Configuring SmartPort Macros

This chapter describes how to configure and apply SmartPort macros on your switch.

Note For complete syntax and usage information for the switch commands used in this chapter, first look at the Cisco Catalyst 4500 Series Switch Command Reference and related publications at this location:

http://www.cisco.com/en/US/products//hw/switches/ps4324/index.html

If the command is not found in the Catalyst 4500 Command Reference, it will be found in the larger Cisco IOS library. Refer to the Catalyst 4500 Series Switch Cisco IOS Command Reference and related publications at this location:

http://www.cisco.com/en/US/products/ps6350/index.html

This chapter consists of these sections:

•Understanding SmartPort Macros

•Configuring Smart-Port Macros

•Displaying SmartPort Macros

Understanding SmartPort Macros

SmartPort macros provide a convenient way to save and share common configurations. You can use SmartPort macros to enable features and settings based on the location of a switch in the network and for mass configuration deployments across the network.

Each SmartPort macro is a set of CLI commands that you define. SmartPort macro sets do not contain new CLI commands; Each SmartPort macro is a group of existing CLI commands.

When you apply a SmartPort macro on an interface, the CLI commands contained within the macro are configured on the interface. When the macro is applied to an interface, the existing interface configurations are not lost. The new commands are added to interface and are saved in the running configuration file.

Configuring Smart-Port Macros

You can create a new SmartPort macro or use an existing macro as a template to create a new macro that is specific to your application. After you create the macro, you can apply it to an interface or a range of interfaces.

This section includes information about these topics:

•Default SmartPort Macro Configuration

•SmartPort Macro Configuration Guidelines

•Creating and Applying SmartPort Macros

Default SmartPort Macro Configuration

This section illustrates the default configurations for the four supported macros. These macros can only be viewed and applied; they cannot be modified by the user.

•cisco-desktop

•cisco-phone

•cisco-switch

•cisco-router

cisco-desktop 

# Basic interface - Enable data VLAN only

# Recommended value for access vlan (AVID) should not be 1

switchport access vlan $AVID

switchport mode access

# Enable port security limiting port to a single

# MAC address -- that of desktop

switchport port-security

# Ensure port-security age is greater than one minute

# and use inactivity timer

# "Port-security maximum 1" is the default and will not

# Show up in the config

switchport port-security violation restrict

switchport port-security aging time 2

switchport port-security aging type inactivity

# Configure port as an edge network port

spanning-tree portfast

spanning-tree bpduguard enable

cisco-phone 

# VoIP enabled interface - Enable data VLAN

# and voice VLAN (VVID)

# Recommended value for access vlan (AVID) should not be 1\

switchport access vlan $AVID

switchport mode access

# Update the Voice VLAN (VVID) value which should be

# different from data VLAN 

# Recommended value for voice vlan (VVID) should not be 1

switchport voice vlan $VVID

# Enable port security limiting port to a 3 MAC

# addressess -- One for desktop and two for phone

switchport port-security

switchport port-security maximum 3

# Ensure port-security age is greater than one minute

# and use inactivity timer

switchport port-security violation restrict

switchport port-security aging time 2

switchport port-security aging type inactivity

# Enable auto-qos to extend trust to attached Cisco phone

auto qos voip cisco-phone

# Configure port as an edge network port

spanning-tree portfast

spanning-tree bpduguard enable@

cisco-switch 

# Access Uplink to Distribution

switchport trunk encapsulation dot1q

# Define unique Native VLAN on trunk ports

# Recommended value for native vlan (NVID) should not be 1

switchport trunk native vlan $NVID

# Update the allowed VLAN range (VRANGE) such that it

# includes data, voice and native VLANs

# switchport trunk allowed vlan $VRANGE

# Hardcode trunk and disable negotiation to

# speed up convergence

switchport mode trunk

switchport nonegotiate

# Configure qos to trust this interface

auto qos voip trust

# 802.1w defines the link as pt-pt for rapid convergence

spanning-tree link-type point-to-point

cisco-router 

# Access Uplink to Distribution

switchport trunk encapsulation dot1q 

# Define unique Native VLAN on trunk ports

# Recommended value for native vlan (NVID) should not be 1

switchport trunk native vlan $NVID

# Update the allowed VLAN range (VRANGE) such that it

# includes data, voice and native VLANs

# switchport trunk allowed vlan $VRANGE

# Hardcode trunk and disable negotiation to

# speed up convergence

# Hardcode speed and duplex to router

switchport mode trunk

switchport nonegotiate

speed 100

duplex full 

# Configure qos to trust this interface

auto qos voip trust

qos trust dscp

# Ensure fast access to the network when enabling the interface.

# Ensure that switch devices cannot become active on the interface.

spanning-tree portfast

spanning-tree bpduguard enable

SmartPort Macro Configuration Guidelines

Follow these guidelines when configuring macros on your switch:

•Do not use exit or end commands when creating a macro. This action could cause commands that follow exit or end to execute in a different command mode.

•When creating a macro, all CLI commands should be interface configuration mode commands.

•Some CLI commands are specific to certain interface types. The macro will fail the syntax check or the configuration check, and the switch will return an error message if it is applied to an interface that does not accept the configuration.

•When a macro is applied to an interface, all existing configuration on the interface is retained. This is helpful when applying an incremental configuration to an interface.

•If you modify a macro definition by adding or deleting commands, the changes are not reflected on the interface where the original macro was applied. You need to reapply the updated macro on the interface to apply the new or changed commands.

•You can use the macro trace macro-name interface configuration command to show what macros are running on an interface or to debug the macro to determine any syntax or configuration errors.

•If a command fails when you apply a macro, either due to a syntax error or to a configuration error, the macro continues to apply the remaining commands to the interface.

•Applying a macro to an interface range is the same as applying a macro to a single interface. When you use an interface range, the macro is applied sequentially to each individual interface within the range. If a macro command fails on one interface, it is still applied to the remaining interfaces.

Creating and Applying SmartPort Macros

To create and apply a SmartPort macro, perform the following task:

 
Command
Purpose

Step 1  

Switch # configure terminal

Enters global configuration mode.

Step 2  

Switch(config)# macro name 
macro-name

Creates a macro definition, and enters a macro name. A macro definition can contain up to 3000 characters.

Enters the macro commands with one command per line. Use the @ character to end the macro. Use the # character at the beginning of a line to enter comment text within the macro.

Do not use the exit or end commands in a macro. This action could cause any commands following exit or end to execute in a different command mode. For best results, all commands in a macro should be interface configuration mode commands.

Step 3  

Switch(config)# interface interface-id

Enters interface configuration mode and specifies the interface on which to apply the macro.

Step 4  

Switch(config-if)# macro {apply | 
trace} macro-name

Applies each command defined in the macro to the interface.

Step 5  

Switch(config-if)# macro description 
text

(Optional) Enters a description about the macro that is applied to the interface.

Step 6  

Switch(config-if)# end

Returns to privileged EXEC mode.

Step 7  

Switch# show parser macro

Verifies that the macro was created.

Step 8  

Switch# show running-config 
interface interface-id

Verifies that the macro is applied to an interface.

Step 9  

Switch# copy running-config 
startup-config

(Optional) Saves your entries in the configuration file.

The no form of the macro name global configuration command only deletes the macro definition. It does not affect the configuration of those interfaces on which the macro is already applied. You can delete a macro-applied configuration on an interface by entering the default interface interface-id interface configuration command. Alternatively, you can create an anti-macro for an existing macro that contains the no form of all the corresponding commands in the original macro. Then apply the anti-macro to the interface.

The following sections illustrate how to apply and display the attachments on each of the supported macros:

•cisco-desktop

•cisco-phone

•cisco-switch

•cisco-router

cisco-desktop

This example shows how to apply the cisco-desktop macro to interface Fast Ethernet interface 2/9: 

Switch(config)# interface fastethernet2/9

Switch(config-if)# macro apply cisco-desktop $AVID 35

Switch(config-if)# end

Switch# show parser macro name cisco-desktop

Macro name : cisco-desktop

Macro type : customizable


# Basic interface - Enable data VLAN only

# Recommended value for access vlan (AVID) should not be 1

switchport access vlan $AVID [access_vlan_id]

switchport mode access

# Enable port security limiting port to a single

# MAC address -- that of desktop

switchport port-security

# Ensure port-security age is greater than one minute

# and use inactivity timer

# "Port-security maximum 1" is the default and will not

# Show up in the config

switchport port-security violation restrict

switchport port-security aging time 2

switchport port-security aging type inactivity

# Configure port as an edge network port

spanning-tree portfast

spanning-tree bpduguard enable


Switch# show parser macro description 

Interface    Macro Description

--------------------------------------------------------------

Fa2/9        cisco-desktop

--------------------------------------------------------------

cisco-phone

This example shows how to apply the cisco-phone macro to interface Fast Ethernet interface 2/9: 

Switch(config)# interface fastethernet2/9

Switch(config-if)# macro apply cisco-phone

Switch(config-if)# macro description cisco-phone $AVID 35 $VVID 56

Switch(config-if)# end

Switch# show parser macro name cisco-phone

Macro name : cisco-phone

Macro type : customizable


# VoIP enabled interface - Enable data VLAN

# and voice VLAN (VVID)

# Recommended value for access vlan (AVID) should not be 1\

switchport access vlan $AVID [access_vlan_id]

switchport mode access

# Update the Voice VLAN (VVID) value which should be

# different from data VLAN 

# Recommended value for voice vlan (VVID) should not be 1

switchport voice vlan $VVID [voice_vlan_id]

# Enable port security limiting port to a 3 MAC

# addressess -- One for desktop and two for phone

switchport port-security

switchport port-security maximum 3

# Ensure port-security age is greater than one minute

# and use inactivity timer

switchport port-security violation restrict

switchport port-security aging time 2

switchport port-security aging type inactivity

# Enable auto-qos to extend trust to attached Cisco phone

auto qos voip cisco-phone

# Configure port as an edge network port

spanning-tree portfast

spanning-tree bpduguard enable@


Switch# show parser macro description 

Interface    Macro Description

--------------------------------------------------------------

Fa2/9        cisco-phone

--------------------------------------------------------------

cisco-switch

This example shows how to apply the cisco-switch macro to interface Fast Ethernet interface 2/9: 

Switch(config)# interface fastethernet2/9

Switch(config-if)# macro apply cisco-switch

Switch(config-if)# macro description cisco-switch $NVID 38

Switch(config-if)# end

Switch# show parser macro name cisco-switch

Macro name : cisco-switch

Macro type : customizable


# Access Uplink to Distribution

switchport trunk encapsulation dot1q

# Define unique Native VLAN on trunk ports

# Recommended value for native vlan (NVID) should not be 1

switchport trunk native vlan $NVID [native_vlan_id]

# Update the allowed VLAN range (VRANGE) such that it

# includes data, voice and native VLANs

# switchport trunk allowed vlan $VRANGE [vlan_range]

# Hardcode trunk and disable negotiation to

# speed up convergence

switchport mode trunk

switchport nonegotiate

# Configure qos to trust this interface

auto qos voip trust

# 802.1w defines the link as pt-pt for rapid convergence

spanning-tree link-type point-to-point


Switch# show parser macro description 

Interface    Macro Description

--------------------------------------------------------------

Fa2/9        cisco-switch

--------------------------------------------------------------

cisco-router

This example shows how to apply the cisco-router macro to interface Fast Ethernet interface 2/9: 

Switch(config)# interface fastethernet2/9

Switch(config-if)# macro apply cisco-router

Switch(config-if)# macro description cisco-router $NVID 45I

Switch(config-if)# end

Switch# show parser macro name cisco-router

Macro name : cisco-router

Macro type : customizable


# Access Uplink to Distribution

switchport trunk encapsulation dot1q 

# Define unique Native VLAN on trunk ports

# Recommended value for native vlan (NVID) should not be 1

switchport trunk native vlan $NVID [native_vlan_id]

# Update the allowed VLAN range (VRANGE) such that it

# includes data, voice and native VLANs

# switchport trunk allowed vlan $VRANGE [vlan_range]

# Hardcode trunk and disable negotiation to

# speed up convergence

# Hardcode speed and duplex to router

switchport mode trunk

switchport nonegotiate

speed 100

duplex full 

# Configure qos to trust this interface

auto qos voip trust

qos trust dscp

# Ensure fast access to the network when enabling the interface.

# Ensure that switch devices cannot become active on the interface.

spanning-tree portfast

spanning-tree bpduguard enable 


Switch# show parser macro description 

Interface    Macro Description

--------------------------------------------------------------

Fa2/9        cisco-router

--------------------------------------------------------------

Displaying SmartPort Macros

To display the SmartPort macros, use one or more of the privileged EXEC commands in Table 38-1.

Table 38-1 Commands for Displaying SmartPort Macros 

Command
Purpose

show parser macro

Displays all configured macros.

show parser macro name macro-name

Displays a specific macro.

show parser macro brief

Displays the configured macro names.

show parser macro description [interface interface-id]

Displays the macro description for all interfaces or for a specified interface.