Information About OSPFv2
OSPFv2 is an IETF link-state protocol (see the “Link-State Protocols” section) for IPv4 networks. An OSPFv2 router sends a special message, called a hello packet , out each OSPF-enabled interface to discover other OSPFv2 neighbor routers. Once a neighbor is discovered, the two routers compare information in the Hello packet to determine if the routers have compatible configurations. The neighbor routers attempt to establish adjacency, which means that the routers synchronize their link-state databases to ensure that they have identical OSPFv2 routing information. Adjacent routers share link-state advertisements (LSAs) that include information about the operational state of each link, the cost of the link, and any other neighbor information. The routers then flood these received LSAs out every OSPF-enabled interface so that all OSPFv2 routers eventually have identical link-state databases. When all OSPFv2 routers have identical link-state databases, the network is converged (see the “Convergence” section). Each router then uses Dijkstra’s Shortest Path First (SPF) algorithm to build its route table.
You can divide OSPFv2 networks into areas. Routers send most LSAs only within one area, which reduces the CPU and memory requirements for an OSPF-enabled router.
OSPFv2 supports IPv4.
This section includes the following topics:
Hello Packet
OSPFv2 routers periodically send Hello packets on every OSPF-enabled interface. The hello interval determines how frequently the router sends these Hello packets and is configured per interface. OSPFv2 uses Hello packets for the following tasks:
The Hello packet contains information about the originating OSPFv2 interface and router, including the assigned OSPFv2 cost of the link, the hello interval, and optional capabilities of the originating router. An OSPFv2 interface that receives these Hello packets determines if the settings are compatible with the receiving interface settings. Compatible interfaces are considered neighbors and are added to the neighbor table (see the “Neighbors” section).
Hello packets also include a list of router IDs for the routers that the originating interface has communicated with. If the receiving interface sees its own router ID in this list, then bidirectional communication has been established between the two interfaces.
OSPFv2 uses Hello packets as a keepalive message to determine if a neighbor is still communicating. If a router does not receive a Hello packet by the configured dead interval (usually a multiple of the hello interval), then the neighbor is removed from the local neighbor table.
Neighbors
An OSPFv2 interface must have a compatible configuration with a remote interface before the two can be considered neighbors. The two OSPFv2 interfaces must match the following criteria:
- Hello interval
- Dead interval
- Area ID (see the “Areas” section)
- Authentication
- Optional capabilities
If there is a match, the following information is entered into the neighbor table:
- Neighbor ID—The router ID of the neighbor.
- Priority—Priority of the neighbor. The priority is used for designated router election (see the “Designated Routers” section).
- State—Indication of whether the neighbor has just been heard from, is in the process of setting up bidirectional communications, is sharing the link-state information, or has achieved full adjacency.
- Dead time—Indication of the time since the last Hello packet was received from this neighbor.
- IP Address—The IP address of the neighbor.
- Designated Router—Indication of whether the neighbor has been declared as the designated router or as the backup designated router (see the “Designated Routers” section).
- Local interface—The local interface that received the Hello packet for this neighbor.
Adjacency
Not all neighbors establish adjacency. Depending on the network type and designated router establishment, some neighbors become fully adjacent and share LSAs with all their neighbors, while other neighbors do not. For more information, see the “Designated Routers” section.
Adjacency is established using Database Description packets, Link State Request packets, and Link State Update packets in OSPF. The Database Description packet includes just the LSA headers from the link-state database of the neighbor (see the “Link-State Database” section). The local router compares these headers with its own link-state database and determines which LSAs are new or updated. The local router sends a Link State Request packet for each LSA that it needs new or updated information on. The neighbor responds with a Link State Update packet. This exchange continues until both routers have the same link-state information.
Designated Routers
Networks with multiple routers present a unique situation for OSPF. If every router floods the network with LSAs, the same link-state information will be sent from multiple sources. Depending on the type of network, OSPFv2 might use a single router, the designated router ( DR), to control the LSA floods and represent the network to the rest of the OSPFv2 area (see the “Areas” section). If the DR fails, OSPFv2 selects a backup designated router (BDR). If the DR fails, OSPFv2 uses the BDR.
Network types are as follows:
- Point-to-point—A network that exists only between two routers. All neighbors on a point-to-point network establish adjacency and there is no DR.
- Broadcast—A network with multiple routers that can communicate over a shared medium that allows broadcast traffic, such as Ethernet. OSPFv2 routers establish a DR and BDR that controls LSA flooding on the network. OSPFv2 uses the well-known IPv4 multicast addresses 224.0.0.5 and a MAC address of 0100.5300.0005 to communicate with neighbors.
The DR and BDR are selected based on the information in the Hello packet. When an interface sends a Hello packet, it sets the priority field and the DR and BDR field if it knows who the DR and BDR are. The routers follow an election procedure based on which routers declare themselves in the DR and BDR fields and the priority field in the Hello packet. As a final tie breaker, OSPFv2 chooses the highest router IDs as the DR and BDR.
All other routers establish adjacency with the DR and the BDR and use the IPv4 multicast address 224.0.0.6 to send LSA updates to the DR and BDR. Figure 1-1 shows this adjacency relationship between all routers and the DR.
DRs are based on a router interface. A router might be the DR for one network and not for another network on a different interface.
Figure 1-1 DR in Multi-Access Network
Areas
You can limit the
CPU and memory requirements that OSPFv2 puts on the routers by dividing an OSPFv2 network into
area
s. An area is a logical division of routers and links within an OSPFv2 domain that creates separate subdomains. LSA flooding is contained within an area, and the link-state database is limited to links within the area. You can assign an area ID to the interfaces within the defined area. The Area ID is a 32-bit value that you can enter as a number or in dotted decimal notation, such as 10.2.3.1.
Cisco NX-OS always displays the area in dotted decimal notation.
If you define more than one area in an OSPFv2 network, you must also define the backbone area, which has the reserved area ID of 0. If you have more than one area, then one or more routers become
area border router
s (ABRs). An ABR connects to both the backbone area and at least one other defined area (see
Figure 1-2).
Figure 1-2 OSPFv2 Areas
The ABR has a separate link-state database for each area to which it connects. The ABR sends Network Summary (type 3) LSAs (see the “Route Summarization” section) from one connected area to the backbone area. The backbone area sends summarized information about one area to another area. In Figure 1-2, Area 0 sends summarized information about Area 5 to Area 3.
OSPFv2 defines one other router type: the autonomous system boundary router (ASBR). This router connects an OSPFv2 area to another autonomous system. An autonomous system is a network controlled by a single technical administration entity. OSPFv2 can redistribute its routing information into another autonomous system or receive redistributed routes from another autonomous system. For more information, see “Advanced Features” section.)
Link-State Advertisements
OSPFv2 uses link-state advertisements (LSAs) to build its routing table.
This section includes the following topics:
LSA Types
Table 1-1 shows the LSA types supported by Cisco NX-OS.
Table 1-1 LSA Types
|
|
|
1 |
Router LSA |
LSA sent by every router. This LSA includes the state and the cost of all links and a list of all OSPFv2 neighbors on the link. Router LSAs trigger an SPF recalculation. Router LSAs are flooded to local OSPFv2 area. |
2 |
Network LSA |
LSA sent by the DR. This LSA lists all routers in the multi-access network. Network LSAs trigger an SPF recalculation. See the “Designated Routers” section. |
3 |
Network Summary LSA |
LSA sent by the area border router to an external area for each destination in the local area. This LSA includes the link cost from the area border router to the local destination. See the “Areas” section. |
4 |
ASBR Summary LSA |
LSA sent by the area border router to an external area. This LSA advertises the link cost to the ASBR only. See the “Areas” section. |
5 |
AS External LSA |
LSA generated by the ASBR. This LSA includes the link cost to an external autonomous system destination. AS External LSAs are flooded throughout the autonomous system. See the “Areas” section. |
7 |
NSSA External LSA |
LSA generated by the ASBR within a not-so-stubby area (NSSA). This LSA includes the link cost to an external autonomous system destination. NSSA External LSAs are flooded only within the local NSSA. See the “Areas” section. |
9–11 |
Opaque LSAs |
LSA used to extend OSPF. See the “Opaque LSAs” section. |
Link Cost
Each OSPFv2 interface is assigned a link cost. The cost is an arbitrary number. By default, Cisco NX-OS assigns a cost that is the configured reference bandwidth divided by the interface bandwidth. By default, the reference bandwidth is 40 Gb/s. The link cost is carried in the LSA updates for each link.
Flooding and LSA Group Pacing
When an OSPFv2 router receives an LSA, it forwards that LSA out every OSPF-enabled interface, flooding the OSPFv2 area with this information. This LSA flooding guarantees that all routers in the network have identical routing information. LSA flooding depends on the OSPFv2 area configuration (see the “Areas” section). The LSAs are flooded based on the link-state refresh time (every 30 minutes by default). Each LSA has its own link-state refresh time.
You can control the flooding rate of LSA updates in your network by using the LSA group pacing feature. LSA group pacing can reduce high CPU or buffer utilization. This feature groups LSAs with similar link-state refresh times to allow OSPFv2 to pack multiple LSAs into an OSPFv2 Update message.
By default, LSAs with link-state refresh times within four minutes of each other are grouped together. You should lower this value for large link-state databases or raise it for smaller databases to optimize the OSPFv2 load on your network.
Link-State Database
Each router maintains a link-state database for the OSPFv2 network. This database contains all the collected LSAs, and includes information on all the routes through the network. OSPFv2 uses this information to calculate the bast path to each destination and populates the routing table with these best paths.
LSAs are removed from the link-state database if no LSA update has been received within a set interval, called the MaxAge. Routers flood a repeat of the LSA every 30 minutes to prevent accurate link-state information from being aged out. Cisco NX-OS supports the LSA grouping feature to prevent all LSAs from refreshing at the same time. For more information, see the “Flooding and LSA Group Pacing” section.
Opaque LSAs
Opaque LSAs allow you to extend OSPF functionality. Opaque LSAs consist of a standard LSA header followed by application-specific information. This information might be used by OSPFv2 or by other applications. Three Opaque LSA types are defined as follows:
- LSA type 9—Flooded to the local network.
- LSA type 10—Flooded to the local area.
- LSA type 11—Flooded to the local autonomous system.
OSPFv2 and the Unicast RIB
OSPFv2 runs the Dijkstra shortest path first algorithm on the link-state database. This algorithm selects the best path to each destination based on the sum of all the link costs for each link in the path. The resultant shortest path for each destination is then put in the OSPFv2 route table. When the OSPFv2 network is converged, this route table feeds into the unicast RIB. OSPFv2 communicates with the unicast RIB to do the following:
- Add or remove routes
- Handle route redistribution from other protocols
- Provide convergence updates to remove stale OSPFv2 routes and for stub router advertisements (see the “OSPFv2 Stub Router Advertisements” section)
OSPFv2 also runs a modified Dijkstra algorithm for fast recalculation for summary and external (type 3, 4, 5, and 7) LSA changes.
Authentication
You can configure authentication on OSPFv2 messages to prevent unauthorized or invalid routing updates in your network. Cisco NX-OS supports two authentication methods:
- Simple password authentication
- MD5 authentication digest
You can configure the OSPFv2 authentication for an OSPFv2 area or per interface.
Simple Password Authentication
Simple password authentication uses a simple clear-text password that is sent as part of the OSPFv2 message. The receiving OSPFv2 router must be configured with the same clear-text password to accept the OSPFv2 message as a valid route update. Because the password is in clear text, anyone who can watch traffic on the network can learn the password.
MD5 Authentication
You should use MD5 authentication to authenticate OSPFv2 messages. You configure a password that is shared at the local router and all remote OSPFv2 neighbors. For each OSPFv2 message, Cisco NX-OS creates an MD5 one-way message digest based on the message itself and the encrypted password. The interface sends this digest with the OSPFv2 message. The receiving OSPFv2 neighbor validates the digest using the same encrypted password. If the message has not changed, the digest calculation is identical and the OSPFv2 message is considered valid.
MD5 authentication includes a sequence number with each OSPFv2 message to ensure that no message is replayed in the network.
Advanced Features
Cisco NX-OS supports a number of advanced OSPFv2 features that enhance the usability and scalability of OSPFv2 in the network. This section includes the following topics:
Stub Area
You can limit the amount of external routing information that floods an area by making it a stub area. A stub area is an area that does not allow AS External (type 5) LSAs (see the “Link-State Advertisements” section). These LSAs are usually flooded throughout the local autonomous system to propagate external route information. Stub areas have the following requirements:
- All routers in the stub area are stub routers. See the “Stub Routing” section.
- No ASBR routers exist in the stub area.
- You cannot configure virtual links in the stub area.
Figure 1-3 shows an example of an OSPFv2 autonomous system where all routers in area 0.0.0.10 have to go through the ABR to reach external autonomous systems. area 0.0.0.10 can be configured as a stub area.
Figure 1-3 Stub Area
Stub areas use a default route for all traffic that needs to go through the backbone area to the external autonomous system. The default route is 0.0.0.0 for IPv4.
Not-So-Stubby Area
A Not-so-Stubby Area ( NSSA) is similar to a stub area, except that an NSSA allows you to import autonomous system external routes within an NSSA using redistribution. The NSSA ASBR redistributes these routes and generates NSSA External (type 7) LSAs that it floods throughout the NSSA. You can optionally configure the ABR that connects the NSSA to other areas to translate this NSSA External LSA to AS External (type 5) LSAs. The ABR then floods these AS External LSAs throughout the OSPFv2 autonomous system. Summarization and filtering are supported during the translation. See the “Link-State Advertisements” section for details on NSSA External LSAs.
You can, for example, use NSSA to simplify administration if you are connecting a central site using OSPFv2 to a remote site that is using a different routing protocol. Before NSSA, the connection between the corporate site border router and a remote router could not be run as an OSPFv2 stub area because routes for the remote site could not be redistributed into a stub area. With NSSA, you can extend OSPFv2 to cover the remote connection by defining the area between the corporate router and remote router as an NSSA (see the “Configuring NSSA” section).
The backbone Area 0 cannot be an NSSA.
Virtual Links
Virtual links allow you to connect an OSPFv2 area ABR to a backbone area ABR when a direct physical connection is not available. Figure 1-4 shows a virtual link that connects Area 3 to the backbone area through Area 5.
Figure 1-4 Virtual Links
You can also use virtual links to temporarily recover from a partitioned area, which occurs when a link within the area fails, isolating part of the area from reaching the designated ABR to the backbone area.
Route Redistribution
OSPFv2 can learn routes from other routing protocols by using route redistribution. See the “Route Redistribution” section. You configure OSPFv2 to assign a link cost for these redistributed routes or a default link cost for all redistributed routes.
Route redistribution uses route maps to control which external routes are redistributed. See “Configuring Route Policy Manager,” for details on configuring route maps. You can use route maps to modify parameters in the AS External (type 5) and NSSA External (type 7) LSAs before these external routes are advertised in the local OSPFv2 autonomous system.
Route Summarization
Because OSPFv2 shares all learned routes with every OSPF-enabled router, you might want to use route summarization to reduce the number of unique routes that are flooded to every OSPF-enabled router. Route summarization simplifies route tables by replacing more-specific addresses with an address that represents all the specific addresses. For example, you can replace 10.1.1.0/24, 10.1.2.0/24, and 10.1.3.0/24 with one summary address, 10.1.0.0/16.
Typically, you would summarize at the boundaries of area border routers (ABRs). Although you could configure summarization between any two areas, it is better to summarize in the direction of the backbone so that the backbone receives all the aggregate addresses and injects them, already summarized, into other areas. The two types of summarization are as follows:
- Inter-area route summarization
- External route summarization
You configure inter-area route summarization on ABRs, summarizing routes between areas in the autonomous system. To take advantage of summarization, you should assign network numbers in areas in a contiguous way to be able to lump these addresses into one range.
External route summarization is specific to external routes that are injected into OSPFv2 using route redistribution. You should make sure that external ranges that are being summarized are contiguous. Summarizing overlapping ranges from two different routers could cause packets to be sent to the wrong destination. Configure external route summarization on ASBRs that are redistributing routes into OSPF.
When you configure a summary address, Cisco NX-OS automatically configures a discard route for the summary address to prevent routing black holes and route loops.
OSPFv2 Stub Router Advertisements
You can configure an OSPFv2 interface to act as a stub router using the OSPFv2 Stub Router Advertisements feature. Use this feature when you want to limit the OSPFv2 traffic through this router, such as when you want to introduce a new router to the network in a controlled manner or limit the load on a router that is already overloaded. You might also want to use this feature for various administrative or traffic engineering reasons.
OSPFv2 stub router advertisements do not remove the OSPFv2 router from the network topology, but they do prevent other OSPFv2 routers from using this router to route traffic to other parts of the network. Only the traffic that is destined for this router or directly connected to this router is sent.
OSPFv2 stub router advertisements mark all stub links (directly connected to the local router) to the cost of the local OSPFv2 interface. All remote links are marked with the maximum cost (0xFFFF).
Multiple OSPFv2 Instances
Cisco NX-OS supports multiple instances of the OSPFv2 protocol that run on the same node. You cannot configure multiple instances over the same interface. By default, every instance uses the same system router ID. You must manually configure the router ID for each instance if the instances are in the same OSPFv2 autonomous system.
SPF Optimization
Cisco NX-OS optimizes the SPF algorithm in the following ways:
- Partial SPF for Network (type 2) LSAs, Network Summary (type 3) LSAs, and AS External (type 5) LSAs—When there is a change on any of these LSAs, Cisco NX-OS performs a faster partial calculation rather than running the whole SPF calculation.
- SPF timers—You can configure different timers for controlling SPF calculations. These timers include exponential backoff for subsequent SPF calculations. The exponential backoff limits the CPU load of multiple SPF calculations.
Virtualization Support
OSPFv2 supports Virtual Routing and Forwarding instances (VRFs). By default, Cisco NX-OS places you in the default VRF unless you specifically configure another VRF. Each OSPFv2 instance can support multiple VRFs, up to the system limit. For more information, see Chapter1, “Configuring Layer 3 Virtualization”
Configuring Basic OSPFv2
Configure OSPFv2 after you have designed your OSPFv2 network.
This section includes the following topics:
Enabling the OSPFv2 Feature
You must enable the OSPFv2 feature before you can configure OSPFv2.
SUMMARY STEPS
1.
configure terminal
2.
feature ospf
3.
(Optional) show feature
4.
(Optional) copy running-config startup-config
DETAILED STEPS
|
|
|
Step 1 |
configure terminal Example: switch# configure terminal switch(config)# |
Enters configuration mode. |
Step 2 |
feature ospf Example: switch(config)# feature ospf |
Enables the OSPFv2 feature. |
Step 3 |
show feature Example: switch(config)# show feature |
(Optional) Displays enabled and disabled features. |
Step 4 |
copy running-config startup-config Example: switch(config)# copy running-config startup-config |
(Optional) Saves this configuration change. |
Use the no feature ospf command to disable the OSPFv2 feature and remove all associated configuration.
|
|
no feature ospf Example: switch(config)# no feature ospf |
Disables the OSPFv2 feature and removes all associated configuration. |
Creating an OSPFv2 Instance
The first step in configuring OSPFv2 is to create an OSPFv2 instance. You assign a unique instance tag for this OSPFv2 instance. The instance tag can be any string.
For more information about OSPFv2 instance parameters, see the “Configuring Advanced OSPFv2” section.
BEFORE YOU BEGIN
Ensure that you have enabled the OSPF feature (see the “Enabling the OSPFv2 Feature” section).
Use the show ip ospf instance-tag command to verify that the instance tag is not in use.
OSPFv2 must be able to obtain a router identifier (for example, a configured loopback address) or you must configure the router ID option.
SUMMARY STEPS
1.
configure terminal
2.
router ospf instance-tag
3.
(Optional) router-id ip-address
4.
(Optional) show ip ospf instance-tag
5.
(Optional) copy running-config startup-config
DETAILED STEPS
|
|
|
Step 1 |
configure terminal Example: switch# configure terminal switch(config)# |
Enters configuration mode. |
Step 2 |
router ospf instance-tag Example: switch(config)# router ospf 201 switch(config-router)# |
Creates a new OSPFv2 instance with the configured instance tag. |
Step 3 |
router-id ip-address Example: switch(config-router)# router-id 192.0.2.1 |
(Optional) Configures the OSPFv2 router ID. This IP address identifies this OSPFv2 instance and must exist on a configured interface in the system. |
Step 4 |
show ip ospf instance-tag Example : switch(config-router)# show ip ospf 201 |
(Optional) Displays OSPF information. |
Step 5 |
copy running-config startup-config Example: switch(config)# copy running-config startup-config |
(Optional) Saves this configuration change. |
Use the no router ospf command to remove the OSPFv2 instance and all associated configuration.
|
|
no router ospf instance-tag Example: switch(config)# no router ospf 201 |
Deletes the OSPF instance and the associated configuration. |
Note
This command does not remove OSPF configuration in interface mode. You must manually remove any OSPFv2 commands configured in interface mode.
Configuring Optional Parameters on an OSPFv2 Instance
You can configure optional parameters for OSPF.
For more information about OSPFv2 instance parameters, see the “Configuring Advanced OSPFv2” section.
BEFORE YOU BEGIN
Ensure that you have enabled the OSPF feature (see the “Enabling the OSPFv2 Feature” section).
OSPFv2 must be able to obtain a router identifier (for example, a configured loopback address) or you must configure the router ID option.
DETAILED STEPS
You can configure the following optional parameters for OSPFv2 in router configuration mode:
|
|
distance number Example: switch(config-router)# distance 25 |
Configures the administrative distance for this OSPFv2 instance. The range is from 1 to 255. The default is 110. |
log-adjacency-changes [ detail ] Example: switch(config-router)# log-adjacency-changes |
Generates a system message whenever a neighbor changes state. |
maximum-paths path-number Example: switch(config-router)# maximum-paths 4 |
Configures the maximum number of equal OSPFv2 paths to a destination in the route table. This command is used for load balancing. The range is from 1 to 16. The default is 8. |
This example shows how to create an OSPFv2 instance:
switch# configure terminal
switch(config)# router ospf 201
switch(config-router)# copy running-config startup-config
Configuring Networks in OSPFv2
You can configure a network to OSPFv2 by associating it through the interface that the router uses to connect to that network (see the “Neighbors” section). You can add all networks to the default backbone area (Area 0), or you can create new areas using any decimal number or an IP address.
Note
All areas must connect to the backbone area either directly or through a virtual link.
Note
OSPF is not enabled on an interface until you configure a valid IP address for that interface.
SUMMARY STEPS
1.
configure terminal
2.
interface interface-type slot/port
3.
no switchport
4.
ip address ip-prefix/length
5.
ip router ospf instance-tag area area-id [ secondaries none ]
6.
(Optional) show ip ospf instance-tag interface interface-type slot/por t
7.
(Optional) copy running-config startup-config
DETAILED STEPS
|
|
|
Step 1 |
configure terminal Example: switch# configure terminal switch(config)# |
Enters configuration mode. |
Step 2 |
interface interface-type slot/port Example: switch(config)# interface ethernet 1/2 switch(config-if)# |
Enters interface configuration mode. |
Step 3 |
no switchport Example: switch(config-if)# no switchport |
Configures the interface as a Layer 3 routed interface. |
Step 4 |
ip address ip-prefix/length Example: switch(config-if)# ip address 192.0.2.1/16 |
Assigns an IP address and subnet mask to this interface. |
Step 5 |
ip router ospf instance-tag area area-id [ secondaries none ] Example: switch(config-if)# ip router ospf 201 area 0.0.0.15 |
Adds the interface to the OSPFv2 instance and area. |
Step 6 |
show ip ospf instance-tag interface interface-type slot/port Example : switch(config-if)# show ip ospf 201 interface ethernet 1/2 |
(Optional) Displays OSPF information. |
Step 7 |
copy running-config startup-config Example: switch(config)# copy running-config startup-config |
(Optional) Saves this configuration change. |
You can configure the following optional parameters for OSPFv2 in interface configuration mode:
|
|
ip ospf cost number Example: switch(config-if)# ip ospf cost 25 |
Configures the OSPFv2 cost metric for this interface. The default is to calculate cost metric, based on reference bandwidth and interface bandwidth. The range is from 1 to 65535. |
ip ospf dead-interval seconds Example: switch(config-if)# ip ospf dead-interval 50 |
Configures the OSPFv2 dead interval, in seconds. The range is from 1 to 65535. The default is four times the hello interval, in seconds. |
ip ospf hello-interval seconds Example: switch(config-if)# ip ospf hello-interval 25 |
Configures the OSPFv2 hello interval, in seconds. The range is from 1 to 65535. The default is 10 seconds. |
ip ospf mtu-ignore Example: switch(config-if)# ip ospf mtu-ignore |
Configures OSPFv2 to ignore any IP MTU mismatch with a neighbor. The default is to not establish adjacency if the neighbor MTU does not match the local interface MTU. |
ip ospf passive-interface Example: switch(config-if)# ip ospf passive-interface |
Suppresses routing updates on the interface. |
ip ospf priority number Example: switch(config-if)# ip ospf priority 25 |
Configures the OSPFv2 priority, used to determine the DR for an area. The range is from 0 to 255. The default is 1. See the “Designated Routers” section. |
ip ospf shutdown Example: switch(config-if)# ip ospf shutdown |
Shuts down the OSPFv2 instance on this interface. |
This example shows how to add a network area 0.0.0.10 in OSPFv2 instance 201:
switch# configure terminal
switch(config)# interface ethernet 1/2
switch(config-if)# no switchport
switch(config-if)# ip address 192.0.2.1/16
switch(config-if)# ip router ospf 201 area 0.0.0.10
switch(config-if)# copy running-config startup-config
Use the show ip ospf interface command to verify the interface configuration. Use the show ip ospf neighbor command to see the neighbors for this interface.
Configuring Authentication for an Area
You can configure authentication for all networks in an area or for individual interfaces in the area. Interface authentication configuration overrides area authentication.
BEFORE YOU BEGIN
Ensure that you have enabled the OSPF feature (see the “Enabling the OSPFv2 Feature” section).
Ensure that all neighbors on an interface share the same authentication configuration, including the shared authentication key.
Create the key-chain for this authentication configuration. See the Cisco Nexus 5000 Series NX-OS Security Configuration Guide, Release 5.0(3)N1(1).
SUMMARY STEPS
1.
configure terminal
2.
router ospf instance-tag
3.
area area-id authentication [ message-digest ]
4.
interface interface-type slot/port
5.
no switchport
6.
(Optional) ip ospf authentication-key [ 0 | 3 ] key
or
(Optional) ip ospf message-digest-key key-id md5 [ 0 | 3 ] key
7.
(Optional) show ip ospf instance-tag interface interface-type slot/por t
8.
(Optional) copy running-config startup-config
DETAILED STEPS
|
|
|
Step 1 |
configure terminal Example: switch# configure terminal switch(config)# |
Enters configuration mode. |
Step 2 |
router ospf instance-tag Example: switch(config)# router ospf 201 switch(config-router)# |
Creates a new OSPFv2 instance with the configured instance tag. |
Step 3 |
area area-id authentication [ message-digest ] Example: switch(config-router)# area 0.0.0.10 authentication |
Configures the authentication mode for an area. |
Step 4 |
interface interface-type slot/port Example: switch(config-router)# interface ethernet 1/2 switch(config-if)# |
Enters interface configuration mode. |
Step 5 |
no switchport Example: switch(config-if)# no switchport |
Configures the interface as a Layer 3 routed interface. |
Step 6 |
ip ospf authentication-key [ 0 | 3 ] key Example: switch(config-if)# ip ospf authentication-key 0 mypass |
(Optional) Configures simple password authentication for this interface. Use this command if the authentication is not set to key-chain or message-digest. 0 configures the password in clear text. 3 configures the password as 3DES encrypted. |
ip ospf message-digest-key key-id md5 [ 0 | 3 ] key Example: switch(config-if)# ip ospf message-digest-key 21 md5 0 mypass |
(Optional) Configures message digest authentication for this interface. Use this command if the authentication is set to message-digest. The key-id range is from 1 to 255. The MD5 option 0 configures the password in clear text and 3 configures the pass key as 3DES encrypted. |
Step 7 |
show ip ospf instance-tag interface interface-type slot/port Example : switch(config-if)# show ip ospf 201 interface ethernet 1/2 |
(Optional) Displays OSPF information. |
Step 8 |
copy running-config startup-config Example: switch(config)# copy running-config startup-config |
(Optional) Saves this configuration change. |
Configuring Authentication for an Interface
You can configure authentication for individual interfaces in the area. Interface authentication configuration overrides area authentication.
BEFORE YOU BEGIN
Ensure that you have enabled the OSPF feature (see the “Enabling the OSPFv2 Feature” section).
Ensure that all neighbors on an interface share the same authentication configuration, including the shared authentication key.
Create the key-chain for this authentication configuration. See the Cisco Nexus 5000 Series NX-OS Security Configuration Guide, Release 5.0(3)N1(1).
SUMMARY STEPS
1.
configure terminal
2.
interface interface-type slot/port
3.
no switchport
4.
ip ospf authentication [ message-diges t]
5.
(Optional) ip ospf authentication key-chain key-id
6.
(Optional) ip ospf authentication-key [ 0 | 3 ] key
7.
(Optional) ip ospf message-digest-key key-id md5 [ 0 | 3 ] key
8.
(Optional) show ip ospf instance-tag interface interface-type slot/por t
9.
(Optional) copy running-config startup-config
DETAILED STEPS
|
|
|
Step 1 |
configure terminal Example: switch# configure terminal switch(config)# |
Enters configuration mode. |
Step 2 |
interface interface-type slot/port Example: switch(config)# interface ethernet 1/2 switch(config-if)# |
Enters interface configuration mode. |
Step 3 |
no switchport Example: switch(config-if)# no switchport |
Configures the interface as a Layer 3 routed interface. |
Step 4 |
ip ospf authentication [ message-digest ] Example: switch(config-if)# ip ospf authentication |
Enables interface authentication mode for OSPFv2 for either cleartext or message-digest type. Overrides area-based authentication for this interface. All neighbors must share this authentication type. |
Step 5 |
ip ospf authentication key-chain key-name Example: switch(config-if)# ip ospf authentication key-chain Test1 |
(Optional) Configures interface authentication to use key chains for OSPFv2. See the Cisco Nexus 5000 Series NX-OS Security Configuration Guide, Release 5.0(3)N1(1), for details on key chains. |
Step 6 |
ip ospf authentication-key [ 0 | 3 | 7 ] key Example: switch(config-if)# ip ospf authentication-key 0 mypass |
(Optional) Configures simple password authentication for this interface. Use this command if the authentication is not set to key-chain or message-digest. The options are as follows:
- 0—configures the password in clear text.
- 3—configures the pass key as 3DES encrypted.
- 7—configures the key as Cisco type 7 encrypted.
|
Step 7 |
ip ospf message-digest-key key-id md5 [ 0 | 3 | 7 ] key Example: switch(config-if)# ip ospf message-digest-key 21 md5 0 mypass |
(Optional) Configures message digest authentication for this interface. Use this command if the authentication is set to message-digest.The key-id range is from 1 to 255. The MD5 options are as follows:
- 0—configures the password in clear text.
- 3—configures the pass key as 3DES encrypted.
- 7—configures the key as Cisco type 7 encrypted.
|
Step 8 |
show ip ospf instance-tag interface interface-type slot/port Example : switch(config-if)# show ip ospf 201 interface ethernet 1/2 |
(Optional) Displays OSPF information. |
Step 9 |
copy running-config startup-config Example: switch(config)# copy running-config startup-config |
(Optional) Saves this configuration change. |
This example shows how to set an interface for simple, unencrypted passwords and set the password for Ethernet interface 1/2:
switch# configure terminal
switch(config)# router ospf 201
switch(config-router)# exit
switch(config)# interface ethernet 1/2
switch(config-if)# no switchport
switch(config-if)# ip router ospf 201 area 0.0.0.10
switch(config-if)# ip ospf authentication
switch(config-if)# ip ospf authentication-key 0 mypass
switch(config-if)# copy running-config startup-config
Configuring Advanced OSPFv2
Configure OSPFv2 after you have designed your OSPFv2 network.
This section includes the following topics:
Configuring Filter Lists for Border Routers
You can separate your OSPFv2 domain into a series of areas that contain related networks. All areas must connect to the backbone area through an area border router (ABR). OSPFv2 domains can connect to external domains as well, through an autonomous system border router (ASBR). See the “Areas” section.
ABRs have the following optional configuration parameters:
- Area range—Configures route summarization between areas.
- Filter list—Filters the Network Summary (type 3) LSAs on an ABR that are allowed in from an external area.
ASBRs also support filter lists.
SUMMARY STEPS
1.
configure terminal
2.
router ospf instance-tag
3.
area area-id filter-list route-map map-name { in | out }
4.
(Optional) show ip ospf policy statistics
5.
(Optional) copy running-config startup-config
DETAILED STEPS
|
|
|
Step 1 |
configure terminal Example: switch# configure terminal switch(config)# |
Enters configuration mode. |
Step 2 |
router ospf instance-tag Example: switch(config)# router ospf 201 switch(config-router)# |
Creates a new OSPFv2 instance with the configured instance tag. |
Step 3 |
area area-id filter-list route-map map-name { in | out } Example: switch(config-router)# area 0.0.0.10 filter-list route-map FilterLSAs in |
Filters incoming or outgoing Network Summary (type 3) LSAs on an ABR. |
Step 4 |
show ip ospf policy statistics area id filter-list { in | out } Example : switch(config-if)# show ip ospf policy statistics area 0.0.0.10 filter-list in |
(Optional) Displays OSPF policy information. |
Step 5 |
copy running-config startup-config Example: switch(config)# copy running-config startup-config |
(Optional) Saves this configuration change. |
This example shows how to configure a filter list in area 0.0.0.10:
switch# configure terminal
switch(config)# router ospf 201
switch(config-router)# area 0.0.0.10 filter-list route-map FilterLSAs in
switch(config-router)# copy running-config startup-config
Configuring Stub Areas
You can configure a stub area for part of an OSPFv2 domain where external traffic is not necessary. Stub areas block AS External (type 5) LSAs, limiting unnecessary routing to and from selected networks. See the “Stub Area” section. You can optionally block all summary routes from going into the stub area.
BEFORE YOU BEGIN
Ensure that you have enabled the OSPF feature (see the “Enabling the OSPFv2 Feature” section).
Ensure that there are no virtual links or ASBRs in the proposed stub area.
SUMMARY STEPS
1.
configure terminal
2.
router ospf instance-tag
3.
area area-id stub
4.
(Optional) area area-id default-cost cost
5.
(Optional) show ip ospf instance-tag
6.
(Optional) copy running-config startup-config
|
|
|
Step 1 |
configure terminal Example: switch# configure terminal switch(config)# |
Enters configuration mode. |
Step 2 |
router ospf instance-tag Example: switch(config)# router ospf 201 switch(config-router)# |
Creates a new OSPFv2 instance with the configured instance tag. |
Step 3 |
area area-id stub Example: switch(config-router)# area 0.0.0.10 stub |
Creates this area as a stub area. |
Step 4 |
area area-id default-cost cost Example: switch(config-router)# area 0.0.0.10 default-cost 25 |
(Optional) Sets the cost metric for the default summary route sent into this stub area. The range is from 0 to 16777215. The default is 1. |
Step 5 |
show ip ospf instance-tag Example : switch(config-if)# show ip ospf 201 |
(Optional) Displays OSPF information. |
Step 6 |
copy running-config startup-config Example: switch(config)# copy running-config startup-config |
(Optional) Saves this configuration change. |
This example shows how to create a stub area:
switch# configure terminal
switch(config)# router ospf 201
switch(config-router)# area 0.0.0.10 stub
switch(config-router)# copy running-config startup-config
Configuring a Totally Stubby Area
You can create a totally stubby area and prevent all summary route updates from going into the stub area.
To create a totally stubby area, use the following command in router configuration mode:
|
|
area area-id stub no-summary Example: switch(config-router)# area 20 stub no-summary |
Creates this area as a totally stubby area. |
Configuring NSSA
You can configure an NSSA for part of an OSPFv2 domain where limited external traffic is required. See the “Not-So-Stubby Area” section. You can optionally translate this external traffic to an AS External (type 5) LSA and flood the OSPFv2 domain with this routing information. An NSSA can be configured with the following optional parameters:
- No redistribution— Redistributed routes bypass the NSSA and are redistributed to other areas in the OSPFv2 autonomous system. Use this option when the NSSA ASBR is also an ABR.
- Default information originate—Generates an NSSA External (type 7) LSA for a default route to the external autonomous system. Use this option on an NSSA ASBR if the ASBR contains the default route in the routing table. This option can be used on an NSSA ABR whether or not the ABR contains the default route in the routing table.
- Route map—Filters the external routes so that only those routes that you want are flooded throughout the NSSA and other areas.
- Translate—Translates NSSA External LSAs to AS External LSAs for areas outside the NSSA. Use this command on an NSSA ABR to flood the redistributed routes throughout the OSPFv2 autonomous system. You can optionally suppress the forwarding address in these AS External LSAs. If you choose this option, the forwarding address is set to 0.0.0.0.
- No summary—Blocks all summary routes from flooding the NSSA. Use this option on the NSSA ABR.
BEFORE YOU BEGIN
Ensure that you have enabled the OSPF feature (see the “Enabling the OSPFv2 Feature” section).
Ensure that there are no virtual links in the proposed NSSA and that it is not the backbone area.
SUMMARY STEPS
1.
configure terminal
2.
router ospf instance-tag
3.
area area-id nssa [ no-redistribution ] [ default-information-originate [ route-map map-name ]] [ no-summary ] [ translate type7 { always | never } [ suppress-fa ]]
4.
(Optional) area area-id default-cost cost
5.
(Optional) show ip ospf instance-tag
6.
(Optional) copy running-config startup-config
DETAILED STEPS
|
|
|
Step 1 |
configure terminal Example: switch# configure terminal switch(config)# |
Enters configuration mode. |
Step 2 |
router ospf instance-tag Example: switch(config)# router ospf 201 switch(config-router)# |
Creates a new OSPFv2 instance with the configured instance tag. |
Step 3 |
area area-id nssa [ no-redistribution ] [ default-information-originate ] [ route-map map-name ]] [ no-summary ] [ translate type7 { always | never } [ suppress-fa ]] Example: switch(config-router)# area 0.0.0.10 nssa |
Creates this area as an NSSA. |
Step 4 |
area area-id default-cost cost Example: switch(config-router)# area 0.0.0.10 default-cost 25 |
(Optional) Sets the cost metric for the default summary route sent into this NSSA. |
Step 5 |
show ip ospf instance-tag Example : switch(config-if)# show ip ospf 201 |
(Optional) Displays OSPF information. |
Step 6 |
copy running-config startup-config Example: switch(config)# copy running-config startup-config |
(Optional) Saves this configuration change. |
This example shows how to create an NSSA that blocks all summary route updates:
switch# configure terminal
switch(config)# router ospf 201
switch(config-router)# area 0.0.0.10 nssa no-summary
switch(config-router)# copy running-config startup-config
This example shows how to create an NSSA that generates a default route:
switch# configure terminal
switch(config)# router ospf 201
switch(config-router)# area 0.0.0.10 nssa default-info-originate
switch(config-router)# copy running-config startup-config
This example shows how to create an NSSA that filters external routes and blocks all summary route updates:
switch# configure terminal
switch(config)# router ospf 201
switch(config-router)# area 0.0.0.10 nssa route-map ExternalFilter no-summary
switch(config-router)# copy running-config startup-config
This example shows how to create an NSSA that always translates NSSA External (type 5) LSAs to AS External (type 7) LSAs:
switch# configure terminal
switch(config)# router ospf 201
switch(config-router)# area 0.0.0.10 nssa translate type 7 always
switch(config-router)# copy running-config startup-config
Configuring Virtual Links
A virtual link connects an isolated area to the backbone area through an intermediate area. See the “Virtual Links” section. You can configure the following optional parameters for a virtual link:
- Authentication—Sets a simple password or MD5 message digest authentication and associated keys.
- Dead interval—Sets the time that a neighbor waits for a Hello packet before declaring the local router as dead and tearing down adjacencies.
- Hello interval—Sets the time between successive Hello packets.
- Retransmit interval—Sets the estimated time between successive LSAs.
- Transmit delay—Sets the estimated time to transmit an LSA to a neighbor.
Note
You must configure the virtual link on both routers involved before the link becomes active.
You cannot add a virtual link to a stub area.
SUMMARY STEPS
1.
configure terminal
2.
router ospf instance-tag
3.
area area-id virtual-link router-id
4.
(Optional) show ip ospf virtual-link [ brief ]
5.
(Optional) copy running-config startup-config
DETAILED STEPS
|
|
|
Step 1 |
configure terminal Example: switch# configure terminal switch(config)# |
Enters configuration mode. |
Step 2 |
router ospf instance-tag Example: switch(config)# router ospf 201 switch(config-router)# |
Creates a new OSPFv2 instance with the configured instance tag. |
Step 3 |
area area-id virtual-link router-id Example: switch(config-router)# area 0.0.0.10 virtual-link 10.1.2.3 switch(config-router-vlink)# |
Creates one end of a virtual link to a remote router. You must create the virtual link on that remote router to complete the link. |
Step 4 |
show ip ospf virtual-link [ brief ] Example : switch(config-router-vlink)# show ip ospf virtual-link |
(Optional) Displays OSPF virtual link information. |
Step 5 |
copy running-config startup-config Example: switch(config-router-vlink)# copy running-config startup-config |
(Optional) Saves this configuration change. |
You can configure the following optional commands in virtual link configuration mode:
|
|
authentication [ key-chain key-id | message-digest | null ] Example: switch(config-router-vlink)# authentication message-digest |
(Optional) Overrides area-based authentication for this virtual link. |
authentication-key [ 0 | 3 ] key Example: switch(config-router-vlink)# authentication-key 0 mypass |
(Optional) Configures a simple password for this virtual link. Use this command if the authentication is not set to key-chain or message-digest. 0 configures the password in clear text. 3 configures the password as 3DES encrypted. |
dead-interval seconds Example : switch(config-router-vlink)# dead-interval 50 |
(Optional) Configures the OSPFv2 dead interval, in seconds. The range is from 1 to 65535. The default is four times the hello interval, in seconds. |
hello-interval seconds Example: switch(config-router-vlink)# hello-interval 25 |
(Optional) Configures the OSPFv2 hello interval, in seconds. The range is from 1 to 65535. The default is 10 seconds. |
message-digest-key key-id md5 [ 0 | 3 ] key Example: switch(config-router-vlink)# message-digest-key 21 md5 0 mypass |
(Optional) Configures message digest authentication for this virtual link. Use this command if the authentication is set to message-digest. 0 configures the password in cleartext. 3 configures the pass key as 3DES encrypted. |
retransmit-interval seconds Example : switch(config-router-vlink)# retransmit-interval 50 |
(Optional) Configures the OSPFv2 retransmit interval, in seconds. The range is from 1 to 65535. The default is 5. |
transmit-delay seconds Example: switch(config-router-vlink)# transmit-delay 2 |
(Optional) Configures the OSPFv2 transmit-delay, in seconds. The range is from 1 to 450. The default is 1. |
This example shows how to create a simple virtual link between two ABRs.
The configuration for ABR 1 (router ID 27.0.0.55) is as follows:
switch# configure terminal
switch(config)# router ospf 201
switch(config-router)# area 0.0.0.10 virtual-link 10.1.2.3
switch(config-router-vlink)# copy running-config startup-config
The configuration for ABR 2 (Router ID 10.1.2.3) is as follows:
switch# configure terminal
switch(config)# router ospf 101
switch(config-router)# area 0.0.0.10 virtual-link 27.0.0.55
switch(config-router-vlink)# copy running-config startup-config
Configuring Redistribution
You can redistribute routes learned from other routing protocols into an OSPFv2 autonomous system through the ASBR.
You can configure the following optional parameters for route redistribution in OSPF:
- Default information originate—Generates an AS External (type 5) LSA for a default route to the external autonomous system.
Note
Default information originate ignores match statements in the optional route map.
- Default metric—Sets all redistributed routes to the same cost metric.
Note
If you redistribute static routes, Cisco NX-OS also redistributes the default static route.
SUMMARY STEPS
1.
configure terminal
2.
router ospf instance-tag
3.
redistribute { bgp id | direct | eigrp id | ospf id | rip id | static } route-map map-name
4.
default-information originate [ always ] [ route-map map-name ]
5.
default-metric cost
6.
(Optional) copy running-config startup-config
DETAILED STEPS
|
|
|
Step 1 |
configure terminal Example: switch# configure terminal switch(config)# |
Enters configuration mode. |
Step 2 |
router ospf instance-tag Example: switch(config)# router ospf 201 switch(config-router)# |
Creates a new OSPFv2 instance with the configured instance tag. |
Step 3 |
redistribute { bgp id | direct | eigrp id | ospf id | rip id | static } route-map map-name Example: switch(config-router)# redistribute bgp 64496 route-map FilterExternalBGP |
Redistributes the selected protocol into OSPF through the configured route map. Note If you redistribute static routes, Cisco NX-OS also redistributes the default static route. |
Step 4 |
default-information originate [ always ] [ route-map map-name] Example: switch(config-router)# default-information-originate route-map DefaultRouteFilter |
Creates a default route into this OSPF domain if the default route exists in the RIB. Use the following optional keywords:
- always —Always generate the default route of 0.0.0. even if the route does not exist in the RIB.
- route-map —Generate the default route if the route map returns true.
Note This command ignores match statements in the route map. |
Step 5 |
default-metric cost Example: switch(config-router)# default-metric 25 |
Sets the cost metric for the redistributed routes. This does not apply to directly connected routes. Use a route map to set the default metric for directly connected routes. |
Step 6 |
copy running-config startup-config Example: switch(config-router)# copy running-config startup-config |
(Optional) Saves this configuration change. |
This example shows how to redistribute the Border Gateway Protocol (BGP) into OSPF:
switch# configure terminal
switch(config)# router ospf 201
switch(config-router)# redistribute bgp route-map FilterExternalBGP
switch(config-router)# copy running-config startup-config
Limiting the Number of Redistributed Routes
Route redistribution can add many routes to the OSPFv2 route table. You can configure a maximum limit to the number of routes accepted from external protocols. OSPFv2 provides the following options to configure redistributed route limits:
- Fixed limit—Log a message when OSPFv2 reaches the maximum the configured maximum. OSPFv2 does not accept any more redistributed routes. You can optionally configure a threshold percentage of the maximum where OSPFv2 will log a warning when that threshold is passed.
- Warning only—Log a warning only when OSPFv2 reaches the maximum. OSPFv2 continuse to accept redistributed routes.
- Widthdraw—Start the timeout period when OSPFv2 reaches the maximum. After the timeout period, OSPFv2 requests all redistributed routes if the current number of redistributed routes is less than the maximum limit. If the current number of redistributed routes is at the maximum limit, OSPFv2 withdraws all redistributed routes. You must clear this condition before OSPFv2 accepts more redistributed routes.
You can optionally configure the timeout period.
SUMMARY STEPS
1.
configure terminal
2.
router ospf instance-tag
3.
redistribute { bgp id | direct| eigrp id | ospf id | rip id | static } route-map map-name
4.
redistribute maximum-prefix max [ threshold ] [ warning-only | withdraw [ num-retries timeout ]]
5.
(Optional) show running-config ospf
6.
(Optional) copy running-config startup-config
DETAILED STEPS
|
|
|
Step 1 |
configure terminal Example: switch# configure terminal switch(config)# |
Enters configuration mode. |
Step 2 |
router ospf instance-tag Example: switch(config)# router ospf 201 switch(config-router)# |
Creates a new OSPFv2 instance with the configured instance tag. |
Step 3 |
redistribute { bgp id | direct | eigrp id | ospf id | rip id | static } route-map map-name Example: switch(config-router)# redistribute bgp route-map FilterExternalBGP |
Redistributes the selected protocol into OSPF through the configured route map. |
Step 4 |
redistribute maximum-prefix max [ threshold ] [ warning-only | withdraw [ num-retries timeout ]] Example: switch(config-router)# redistribute maximum-prefix 1000 75 warning-only |
Specifies a maximum number of prefixes that OSPFv2 will distribute. The range is from 0 to 65536. Optionally specifies the following:
- threshold —Percent of maximum prefixes that will trigger a warning message.
- warning-only —Logs an warning message when the maximum number of prefixes is exceeded.
- withdraw —Withdraws all redistributed routes. Optionally tries to retrieve the redistributed routes. The num-retries range is from 1 to 12. The timeout is 60 to 600 seconds. The default is 300 seconds. Use clear ip ospf redistribution if all routes are withdrawn.
|
Step 5 |
show running-config ospf Example: switch(config-router)# show running-config ospf |
(Optional) Displays the OSPFv2 configuration. |
Step 6 |
copy running-config startup-config Example: switch(config-router)# copy running-config startup-config |
(Optional) Saves this configuration change. |
This example shows how to limit the number of redistributed routes into OSPF:
switch# configure terminal
switch(config)# router ospf 201
switch(config-router)# redistribute bgp route-map FilterExternalBGP
switch(config-router)# redistribute maximum-prefix 1000 75
Configuring Route Summarization
You can configure route summarization for inter-area routes by configuring an address range that is summarized. You can also configure route summarization for external, redistributed routes by configuring a summary address for those routes on an ASBR. See the “Route Summarization” section.
SUMMARY STEPS
1.
configure terminal
2.
router ospf instance-tag
3.
area area-id range ip-prefix/length [ no-advertise ]
4.
summary-address ip-prefix/length [ no-advertise | tag tag-id ]
5.
(Optional) show ip ospf summary-address
6.
(Optional) copy running-config startup-config
DETAILED STEPS
|
|
|
Step 1 |
configure terminal Example: switch# configure terminal switch(config)# |
Enters configuration mode. |
Step 2 |
router ospf instance-tag Example: switch(config)# router ospf 201 switch(config-router)# |
Creates a new OSPFv2 instance with the configured instance tag. |
Step 3 |
area area-id range ip-prefix/length [ no-advertise ] Example: switch(config-router)# area 0.0.0.10 range 10.3.0.0/16 |
Creates a summary address on an ABR for a range of addresses and optionally does note advertise this summary address in a Network Summary (type 3) LSA. |
Step 4 |
summary-address ip-prefix/length [ no-advertise | tag tag] Example: switch(config-router)# summary-address 10.5.0.0/16 tag 2 |
Creates a summary address on an ASBR for a range of addresses and optionally assigns a tag for this summary address that can be used for redistribution with route maps. |
Step 5 |
show ip ospf summary-address Example : switch(config-router)# show ip ospf summary-address |
(Optional) Displays information about OSPF summary addresses. |
Step 6 |
copy running-config startup-config Example: switch(config-router)# copy running-config startup-config |
(Optional) Saves this configuration change. |
This example shows how to create summary addresses between areas on an ABR:
switch# configure terminal
switch(config)# router ospf 201
switch(config-router)# area 0.0.0.10 range 10.3.0.0/16
switch(config-router)# copy running-config startup-config
This example shows how to create summary addresses on an ASBR;
switch# configure terminal
switch(config)# router ospf 201
switch(config-router)# summary-address 10.5.0.0/16
switch(config-router)# copy running-config startup-config
Configuring Stub Route Advertisements
Use Stub Route Advertisements when you want to limit the OSPFv2 traffic through this router for a short time. See the “OSPFv2 Stub Router Advertisements” section.
Stub route advertisements can be configured with the following optional parameters:
- On startup—Sends stub route advertisements for the specified announce time.
- Wait for BGP—Sends stub router advertisements until BGP converges.
SUMMARY STEPS
1.
configure terminal
2.
router ospf instance-tag
3.
max-metric router-lsa [ on-startup [ announce-time ] [ wait-for bgp tag ]]
4.
(Optional) copy running-config startup-config
Note
You should not save the running configuration of a router when it is configured for a graceful shutdown because the router will continue to advertise a maximum metric after it is reloaded.
DETAILED STEPS
|
|
|
Step 1 |
configure terminal Example: switch# configure terminal switch(config)# |
Enters configuration mode. |
Step 2 |
router ospf instance-tag Example: switch(config)# router ospf 201 switch(config-router)# |
Creates a new OSPFv2 instance with the configured instance tag. |
Step 3 |
max-metric router-lsa [ on-startup [ announce-time ] [ wait-for bgp tag ]] Example: switch(config-router)# max-metric router-lsa |
Configures OSPFv2 stub route advertisements. |
Step 4 |
copy running-config startup-config Example: switch(config-router)# copy running-config startup-config |
(Optional) Saves this configuration change. |
This example shows how to enable the Stub Router Advertisements feature on startup for the default 600 seconds:
switch# configure terminal
switch(config)# router ospf 201
switch(config-router)# max-metric router-lsa on-startup
switch(config-router)# copy running-config startup-config
Modifying the Default Timers
OSPFv2 includes a number of timers that control the behavior of protocol messages and shortest path first (SPF) calculations. OSPFv2 includes the following optional timer parameters:
- LSA arrival time—Sets the minimum interval allowed between LSAs arriving from a neighbor. LSAs that arrive faster than this time are dropped.
- Pacing LSAs—Set the interval at which LSAs are collected into a group and refreshed, checksummed, or aged. This timer controls how frequently LSA updates occur and optimizes how many are sent in an LSA update message (see the “Flooding and LSA Group Pacing” section).
- Throttle LSAs—Set rate limits for generating LSAs. This timer controls how frequently an LSA is generated if no topology change occurs.
- Throttle SPF calculation—Controls how frequently the SPF calculation is run.
At the interface level, you can also control the following timers:
- Retransmit interval—Sets the estimated time between successive LSAs.
- Transmit delay—Sets the estimated time to transmit an LSA to a neighbor.
See the “Configuring Networks in OSPFv2” section for information about the hello interval and dead timer.
SUMMARY STEPS
1.
configure terminal
2.
router ospf instance-tag
3.
timers lsa-arrival msec
4.
timers lsa-group-pacing seconds
5.
timers throttle lsa start-time hold-interval max-time
6.
timers throttle spf delay-time hold-time
7.
interface type slot/port
8.
no switchport
9.
ip ospf hello-interval seconds
10.
ip ospf dead-interval seconds
11.
ip ospf retransmit-interval seconds
12.
ip ospf transmit-delay seconds
13.
(Optional) show ip ospf
14.
(Optional) copy running-config startup-config
DETAILED STEPS
|
|
|
Step 1 |
configure terminal Example: switch# configure terminal switch(config)# |
Enters configuration mode. |
Step 2 |
router ospf instance-tag Example: switch(config)# router ospf 201 switch(config-router)# |
Creates a new OSPFv2 instance with the configured instance tag. |
Step 3 |
timers lsa-arrival msec Example: switch(config-router)# timers lsa-arrival 2000 |
Sets the LSA arrival time in milliseconds. The range is from 10 to 600000. The default is 1000 milliseconds. |
Step 4 |
timers lsa-group-pacing seconds Example: switch(config-router)# timers lsa-group-pacing 1800 |
Sets the interval in seconds for grouping LSAs. The range is from 1 to 1800. The default is 240 seconds. |
Step 5 |
timers throttle lsa start-time hold-interval max-time Example: switch(config-router)# timers throttle lsa 3000 6000 6000 |
Sets the rate limit in milliseconds for generating LSAs with the following timers: start-time —The range is from 50 to 5000 milliseconds. The default value is 50 milliseconds. hold-interva l—The range is from 50 to 30,000 milliseconds. The default value is 5000 milliseconds. max-time —The range is from 50 to 30,000 milliseconds. The default value is 5000 milliseconds. |
Step 6 |
timers throttle spf delay-time hold-time max-wait Example: switch(config-router)# timers throttle spf 3000 2000 4000 |
Sets the SPF best path schedule initial delay time and the minimum hold time in seconds between SPF best path calculations. The range is from 1 to 600000. The default is no delay time and 5000 millisecond hold time. |
Step 7 |
interface type slot/port Example : switch(config)# interface ethernet 1/2 switch(config-if)# |
Enters interface configuration mode. |
Step 8 |
no switchport Example: switch(config-if)# no switchport |
Configures the interface as a Layer 3 routed interface. |
Step 9 |
ip ospf hello-interval seconds Example: switch(config-if)# ip ospf retransmit-interval 30 |
Sets the hello interval this interface. The range is from 1 to 65535. The default is 10. |
Step 10 |
ip ospf dead-interval seconds Example: switch(config-if)# ip ospf dead-interval 30 |
Sets the dead interval for this interface. The range is from 1 to 65535. |
Step 11 |
ip ospf retransmit-interval seconds Example: switch(config-if)# ip ospf retransmit-interval 30 |
Sets the estimated time in seconds between LSAs transmitted from this interface. The range is from 1 to 65535. The default is 5. |
Step 12 |
ip ospf transmit-delay seconds Example: switch(config-if)# ip ospf transmit-delay 450 switch(config-if)# |
Sets the estimated time in seconds to transmit an LSA to a neighbor. The range is from 1 to 450. The default is 1. |
Step 13 |
show ip ospf Example : switch(config-if)# show ip ospf |
(Optional) Displays information about OSPF. |
Step 14 |
copy running-config startup-config Example: switch(config-if)# copy running-config startup-config |
(Optional) Saves this configuration change. |
This example shows how to control LSA flooding with the lsa-group-pacing option:
switch# configure terminal
switch(config)# router ospf 201
switch(config-router)# timers lsa-group-pacing 300
switch(config-router)# copy running-config startup-config
Restarting an OSPFv2 Instance
You can restart an OSPv2 instance. This clears all neighbors for the instance.
To restart an OSPFv2 instance and remove all associated neighbors, use the following command:
|
|
restart ospf instance-tag Example: switch(config)# restart ospf 201 |
Restarts the OSPFv2 instance and removes all neighbors. |
Configuring OSPFv2 with Virtualization
You can create multiple VRFs and use the same or multiple OSPFv2 instances in each VRF. You assign an OSPFv2 interface to a VRF.
Note
Configure all other parameters for an interface after you configure the VRF for an interface. Configuring a VRF for an interface deletes all the configuration for that interface.
SUMMARY STEPS
1.
configure terminal
2.
vrf context vrf_name
3.
router ospf instance-tag
4.
vrf vrf-name
5.
maximum-paths paths
6.
interface interface-type slot/port
7.
no switchport
8.
vrf member vrf-name
9.
ip-address ip-prefix/length
10.
ip router ospf instance-tag area area-id
11.
(Optional) copy running-config startup-config
DETAILED STEPS
|
|
|
Step 1 |
configure terminal Example: switch# configure terminal switch(config)# |
Enters configuration mode. |
Step 2 |
vrf context vrf-name Example: switch(config)# vrf context RemoteOfficeVRF switch(config-vrf)# |
Creates a new VRF and enters VRF configuration mode. |
Step 3 |
router ospf instance-tag Example: switch(config-vrf)# router ospf 201 switch(config-router)# |
Creates a new OSPFv2 instance with the configured instance tag. |
Step 4 |
vrf vrf-name Example: switch(config-router)# vrf RemoteOfficeVRF switch(config-router-vrf)# |
Enters VRF configuration mode. |
Step 5 |
maximum-paths paths Example : switch(config-router-vrf)# maximum-paths 4 |
(Optional) Configures the maximum number of equal OSPFv2 paths to a destination in the route table for this VRF. Used for load balancing. |
Step 6 |
interface interface-type slot/port Example : switch(config-router-vrf)# interface ethernet 1/2 switch(config-if)# |
Enters interface configuration mode. |
Step 7 |
no switchport Example: switch(config-if)# no switchport |
Configures the interface as a Layer 3 routed interface. |
Step 8 |
vrf member vrf-name Example: switch(config-if)# vrf member RemoteOfficeVRF |
Adds this interface to a VRF. |
Step 9 |
ip address ip-prefix/length Example: switch(config-if)# ip address 192.0.2.1/16 |
Configures an IP address for this interface. You must do this step after you assign this interface to a VRF. |
Step 10 |
ip router ospf instance-tag area area-id Example: switch(config-if)# ip router ospf 201 area 0 |
Assigns this interface to the OSPFv2 instance and area configured. |
Step 11 |
copy running-config startup-config Example: switch(config)# copy running-config startup-config |
(Optional) Saves this configuration change. |
This example shows how to create a VRF and add an interface to the VRF:
switch# configure terminal
switch(config)# vrf context NewVRF
switch(config)# router ospf 201
switch(config)# interface ethernet 1/2
switch(config-if)# no switchport
switch(config-if)# vrf member NewVRF
switch(config-if)# ip address 192.0.2.1/16
switch(config-if)# ip router ospf 201 area 0
switch(config)# copy running-config startup-config