BFD Support for EIGRP IPv6
The BFD Support for EIGRP IPv6 feature provides Bidirectional Forwarding Detection (BFD) support for Enhanced Interior Gateway Routing Protocol (EIGRP) IPv6 sessions, thereby facilitating rapid fault detection and alternate-path selection in EIGRP IPv6 topologies. BFD is a detection protocol that provides a consistent failure-detection method for network administrators, and network administrators use BFD to detect forwarding path failures at a uniform rate and not at variable rates for different routing protocol ‘Hello’ mechanisms. This failure-detection methodology ensures easy network profiling and planning and consistent and predictable reconvergence time. This document provides information about BFD support for EIGRP IPv6 networks and explains how to configure BFD support in EIGRP IPv6 networks.
Prerequisites for BFD Support for EIGRP IPv6
EIGRP IPv6 sessions have a shutdown option in router, address family, and address-family interface configuration modes. To enable BFD support on EIGRP IPv6 sessions, the routing process should be in no shut mode in the abovementioned modes.
Restrictions for BFD Support for EIGRP IPv6
-
The BFD Support for EIGRP IPv6 feature is supported only in EIGRP named mode.
-
EIGRP supports only single-hop Bidirectional Forwarding Detection (BFD).
-
The BFD Support for EIGRP IPv6 feature is not supported on passive interfaces.
Information About BFD Support for EIGRP IPv6
BFD for EIGRP IPv6
Bidirectional Forwarding Detection (BFD) is a detection protocol that provides fast-forwarding, path-failure detection for all media types, encapsulations, topologies, and routing protocols. The BFD Support for EIGRP IPv6 feature enables BFD to interact with the Enhanced Interior Gateway Routing Protocol (EIGRP) to create BFDv6 sessions between EIGRP neighbors. In a BFD-enabled EIGRP IPv6 session, BFD constantly monitors the forwarding path (from a local device to a neighboring device) and provides consistent failure detection at a uniform rate. Because failure detection happens at a uniform rate and not at variable rates, network profiling and planning is easier, and the reconvergence time remains consistent and predictable.
BFD is implemented in EIGRP at multiple levels; it can be implemented per interface or on all interfaces. When BFD is enabled on a specific interface, all peer relationships formed through the EIGRP “Hello” mechanism on that interface are registered with the BFD process. Subsequently, BFD establishes a session with each of the peers in the EIGRP topology and notifies EIGRP through a callback mechanism of any change in the state of any peer. When a peer is lost, BFD sends a “peer down” notification to EIGRP, and EIGRP unregisters a peer from BFD. BFD does not send a “peer up” notification to EIGRP when the peer is up because BFD now has no knowledge of the state of the peer. This behavior prevents rapid neighbor bouncing and repetitive route computations. The EIGRP “Hello” mechanism will later allow peer rediscovery and reregistration with the BFD process.
How to Configure BFD Support for EIGRP IPv6
Configuring BFD Support on All Interfaces
Procedure
Command or Action | Purpose | |
---|---|---|
Step 1 |
enable Example:
|
Enables privileged EXEC mode.
|
Step 2 |
configure terminal Example:
|
Enters global configuration mode. |
Step 3 |
ipv6 unicast-routing Example:
|
Enables the forwarding of IPv6 unicast datagrams. |
Step 4 |
interface type number Example:
|
Specifies the interface type and number, and enters the interface configuration mode. |
Step 5 |
ipv6 address ipv6-address/prefix-length Example:
|
Configures an IPv6 address. |
Step 6 |
bfd interval milliseconds min_rx milliseconds multiplier interval-multiplier Example:
|
Sets the baseline BFD session parameters on an interface. |
Step 7 |
exit Example:
|
Exits interface configuration mode and returns to global configuration mode. |
Step 8 |
router eigrp virtual-name Example:
|
Specifies an EIGRP routing process and enters router configuration mode. |
Step 9 |
address-family ipv6 autonomous-system as-number Example:
|
Enters address family configuration mode for IPv6 and configures an EIGRP routing instance. |
Step 10 |
eigrp router-id ip-address Example:
|
Sets the device ID used by EIGRP for this address family when EIGRP peers communicate with their neighbors. |
Step 11 |
af-interface default Example:
|
Configures interface-specific commands on all interfaces that belong to an address family in EIGRP named mode configurations, and enters address-family interface configuration mode. |
Step 12 |
bfd Example:
|
Enables BFD on all interfaces. |
Step 13 |
end Example:
|
Exits address-family interface configuration mode and returns to privileged EXEC mode. |
Step 14 |
show eigrp address-family ipv6 neighbors detail Example:
|
(Optional) Displays detailed information about the neighbors that are discovered by EIGRP with BFD enabled on an interface. |
Step 15 |
show bfd neighbors Example:
|
(Optional) Displays BFD information to neighbors. |
Configuring BFD Support on an Interface
Procedure
Command or Action | Purpose | |
---|---|---|
Step 1 |
enable Example:
|
Enables privileged EXEC mode.
|
Step 2 |
configure terminal Example:
|
Enters global configuration mode. |
Step 3 |
ipv6 unicast-routing Example:
|
Enables the forwarding of IPv6 unicast datagrams. |
Step 4 |
interface type number Example:
|
Specifies the interface type and number, and enters the interface configuration mode. |
Step 5 |
ipv6 address ipv6-address /prefix-length Example:
|
Configures an IPv6 address. |
Step 6 |
bfd interval milliseconds min_rx milliseconds multiplier interval-multiplier Example:
|
Sets the baseline BFD session parameters on an interface. |
Step 7 |
exit Example:
|
Exits interface configuration mode and returns to global configuration mode. |
Step 8 |
router eigrp virtual-name Example:
|
Specifies an EIGRP routing process and enters router configuration mode. |
Step 9 |
address-family ipv6 autonomous-system as-number Example:
|
Enters address family configuration mode for IPv6 and configures an EIGRP routing instance. |
Step 10 |
eigrp router-id ip-address Example:
|
Sets the device ID used by EIGRP for this address family when EIGRP peers communicate with their neighbors. |
Step 11 |
af-interface interface-type interface-number Example:
|
Configures interface-specific commands on an interface that belongs to an address family in an EIGRP named mode configuration, and enters address-family interface configuration mode. |
Step 12 |
bfd Example:
|
Enables BFD on the specified interface. |
Step 13 |
end Example:
|
Exits address-family interface configuration mode and returns to privileged EXEC mode. |
Step 14 |
show eigrp address-family ipv6 neighbors Example:
|
(Optional) Displays neighbors for which BFD has been enabled. |
Step 15 |
show bfd neighbors Example:
|
(Optional) Displays BFD information to neighbors. |
Configuration Examples for BFD Support for EIGRP IPv6
Example: Configuring BFD Support on All Interfaces
Device(config)# ipv6 unicast-routing
Device(config)# interface Ethernet0/0
Device(config-if)# ipv6 address 2001:0DB8:1::12/64
Device(config-if)# bfd interval 50 min_rx 50 multiplier 3
Device(config-if)# exit
Device(config)# router eigrp name
Device(config-router)# address-family ipv6 unicast autonomous-system 1
Device(config-router-af)# eigrp router-id 172.16.0.1
Device(config-router-af)# af-interface default
Device(config-router-af-interface)# bfd
Device(config-router-af-interface)# end
The following example displays the output for the show eigrp address-family ipv6 neighbors detail command.
Device# sh eigrp address-family ipv6 neighbors detail
EIGRP-IPv6 VR(test) Address-Family Neighbors for AS(5)
H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) Cnt Num
0 Link-local address: Et0/0 14 00:02:04 1 4500 0 4
FE80::10:2
Version 23.0/2.0, Retrans: 2, Retries: 0, Prefixes: 1
Topology-ids from peer - 0
Topologies advertised to peer: base
Max Nbrs: 0, Current Nbrs: 0
BFD sessions
NeighAddr Interface
FE80::10:2 Ethernet0/0
The following example displays the output for the show bfd neighbor command.
Device# sh bfd neighbors
IPv6 Sessions
NeighAddr LD/RD RH/RS State Int
FE80::10:2 2/0 Down Down Et0/0
Example: Configuring BFD Support on an Interface
Device(config)# ipv6 unicast-routing
Device(config)# Ethernet0/0
Device(config-if)# ipv6 address 2001:DB8:A:B::1/64
Device(config-if)# bfd interval 50 min_rx 50 multiplier 3
Device(config-if)# exit
Device(config)# router eigrp name
Device(config-router)# address-family ipv6 autonomous-system 3
Device(config-router-af)# af-interface Ethernet0/0
Device(config-router-af-interface)# bfd
Device(config-router-af-interface)# end
Additional References
Related Documents
Related Topic |
Document Title |
---|---|
Cisco IOS commands |
|
BFD commands: complete command syntax, command mode, command history, defaults, usage guidelines, and examples. |
|
EIGRP commands: complete command syntax, command mode, command history, defaults, usage guidelines, and examples. |
|
Configuring EIGRP |
“Configuring EIGRP” chapter in IP Routing: EIGRP Configuration Guide |
Technical Assistance
Description |
Link |
---|---|
The Cisco Support and Documentation website provides online resources to download documentation, software, and tools. Use these resources to install and configure the software and to troubleshoot and resolve technical issues with Cisco products and technologies. Access to most tools on the Cisco Support and Documentation website requires a Cisco.com user ID and password. |
Feature Information for BFD Support for EIGRP IPv6
The following table provides release information about the feature or features described in this module. This table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.
Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to www.cisco.com/go/cfn. An account on Cisco.com is not required.
Feature Name |
Releases |
Feature Information |
---|---|---|
BFD Support for EIGRP IPv6 |
Cisco IOS XE Gibraltar 16.11.x |
The feature was introduced. |