Virtual Private Network Command Reference for Cisco CRS Series Routers

advertise-mac

To advertise local MAC to the peers, use advertise-mac command in the EVPN configuration mode. The local MAC is advertised to the peer in control plane using BGP.

advertise-mac

Syntax Description

This command has no keywords or arguments.

Command Default

None

Command Modes

EVPN

Command History


Release	Modification
Release 6.2.1	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Examples

The following example shows how to advertise local MAC.

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:router(config)# evpn
RP/0/RSP0/CPU0:router(config-evpn)# evi 1
RP/0/RSP0/CPU0:router(config-evpn-evi)# bgp
RP/0/RSP0/CPU0:router(config-evpn-evi-bgp)# table-policy spp-basic-6 
RP/0/RSP0/CPU0:router(config-evpn-evi-bgp)# route-target import 100:6005
RP/0/RSP0/CPU0:router(config-evpn-evi-bgp)# route-target export 100:6005
RP/0/RSP0/CPU0:router(config-evpn-evi-bgp)# exit
RP/0/RSP0/CPU0:router(config-evpn-evi)# advertise-mac

authentication (L2TP)

To enable L2TP authentication for a specified L2TP class name, use the authentication command in L2TP class configuration mode. To return to the default behavior, use the no form of this command.

authentication

no authentication

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

L2TP class configuration

Command History


Release	Modification
Release 3.9.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Note

You can also enable L2TP authentication for a specified class name from L2TP class configuration submode. To enter this submode, enter the l2tp-class command followed by the class name.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to configure L2TP authentication for the specified L2TP class name “cisco”:

RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2tp-class cisco 
RP/0/RP0/CPU0:router(config-l2tp-class)# authentication

Related Commands

Command	Description
hello-interval (L2TP)	Configures the hello-interval value for L2TP (duration between control channel hello packets).
hidden (L2TP)	Enables hidden attribute-value pairs (AVPs).
hostname (L2TP)	Defines the name used in the L2TP hostname AVP.
l2tp-class	Enters L2TP class configuration mode where you can define an L2TP signaling template.
password (L2TP)	Defines the password and password encryption type for control channel authentication.
receive-window (L2TP)	Configures the receive window size for the L2TP server.
retransmit (L2TP)	Configures retransmit retry and timeout values.

backup disable (L2VPN)

To specify how long a backup pseudowire should wait before resuming primary pseudowire operation after the failure with primary pseudowire has been cleared, use the backup disable command in L2VPN pseudowire class configuration mode. To disable this feature, use the no form of this command.

backup disable {delay value | never}

no backup disable {delay value | never}

Syntax Description


delay `value`	Specifies the number of seconds that elapse after the failure with primary pseudowire has been cleared before the Cisco IOS XR software attempts to activate the primary pseudowire. The range, in seconds, is from 0 to 180. The default is 0.
never	Specifies that the secondary pseudowire does not fall back to the primary pseudowire if the primary pseudowire becomes available again, unless the secondary pseudowire fails.

Command Default

The default disable delay is the value of 0, which means that the primary pseudowire is activated immediately when it comes back up.

Command Modes

L2VPN pseudowire class configuration

Command History


Release	Modification
Release 3.8.0	This command was introduced.
Release 5.2.1	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how a backup delay is configured for point-to-point pseudowire in which the backup disable delay is set to 50 seconds:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# pw-class class1
RP/0/RP0/CPU0:router(config-l2vpn-pwc)# backup disable delay 50
RP/0/RP0/CPU0:router(config-l2vpn-pwc)# exit
RP/0/RP0/CPU0:router(config-l2vpn)# xconnect group A
RP/0/RP0/CPU0:router(config-l2vpn-xc)# p2p rtrx
RP/0/RP0/CPU0:router(config-l2vpn-xc-p2p)# neighbor 10.1.1.1 pw-id 2
RP/0/RP0/CPU0:router(config-l2vpn-xc-p2p-pw)# pw-class class1
RP/0/RP0/CPU0:router(config-l2vpn-xc-p2p-pw)# backup neighbor 10.2.2.2 pw-id 5
RP/0/RP0/CPU0:router(config-l2vpn-xc-p2p-pw-backup)#

Related Commands

Command	Description
l2vpn	Enters L2VPN configuration mode.
neighbor (L2VPN)	Configures a pseudowire for a cross-connect.
p2p	Enters p2p configuration submode to configure point-to-point cross-connects.
pw-class (L2VPN)	Enters pseudowire class submode to define a pseudowire class template.
xconnect group	Configures cross-connect groups.

clear l2route evpn ipv4

To clear either duplicate or frozen flags, or both, from EVPN MAC-IPv4 routes and re-enable local route learning for the corresponding IPv4 addresses, use clear l2route evpn ipv4 command in EXEC mode.

clear l2route evpn ipv4{ ipv4-address} | all[ evi evi ] frozen-flag

Syntax Description


mac `mac-address`	Clears the route for the specified IPv4 address.
all	Clears all EVPN MAC-IPv4 routes that are marked as duplicate or permanently frozen.
evi `evi`	Clears EVPN MAC -IPv4 routes for the specified topology only.
frozen-flag	Clears either duplicate or frozen flag for the MAC-IPv4 routes that are identified by the specified options.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 6.6.1	This command was introduced.

Usage Guidelines

None

Task ID


Task ID	Operation
l2vpn	read, write

Examples

This example shows how to clear duplicate or frozen flags, or both from EVPN MAC-IPv4 routes:


Router# clear l2route evpn ipv4 192.0.2.1 evi 1 frozen-flag

clear l2route evpn ipv6

To clear either duplicate or frozen flags, or both, from EVPN MAC-IPv6 routes and re-enable local route learning for the corresponding IPv6 addresses, use clear l2route evpn ipv6 command in EXEC mode.

clear l2route evpn ipv6 { ipv6-address} | all[ evi evi ] frozen-flag

Syntax Description


mac `mac-address`	Clears the route for the specified IPv6 address.
all	Clears all EVPN MAC-IPv6 routes that are marked as duplicate or permanently frozen.
evi `evi`	Clears EVPN MAC-IPv6 routes for the specified topology only.
frozen-flag	Clear duplicate or frozen flag for the MAC-IPv6 routes that are identified by the specified options.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 6.6.1	This command was introduced.

Usage Guidelines

None

Task ID


Task ID	Operation
l2vpn	read, write

Examples

This example shows how to clear either duplicate or frozen flags, or both, from EVPN MAC-IPv6 routes:


Router# clear l2route evpn IPv6 2001:DB8::1 evi 1 frozen-flag

clear l2route evpn mac

To clear either duplicate or frozen flags, or both, from EVPN MAC routes and re-enable local route learning for the corresponding MAC addresses, use clear l2route evpn mac command in EXEC mode.

clear l2route evpn mac { mac-address} | all[ evi evi ] frozen-flag

Syntax Description


mac `mac-address`	Clears the route for the specified MAC address.
all	Clears all EVPN MAC routes that are marked as duplicate or permanently frozen.
evi `evi`	Clears EVPN MAC routes for the specified topology only.
frozen-flag	Clears duplicate or frozen flag for the MAC routes that are identified by the specified options.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 6.6.1	This command was introduced.

Usage Guidelines

None

Task ID


Task ID	Operation
l2vpn	read, write

Examples

This example shows how to clear duplicate or frozen flags, or both, from EVPN MAC routes:


Router# clear l2route evpn mac 0.12.3456 evi 1 frozen-flag

clear l2tp counters control session

To clear L2TP control counters for a session, use the clear l2tp counters control session command in EXEC mode.

clear l2tp counters control session fsm [event | state transition]

Syntax Description


fsm	(Optional) Clears finite state machine counters.
event	(Optional) Clears state machine event counters.
state	(Optional) Clears state machine state counters.
transition	(Optional) Clears state machine transition counters.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 3.7.0	This command was introduced.
Release 5.2.1	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to clear all L2TP state machine transition counters:


RP/0/RP0/CPU0:router(config-l2vpn-xc-p2p-pw-backup)## clear l2tp counters control session fsm state transition

Related Commands

Command	Description
clear l2tp counters control tunnel	Clears L2TP control counters for a tunnel.
clear l2vpn counters l2tp	Clears L2VPN statistical information, such as, packets dropped.

clear l2tp counters control tunnel

To clear L2TP control counters for a tunnel, use the clear l2tp counters control tunnel command in EXEC mode.

clear l2tp counters control tunnel {all | authentication | id tunnel id}

Syntax Description


all	Clears all L2TP counters, except authentication counters
authentication	Clears tunnel authentication counters.
id `tunnel id`	Clears a specified counter. Range is 1 to 4294967295.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 3.9.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to clear all L2TP control tunnel counters:


RP/0/RP0/CPU0:router# clear l2tp counters control tunnel all

Related Commands

Command	Description
clear l2tp counters control session	Clears L2TP control counters for a session.
clear l2vpn counters l2tp	Clears L2VPN statistical information, such as, packets dropped.

clear l2tp tunnel

To clear L2TP tunnels, use the clear l2tp tunnel command in EXEC mode.

clear l2tp tunnel {all | id tunnel id | l2tp-class class name | local ipv4 ipv4 address | remote ipv4 ipv4 address}

Syntax Description


all	Clears all L2TP tunnels.
id `tunnel id`	Clears a specified tunnel.
l2tp-class `class name`	Clears all L2TP tunnels based on L2TP class name.
local ipv4 `ipv4 address`	Clears all local tunnels based on the specified local IPv4 address.
remote ipv4 `ipv4 address`	Clears all remote tunnels based on the specified local IPv4 address.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 3.9.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to clear all L2TP tunnels:


RP/0/RP0/CPU0:router# clear l2tp tunnel all

Related Commands

Command	Description
clear l2tp counters control session	Clears L2TP control counters for a session.
clear l2tp counters control tunnel	Clears L2TP control counters for a tunnel.

clear l2vpn collaborators

To clear the state change counters for L2VPN collaborators, use the clear l2vpn collaborators command in EXEC mode.

clear l2vpn collaborators

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 3.4.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to clear change counters for L2VPN collaborators:


RP/0/RP0/CPU0:router# clear l2vpn collaborators

Related Commands

Command	Description
show l2vpn collaborators	Displays information about the state of the interprocess communications connections between l2vpn_mgr and other processes.

clear l2vpn counters l2tp

To clear L2VPN statistical information, such as, packets dropped, use the clear l2vpn counters l2tp command in EXEC mode.

clear l2vpn counters l2tp [neighbor ip-address [pw-id value]]

Syntax Description


l2tp	Clears all L2TP counters.
neighbor `ip-address`	(Optional) Clears all L2TP counters for the specified neighbor.
pw-id `value`	(Optional) Configures the pseudowire ID. The range is from 1 to 4294967295.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 3.9.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to clear all L2TP counters:


RP/0/RP0/CPU0:router# clear l2vpn counters l2tp

Related Commands

Command	Description
show l2vpn collaborators	Displays information about the state of the interprocess communications connections between l2vpn_mgr and other processes.

clear l2vpn counters bridge mac-withdrawal

To clear the MAC withdrawal statistics for the counters of the bridge domain, use the clear l2vpn counters bridge mac-withdrawal command in EXEC mode.

clear l2vpn counters bridge mac-withdrawal {all | group group-name bd-name bd-name | neighbor ip-address pw-id value}

Syntax Description


all	Clears the MAC withdrawal statistics over all the bridges.
group `group-name`	Clears the MAC withdrawal statistics over the specified group.
bd-name `bd-name`	Clears the MAC withdrawal statistics over the specified bridge.
neighbor `ip-address`	Clears the MAC withdrawal statistics over the specified neighbor.
pw-id `value`	Clears the MAC withdrawal statistics over the specified pseudowire. The range is from 1 to 4294967295.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 3.9.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to clear the MAC withdrawal statistics over all the bridges:


RP/0/RP0/CPU0:router# clear l2vpn counters bridge mac-withdrawal all

clear l2vpn forwarding counters

To clear L2VPN forwarding counters, use the clear l2vpn forwarding counters command in EXEC mode.

clear l2vpn forwarding counters

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 3.4.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to clear L2VPN forwarding counters:


RP/0/RP0/CPU0:router# clear l2vpn forwarding counters

Related Commands

Command	Description
show l2vpn forwarding	Displays forwarding information from the layer2_fib manager on the line card.

clear l2vpn forwarding counters bridge-domain mirp-lite

To clear L2VPN forwarding MIRP counters, use the clear l2vpn forwarding counters bridge-domain mirp-lite command in EXEC mode.

clear l2vpn forwarding counters bridge-domain mirp-lite {location node-id}

Syntax Description


location `node-id`	Clears the L2VPN forwarding MIRP counters for the specified location.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 4.3.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operation
l2vpn	read, write, execute

Examples

This example shows how to clear all the MIRP counters:

RP/0/RP0/CPU0:router# clear l2vpn forwarding counters bridge-domain mirp-lite location 0/1/CPU0

This example shows how to clear bridge-domain specific MIRP counters:

RP/0/RP0/CPU0:router# clear l2vpn forwarding counters bridge-domain bg1:bd1 mirp-lite location 0/1/CPU0

Related Commands

Command	Description
clear l2vpn forwarding counters	Clears L2VPN forwarding counters.

clear l2vpn forwarding mac-address-table

To clear L2VPN forwarding MAC address tables, use the clear l2vpn forwarding mac-address-table command in EXEC mode.

clear l2vpn forwarding mac-address-table {address address | bridge-domain name | interface type interface-path-id | location node-id}

Syntax Description

address

Clears a specified MAC address.

bridge-domain name

Clears bridge domains learned from a MAC address table.

type

(Optional) Interface type. For more information, use the question mark (?) online help function.

interface-path-id

Physical interface or a virtual interface.

Note

Use the show interfaces command to see a list of all interfaces currently configured on the router.

For more information about the syntax for the router, use the question mark (?) online help function.

location node-id

Clears L2VPN forwarding message counters for the specified location. The node-id argument is entered in the rack/slot/module notation.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 3.5.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read, write, execute

Examples

The following example shows how to clear L2VPN forwarding MAC address tables on a specified node:


RP/0/RP0/CPU0:router# clear l2vpn forwarding mac-address location 1/1/1

Related Commands

Command	Description
show l2vpn forwarding	Displays forwarding information from the layer2_fib manager on the line card.

clear l2vpn forwarding message counters

To clear L2VPN forwarding message counters, use the clear l2vpn forwarding message counters command in EXEC mode.

clear l2vpn forwarding message counters location node-id

Syntax Description


location `node-id`	Clears L2VPN forwarding message counters for the specified location.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 3.5.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to clear L2VPN forwarding message counters on a specified node:


RP/0/RP0/CPU0:router# clear l2vpn forwarding message counters location 0/6/CPU0

Related Commands

Command	Description
show l2vpn forwarding	Displays forwarding information from the layer2_fib manager on the line card.

clear l2vpn forwarding table

To clear an L2VPN forwarding table at a specified location, use the clear l2vpn forwarding table command in EXEC mode.

clear l2vpn forwarding table location node-id

Syntax Description


location `node-id`	Clears L2VPN forwarding tables for the specified location.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 3.4.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to clear an L2VPN forwarding table from a specified location:


RP/0/RP0/CPU0:router# clear l2vpn forwarding table location 1/2/3/5

Related Commands

Command	Description
show l2vpn forwarding	Displays forwarding information from the layer2_fib manager on the line card.

control-word

To enable control word for MPLS encapsulation, use the control-word command in L2VPN pseudowire class encapsulation submode. To disable the control word, use the no form of this command.

control-word

no control-word

Syntax Description

This command has no keywords or arguments.

Command Default

None

Command Modes

L2VPN pseudowire class encapsulation configuration

Command History


Release	Modification
Release 4.2.1	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

This example shows how to enable control word for MPLS encapsulation:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# pw-class pwc1 
RP/0/RP0/CPU0:router(config-l2vpn-pwc)# encapsulation mpls
RP/0/RP0/CPU0:router(config-l2vpn-pwc-mpls)# control-word

digest (L2TP)

To configure digest options, use the digest command in L2TP class configuration mode. To return to the default behavior, use the no form of this command.

digest {check disable | hash {MD5 | SHA1} | secret {0 | 7 | word}}

no digest {check disable | hash {MD5 | SHA1} | secret {0 | 7 | word}}

Syntax Description


check disable	Disables digest checking.
hash {MD5 \| SHA1}	Configures the digest hash method (MD5 or SHA1). Default is MD5.
secret {0 \| 7 \| `word`}	Configures a shared secret for message digest.

Command Default

check disable : Digest checking is enabled by default.

hash : Default is MD5 if the digest command is issued without the secret keyword option and L2TPv3 integrity checking is enabled.

Command Modes

L2TP class configuration

Command History


Release	Modification
Release 3.9.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

The digest secret and hash algorithm can be configured in the l2tp-class configuration for authentication of the control channel. For control channel authentication to work correctly, however, both sides of the L2TP control channel connection must share a common secret and hash algorithm.

To update of digest secret without network disruption, Cisco supports a maximum to two digest secrets. You can configure a new secret while keeping the old secret valid. You can safely remove the old secret after you update all affected peer nodes with a new secret,

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to configure digest options for L2TP:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2tp-class cisco
RP/0/RP0/CPU0:router(config-l2tp-class)# digest check disable
RP/0/RP0/CPU0:router(config-l2tp-class)# digest secret cisco hash md5

Related Commands

Command	Description
authentication (L2TP)	Enables L2TP authentication for a specified L2TP class name.
hello-interval (L2TP)	Configures the hello-interval value for L2TP (duration between control channel hello packets).
hidden (L2TP)	Enables hidden attribute-value pairs (AVPs).
hostname (L2TP)	Defines the name used in the L2TP hostname AVP.
l2tp-class	Enters L2TP class configuration mode where you can define an L2TP signaling template.
password (L2TP)	Defines the password and password encryption type for control channel authentication.
receive-window (L2TP)	Configures the receive window size for the L2TP server.
retransmit (L2TP)	Configures retransmit retry and timeout values.

hello-interval (L2TP)

To configure the hello-interval value for L2TP (duration between control channel hello packets), use the hello interval (L2TP) command in L2TP class configuration mode. To return to the default behavior, use the no form of this command.

hello-interval interval

no hello-interval interval

Syntax Description


`interval`	Interval (in seconds) between control channel hello packets. The range is from 0 to 1000. Default is 60 seconds.

Command Default

interval : 60 seconds

Command Modes

L2TP class configuration

Command History


Release	Modification
Release 3.9.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to configure the hello-interval value for L2TP to 22 seconds:

RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2tp-class cisco
RP/0/RP0/CPU0:router(config-l2tp-class)# hello-interval 22

Related Commands

Command	Description
authentication (L2TP)	Enables L2TP authentication for a specified L2TP class name.
hidden (L2TP)	Enables hidden attribute-value pairs (AVPs).
hostname (L2TP)	Defines the name used in the L2TP hostname AVP.
l2tp-class	Enters L2TP class configuration mode where you can define an L2TP signaling template.
password (L2TP)	Defines the password and password encryption type for control channel authentication.
receive-window (L2TP)	Configures the receive window size for the L2TP server.
retransmit (L2TP)	Configures retransmit retry and timeout values.

hidden (L2TP)

To enable hidden attribute-value pairs (AVPs), use the hidden command in L2TP class configuration mode. To return to the default behavior, use the no form of this command.

hidden

no hidden

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

L2TP class configuration

Command History


Release	Modification
Release 3.9.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to enable hidden AVPs:

RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2tp-class cisco 
RP/0/RP0/CPU0:router(config-l2tp-class)# hidden

Related Commands

Command	Description
authentication (L2TP)	Enables L2TP authentication for a specified L2TP class name.
hello-interval (L2TP)	Configures the hello-interval value for L2TP (duration between control channel hello packets).
hostname (L2TP)	Defines the name used in the L2TP hostname AVP.
l2tp-class	Enters L2TP class configuration mode where you can define an L2TP signaling template.
password (L2TP)	Defines the password and password encryption type for control channel authentication.
receive-window (L2TP)	Configures the receive window size for the L2TP server.
retransmit (L2TP)	Configures retransmit retry and timeout values.

hostname (L2TP)

To define the name used in the L2TP hostname AVP, use the hostname command in L2TP class configuration mode. To return to the default behavior, use the no form of this command.

hostname name

no hostname name

Syntax Description


`name`	Hostname used to identify the router during L2TP control channel authentication.

Command Default

None

Command Modes

L2TP class configuration

Command History


Release	Modification
Release 3.9.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to configure a hostname using the word “cisco”:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2tp-class cisco
RP/0/RP0/CPU0:router(config-l2tp-class)# hostname cisco

Related Commands

Command	Description
authentication (L2TP)	Enables L2TP authentication for a specified L2TP class name.
hello-interval (L2TP)	Configures the hello-interval value for L2TP (duration between control channel hello packets).
hidden (L2TP)	Enables hidden attribute-value pairs (AVPs).
l2tp-class	Enters L2TP class configuration mode where you can define an L2TP signaling template.
password (L2TP)	Defines the password and password encryption type for control channel authentication.
receive-window (L2TP)	Configures the receive window size for the L2TP server.
retransmit (L2TP)	Configures retransmit retry and timeout values.

interface (p2p)

To configure an attachment circuit, use the interface command in p2p configuration submode. To return to the default behavior, use the no form of this command.

interface type interface-path-id [PW-Ether | PW-IW]

no interface type interface-path-id [PW-Ether | PW-IW]

Syntax Description

type

Interface type. For more information, use the question mark (?) online help function.

interface-path-id

Physical interface or a virtual interface.

Note

Use the show interfaces command to see a list of all possible interfaces currently configured on the router.

For more information about the syntax for the router, use the question mark (?) online help function.

PW-Ether

(Optional) Configures an Ethernet Interface.

PW-IW

(Optional) Configures an IP Interworking Interface.

Command Default

None

Command Modes

p2p configuration submode

Command History


Release	Modification
Release 3.4.0	This command was introduced.
Release 4.2.1	The following keywords were added: PW-Ether PW-IW

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to configure an attachment circuit on a TenGigE interface:

RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# xconnect group gr1
RP/0/RP0/CPU0:router(config-l2vpn-xc)# p2p p001
RP/0/RP0/CPU0:router(config-l2vpn-xc-p2p)# interface TenGigE 1/1/1/1

Related Commands

Command	Description
p2p	Enters p2p configuration submode to configure point-to-point cross-connects.

interworking ipv4

To configure IPv4 interworking, use the interworking ipv4 command in the p2p configuration submode. To return to the default behavior, use the no form of this command.

interworking ipv4

no interworking ipv4

Syntax Description


ipv4	Sets IPv4 interworking.

Command Default

None

Command Modes

p2p configuration submode

Command History


Release	Modification

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to configure an attachment circuit on a TenGigE interface:

RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# xconnect group gr1
RP/0/RP0/CPU0:router(config-l2vpn-xc)# p2p gr1
RP/0/RP0/CPU0:router(config-l2vpn-xc-p2p)# interworking ipv4
RP/0/RP0/CPU0:router(config-l2vpn-xc-p2p)#

Related Commands

Command	Description
p2p	Enters p2p configuration submode to configure point-to-point cross-connects.

l2tp-class

To enter L2TP class configuration mode where you can define an L2TP signaling template, use the l2tp-class command in global configuration mode. To delete the L2TP class, use the no form of this command.

l2tp-class l2tp-class-name

no l2tp-class l2tp-class-name

Syntax Description


l2tp-class-name	L2TP class name.

Command Default

No L2TP classes are defined.

Command Modes

Global configuration

Command History


Release	Modification
Release 3.9.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Note

An L2TP class name must be defined before configuring L2TP control plane configuration settings.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to enter L2TP configuration mode to create a template of L2TP control plane configuration settings that can be inherited by different pseudowire classes (in this case, the word “cisco” is used):

RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2tp-class cisco
RP/0/RP0/CPU0:router(config-l2tp-class)#

l2tp static

To enable the Layer 2 Tunneling Protocol (L2TP) static submode, and perform L2TP pseudowire configurations, use the l2tp static command in p2p pseudowire configuration submode. To disable the L2TP static submode, use the no form of this command.

l2tp static [local {cookie {secondary size | size} {0 | 4 | 8} value value | session session id} | remote {cookie size {0 | 4 | 8} value value | session session id}]

no l2tp static [local {cookie {secondary size | size} {0 | 4 | 8} value cookie value | session session id} | remote {cookie size {0 | 4 | 8} value cookie value | session session id}]

Syntax Description


local	(Optional) Configures local cookies and sessions.
cookie	Sets L2TP pseudowire static local or remote cookie.
secondary size	Sets L2TP pseudowire static local cookie secondary size.
size	Sets L2TP pseudowire static local cookie size.
value	Sets the value of the cookie.
`cookie value`	Value of the cookie. The cookie values are specified based on the configured cookie size: Cookie size 0—No cookie value is set. Cookie size 4—Lower 4 bytes value (<0x0-0xffffffff>) is set. Cookie size 8—Lower 4 bytes value and higher 4 bytes values (<0x0-0xffffffff> <0x0-0xffffffff> ) are set.
session	Sets L2TP pseudowire static local or remote session.
`session id`	Session ID. Range is from 1 to 65535.
remote	(Optional) Configures remote cookies and sessions.

Command Default

None

Command Modes

p2p pseudowire configuration

Command History


Release	Modification
Release 4.3.1	This command was introduced

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operation
l2vpn	read, write

Examples

This example shows how to enter the l2tp static configuration sub mode:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn xconnect group l2vpn
RP/0/RP0/CPU0:router(config-l2vpn-xc)# p2p rtrA_to_rtrB
RP/0/RP0/CPU0:router(config-xc-p2p)# neighbor ipv6 1111:2222::cdef pw-id 1
RP/0/RP0/CPU0:router(config-xc-p2p-pw)# l2tp static

This example shows how to configure local and remote session-id:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn xconnect group l2vpn
RP/0/RP0/CPU0:router(config-l2vpn-xc)# p2p rtrA_to_rtrB
RP/0/RP0/CPU0:router(config-xc-p2p)# neighbor ipv6 1111:2222::cdef pw-id 1
RP/0/RP0/CPU0:router(config-xc-p2p-pw)# l2tp static local session 1
RP/0/RP0/CPU0:router(config-xc-p2p-pw)# l2tp static remote session 1

This example shows how to configure cookie size and values:

This example is with cookie size 0:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn xconnect group l2vpn
RP/0/RP0/CPU0:router(config-l2vpn-xc)# p2p rtrA_to_rtrB
RP/0/RP0/CPU0:router(config-xc-p2p)# neighbor ipv6 1111:2222::cdef pw-id 1
RP/0/RP0/CPU0:router(config-xc-p2p-pw)# l2tp static local cookie size 0
RP/0/RP0/CPU0:router(config-xc-p2p-pw)# l2tp static remote cookie size 0

This example is with cookie size 4:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn xconnect group l2vpn
RP/0/RP0/CPU0:router(config-l2vpn-xc)# p2p rtrA_to_rtrB
RP/0/RP0/CPU0:router(config-xc-p2p)# neighbor ipv6 1111:2222::cdef pw-id 1
RP/0/RP0/CPU0:router(config-xc-p2p-pw)# l2tp static local cookie size 4 value <0x0-0xffffffff>
RP/0/RP0/CPU0:router(config-xc-p2p-pw)# l2tp static remote cookie size 4 value <0x0-0xffffffff>

This example is with cookie size 8 (lower 4 bytes entered first and then higher 4 bytes):


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn xconnect group l2vpn
RP/0/RP0/CPU0:router(config-l2vpn-xc)# p2p rtrA_to_rtrB
RP/0/RP0/CPU0:router(config-xc-p2p)# neighbor ipv6 1111:2222::cdef pw-id 1
RP/0/RP0/CPU0:router(config-xc-p2p-pw)# l2tp static local cookie size 8 value <0x0-0xffffffff> <0x0-0xffffffff>
RP/0/RP0/CPU0:router(config-xc-p2p-pw)# l2tp static remote cookie size 8 value <0x0-0xffffffff> <0x0-0xffffffff>

This example show how to configure a secondary local cookie:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn xconnect group l2vpn
RP/0/RP0/CPU0:router(config-l2vpn-xc)# p2p rtrA_to_rtrB
RP/0/RP0/CPU0:router(config-xc-p2p)# neighbor ipv6 1111:2222::cdef pw-id 1
RP/0/RP0/CPU0:router(config-xc-p2p-pw)# l2tp static local cookie secondary size 8 value <0x0-0xffffffff> <0x0-0xffffffff>

Related Commands

Command	Description
l2vpn	Enters L2VPN configuration mode.
p2p	Enters p2p configuration submode to configure point-to-point cross-connects.
xconnect group	Configures cross-connect groups.
neighbor (L2VPN)	Configures a pseudowire for a cross-connect.

l2transport

To configure a physical interface to operate in Layer 2 transport mode, use the l2transport command in interface configuration mode. To return to the default behavior, use the no form of this command.

l2transport

no l2transport

This command has no arguments or keywords.

Command Default

None

Command Modes

Interface configuration

Command History


Release	Modification
Release 3.4.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

The l2transport command and these configuration items are mutually exclusive:

IPv4 address and feature (for example, ACL) configuration
IPv4 enable, address and feature (for example, ACL) configuration
Bundle-enabling configuration
L3 subinterfaces
Layer 3 QoS Policy

Note

After an interface or connection is set to Layer 2 switched, commands such as ipv4 address are not usable. If you configure routing commands on the interface, l2transport is rejected.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to configure an interface or connection as Layer 2 switched under several different modes:

Ethernet Port Mode:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# interface GigabitEthernet 0/0/0/0 
RP/0/RP0/CPU0:router(config-if)# l2transport

Ethernet VLAN Mode:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# interface GigabitEthernet 0/0/0/0.900 l2transport
RP/0/RP0/CPU0:router(config-if)# encapsulation dot1q 100do1q vlan 999

Ethernet VLAN Mode (QinQ):


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# interface GigabitEthernet 0/0/0/0.900 l2transport
RP/0/RP0/CPU0:router(config-if)# encapsulation dot1q 20 second-dot1q 10vlan 999 888

Ethernet VLAN Mode (QinAny) :


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# interface GigabitEthernet 0/0/0/0.900 l2transport
RP/0/RP0/CPU0:router(config-if)# encapsulation dot1q 30 second-dot1q do1q vlan 999 any

Related Commands

Command	Description
show l2vpn forwarding	Displays forwarding information from the layer2_fib manager on the line card.

l2transport l2protocol

To configure Layer 2 protocol handling, use the l2transport l2protocol command in interface configuration mode. To return to the default behavior, use the no form of this command.

l2transport l2protocol {cdp | pvst | stp | vtp} {drop | experimental bits | tunnel experimental bits}

no l2transport l2protocol {cdp | pvst | stp | vtp} {drop | experimental bits | tunnel experimental bits}

Syntax Description


cdp	Configures Cisco Discovery Protocol (CDP).
pvst	Configures Per VLAN Spanning Tree protocol (PVST).
stp	Configures Spanning Tree Protocol (STP).
vtp	Configures VLAN Trunk Protocol (VTP).
drop	Drops the selected protocol packets.
experimental `bits`	Modifies the MPLS experimental bits.
tunnel experimental `bits`	Configures tunnel protocol packets.

Command Default

None

Command Modes

Interface configuration

Command History


Release	Modification
Release 3.9.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

These L2 protocols are available:

Cisco Discovery Protocol (CDP)—CDP is protocol-independent and is used to obtain protocol addresses, platform information, and other data about neighboring devices.
PVST maintains a spanning tree instance for each VLAN configured in the network and permits a VLAN trunk to be forwarding for some VLANs and not for others. It can also load balance Layer 2 traffic by forwarding some VLANs on one trunk and other VLANs n others.
Spanning-Tree Protocol (STP)—STP is a link management protocol that provides path redundancy in the network. For Ethernet networks to function properly, only one active path can exist between two stations.
VLAN Trunk Protocol (VTP)—VTP is a Cisco-proprietary protocol that reduces administration in a switched network. When you configure a new VLAN on one VTP server, the VLAN is distributed through all switches in the domain.

Task ID


Task ID	Operations
l2vpn	read, write
atm	read, write

Examples

The following example shows how to configure Layer 2 protocol handling:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# interface GigabitEthernet 0/0/0/0 
RP/0/RP0/CPU0:router(config-if)# l2transport l2protocol cpsv reverse-tunnelstp drop

Related Commands

Command	Description
show l2vpn forwarding	Displays forwarding information from the layer2_fib manager on the line card.

l2transport propagate

To propagate Layer 2 transport events, use the l2transport propagate command in interface configuration mode. To return to the default behavior, use the no form of this command.

l2transport propagate remote-status

no l2transport propagate remote-status

Syntax Description


remote-status	Propagates remote link status changes.

Command Default

None

Command Modes

Interface configuration

Command History


Release	Modification
Release 3.6.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

The l2transport propagate command provides a mechanism for the detection and propagation of remote link failure for port mode EoMPLS.

Note

If you configure the propagate Layer 2 transport using this command on both ends of the PW (head and tail end), the PW might flap continuously. Use the carrier-delay command on the attachment circuit to stabilize the PW.

To display the state of l2transport events, use the show controller internal command in Interface and Hardware Component Configuration Guide for Cisco CRS Routers

Note

This command is supported on the following Cisco CRS Router SPA cards:

Cisco 1-Port 10 Gigabit Ethernet Shared Port Adapter, Version 2
Cisco 2-port, 5-port, 8-port, and 10-port Gigabit Ethernet Shared Port Adapters
Cisco 2-, 5-, 8-, and 10-Port Gigabit Ethernet Shared Port Adapters, Version 2
Cisco 1-Port 10 Gigabit Ethernet LAN/WAN-PHY Shared Port Adapter

Any port on 6-10GE-WLO-FLEX (irrespective of SPA or fixed) does not support the l2transport propagate command.

For more information about the Ethernet remote port shutdown feature, see MPLS Configuration Guide for the Cisco CRS Routers.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to propagate remote link status changes:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# interface GigabitEthernet 0/0/0/0 
RP/0/RP0/CPU0:router(config-if)# l2transport propagate remote remote-status

Related Commands

Command	Description
show l2vpn forwarding	Displays forwarding information from the layer2_fib manager on the line card.

l2transport service-policy

To configure a Layer 2 transport quality of service (QoS) policy, use the l2transport service-policy command in interface configuration mode. To return to the default behavior, use the no form of this command.

l2transport service-policy {input policy-name | output policy-name}

no l2transport service-policy {input policy-name | output policy-name}

Syntax Description


input `policy-name`	Configures the direction of service policy application: input.
output `policy-name`	Configures the direction of service policy application: output.

Command Default

None

Command Modes

Interface configuration

Command History


Release	Modification
Release 3.9.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read, write
atm	read, write

Examples

The following example shows how configure an L2 transport quality of service (QoS) policy:


RP/0/RSP0RP00/CPU0:router# configure
RP/0/RSP0RP00/CPU0:router(config)# interface GigabitEthernet 0/0/0/0 
RP/0/RSP0RP00/CPU0:router(config-if)# l2transport service-policy input sp_0001

Related Commands

Command	Description
show l2vpn forwarding	Displays forwarding information from the layer2_fib manager on the line card.

l2vpn

To enter L2VPN configuration mode, use the l2vpn command in global configuration mode. To return to the default behavior, use the no form of this command.

l2vpn

no l2vpn

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Release 3.4.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Note

All L2VPN configuration can be deleted using the no l2vpn command.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to enter L2VPN configuration mode:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)#

Related Commands

Command	Description
show l2vpn forwarding	Displays forwarding information from the layer2_fib manager on the line card.

load-balancing flow-label

To balance the load based on flow-labels, use the load-balancing flow label command in the l2vpn pseudowire class mpls configuration submode or l2vpn bridge group bridge-domain vfi autodiscovery bgp or ldp signaling submodes. To undo flow-label based load-balancing, use the no form of this command.

load-balancing flow-label {both | code | receive | transmit} [static]

no load-balancing flow-label {both | code | receive | transmit} [static]

Syntax Description


both	Inserts or discards flow labels on transmit or receive.
code	Specifies the flow label TLV (type-length-value) code. The code value is 17.
receive	Discards flow label on receive.
transmit	Inserts flow label on transmit.
static	Sets flow label parameters statically.

Command Default

None

Command Modes

L2vpn pseudowire class mpls configuration submode

L2vpn bridge group bridge-domain vfi autodiscovery bgp signaling submode

L2vpn bridge group bridge-domain vfi autodiscovery ldp signaling submode

Command History


Release	Modification
Release 4.2.0	This command was introduced.
Release 4.3.2	The code keyword was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

In the draft-ietf-pwe3-fat-pw document, the flow label sub-TLV identifier for the Flow Aware Transport Pseudowire (FAT PW) was 0x11. This value has been changed to 0x17, which is also the sub-TLV identifier assigned by the Internet Assigned Numbers Authority (IANA).

Use the load-balancing flow label code command to toggle between the sub-TLV identifiers—0x11 and 0x17. If there is a mismatch between two endpoints in the load-balancing flow label code, then the PWs will have a mismatched TLV value resulting in a load balancing failure.

The no form of the load-balancing flow label code command uses the flow label sub-TLV identifier 0x11.

Task ID


Task ID	Operation
l2vpn	read, write

Examples

This example shows the output of the load-balancing flow-label command of the both keyword.


RP/0/RP0/CPU0:router#config
RP/0/RP0/CPU0:router(config)#l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)#pw-class p1
RP/0/RP0/CPU0:router(config-l2vpn-pwc)#encapsulation
RP/0/RP0/CPU0:router(config-l2vpn-pwc)#encapsulation mpls
RP/0/RP0/CPU0:router(config-l2vpn-pwc-mpls)#load-balancing
RP/0/RP0/CPU0:router(config-l2vpn-pwc-mpls)#load-balancing flow-label
RP/0/RP0/CPU0:router(config-l2vpn-pwc-mpls)#load-balancing flow-label both
RP/0/RP0/CPU0:router(config-l2vpn-pwc-mpls)#load-balancing flow-label both static

Related Commands

Command	Description
pw-class encapsulation mpls	Configures MPLS pseudowire encapsulation.

logging (l2vpn)

To enable cross-connect logging, use the logging command in L2VPN configuration submode. To return to the default behavior, use the no form of this command.

logging pseudowire status

no logging pseudowire status

Syntax Description


pseudowire status	Enables pseudowire state change logging.

Command Default

None

Command Modes

L2VPN configuration submode

Command History


Release	Modification
Release 3.5.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Note

All L2VPN configuration can be deleted using the no l2vpn command.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to enable cross-connect logging:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# logging pseudowire status

Related Commands

Command	Description
l2vpn	Enters L2VPN configuration mode.

logging nsr

To enable non-stop routing logging, use the logging nsr command in L2VPN configuration submode. To return to the default behavior, use the no form of this command.

logging nsr

no logging nsr

Syntax Description

This command has no keywords or arguments.

Command Default

None

Command Modes

L2VPN configuration submode

Command History


Release	Modification
Release 4.3.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Note

All L2VPN configuration can be deleted using the no l2vpn command.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to enable non-stop routing logging:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# logging nsr

Related Commands

Command	Description
l2vpn	Enters L2VPN configuration mode.

monitor-session (l2vpn)

To attach a traffic monitoring session as one of the segments for a cross connect, use the monitor-session command in point-to-point cross connect configuration mode. To remove the association between a traffic mirroring session and a cross connect, use the no form of this command.

monitor-session session-name

no monitor-session session-name

Syntax Description


`session-name`	Name of the monitor session to configure.

Command Default

No default behavior or values

Command Modes

Point-to-point cross connect configuration

Command History


Release	Modification
Release 4.0.0	This command was introduced.

Usage Guidelines

Before you can attach a traffic mirroring session to a cross connect, you must define it using the monitor-session global configuration command. Once the traffic mirroring session is defined, use the monitor-session point-to-point cross connect configuration command to attach this session as one of the segments for the cross connect. Once attached, all traffic replicated from the monitored interfaces (in other words, interfaces that are associated with the monitor-session) is replicated to the pseudowire that is attached to the other segment of the cross-connect.

The session-name argument should be different than any interface names currently used in the system.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

This example shows how to attach a traffic mirroring session as segment for the xconnect:


RP/0/RSP0/CPU0:router(config)# l2vpn 
RP/0/RSP0/CPU0:router(config-l2vpn)# xconnect group g1 
RP/0/RSP0/CPU0:router(config-l2vpn-xc)# p2p xcon1 
RP/0/RSP0/CPU0:router(config-l2vpn-xc-p2p)# monitor-session mon1

Related Commands

Command	Description
See the monitor session command in the Interface and Hardware Component Command Reference for Cisco CRS Routers.

mpls static label (L2VPN)

To configure static labels for MPLS L2VPN, use the mpls static label command in L2VPN cross-connect P2P pseudowire configuration mode. To have MPLS assign a label dynamically, use the no form of this command.

mpls static label local label remote value

no mpls static label local label remote value

Syntax Description


local `label`	Configures a local pseudowire label. Range is 16 to 15999.
remote `value`	Configures a remote pseudowire label. Range is 16 to 15999.

Command Default

The default behavior is a dynamic label assignment.

Command Modes

L2VPN cross-connect P2P pseudowire configuration

Command History


Release	Modification
Release 3.7.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to configure static labels for MPLS L2VPN:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn xconnect group l2vpn
RP/0/RP0/CPU0:router(config-l2vpn-xc)# p2p rtrA_to_rtrB
RP/0/RP0/CPU0:router(config-xc-p2p)# neighbor 10.1.1.2 pw-id 1000
RP/0/RP0/CPU0:router(config-l2vpn-xc-p2p-pw)# mpls static label local 800 remote 500

Related Commands

Command	Description
l2vpn	Enters L2VPN configuration mode.
neighbor (L2VPN)	Configures a pseudowire for a cross-connect.
p2p	Enters p2p configuration submode to configure point-to-point cross-connects.
xconnect group	Configures cross-connect groups.

neighbor (L2VPN)

To configure a pseudowire for a cross-connect, use the neighbor command in p2p configuration submode. To return to the default behavior, use the no form of this command.

neighbor A.B.C.D pw-id value [backup | mpls | | pw-class | tag-impose]

no neighbor A.B.C.D pw-id value [backup | mpls | | pw-class | tag-impose]

Syntax Description


`A.B.C.D`	IP address of the cross-connect peer.
pw-id `value`	Configures the pseudowire ID and ID value. Range is 1 to 4294967295.
tag-impose	Optional Specifies a tag during a VLAN ID configuration.

Command Default

None

Command Modes

p2p configuration submode

Command History


Release	Modification
Release 3.4.0	This command was introduced.
Release 3.4.1	The vccv disable keyword was added.
Release 3.7.0	These keywords were removed: control-word pw-static-label local remote vccv transport-mode
Release 4.2.1	The keyword tag-impose was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

A cross-connect may have two segments:

An Attachment Circuit (AC)
An second AC or a pseudowire

Note

The pseudowire is identified by two keys: neighbor and pseudowire ID. There may be multiple pseudowires going to the same neighbor. It is not possible to configure only a neighbor.

All L2VPN configurations can be deleted using the no l2vpn command.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

This example shows a point-to-point cross-connect configuration (including pseudowire configuration):


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn xconnect group l2vpn
RP/0/RP0/CPU0:router(config-l2vpn-xc)# p2p rtrA_to_rtrB
RP/0/RP0/CPU0:router(config-xc-p2p)# neighbor 10.1.1.2 pw-id 1000 pw-class class12
RP/0/RP0/CPU0:router(config-xc-p2p)# neighbor 10.1.1.3 pw-id 1001 pw-class class13
RP/0/RP0/CPU0:router(config-xc)# p2p rtrC_to_rtrD
RP/0/RP0/CPU0:router(config-xc-p2p)# neighbor 10.2.2.3 pw-id 200 pw-class class23
RP/0/RP0/CPU0:router(config-xc-p2p)# neighbor 10.2.2.4 pw-id 201 pw-class class24

This example shows a point-to-point cross-connect configuration (including pseudowire configuration):


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn xconnect group l2vpn
RP/0/RP0/CPU0:router(config-l2vpn-xc)# p2p rtrA_to_rtrB
RP/0/RP0/CPU0:router(config-xc-p2p)# neighbor 10.1.1.2 pw-id 1000 pw-class foo
RP/0/RP0/CPU0:router(config-xc)# p2p rtrC_to_rtrD
RP/0/RP0/CPU0:router(config-xc-p2p)# neighbor 20.2.2.3 pw-id 200 pw-class bar1

Related Commands

Command	Description
l2vpn	Enters L2VPN configuration mode.
p2p	Enters p2p configuration submode to configure point-to-point cross-connects.
pw-class (L2VPN)	Enters pseudowire class submode to define a pseudowire class template.
xconnect group	Configures cross-connect groups.

neighbor evpn

To enable EVPN-VPWS endpoint on the p2p cross-connect, use the neighbor evpn command in the p2p configuration submode.

neighbor evpn evi vpn-idtarget ac-id

Syntax Description


evi `vpn-id`	Virtual Private Network Identifier where this p2p xconnect is setup.
target `ac-id`	Specifies the targeted remote attachment circuit id of the EVPN.

Command Default

None

Command Modes

p2p configuration submode

Command History


Release	Modification
Release 6.0.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operation
l2vpn	read, write

Examples

The following example shows how to enable EVPN-VPWS endpoint on the p2p cross-connect.

RP/0/RSP0/CPU0:router# configure
RP/0/RSP0/CPU0:routerRP/0/RP00RSP0/CPU0:router# interface TenGigE0/1/0/12
RP/0/RSP0/CPU0:router(config)# l2vpn
RP/0/RSP0/CPU0:router(config-l2vpn)# xconnect group xc1
RP/0/RSP0/CPU0:router(config-l2vpn-xc)# p2p vpws
RP/0/RSP0/CPU0:router(config-l2vpn-xc-p2p)# interface gigabitethernet 0/1/0/9
RP/0/RSP0/CPU0:router(config-l2vpn-xc-p2p)# neighbor evpn evi 100 target 80

nsr (L2VPN)

To configure non-stop routing, use the nsr command in L2VPN configuration submode. To return to the default behavior, use the no form of this command.

nsr

no nsr

Syntax Description

This command has no keywords or arguments.

Command Default

None

Command Modes

L2VPN configuration submode

Command History


Release	Modification
Release 4.3.0	This command was introduced.

Usage Guidelines

All L2VPN configuration can be deleted using the no l2vpn command.

Note

NSR is enabled by default for L2VPN On Cisco IOS XR 64 bit operating system. You cannot configure the nsr command under L2VPN configuration submode.

Task ID


Task ID	Operation
l2vpn	read, write

Examples

The following example shows how to configure non-stop routing:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# nsr

Related Commands

Command	Description
l2vpn	Enters L2VPN configuration mode.

option-b-asbr-only

To enter option-b-asbr-only configuration mode, use the option-b-asbr-only command under the address-family L2VPN EVPN global configuration mode.

option-b-asbr-only

Syntax Description


option-b-asbr-only	Enables Inter-AS option-B for L2VPN EVPN address-family identifier (AFI) and subsequent address-family identifier (SAFI).

Syntax Description

This command has no keywords or arguments.

Command Default

None.

Command Modes

Global configuration mode

Command History


Release	Modification
Release 7.4.1	This command was introduced.

Usage Guidelines

No specific guidelines impact the use of this command.

Examples

This example shows how to enable the ASBR router for option-B label exchange:


Router(config)# router bgp 300
Router(config-bgp)# address-family l2vpn evpn
Router(config-bgp-af)# option-b-asbr-only
Router(config-evpn-instance)# commit

password (L2TP)

To define the password and password encryption type for control channel authentication, use the password command in L2TP class configuration mode. To return to the default behavior, use the no form of this command.

password [0 | 7] password

no password

Syntax Description


0	(Optional) Specifies that an unencrypted password will follow.
7	(Optional) Specifies that an encrypted password will follow.
`password`	Unencrypted or clear text user password.

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Release 3.9.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to define an unencrypted password using the word “cisco” for control channel authentication:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2tp-class sanjose
RP/0/RP0/CPU0:router(config-l2tp-class)# password 0 cisco

Related Commands

Command	Description
authentication (L2TP)	Enables L2TP authentication for a specified L2TP class name.
hello-interval (L2TP)	Configures the hello-interval value for L2TP (duration between control channel hello packets).
hidden (L2TP)	Enables hidden attribute-value pairs (AVPs).
hostname (L2TP)	Defines the name used in the L2TP hostname AVP.
l2tp-class	Enters L2TP class configuration mode where you can define an L2TP signaling template.
receive-window (L2TP)	Configures the receive window size for the L2TP server.
retransmit (L2TP)	Configures retransmit retry and timeout values.

preferred-path

To configure an MPLS TE tunnel to be used for L2VPN traffic, use the preferred-path command in Encapsulation MPLS configuration mode. To delete the preferred-path, use the no form of this command.

preferred-path interface { tunnel-ip | tunnel-te | } value [fallback disable]

no preferred-path interface { tunnel-ip | tunnel-te | } value [fallback disable]

Syntax Description


`interface`	Interface for the preferred path.
tunnel-ip	IP tunnel interface name for the preferred path.
`value`	Tunnel number for preferred path.
tunnel te	Specifies the TE tunnel interface name for the preferred path.

Command Default

None

Command Modes

Encapsulation MPLS configuration

Command History


Release	Modification
Release 3.6.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

The preferred-path command is applicable only to pseudowires with MPLS encapsulation.

Use the show l2vpn xconnect detail command to show the status of fallback (that is, enabled or disabled).

Note

All L2VPN configurations can be deleted using the no l2vpn command.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

This example shows how to configure preferred-path tunnel settings:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# pw-class kanata01
RP/0/RP0/CPU0:router(config-l2vpn-pwc)# encapsulation mpls
RP/0/RP0/CPU0:router(config-l2vpn-pwc-encap-mpls)# preferred-path interface tunnel-tp 345 
RP/0/RP0/CPU0:router(config-l2vpn-pwc-encap-mpls)# preferred-path interface tunnel-tp 345 fallback disable

Related Commands

Command	Description
show l2vpn xconnect	Displays brief information on configured cross-connects.

protocol l2tpv3

To configure Layer 2 Tunneling Protocol Version 3 (L2TPv3) as the signaling protocol for a pseudowire class, use the protocol l2tpv3 command in L2VPN pseudowire class encapsulation L2TPv3 configuration mode. To disable L2TPv3 as the signaling protocol for a pseudowire class, use the no form of this command.

protocol l2tpv3 [class class_name]

no protocol l2tpv3 [class class_name]

Syntax Description


class	Specifies the L2TPv3 class.
`class_name`	The L2TPv3 class name.

Command Default

None

Command Modes

L2VPN pseudowire class encapsulation L2TPv3 configuration

Command History


Release	Modification
Release 4.3.1	This command was introduced

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Note

All L2VPN configurations can be deleted using the no l2vpn command.

Task ID


Task ID	Operation
l2vpn	read, write

Examples

This example shows how to set the encapsulation and protocol to L2TPv3:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# pw-class kanata01
RP/0/RP0/CPU0:router(config-l2vpn-pwc)# encapsulation l2tpv3
RP/0/RP0/CPU0:router(config-l2vpn-pwc-l2tpv3)# protocol l2tpv3

Related Commands

Command	Description
pw-class (L2VPN)	Enters pseudowire class submode to define a pseudowire class template.
pw-class encapsulation l2tpv3	Configures L2TPv3 pseudowire encapsulation.

pw-class (L2VPN)

To enter pseudowire class submode to define a pseudowire class template, use the pw-class command in L2VPN configuration submode. To delete the pseudowire class, use the no form of this command.

pw-class class-name

no pw-class class-name

Syntax Description


`class-name`	Pseudowire class name.

Command Default

None

Command Modes

L2VPN configuration submode

Command History


Release	Modification
Release 3.5.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Note

All L2VPN configurations can be deleted using the no l2vpn command.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to define a simple pseudowire class template:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# xconnect group l1vpn
RP/0/RP0/CPU0:router(config-l2vpn-xc)# p2p rtrA_to_rtrB
RP/0/RP0/CPU0:router(config-l2vpn-xc-p2p)# neighbor 10.1.1.2 pw-id 1000
RP/0/RP0/CPU0:router(config-l2vpn-xc-p2p-pw)# pw-class kanata01

Related Commands

Command	Description
p2p	Enters p2p configuration submode to configure point-to-point cross-connects.

pw-class encapsulation l2tpv3

To configure L2TPv3 pseudowire encapsulation, use the pw-class encapsulation l2tpv3 command in L2VPN pseudowire class configuration mode. To return to the default behavior, use the no form of this command.

pw-class class name encapsulation l2tpv3 [cookie size {0 | 4 | 8} | ipv4 source address | pmtu max 68-65535 | protocol l2tpv3 class name | tos {reflect value 0-255 | value 0-255} | ttl value]

no pw-class class name encapsulation l2tpv3 [cookie size {0 | 4 | 8} | ipv4 source address | pmtu max 68-65535 | protocol l2tpv3 class name | tos {reflect value 0-255 | value 0-255} | ttl value]

Syntax Description


class name	Configures an encapsulation class name.
cookie size {0 \| 4 \| 8}	(Optional) Configures the L2TPv3 cookie size setting: 0—Cookie size is 0 bytes. 4—Cookie size is 4 bytes. 8—Cookie size is 8 bytes.
ipv4 source `address`	(Optional) Configures the local source IPv4 address.
pmtu max `68-65535`	(Optional) Configures the value of the maximum allowable session MTU.
protocol l2tpv3 class `name`	(Optional) Configures L2TPv3 as the signaling protocol for the pseudowire class.
tos {reflect value `0-255` \| value `0-255`}	(Optional) Configures TOS and the TOS value. Range is 0 to 255.
ttl `value`	Configures the Time-to-live (TTL) value. Range is 1 to 255.

Command Default

None

Command Modes

L2VPN pseudowire class configuration

Command History


Release	Modification
Release 3.9.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Note

All L2VPN configurations can be deleted using the no l2vpn command.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to define L2TPV3 pseudowire encapsulation:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# pw-class kanata01
RP/0/RP0/CPU0:router(config-l2vpn-pwc)# encapsulation l2tpv3

The following example shows how to set the encapsulation and protocol to L2TPV3:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# pw-class kanata01
RP/0/RP0/CPU0:router(config-l2vpn-pwc)# encapsulation l2tpv3
RP/0/RP0/CPU0:router(config-l2vpn-pwc-l2tpv3)# protocol l2tpv3

Related Commands

Command	Description
pw-class (L2VPN)	Enters pseudowire class submode to define a pseudowire class template.
pw-class encapsulation mpls	Configures MPLS pseudowire encapsulation.

pw-class encapsulation mpls

To configure MPLS pseudowire encapsulation, use the pw-class encapsulation mpls command in L2VPN pseudowire class configuration mode. To undo the configuration, use the no form of this command.

pw-class class-name encapsulation mpls {control word | ipv4 | load-balancing flow-label | preferred-path | protocol ldp | sequencing | tag-rewrite | transport-mode | vccv verification-type none}

no pw-class class-name encapsulation mpls {control word | ipv4 | load-balancing flow-label | preferred-path | protocol ldp | sequencing | tag-rewrite | transport-mode | vccv verification-type none}

Syntax Description


`class-name`	Encapsulation class name.
control word	Disables control word for MPLS encapsulation. Disabled by default.
ipv4	Sets the local source IPv4 address.
load-balancing flow-label	Sets flow label-based load balancing.
preferred-path	Configures the preferred path tunnel settings.
protocol ldp	Configures LDP as the signaling protocol for this pseudowire class.

sequencing	Configures sequencing on receive or transmit.
tag-rewrite	Configures VLAN tag rewrite.
transport-mode	Configures transport mode to be either Ethernet or VLAN.
vccv none	Enables or disables the VCCV verification type.

Command Default

None

Command Modes

L2VPN pseudowire class configuration

Command History


Release	Modification
Release 3.5.0	This command was introduced.
Release 3.8.0	The keywords control word disable and vccv none were replaced by the keywords control word and vccv verification-type none .
Release 3.9.0	The following keywords were added: preferred-path sequencing tag-rewrite transport-mode
Release 4.3.0	The keyword load-balancing flow-label was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Note

All L2VPN configurations can be deleted using the no l2vpn command.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

This example shows how to define MPLS pseudowire encapsulation:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# pw-class kanata01 
RP/0/RP0/CPU0:router(config-l2vpn-pwc)# encapsulation mpls

Related Commands

Command	Description
pw-class (L2VPN)	Enters pseudowire class submode to define a pseudowire class template.
pw-class encapsulation l2tpv3	Configures L2TPv3 pseudowire encapsulation.

pw-ether

To configure a PWHE Ethernet interface, use the pw-ether command in global configuration mode or in p2p configuration submode. To return to the default behavior, use the no form of this command.

pw-ether value

no pw-ether value

Syntax Description


`value`	Value of the PWHE Ethernet interface. The range is from 1 to 32768.

Command Default

None

Command Modes

Global configuration

p2p configuration

Command History


Release	Modification
Release 4.2.1	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operation
interface (global configuration)	read, write
l2vpn (p2p configuration)	read, write

Examples

This example shows the sample output of a PWHE Ethernet interface configuration in global configuration mode:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# interface pw-ether 78
RP/0/RP0/CPU0:router(config-if)#  attach generic-interface-list interfacelist1

This example shows the sample output of a PWHE Ethernet interface configuration in p2p configuration submode:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# xconnect group xc1
RP/0/RP0/CPU0:router(config-l2vpn-xc)#p2p grp1
RP/0/RP0/CPU0:router(config-l2vpn-xc-p2p)#interface pw-ether 78

This example shows the sample output of L2 overhead configuration for the PW-HE interface:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# interface pw-ether 78
RP/0/RP0/CPU0:router(config-if)# l2overhead 32

This example shows the sample output of Load-interval configuration for the PW-HE interface:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# interface pw-ether 78
RP/0/RP0/CPU0:router(config-if)# load-interval 60

This example shows the sample output of how to set logging of interface state change for the PW-HE interface:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# interface pw-ether 78
RP/0/RP0/CPU0:router(config-if)# logging events link-status

This example shows the sample output of MAC address configuration for the PW-HE interface:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# interface pw-ether 78
RP/0/RP0/CPU0:router(config-if)# mac-address 44-37-E6-89-C3-93

This example shows the sample output of MTU configuration for the PW-HE interface:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# interface pw-ether 78
RP/0/RP0/CPU0:router(config-if)# mtu 128

This example shows the sample output of bandwidth configuration for the PW-HE interface:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# interface pw-ether 78
RP/0/RP0/CPU0:router(config-if)# bandwidth 256

Related Commands

Command	Description
p2p	Enters p2p configuration submode to configure point-to-point cross-connects.

pw-grouping

To enable Pseudowire Grouping, use the pw-grouping command in L2vpn configuration submode. To return to the default behavior, use the no form of this command.

pw-grouping

no pw-grouping

Syntax Description


pw-grouping	Enables Pseudowire Grouping.

Command Default

PW-grouping is disabled by default.

Command Modes

L2VPN configuration submode

Command History


Release	Modification
Release 4.3.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operation
l2vpn	read, write

Examples

This example shows the sample output of pw-grouping configuration in L2VPN configuration submode:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# pw-grouping

Related Commands

Command	Description
l2vpn	Enters L2VPN configuration mode.
show l2vpn	Displays L2VPN information

pw-iw

To configure a PWHE IP Interworking interface, use the pw-iw command in p2p configuration submode. To return to the default behavior, use the no form of this command.

pw-iw value

no pw-iw value

Syntax Description


`value`	Value of the PWHE IP interface. The range is from 1 to 32768.

Command Default

None

Command Modes

p2p configuration

Command History


Release	Modification
Release 4.2.1	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operation
l2vpn	read, write

Examples

This example shows the sample output of a PWHE IP interface:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# xconnect group xc1
RP/0/RP0/CPU0:router(config-l2vpn-xc)#p2p grp1
RP/0/RP0/CPU0:router(config-l2vpn-xc-p2p)#interface pw-iw 78

Related Commands

Command	Description
pw-ether	Configures a Pseudowire Headend (PWHE) Ethernet interface.

p2p

To enter p2p configuration submode to configure point-to-point cross-connects, use the p2p command in L2VPN xconnect mode. To return to the default behavior, use the no form of this command.

p2p xconnect-name

no p2p xconnect-name

Syntax Description


`xconnect-name`	(Optional) Configures the name of the point-to-point cross- connect.

Command Default

None

Command Modes

L2VPN xconnect

Command History


Release	Modification
Release 3.4.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

The name of the point-to-point cross-connect string is a free format description string.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows a point-to-point cross-connect configuration (including pseudowire configuration):


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# xconnect group group 1
RP/0/RP0/CPU0:router(config-l2vpn-xc)# p2p xc1

Related Commands

Command	Description
interface (p2p)	Configures an attachment circuit.

receive-window (L2TP)

To configure the receive window size for the L2TP server, use the receive-window command in L2TP class configuration mode. To return to the default behavior, use the no form of this command.

receive-window size

no receive-window size

Syntax Description


`size`	Maximum number of packets that are received from a peer before back-off is applied. Default is 512.

Command Default

size : 512

Command Modes

L2TP class configuration

Command History


Release	Modification
Release 3.9.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to configure the receive window size for the L2TP server to 10 packets:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2tp-class cisco
RP/0/RP0/CPU0:router(config-l2tp-class)# receive-window 10

Related Commands

Command	Description
authentication (L2TP)	Enables L2TP authentication for a specified L2TP class name.
hello-interval (L2TP)	Configures the hello-interval value for L2TP (duration between control channel hello packets).
hidden (L2TP)	Enables hidden attribute-value pairs (AVPs).
hostname (L2TP)	Defines the name used in the L2TP hostname AVP.
l2tp-class	Enters L2TP class configuration mode where you can define an L2TP signaling template.
password (L2TP)	Defines the password and password encryption type for control channel authentication.
retransmit (L2TP)	Configures retransmit retry and timeout values.

retransmit (L2TP)

To configure retransmit retry and timeout values, use the retransmit command in L2TP class configuration mode. To return to the default behavior, use the no form of this command.

retransmit {initial initial-retries | retries retries | timeout {max | min} timeout}

no retransmit {initial initial-retries | retries retries | timeout {max | min} timeout}

Syntax Description


initial `initial-retries`	Configures the number of SCCRQ messages resent before giving up on a particular control channel. Range is 1 to 1000. Default is 2.
retries `retries`	Configures the maximum number of retransmissions before determining that peer router does not respond. Range is 5 to 1000. Default is 15.
timeout {max \| min} `timeout`	Configures the maximum and minimum retransmission interval in seconds for control packets. Range is 1 to 8. Maximum timeout default is 8 seconds. Minimum timeout default is 1 second.

Command Default

initial retries : 2

retries : 15

min timeout: 1

max timeout: 8

Command Modes

L2TP class configuration

Command History


Release	Modification
Release 3.9.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to configure a retransmit retry value to 1:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2tp-class cisco
RP/0/RP0/CPU0:router(config-l2tp-class)# retransmit initial retries 1

Related Commands

Command	Description
authentication (L2TP)	Enables L2TP authentication for a specified L2TP class name.
hello-interval (L2TP)	Configures the hello-interval value for L2TP (duration between control channel hello packets).
hidden (L2TP)	Enables hidden attribute-value pairs (AVPs).
hostname (L2TP)	Defines the name used in the L2TP hostname AVP.
l2tp-class	Enters L2TP class configuration mode where you can define an L2TP signaling template.
password (L2TP)	Defines the password and password encryption type for control channel authentication.
receive-window (L2TP)	Configures the receive window size for the L2TP server.

rollover (L3VPN)

To configure rollover times for a tunnel-template, use the rollover command in tunnel encapsulation l2tp configuration mode. To return to the default behavior, use the no form of this command.

rollover periodic time holdown time

no rollover periodic time holdown time

Syntax Description


periodic `time`	Configures the periodic rollover time in seconds. Range is 60 to 31536000.
holddown`time`	Configures the holddown time for old session cookie values.

Command Default

None

Command Modes

tunnel encapsulation l2tp configuration

Command History


Release	Modification
Release 3.5.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

The name of the point-to-point cross-connect string is a free format description string.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to configure rollover times for a tunnel-template:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# tunnel-template kanata_9
RP/0/RP0/CPU0:router(config-tuntem) encapsulation l2tp
RP/0/RP0/CPU0:router(config-tunencap-l2tp)# rollover

Related Commands

Command	Description
interface (p2p)	Configures an attachment circuit.

show bgp l2vpn evpn

To display BGP routes associated with EVPN under L2VPN address family, use the show bgp l2vpn evpn command in EXEC mode.

show bgp l2vpn evpn {bridge-domain bridge-domain-name | rd {all | IPv4 address:nn| 4-byte as-number:nn| 2-byte as-number:nn}}

Syntax Description


bridge-domain `bridge-domain-name`	Displays the bridges by the bridge ID. The bridge-domain-name argument is used to name a bridge domain.
rd	Displays routes with specific route distinguisher.
all	Displays specified routes in all RDs.
`IPv4 address:nn`	Specifies the IPv4 address of the route distinguisher. nn: 16-bit number
`4-byte as-number:nn`	Specifies 4-byte AS number in asdot (X.Y) format or in asplain format. For 4-byte AS number in asdot (X.Y) format, the range is from 1 to 65535. The format is: <1-65535>.<0-65535>:<0-65535> For 4-byte AS number in asplain format, the range is from 65536 to 4294967295. The format is: <65536-4294967295>: nn: 32-bit number
`2-byte as-number:nn`	Specifies 2-byte as-number. The range is from 1 to 65535. nn: 32-bit number

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 6.1.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operation
bgp	read

Examples

This sample output shows the BGP routes associated with EVPN with bridge-domain filter:

show bgp l2vpn evpn bridge-domain bd1 
Network            Next Hop            Metric LocPrf Weight Path
Route Distinguisher: 192.0.2.1:1 (default for vrf bd1)
*>i[1][0077.0000.0000.0000.0001][0]/120
                      198.51.100.1                  100      0 i
*>i[1][0077.0000.0000.0000.0001][4294967295]/120
                      198.51.100.1                  100      0 i
*>i[1][0088.0000.0000.0000.0001][0]/120
                      203.0.113.1                   100      0 i
* i                   209.165.200.225               100      0 i
*>i[1][0088.0000.0000.0000.0001][4294967295]/120
                      203.0.113.1                   100      0 i
* i                   209.165.200.225               100      0 I
*  [2][0][48][0001.0000.0001][0]/104
*>                    209.165.201.1                          0 101 i
*>i[2][0][48][0002.0000.0001][0]/104
                      203.0.113.1                   100      0 102 i
* i                   209.165.200.225               100      0 102 i
*>i[3][0][32][203.0.113.1]/80
                      203.0.113.1                   100      0 i
*>i[3][0][32][209.165.200.225]/80
                      209.165.200.225               100      0 i

show bgp vrf-db

To display the BGP VRF database information, use the show bgp vrf-db command in the EXEC mode.

show bgp vfr-db {all | vrf table id}

Syntax Description


all	Displays all BGP VRF database table information.
`vrf table id`	Displays the BGP VRF database information for the specific VRF table ID.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 6.1.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operation
l2vpn	read

Examples

This sample output shows the BGP VRF database information with the VRF table ID filter:

#show bgp vrf-db table 0x00000001
Tue Jun 14 14:39:32.468 EDT

VRF-TBL: bd1 (L2VPN EVPN)
  TBL ID: 0x00000001
  RSI Handle: 0x0 
  Refcount: 24
  Import:
    RT-List: RT:100:1
    Stitching RT-List: RT:101:1
  Export:
    RT-List: RT:100:1
    Stitching RT-List: RT:101:1

show evpn evi ead

To display the EVPN E-VPN ID information, use the show evpn evi ead command in the EXEC mode.

show evpn evi ead detail

Syntax Description


evi	Specifies the EVPN Instance Identifier. This is used to derive the default Route Distinguisher and Route Targets.
ead	Specifies the EVPN ead routes.
detail	Displays detailed information.

Command Default

None.

Command Modes

EXEC

Command History


Release	Modification
Release 6.0.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operation
l2vpn	read

Examples

This sample output shows the EVPN EVI detailed information:


RP/0/RP0/CPU0:router#show evpn evi ead detail
Mon Apr 18 13:19:44.311 EDT

EVI   Ethernet Segment Id      EtherTag Nexthop                                 Label   
----- ------------------------ -------- --------------------------------------- --------
1     00a1.a2a3.a4a5.a6a7.a8a9 0        ::                                      24006   
                                        2.2.2.2                                 24007   
   Source: Local, Remote, MPLS, VXLAN
1     00a1.a2a3.a4a5.a6a7.a8a9 ffffffff 2.2.2.2                                 0       
   Source: Remote, Unknown encap
200   0000.0000.0000.0000.0000 1        ::                                      24025   
   Source: Local, MPLS
200   0000.0000.0000.0000.0000 4        ::                                      24026   
   Source: Local, MPLS
200   0000.0000.0000.0000.0000 11       ::                                      24027   
   Source: Local, MPLS
300   00a1.a2a3.a4a5.a6a7.a8a9 0        ::                                      24004   
                                        2.2.2.2                                 24005   
   Source: Local, Remote, MPLS, VXLAN
300   00a1.a2a3.a4a5.a6a7.a8a9 ffffffff 2.2.2.2                                 0       
   Source: Remote, Unknown encap
302   00a1.a2a3.a4a5.a6a7.a8a9 0        ::                                      24008   
   Source: Local, MPLS, VXLAN
400   00b1.b2b3.b4b5.b6b7.b8b9 0        ::                                      24010   
   Source: Local, MPLS

Related Commands

Command	Description
evpn	Enters EVPN configuration mode.
evi	Enters the EVPN EVI configuration mode to configure optional BGP settings for a bridge domain or EVI.

show evpn internal-label

To display EVPN internal label associated configuration information, use the show evpn internal-label command in the EXEC mode.

show evpn internal-label [vpn-id evi [detail]]

Syntax Description


vpn-id `evi`	Displays information for a specified E-VPN Identifier.
detail	Displays detailed information.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 6.1.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operation
l2vpn	read

Examples

This sample output shows the EVPN internal label associated configuration information.

show evpn internal-label vpn-id 1 detail 
Tue Jun 14 16:18:51.563 EDT

EVI   Ethernet Segment Id                     EtherTag Label   
----- --------------------------------------- -------- --------
1     0088.0000.0000.0000.0001                0        24036   
   Multi-paths resolved: TRUE
   Multi-paths local label: 24036     
   Pathlists:
      MAC     1 entries
      EAD/ES  203.0.113.1                              0              
              209.165.200.225                          0              
      EAD/EVI 203.0.113.1                              24001          
              209.165.200.225                          24001          
      Summary 203.0.113.1                              24001          
              209.165.200.225                          24001

show dci-fabric-interconnect

To display the DCI fabric tenant interconnect information, use the show dci-fabric-interconnect command in the EXEC mode.

show dci-fabric-interconnect {auto-configuration-pools | dci-vrf-db [vrf vrfname] | fabric [fabric id | opflex-session] | fabric-vrf-db [fabric fabric id]}

Syntax Description


auto-configuration-pools	Displays auto configuration pool parameters.
dci-vrf-db	Displays DCI VRF database information.
vrf`vrf name`	Displays DCI VRF database for a specific VRF.
fabric `fabric id`	Displays fabric information for fabric ID. The range is from 1000 to 9999.
opflex-session	Displays opflex session information.
fabric-vrf-db	Displays fabric VRF database information.
fabric `fabric id`	Displays fabric VRF database for a fabric ID.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 6.1.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operation
l2vpn	read

Examples

This sample output shows the DCI fabric interconnect information with the auto-configuration-pools filter:

RP/0/RP0/CPU0:router# show dci-fabric-interconnect auto-configuration-pools
Sat May 28 08:12:24.192 PDT
Auto Configuration Pool Info
--------------------------------------------------
Pool:Min-Max          Used Num Bits    Used Range
--------------------------------------------------
VNI-Pool:0001-1000    Used:10          Used:1-10
BD-Pool :0001-1000    Used:10          Used:1-10
BVI-Pool:0001-1000    Used:10          Used:1-10
--------------------------------------------------

Examples

This sample output shows the DCI fabric interconnect information with the fabric opflex-session filter:

RP/0/RP0/CPU0:router# show dci-fabric-interconnect fabric opflex-session
Sat May 28 08:12:09.326 PDT
Fabric Id: 1000
State: Config Complete(Sat May 28 08:09:01.813 PDT)
       Active (Healthy)(Wed Dec 31 16:00:00.000 PST)

Peers:
Peer-IP            Peer-Port    Peer-Status /Timestamp
===============    =========    ==========================================
209.165.200.225    8009         Ready     /(Wed Dec 31 16:00:01.000 PST)
==========================================================================

Examples

This sample output shows the DCI fabric interconnect information with the fabric-vrf-db filter:

RP/0/RP0/CPU0:router# show dci-fabric-interconnect fabric-vrf-db
Tue Jul 26 16:13:30.101 PDT
Flags: S = STALE
---------------------------------------------------------------------------
Fabric Id: 1000  Number of VRFs: 0010
---------------------------------------------------------------------------
Fabric-VRF:FV1000_2  DCI VRF:DV2  Flags:
         v4 Import RTs:(100:19333144)
         v4 Export RTs:(100:19333144)
         v6 Import RTs:(100:19333144)
         v6 Export RTs:(100:19333144)

Fabric-VRF:FV1000_3  DCI VRF:DV3  Flags:
         v4 Import RTs:(100:19333144)
         v4 Export RTs:(100:19333144)
         v6 Import RTs:(100:19333144)
         v6 Export RTs:(100:19333144)

Fabric-VRF:FV1000_4  DCI VRF:DV4  Flags:
         v4 Import RTs:(100:19333144)
         v4 Export RTs:(100:19333144)
         v6 Import RTs:(100:19333144)
         v6 Export RTs:(100:19333144)

Fabric-VRF:FV1000_5  DCI VRF:DV5  Flags:
         v4 Import RTs:(100:19333144)
         v4 Export RTs:(100:19333144)
         v6 Import RTs:(100:19333144)
         v6 Export RTs:(100:19333144)

Examples

This sample output shows the DCI fabric interconnect information with the dci-vrf-db filter:

RP/0/RP0/CPU0:router# show  dci-fabric-interconnect dci-vrf-db
Sat May 28 08:12:17.401 PDT
Flags: AP = ADD_PENDING, DP = DELETE_PENDING, C = CONFIG_APPLIED, S = STALE
---------------------------------------------------------------------------
DCI VRF:DV6  Flags:C
         Number of Fabric VRFs: 0002
         Fabric VRFs: (1000,FV1000_6); (2000,FV2000_6)
         v4 RT: (Import:1000:1000, Export:         )/Flags:C
                (Import:1000:2000, Export:         )/Flags:C
         v6 RT: (Import:2000:1000, Export:         )/Flags:C
                (Import:2000:2000, Export:         )/Flags:C
         VNI Id:0007 ; BD-Name:fti-bd-7
         BVI-ID:0007 ; BVI-IP:169.254.1.30 ; BVI-IPV6: Enabled
---------------------------------------------------------------------------
DCI VRF:DV7  Flags:C
         Number of Fabric VRFs: 0002
         Fabric VRFs: (1000,FV1000_7); (2000,FV2000_7)
         v4 RT: (Import:1000:1000, Export:         )/Flags:C
                (Import:1000:2000, Export:         )/Flags:C
         v6 RT: (Import:2000:1000, Export:         )/Flags:C
                (Import:2000:2000, Export:         )/Flags:C
         VNI Id:0008 ; BD-Name:fti-bd-8
         BVI-ID:0008 ; BVI-IP:169.254.1.30 ; BVI-IPV6: Enabled
---------------------------------------------------------------------------

show generic-interface-list

To display information about interface-lists, use the show generic-interface-list in EXEC mode.

show generic-interface-list [ location | name | retry | standby ]

Syntax Description


location	(Optional) Displays information about interface-lists for the specified location.
name	(Optional) Displays information about interface-lists for the specified interface list name.
retry	(Optional) Displays retry-list information.
standby	(Optional) Displays Standby node specific information.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 4.3.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operation
l2vpn	read

Examples

The following example displays output for the show generic-interface-list command:


RP/0/RP0/CPU0:router# show generic-interface-list
				Thu Aug  2 13:48:57.462 CDT
				generic-interface-list: nsrIL (ID: 1, interfaces: 2)
				   Bundle-Ether2 - items pending 0, downloaded to FIB
				   GigabitEthernet0/0/0/1 - items pending 0, downloaded to FIB
				 Number of items: 400
				 List is downloaded to FIB

The following example displays output for the show generic-interface-list retry private command:


RP/0/RP0/CPU0:router# show generic-interface-list retry private
				Thu Aug  2 14:20:42.883 CDT
				total: 0 items

The following example displays output for the show generic-interface-list standby command:


RP/0/RP0/CPU0:router# show generic-interface-list standby
				Thu Aug 2 14:25:01.749 CDT
				generic-interface-list: nsrIL (ID: 0, interfaces: 2)
				Bundle-Ether2 - items pending 0, NOT downloaded to FIB
				GigabitEthernet0/0/0/1 - items pending 0, NOT downloaded to FIB
				Number of items: 0
				List is not downloaded to FIB

Related Commands

Command	Description
l2vpn	Enters L2VPN configuration mode.

show l2tp class

To display information about an L2TP class, use the show l2tp class command in EXEC mode.

show l2tp class name name

Syntax Description


name `name`	Configures an L2TP class name.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 3.9.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows sample output for the show l2vtp session class command:


RP/0/RP0/CPU0:router# show l2tp class name kanata_02

l2tp-class kanata_02
  manually configured class
  configuration parameters:
     (not) hidden
     (no) authentication
     (no) digest
     digest check enable
     hello 60
     (no) hostname
     (no) password
     (no) accounting
     (no) security crypto-profile
     (no) ip vrf
     receive-window 888
     retransmit retries 15
     retransmit timeout max 8
     retransmit timeout min 1
     retransmit initial retries 2
     retransmit initial timeout max 8
     retransmit initial timeout min 1
     timeout setup 300

This table describes the significant fields shown in the display.

Table 1. show l2tp class brief Field Descriptions
Field	Description
l2tp-class	Shows the L2TP class name and the manner of its creation. For example, manually configured class.
configuration parameters	Displays a complete list and state of all configuration parameters.

Related Commands

Command	Description
l2tp-class	Enters L2TP class configuration mode where you can define an L2TP signaling template.

show l2tp counters forwarding session

To display L2TP forward session counters, use the show l2tp counter forwarding session command in EXEC mode.

show l2tp counters forwarding session [id identifier | name local-name remote-name]

Syntax Description


id `identifier`	(Optional) Configures the session counter identifier.
name `local-name remote name`	(Optional) Configures the local and remote names for a session counter.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 3.9.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows sample output for the show l2tp counters forwarding session command:


RP/0/RP00/CPU0:router(config-l2vpn)# pw-class kanata01show l2tp counters forwarding session 

LocID      RemID      TunID      Pkts-In    Pkts-Out   Bytes-In   Bytes-Out
22112      15584      14332          0          0          0          0

This table describes the significant fields shown in the display.

Table 2. show l2tp counters forwarding session Field Descriptions
Field	Description
LocID	Local session ID.
RemID	Remote session ID.
TunID	Local Tunnel ID for this session.
Pkts-In	Number of packets input in the session.
Pkts-Out	Number of packets output in the session.
Bytes-In	Number of bytes input in the session.
Bytes-Out	Number of bytes output in the session.

Related Commands

Command	Description

show l2tp session

To display information about L2TP sessions, use the show l2tp session command in EXEC mode.

show l2tp session [detail | brief | interworking | circuit | sequence | state] {id id | name name}

Syntax Description


brief	(Optional) Displays summary output for a session.
circuit	(Optional) Displays attachment circuit information for a session.
detail	(Optional) Displays detailed output for a session.
interworking	(Optional) Displays interworking information for a session.
sequence	(Optional) Displays data packet sequencing information for a session.
state	(Optional) Displays control plane state information for a session.
id `id`	Configures the local tunnel ID. Range is 0 to 4294967295.
name `name`	Configures the tunnel name.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 3.9.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following sample output is from the show l2tp session brief command:


RP/0/RP00/CPU0:router(config-l2vpn-pw)# show l2tp session brief
Tue Jun 10 12:51:30.901 UTC
LocID      TunID      Peer-address    State     Username, Intf/sess/cir  Vcid, Circuit                   
1606803058 1487464659 26.26.26.26     est,UP    101, Gi0/2/0/1.101              
3663696887 1487464659 26.26.26.26     est,UP    100, Gi0/2/0/1.100

This table describes the significant fields shown in the display.

Table 3. show l2tp session brief Field Descriptions
Field	Description
LocID	Local session ID.
TunID	Local tunnel ID for this session.
Peer-address	The IP address of the other end of the session.
State	The state of the session.
Vcid	The Virtual Circuit ID of the session. This is the same value of the pseudowire ID for l2vpn.

The following sample output is from the show l2tp session detail command:


RP/0/RP00/CPU0:router(config-l2vpn-pw)# show l2tp session detail 
Tue Jun 10 12:53:19.842 UTC
Session id 1606803058 is up, tunnel id 1487464659, logical session id 131097
  Remote session id is 2602674409, remote tunnel id 2064960537
  Remotely initiated session
Call serial number is 4117500017
Remote tunnel name is ASR9K-PE2
  Internet address is 26.26.26.26:1248
Local tunnel name is PRABHRAM-PE1
  Internet address is 25.25.25.25:4272
IP protocol 115
  Session is L2TP signaled
  Session state is established, time since change 00:07:28
  UDP checksums are disabled
  Session cookie information:
    local cookie, size 4 bytes, value 6d 3e 03 67 
    remote cookie, size 4 bytes, value 0d ac 7a 3b 
  Tie breaker is 0xfee65781a2fa2cfd, enabled TRUE.
  Sequencing is off
  Conditional debugging is disabled
  Unique ID is 101
Session Layer 2 circuit
  Payload type is Ethernet, Name is GigabitEthernet0_2_0_1.101
  Session vcid is 101
  Circuit state is UP
    Local circuit state is UP
    Remote circuit state is UP

Related Commands

Command	Description

show l2tp tunnel

To display information about L2TP tunnels, use the show l2tp tunnel command in EXEC mode.

show l2tp tunnel {detail | brief | state | transport} {id identifier | name local-name remote-name}

Syntax Description


detail	Displays detailed output for L2TP tunnels.
brief	Displays summary information for the tunnel.
state	Displays control plane state information.
transport	Displays transport information (IP) for each selected control channel.
id `identifier`	Displays local control channel identifiers.
name `local-name remote-name`	Displays the local and remote names of a control channel.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 3.9.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following sample output is from the show l2tp tunnel brief command:

RP/0/RP0/CPU0:router(config-l2vpn-encap-mpls)# show l2tp tunnel brief
Tue Jun 10 12:46:04.421 UTC
LocTunID   RemTunID   Remote Name   State  Vrf Name    Remote Address  Sessn L2TP Class/Count VPDN Group 
1487464659 2064960537 ASR9K-PE2     est                26.26.26.26     2     L2TPV3_CLASS

This table describes the significant fields shown in the display.

Table 4. show l2tp tunnel Field Descriptions
Field	Description
LocTunID	Local session ID.
RemTunID	Remote session ID.
Remote Name	Remote name of the session.
State	State of the session.
Remote Address	Remote address of the session.
Port	Session port.
Sessions	Number of sessions.
L2TP	L2TP class name.

The following sample output is from the show l2tp tunnel detail command:

RP/0/RP0/CPU0:router(config-l2vpn-encap-mpls)# show l2tp tunnel detail
Tue Jun 10 12:47:36.638 UTC
Tunnel id 1487464659 is up, remote id is 2064960537, 2 active sessions
  Remotely initiated tunnel
  Tunnel state is established, time since change 4d19h
  Tunnel transport is IP  (115)
  Remote tunnel name is ASR9K-PE2
    Internet Address 26.26.26.26, port 0
  Local tunnel name is PRABHRAM-PE1
    Internet Address 25.25.25.25, port 0
  VRF table id is 0xe0000000
  Tunnel group id 
  L2TP class for tunnel is L2TPV3_CLASS
  Control Ns 4178, Nr 4181
  Local RWS 512 (default), Remote RWS 512
  Control channel Congestion Control is disabled
  Tunnel PMTU checking disabled
  Retransmission time 1, max 1 seconds
  Unsent queuesize 0, max 0
  Resend queuesize 0, max 1
  Total resends 0, ZLB ACKs sent 4177
  Total out-of-order dropped pkts 0 
  Total out-of-order reorder pkts 0 
  Total peer authentication failures 0
  Current no session pak queue check 0 of 5
  Retransmit time distribution: 0 0 0 0 0 0 0 0 0 
  Control message authentication is disabled

Related Commands

Command	Description
show l2tp session	Displays information about L2TP sessions.

show l2vpn

To display L2VPN information, use the show l2vpn command in EXEC mode.

show l2vpn

Syntax Description

This command has no keywords or arguments.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 4.3.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operation
l2vpn	read

Examples

The following example displays output for the show l2vpn command. The output provides an overview of the state of the globally configured features.


RP/0/RP0/CPU0:router# show l2vpn
	Mon May  7 15:01:17.963 BST
	PW-Status: disabled
	PW-Grouping: disabled
	Logging PW: disabled
	Logging BD state changes: disabled
	Logging VFI state changes: disabled
	Logging NSR state changes: disabled
	TCN propagation: disabled
	PWOAMRefreshTX: 30s

Related Commands

Command	Description
l2vpn	Enters L2VPN configuration mode.
pw-grouping	Enables Pseudowire Grouping

show l2vpn atom-db

To display AToM database information, use the show l2vpn atom-db command in EXEC mode.

Syntax Description


detail	Specifies the details of the database.
l2-rid	Specifies the AToM database walking the L2 RID thread.
ldp-rid	Specifies the AToM database walking the LDP RID thread.
local-gid	Specifies the AToM database walking the Local GID thread.
neighbor	Specifies the details of the neighbor database.
preferred-path	Specifies the preferred path (tunnel) of the database
remote-gid	Specifies the AToM database walking the Remote GID thread.
source	Specifies the details of the source database.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 4.2.1	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read

Examples

This example shows the sample output of the show l2vpn atom-db source 10.0.0.1 command:


RP/0/RP0/CPU0:router# show l2vpn atom-db source 10.0.0.1
Peer ID         Source        VC ID      Encap    Signaling   FEC     Discovery 
172.16.0.1         10.0.0.1       1          MPLS     LDP         128     none

This example shows the sample output of the show l2vpn atom-db source 10.0.0.1 detail command:

RP/0/RP0/CPU0:router# show l2vpn atom-db source 10.0.0.1 detail
  PW: neighbor 172.16.0.1, PW ID 1, state is down ( provisioned )
    PW class class1, XC ID 0x1
    Encapsulation MPLS, protocol LDP
    Source address 10.0.0.1
    PW type Ethernet, control word disabled, interworking none
    PW backup disable delay 0 sec
    Sequencing not set

      MPLS         Local                          Remote                        
      ------------ ------------------------------ -----------------------------
      Label        16000                          unknown                       
      Group ID     0x20000060                     0x0                           
      Interface    GigabitEthernet0/0/0/1.1       unknown                       
      MTU          1504                           unknown                       
      Control word disabled                       unknown                       
      PW type      Ethernet                       unknown                       
      VCCV CV type 0x2                            0x0                           
                                                  (none)                        
                   (LSP ping verification)                                      
      VCCV CC type 0x6                            0x0                           
                                                  (none)                        
                   (router alert label)                                         
                   (TTL expiry)                                                 
      ------------ ------------------------------ -----------------------------
    MIB cpwVcIndex: 4278194081
    Create time: 13/12/2010 15:28:26 (20:32:27 ago)
    Last time status changed: 13/12/2010 15:28:26 (20:32:27 ago)
    Configuration info:
      PW class: class1
      Peer ID = 172.16.0.1, pseudowire ID = 1
      Control word is not set
      Transport mode: not set
        Configured (Static) Encapsulation: not set
        Provisioned Encapsulation: MPLS
      Static tag rewrite: not set
      MTU: 1504
      Tunnel interface: None
      IW type: 0
      PW type: Dynamic
      Pref path configured: No
      Bridge port: No
      BP learning disabled: No
      BP ucast flooding disabled: No
      BP bcast flooding disabled: No
      CW is mandatory: No
      Label: local unassigned, remote unassigned
      L2 Router-ID: 0.0.0.0
      LDP Router-ID: 0.0.0.0
      GR stale: No
    LDP Status: local established, remote unknown
    LDP tag rewrite: not set
    Force switchover: inactive
    MAC trigger: inactive
    VC sane: Yes
    Use PW Status: No
    Local PW Status: Up(0x0); Remote PW Status: Up(0x0)
    Peer FEC Failed: No
    LSP: Down
    Operational state: 
      LDP session state: down
      TE tunnel transport: No
      VC in gr mode: No
      Peer state: up
      Transport LSP down: Yes
      Advertised label to LDP: No
      Received a label from LSD: Yes
      Need to send standby bit: No
      VC created from rbinding: No
      PW redundancy dampening on : No
      Notified up : No
    Detailed segment state: down
     PW event trace history [Total events: 8]
     -----------------------------------------
     Time                Event                          Value           
     ====                =====                          ===========     
     12/13/2010 15:28:26 LSP Down                       0         
     12/13/2010 15:28:26 Provision                      0         
     12/13/2010 15:28:26 LSP Down                       0         
     12/13/2010 15:28:26 Connect Req                    0         
     12/13/2010 15:28:26 Rewrite create                 0x100000  
     12/13/2010 15:28:26 Got label                      0x3e80    
     12/13/2010 15:28:26 Local Mtu                      0x5e0 
    12/13/2010 15:28:26 Peer Up                        0

show l2vpn collaborators

To display information about the state of the interprocess communications connections between l2vpn_mgr and other processes, use the show l2vpn collaborators command in EXEC mode.

show l2vpn collaborators

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 3.4.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows sample output for the show l2vpn collaborators command:


RP/0/RP0/CPU0:router# show l2vpn collaborators
L2VPN Collaborator stats:
Name                  State       Up Cnts      Down Cnts  
--------------------  ----------  -----------  -----------
IMC                    Down          0            0
LSD                    Up            1            0

This table describes the significant fields shown in the display.

Table 5. show l2vpn collaborators Field Descriptions
Field	Description
Name	Abbreviated name of the task interacting with l2vpn_mgr.
State	Indicates if l2vpn_mgr has a working connection with the other process.
Up Cnts	Number of times the connection between l2vpn_mgr and the other process has been successfully established.
Down Cnts	Number of times that the connection between l2vpn_mgr and the other process has failed or been terminated.

Related Commands

Command	Description
clear l2vpn collaborators	Clears the state change counters for L2VPN collaborators.

show l2vpn database

To display L2VPN database, use the show l2vpn database command in EXEC mode.

show l2vpn database {ac | node}

Syntax Description


ac	Displays L2VPN Attachment Circuit (AC) database
node	Displays L2VPN node database.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 4.3.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Even when xSTP (extended spanning tree protocol) operates in the PVRST mode, the output of the show or debug commands flag prefix is displayed as MSTP or MSTi, instead of PVRST.

Task ID


Task ID	Operation
l2vpn	read

Examples

The following example displays output for the show l2vpn database ac command:


RP/0/RP0/CPU0:router# show l2vpn database ac
				Bundle-Ether1.1:
				      Other-Segment MTU: 0
				      Other-Segment status flags: 0x0
				      Signaled capability valid: No
				      Signaled capability flags: 0x0
				      Configured capability flags: 0x0
				      XCID: 0xffffffff
				      PSN Type: Undefined
				      ETH data:
				          Xconnect tags: 0
				          Vlan rewrite tag: 0
				    AC defn:
				        ac-ifname: Bundle-Ether1.1
				        capabilities: 0x00368079
				        extra-capabilities: 0x00000000
				        parent-ifh: 0x020000e0
				        ac-type: 0x15
				        interworking: 0x00
				    AC info:
				        seg-status-flags: 0x00000000
				        segment mtu/l2-mtu: 1504/1518
				
				GigabitEthernet0/0/0/0.4096:
				      Other-Segment MTU: 0
				      Other-Segment status flags: 0x0
				      Signaled capability valid: No
				      Signaled capability flags: 0x0
				      Configured capability flags: 0x0
				      XCID: 0x0
				      PSN Type: Undefined
				      ETH data:
				          Xconnect tags: 0
				          Vlan rewrite tag: 0
				    AC defn:
				        ac-ifname: GigabitEthernet0_0_0_0.4096
				        capabilities: 0x00368079
				        extra-capabilities: 0x00000000
				        parent-ifh: 0x040000c0
				        ac-type: 0x15
				        interworking: 0x00
				    AC info:
				        seg-status-flags: 0x00000003
				        segment mtu/l2-mtu: 1504/1518

The following example displays output for the show l2vpn database node command:


RP/0/RP0/CPU0:router# show l2vpn database node
				0/RSP0/CPU0
				    MA: vlan_ma
				
				     AC event trace history [Total events: 4]
				     -----------------------------------------
				     Time                Event                          Num Rcvd        Num Sent
				     ====                =====                          ========        ========
				     07/27/2012 15:00:31 Process joined                 0               0
				     07/27/2012 15:00:31 Process init success           0               0
				     07/27/2012 15:00:31 Replay start rcvd              0               0
				     07/27/2012 15:00:31 Replay end rcvd                2               0
				
				
				    MA: ether_ma
				
				     AC event trace history [Total events: 4]
				     -----------------------------------------
				     Time                Event                          Num Rcvd        Num Sent
				     ====                =====                          ========        ========
				     07/27/2012 15:00:31 Process joined                 0               0
				     07/27/2012 15:00:31 Process init success           0               0
				     07/27/2012 15:00:31 Replay start rcvd              0               0
				     07/27/2012 15:00:31 Replay end rcvd                0               0
				
				
				
				0/0/CPU0
				    MA: vlan_ma
				
				     AC event trace history [Total events: 4]
				     -----------------------------------------
				     Time                Event                          Num Rcvd        Num Sent
				     ====                =====                          ========        ========
				     07/27/2012 15:00:31 Process joined                 0               0
				     07/27/2012 15:00:31 Process init success           0               0
				     07/27/2012 15:00:31 Replay start rcvd              0               0
				     07/27/2012 15:00:40 Replay end rcvd                6006            6001
				
				
				    MA: ether_ma
				
				     AC event trace history [Total events: 4]
				     -----------------------------------------
				     Time                Event                          Num Rcvd        Num Sent
				     ====                =====                          ========        ========
				     07/27/2012 15:00:31 Process joined                 0               0
				     07/27/2012 15:00:31 Process init success           0               0
				     07/27/2012 15:00:31 Replay start rcvd              0               0
				     07/27/2012 15:00:31 Replay end rcvd                1               0

show l2vpn forwarding

To display forwarding information from the layer2_fib manager on the line card, use the show l2vpn forwarding command in EXEC mode.

show l2vpn forwarding {xconnect | bridge-domain | counter | detail | hardware | inconsistent | interface | l2tp | location [node-id] | message | mstp | resource | retry-list | summary | unresolved}

Syntax Description


xconnect	Displays the cross-connect related information.
bridge-domain	Displays bridge domain related forwarding information.
counter	Displays the cross-connect counters.
detail	Displays detailed information from the layer2_fib manager.
hardware	Displays hardware-related layer2_fib manager information.
inconsistent	Displays inconsistent entries only.
interface	Displays the match AC subinterface.
l2tp	Displays L2TPv3 related forwarding information.
location `node-id`	Displays layer2_fib manager information for the specified location. The `node-id` argument is entered in the `rack/slot/module` notation.
message	Displays messages exchanged with collaborators.
mstp	Displays multi-spanning tree related forwarding information.
resource	Displays resource availability information in the layer2_fib manager.
retry-list	Displays retry list related information.
summary	Displays summary information about cross-connects in the layer2_fib manager.
unresolved	Displays unresolved entries only.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 3.4.0	This command was introduced.
Release 3.7.0	Sample output was updated to add MAC information for the layer2_fib manager summary.

Usage Guidelines

To use commands of this module, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using any command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read

Examples

The following sample output is from the show l2vpn forwarding bridge detail location command for IOS-XR releases 5.3.1 and earlier:


RP/0/RP0/CPU0:router# show l2vpn forwarding	bridge detail location 0/2/cpu0
Bridge-domain name: bg1:bd1, id: 0, state: up
 MAC learning: enabled
 Flooding:
   Broadcast & Multicast: enabled
   Unknown unicast: enabled
 MAC aging time: 300 s, Type: inactivity
 MAC limit: 4000, Action: none, Notification: syslog
 MAC limit reached: no
 Security: disabled
 DHCPv4 snooping: profile not known on this node
 IGMP snooping: disabled, flooding: disabled
 Bridge MTU: 1500 bytes
 Number of bridge ports: 1
 Number of MAC addresses: 0
 Multi-spanning tree instance: 0

  GigabitEthernet0/1/0/1.2, state: oper up
    Number of MAC: 0
    Statistics:
      packets: received 0, sent 0
      bytes: received 0, sent 0
    Storm control drop counters: 
      packets: broadcast 0, multicast 0, unknown unicast 0 
      bytes: broadcast 0, multicast 0, unknown unicast 0 


Bridge-domain name: bg1:bd2, id: 1, state: up
  Type:  pbb-edge, I-SID: 1234
  Core-bridge: pbb-bd2
 MAC learning: enabled
 Flooding:
   Broadcast & Multicast: enabled
   Unknown unicast: enabled
 MAC aging time: 300 s, Type: inactivity
 MAC limit: 4000, Action: none, Notification: syslog
 MAC limit reached: no
 Security: disabled
 DHCPv4 snooping: profile not known on this node
 IGMP snooping: disabled, flooding: disabled
 Bridge MTU: 1500 bytes
 Number of bridge ports: 0
 Number of MAC addresses: 0
 Multi-spanning tree instance: 0

 PBB Edge, state: up
    Number of MAC: 0
 GigabitEthernet0/1/0/1.3, state: oper up
    Number of MAC: 0
    Storm control drop counters: 
      packets: broadcast 0, multicast 0, unknown unicast 0 
      bytes: broadcast 0, multicast 0, unknown unicast 0 

Bridge-domain name: bg1:bd3, id: 2, state: up
  Type:  pbb-core 
  Number of associated pbb-edge BDs: 1

MAC learning: enabled
 Flooding:
   Broadcast & Multicast: enabled
   Unknown unicast: enabled
 MAC aging time: 300 s, Type: inactivity
 MAC limit: 4000, Action: none, Notification: syslog
 MAC limit reached: no
 Security: disabled
 DHCPv4 snooping: profile not known on this node
 IGMP snooping: disabled, flooding: disabled
 Bridge MTU: 1500 bytes
 Number of bridge ports: 0
 Number of MAC addresses: 0
 Multi-spanning tree instance: 0

  PBB Core, state: up
  Vlan-id: 1
 
  GigabitEthernet0/1/0/1.4, state: oper up
    Number of MAC: 0
    Storm control drop counters: 
      packets: broadcast 0, multicast 0, unknown unicast 0 
      bytes: broadcast 0, multicast 0, unknown unicast 0

The following sample output is from the show l2vpn forwarding bridge detail location command for IOS-XR 5.3.2 release:


RP/0/RP0/CPU0:router# show l2vpn forwarding	bridge detail location 0/0/CPU0

Bridge-domain name: pbb:pbb_core1, id: 10, state: up
 Type: pbb-core
 Number of associated pbb-edge BDs: 1
 MAC learning: enabled
 MAC port down flush: enabled
 Flooding:
   Broadcast & Multicast: enabled
   Unknown unicast: enabled
 MAC aging time: 300 s, Type: inactivity
 MAC limit: 4000, Action: none, Notification: syslog
 MAC limit reached: no
 MAC Secure: disabled, Logging: disabled
 DHCPv4 snooping: profile not known on this node
 Dynamic ARP Inspection: disabled, Logging: disabled
 IP Source Guard: disabled, Logging: disabled
 IGMP snooping: disabled, flooding: enabled
 MLD snooping: disabled, flooding: disabled
 MMRP Flood Optimization: disabled
 Storm control: disabled
 P2MP PW: disabled
 Bridge MTU: 1500 bytes
 Number of bridge ports: 1
 Number of MAC addresses: 5
 Multi-spanning tree instance: 0
 PBB-EVPN: enabled
 Statistics:
   packets: received 0, sent 963770
   bytes: received 0, sent 263433178

  PBB Core, state: Up
    Vlan-id: 1
    XC ID: 0x80000010
    Number of MAC: 0
    Statistics:
      packets: received 0 (unicast 0), sent 0
      bytes: received 0 (unicast 0), sent 0
      MAC move: 0
    Storm control drop counters: 
      packets: broadcast 0, multicast 0, unknown unicast 0 
      bytes: broadcast 0, multicast 0, unknown unicast 0

The following sample outputs shows the backup pseudowire information:


RP/0/RP0/CPU0:router#show l2vpn forwarding detail location 0/2/CPU0
Local interface: GigabitEthernet0/2/0/0.1, Xconnect id: 0x3000001, Status: up
  Segment 1
    AC, GigabitEthernet0/2/0/0.1, Ethernet VLAN mode, status: Bound
    RG-ID 1, active
    Statistics:
      packets: received 0, sent 0
      bytes: received 0, sent 0
  Segment 2
    MPLS, Destination address: 101.101.101.101, pw-id: 1000, status: Bound
    Pseudowire label: 16000
    Statistics:
      packets: received 0, sent 0
      bytes: received 0, sent 0
  Backup PW
    MPLS, Destination address: 102.102.102.102, pw-id: 1000, status: Bound
    Pseudowire label: 16001
    Statistics:
      packets: received 0, sent 0
      bytes: received 0, sent 0


RP/0/RP0/CPU0:router#show l2vpn forwarding bridge-domain detail location 0/2/CPU0
Bridge-domain name: bg1:bd1, id: 0, state: up
….
  GigabitEthernet0/2/0/0.4, state: oper up
    RG-ID 1, active
    Number of MAC: 0
    …..

  Nbor 101.101.101.101 pw-id 5000
    Backup Nbor 101.101.101.101 pw-id 5000
    Number of MAC: 0
….


RP/0/RP0/CPU0:router#show l2vpn forwarding bridge-domain detail location 0/2/CPU0
Bridge-domain name: bg1:bd1, id: 0, state: up
….
GigabitEthernet0/2/0/0.4, state: oper up
XC ID: 0x1880002
Number of MAC: 0
Statistics:
packets: received 0 (multicast 0, broadcast 0, unknown unicast 0, unicast 0), sent 963770
bytes: received 0 (multicast 0, broadcast 0, unknown unicast 0, unicast 0), sent 263433178
MAC move: 0
Storm control drop counters:
packets: broadcast 0, multicast 0, unknown unicast 0
bytes: broadcast 0, multicast 0, unknown unicast 0
Dynamic arp inspection drop counters:
packets: 0, bytes: 0
IP source guard drop counters:
packets: 0, bytes: 0

  

….

The following sample outputs displays the SPAN segment information of the xconnect:


RP/0/RP0/CPU0:router# show l2vpn forwarding counter location 0/7/CPU0 
Legend: ST = State, DN = Down

Segment 1                             Segment 2           ST     Byte
                                                                                Switched
----------------------------- -----------------------    --      ---------
pw-span-test (Monitor-Session) mpls  172.16.0.1  UP       0


RP/0/RP0/CPU0:router #Show l2vpn forwarding monitor-session location 0/7/CPU0
Segment 1                            Segment 2                            State
------------------------------------ ------------------------------------ ------
pw-span-test(monitor-session)  mpls    172.16.0.1                      UP
pw-span-sess(monitor-session)  mpls    192.168.0.1                      UP


RP/0/RP0/CPU0:router #Show l2vpn forwarding monitor-session pw-span-test location 0/7/CPU0
Segment 1                                 Segment 2                            State
------------------------------------ ------------------------------------ ------
pw-span-test(Monitor-Session) mpls    172.16.0.1                      UP


Example 4:
RP/0/RP0/CPU0:router #show l2vpn forwarding detail location 0/7/CPU0
  Xconnect id: 0xc000001, Status: up
  Segment 1
    Monitor-Session, pw-span-test, status: Bound
  Segment 2
    MPLS, Destination address: 172.16.0.1, pw-id: 1, status: Bound
    Pseudowire label: 16001
    Statistics:
      packets: received 0, sent 11799730
      bytes: received 0, sent 707983800

Example 5:
show l2vpn forwarding private location 0/11/CPU0
  Xconnect ID 0xc000001
  Xconnect info:
   Base info: version=0xaabbcc13, flags=0x0, type=2, reserved=0
    xcon_bound=TRUE, switching_type=0, data_type=3

  AC info:
   Base info: version=0xaabbcc11, flags=0x0, type=3, reserved=0
    xcon_id=0xc000001, ifh= none, subifh= none, ac_id=0, ac_type=SPAN,
    ac_mtu=1500, iw_mode=none, adj_valid=FALSE, adj_addr none
    

  PW info:
   Base info: version=0xaabbcc12, flags=0x0, type=4, reserved=0
    pw_id=1, nh_valid=TRUE, sig_cap_flags=0x20, context=0x0,
     MPLS, pw_label=16001
    Statistics:
      packets: received 0, sent 11799730
      bytes: received 0, sent 707983800

   Object: NHOP
   Event Trace History [Total events: 5]
--------------------------------------------------------------------
     Time                Event                Flags
     ====                =====                =====
   

--------------------------------------------------------------------


  Nexthop info:
   Base info: version=0xaabbcc14, flags=0x10000, type=5, reserved=0
    nh_addr=172.16.0.1, plat_data_valid=TRUE, plat_data_len=128, child_count=1

   Object: XCON
   Event Trace History [Total events: 16]
--------------------------------------------------------------------
     Time                Event                Flags
     ====                =====                =====

 -------------------------------------------------------------------
RP/0/RP0/CPU0:router #show l2vpn forwarding summary location 0/7/CPU0
 Major version num:1, minor version num:0
Shared memory timestamp:0x31333944cf
Number of forwarding xconnect entries:2
  Up:2  Down:0
  AC-PW:1 (1 mpls)  AC-AC:0  AC-BP:0  AC-Unknown:0
  PW-BP:0  PW-Unknown:0 Monitor-Session-PW:1
Number of xconnects down due to:
  AIB:0  L2VPN:0  L3FIB:0
Number of p2p xconnects: 2
Number of bridge-port xconnects: 0
Number of nexthops:1
  MPLS:   Bound:1  Unbound:0  Pending Registration:0
Number of bridge-domains: 0
Number of static macs: 0
Number of locally learned macs: 0
Number of remotely learned macs: 0
Number of total macs: 0

The following sample output is from the show l2vpn forwarding command:


RP/0/RP0/CPU0:router# show l2vpn forwarding location 0/2/cpu0

ID   Segment 1         Segment 2   
-----------------------------------
1    Gi0/2/0/0 1       10.0.0.1   9)

The following sample output shows the MAC information in the layer2_fib manager summary:


RP/0/RP0/CPU0:router# show l2vpn forwarding summary location 0/3/CPU0

Major version num:1, minor version num:0
Shared memory timestamp:0x66ff58e894
Number of forwarding xconnect entries:2
  Up:1  Down:0
  AC-PW:0  AC-AC:0  AC-BP:1 PW-BP:1
Number of xconnects down due to:
  AIB:0  L2VPN:0  L3FIB:0
Number of nexthops:1
Number of static macs: 5
Number of locally learned macs: 5
Number of remotely learned macs: 0
Number of total macs: 10

This example shows the sample output of a configured flow label:

RP/0/RP0/CPU0:router# show l2vpn for 0/0/cPU0
Local interface: GigabitEthernet0/0/1/1, Xconnect id: 0x1000002, Status: up
  Segment 1
    AC, GigabitEthernet0/0/1/1, Ethernet port mode, status: Bound
    
  Segment 2
    MPLS, Destination address: 192.168.0.1, pw-id: 2, status: Bound, Active
    Pseudowire label: 16004    Control word disabled
    Backup PW
      MPLS, Destination address: 172.16.0.1, pw-id: 6, status: Bound
      Pseudowire label: 16000
    Flow label enabled
    
					Xconnect id: 0xff000014, Status: down
  Segment 1
    MPLS, Destination address: 172.16.0.1, pw-id: 1, status: Not bound
		Pseudowire label: UNKNOWN    Control word disabled
    Flow label enabled
    
  Segment 2
    Bridge id: 0, Split horizon group id: 0
    Storm control: disabled
    MAC learning: enabled
    MAC port down flush: enabled
    Flooding:
      Broadcast & Multicast: enabled
      Unknown unicast: enabled
    MAC aging time: 300 s, Type: inactivity
    MAC limit: 4000, Action: none, Notification: syslog
    MAC limit reached: no
    Security: disabled
    DHCPv4 snooping: profile not known on this node, disabled
    IGMP snooping profile: profile not known on this node 
    Router guard disabled

Related Commands

Command	Description
clear l2vpn forwarding counters	Clears L2VPN forwarding counters.

show l2vpn forwarding l2tp

To display L2VPN forwarding information, use the show l2vpn forwarding l2tp command in EXEC mode.

show l2vpn forwarding l2tp disposition {local session id session-ID | hardware | location node-id} location node-id

Syntax Description


disposition	Displays forwarding disposition information.
`session-ID`	Displays L2TPv3-related forwarding information for the specified local session ID. Range is 1-4294967295.
hardware	Displays L2TPv3-related forwarding information read from hardware.
location	Displays L2TPv3-related forwarding information for the specified location.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 3.9.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read

Examples

The following example shows sample output for the show l2vpn forwarding l2tp command:


RP/0/RP0/CPU0:router# show l2vpn forwarding l2tp disposition hardware location 0/3/1

ID   Segment 1         Segment 2   
-----------------------------------
1    Gi0/2/0/0 1       10.0.0.1   9)

Related Commands

Command	Description
clear l2vpn forwarding counters	Clears L2VPN forwarding counters.

show l2vpn forwarding message counters

To display L2VPN forwarding messages exchanged with L2FIB Collaborators, use the show l2vpn forwarding message counters command in EXEC mode.

show l2vpn forwarding message counters {hardware | location node-id}

Syntax Description


hardware	Displays message counter information from hardware.
location `node-id`	Displays message counter information for the specified location.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Even when xSTP (extended spanning tree protocol) operates in the PVRST mode, the output of the show or debug commands flag prefix is displayed as MSTP or MSTi, instead of PVRST.

Task ID


Task ID	Operation
l2vpn	read

Examples

The following examples shows the output from the show l2vpn forwarding message counters location command:

RP/0/RP0/CPU0:router# show l2vpn forwarding message counters location 0/1/CPU0
Messages exchanged with L2FIB Collaborators:
-----------------------------------------------------------------------------------
     Message                                            Count       Info1        Info2        Time               
     =======                                            =====       =====        =====        ====               
     l2vpn provision messages received:                  0          0x0          0x0          -                  
     l2vpn unprovision messages received:                0          0x0          0x0          -                  
     l2vpn bridge provision messages received:           2          0x1          0x0          Jan  8 14:49:19.283
     l2vpn bridge unprovision messages received:         0          0x0          0x0          -                  
     l2vpn bridge main port update messages received:    1          0x2000300    0x0          Jan  8 12:02:15.628
     l2vpn bridge main port update w/ action=MSTI_DELETE 0          0x0          0x0          -                  
     l2vpn bridge main port update ACK sent:             1          0x2000300    0x0          Jan  8 12:02:15.628
     l2vpn bridge port provision messages received:      1          0x2000002    0x0          Jan  8 12:02:15.629
     l2vpn bridge port unprovision messages received:    0          0x0          0x0          -                  
     l2vpn shg provision messages received:              0          0x0          0x0          -                  
     l2vpn shg unprovision messages received:            0          0x0          0x0          -                  
     l2vpn static mac provision messages received:       1          0x0          0x0          Jan  9 08:41:36.668
     l2vpn static mac unprovision messages received:     1          0x0          0x0          Jan  9 08:44:24.208
     l2vpn dynamic mac local learning messages received: 0          0x0          0x0          -                  
     l2vpn dynamic mac remote learning messages received 0          0x0          0x0          -                  
     l2vpn dynamic mac refresh messages received:        0          0x0          0x0          -                  
     l2vpn dynamic mac unprovision messages received:    0          0x0          0x0          -                  
     AIB update messages received:                       4          0x2000102    0x2000300    Jan  8 12:02:15.622
     AIB delete messages received:                       0          0x0          0x0          -                  
     FIB nhop registration messages sent:                0          0x0          0x0          -                  
     FIB nhop unregistration messages sent:              0          0x0          0x0          -                  
     FIB ecd ldi update messages received:               0          0x0          0x0          -                  
     FIB invalid NHOP prov messages received:            0          0x0          0x0          -                  
     Backbone-source-mac prov messages received:         0          0x0          0x0          -          
     Backbone-source-mac unprov messages received:       0          0x0          0x0          -

Related Commands

Command	Description
clear l2vpn forwarding message counters	Clears L2VPN forwarding message counters.

show l2vpn generic-interface-list

To display all the L2VPN virtual interfaces, use the show l2vpn generic-interface-list command in EXEC mode.

show l2vpn generic-interface-list {detail | name | private | summary}

Syntax Description


detail	Specifies the details of the interface.
name	Specifies the name of the interface.
private	Specifies the private details of the interface.
summary	Specifies the summary information of the interface.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 4.2.1	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read

Examples

This example shows the sample output of the show l2vpn generic-interface-list command:


RP/0/RP0/CPU0:router# show l2vpn generic-interface-list
generic-interface-list: l1 (ID: 2, interfaces: 2)  Number of items: 20
generic-interface-list: l2 (ID: 3, interfaces: 4)  Number of items: 15

This example shows the sample output of the show l2vpn generic-interface-list detail command:


RP/0/RP0/CPU0:router# show l2vpn generic-interface-list detail
generic-interface-list: l1 (ID: 2, interfaces: 2)
   GigabitEthernet0/1/0/0 - items pending 2
   GigabitEthernet0/1/0/1 - items pending 4
   Number of items: 27
    PW-Ether: 1-10, 12-21
    PW-IW: 1-7

generic-interface-list: l2 (ID: 3, interfaces: 4)
   GigabitEthernet0/1/0/0 - items pending 2
   GigabitEthernet0/1/0/1 - items pending 4
   GigabitEthernet0/1/0/2 - items pending 1
   GigabitEthernet0/1/0/3 - items pending 0
   Number of items: 20
    PW-Ether: 1-15
    PW-IW: 1-7

This example shows the sample output of the show l2vpn generic-interface-list name | detail command:


RP/0/RP0/CPU0:router# show l2vpn generic-interface-list name 11 detail
generic-interface-list: l1 (ID: 2, interfaces: 2)
   GigabitEthernet0/1/0/0 - items pending 2
   GigabitEthernet0/1/0/1 - items pending 4
   Number of items: 20
    PW-Ether 1-10, 12-21

show l2vpn index

To display statistics about the index manager, use the show l2vpn index command in EXEC mode.

show l2vpn index [location | private | standby]

Syntax Description


location	(Optional) Displays index manager statistics for the specified location.
private	(Optional) Detailed information about all indexes allocated for each pool.
standby	(Optional) Displays Standby node specific information.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 4.2.1	This command was introduced.
Release 4.3.0	The following keywords are introduced: location standby

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read

Examples

This example shows the sample output of the show l2vpn index command:


RP/0/RP0/CPU0:router# show l2vpn index
			Pool id: 0x4, App: RD 
   Pool size: 32767
   zombied IDs: 0
   allocated IDs: 0

   Pool id: 0x5, App: IFLIST 
   Pool size: 65535
   zombied IDs: 0
   allocated IDs: 2

   Pool id: 0xff000001, App: PW/PBB/Virtual AC 
   Pool size: 40960
   zombied IDs: 0
   allocated IDs: 1

   Pool id: 0xff000002, App: BD 
   Pool size: 4095
   zombied IDs: 0
   allocated IDs: 2

   Pool id: 0xff000003, App: MP2MP 
   Pool size: 65535
   zombied IDs: 0
   allocated IDs: 1

This example shows the sample output of the show l2vpn index standby command:


RP/0/RP0/CPU0:router# show l2vpn index standby
			 Pool id: 0xfffc0000, App: Global
			   Max number of ID mgr instances: 1
			   ID mgr instances in use: 1
			   Pool size: 98304
			   zombied IDs: 0
			   allocated IDs: 0
			
			 Pool id: 0xfffc0002, App: BD
			   Max number of ID mgr instances: 1
			   ID mgr instances in use: 1
			   Pool size: 8192
			   zombied IDs: 0
			   allocated IDs: 0
			
			 Pool id: 0xfffc0003, App: MP2MP
			   Max number of ID mgr instances: 1
			   ID mgr instances in use: 1
			   Pool size: 65535
			   zombied IDs: 0
			   allocated IDs: 0

show l2vpn nsr

To display the status of l2vpn non-stop routing, use the show l2vpn nsr command in EXEC mode.

show l2vpn nsr [location | standby]

Syntax Description


location	(Optional) Displays non-stop routing information for the specified location.
standby	(Optional) Displays Standby node specific information.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 4.3.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operation
l2vpn	read

Examples

The following example displays output for the show l2vpn nsr command:


RP/0/RP0/CPU0:router# show l2vpn nsr
				
Mon May 30 19:32:01.045 UTC
L2VPN NSR information
  NSR Status:
    NSR Ready               : Fri May 27 10:50:59 UTC 2016 (3d08h ago)
    Last NSR Withdraw Time  : Fri May 27 10:50:59 UTC 2016 (3d08h ago)
    Standby Connected       : Fri May 27 10:50:59 UTC 2016 (3d08h ago)
    IDT Done                : Fri May 27 10:50:59 UTC 2016 (3d08h ago)
    Number of XIDs sent     : Virtual AC: 0
                              AC        : 1
                              PW        : 1
                              BD        : 0
                              MP2MP     : 0
                              RD        : 0
                              PBB       : 0
                              IFLIST    : 0
                              ATOM      : 1
                              Global    : 0
                              PWGroup   : 0
                              EVPN      : 0

Related Commands

Command	Description
l2vpn	Enters L2VPN configuration mode.

show l2vpn process fsm

To display the status of the l2vpn process finite state machine, use the show l2vpn process fsm command in EXEC mode. It displays the current process role and state, NSR status, ISSU status, role change status, and status of collaborators.

show l2vpn process fsm [location | standby]

Syntax Description


location	(Optional) Displays non-stop routing information for the specified location.
standby	(Optional) Displays Standby node specific information.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 6.1.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operation
l2vpn	read

Examples

The following example displays output for the show l2vpn process fsm command:


RP/0/RP0/CPU0:router# show l2vpn process fsm
				
Mon May 16 10:20:30.967 PDT
L2VPN Process FSM
  Current process role      : Primary Active (Master)
  Current process state     : Run
  S/w install in progress   : No
  NSR Status:
    NSR Ready               : No
    Last NSR Withdraw Time  : Mon May 16 10:19:58 PDT 2016 (00:00:33 ago)
    Standby Connected       : No
    IDT Done                : Never
    Number of XIDs sent     : Virtual AC: 0
                              AC        : 1
                              PW        : 1
                              BD        : 0
                              MP2MP     : 0
                              RD        : 0
                              PBB       : 0
                              IFLIST    : 0
                              ATOM      : 1
                              Global    : 0
                              PWGroup   : 0
                              EVPN      : 0
  Process Role Change Status:
    Role Change Triggered   : No Role Change
    Role Change Start       : No
    Role Change End         : No
  Process State Transition Time:
    Process-Start           : Mon May 16 10:19:29 PDT 2016 (00:01:02 ago)
    Process-Init            : Mon May 16 10:19:30 PDT 2016 (00:01:01 ago)
    Role-based Init         : Mon May 16 10:19:31 PDT 2016 (00:01:00 ago)
    Wait-Collab-Conn        : Mon May 16 10:19:31 PDT 2016 (00:01:00 ago)
    Run                     : Mon May 16 10:19:58 PDT 2016 (00:00:33 ago)
  Process Collaborator Report Card:
    Collaborator        Connection Status (Since)                               IDT Done (At)
  ===========================================================================================================================
    NSR-INFRA           Up   (Mon May 16 10:19:30 PDT 2016 (00:01:01 ago))      N/A
    NSR-PEER            Down (Never came Up)                                    No
    ISSU-PEER           Down (Never came Up)                                    No
    SYSDB-CONFIG        Up   (Mon May 16 10:19:30 PDT 2016 (00:01:01 ago))      Mon May 16 10:19:58 PDT 2016 (00:00:33 ago)

Related Commands

Command	Description
l2vpn	Enters L2VPN configuration mode.

show l2vpn index	Displays statistics about the index manager.

show l2vpn provision queue

To display L2VPN configuration provisioning queue information, use the show l2vpn provision queue command in EXEC mode.

show l2vpn provision queue [location | standby]

Syntax Description


location	(Optional) Displays L2VPN configuration provisioning queue information for the specified location.
standby	(Optional) Displays Standby node specific information.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 4.3.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operation
l2vpn	read

Examples

The following example displays output for the show l2vpn provision queue command:


RP/0/RP0/CPU0:router# show l2vpn provision queue
				
				Legend: P/P/R = Priority/Provisioned/Require Provisioning.
				Configuration Item         Object Type              Class                  P/P/R Object Key
				-------------------------- ------------------------ ---------------------- ----- ----------
				BD_NAME                    bd_t                     vpls_bd_class          0/0/0 BD VPLS01
				BD_NAME                    bd_t                     vpls_bd_class          0/0/0 BD VPLS02
				BD_NAME                    bd_t                     vpls_bd_class          0/0/0 BD VPLS03

The following example displays output for the show l2vpn provision queue standby command:


RP/0/RP0/CPU0:router# show l2vpn provision queue standby
				Legend: P/P/R = Priority/Provisioned/Require Provisioning.
				Configuration Item         Object Type              Class                  P/P/R Object Key
				-------------------------- ------------------------ ---------------------- ----- ----------
				BD_NAME                    bd_t                     vpls_bd_class          0/0/0 BD VPLS01
				BD_NAME                    bd_t                     vpls_bd_class          0/0/0 BD VPLS02
				BD_NAME                    bd_t                     vpls_bd_class          0/0/0 BD VPLS03
				BD_NAME                    bd_t                     vpls_bd_class          0/0/0 BD VPLS04
				BD_NAME                    bd_t                     vpls_bd_class          0/0/0 BD VPLS05
				BD_NAME                    bd_t                     vpls_bd_class          0/0/0 BD VPLS06
				BD_NAME                    bd_t                     vpls_bd_class          0/0/0 BD VPLS07
				BD_NAME                    bd_t                     vpls_bd_class          0/0/0 BD VPLS08
				BD_NAME                    bd_t                     vpls_bd_class          0/0/0 BD VPLS09
				BD_NAME                    bd_t                     vpls_bd_class          0/0/0 BD VPLS010

Related Commands

Command	Description
l2vpn	Enters L2VPN configuration mode.

show l2vpn pw-class

To display L2VPN pseudowire class information, use the show l2vpn pw-class command in EXEC mode.

show l2vpn pw-class [detail | location | name class name | standby]

Syntax Description


detail	(Optional) Displays detailed information.
location	(Optional) Displays location specific information.
name `class-name`	(Optional) Displays information about a specific pseudowire class name.
standby	(Optional) Displays standby node specific information.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 3.5.0	This command was introduced.
Release 4.3.0	The keywords location and standby were introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read

Examples

The following example shows sample output for the show l2vpn pw-class command:


RP/0/RP0/CPU0:router# show l2vpn pw-class

Name                        Encapsulation     Protocol       
-------------------------   ----------        ----------     
mplsclass_75                MPLS              LDP 
l2tp-dynamic                L2TPv3            L2TPv3

This example shows sample output for the show l2vpn pw-class detail command:


RP/0/RP0/CPU0:router# show l2vpn pw-class detail
				Encapsulation MPLS, protocol LDP
    Transport mode not set, control word unset (default)
    Sequencing not set
    Static tag rewrite not set
    PW Backup disable delay: 0 sec 
    MAC withdraw message is sent over PW: no
    IPv4 source address 10.0.0.1

This table describes the significant fields shown in the display.

Table 6. show l2vpn pw-class Command Field Descriptions
Field	Description
Name	Displays the name of the pseudowire class.
Encapsulation	Displays the encapsulation type.
Protocol	Displays the protocol type.

Related Commands

Command	Description
clear l2vpn forwarding counters	Clears L2VPN forwarding counters.

show l2vpn pwhe

To display the pseudowire headend (PWHE) information, use the show l2vpn pwhe command in EXEC mode.

show l2vpn pwhe {detail | interface | summary}

Syntax Description


detail	Specifies the details of the interface.
interface	Specifies the name of the interface.
summary	Specifies the summary information of the interface.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 4.2.1	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read

Examples

This example show the sample output for show l2vpn pwhe detail command:


RP/0/RP0/CPU0:router# show l2vpn pwhe detail
Interface: PW-Ether1   Interface State: Down, Admin state: Up
  Interface handle 0x20000070
  MTU:  1514
  BW:   10000 Kbit
  Interface MAC addresses: 0279.96e9.8205
  Label: 16000
  L2-overhead: 0
  VC-type: 5
  CW: N
  Generic-interface-list: ifl1 (id: 1)
   Gi0/2/0/1, in bundle BE3, state: Up, replication: success
   Gi0/2/0/0, in bundle BE5, state: Up, replication: success
   Gi0/2/0/2, in bundle BE5, state: Up, replication: success
   Gi0/2/0/3, state: Up, replication: success

Interface: PW-IW1   Interface State: Up, Admin state: Up
  Interface handle 0x20000070
  MTU:  1514
  BW:   10000 Kbit
  VC-type: 11
  CW: N
  Generic-interface-list: ifl2 (id: 2)
   Gi0/3/0/1, in bundle BE6, state: Up, replication: success
   Gi0/3/0/0, in bundle BE6, state: Up, replication: success
   Gi0/3/0/2, state: Up, replication: success
   Gi0/3/0/3, state: Up, replication: success

This example show the sample output for show l2vpn pwhe summary command:


RP/0/RP0/CPU0:router# show l2vpn pwhe summary
		Number of PW-HE interface: 1600
  Up: 1300 Down: 300 Admindown: 0
  Number of PW-Ether interfaces: 900
  Up: 700  Down: 200  Admindown: 0
  Number of PW-IW interfaces: 700
  Up: 600  Down: 100  Admindown: 0

show l2vpn resource

To display the memory state in the L2VPN process, use the show l2vpn resource command in EXEC mode.

show l2vpn resource

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 3.4.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read

Examples

The following example shows sample output for the show l2vpn resource command:


RP/0/RP0/CPU0:router# show l2vpn resource

Memory: Normal

describes the significant fields shown in the display.Table 1

Table 7. show l2vpn resource Command Field Descriptions
Field	Description
Memory	Displays memory status.

show l2vpn trace

To display trace data for L2VPN, use the show l2vpn trace command in EXEC mode.

Syntax Description


checker	Displays trace data for the L2VPN Uberverifier.
file	Displays trace data for the specified file.
hexdump	Display traces data in hexadecimal format.
last	Display last <n> entries
location	Displays trace data for the specified location.
reverse	Display latest traces first
stats	Display trace statistics
tailf	Display new traces as they are added
unique	Display unique entries with counts
usec	Display usec details with timestamp
verbose	Display internal debugging information
wide	Display trace data excluding buffer name, node name, tid
wrapping	Display wrapping entries

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 4.3.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operation
l2vpn	read

Examples

This example displays output for the show l2vpn trace command:


RP/0/RP0/CPU0:router# show l2vpn trace
				310 unique entries (1775 possible, 0 filtered)
				Jul 27 14:39:51.786 l2vpn/fwd-detail 0/RSP0/CPU0 2# t1  FWD_DETAIL:415: l2tp session table rebuilt
				Jul 27 14:39:52.106 l2vpn/issu 0/RSP0/CPU0 1# t1  ISSU:788: ISSU - iMDR init called; 'infra/imdr' detected the 'informational' condition 'the service is not supported in the node'
				Jul 27 14:39:52.107 l2vpn/issu 0/RSP0/CPU0 1# t1  ISSU:428: ISSU - attempt to start COLLABORATOR wait timer while not in ISSU mode
				Jul 27 14:39:54.286 l2vpn/fwd-common 0/RSP0/CPU0 1# t1  FWD_COMMON:3257: show edm thread initialized
				Jul 27 14:39:55.270 l2vpn/fwd-mac 0/RSP0/CPU0 1# t1  FWD_MAC|ERR:783: Mac aging init
				Jul 27 14:39:55.286 l2vpn/fwd-mac 0/RSP0/CPU0 1# t1  FWD_MAC:1765: l2vpn_gsp_cons_init returned No error
				Jul 27 14:39:55.340 l2vpn/fwd-mac 0/RSP0/CPU0 1# t1  FWD_MAC:1792: Client successfully joined gsp group
				Jul 27 14:39:55.340 l2vpn/fwd-mac 0/RSP0/CPU0 1# t1  FWD_MAC:779: Initializing the txlist IPC thread
				Jul 27 14:39:55.341 l2vpn/fwd-mac 0/RSP0/CPU0 1# t1  FWD_MAC:2971: gsp_optimal_msg_size = 4832 (real: True)
				Jul 27 14:39:55.351 l2vpn/fwd-mac 0/RSP0/CPU0 1# t1  FWD_MAC:626: Entering mac aging timer init

show l2vpn xconnect

To display brief information on configured cross-connects, use the show l2vpn xconnect command in EXEC mode.

Syntax Description


brief	(Optional) Displays encapsulation brief information.
detail	(Optional) Displays detailed information.
`encapsulation`	(Optional) Filters on encapsulation type.
group	(Optional) Displays all cross-connects in a specified group.
groups	(Optional) Displays all groups information.
interface	(Optional) Filters the interface and subinterface.
location	(Optional) Displays location specific information.
mp2mp	(Optional) Displays MP2MP information.
mspw	(Optional) Displays ms_pw information.
neighbor	(Optional) Filters the neighbor.
pw-class	(Optional) Filters on pseudowire class
standby	(Optional) Displays standby node specific information.
state	(Optional) Filters the following xconnect state types: up down
summary	(Optional) Displays AC information from the AC Manager database.
type	(Optional) Filters the following xconnect types: ac-pw locally switched
state unresolved	(Optional) Displays information about unresolved cross-connects.
pw-id `value`	Displays the filter for the pseudowire ID. The range is from 1 to 4294967295.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 3.4.0	This command was introduced.
Release 3.4.1	VCCV-related show command output was added.
Release 3.6.0	Preferred-path-related show command output was added.
Release 3.7.0	Sample output was updated to display the backup pseudowire information.
Release 4.3.0	The following keywords were introduced: brief encapsulation groups location mp2mp mspw pw-class standby
Release 5.1.2	This command was modified to enable filtering the command output for a specific pseudowire with just the pseudowire ID.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

If a specific cross-connect is specified in the command (for instance, AC_to_PW1) then only that cross-connect will be displayed; otherwise, all cross-connects are displayed.

When configuring Ethernet Connectivity Fault Managment (CFM) over l2vpn cross-connect, the CFM Continuity Check Messages (CCM) packets are not accounted for in the cross-connect pseudowire packet counters displayed in this show command output.

Note

For Cisco IOS XR software Release 5.1.2 and above, you can filter the command output for specific pseudowire with just the pseudowire ID. However, for pseudowire configurations with FEC 129 Type 2 (in VPWS), filtering the output for a specific pseudowire can only be done with the combination of the neighbour filter and the pseudowire ID.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows sample output for the show l2vpn xconnect command:


RP/0/RP0/CPU0:router# show l2vpn xconnect
Wed May 21 09:06:47.944 UTC
Legend: ST = State, UP = Up, DN = Down, AD = Admin Down, UR = Unresolved,
        SB = Standby, SR = Standby Ready, (PP) = Partially Programmed

XConnect                   Segment 1                       Segment 2                
Group      Name       ST   Description            ST       Description            ST    
------------------------   -----------------------------   ---------------------------
L2TPV3_V4_XC_GRP
           L2TPV3_P2P_1
                      UP   Gi0/2/0/1.2            UP       26.26.26.26     100    UP    
--------------------------------------------------------------------------------------
L2TPV3_V4_XC_GRP
           L2TPV3_P2P_2
                      UP   Gi0/2/0/1.3            UP       26.26.26.26     200    UP    
--------------------------------------------------------------------------------------

The following sample output shows that the backup is in standby mode for the show l2vpn xconnect detail  command:

RP/0/RP0/CPU0:router# show l2vpn xconnect detail

Group siva_xc, XC siva_p2p, state is up; Interworking none
  Monitor-Session: pw-span-test, state is configured
  AC: GigabitEthernet0/4/0/1, state is up
    Type Ethernet
    MTU 1500; XC ID 0x5000001; interworking none; MSTi 0
    Statistics:
      packet totals: send 90
      byte totals: send 19056
  PW: neighbor 10.1.1.1, PW ID 1, state is up ( established )
    PW class not set, XC ID 0x5000001
    Encapsulation MPLS, protocol LDP
    PW type Ethernet, control word enabled, interworking none
    PW backup disable delay 0 sec
    Sequencing not set
        MPLS         Local                          Remote                        
      ------------ ------------------------------ -----------------------------
      Label        30005                          16003                         
      Group ID     0x5000300                      0x5000400                     
      Interface    GigabitEthernet0/4/0/1         GigabitEthernet0/4/0/2 
       Interface   pw-span-test                 GigabitEthernet0/3/0/1 
      MTU          1500                           1500                          
      Control word enabled                        enabled                       
      PW type      Ethernet                       Ethernet                      
      VCCV CV type 0x2                            0x2                           
                   (LSP ping verification)        (LSP ping verification)       
      VCCV CC type 0x3                            0x3                           
                    (control word)                 (control word)                
                   (router alert label)           (router alert label)          
      ------------ ------------------------------ -----------------------------
    Create time: 20/11/2007 21:45:07 (00:49:18 ago)
    Last time status changed: 20/11/2007 21:45:11 (00:49:14 ago)
    Statistics:
      packet totals: receive 0
      byte totals: receive 0

  Backup PW:
  PW: neighbor 172.16.0.1, PW ID 2, state is up ( established )
    Backup for neighbor 10.0.0.1 PW ID 1 ( standby )
    PW class not set, XC ID 0x0
    Encapsulation MPLS, protocol LDP
    PW type Ethernet, control word enabled, interworking none
    PW backup disable delay 0 sec
    Sequencing not set
        MPLS         Local                          Remote                        
      ------------ ------------------------------ -----------------------------
      Label        30006                          16003                         
      Group ID     unassigned                     0x5000400                     
      Interface    unknown                        GigabitEthernet0/4/0/2        
      MTU          1500                           1500                          
      Control word enabled                        enabled                       
      PW type      Ethernet                       Ethernet                      
      VCCV CV type 0x2                            0x2                           
                   (LSP ping verification)        (LSP ping verification)       
      VCCV CC type 0x3                            0x3                           
                    (control word)                 (control word)                
                   (router alert label)           (router alert label)          
      ------------ ------------------------------ -----------------------------
    Backup PW for neighbor 10.1.1.1 PW ID 1
    Create time: 20/11/2007 21:45:45 (00:48:40 ago)
    Last time status changed: 20/11/2007 21:45:49 (00:48:36 ago)
    Statistics:
      packet totals: receive 0
      byte totals: receive 0

The following sample output shows that the backup is active for the show l2vpn xconnect detail  command:

RP/0/RP0/CPU0:router# show l2vpn xconnect detail

Group siva_xc, XC siva_p2p, state is down; Interworking none
  Monitor-Session: pw-span-test, state is configured
  AC: GigabitEthernet0/4/0/1, state is up
    Type Ethernet
    MTU 1500; XC ID 0x5000001; interworking none; MSTi 0
    Statistics:
      packet totals: send 98
      byte totals: send 20798
  PW: neighbor 10.1.1.1, PW ID 1, state is down ( local ready )
    PW class not set, XC ID 0x5000001
    Encapsulation MPLS, protocol LDP
    PW type Ethernet, control word enabled, interworking none
    PW backup disable delay 0 sec
    Sequencing not set
        MPLS         Local                          Remote                        
      ------------ ------------------------------ -----------------------------
      Label        30005                          unknown                       
      Group ID     0x5000300                      0x0                           
      Interface    GigabitEthernet0/4/0/1         unknown   
       Interface     pw-span-test                      GigabitEthernet0/3/0/1
      MTU          1500                           unknown                       
      Control word enabled                        unknown                       
      PW type      Ethernet                       unknown                       
      VCCV CV type 0x2                            0x0                           
                                                  (none)                        
                   (LSP ping verification)                                      
      VCCV CC type 0x3                            0x0                           
                                                  (none)                        
                    (control word)                                               
                   (router alert label)                                         
      ------------ ------------------------------ -----------------------------
    Create time: 20/11/2007 21:45:06 (00:53:31 ago)
    Last time status changed: 20/11/2007 22:38:14 (00:00:23 ago)
    Statistics:
      packet totals: receive 0
      byte totals: receive 0

  Backup PW:
  PW: neighbor 10.2.2.2, PW ID 2, state is up ( established )
    Backup for neighbor 10.1.1.1 PW ID 1 ( active )
    PW class not set, XC ID 0x0
    Encapsulation MPLS, protocol LDP
    PW type Ethernet, control word enabled, interworking none
    PW backup disable delay 0 sec
    Sequencing not set
        MPLS         Local                          Remote                        
      ------------ ------------------------------ -----------------------------
      Label        30006                          16003                         
      Group ID     unassigned                     0x5000400                     
      Interface    unknown                        GigabitEthernet0/4/0/2        
      MTU          1500                           1500                          
      Control word enabled                        enabled                       
      PW type      Ethernet                       Ethernet                      
      VCCV CV type 0x2                            0x2                           
                   (LSP ping verification)        (LSP ping verification)       
      VCCV CC type 0x3                            0x3                           
                    (control word)                 (control word)                
                   (router alert label)           (router alert label)          
      ------------ ------------------------------ -----------------------------
    Backup PW for neighbor 10.1.1.1 PW ID 1
    Create time: 20/11/2007 21:45:44 (00:52:54 ago)
    Last time status changed: 20/11/2007 21:45:48 (00:52:49 ago)
    Statistics:
      packet totals: receive 0
      byte totals: receive 0

The following sample output displays the xconnects with switch port analyzer (SPAN) as one of the segments:


Show l2vpn xconnect type minotor-session-pw
Legend: ST = State, UP = Up, DN = Down, AD = Admin Down, UR = Unresolved,
        LU = Local Up, RU = Remote Up, CO = Connected

XConnect                         Segment 1                    Segment 2                
Group             Name       ST     Description           ST   Description            ST
-----------------------------   ---------------------------  --------------------------
g1                x1        UP    pw-span-test          UP   172.16.0.1         1      UP
--------------------------------------------------------------------------------------

The following sample output shows that one-way redundancy is enabled:


Group g1, XC x2, state is up; Interworking none
  AC: GigabitEthernet0/2/0/0.2, state is up, active in RG-ID 1
    Type VLAN; Num Ranges: 1
    VLAN ranges: [2, 2]
    MTU 1500; XC ID 0x3000002; interworking none
    Statistics:
      packets: received 103, sent 103
      bytes: received 7348, sent 7348
      drops: illegal VLAN 0, illegal length 0
  PW: neighbor 101.101.101.101, PW ID 2000, state is up ( established )
    PW class class1, XC ID 0x3000002
    Encapsulation MPLS, protocol LDP
    PW type Ethernet VLAN, control word disabled, interworking none
PW backup disable delay 0 sec
One-way PW redundancy mode is enabled
    Sequencing not set
…..
    Incoming Status (PW Status TLV):
      Status code: 0x0 (Up) in Notification message
    Outgoing Status (PW Status TLV):
      Status code: 0x0 (Up) in Notification message
…..
  Backup PW:
  PW: neighbor 102.102.102.102, PW ID 3000, state is standby ( all ready )
    Backup for neighbor 101.101.101.101 PW ID 2000 ( inactive )
    PW class class1, XC ID 0x3000002
    Encapsulation MPLS, protocol LDP
    PW type Ethernet VLAN, control word disabled, interworking none
    Sequencing not set
…..
    Incoming Status (PW Status TLV):
      Status code: 0x26 (Standby, AC Down) in Notification message
    Outgoing Status (PW Status TLV):
      Status code: 0x0 (Up) in Notification message

The following example shows sample output for the show l2vpn xconnect command:


RP/0/RP0/CPU0:router# show l2vpn xconnect

Legend: ST = State, UP = Up, DN = Down, AD = Admin Down, UR = Unresolved,
              LU = Local Up, RU = Remote Up, CO = Connected

XConnect                   Segment 1                   Segment 2                
Group      Name       ST   Description            ST   Description            ST
----------------------------   ---------------------------   -------------------------
siva_xc    siva_p2p   UP   Gi0/4/0/1              UP   10.0.0.1         1      UP
                                                       Backup                   
                                                       172.16.0.1       2      UP
--------------------------------------------------------------------------------

The following sample output shows that the backup is in standby mode for the show l2vpn xconnect detail  command:

RP/0/RP0/CPU0:router# show l2vpn xconnect detail

Group siva_xc, XC siva_p2p, state is up; Interworking none
  AC: GigabitEthernet0/4/0/1, state is up
    Type Ethernet
    MTU 1500; XC ID 0x5000001; interworking none; MSTi 0
    Statistics:
      packet totals: received 90, sent 90
      byte totals: received 19056, sent 19056
  PW: neighbor 10.0.0.1, PW ID 1, state is up ( established )
    PW class not set, XC ID 0x5000001
    Encapsulation MPLS, protocol LDP
    PW type Ethernet, control word enabled, interworking none
    PW backup disable delay 0 sec
    Sequencing not set
        MPLS         Local                          Remote                        
      ------------ ------------------------------ -----------------------------
      Label        30005                          16003                         
      Group ID     0x5000300                      0x5000400                     
      Interface    GigabitEthernet0/4/0/1         GigabitEthernet0/4/0/2        
      MTU          1500                           1500                          
      Control word enabled                        enabled                       
      PW type      Ethernet                       Ethernet                      
      VCCV CV type 0x2                            0x2                           
                   (LSP ping verification)        (LSP ping verification)       
      VCCV CC type 0x3                            0x3                           
                    (control word)                 (control word)                
                   (router alert label)           (router alert label)          
      ------------ ------------------------------ -----------------------------
    Create time: 20/11/2007 21:45:07 (00:49:18 ago)
    Last time status changed: 20/11/2007 21:45:11 (00:49:14 ago)
    Statistics:
      packet totals: received 0, sent 0
      byte totals: received 0, sent 0

  Backup PW:
  PW: neighbor 172.16.0.1, PW ID 2, state is up ( established )
    Backup for neighbor 10.0.0.1 PW ID 1 ( standby )
    PW class not set, XC ID 0x0
    Encapsulation MPLS, protocol LDP
    PW type Ethernet, control word enabled, interworking none
    PW backup disable delay 0 sec
    Sequencing not set
        MPLS         Local                          Remote                        
      ------------ ------------------------------ -----------------------------
      Label        30006                          16003                         
      Group ID     unassigned                     0x5000400                     
      Interface    unknown                        GigabitEthernet0/4/0/2        
      MTU          1500                           1500                          
      Control word enabled                        enabled                       
      PW type      Ethernet                       Ethernet                      
      VCCV CV type 0x2                            0x2                           
                   (LSP ping verification)        (LSP ping verification)       
      VCCV CC type 0x3                            0x3                           
                    (control word)                 (control word)                
                   (router alert label)           (router alert label)          
      ------------ ------------------------------ -----------------------------
    Backup PW for neighbor 10.0.0.1 PW ID 1
    Create time: 20/11/2007 21:45:45 (00:48:40 ago)
    Last time status changed: 20/11/2007 21:45:49 (00:48:36 ago)
    Statistics:
      packet totals: received 0, sent 0
      byte totals: received 0, sent 0

The following sample output shows that the backup is active for the show l2vpn xconnect detail  command:

RP/0/RP0/CPU0:router# show l2vpn xconnect detail

Group siva_xc, XC siva_p2p, state is down; Interworking none
  AC: GigabitEthernet0/4/0/1, state is up
    Type Ethernet
    MTU 1500; XC ID 0x5000001; interworking none; MSTi 0
    Statistics:
      packet totals: send 98
      byte totals: send 20798
  PW: neighbor 10.0.0.1, PW ID 1, state is down ( local ready )
    PW class not set, XC ID 0x5000001
    Encapsulation MPLS, protocol LDP
    PW type Ethernet, control word enabled, interworking none
    PW backup disable delay 0 sec
    Sequencing not set
        MPLS         Local                          Remote                        
      ------------ ------------------------------ -----------------------------
      Label        30005                          unknown                       
      Group ID     0x5000300                      0x0                           
      Interface    GigabitEthernet0/4/0/1         unknown                       
      MTU          1500                           unknown                       
      Control word enabled                        unknown                       
      PW type      Ethernet                       unknown                       
      VCCV CV type 0x2                            0x0                           
                                                  (none)                        
                   (LSP ping verification)                                      
      VCCV CC type 0x3                            0x0                           
                                                  (none)                        
                    (control word)                                               
                   (router alert label)                                         
      ------------ ------------------------------ -----------------------------
    Create time: 20/11/2007 21:45:06 (00:53:31 ago)
    Last time status changed: 20/11/2007 22:38:14 (00:00:23 ago)
    Statistics:
      packet totals: received 0, sent 0
      byte totals: received 0, sent 0

  Backup PW:
  PW: neighbor 172.16.0.1, PW ID 2, state is up ( established )
    Backup for neighbor 10.0.0.1 PW ID 1 ( active )
    PW class not set, XC ID 0x0
    Encapsulation MPLS, protocol LDP
    PW type Ethernet, control word enabled, interworking none
    PW backup disable delay 0 sec
    Sequencing not set
        MPLS         Local                          Remote                        
      ------------ ------------------------------ -----------------------------
      Label        30006                          16003                         
      Group ID     unassigned                     0x5000400                     
      Interface    unknown                        GigabitEthernet0/4/0/2        
      MTU          1500                           1500                          
      Control word enabled                        enabled                       
      PW type      Ethernet                       Ethernet                      
      VCCV CV type 0x2                            0x2                           
                   (LSP ping verification)        (LSP ping verification)       
      VCCV CC type 0x3                            0x3                           
                    (control word)                 (control word)                
                   (router alert label)           (router alert label)          
      ------------ ------------------------------ -----------------------------
    Backup PW for neighbor 10.0.0.1 PW ID 1
    Create time: 20/11/2007 21:45:44 (00:52:54 ago)
    Last time status changed: 20/11/2007 21:45:48 (00:52:49 ago)
    Statistics:
      packet totals: received 0, sent 0
      byte totals: received 0, sent 0

This example shows that the PW type changes to Ethernet, which is Virtual Circuit (VC) type 5, on the interface when a double tag rewrite option is used.

RP/0/RP0/CPU0:router# show l2vpn xconnect pw-class pw-class1 detail

Group VPWS, XC ac3, state is up; Interworking none
AC: GigabitEthernet0/7/0/5.3, state is up
Type VLAN; Num Ranges: 1
VLAN ranges: [12, 12]
MTU 1508; XC ID 0x2440096; interworking none
Statistics:
packets: received 26392092, sent 1336
bytes: received 1583525520, sent 297928
drops: illegal VLAN 0, illegal length 0
PW: neighbor 192.168.0.1, PW ID 3, state is up ( established )
PW class VPWS1, XC ID 0x2440096
Encapsulation MPLS, protocol LDP
PW type Ethernet, control word disabled, interworking none
PW backup disable delay 0 sec
Sequencing not set

Preferred path tunnel TE 3, fallback disabled
PW Status TLV in use
						MPLS         Local                          Remote
						------------ ------------------------------ -----------------------------
						Label        16147                          21355
						Group ID     0x120001c0                     0x120001c0
      Interface    GigabitEthernet0/7/0/5.3       GigabitEthernet0/7/0/5.3
      MTU          1508                           1508
      Control word disabled                       disabled
      PW type      Ethernet                       Ethernet                    
      VCCV CV type 0x2                            0x2
                   (LSP ping verification)        (LSP ping verification)
      VCCV CC type 0x6                            0x6
                   (router alert label)           (router alert label)
                   (TTL expiry)                   (TTL expiry)
      ------------ ------------------------------ -----------------------------
Incoming Status (PW Status TLV):
Status code: 0x0 (Up) in Notification message
Outgoing Status (PW Status TLV):
Status code: 0x0 (Up) in Notification message
MIB cpwVcIndex: 4294705365
Create time: 21/09/2011 08:05:01 (00:14:01 ago)
Last time status changed: 21/09/2011 08:07:01 (00:12:01 ago)
Statistics:
packets: received 1336, sent 26392092
bytes: received 297928, sent 1583525520

This example shows the sample output of a pseudowire headend (PWHE) cross connect:


RP/0/RP0/CPU0:router#  show l2vpn xconnect interface pw-ether 67 detail
Group g1, XC xc1, state is down; Interworking none
  AC:PW-Ether1, state is up
    Type PW-Ether 
    Interface-list: interfacelist1
    Replicate status:
      Gi0/2/0/1: success 
      Gi0/3/0/1: pending
      Gi0/4/0/1: failed
    MTU 1500; interworking none
    Statistics:
      packets: received 0, sent 0
      bytes: received 0, sent 0
  PW: neighbor 130.130.130.130, PW ID 1234, state is down ( provisioned )
    PW class not set
    Encapsulation MPLS, protocol LDP
    PW type Ethernet VLAN, control word disabled, interworking none
    Sequencing not set
    Internal label: 16008
    VLAN id imposed: 101

      MPLS         Local                          Remote                        
      ------------ ------------------------------ -----------------------------
      Label        16001                          unknown                       
      Group ID     0x2000600                      0x0                           
      Interface    PW-Ether1       				   unknown                       
      MTU          1500                           unknown                       
      Control word disabled                       unknown                       
      PW type      Ethernet VLAN                  unknown                       
      VCCV CV type 0x2                            0x0                           
                                                  (none)                        
                   (LSP ping verification)                                      
      VCCV CC type 0x6                            0x0                           
                                                  (none)                        
                   (router alert label)                                         
                   (TTL expiry)                                                 
      ------------ ------------------------------ -----------------------------
    MIB cpwVcIndex: 2
    Create time: 19/02/2010 23:13:01 (1w2d ago)
    Last time status changed: 19/02/2010 23:13:16 (1w2d ago)
    Statistics:
      packets: received 0, sent 0
      bytes: received 0, sent 0

This example shows the sample output of a configured flow label:


RP/0/RP0/CPU0:router#  show l2vpn xconnect detail
Group g1, XC p1, state is up; Interworking none
  AC: GigabitEthernet0/0/1/1, state is up
    Type Ethernet
    MTU 1500; XC ID 0x1000002; interworking none
    Statistics:
      packets: received 24688, sent 24686
      bytes: received 1488097, sent 1487926
  PW: neighbor 192.168.0.1, PW ID 2, state is up ( established )
    PW class class1, XC ID 0x1000002
    Encapsulation MPLS, protocol LDP
    PW type Ethernet, control word disabled, interworking none
    PW backup disable delay 0 sec
Sequencing not set
Flow label flags configured (Rx=1,Tx=1), negotiated (Rx=0,Tx=1)

This table describes the significant fields shown in the display.

Table 8. show l2vpn xconnect Command Field Descriptions
Field	Description
XConnect Group	Displays a list of all configured cross-connect groups.
Group	Displays the cross-connect group number.
Name	Displays the cross-connect group name.
Description	Displays the cross-connect group description. If no description is configured, the interface type is displayed.
ST	State of the cross-connect group: up (UP) or down (DN).

Related Commands

Command	Description
xconnect group	Configures cross-connect groups.

show tech-support l2vpn platform no-statistics

To automatically run show commands that display information specific to Layer 2 Virtual Private Network (L2VPN) platform without debugging statistics, use the show tech-support l2vpn platform no-statistics command in the EXEC mode.

show tech-support l2vpn platform no-statistics [ file | list-CLIs | location | rack]

Syntax Description


file	Specifies that the command output is saved to a specified file.
list-CLIs	Specifies the list of CLIs but not executed.
location	Specifies a location.
rack	Specifies a rack.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 6.3.2	This command was introduced.

Usage Guidelines

This command collects information for Layer 2 VPN platform related issues that is useful for Cisco Technical Support representatives when troubleshooting a router.

Note

The show tech-support l2vpn platform command does not collect all bridge domains information when there is large scale values associated with bridge domains. Hence, use the show tech-support l2vpn platform no-statistics command.

Task ID


Task ID	Operation
l2vpn	read

Examples

The following example shows the output of show tech-support l2vpn platfrom no-statistics command.

RP/0/RP0/CPU0:router#show tech-support l2vpn platfrom no-statistics

Tue Jan  8 02:40:56.007 UTC
++ Show tech start time: 2019-Jan-08.024056.UTC ++
Tue Jan 08 02:40:56 UTC 2019 Waiting for gathering to complete
..............................
Tue Jan 08 02:43:03 UTC 2019 Compressing show tech output
Show tech output available at 0/RSP1/CPU0 : /net/node0_RSP1_CPU0/harddisk:/showtech/showtech-RR-l2vpn_platform-2019-Jan-08.024056.UTC.tgz
++ Show tech end time: 2019-Jan-08.024303.UTC ++

show tunnel-template

To display tunnel template information, use the show tunnel-template command in the EXEC mode.

show tunnel-template template-name

Syntax Description


`template-name`	Name of the tunnel template.

Command Default

None

Command Modes

EXEC

Command History


Release	Modification
Release 3.5.0	This command was introduced.

Usage Guidelines

Task ID


Task ID	Operation
tunnel	read

Examples

The following example shows the output of the show tunnel-template test command for Local PE Tunnel:


RP/0/RP0/CPU0:router# show tunnel-template test
Fri Jan 30 06:22:46.428 UTC

Tunnel template
------------------------------------------------------
Name:       test (ifhandle: 0x00080030)
MTU:        1464
TTL:        255
TOS:        0
Tunnel ID:  1
Source:     25.25.25.25
Session ID: 0x1D174108 Cookie: 8 bytes [0x24FD3ADAA4485333] being rolled into
    Session ID: 0x15A86E93 Cookie: 8 bytes [0xF486195660CCD522]
Next Session-id/Cookie rollover happens in 1 minute 49 seconds
Transmit:        14213298 pkts  1250770344 bytes
Cookie Mismatch: 0 pkts
MTU Violation:   0 pkts

The following example shows the output of the show tunnel-template test command for Remote PE Tunnel:


RP/0/RP0/CPU0:router# show tunnel-template test
Fri Jan 30 06:04:29.800 UTC

Tunnel template
------------------------------------------------------
Name:       test (ifhandle: 0x00080030)
MTU:        600
TTL:        255
TOS:        0
Tunnel ID:  1
Source:     35.35.35.35    Address Pool: 36.36.36.0/28
Session ID: 0x111F4312 Cookie: 8 bytes [0xB95A806145BE9BE7]
Transmit:        122168722 pkts  10750845295 bytes
Cookie Mismatch: 0 pkts
MTU Violation:   0 pkts

Related Commands

Command	Description
tunnel-template	Enters tunnel-template configuration submode.

source (p2p)

To configure source IPv6 address of the pseudowire, use the source command in p2p pseudowire configuration mode. To disable the source IPv6 address configuration, use the no form of this command.

source ipv6_address

no source ipv6_address

Syntax Description


`ipv6_address`	Source IPv6 address of pseudowire

Command Default

None

Command Modes

p2p pseudowire configuration

Command History


Release	Modification
Release 4.3.1	This command was introduced

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Note

All L2VPN configurations can be deleted using the no l2vpn command.

Task ID


Task ID	Operation
l2vpn	read, write

Examples

This example shows how to set a source IPv6 address to a point-to-point IPv6 cross-connect:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# xconnect group g1
RP/0/RP0/CPU0:router(config-l2vpn-xc)# p2p xc3
RP/0/RP0/CPU0:router(config-l2vpn-xc-p2p)# interface GigabitEthernet0/0/0/4.2
RP/0/RP0/CPU0:router(config-l2vpn-xc-p2p)# neighbor ipv6 1111:2222::cdef pw-id 1
RP/0/RP0/CPU0:router(config-l2vpn-xc-p2p-pw)# source 1111:2222::abcd

Related Commands

Command	Description
p2p	Enters p2p configuration submode to configure point-to-point cross-connects.
neighbor (L2VPN)	Configures a pseudowire for a cross-connect.

storm-control

Storm control on ASR 9000 Series Routers can be applied at the following service attachment points:

Bridge domain (BD)
Attachment Circuit (AC)
Access pseudowire (PW)

To enable storm control on all access circuits (AC) and access pseudowires (PW) in a VPLS bridge, use the storm-control command in l2vpn bridge group bridge-domain configuration mode. To disable storm control, use the no form of this command.

To enable storm control on an access circuit (AC) under a VPLS bridge, use the storm-control command in l2vpn bridge group bridge-domain access circuit configuration mode. To disable storm control, use the no form of this command.

To enable storm control on an access pseudowire (PW) in a VPLS bridge, use the storm-control command in l2vpn bridge group bridge-domain neighbor configuration mode. To disable storm control, use the no form of this command.

storm-control {broadcast | multicast | unknown-unicast} { pps pps-value | kbps kbps-value}

no storm-control {broadcast | multicast | unknown-unicast} { pps pps-value | kbps kbps-value}

Syntax Description


broadcast	Configures storm control for broadcast traffic.
multicast	Configures storm control for multicast traffic.
unknown-unicast	Configures storm control for unknown unicast traffic. Storm control does not apply to bridge protocol data unit (BPDU) packets. All BPDU packets are processed as if traffic storm control is not configured. Storm control does not apply to internal communication and control packets, route updates, SNMP management traffic, Telnet sessions, or any other packets addressed to the router.
pps `pps-value`	Configures the packets-per-second (pps) storm control threshold for the specified traffic type. Valid values range from 1 to 160000.
kbps `kbps-value`	Configures the storm control in kilo bits per second (kbps). The range is from 64 to 1280000.

Command Default

Storm control is disabled by default.

Command Modes

l2vpn bridge group bridge-domain access circuit configuration

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

Bridge Protocol Data Unit (BPDU) packets are not filtered through the storm control feature.
The traffic storm control monitoring interval is set in the hardware and is not configurable. On Cisco ASR 9000 Series Router, the monitoring interval is always one second.
When there is a mix of kbps and pps storm control on bridge or bridge port, the pps value is translated to kbps inside the policer using 1000 bytes per packet as an average.
The hardware can only be programmed with a granularity of 8 pps, so values are not divisible by eight. These are rounded to the nearest increment of eight.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example enables storm control thresholds throughout the bridge domain:


RP/0/RSP0/CPU0:a9k1# configure
RP/0/RSP0/CPU0:a9k1(config)# l2vpn
RP/0/RSP0/CPU0:a9k1(config-l2vpn)# bridge group BG1
RP/0/RSP0/CPU0:a9k1(config-l2vpn-bg)# bridge-domain BD1
RP/0/RSP0/CPU0:a9k1(config-l2vpn-bg-bd)# storm-control unknown-unicast pps 100
RP/0/RSP0/CPU0:a9k1(config-l2vpn-bg-bd)# storm-control multicast pps 100
RP/0/RSP0/CPU0:a9k1(config-l2vpn-bg-bd)# storm-control broadcast pps 100

The following example enables storm control thresholds on an access circuit:

RP/0/RSP0/CPU0:a9k1# configure
RP/0/RSP0/CPU0:a9k1(config)# l2vpn
RP/0/RSP0/CPU0:a9k1(config-l2vpn)# bridge group BG1
RP/0/RSP0/CPU0:a9k1(config-l2vpn-bg-bd)# bridge-domain BD2
RP/0/RSP0/CPU0:a9k1(config-l2vpn-bg-bd)# interface Bundle-Ether9001.2001
RP/0/RSP0/CPU0:a9k1(config-l2vpn-bg-bd-ac)# storm-control unknown-unicast pps 100
RP/0/RSP0/CPU0:a9k1(config-l2vpn-bg-bd-ac)# storm-control multicast pps 100
RP/0/RSP0/CPU0:a9k1(config-l2vpn-bg-bd-ac)# storm-control broadcast pps 100

The following example enables storm control thresholds on an access pseudowire:

RP/0/RSP0/CPU0:a9k1# configure
RP/0/RSP0/CPU0:a9k1(config)# l2vpn
RP/0/RSP0/CPU0:a9k1(config-l2vpn)# bridge group BG1
RP/0/RSP0/CPU0:a9k1(config-l2vpn-bg-bd)# bridge-domain BD2
RP/0/RSP0/CPU0:a9k1(config-l2vpn-bg-bd-ac)# neighbor 10.1.1.1 pw-id 20011001
RP/0/RSP0/CPU0:a9k1(config-l2vpn-bg-bd-pw)# storm-control unknown-unicast pps 100
RP/0/RSP0/CPU0:a9k1(config-l2vpn-bg-bd-pw)# storm-control multicast pps 100
RP/0/RSP0/CPU0:a9k1(config-l2vpn-bg-bd-pw)# storm-control broadcast pps 100
RP/0/RSP0/CPU0:a9k1(config-l2vpn-bg-bd-pw)# commit

Running Configuration

l2vpn
 bridge group BG1
  bridge-domain BD1
   storm-control unknown-unicast pps 100
   storm-control multicast pps 100
   storm-control broadcast pps 100
  !
  bridge-domain BD2
   interface Bundle-Ether9001.2001
    storm-control unknown-unicast pps 100
    storm-control multicast pps 100
    storm-control broadcast pps 100
   !
   neighbor 10.1.1.1 pw-id 20011001
    storm-control unknown-unicast pps 100
    storm-control multicast pps 100
    storm-control broadcast pps 100
   !
  !
 !
!
end
RP/0/RSP0/CPU0:a9k1(config)#

tag-impose

To specify a tag for a VLAN ID configuration, use the tag-impose command in l2vpn configuration submode. To remove the tag, use the no form of this command.

tag-impose vlan value

no tag-impose vlan value

Syntax Description


vlan	VLAN in tagged mode.
`value`	Tag value. The range is from 1 to 4094. The default value is 0.

Command Default

None

Command Modes

L2VPN configuration

Command History


Release	Modification
Release 4.2.1	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

This example shows how to specify a tag for a VLAN:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# xconnect group xc1
RP/0/RP0/CPU0:router(config-l2vpn-xc)#p2p grp1
RP/0/RP0/CPU0:router(config-l2vpn-xc-p2p)#neighbor 10.1.1.2 pw-id 78
RP/0/RP0/CPU0:router(config-l2vpn-xc-p2p-pw)#tag-impose vlan 8

Related Commands

Command	Description
pw-class (L2VPN)	Enters pseudowire class submode to define a pseudowire class template.

tag-rewrite

To configure VLAN tag rewrite, use the tag-rewrite command in Encapsulation MPLS configuration mode. To disable VLAN tag rewrite, use the no form of this command.

tag-rewrite ingress vlan vlan-id

no tag-rewrite ingress vlan vlan-id

Syntax Description


ingress	Configures ingress mode.
vlan	Configures VLAN tagged mode
`vlan-id`	Specifies the value of the ID of the VLAN.

Command Default

None

Command Modes

Encapsulation MPLS configuration

Command History


Release	Modification
Release 3.6.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

The tag-rewrite command is applicable only to pseudowires with MPLS encapsulation.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to configure preferred-path tunnel settings:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# pw-class kanata01
RP/0/RP0/CPU0:router(config-l2vpn-pwc)# encapsulation mpls
RP/0/RP0/CPU0:router(config-l2vpn-pwc-encap-mpls)# tag-rewrite vlan 2000
RP/0/RP0/CPU0:router(config-l2vpn-pwc-encap-mpls)#

Related Commands

Command	Description
show l2vpn xconnect	Displays brief information on configured cross-connects.

timeout setup (L2TP)

To configure timeout definitions for L2TP session setup, use the timeout setup command in L2TP class configuration mode. To return to the default behavior, use the no form of this command.

timeout setup seconds

no timeout setup seconds

Syntax Description


`seconds`	Time, in seconds, to setup a control channel. Range is 60 to 6000 seconds. Default is 300 seconds.

Command Default

seconds : 300

Command Modes

L2TP class configuration

Command History


Release	Modification
Release 3.9.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to configure a timeout value for L2TP session setup of 400 seconds:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2tp-class cisco 
RP/0/RP0/CPU0:router(config-l2tp-class)# timeout setup 400

Related Commands

Command	Description
authentication (L2TP)	Enables L2TP authentication for a specified L2TP class name.
hello-interval (L2TP)	Configures the hello-interval value for L2TP (duration between control channel hello packets).
hidden (L2TP)	Enables hidden attribute-value pairs (AVPs).
hostname (L2TP)	Defines the name used in the L2TP hostname AVP.
l2tp-class	Enters L2TP class configuration mode where you can define an L2TP signaling template.
password (L2TP)	Defines the password and password encryption type for control channel authentication.
receive-window (L2TP)	Configures the receive window size for the L2TP server.
retransmit (L2TP)	Configures retransmit retry and timeout values.
show l2tp session	Displays information about L2TP sessions.
show l2tp tunnel	Displays information about L2TP tunnels.

tos (l2vpn)

To configure Type of Service (TOS) reflection or to set TOS value, use the tos command in L2VPN pseudowire class encapsulation L2TPv3 configuration mode. To reset the TOS value, use the no form of this command.

tos {reflect [value tos value] | value tos value [reflect]}

no tos {reflect [value tos value] | value tos value [reflect]}

Syntax Description


reflect	Enables TOS reflection.
value	Sets the TOS value for L2TPv3 pseudowire class.
`tos value`	Value of the TOS.

Command Default

By default, the TOS is copied over, from the class of service (COS) fields of the VLAN header. If the underlying packet is not an IPv4 or IPv6 packet, the COS fields are copied from the VLAN header, even if TOS reflection is configured.

Command Modes

L2VPN pseudowire class encapsulation L2TPv3 configuration

Command History


Release	Modification
Release 4.3.1	This command was introduced

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Note

All L2VPN configurations can be deleted using the no l2vpn command.

Task ID


Task ID	Operation
l2vpn	read, write

Examples

This example shows how to configure TOS reflection:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# pw-class kanata01
RP/0/RP0/CPU0:router(config-l2vpn-pwc)# encapsulation l2tpv3
RP/0/RP0/CPU0:router(config-l2vpn-pwc-l2tpv3)# protocol l2tpv3
RP/0/RP0/CPU0:router(config-l2vpn-pwc-l2tpv3)# tos reflect

The following example shows how to set a TOS value:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# pw-class kanata01
RP/0/RP0/CPU0:router(config-l2vpn-pwc)# encapsulation l2tpv3
RP/0/RP0/CPU0:router(config-l2vpn-pwc-l2tpv3)# protocol l2tpv3
RP/0/RP0/CPU0:router(config-l2vpn-pwc-l2tpv3)# tos value 64

Related Commands

Command	Description
pw-class (L2VPN)	Enters pseudowire class submode to define a pseudowire class template.
pw-class encapsulation l2tpv3	Configures L2TPv3 pseudowire encapsulation.

transport mode (L2VPN)

To configure L2VPN pseudowire class transport mode, use the transport mode command in L2VPN pseudowire class MPLS encapsulation mode. To disable the L@VPN pseudowire class transport mode configuration, use the no form of this command.

transport mode {ethernet | vlan }

no transport mode {ethernet | vlan }

Syntax Description


ethernet	Configures Ethernet port mode.
vlan	Configures VLAN tagged mode.

Command Default

None

Command Modes

L2VPN pseudowire class MPLS encapsulation

Command History


Release	Modification
Release 3.7.2	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Note

All L2VPN configurations can be deleted using the no l2vpn command.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

This example shows how to configure Ethernet transport mode:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# pw-class kanata01
RP/0/RP0/CPU0:router(config-l2vpn-pw)# encapsulation mpls
RP/0/RP0/CPU0:router(config-l2vpn-encap-mpls)# transport-mode ethernet

Related Commands

Command	Description
pw-class (L2VPN)	Enters pseudowire class submode to define a pseudowire class template.

transport mode vlan passthrough

To configure L2VPN bridge domain transport mode, use the transport mode vlan passthrough command in L2VPN bridge domain configuration mode. To disable the L2VPN bridge domain transport mode configuration, use the no form of this command.

transport mode vlan passthrough

no transport mode vlan passthrough

Syntax Description

This command has no keywords or arguments.

Command Default

None

Command Modes

L2VPN bridge domain configuration

Command History


Release	Modification
Release 4.3.1	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Note

All L2VPN configurations can be deleted using the no l2vpn command.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

This example shows how to configure transport mode vlan passthrough:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# bridge group bg1
RP/0/RP0/CPU0:router(config-l2vpn-bg)# bridge-domain bd1
RP/0/RP0/CPU0:router(config-l2vpn-bg-bd)# transport mode vlan passthrough

Related Commands

Command	Description
bridge-domain (VPLS)	Establishes a bridge domain, and enters L2VPN bridge group bridge domain configuration mode.

ttl (l2vpn)

To configure Time to Live (TTL) for Pseudowire class, use the ttl command in L2VPN pseudowire class encapsulation L2TPv3 configuration mode. To disable the TTL configuration, use the no form of this command.

ttl ttl _value

no ttl ttl_value

Syntax Description


`ttl_value`	The TTL Value. Range is from 1 to 255.

Command Default

None

Command Modes

L2VPN pseudowire class encapsulation L2TPv3 configuration

Command History


Release	Modification
Release 4.3.1	This command was introduced

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Note

All L2VPN configurations can be deleted using the no l2vpn command.

Task ID


Task ID	Operation
l2vpn	read, write

Examples

This example shows how to configure TTL:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# pw-class kanata01
RP/0/RP0/CPU0:router(config-l2vpn-pwc)# encapsulation l2tpv3
RP/0/RP0/CPU0:router(config-l2vpn-pwc-l2tpv3)# protocol l2tpv3
RP/0/RP0/CPU0:router(config-l2vpn-pwc-l2tpv3)# ttl 40

Related Commands

Command	Description
pw-class (L2VPN)	Enters pseudowire class submode to define a pseudowire class template.
pw-class encapsulation l2tpv3	Configures L2TPv3 pseudowire encapsulation.

tunnel-template

To enter tunnel-template configuration submode, use the tunnel-template command in global configuration mode.

tunnel-template template name

no tunnel-template template-name

Syntax Description


`template-name`	Configures a name for the tunnel template.

Command Default

None

Command Modes

Global configuration

Command History


Release	Modification
Release 3.5.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Task ID


Task ID	Operations
tunnel	read, write

Examples

The following example shows how to enter tunnel-template configuration submode:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# tunnel-template template_01

Related Commands

Command	Description
xconnect group	Configures cross-connect groups.

vpws-seamless-integration

To enable EVPN-VPWS seamless integration, use the vpws-seamless-integration command in L2VPN configuration mode. To disable EVPN-VPWS seamless integration, use the no form of this command.

vpws-seamless-integration

Syntax Description

This command has no arguments or keywords.

Command Default

None

Command Modes

L2VPN configuration mode

Command History


Release	Modification
Release 7.4.1	This command was introduced.

Usage Guidelines

No specific guidelines impact the use of this command.

Task ID


Task ID	Operations
L2VPN	read, write

Examples

The following example shows how to enable EVPN-VPWS integration on an edge device for BGP PW.


Router# configure
Router(config)# l2vpn xconnect group 1
Router(config-l2vpn-xc)# mp2mp 2
Router(config-l2vpn-xc-mp2mp)# autodiscovery bgp
Router(config-l2vpn-xc-mp2mp-ad)# signaling-protocol bgp
Router(config-l2vpn-xc-mp2mp-ad-sig)# ce-id 3
Router(config-l2vpn-xc-mp2mp-ad-sig-ce)# vpws-seamless-integration
Router(config-l2vpn-xc-mp2mp-ad-sig-ce)#

The following example shows how to enable EVPN-VPWS integration for TLDP PW.


Router# configure
Router(config)# l2vpn xconnect group 1
Router(config-l2vpn-xc)# p2p p1
Router(config-l2vpn-xc-p2p)# interface BE1.1
Router(config-l2vpn-xc-p2p)# neighbor 1.1.1.1 pw-id 1
Router(config-l2vpn-xc-p2p)# vpws-seamless-integration

xconnect group

To configure cross-connect groups, use the xconnect group command in L2VPN configuration mode. To return to the default behavior, use the no form of this command.

xconnect group group-name

no xconnect group group-name

Syntax Description


`group-name`	Configures a cross-connect group name using a free-format 32-character string.

Command Default

None

Command Modes

L2VPN configuration

Command History


Release	Modification
Release 3.4.0	This command was introduced.

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator for assistance.

Note

You can configure up to a maximum of 16K cross-connects per box.

Task ID


Task ID	Operations
l2vpn	read, write

Examples

The following example shows how to group all cross -connects for customer_atlantic:


RP/0/RP0/CPU0:router# configure
RP/0/RP0/CPU0:router(config)# l2vpn
RP/0/RP0/CPU0:router(config-l2vpn)# xconnect group customer_atlantic

Related Commands

Command	Description
show l2vpn xconnect	Displays brief information on configured cross-connects.

Bias-Free Language

Results

Chapter: Virtual Private Network Commands

Virtual Private Network Commands

advertise-mac

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Examples

authentication (L2TP)

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Task ID

Examples

Related Commands

backup disable (L2VPN)

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Task ID

Examples

Related Commands

clear l2route evpn ipv4

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Task ID

Examples

clear l2route evpn ipv6

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Task ID

Examples

clear l2route evpn mac

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Task ID

Examples

clear l2tp counters control session

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Task ID

Examples

Related Commands

clear l2tp counters control tunnel

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Task ID

Examples

Related Commands

clear l2tp tunnel

Syntax Description

Command Default

Command Modes

Command History

Usage Guidelines

Task ID

Examples