In this task you will configure a named-SDR and allocate inventory. The inventory includes RP resources (memory and CPU) and
line
cards. You can repeat the steps to create maximum of three named-SDRs.
![](https://www.cisco.com/content/dam/en/us/td/i/templates/note.gif) Note |
The SDR boundary is defined at the line card
level. Hence, it is necessary to allocate at least one line card to each SDR. A single line card cannot be shared between
multiple SDRs.
Fabric cards are shared implicitly among named-SDRs.
|
After the
named-SDR are created, verify the VM state for each SDR.
Execute the show sdr command to check that the Status is "RUNNING" for all VMs in each SDR.
sysadmin-vm:0_RP0# show sdr
Wed Aug 17 16:01:06.626 UTC
SDR: Internet-SDR
Location IP Address Status Boot Count Time Started
-----------------------------------------------------------------------------
0/RP0/VM1 192.0.0.4 RUNNING 1 08/11/2016 00:33:12
0/RP1/VM1 192.0.4.4 RUNNING 1 08/11/2016 00:33:01
0/6/VM1 192.0.88.3 RUNNING 1 08/11/2016 00:32:48
SDR: P-SDR
Location IP Address Status Boot Count Time Started
-----------------------------------------------------------------------------
0/RP0/VM2 192.0.0.6 RUNNING 2 08/11/2016 03:24:43
0/RP1/VM2 192.0.4.6 RUNNING 2 08/11/2016 03:24:32
0/1/VM1 192.0.68.3 RUNNING 2 08/11/2016 03:25:26
SDR: VRFPE-SDR1
Location IP Address Status Boot Count Time Started
-----------------------------------------------------------------------------
0/RP0/VM3 192.0.0.8 RUNNING 2 08/11/2016 02:32:15
0/RP1/VM3 192.0.4.8 RUNNING 2 08/11/2016 02:32:23
0/0/VM1 192.0.64.3 RUNNING 2 08/11/2016 02:32:40
Execute the show vm command to check that the Status for named-SDRs is "running" at the line card and RP locations.
sysadmin-vm:0_RP0# show vm
Wed Aug 17 16:01:20.239 UTC
Location: 0/0
Id Status IP Address HB Sent/Recv
-------------------------------------------------------------
sysadmin running 192.0.64.1 NA/NA
VRFPE-SDR1 running 192.0.64.3 58375/58375
Location: 0/1
Id Status IP Address HB Sent/Recv
-------------------------------------------------------------
sysadmin running 192.0.68.1 NA/NA
P-SDR running 192.0.68.3 58360/58360
Location: 0/6
Id Status IP Address HB Sent/Recv
-------------------------------------------------------------
sysadmin running 192.0.88.1 NA/NA
Internet-SDR running 192.0.88.3 58401/58401
Location: 0/RP0
Id Status IP Address HB Sent/Recv
-------------------------------------------------------------
sysadmin running 192.0.0.1 NA/NA
Internet-SDR running 192.0.0.4 1169260/1169260
P-SDR running 192.0.0.6 1146966/1146966
VRFPE-SDR1 running 192.0.0.8 1146729/1146729
Location: 0/RP1
Id Status IP Address HB Sent/Recv
-------------------------------------------------------------
sysadmin running 192.0.4.1 NA/NA
Internet-SDR running 192.0.4.4 1167934/1167934
P-SDR running 192.0.4.6 1147031/1147031
VRFPE-SDR1 running 192.0.4.8 1146789/1146789
To view details about a specific SDR, use the show sdr <sdr-name> detail command in System Admin EXEC mode.