New and Changed Information
This table summarizes the new and changed features for the Cisco Nexus 9000 Series NX-OS Label Switching Configuration Guide, Release 7.x and tells you where they are documented.
Feature |
Description |
Changed in Release |
Where Documented |
---|---|---|---|
Local label allocation |
Added support for IPv4 and IPv6 labeled and unlabeled unicast route on a single BGP session. This behavior is the same irrespective of whether one or both SAFI-1 and SAFI-4 are enabled on the same session or not. |
7.0(3)I7(6) |
About Labeled and Unlabeled Unicast Paths |
TCAM Capacity |
Introduces the show hardware internal forwarding table utilization command. |
7.0(3)I7(5) |
|
Static MPLS |
Adds support for the Cisco Nexus 9300-FX platform switches and the N9K-X9700-FX line cards. |
7.0(3)I7(5) |
|
Segment Routing |
Introduced MPLS Time-to-Live (TTL). |
7.0(3)I7(5) |
|
MPLS QoS |
Introduced this feature on the Cisco Nexus 9300-EX, 9300-FX platform switches, N9K-X9700-FX, and N9K-X9700-EX line cards. |
7.0(3)I7(5) |
|
MPLS Queuing |
Introduced this feature. |
7.0(3)I7(5) |
|
Segment Routing Application (SR-APP) module |
Added support for Segment Routing Application (SR-APP) module for BGP and IS-IS protocols. |
7.0(3)I7(3) |
|
Segment Routing with IS-IS Protocol |
Added support for configuring Segment Routing with IS-IS protocol. |
7.0(3)I7(3) |
|
Segment Routing |
Added support for configuring Segment Routing on Cisco Nexus N9K-X9736C-FX line cards. |
7.0(3)I7(3) |
|
InterAS Option B |
Added support for InterAS Option B for Cisco Nexus 9508 platform switches with the N9K-X9636C-R, N9K-X9636C-RX, and N9K-X9636Q-R line cards. |
7.0(3)F3(3) |
|
MPLS and VXLAN |
Added support for multiple hardware profile to configure MPLS and VXLAN on Cisco Nexus 9508 platform switches with the N9K-X9636C-R, N9K-X9636C-RX, and N9K-X9636Q-R line cards. |
7.0(3)F3(3) |
|
VPNv4 Multipath |
Introduced this feature for Cisco Nexus 9508 platform switches with the N9K-X9636C-R, N9K-X9636C-RX, and N9K-X9636Q-R line cards. |
7.0(3)F3(3) |
|
MPLS L3 VPN |
Added support for this feature for Cisco Nexus 9508 platform switches with the N9K-X9636C-R, N9K-X9636C-RX, and N9K-X9636Q-R line cards. |
7.0(3)F3(3) |
|
Support for Cisco Nexus 9300-FX platform switches |
Added support for segment routing, Layer 3 EVPN, SR OAM, MPLS Label Stack Imposition, Egress Peer Engineering, Static MPLS, and MPLS Stripping on Cisco Nexus 9300-FX platform switches |
7.0(3)I7(1) |
|
Configuring MPLS Segment Routing OAM |
Added support for configuring MPLS Segment Routing OAM. |
7.0(3)I6(1) |
|
Configuring EVPN over Segment Routing MPLS |
Added support for configuring EVPN over Segment Routing MPLS. |
7.0(3)I6(1) |
|
Configuring BGP EVPN and Label Allocation Mode |
Added support for configuring BGP EVPN and Label Allocation Mode. |
7.0(3)I6(1) |
|
MPLS label stack imposition |
Added support for MPLS label stack imposition. |
7.0(3)I5(2) |
|
Configuring Egress Peer Engineering |
Added support for configuring Egress Peer Engineering. |
7.0(3)I5(1) |
Overview of BGP Egress Peer Engineering With Segment Routing |
Configuring the BGP Link State Address Family |
Added support for configuring the BGP Link State Address Family. |
7.0(3)I5(1) |
|
Support for segment routing, static MPLS, and MPLS stripping on Cisco Nexus 9300-EX Series switches |
Added support for segment routing, static MPLS, and MPLS stripping on Cisco Nexus 9300-EX Series switches |
7.0(3)I5(1) |
|
Segment Routing |
Added support for configuring Segment Routing. |
7.0(3)I3(1) |
|
Static MPLS |
Replaced the mpls ip static command with the mpls ip forwarding command to enable MPLS on an interface. |
7.0(3)I3(1) |
|
Static MPLS |
Introduced this feature. |
7.0(3)I2(1) |