Catalyst 4500 Series Switch SW Configuration Guide, Release IOS-XE 3.2.xSG

Configuring Y.1731 (AIS and RDI)

The Catalyst 4500 series switch supports Y.1731 Ethernet Alarm Indication Signal function (ETH-AIS) and Ethernet Remote Defect Indication function (ETH-RDI) to provide fault and performance management for service providers in large networks. This chapter describes how to configure Y.1731 ETH-AIS and ETH-RDI.

Note For complete command and configuration information for Y.1731, see the Cisco IOS feature module at this URL:

http://www.cisco.com/en/US/docs/ios-xml/ios/cether/configuration/12-2sr/ce-cfm-y1731.html

This chapter contains these sections:

•Definition List

•Y.1731 Overview

•Configuring Y.1731

•Displaying Y.1731 Information

Definition List

Y.1731 Overview

These sections contain conceptual information about Y.1731:

•Background

•Alarm Indication Signal

•Ethernet Remote Defect Indication

Background

The advent of Ethernet as a metropolitan and WAN technology imposes a new set of Operations, Administration, and Maintenance (OAM) requirements on Ethernet's traditionally Enterprise-oriented functions. The expansion of this technology into the larger and more complex wider user base makes operational management of link uptime crucial. Isolating and responding to failures quickly directly affects the competitiveness of the Service Provider.

Server MEP

A Server MEP is a compound function of the Server layer termination function and the Server/ETH adaptation function. It issues frames with ETH-AIS information upon detecting a defect at the Server layer by the Server layer termination function or the adaptation function.

A Virtual MEP represents the logical termination point of CFM MAs defined at the link or transport layer. Imagine a server MEP as one running or defined at Maintenance Level -1. For example, you could associate an outward facing Server MEP with each termination point of IEEE 802.3ah OAM, or with each termination point of MPLS PW OAM.

Alarm Indication Signal

ETH-AIS enables you to suppress alarms when defects are detected at the server (sub) layer. Because of STP's ability to restore, you would not expect to apply ETH-AIS in the STP environments. For the Catalyst 4500 Metro switch, an administrator can enable and disable AIS in the STP environment.

You can enable or disable transmission of frames with ETH-AIS information on an MEP (or on a Server MEP).

Moreover, you can issue frames with ETH-AIS information at the client Maintenance Level by a MEP, including a Server MEP upon detecting defect conditions.

The defect conditions may include:

•Signal fail conditions with ETH-CC enabled

•AIS condition with ETH-CC disabled

For multipoint ETH connectivity, a MEP cannot determine the specific server (sub) layer entity that has encountered defect conditions upon receiving a frame with ETH-AIS information. More importantly, it cannot determine the associated subset of its peer MEPs for which it should suppress alarms because the received ETH-AIS information does not contain that information. Therefore, when a MEP receives a frame with ETH-AIS information, it suppresses alarms for all peer MEPs whether there is still connectivity or not.

For a point-to-point ETH connection, however, a MEP has only one peer MEP. Therefore, there is no ambiguity regarding the peer MEP for which it should suppress alarms when it receives the ETH-AIS information.

Only a MEP, including a Server MEP, is configured to issue frames with ETH-AIS information. Once the MEP detects a defect condition, it immediately starts transmitting periodic frames with ETH-AIS information at a configured client maintenance level. We send the AIS frames at a configured MIP level for an interface. A MEP continues to transmit periodic frames with ETH-AIS information until the defect condition is removed. Upon receiving a frame with ETH-AIS information a MEP detects AIS condition and suppresses loss of continuity alarms associated with all its peer MEPs. A MEP resumes loss of continuity alarm generation upon detecting loss of continuity defect conditions in the absence of AIS condition.

Ethernet Remote Defect Indication

A MEP can use ETH-RDI to notify its peer MEPs that it detects a defect condition. ETH-RDI is used only when ETH-CC transmission is enabled.

ETH-RDI has the following two applications:

•Single-ended fault management: The receiving MEP detects an RDI defect condition, which is correlated with other defect conditions in this MEP and may cause a fault. The absence of received ETH-RDI information in a single MEP indicates the absence of defects in the entire maintenance.

•Contribution to far-end performance monitoring: It reflects a defect condition in the far-end which serves as input to the performance monitoring process.

A MEP that is in a defect condition transmits frames with ETH-RDI information. A MEP, upon receiving frames with ETH-RDI information, determines that its peer MEP has encountered a defect condition. For multipoint ETH connectivity, however, a MEP, upon receiving frames with ETH-RDI information, cannot determine the associated subset of its peer MEPs with which the MEP transmitting RDI information encounters defect conditions. This is because the transmitting MEP itself does not always have that information.

Figure 47-1 Generating and Propagating AIS Messages Upon a Defect (Link Fail)

Configuring Y.1731

Note Y.1731 is enabled by default.

These sections are included:

•Y.1731 Configuration Guidelines

•Configuring AIS Parameters

•Clearing MEP from the AIS Defect Condition

•Clearing SMEP from the AIS Defect Condition

Y.1731 Configuration Guidelines

Configuration guidelines and restrictions for Y.1731 include the following:

•Because of STP's restoration capability, do not expect ETH-AIS to be applied in the STP environments.

•AIS is enabled by default on a CFM maintenance domain. The following section illustrates the commands you can use to disable AIS on a maintenance domain. Likewise, RDI is a flag bit in the CC message. Provided CC transmission is enabled, the present RDI flag of the CC message is set to true or false.

Configuring AIS Parameters

To set the parameters for AIS, follow these steps:

Switch# configure terminal

Switch (config)# ethernet cfm ais domain name 
vlan range

Switch(config-ais-mep-cfm)# disable

Switch(config-ais-mep-cfm)# period period

Switch(config-ais-mep-cfm)# level level

Switch(config-ais-mep-cfm)# expiry-threshold 
threshold

Switch(config-ais-mep-cfm)# express alarm

Switch(config-ais-mep-cfm)# exit

Switch(config)# [no] ethernet cfm ais  
link-status global

Switch(config-if)# [no] ethernet cfm ais 
link-status period period

Switch(config-if)# [no] ethernet cfm ais 
link-status level level

end

Switch# show ethernet cfm smep interface name

Switch# show ethernet cfm maintenance-points 
local detail

Switch# show ethernet cfm maintenance-points 
remote detail

Switch# show ethernet cfm error

Switch# show running-config

Switch# copy running-config startup-config

Use the no versions of the commands to remove the configuration or return to the default configurations.

Clearing MEP from the AIS Defect Condition

To clear the MEP, enter one of the following commands:

Switch# clear ethernet cfm ais domain domain name mpid local mpid vlan vlan#

Switch# clear ethernet cfm ais domain domain name mpid local mpid evc evc_name

Clearing SMEP from the AIS Defect Condition

To clear the CSMP, enter one of the following commands:

Switch# clear ethernet cfm ais link-status interface interface_name

Switch# clear ethernet cfm error

Note This operation also clears all error conditions including AIS.

Displaying Y.1731 Information

This example shows how to track the RDI defect and to verify the configuration parameters:

Switch# show ethernet cfm main local detail

MEP Settings:

-------------

MPID: 1109

DomainName: PROVIDER_DOMAIN

Level: 4

Direction: I

EVC: evc_1

Interface: Gi3/1

CC-Status: Enabled

MAC: 001b.d550.91fd

Defect Condition: No Defect

presentRDI: FALSE (RDI defect is NOT present)

AIS-Status: Enabled

AIS Period: 60000(ms)

AIS Expiry Threshold: 3.5

Level to transmit AIS: Default

Suppress Alarm configuration: Enabled

Suppressing Alarms: No

MIP Settings:

-------------

Level Type  Port                      MAC

7     MIP   Gi3/1                     001b.d550.91fd

4     MIP   Te1/2                     001b.d550.91fd

Switch#

*Feb 18 05:40:35.659: %ETHER_CFM-6-ENTER_AIS: local mep with mpid 1109 level 4 id 100 dir 
I Interface GigabitEthernet3/1 enters AIS defect condition (gi3/2 enters AIS state)

Switch# show ethernet cfm main local detail

MEP Settings:

-------------

MPID: 1109

DomainName: PROVIDER_DOMAIN

Level: 4

Direction: I

EVC: evc_1

Interface: Gi3/1

CC-Status: Enabled

MAC: 001b.d550.91fd

Defect Condition: AIS

presentRDI: TRUE (RDI defect IS present)

AIS-Status: Enabled

AIS Period: 60000(ms)

AIS Expiry Threshold: 3.5

Level to transmit AIS: Default

Suppress Alarm configuration: Enabled

Suppressing Alarms: Yes

MIP Settings:

-------------

Level Type  Port                      MAC

7     MIP   Gi3/1                     001b.d550.91fd

4     MIP   Te1/2                     001b.d550.91fd

Switch# show ethernet cfm error

Level Vlan MPID Remote MAC     Reason               Service ID

4     100  2101 001d.4566.aa3d 0 lifetime TLV       customerX

4     100    -  001b.d550.91fd Receive AIS          customerX

Switch#

*Feb 18 05:51:08.567: %ETHER_CFM-6-EXIT_AIS: local mep with mpid 1109 level 4 id 100 dir I 
Interface GigabitEthernet3/1 exited AIS defect condition

(gi3/1 exits AIS state)

Switch# show ethernet cfm main local detail

MEP Settings:

-------------

MPID: 1109

DomainName: PROVIDER_DOMAIN

Level: 4

Direction: I

EVC: evc_1

Interface: Gi3/1

CC-Status: Enabled

MAC: 001b.d550.91fd

Defect Condition: No Defect

presentRDI: FALSE (RDI defect is not present anymore)

AIS-Status: Enabled

AIS Period: 60000(ms)

AIS Expiry Threshold: 3.5

Level to transmit AIS: Default

Suppress Alarm configuration: Enabled

Suppressing Alarms: No

MIP Settings:

-------------

Level Type  Port                      MAC

7     MIP   Gi3/1                     001b.d550.91fd

4     MIP   Te1/2                     001b.d550.91fd

Switch#

To display Y.1731 information, you can use the following commands (Table 47-1).

show ethernet cfm maintenance-point local 
detail

show ethernet cfm smep [interface <name>]

show ethernet cfm error

show ethernet cfm maintenance-points 
remote [detail