Configuring Macros
Auto Smartports Configuration Guidelines
- You cannot delete or change the built-in macros. However, you can override a built-in macro by creating a user-defined macro with the same name. To restore the original built-in macro, delete the user-defined macro.
- If you enable both the macro auto device and the macro auto execute global configuration commands, the parameters specified in the command last executed are applied to the switch. Only one command is active on the switch.
- To avoid system conflicts when macros are applied, remove all port configurations except for 802.1x authentication. Be sure to enter the commands that remove port security and Bridge Protocol Data Unit (BPDU) guard features before you enable Auto Smartports macros on a port.
- Do not configure port security when you enable device-specific Auto Smartports on the switch. The switch applies the appropriate port-based commands.
- If the macro conflicts with the original configuration, either the macro does not apply some of the original configuration commands, or the antimacro does not remove them. (The antimacro is the portion of the applied macro that removes the macro at a link-down event.)
For example, if 802.1x authentication is enabled, you cannot remove the switchport-mode access configuration. Remove the 802.1x authentication before removing the switchport mode configuration.
- A port cannot be a member of an EtherChannel when you apply Auto Smartports macros. If you use EtherChannels, disable Auto Smartports on the EtherChannel interface by using the no macro auto processing interface configuration command.
- The built-in macro default data VLAN is VLAN 1. The built-in macro default voice VLAN is VLAN 2. If your switch uses different access, native, or voice VLANs, use the macro auto device or the macro auto execute global configuration commands to configure the values.
- You can specify either the VLAN name or the VLAN Id in a macro. If you use the VLAN name in a macro, it must be the same name as that in the VLAN database for all switches in the VLAN Trunking Protocol (VTP) domain. If you use the VLAN Id in a macro, then you must enter the correct VLAN name, else the default VLAN is applied.
- Use the show macro auto device privileged EXEC command to display the default macros with the default parameter values, current values, and the configurable parameter list for each macro. You can also use the show shell functions privileged EXEC command to see the built-in-macro default values.
- To use 802.1x authentication or MAC authentication bypass (MAB) to detect non-Cisco devices, configure the RADIUS server to support the Cisco attribute-value pair auto-smart-port=event trigger.
- For stationary devices that do not support CDP, LLDP, MAB, or 802.1x authentication, such as network printers, configure a MAC address group with a MAC OUI-based trigger and map it to a user-defined macro with the desired configuration.
- An 802.1x-authentication-based trigger takes precedence over all other event triggers, such as Cisco Discovery Protocol (CDP) messages, Link Layer Discovery Protocol (LLDP) messages, or user-defined MAC address groups.
- The switch supports Auto Smartports macros only on directly connected devices. If multiple devices are connected, (for example, through a hub) the applied macro is associated with the first detected device.
- If authentication is enabled on a port, the switch ignores a MAC address trigger if authentication fails.
- When using MAC-address-based detection, ensure that Auto Smartports is enabled only on ports facing access devices and not on ports that face the network or an intermediate gateway switch.
- The order of CLI commands within the macro and the corresponding antimacro can be different.
- When the device identity is configured and the device is authenticated on a switch port, these RADIUS attributes could be downloaded:
–
VLAN ID and switch ACL name or number from the Cisco access control server (ACS)
–
ASP trigger name in an attribute-value (AV) pair.
After the AV pair is downloaded, the switch applies the macro on the port.
The downloaded VLAN ID or ACL name could conflict with the settings in the user-defined or builtin macro applied by the switch.
- Auto Smartports does not support lightweight access points in the Remote Edge Access Point (REAP) or Hybrid Remote Edge Access Point (HREAP) mode.
- When configuring macros, you must enter a description. If the link is down (command $LINKUP == NO), you must enter the no macro description command. These commands are mandatory for Auto Smartports to work.
- When a Cisco switch is detected on the Auto Smartport, you have to manually map the event trigger to either a built-in macro or user-defined macro. You need to also match the event trigger to the device PID.
Enabling Auto Smartports Macros
Follow this required procedure to enable macros globally on the switch.
Beginning in privileged EXEC mode:
|
|
|
Step 1 |
configure termina l
Switch# configure terminal |
Enters global configuration mode. |
Step 2 |
macro auto global processing
Switch(config)# macro auto global processing |
Globally enables macros on the switch. |
Step 3 |
end
Switch(config)# end |
Returns to privileged EXEC mode. |
Step 4 |
show running-config
Switch# show running-config |
Verifies that Auto Smartports is enabled. |
Step 5 |
copy running-config startup-config
Switch# copy running-config startup-config |
(Optional) Saves your entries in the configuration file. |
To return to the default setting, use the no macro auto global processing global configuration command.
To disable macros on a specific port, use the no macro auto processing interface configuration command.
Note
The no macro auto global processing does not remove the macro which is already applied to the switch.
You can use the show macro auto device, the show shell functions, and the show shell triggers privileged EXEC commands to display the event triggers and the built-in macros.
This example shows how to enable macros on the switch and then how to disable macros on a specific interface:
Switch(config)# macro auto global processing
Switch(config)# interface interface_id
Switch(config-if)# no macro auto processing
Default Auto Smartports Configuration
- Auto Smartports is globally disabled and is enabled per interface.
- Macro persistence is globally disabled and is enabled per interface.
- Cisco IOS shell is disabled. Execute the Terminal shell EXEC command to enable IOS shell.
- The switch uses these built-in macros (the defaults) when Auto Smartports is enabled for the specific devices.
Table 3-1 Device-Specific Built-In Macros
|
|
CISCO_AP_AUTO_ SMARTPORT |
This macro applies the wireless access point macro for Cisco access points. It enables standard QoS, auto-QoS, and 802.1q encapsulated trunking. It configures the native VLAN on the interface. It also enables macro persistence so that the macro remains active after a link-down event. |
CISCO_DMP_AUTO_ SMARTPORT |
This macro applies the digital media player macro for Cisco digital media players. It enables QoS trust, auto-QoS, port security, and spanning-tree protection. It configures the access VLAN for the interface and provides network protection from unknown unicast packets. Note If you enter the auto qos video media-player interface configuration command, the switch automatically uses the CDP to detect the presence or absence of a Cisco digital media player. |
CISCO_IP_CAMERA_AUTO_SMARTPORT |
This macro applies the IP camera macro for Cisco IP video surveillance cameras. It enables QoS trust, auto-QoS, port security, and spanning-tree protection. It configures the access VLAN for the interface and provides network protection from unknown unicast packets. |
CISCO_LWAP_AUTO_ SMARTPORT |
This macro applies the lightweight wireless access point macro for Cisco lightweight wireless access points. It enables QoS, port security, storm control, DHCP snooping, and spanning-tree protection. It configures the access VLAN for the interface and provides network protection from unknown unicast packets. |
CISCO_PHONE_AUTO_ SMARTPORT |
This macro applies the IP phone macro for Cisco IP phones. It enables QoS, port security, storm control, DHCP snooping, and spanning-tree protection. It also configures the access and voice VLANs for that interface. |
CISCO_ROUTER_AUTO_ SMARTPORT |
This macro applies the router macro for Cisco routers. It enables QoS and trunking with 802.1Q encapsulation and spanning-tree bridge protocol data unit (BPDU) protection. |
CISCO_SWITCH_AUTO_SMARTPORT |
This macro applies the switch macro for Cisco switches. It enables QoS and trunking with 802.1q encapsulation. It also configures the native VLAN on the interface. |
- The access point macros have these enhancements:
–
The switch determines the access point type (autonomous or lightweight) and then applies the appropriate macro.
–
To reduce overrun errors at the ingress interface on an access point Ethernet receiver, the switch adds the QoS bandwidth setting to the access point macros when it receives a CDP message with the auto-QoS type, length, and value attributes (TLVs). QoS derives the bandwidth value from the auto-QoS TLVs.
If the CDP messages does not have the auto-QoS TLVs, the switch does not add the bandwidth setting to the macros.
Note
If you do not upgrade the access point image to one that has the auto-QoS TLVs, the switch does not add the bandwidth setting to the access point macros. When you configure the bandwidth before the link to the receiver goes down, the setting is removed when the link comes up.
If you add a macro command that sets the QoS bandwidth and the switch applies the macro to an access point that does not support the auto-QoS TLVs, the command is not applied to the access point, We recommend that you create a user-defined macro without that command.
–
When a Catalyst 3650 switch is connected to a Cisco Aironet 1250 access point, the switch applies a power setting to allocate up to 20 W.
Configuring Auto Smartports Parameter Values
The switch automatically maps from event triggers to built-in device-specific macros. You can follow this optional procedure to replace macro default parameter values with values that are specific to your switch.
Beginning in privileged EXEC mode:
|
|
|
Step 1 |
show macro auto device
Switch# show macro auto device |
Displays the macro default parameter values. |
Step 2 |
configure terminal
Switch# configure terminal |
Enters global configuration mode. |
Step 3 |
macro auto device { access-point | ip-camera | lightweight-ap | media-player | phone | router | switch } [ parameter=value ]
Switch(config)# macro auto device router |
Replaces the specified macro default parameter values. Enter new values in the form of a name-value pair separated by spaces: [< name1 >=< value1 > < name2 >=< value2 >...]. You can enter the VLAN ID or the VLAN name when specifying VLAN parameter values. Default values are shown for each macro default parameter value:
- access-point NATIVE_VLAN=1
- ip-camera ACCESS_VLAN=1
- lightweight-ap ACCESS_VLAN=1
- media-player ACCESS_VLAN=1
- phone ACCESS_VLAN=1 VOICE_VLAN=2
- router NATIVE_VLAN=1
- switch NATIVE_VLAN=1
Note You must enter the correct parameter name (for example, VOICE_VLAN) because this text string must match the text string in the built-in macro definition. |
Step 4 |
end
Switch(config)# end |
Returns to privileged EXEC mode. |
Step 5 |
show macro auto device
Switch# show macro auto device |
Verifies your entries. |
Step 6 |
copy running-config startup-config
Switch# copy running-config startup-config |
(Optional) Saves your entries in the configuration file. |
This example shows how to see the IP phone macro parameter values and how to change the default voice VLAN to 20. When you change the default values, they are not immediately applied on the interfaces with existing applied macros. The configured values are applied at the next link-up event. Note that the exact text string was used for VOICE_VLAN. The entry is case sensitive.
Switch# show macro auto device phone
Default Macro:CISCO_PHONE_AUTO_SMARTPORT
Current Macro:CISCO_PHONE_AUTO_SMARTPORT
Configurable Parameters:ACCESS_VLAN VOICE_VLAN
Defaults Parameters:ACCESS_VLAN=1 VOICE_VLAN=2
Current Parameters:ACCESS_VLAN=1 VOICE_VLAN=2
Switch# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)# macro auto device phone VOICE_VLAN=20
Switch# show macro auto device phone
Default Macro:CISCO_PHONE_AUTO_SMARTPORT
Current Macro:CISCO_PHONE_AUTO_SMARTPORT
Configurable Parameters:ACCESS_VLAN VOICE_VLAN
Defaults Parameters:ACCESS_VLAN=1 VOICE_VLAN=2
Current Parameters:voice_vlan=20
Configuring MAC Address Groups
For devices such as printers that do not support neighbor discovery protocols such as CDP or LLDP, use the MAC-address-based trigger configurations. This optional procedure requires these steps:
1.
Configure a MAC-address-based trigger by using the macro auto mac-address global configuration command.
2.
Associate the MAC address trigger to a built-in or a user-defined macro by using the macro auto execute global configuration command.
Beginning in privileged EXEC mode:
|
|
|
Step 1 |
configure terminal
Switch# configure terminal |
Enters global configuration mode. |
Step 2 |
macro auto mac-address-group name
Switch(config)# macro auto mac-address-group address_trigger |
Specifies the group name, and enter MAC address configuration mode. |
Step 3 |
mac-address list list | [ oui [ list list | range start-value size number ]]
Switch(config-addr-grp-mac)# mac-address list 2222.3333.3334 22.33.44 a.b.c |
Configures a list of MAC addresses separated by spaces. Specify an operationally unique identifier (OUI) list or range. The OUI is the first three bytes of the MAC address and identifies the manufacturer of the product. Specifying the OUI allows devices that do not support neighbor discovery protocols to be recognized.
- list —Enter an OUI list in hexadecimal format separated by spaces.
- range —Enter the starting OUI hexadecimal value ( start-value).
- size —Enter the length of the range ( number) from 1 to 5 to create a list of sequential addresses.
|
Step 4 |
exit
Switch(mac-adress-config) exit |
Returns to configuration mode. |
Step 5 |
macro auto execute address_trigger built-in macro name
Switch(config)# macro auto execute address_trigger builtin CISCO_PHONE_AUTO_SMARTPORT |
Maps the MAC address-group trigger to a built-in or user-defined macro. |
Step 6 |
end
Switch(config)# end |
Returns to privileged EXEC mode. |
Step 7 |
show macro auto address-group name
Switch# show macro auto address-group group2 |
Verifies your entries. |
Step 8 |
copy running-config startup-config
Switch# copy running-config startup-config |
(Optional) Saves your entries in the configuration file. |
This example shows how to create a MAC-address-group event trigger called address_trigger, map it to the built in phone macro, and verify your entries:
Switch# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)# macro auto mac-address-group address_trigger
Switch(config-addr-grp-mac)# mac-address list 2222.3333.3334 22.33.44 a.b.c
Switch(config-addr-grp-mac)# oui list 455555 233244
Switch(config-addr-grp-mac)# oui range 333333 size 2
Switch(config-addr-grp-mac)# exit
Switch(config)# macro auto execute address_trigger builtin CISCO_PHONE_AUTO_SMARTPORT
Switch# show running configuration | include macro
macro auto mac-address-group address_trigger
mac auto execute address_trigger builtin CISCO_PHONE_AUTO_SMARTPORT
macro description CISCO_DMP_EVENT
mac description CISCO_SWITCH_EVENT
The example shows how to create an OUI list with five sequential addresses starting with 00000A and how to verify your entries:
Switch# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)# macro auto mac-address-group size5ouilist
Switch(config-addr-grp-mac)# oui range 00000A size 5
Switch(config-addr-grp-mac)# exit
Switch(config)# mac auto execute size5ouilist builtin macro
Switch(config)# macro auto execute size5ouilist builtin CISCO_PHONE_AUTO_SMARTPORT
Switch# show running configuration | include oui
Configuring Macro Persistence
When you enable Auto Smartports on the switch, by default the macro configuration is applied at a link-up event and removed at a link-down event. When you enable macro persistence, the configuration is applied at link-up and is not removed at link-down. The applied configuration remains. Macro persistence remains configured after a reboot if you have saved the running configuration file.
Follow this optional procedure so that enable macros remain active on the switch after a link-down event.
Beginning in privileged EXEC mode:
|
|
|
Step 1 |
configure terminal
Switch# configure terminal |
Enters global configuration mode. |
Step 2 |
interface interface-id
Switch(config)# interface gigabitethernet 2/0/1 |
Specifies an interface and enters interface configuration mode. |
Step 3 |
macro auto sticky
Switch(config-if)# macro auto port sticky |
Enables macros to remain active on the interface after a link-down event. |
Step 4 |
end
Switch(config)# end |
Returns to privileged EXEC mode. |
Step 5 |
show running-config interface interface-id
Switch# show running-config interface gigabit ethernet 2/0/1 |
Verifies your entries. |
Step 6 |
copy running-config startup-config
Switch# copy running-config startup-config |
(Optional) Saves your entries in the configuration file. |
This example shows how to enable macro persistence on an interface:
Switch# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)# interface gigabitethernet 2/0/1
Switch(config-if)# macro auto port sticky
Switch# show running-config interface gigabitethernet 2/0/1
Building configuration...
Current configuration : 243 bytes
interface GigabitEthernet2/0/1
srr-queue bandwidth share 1 30 35 5
mls qos trust device cisco-phone
service-policy input AUTOQOS-ENHANCED-CISCOPHONE-POLICY
Configuring Built-In Macro Options
Use this procedure to map event triggers to built-in macros and to replace the built-in macro default parameters with values that are specific to your switch. If you need to replace default parameters values in a macro, use the macro auto device global configuration command. All commands in this procedure are optional.
Beginning in privileged EXEC mode:
|
|
|
Step 1 |
configure terminal
Switch# configure terminal |
Enters global configuration mode. |
Step 2 |
macro auto execute event trigger builtin built-in macro name [ parameter=value ] [ parameter=value ]
Switch(config)# macro auto execute CISCO_PHONE_EVENT builtin CISCO_PHONE_AUTO_SMARTPORT ACCESS_VLAN=10 VOICE_VLAN=20 |
Defines mapping from an event trigger to a built-in macro. Specify an event trigger :
- CISCO_DMP_EVENT
- CISCO_IP_CAMERA_EVENT
- CISCO_PHONE_EVENT
- CISCO_ROUTER_EVENT
- CISCO_SWITCH_EVENT
- CISCO_WIRELESS_AP_EVENT
- CISCO_WIRELESS_LIGHTWEIGHT_AP_EVENT
- WORD—Apply a user-defined event trigger.
Specify a builtin built-in macro name : Enter new values in the form of name value pair separated by spaces: [< name1 >=< value1 > < name2 >=< value2 >...]. Default values are shown exactly as they should be entered.
- CISCO_AP_AUTO_SMARTPORT
Specify the parameter value: NATIVE_VLAN=1.
- CISCO_DMP_AUTO_SMARTPORT
Specify the parameter value: ACCESS_VLAN=1.
- CISCO_IP_CAMERA_AUTO_SMARTPORT
Specify the parameter value: ACCESS_VLAN=1.
- CISCO_LWAP_AUTO_SMARTPORT
Specify the parameter value: ACCESS_VLAN=1.
- CISCO_PHONE_AUTO_SMARTPORT
Specify the parameter values: ACCESS_VLAN=1 and VOICE_VLAN=2.
- CISCO_ROUTER_AUTO_SMARTPORT
Specify the parameter value: NATIVE_VLAN=1.
- CISCO_SWITCH_AUTO_SMARTPORT
Specify the parameter value: NATIVE_VLAN=1.
|
Step 3 |
remote url
Switch(config)# remote nvram://user:password@/C/macros |
Specifies a remote server location for the remote macro file:
- The syntax for the local flash file system on the standalone switch or the stack master: flash:
- The syntax for the local flash file system on a stack member:
flash member number:
- The syntax for the FTP: ftp: [[ //username [ :password ] @location ]/ directory ] /filename
- The syntax for an HTTP server:
http:// [[ username:password ] @ ]{ hostname | host-ip }[/ directory ] /filename
- The syntax for a secure HTTP server:
https:// [[ username:password ] @ ]{ hostname | host-ip }[/ directory ] /filename
- The syntax for NVRAM:
nvram:// [[ username:password ] @ ][/ directory ] /filename
- The syntax for the Remote Copy Protocol (RCP):
rcp: [[ //username@location ]/ directory ] /filename
- The syntax for the Secure Copy Protocol (SCP):
scp: [[// username@location ]/ directory ]/ filename
- The syntax for the TFTP:
tftp: [[ //location ]/ directory ] /filename
|
Step 4 |
end
Switch(config)# end |
Returns to privileged EXEC mode. |
Step 5 |
show running-config
Switch# show running-config |
Verifies that Auto Smartports is enabled. |
Step 6 |
copy running-config startup-config
Switch# copy running-config startup-config |
(Optional) Saves your entries in the configuration file. |
This example shows how to use two built-in macros to connect Cisco switches and Cisco IP phones to the switch. This example modifies the default voice VLAN, access VLAN, and native VLAN for the trunk interface:
Note
The modified value takes effect on the next link-up event or if the auto smartport is enabled after configuring the value. If the macro is already applied on an interface, then the modified value does not take effect for that interface.
Switch# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#!!! the next command modifies the access and voice vlans
Switch(config)#!!! for the built in Cisco IP phone auto smartport macro
Switch(config)# macro auto execute CISCO_PHONE_EVENT builtin CISCO_PHONE_AUTO_SMARTPORT ACCESS_VLAN=10 VOICE_VLAN=20
Switch(config)#!!! the next command modifies the Native vlan used for inter switch trunks
Switch(config)# macro auto execute CISCO_SWITCH_EVENT builtin CISCO_SWITCH_AUTO_SMARTPORT NATIVE_VLAN=10
Switch(config)#!!! the next command enables auto smart ports globally
Switch(config)# macro auto global processing
Switch# !!! here is the running configuration of the interface connected
Switch# !!! to another Cisco Switch after the Macro is applied
Switch# show running-config interface gigabitethernet1/0/1
Building configuration...
Current configuration : 284 bytes
interface GigabitEthernet1/0/1
switchport trunk encapsulation dot1q
switchport trunk native vlan 10
srr-queue bandwidth share 10 10 60 20
macro description CISCO_SWITCH_EVENT
This example shows how to configure the remote macro for native VLAN 5:
1. Configuring the remote macro in the macro.txt file.
2. Using the macro auto execute configuration command to specify the remote location for the macro file. In this step, note that the macro content is downloaded everytime there is a link up or link down event. Any changes made after the macro is applied or removed is reflected in the next event (macro application or removal).
Macro.txt file
if [[ $LINKUP == YES ]]; then
macro description $TRIGGER
switchport trunk encapsulation dot1q
switchport trunk native vlan $NATIVE_VLAN
switchport trunk allowed vlan ALL
no switchport trunk encapsulation dot1q
no switchport trunk native vlan $NATIVE_VLAN
no switchport trunk allowed vlan ALL
Switch(config)# macro auto execute CISCO_SWITCH_EVENT remote tftp://<ip_address>/macro.txt NATIVE_VLAN=5
In the following step you must enter the correct IP address of the remote location.
Switch# show running configuration | include macro
macro auto execute CISCO_SWITCH_EVENT remote tftp://<ip_address>/macro.txt
Configuring Mapping Between Event Triggers and Built-in Macros
Note
You need to perform this task when a Cisco switch is connected to the Auto Smartport.
To map event trigger to a built-in macros, perform this task:
|
|
|
Step 1 |
Switch#
configure terminal
|
Enters global configuration mode. |
Step 2 |
Switch(config)# macro auto execute
event trigger
builtin
built-in macro name
|
Specifies a user-defined event trigger and a macro name. This action configures mapping from an event trigger to a built-in Auto Smartports macro. |
Step 3 |
Switch(config)#
macro auto trigger
event trigger
|
Invokes the user-defined event trigger. |
Step 4 |
Switch(config)#
device
device_ID
|
Matches the event trigger to the device identifier. |
Step 5 |
|
Returns to privileged EXEC mode. |
Step 6 |
Switch#
show shell triggers
|
Displays the event triggers on the switch. |
Step 7 |
Switch#
copy running-config startup-config
|
(Optional) Saves your entries in the configuration file. |
This example shows how to map a event trigger called CISCO_SWITCH_EVENT to the built-in macro CISCO_SWITCH_AUTO_SMARTPORT.
Switch(config)# macro auto execute CISCO_SWITCH_EVENT builtin CISCO_SWITCH_AUTO_SMARTPORT
Switch(config)# macro auto trigger CISCO_SWITCH_EVENT
Switch(config)# device cisco WS-C3560CX-8PT-S
Creating User-Defined Event Triggers
When using MAB or 802.1x authentication as an event trigger, create a trigger that corresponds to the Cisco attribute-value pair ( auto-smart-port =event trigger) sent by the RADIUS server. This procedure is optional.
Beginning in privileged EXEC mode:
|
|
|
Step 1 |
configure terminal
Switch# configure terminal |
Enters global configuration mode. |
Step 2 |
shell trigger identifier description
Switch(config)# shell trigger RADIUS_MAB_EVENT MAC_AuthBypass Event |
Specifies the event trigger identifier and description. The identifier should have no spaces or hyphens between words. |
Step 3 |
end
Switch(config)# end |
Returns to privileged EXEC mode. |
Step 4 |
show shell triggers
Switch# show shell triggers |
Displays the event triggers on the switch. |
Step 5 |
copy running-config startup-config
Switch# copy running-config startup-config |
(Optional) Saves your entries in the configuration file. |
This example shows how to map a user-defined event trigger called RADIUS_MAB_EVENT to the built-in macro CISCO_AP AUTO_SMARTPORT, to replace the default VLAN with VLAN 10, and how to verify the entries.
1.
Connect the device to a MAB-enabled switch port.
2.
On the RADIUS server, set the attribute-value pair to auto-smart-port =RADIUS_MAB_EVENT.
3.
On the switch, create the event trigger RADIUS_MAB_EVENT.
4.
The switch recognizes the attribute-value pair=RADIUS_MAB_EVENT response from the RADIUS server and applies the macro CISCO_AP_AUTO_SMARTPORT.
Switch# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)# !!! create a user defined trigger and map
Switch(config)# !!! a system defined macro to it
Switch(config)# !!! first create the trigger event
Switch(config)# shell trigger RADIUS_MAB_EVENT MAC_AuthBypass Event
Switch(config)#!!! map a system defined macro to the trigger event
Switch(config)# macro auto execute RADIUS_MAB_EVENT builtin ?
CISCO_AP_AUTO_SMARTPORT Configure native vlan and trust cos
CISCO_CUSTOM_AUTOSMARTPORT Configure user defined parameters
CISCO_DMP_AUTO_SMARTPORT Configure access vlan, qos and port-security
CISCO_IP_CAMERA_AUTO_SMARTPORT Configure access vlan, qos and port-security
CISCO_LAST_RESORT_SMARTPORT Configure access vlan
CISCO_LWAP_AUTO_SMARTPORT Configure native vlan, qos, port-security and
CISCO_PHONE_AUTO_SMARTPORT Configure access vlan, voice vlan, trust
device, interface bandwidth, port-security
CISCO_ROUTER_AUTO_SMARTPORT Configure native vlan, spanning tree
port-fast,trunk mode and trust dscp
CISCO_SWITCH_AUTO_SMARTPORT Configure native vlan, trunk mode
Switch(config)# macro auto execute RADIUS_MAB_EVENT builtin CISCO_AP_AUTO_SMARTPORT ACCESS_VLAN=10
Switch# show shell triggers
Trigger Id: RADIUS_MAB_EVENT
Trigger description: MAC_AuthBypass Event
Trigger mapping function: CISCO_AP_SMARTPORT
This example shows how to use the show shell triggers privileged EXEC command to view the event triggers in the switch software:
Switch# show shell triggers
Trigger Id: CISCO_DMP_EVENT
Trigger namespace: ASP_TRIG
Trigger description: Digital media-player device event to apply port configuration
Trigger mapping function: CISCO_DMP_AUTO_SMARTPORT
Trigger Id: CISCO_IPVSC_EVENT
Trigger namespace: ASP_TRIG
Trigger description: IP-camera device event to apply port configuration
Trigger mapping function: CISCO_IP_CAMERA_AUTO_SMARTPORT
Trigger Id: CISCO_PHONE_EVENT
Trigger namespace: ASP_TRIG
Trigger description: IP-phone device event to apply port configuration
Trigger mapping function: CISCO_PHONE_AUTO_SMARTPORT
Trigger Id: CISCO_ROUTER_EVENT
Trigger namespace: ASP_TRIG
Trigger description: Router device event to apply port configuration
Trigger mapping function: CISCO_ROUTER_AUTO_SMARTPORT
Trigger Id: CISCO_SWITCH_EVENT
Trigger namespace: ASP_TRIG
Trigger description: Switch device event to apply port configuration
Trigger mapping function: CISCO_SWITCH_AUTO_SMARTPORT
Trigger Id: CISCO_WIRELESS_AP_EVENT
Trigger namespace: ASP_TRIG
Trigger description: Autonomous ap device event to apply port configuration
Trigger mapping function: CISCO_AP_AUTO_SMARTPORT
Trigger Id: CISCO_WIRELESS_LIGHTWEIGHT_AP_EVENT
Trigger namespace: ASP_TRIG
Trigger description: Lightweight-ap device event to apply port configuration
Trigger mapping function: CISCO_LWAP_AUTO_SMARTPORT
This example shows how to use the show shell functions privileged EXEC command to view the built-in macros in the switch software:
Switch# show shell functions
function CISCO_AP_AUTO_SMARTPORT () {
if [[ $LINKUP == YES ]]; then
macro description $TRIGGER
switchport trunk encapsulation dot1q
switchport trunk native vlan $NATIVE_VLAN
switchport trunk allowed vlan ALL
if [[ $LIMIT == 0 ]]; then
default srr-queue bandwidth limit
srr-queue bandwidth limit $LIMIT
if [[ $SW_POE == YES ]]; then
if [[ $AP125X == AP125X ]]; then
power inline port maximum 20000
if [[ $LINKUP == NO ]]; then
no switchport nonegotiate
no switchport trunk native vlan $NATIVE_VLAN
no switchport trunk allowed vlan ALL
default srr-queue bandwidth limit
if [[ $AUTH_ENABLED == NO ]]; then
no switchport trunk encapsulation
if [[ $STICKY == YES ]]; then
if [[ $SW_POE == YES ]]; then
if [[ $AP125X == AP125X ]]; then
no macro auto port sticky
no power inline port maximum
Configuring User-Defined Macros
The Cisco IOS shell has basic scripting capabilities for configuring user-defined macros. These macros can contain multiple lines and can include any CLI command. You can also define variable-substitution, conditionals, functions, and triggers within the macro. This procedure is optional.
Note
When configuring macros, you must enter a description. If the link is down (command $LINKUP == NO), you must enter the no macro description command. These commands are mandatory for Auto Smartports to work.
Beginning in privileged EXEC mode, follow these steps to map a user-defined event trigger to a user-defined macro.
|
|
|
Step 1 |
configure terminal
Switch# configure terminal |
Enters global configuration mode. |
Step 2 |
macro auto execute event trigger [ parameter=value ] { function contents }
Switch(config)# macro auto execute DMP_EVENT { if [[ $LINKUP == YES ]]; then conf t interface $INTERFACE macro description $TRIGGER switchport access vlan 1 switchport mode access switchport port-security switchport port-security maximum 1 switchport port-security violation restrict switchport port-security aging time 2 switchport port-security aging type inactivity spanning-tree portfast spanning-tree bpduguard enable exit fi if [[ $LINKUP == NO ]]; then conf t interface $INTERFACE no macro description no switchport access vlan 1 if [[ $AUTH_ENABLED == NO ]]; then no switchport mode access fi no switchport port-security no switchport port-security maximum 1 no switchport port-security violation restrict no switchport port-security aging time 2 no switchport port-security aging type inactivity no spanning-tree portfast no spanning-tree bpduguard enable exit fi } |
Specifies a user-defined macro that maps to an event trigger. { function contents } Specify a user-defined macro to associate with the trigger. Enter the macro contents within braces. Begin the Cisco IOS shell commands with the left brace and end the command grouping with the right brace. (Optional) parameter=value —Replace default values that begin with $, and enter new values in the form of name value pair separated by spaces: [< name1 >=< value1 > < name2 >=< value2 >...]. |
Step 3 |
end
Switch(config)# end |
Returns to privileged EXEC mode. |
Step 4 |
show running-config
Switch# show running-config |
Verifies that Auto Smartports is enabled. |
Step 5 |
copy running-config startup-config
Switch# copy running-config startup-config |
(Optional) Saves your entries in the configuration file. |
Example: User-Defined Event Trigger and Macro
This example shows how to map a user-defined event trigger called media player to a user-defined macro.
1.
Connect the media player to an 802.1x- or MAB-enabled switch port.
2.
On the RADIUS server, set the attribute-value pair to auto-smart-port =DMP_EVENT.
3.
On the switch, create the event trigger DMP_EVENT, and enter the user-defined macro commands in the CLI example.
4.
The switch recognizes the attribute-value pair=DMP_EVENT response from the RADIUS server and applies the macro associated with this event trigger.
Note
While making the mapping changes enter the space and the semicolon exactly the same way as mentioned in the following example.
Switch(config)# shell trigger DMP_EVENT mediaplayer
Switch(config)# macro auto execute DMP_EVENT {
if [[ $LINKUP == YES ]]; then
macro description $TRIGGER
switchport port-security maximum 1
switchport port-security violation restrict
switchport port-security aging time 2
switchport port-security aging type inactivity
spanning-tree bpduguard enable
if [[ $LINKUP == NO ]]; then
no switchport access vlan 1
if [[ $AUTH_ENABLED == NO ]]; then
no switchport mode access
no switchport port-security
no switchport port-security maximum 1
no switchport port-security violation restrict
no switchport port-security aging time 2
no switchport port-security aging type inactivity
no spanning-tree portfast
no spanning-tree bpduguard enable
Example: User Defined Macro Triggered by MAC Address
This example shows how to create your own auto smartport macro and then bind a MAC address to that macro.
macro auto mac-address-group TRIGGER_PRINTER_MAC
macro auto execute TRIGGER_PRINTER_MAC ACCESS_VLAN=10 {
macro description $TRIGGER
switchport access vlan $ACCESS_VLAN
switchport port-security maximum 1
switchport port-security violation protect
spanning-tree bpduguard enable
no switchport access vlan $ACCESS_VLAN
no switchport block unicast
no switchport port-security
no switchport port-security maximum 1
no switchport port-security violation protect
no spanning-tree portfast
no spanning-tree bpduguard enable
Table 3-2 Supported Cisco IOS Shell Keywords
|
|
{ |
Begin the command grouping. |
} |
End the command grouping. |
[[ |
Use as a conditional construct. |
]] |
Use as a conditional construct. |
else |
Use as a conditional construct. |
== |
Use as a conditional construct. |
fi |
Use as a conditional construct. |
if |
Use as a conditional construct. |
then |
Use as a conditional construct. |
-z |
Use as a conditional construct. |
$ |
Variables that begin with the $ character are replaced with a parameter value. |
# |
Use the # character to enter comment text. |
Table 3-3 Unsupported Cisco IOS Shell Reserved Keywords
|
|
| |
Pipeline. |
case |
Conditional construct. |
esac |
Conditional construct. |
for |
Looping construct. |
function |
Shell function. |
in |
Conditional construct. |
select |
Conditional construct. |
time |
Pipeline. |
until |
Looping construct. |
while |
Looping construct. |
Default Static Smartports Configuration
There are no static Smartports macros enabled on the switch.
Table 3-4 Default Static Smartports Macros
|
|
cisco-global |
Use this global configuration macro to enable rapid per-VLAN spanning-tree plus (PVST+), loop guard, and dynamic port-error recovery for link state failures. |
cisco-desktop |
Use this interface configuration macro for increased network security and reliability when connecting a desktop device, such as a PC, to a switch port. |
cisco-phone |
Use this interface configuration macro when connecting a desktop device such as a PC with a Cisco IP Phone to a switch port. This macro is an extension of the cisco-desktop macro and provides the same security and resiliency feature and also dedicated voice VLANs to ensure proper treatment of delay-sensitive voice traffic. |
cisco-switch |
Use this interface configuration macro when connecting an access switch and a distribution switch or between access switches connected through small form-factor pluggable (SFP) modules. |
cisco-router |
Use this interface configuration macro when connecting the switch and a WAN router. |
cisco-wireless |
Use this interface configuration macro when connecting the switch and a wireless access point. |
Static Smartports Configuration Guidelines
- When a macro is applied globally to a switch or to a switch interface, the existing configuration on the interface is retained. This is helpful when applying an incremental configuration.
- If a command fails because of a syntax or a configuration error, the macro continues to apply the remaining commands. You can use the macro global trace macro-name global configuration command or the macro trace macro-name interface configuration command to apply and then debug the macro to find any syntax or configuration errors.
- Some CLI commands are specific to certain interface types. If you apply a macro to an interface that does not accept the configuration, the macro fails the syntax or the configuration check, and the switch returns an error message.
- Applying a macro to an interface range is the same as applying a macro to a single interface. When you use an interface range, the macro is applied sequentially to each interface within the range. If a macro command fails on one interface, it is still applied to the remaining interfaces.
- When you apply a macro to a switch or a switch interface, the macro name is automatically added to the switch or interface. You can display the macro names and applied commands using the show running-config user EXEC command.
NEAT Configuration
The Network Edge Access Topology (NEAT) feature extends identity to areas outside the wiring closet (such as conference rooms).
In a NEAT scenario, when 802.1x authentication is successful and an ASP macro is sent from the Access Control Server (ACS) to the switch, you must make one of the following configurations:
- Change the host mode to multi-host.
- Enable trunk configuration on the authenticator switch by configuring the cisco-av-pair as device-traffic-class=switch at the ACS.
Applying Static Smartports Macros
Beginning in privileged EXEC mode:
|
|
|
Step 1 |
show parser macro
Switch# show parser macro |
Displays the Cisco-default static Smartports macros embedded in the switch software. |
Step 2 |
show parser macro name macro-name
Switch# show parser macro name cisco-desktop |
Displays the specific macro that you want to apply. |
Step 3 |
configure terminal
Switch# configure terminal |
Enters global configuration mode. |
Step 4 |
macro global { apply | trace } macro-name [ parameter { value }] [ parameter { value }] [ parameter { value }]
Switch(config)# macro global apply cisco-desktop $access_vlan 25 |
Applies a macro on the switch:
- To only apply each individual macro command, use the macro global apply macro-name command.
- To apply and then debug a macro to find any syntax or configuration errors, use the macro global trace macro-name command.
Append the macro with the required values by using the parameter value keywords. Keywords that begin with $ require a unique parameter value. You can use the macro global apply macro-name ? command to display a list of any required values for the macro. If you apply a macro without entering the keyword values, the commands are invalid and are not applied. (Optional) Specify unique parameter values that are specific to the switch. You can enter up to three keyword-value pairs. Parameter keyword matching is case sensitive. The corresponding value replaces all matching occurrences of the keyword. |
Step 5 |
interface interface-id
Switch(config)# interface gigabitethernet 2/0/5 |
(Optional) Specifies an interface and enters interface configuration mode. |
Step 6 |
default interface interface-id
Switch(config)# default interface 2/1/4 |
(Optional) Clears all configuration from the specified interface. |
Step 7 |
macro { apply | trace } macro-name [ parameter { value }] [ parameter { value }] [ parameter { value }]
Switch(config-if)# macro apply cisco-desktop $access_vlan 25 |
Applies a macro on the interface:
- To only apply each individual macro command, use the macro apply macro-name command.
- To apply and then debug a macro to find any syntax or configuration errors, use the macro trace macro-name command.
Append the macro with the required values by using the parameter value keywords. Keywords that begin with $ require a unique parameter value. You can use the macro global apply macro-name ? command to display a list of any required values for the macro. If you apply a macro without entering the keyword values, the commands are invalid and are not applied. (Optional) Specify unique parameter values that are specific to the switch. You can enter up to three keyword-value pairs. Parameter keyword matching is case sensitive. The corresponding value replaces all matching occurrences of the keyword. |
Step 8 |
end
Switch(config)# end |
Returns to privileged EXEC mode. |
Step 9 |
show running-config interface interface-id
Switch# show running-config interface gigabit ethernet 1/0/4 |
Verifies that Auto Smartports is enabled. |
Step 10 |
copy running-config startup-config
Switch# copy running-config startup-config |
(Optional) Saves your entries in the configuration file. |
You can only delete a global macro-applied configuration on a switch by entering the no version of each command in the macro. You can delete a macro-applied configuration on a port by entering the default interface interface-id interface configuration command.
This example shows how to display the cisco-desktop macro, to apply the macro, and to set the access VLAN ID to 25 on an interface:
Switch# show parser macro name cisco-desktop
--------------------------------------------------------------
Macro name : cisco-desktop
Macro type : default interface
# macro keywords $access_vlan
# Basic interface - Enable data VLAN only
# Recommended value for access vlan should not be 1
switchport access vlan $access_vlan
# Enable port security limiting port to a single
# MAC address -- that of desktop
switchport port-security maximum 1
# Ensure port-security age is greater than one minute
# and use inactivity timer
switchport port-security violation restrict
switchport port-security aging time 2
switchport port-security aging type inactivity
# Configure port as an edge network port
spanning-tree bpduguard enable
--------------------------------------------------------------
Switch# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)# interface gigabitethernet1/0/4
Switch(config-if)# macro apply cisco-desktop $access_vlan 25