Specifies the maximum number of allowed transactions per second (TPS).
Specifies the list of UPs.
Deletes SRG sessions.
Exec
subscriber-redundancy session-synchronize delete { domain [ domain_ID ] | duration timeout_value | peer-id [ peer_id ] | target-upf upf_id | tps value | upf [ upf_id ] } Specifies the list of SRG domains.
Specifies the maximum timeout value in minutes.
Specifies the list of SRG peer identities.
Specifies the identity of target UP.
Specifies the maximum number of allowed transactions per second (TPS).
Specifies the list of UPs.
Configure to reset the in-use token for the specified protocol.
Exec
subscriber reset-token { dhcp | pppoe } Reset the in-use token to zero for DHCP or PPPoE.
Use this command to reset the in-use token to zero.
Synchronizes routes to UPF.
Exec
subscriber route-synchronize upf user_plane_name Specify the user plane name.
Must be a string.
Use this command to synchronize routes to UPF.
Synchronizes sessions to UPF.
Exec
subscriber session-synchronize upf user_plane_name [ abort | timeout sla_timeout ] Specify to abort synchronization.
Specify the SLA timeout duration in seconds.
Must be an integer in the range of 10-1800.
Specify the user plane name.
Must be a string.
Use this command to synchronize sessions to UPF.
Synchronizes sessions on CP.
Exec
subscriber session-synchronize-cp upf user_plane_name [ abort | timeout timeout_value | tps tps ] Specify to abort synchronization.
Specify the timeout duration in minutes.
Must be an integer in the range of 2-100.
Specify the TPS.
Must be an integer in the range of 40-4000.
Specify name of the user plane function.
Must be a string of 1-64 characters.
Use this command to synchronize sessions on CP.
Configures FSOL token mechanism.
Exec > Global Configuration (config)
subscriber token { dhcp | pppoe } token_count Set the maximum token available for FSOL pod.
token_count is cumulative across instances. For example, if there are 4 DHCP pods and DHCP token is set as 2000, then 500 tokens will be assigned for each pod
dhcp : Set the DHCP pod token count.
pppoe : Set the PPPoE pod token count.
Use this command to configure FSOL token mechanism.
Configures the userplane configuration.
Exec > Global Configuration (config)
user-plane userplane_name [ offline | subscriber-profile subscriber_profile ] Specify as offline.
Specify the Subscriber Profile to associate at current level.
Specify the userplane name.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Use this command to configure the userplane configuration. Enters the Userplane Configuration mode.
Configures the associated flow control group in user plane.
Exec > Global Configuration > Userplane Configuration (config-user-plane-userplane_name )
flowctrl-group group_name Specify the flow control group to be associated.
Use this command to associate the flow control group in user plane.
Configures the userplane IP address.
Exec > Global Configuration (config) > User Plane Configuration (config-user-plane-userplane_name )
peer-address ipv4 ipv4_address Specify the IPv4 address.
Must be an IPv4 address.
Use this command to configure the userplane IP address.
Configures Port Identifier parameters.
Exec > Global Configuration (config) > User Plane Configuration (config-user-plane-userplane_name )
port-id port_number [ subscriber-profile subscriber_profile_name ] Specify the Subscriber Profile to associate to the Port Identifier level.
Specify the port identifier.
Must be a string in the pattern ([a-zA-Z1-9_][^(\\s,\\t,\",')]*).
Use this command to configure Port Identifier parameters.
Feedback