This chapter contains the following sections:

The router provides a robust environment-monitoring system with several sensors that monitor the system temperatures. The following are some of the key functions of the environmental monitoring system:

• Monitoring temperature of CPUs and Motherboard

• Recording abnormal events and generating notifications

• Monitoring Simple Network Management Protocol (SNMP) traps

• Generating and collecting Onboard Failure Logging (OBFL) data

• Sending call home event notifications

• Logging system error messages

• Displaying present settings and status

Monitoring and reporting functions allow you to maintain normal system operation by identifying and resolving adverse conditions prior to loss of operation.

• Environmental Monitoring Functions

• Environmental Reporting Functions

Environmental monitoring functions use sensors to monitor the temperature of the cooling air as it moves through the chassis.

The router is expected to meet the following environmental operating conditions

• Non-operating Temperature: -40F to +185F (-40C to +85C)

• Non-operating Humidity: 5 to 95% relative humidity (non-condensing)

• Operating Temperature:

  -40F to +185F (-40C to +85C) as measured at the center of the top surface of the –CON SKU thermal plate.

  Temperature range of a completed solution depends on the enclosure thermal design characteristics used by the integrator.

  If –NCP SKU is used, integrator is responsible for designing a thermal solution that meets the component level requirements provided in this document.

• Operating Humidity: 95% +/- 5% RH

• Operating Altitude: -15,000ft (4,572m)

The following table displays the levels of status conditions used by the environmental monitoring system.

The environmental monitoring system sends system messages to the console, for example, when the conditions described here are met:

Warnings :
--------
For all the temperature sensors (name starting with “Temp:”) above,
the critical warning threshold is 100C (100C and higher)
the warning threshold is 80C (range from 80C to 99C)
the low warning threshold is 1C (range from -inf to 1C).
 
For all voltage sensors (names starting with "V:"),
the high warning threshold starts at that voltage +10%. (voltage + 10% is warning)
the low warning threshold starts at the voltage -10%. (voltage - 10% is warning)

You can retrieve and display environmental status reports using the following commands:

• show diag all eeprom

• show environment

• show environment all

• show inventory

• show platform

• show platform diag

• show platform software status control-processor

• show diag slot R0 eeprom detail

• show version

• show power

These commands show the current values of parameters such as temperature and voltage.

The environmental monitoring system updates the values of these parameters every 60 seconds. Brief examples of these commands are shown below:

Router#show diag all eeprom
MIDPLANE EEPROM data:

Product Identifier (PID) : ESR-6300-NCP-K9
Version Identifier (VID) : V00
PCB Serial Number : FOC23032UUN
Top Assy. Revision : 01
Hardware Revision : 0.2
Asset ID :
CLEI Code : UNASSIGNED
External PoE Module POE0 EEPROM data is not initialized

Internal PoE is not present

Slot R0 EEPROM data:

Product Identifier (PID) : ESR-6300-NCP-K9
Version Identifier (VID) : V00
PCB Serial Number : FOC23032UUN
Top Assy. Revision : 01
Hardware Revision : 0.2
CLEI Code : UNASSIGNED
Slot F0 EEPROM data:

Product Identifier (PID) : ESR-6300-NCP-K9
Version Identifier (VID) : V00
PCB Serial Number : FOC23032UUN
Top Assy. Revision : 01
Hardware Revision : 0.2
CLEI Code : UNASSIGNED
Slot 0 EEPROM data:

Product Identifier (PID) : ESR-6300-NCP-K9
Version Identifier (VID) : V00
PCB Serial Number : FOC23032UUN
Top Assy. Revision : 01
Hardware Revision : 0.2
CLEI Code : UNASSIGNED
SPA EEPROM data for subslot 0/0:

Product Identifier (PID) : ESR-6300-2x1GE
Version Identifier (VID) : V01
PCB Serial Number :
Top Assy. Part Number : 68-2236-01
Top Assy. Revision : A0
Hardware Revision : 2.2
CLEI Code : CNUIAHSAAA
SPA EEPROM data for subslot 0/1:

Product Identifier (PID) : ESR-6300-ES-4
Version Identifier (VID) : V01
PCB Serial Number :
Top Assy. Part Number : 68-2236-01
Top Assy. Revision : A0
Hardware Revision : 2.2
CLEI Code : CNUIAHSAAA
SPA EEPROM data for subslot 0/2 is not available

SPA EEPROM data for subslot 0/3 is not available

SPA EEPROM data for subslot 0/4 is not available

SPA EEPROM data for subslot 0/5 is not available

Router#show environment
Number of Critical alarms: 0
Number of Major alarms: 0
Number of Minor alarms: 0

Slot Sensor Current State Reading Threshold(Minor,Major,Critical,Shutdown)
---------- -------------- --------------- ------------ ---------------------------------------
R0 Temp: LM75BXXX Normal 45 Celsius (75 ,80 ,90 ,na )(Celsius)

Router#show environment all
Sensor List: Environmental Monitoring
Sensor Location State Reading
Temp: LM75BXXX R0 Normal 45 Celsius

Router#show inventory
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
INFO: Please use "show license UDI" to get serial number for licensing.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

NAME: "Chassis", DESCR: "Embedded Services Router with 2 Gigabit Ethernet routed ports,4 Gigabit Ethernet switched ports, no cooling plate"
PID: ESR-6300-NCP-K9 , VID: V00 , SN: FOC23032UUN

NAME: "Power Supply Module 0", DESCR: "External Power Supply Module"
PID: PWR-12V , VID: , SN:

NAME: "module 0", DESCR: "Cisco ESR-6300-NCP-K9 Fixed and pluggable Interface Module controller"
PID: ESR-6300-NCP-K9 , VID: , SN:

NAME: "NIM subslot 0/1", DESCR: "ESR-6300-ES-4"
PID: ESR-6300-ES-4 , VID: V01 , SN:

NAME: "NIM subslot 0/0", DESCR: "Front Panel 2 port Gigabitethernet Module"
PID: ESR-6300-2x1GE , VID: V01 , SN:

NAME: "module R0", DESCR: "Cisco ESR-6300-NCP-K9 Route Processor"
PID: ESR-6300-NCP-K9 , VID: V00 , SN: FOC23032UUN

NAME: "module F0", DESCR: "Cisco ESR-6300-NCP-K9 Forwarding Processor"
PID: ESR-6300-NCP-K9 , VID: , SN:

Router#show platform
Chassis type: ESR-6300-NCP-K9

Slot Type State Insert time (ago)
--------- ------------------- --------------------- -----------------
0 ESR-6300-NCP-K9 ok 07:30:08
0/0 ESR-6300-2x1GE ok 07:29:45
0/1 ESR-6300-ES-4 ok 07:29:45
R0 ESR-6300-NCP-K9 ok, active 07:31:20
F0 ESR-6300-NCP-K9 ok, active 07:31:20
P0 PWR-12V ok 07:30:46

Router#show platform diag
Chassis type: ESR-6300-NCP-K9

Slot: 0, ESR-6300-NCP-K9
Running state : ok
Internal state : online
Internal operational state : ok
Physical insert detect time : 00:01:45 (07:30:11 ago)
Software declared up time : 00:01:16 (07:30:40 ago)
CPLD version :
Firmware version : 2.1(DEV) [vitu-vitu 127]

Sub-slot: 0/0, ESR-6300-2x1GE
Operational status : ok
Internal state : inserted
Physical insert detect time : 00:02:07 (07:29:49 ago)
Logical insert detect time : 00:02:07 (07:29:49 ago)

Sub-slot: 0/1, ESR-6300-ES-4
Operational status : ok
Internal state : inserted
Physical insert detect time : 00:02:07 (07:29:49 ago)
Logical insert detect time : 00:02:07 (07:29:49 ago)

Slot: R0, ESR-6300-NCP-K9
Running state : ok, active
Internal state : online
Internal operational state : ok
Physical insert detect time : 00:00:33 (07:31:24 ago)
Software declared up time : 00:00:33 (07:31:24 ago)
CPLD version : 00000000
Firmware version : 2.1(DEV) [vitu-vitu 127]

Slot: F0, ESR-6300-NCP-K9
Running state : ok, active
Internal state : online
Internal operational state : ok
Physical insert detect time : 00:00:33 (07:31:24 ago)
Software declared up time : 00:01:42 (07:30:14 ago)
Hardware ready signal time : 00:00:00 (never ago)
Packet ready signal time : 00:01:45 (07:30:11 ago)
CPLD version : 00000000
Firmware version : 2.1(DEV) [vitu-vitu 127]

Slot: P0, PWR-12V
State : ok
Physical insert detect time : 00:01:06 (07:30:50 ago)

Slot: GE-POE, Unknown
State : NA
Physical insert detect time : 00:00:00 (never ago)

Router# show platform software status control-processor
RP0: online, statistics updated 9 seconds ago
Load Average: healthy
1-Min: 0.32, status: healthy, under 5.00
5-Min: 0.33, status: healthy, under 5.00
15-Min: 0.35, status: healthy, under 5.00
Memory (kb): healthy
Total: 3959840
Used: 2894588 (73%), status: healthy
Free: 1065252 (27%)
Committed: 2435656 (62%), under 90%
Per-core Statistics
CPU0: CPU Utilization (percentage of time spent)
User: 0.50, System: 0.91, Nice: 0.00, Idle: 98.07
IRQ: 0.40, SIRQ: 0.10, IOwait: 0.00
CPU1: CPU Utilization (percentage of time spent)
User: 0.81, System: 0.30, Nice: 0.00, Idle: 98.48
IRQ: 0.20, SIRQ: 0.20, IOwait: 0.00
CPU2: CPU Utilization (percentage of time spent)
User: 0.81, System: 2.65, Nice: 0.00, Idle: 95.41
IRQ: 1.12, SIRQ: 0.00, IOwait: 0.00
CPU3: CPU Utilization (percentage of time spent)
User: 7.66, System: 17.05, Nice: 0.00, Idle: 70.58
IRQ: 4.59, SIRQ: 0.10, IOwait: 0.00
Router#
 

Router#show diag slot R0 eeprom detail
Slot R0 EEPROM data:

EEPROM version : 4
Compatible Type : 0xFF
Controller Type : 3497
Hardware Revision : 0.2
PCB Part Number : 73-101841-01
Board Revision : 07
Deviation Number : 0
Fab Version : 01
PCB Serial Number : FOC23032UUN
Top Assy. Part Number : 068-102311-01
Top Assy. Revision : 01
Chassis Serial Number : FOC23032UUN
Deviation Number : 0
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product Identifier (PID) : ESR-6300-NCP-K9
Version Identifier (VID) : V00
CLEI Code : UNASSIGNED
Manufacturing Test Data : 00 00 00 00 00 00 00 00
Field Diagnostics Data : 00 00 00 00 00 00 00 00
Chassis MAC Address : d478.9b5c.d680
MAC Address block size : 128
Asset ID :
Asset Alias :
Unknown Field (type 0086): 00 00 00 00
Asset ID :

Router# show version
Cisco IOS XE Software, Version 17.01.01
Cisco IOS Software [Amsterdam], ISR Software (ARMV8EL_LINUX_IOSD-UNIVERSALK9_IOT-M), Version 17.1.1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2019 by Cisco Systems, Inc.
Compiled Tue 19-Nov-19 06:19 by mcpre


Cisco IOS-XE software, Copyright (c) 2005-2019 by cisco Systems, Inc.
All rights reserved.  Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0.  The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY.  You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0.  For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.


ROM: IOS-XE ROMMON

Router uptime is 1 day, 49 minutes
Uptime for this control processor is 1 day, 51 minutes
System returned to ROM by reload
System image file is "bootflash:c6300-universalk9.17.01.01.SPA.bin"
Last reload reason: Reload Command



This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.


Technology Package License Information: 
          
-----------------------------------------------------------------
Technology    Technology-package           Technology-package
              Current       Type           Next reboot  
------------------------------------------------------------------
network-stack    network-advantage   Smart License    network-advantage
dna-stack        dna-advantage       Smart License    dna-advantage

The current throughput level is 250000 kbps 


Smart Licensing Status: UNREGISTERED/EVAL MODE

cisco ESR-6300-CON-K9 (1RU) processor with 705559K/6147K bytes of memory.
Processor board ID FOC233501BF
MCU bootloader version: 8
MCU application version: 10
1 Virtual Ethernet interface
6 Gigabit Ethernet interfaces
32768K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
60542080K bytes of USB Flash at usbflash0:.
6500351K bytes of Bootflash at bootflash:.

Configuration register is 0x2102

Router# show power
Main PSU :
Total Power Consumption from 3.3V Line : 0.34
Total Power Consumption from 5V Line : 6.64
Configured Mode : N/A
Current runtime state same : N/A
PowerSupplySource : External PS
POE Module :
Configured Mode : N/A
Current runtime state same : N/A
Total power available : 120 Watts

Support has been added for SNMP MIB to be able to return values from temperature sensors. The output should look similar to the show environment CLI.

The output of a show environment on an IR1101:

IR1101#show environment

Number of Critical alarms:  0
Number of Major alarms:     0
Number of Minor alarms:     0

 Slot        Sensor          Current State   Reading        Threshold(Minor,Major,Critical,Shutdown)
 ----------  --------------  --------------- ------------   ---------------------------------------
 R0          Temp: TS1       Normal          42    Celsius      (75 ,80 ,90 ,na )(Celsius)
 R0          Temp: TS2       Normal          37    Celsius      (75 ,80 ,90 ,na )(Celsius)

The output from an snmpwalk would look similar to this:

[root@sg-centos-hv ~]# snmpwalk -v 2c -c public 33.33.33.204 1.3.6.1.4.1.9.9.13.1.3.1
SNMPv2-SMI::enterprises.9.9.13.1.3.1.2.1 = STRING: "Sensor 1"
SNMPv2-SMI::enterprises.9.9.13.1.3.1.3.1 = Gauge32: 48
SNMPv2-SMI::enterprises.9.9.13.1.3.1.4.1 = INTEGER: 93
SNMPv2-SMI::enterprises.9.9.13.1.3.1.5.1 = INTEGER: 0
SNMPv2-SMI::enterprises.9.9.13.1.3.1.6.1 = INTEGER: 1
SNMPv2-SMI::enterprises.9.9.13.1.3.1.7.1 = INTEGER: 0

The ciscoEnvMonTemperatureStatusEntry oid is 1.3.6.1.4.1.9.9.13.1.3.1:

• ciscoEnvMonTemperatureStatusIndex (.1)

• ciscoEnvMonTemperatureStatusDescr (.2)

• ciscoEnvMonTemperatureStatusValue (.3)

• ciscoEnvMonTemperatureThreshold (.4)

• ciscoEnvMonTemperatureLastShutdown (.5)

• ciscoEnvMonTemperatureStatus (.6)