VideoStream Commands

ap dot11 media-stream multicast-direct

To configure multicast-direct for 2.4-GHz/5-GHz band, use the ap dot11 media-stream multicast-direct command.

ap dot11 {24ghz | 5ghz} media-stream {multicast-direct {admission-besteffort | client-maximum value | radio-maximum value} | video-redirect}

Syntax Description

multicast-direct

Configure multicast-direct for 802.11 band

admission-besteffort

Admits media stream to best-effort queue.

client-maximum value

Specifies the maximum number of streams allowed on a client.

radio-maximum value

Specifies the maximum number of streams allowed on a 2.4-GHz or a 5-GHz band.

video-redirect

Redirect non Multicast-direct video to BestEffort queue over the air.

Command Default

None

Command Modes

config

Command History

Release

Modification

Cisco IOS XE 3.2SE

This command was introduced.

Command History

Release Modification
7.6 This command was introduced in a release earlier than Release 7.6.

Usage Guidelines

Before you configure the media stream multicast-direct parameters on a 802.11 network, ensure that the network is nonoperational.

Examples

The following example shows how to configure multicast-direct for the 2.4-GHz band. 

(Cisco Controller) >Device#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Device(config)#ap dot11 24ghz media-stream multicast-direct

show ap dot11

To display 802.11 band parameters, use the show ap dot11 command.

show ap dot11 {24ghz | 5ghz} {media-stream rrc | network | profile | summary}

Syntax Description

media-stream rrc

Displays Media Stream configurations.

network

Shows network configuration.

profile

Shows profiling information for all Cisco APs.

summary

Shows configuration and statistics of 802.11b and 802.11a Cisco APs.

Command Default

None

Command Modes

User EXEC command mode or Privileged EXEC command mode

Command History

Release

Modification

Cisco IOS XE 3.2SE

This command was introduced.

Command History

Release Modification
7.6 This command was introduced in a release earlier than Release 7.6.

Usage Guidelines

None.

The following is a sample output of the show ap dot11 24ghz media-stream rrc command. 


Device#show ap dot11 24ghz media-stream rrc

Multicast-direct                 : Disabled
Best Effort                      : Disabled
Video Re-Direct                  : Disabled
Max Allowed Streams Per Radio      : Auto
Max Allowed Streams Per Client     : Auto
Max Video Bandwidth               : 0
Max Voice Bandwidth               : 75
Max Media Bandwidth               : 85
Min PHY Rate (Kbps)               : 6000
Max Retry Percentage              : 80

show wireless media-stream group

To display the wireless media-stream group information, use the show wireless media-stream group command.

show wireless media-stream group {detail groupName | summary}

Syntax Description

detail groupName

Display media-stream group configuration details of the group mentioned in the command.

summary

Display media-stream group configuration summary

Command Default

None

Command Modes

User EXEC mode or Privileged EXEC mode

Command History

Release

Modification

Cisco IOS XE 3.2SE

This command was introduced.

Command History

Release Modification
7.6 This command was introduced in a release earlier than Release 7.6.

Usage Guidelines

None.

The following is a sample output of the show wireless media-stream group detail GRP1 command. 

Device#show wireless media-stream group detail GRP1

wireless media-stream multicast-direct

To configure multicast-direct status, use the media-stream multicast-direct command. To remove the multicast-direct status, use the no form of the command.

no wireless media-stream multicast-direct

Command Default

None

Command Modes

config

Command History

Release

Modification

Cisco IOS XE 3.2SE

This command was introduced.

Command History

Release Modification
7.6 This command was introduced in a release earlier than Release 7.6.

Usage Guidelines

Media stream multicast-direct requires load based Call Admission Control (CAC) to run. WLAN quality of service (QoS) needs to be set to either gold or platinum.

Examples

The following example shows how to configure multicast-direct for a wireless LAN media stream. 


Device#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Device(config)#wireless media-stream multicast-direct

wireless media-stream

To configure various parameters, use the wireless media-stream command.

wireless media-stream group groupName [startipAddr endipAddr]

wireless media-stream group { avg-packet-size | default | exit | max-bandwidth | no | policy | qos }

wireless media-stream {multicast-direct | message [phone phone | URL URL | Notes Notes | Email Email]}

Syntax Description

group groupName

Configure multicast-direct status for a group.

startipAddr

Specifies the start IP Address for the group.

endipAddr

Specifies the End IP Address for the group.

group avg-packet-size

Configure average packet size.

group default

Set a command to its defaults.

group exit

Exit sub-mode.

group max-bandwidth

Configure maximum expected stream bandwidth in Kbps.

group no

Negate a command or set its defaults.

group policy

Configure media stream admission policy.

group qos

Configure over the air QoS class, <'video'> ONLY.

multicast-direct

Configure multicast-direct status.

message

Configure Session Announcement Message.

phone phone

Configure Session Announcement Phone number.

URL URL

Configure Session Announcement URL.

Notes Notes

Configure Session Announcement notes.

Email Email

Configure Session Announcement Email.

Command Default

Disabled

Command Modes

config

Command History

Release

Modification

Cisco IOS XE 3.2SE

This command was introduced.

Command History

Release Modification
7.6 This command was introduced in a release earlier than Release 7.6.

Usage Guidelines

Media-stream multicast-direct requires load-based Call Admission Control (CAC) to run.

Examples

The following example shows how to configure each media stream and its parameters like expected multicast destination addresses, stream bandwidth consumption and stream priority parameters. 


Device#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Device(config)#wireless media-stream group GROUP1 231.1.1.1 231.1.1.10