Examples

This example shows how to enable AAA on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# shutdown
Switch(config-wlan)# aaa-override
Switch(config-wlan)# no shutdown
Switch(config-wlan)# end

This example shows how to disable AAA on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# shutdown
Switch(config-wlan)# no aaa-override
Switch(config-wlan)# no shutdown
Switch(config-wlan)# end

Examples

This example shows how to configure RADIUS server accounting on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# accounting-list test
Switch(config-wlan)# end

This example shows how to disable RADIUS server accounting on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# no accounting-list test
Switch(config-wlan)# end

Examples

The following example shows how to configure a 802.11k neighbor list on a WLAN:

Switch(config-wlan)#assisted-roaming neighbor-list 

The following example shows the warning message when load balancing is enabled on a WLAN. Load balancing must be disabled if it is already enabled when configuring assisted roaming:

Switch(config)#wlan test-prediction 2 test-prediction
Switch(config-wlan)#client vlan 43
Switch(config-wlan)#no security wpa
Switch(config-wlan)#load-balance
Switch(config-wlan)#assisted-roaming prediction
WARNING: Enabling neighbor list prediction optimization may slow association and impact VOICE client perform.
Are you sure you want to continue? (y/n)[y]: y
% Request aborted - Must first disable Load Balancing before enabling Assisted Roaming Prediction Optimization on this WLAN.

Examples

This example shows how to enable band select on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# band-select                            
Switch(config-wlan)# end

This example shows how to disable band selection on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# no band-select
Switch(config-wlan)# end

Examples

This example shows how to enable a broadcast SSID on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# broadcast-ssid                            
Switch(config-wlan)# end

This example shows how to disable a broadcast SSID on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# no broadcast-ssid
Switch(config-wlan)# end

Examples

This example shows how to enable VoIP on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# call-snoop                            
Switch(config-wlan)# end

This example shows how to disable VoIP on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# no call-snoop
Switch(config-wlan)# end

Examples

This example shows how to enable channel scan defer priority on a WLAN and set it to a priority value 4:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# channel-scan defer-priority 4                            
Switch(config-wlan)# end

This example shows how to disable channel scan defer priority on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# no channel-scan defer-priority 4
Switch(config-wlan)# end

Examples

This example shows how to enable a channel scan on the WLAN and set the scan deferral time to 300 milliseconds:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# channel-scan defer-time 300                            
Switch(config-wlan)# end

This example shows how to disable channel scan defer time on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# no channel-scan defer-time
Switch(config-wlan)# end

Examples

This example shows how to enable coverage hole detection on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# chd                            
Switch(config-wlan)# end

This example shows how to disable coverage hole detection on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# no chd
Switch(config-wlan)# end

Examples

This example shows how to configure a client association limit on a WLAN and configure the client limit to 200:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# shutdown
Switch(config-wlan)# client association limit 200                            
Switch(config-wlan)# no shutdown
Switch(config-wlan)# end

This example shows how to disable a client association limit on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# shutdown
Switch(config-wlan)# no client association limit
Switch(config-wlan)# no shutdown
Switch(config-wlan)# end

Switch# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# client association limit radio 200
Switch(config-wlan)# no shutdown
Switch(config-wlan)# end

Switch# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# client association limit ap 300
Switch(config-wlan)# no shutdown
Switch(config-wlan)# end

Examples

This example shows how to enable a client VLAN on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# client vlan client-vlan1                            
Switch(config-wlan)# end

This example shows how to disable a client association limit on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# no client vlan
Switch(config-wlan)# end

Examples

This example shows how to enable an Aironet IE for a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# ccx aironet-iesupport                            
Switch(config-wlan)# end

This example shows how to disable an Aironet IE on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# no ccx aironet-iesupport
Switch(config-wlan)# end

Examples

This example shows how to enable NetFlow monitoring on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# datalink flow monitor test output                            
Switch(config-wlan)# end

This example shows how to disable NetFlow monitoring on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# no datalink flow monitor test output
Switch(config-wlan)# end

Examples

This example shows how to set the Cisco Client Extension parameter to its default value:

Switch(config-wlan)# default ccx aironet-iesupport

Examples

This example shows how to enable the DTIM period on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# dtim dot11 24ghz 3

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# no dtim dot11 24ghz 3

Examples

This example shows how to configure a client exclusion list for a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# exclusionlist timeout 345

This example shows how to disable a client exclusion list on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# no exclusionlist timeout 345

Examples

This example shows how to exit the WLAN configuration submode:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# exit
Switch(config)# 

Examples

This example shows how to exit the WLAN AP group submode:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# ap group test
Switch(config-apgroup)# exit

Examples

This example shows how to configure a WLAN ACL:

Switch#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#wlan wlan1
Switch(config-wlan)#ip access-group test-acl

This example shows how to configure an IPv4 WLAN web ACL:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# ip access-group web test
Switch(config-wlan)# 

Examples

This example shows how to configure an IP flow monitor for the ingress traffic:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# ip flow monitor test input

This example shows how to disable an IP flow monitor:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# no ip flow monitor test input

Examples

This example shows how to enable IPSG:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# ip verify source mac-check

This example shows how to disable IPSG:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# no ip verify source mac-check

Examples

This example shows how to enable load balancing on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# shutdown
Switch(config)# wlan wlan1
Switch(config-wlan)# load-balance
Switch(config)# no shutdown
Switch(config-wlan)# end

This example shows how to disable load balancing on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# shutdown
Switch(config)# wlan wlan1
Switch(config-wlan)# no load-balance
Switch(config)# no shutdown
Switch(config-wlan)# end

Examples

This example shows how to enable the sticky mobility anchor:

Switch(config-wlan)# mobility anchor sticky
 

Examples

Switch (config-wlan)# mobility anchor <ip>

Examples

This example shows how to configure RADIUS NAC on the WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# aaa-override
Switch(config-wlan)# nac

This example shows how to disable RADIUS NAC on the WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# no nac
Switch(config-wlan)# no aaa-override

Examples

This show how to enable the passive client feature on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wireless multicast
Switch(config)# wlan test-wlan
Switch(config-wlan)# passive-client

This example shows how to disable the passive client feature on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wireless multicast
Switch(config)# wlan test-wlan
Switch(config-wlan)# no passive-client

Examples

This example shows how to enable the drop and forward-upstream options for peer-to-peer blocking:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# peer-blocking drop
Switch(config-wlan)# peer-blocking forward-upstream

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# no peer-blocking drop
Switch(config-wlan)# no peer-blocking forward-upstream

Examples

This example shows how to configure the WLAN on all radio bands:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# radio all

This example shows how to disable all radio bands on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# no radio all

Examples

This example shows how to enable the radio policy on the 802.11b band for an AP group:

Switch(config)# ap group test
Switch(config-apgroup)# wlan test-wlan
Switch(config-wlan-apgroup)# radio-policy dot11b

This example shows how to disable the radio policy on the 802.11b band of an AP group:

Switch(config)# ap group test
Switch(config-apgroup)# wlan test-wlan
Switch(config-wlan-apgroup)# no radio-policy dot11bg

Examples

This example shows how to enable the roamed voice client re-anchor feature:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# roamed-voice-client re-anchor

This example shows how to disable the roamed voice client re-anchor feature:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# no roamed-voice-client re-anchor

Examples

The following example configures security FT configuration for an open WLAN:

Switch#wlan test
Switch(config-wlan)# client vlan 0140
Switch(config-wlan)# no mobility anchor sticky
Switch(config-wlan)# no security wpa
Switch(config-wlan)# no security wpa akm dot1x
Switch(config-wlan)# no security wpa wpa2
Switch(config-wlan)# no security wpa wpa2 ciphers aes
Switch(config-wlan)# security ft
Switch(config-wlan)# shutdown

The following example shows a sample security FT on a WPA-enabled WLAN:

Switch# wlan test
Switch(config-wlan)# client vlan 0140
Switch(config-wlan)# no security wpa akm dot1x
Switch(config-wlan)# security wpa akm ft psk
Switch(config-wlan)# security wpa akm psk set-key ascii 0 test-test
Switch(config-wlan)# security ft
Switch(config-wlan)# no shutdown

Examples

This example shows how to enable the association comeback value at 15 seconds.

Switch(config-wlan)# security pmf association-comeback 15

This example shows how to configure mandatory 802.11w MPF protection for clients on a WLAN:

Switch(config-wlan)# security pmf mandatory

This example shows how to configure optional 802.11w MPF protection for clients on a WLAN:

Switch(config-wlan)# security pmf optional

This example shows how to configure the saquery parameter:

Switch(config-wlan)# security pmf saquery-retry-time 100

This example shows how to disable the PMF feature:

Switch(config-wlan)# no security pmf

Examples

The following example shows how to configure the authentication-list web authentication on a WLAN:

Switch(config-wlan)# security web-auth authentication-list test

Examples

The following example shows how to configure CCKM on the WLAN.

Switch(config-wlan)#security wpa akm cckm

Examples

This example shows how to configure the input QoS service policy on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# service-policy input policy-test 

This example shows how to disable the input QoS service policy on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# no service-policy input policy-test

This example shows how to configure the output QoS service policy on a WLAN to platinum (precious metal policy):

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# service-policy output platinum

Examples

This example shows how to configure a session timeout to 300 seconds:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# session-timeout 300

This example shows how to disable a session timeout:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# no session-timeout

Examples

This example shows how to display a summary of the WLANs configured on the device:

Switch# show wlan summary
Number of WLANs: 1

WLAN Profile Name                     SSID                           VLAN Status
--------------------------------------------------------------------------------
45   test-wlan                        test-wlan-ssid                  1    UP

This example shows how to display a summary of parameters configured on a particular WLAN:

Switch# show wlan name test-wlan
WLAN Identifier                                : 45
Profile Name                                   : test-wlan
Network Name (SSID)                            : test-wlan-ssid
Status                                         : Enabled
Broadcast SSID                                 : Enabled
Maximum number of Associated Clients           : 0
AAA Policy Override                            : Disabled
Network Admission Control
  NAC-State                                    : Disabled
Number of Active Clients                       : 0
Exclusionlist Timeout                          : 60
Session Timeout                                : 1800 seconds
CHD per WLAN                                   : Enabled
Webauth DHCP exclusion                         : Disabled
Interface                                      : default
Interface Status                               : Up
Multicast Interface                            : test
WLAN IPv4 ACL                                  : test
WLAN IPv6 ACL                                  : unconfigured
DHCP Server                                    : Default
DHCP Address Assignment Required               : Disabled
DHCP Option 82                                 : Disabled
DHCP Option 82 Format                          : ap-mac
DHCP Option 82 Ascii Mode                      : Disabled
DHCP Option 82 Rid Mode                        : Disabled
QoS Service Policy - Input
  Policy Name                                  : unknown
  Policy State                                 : None
QoS Service Policy - Output
  Policy Name                                  : unknown
  Policy State                                 : None
QoS Client Service Policy
  Input  Policy Name                           : unknown
  Output Policy Name                           : unknown
WifiDirect                                     : Disabled
WMM                                            : Disabled
Channel Scan Defer Priority:
  Priority (default)                           : 4
  Priority (default)                           : 5
  Priority (default)                           : 6
Scan Defer Time (msecs)                        : 100
Media Stream Multicast-direct                  : Disabled
CCX - AironetIe Support                        : Enabled
CCX - Gratuitous ProbeResponse (GPR)           : Disabled
CCX - Diagnostics Channel Capability           : Disabled
Dot11-Phone Mode (7920)                        : Invalid
Wired Protocol                                 : None
Peer-to-Peer Blocking Action                   : Disabled
Radio Policy                                   : All
DTIM period for 802.11a radio                  : 1
DTIM period for 802.11b radio                  : 1
Local EAP Authentication                       : Disabled
Mac Filter Authorization list name             : Disabled
Accounting list name                           : Disabled
802.1x authentication list name                : Disabled
Security
    802.11 Authentication                      : Open System
    Static WEP Keys                            : Disabled
    802.1X                                     : Disabled
    Wi-Fi Protected Access (WPA/WPA2)          : Enabled
        WPA (SSN IE)                           : Disabled
        WPA2 (RSN IE)                          : Enabled
            TKIP Cipher                        : Disabled
            AES Cipher                         : Enabled
        Auth Key Management
            802.1x                             : Enabled
            PSK                                : Disabled
            CCKM                               : Disabled
    IP Security                                : Disabled
    IP Security Passthru                       : Disabled
    L2TP                                       : Disabled
    Web Based Authentication                   : Disabled
    Conditional Web Redirect                   : Disabled
    Splash-Page Web Redirect                   : Disabled
    Auto Anchor                                : Disabled
    Sticky Anchoring                           : Enabled
    Cranite Passthru                           : Disabled
    Fortress Passthru                          : Disabled
    PPTP                                       : Disabled
    Infrastructure MFP protection              : Enabled
    Client MFP                                 : Optional
    Webauth On-mac-filter Failure              : Disabled
    Webauth Authentication List Name           : Disabled
    Webauth Parameter Map                      : Disabled
    Tkip MIC Countermeasure Hold-down Timer    : 60
Call Snooping                                  : Disabled
Passive Client                                 : Disabled
Non Cisco WGB                                  : Disabled
Band Select                                    : Disabled
Load Balancing                                 : Disabled
IP Source Guard                                : Disabled
Netflow Monitor                                : test
        Direction                              : Input
        Traffic                                : Datalink

Mobility Anchor List
IP Address
-----------

Examples

This example shows how to disable a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan test-wlan
Switch(config-wlan)# shutdown
Switch(config-wlan)# end
Switch# show wlan summary
Number of WLANs: 1

WLAN Profile Name                     SSID                           VLAN Status
--------------------------------------------------------------------------------
45   test-wlan                         test-wlan-ssid                  1    DOWN

This example shows how to enable a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan test-wlan
Switch(config-wlan)# no shutdown
Switch(config-wlan)# end
Switch# show wlan summary
Number of WLANs: 1

WLAN Profile Name                     SSID                           VLAN Status
--------------------------------------------------------------------------------
45   test-wlan                         test-wlan-ssid                  1    UP

Examples

This example shows how to enable a client disassociation and 486 busy message on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# sip-cac disassoc-client
Switch(config-wlan)# sip-cac send-486busy

This example shows how to disable a client association and 486 busy message on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# no sip-cac disassoc-client
Switch(config-wlan)# no sip-cac send-486busy

Examples

This example shows how to enable static-IP tunneling:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# static-ip tunneling

This example shows how to disable static-IP tunneling:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# no static-ip tunneling

Examples

This example shows how to configure a VLAN on an AP group:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# ap group ap-group-1
Switch(config-apgroup)# wlan test-wlan
Switch(config-wlan-apgroup)# vlan 3

Examples

This example shows how to enable non-Cisco WGBs on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# shutdown
Switch(config-wlan)# wgb non-cisco
Switch(config-wlan)# no shutdown

This example shows how to disable support for non-Cisco WGB clients on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# shutdown
Switch(config-wlan)# no wgb non-cisco
Switch(config-wlan)# no shutdown

Examples

The following example shows how to enable Wi-Fi Direct and configure the Wi-Fi Direct clients to associate with the WLAN:

Switch(config-wlan)# wifidirect policy permit

Examples

This example shows how to configure WLAN related parameters in the AP group configuration mode:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# ap group test
Switch(config-apgroup)# wlan qos-wlan

Examples

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config)# wlan test-wlan-cr 67 test-wlan-cr-ssid 

This example shows how to delete a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config)# no wlan test-wlan-cr 67 test-wlan-cr-ssid

Examples

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# shutdown

Examples

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# wmm allowed

This example shows how to disable WMM on a WLAN:

Switch# configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)# wlan wlan1
Switch(config-wlan)# no wmm