B Commands
This chapter describes the Cisco Nexus 1000V commands that begin with the letter, B.
bandwidth (interface)
To set the inherited and received bandwidth for an interface, use the bandwidth command. To restore the default value, use the no form of this command.
Syntax Description
Intended bandwidth, in kilobits per second. Valid values are 1 to 10000000. |
Defaults
Command Modes
Interface configuration (config-if)
Command History
|
|
---|---|
Usage Guidelines
The bandwidth command sets an informational parameter to communicate only the current bandwidth to the higher-level protocols; you cannot adjust the actual bandwidth of an interface using this command.
Note This is a routing parameter only. It does not affect the physical interface.
Examples
This example shows how to configure the bandwidth 30000 kbps:
Related Commands
|
|
---|---|
bandwidth (policy map)
To set the minimum guaranteed bandwidth for a specific traffic class in a QoS policy map, use the bandwidth command. To remove this configuration, use the no form of this command.
no bandwidth percent percentage
Syntax Description
Specify a percentage (1 - 100) of total bandwidth guaranteed. |
Defaults
Command Modes
Policy map class queuing configuration (config-pmap-c-que).
Command History
|
|
Usage Guidelines
The bandwidth command is used to control the bandwidth allocated to a class of traffic. The bandwidth command must explicitly be configured on a class, if desired. Bandwidth is configurable between 1% and 100%.
Examples
This example shows how to configure 20% minimum guaranteed bandwidth for the class_fin1 traffic class.
This example shows how to remove the configured bandwidth for the class_fin1 traffic class.
Related Commands
|
|
---|---|
Creates a class-based weighted fair queueing (CBWFQ) policy map. |
|
Assigns a class-based weighted fair queueing (CBWFQ) class to the specified policy map. |
|
banner motd
To configure a message of the day (MOTD) banner, use the banner motd command.
banner motd [ delimiting-character message delimiting-character ]
no banner motd [ delimiting-character message delimiting-character ]
Syntax Description
Defaults
“User Access Verification” is the default message of the day.
Command Modes
Command History
|
|
---|---|
Usage Guidelines
The MOTD banner is displayed on the terminal before the login prompt whenever you log in.
The message is restricted to 40 lines and 80 characters per line.
To create a multiple-line MOTD banner, press Enter before typing the delimiting character to start a new line. You can enter up to 40 lines of text.
Follow these guidelines when choosing your delimiting character:
Examples
This example shows how to configure and then display a banner message with the text, “Testing the MOTD.”
This example shows how to configure and then display a multiple-line MOTD banner:
This example shows how to revert to the default MOTD banner:
Related Commands
|
|
---|---|
boot auto-copy
To enable automatic copying of boot image files to the standby supervisor module, use the boot auto-copy command. To disable automatic copying, use the no form of this command.
Syntax Description
Defaults
Command Modes
Command History
|
|
---|---|
Usage Guidelines
When automatic copying of image files is enabled, the Cisco NX-OS software copies the image files referred to by the boot variable to the standby supervisor module. These image files must be present in local memory on the active supervisor module. For kickstart and system boot variables, only those image files that are configured for the standby supervisor module are copied.
Examples
This example shows how to enable automatic copying of boot image files to the standby supervisor module:
Related Commands
|
|
---|---|
boot kickstart
To configure the boot variable for the kickstart image, use the boot kickstart command. To clear the kickstart image boot variable, use the no form of this command.
boot kickstart [ filesystem: [ //directory ] | directory ] filename [ sup-1 ] [ sup-2 ]
Syntax Description
Defaults
Configures the kickstart boot variable for both supervisor modules.
Command Modes
Command History
|
|
---|---|
Usage Guidelines
The kickstart boot variable is used for loading software images when booting up. You must copy the kickstart image to the device before you reload.
Examples
This example shows how to configure the kickstart boot variable for both supervisor modules:
This example shows how to configure the kickstart boot variable for the active supervisor module:
This example shows how to clear the kickstart boot variable:
Related Commands
|
|
---|---|
boot system
To configure the boot variable for the system image, use the boot system command. To clear the system image boot variable, use the no form of this command.
boot system [ filesystem: [ //directory ] | directory ] filename [ sup-1 ] [ sup-2 ]
Syntax Description
Defaults
Configures the system boot variable for both supervisor modules.
Command Modes
Command History
|
|
---|---|
Usage Guidelines
The system boot variable is used for loading images when booting up. You must copy the system image to the device before you reload.
Examples
This example shows how to configure the system boot variable for both supervisor modules:
This example shows how to configure the system boot variable for the sup-1 supervisor module:
This example shows how to clear the system boot variable:
Related Commands
|
|
---|---|
Configures the boot variable for the kickstart software image. |
|
bridge-domain
To create a VXLAN and associate an identifying name to it, use the bridge-domain command. To remove a VXLAN, use the no form of this command.
Syntax Description
Defaults
Command Modes
Command History
|
|
Examples
This example shows how to create a VXLAN:
n1000v(config)# bridge-domain tenant-red
Related Commands
|
|
---|---|