Examples
This example shows
how to display information about the redundancy facility:
Device# show redundancy
Redundant System Information :
------------------------------
Available system uptime = 1 hour, 25 minutes
Switchovers system experienced = 0
Standby failures = 0
Last switchover reason = not known
Hardware Mode = Duplex
Configured Redundancy Mode = SSO
Operating Redundancy Mode = SSO
Maintenance Mode = Disabled
Communications = Up
Current Processor Information :
------------------------------
Active Location = slot 1
Current Software state = ACTIVE
Uptime in current state = 1 hour, 25 minutes
Image Version = Cisco IOS Software, Catalyst L3 Switch Software
(CAT9K_LITE_IOSXE), Version 16.9.x
Copyright (c) 1986-2018 by Cisco Systems, Inc.
Compiled Sat 29-S
Configuration register = 0x102
Peer Processor Information :
----------------------------
Standby Location = slot 3
Current Software state = STANDBY HOT
Uptime in current state = 1 hour, 22 minutes
Image Version = Cisco IOS Software, Catalyst L3 Switch Software
(CAT9K_LITE_IOSXE), Version 16.9.x
Copyright (c) 1986-2018 by Cisco Systems, Inc.
Compiled Sat 29-S
Configuration register = 0x102
Device#
This example shows
how to display redundancy facility client information:
Device# show redundancy clients
Group ID = 1
clientID = 20002 clientSeq = 4 EICORE HA Client
clientID = 24100 clientSeq = 5 WCM_CAPWAP
clientID = 24101 clientSeq = 6 WCM RRM HA
clientID = 24103 clientSeq = 8 WCM QOS HA
clientID = 24105 clientSeq = 10 WCM_MOBILITY
clientID = 24106 clientSeq = 11 WCM_DOT1X
clientID = 24107 clientSeq = 12 WCM_APFROGUE
clientID = 24110 clientSeq = 15 WCM_CIDS
clientID = 24111 clientSeq = 16 WCM_NETFLOW
clientID = 24112 clientSeq = 17 WCM_MCAST
clientID = 24120 clientSeq = 18 wcm_comet
clientID = 24001 clientSeq = 21 Table Manager Client
clientID = 20010 clientSeq = 24 SNMP SA HA Client
clientID = 20007 clientSeq = 27 Installer HA Client
clientID = 29 clientSeq = 60 Redundancy Mode RF
clientID = 139 clientSeq = 61 IfIndex
clientID = 3300 clientSeq = 62 Persistent Variable
clientID = 25 clientSeq = 68 CHKPT RF
clientID = 20005 clientSeq = 74 IIF-shim
clientID = 10001 clientSeq = 82 QEMU Platform RF
<output truncated>
The output displays
the following information:
-
clientID
displays the client’s ID number.
-
clientSeq
displays the client’s notification sequence number.
-
Current
redundancy facility state.
This example shows
how to display the redundancy facility counter information:
Device# show redundancy counters
Redundancy Facility OMs
comm link up = 0
comm link down = 0
invalid client tx = 0
null tx by client = 0
tx failures = 0
tx msg length invalid = 0
client not rxing msgs = 0
rx peer msg routing errors = 0
null peer msg rx = 0
errored peer msg rx = 0
buffers tx = 0
tx buffers unavailable = 0
buffers rx = 0
buffer release errors = 0
duplicate client registers = 0
failed to register client = 0
Invalid client syncs = 0
Device#
This example shows
how to display redundancy facility history information:
Device# show redundancy history
00:00:00 *my state = INITIALIZATION(2) peer state = DISABLED(1)
00:00:00 RF_EVENT_INITIALIZATION(524) op=0 rc=0
00:00:00 *my state = NEGOTIATION(3) peer state = DISABLED(1)
00:00:01 client added: Table Manager Client(24001) seq=21
00:00:01 client added: SNMP SA HA Client(20010) seq=24
00:00:06 client added: WCM_CAPWAP(24100) seq=5
00:00:06 client added: WCM QOS HA(24103) seq=8
00:00:07 client added: WCM_DOT1X(24106) seq=11
00:00:07 client added: EICORE HA Client(20002) seq=4
00:00:09 client added: WCM_MOBILITY(24105) seq=10
00:00:09 client added: WCM_NETFLOW(24111) seq=16
00:00:09 client added: WCM_APFROGUE(24107) seq=12
00:00:09 client added: WCM RRM HA(24101) seq=6
00:00:09 client added: WCM_MCAST(24112) seq=17
00:00:09 client added: WCM_CIDS(24110) seq=15
00:00:09 client added: wcm_comet(24120) seq=18
00:00:22 RF_STATUS_REDUNDANCY_MODE_CHANGE(405) First Slave(0) op=0 rc=0
00:00:22 RF_STATUS_REDUNDANCY_MODE_CHANGE(405) Slave(6107) op=0 rc=0
00:00:22 RF_STATUS_REDUNDANCY_MODE_CHANGE(405) Slave(6109) op=0 rc=0
00:00:22 RF_STATUS_REDUNDANCY_MODE_CHANGE(405) Slave(6128) op=0 rc=0
00:00:22 RF_STATUS_REDUNDANCY_MODE_CHANGE(405) Slave(8897) op=0 rc=0
00:00:22 RF_STATUS_REDUNDANCY_MODE_CHANGE(405) Slave(8898) op=0 rc=0
00:00:22 RF_STATUS_REDUNDANCY_MODE_CHANGE(405) Slave(8901) op=0 rc=0
00:00:22 RF_EVENT_SLAVE_STATUS_DONE(523) First Slave(0) op=405 rc=0
00:00:22 RF_STATUS_REDUNDANCY_MODE_CHANGE(405) Redundancy Mode RF(29) op=0 rc=0
00:00:22 RF_STATUS_REDUNDANCY_MODE_CHANGE(405) IfIndex(139) op=0 rc=0
<output truncated>
This example shows how to display information about the redundancy facility subordinates:
Device# show redundancy slaves
Group ID = 1
Slave/Process ID = 6107 Slave Name = [installer]
Slave/Process ID = 6109 Slave Name = [eicored]
Slave/Process ID = 6128 Slave Name = [snmp_subagent]
Slave/Process ID = 8897 Slave Name = [wcm]
Slave/Process ID = 8898 Slave Name = [table_mgr]
Slave/Process ID = 8901 Slave Name = [iosd]
Device#
This example shows
how to display information about the redundancy facility state:
Device# show redundancy states
my state = 13 -ACTIVE
peer state = 1 -DISABLED
Mode = Simplex
Unit ID = 1
Redundancy Mode (Operational) = SSO
Redundancy Mode (Configured) = SSO
Redundancy State = Non Redundant
Manual Swact = disabled (system is simplex (no peer unit))
Communications = Down Reason: Simplex mode
client count = 75
client_notification_TMR = 360000 milliseconds
keep_alive TMR = 9000 milliseconds
keep_alive count = 0
keep_alive threshold = 18
RF debug mask = 0
Device#