IE 3000 Switch Debug Commands
This appendix describes the debug privileged EXEC commands that have been created or changed for use with the IE 3000 switch. These commands are helpful in diagnosing and resolving internetworking problems and should be enabled only under the guidance of Cisco technical support staff.
Caution
Because debugging output is assigned high priority in the CPU process, it can render the system unusable. For this reason, use the
debug commands only to troubleshoot specific problems or during troubleshooting sessions with Cisco technical support staff. It is best to use the
debug commands during periods of lower network traffic and fewer users. Debugging during these periods decreases the likelihood that increased
debug command processing overhead will affect system use.
debug auto qos
Use the debug auto qos privileged EXEC command to enable debugging of the automatic quality of service (auto-QoS) feature. Use the no form of this command to disable debugging.
debug auto qos
no debug auto qos
Syntax Description
This command has no keywords or arguments.
Defaults
Auto-QoS debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
To display the QoS configuration that is automatically generated when auto-QoS is enabled, enable debugging before you enable auto-QoS. You enable debugging by entering the debug auto qos privileged EXEC command.
The undebug auto qos command is the same as the no debug auto qos command.
Examples
This example shows how to display the QoS configuration that is automatically generated when auto-QoS is enabled:
Switch# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)# interface gigabitethernet1/1
Switch(config-if)# auto qos voip cisco-phone
21:29:41: mls qos map cos-dscp 0 8 16 26 32 46 48 56
21:29:42: no mls qos srr-queue input cos-map
21:29:42: no mls qos srr-queue output cos-map
21:29:42: mls qos srr-queue input cos-map queue 1 threshold 3 0
21:29:42: mls qos srr-queue input cos-map queue 1 threshold 2 1
21:29:42: mls qos srr-queue input cos-map queue 2 threshold 1 2
21:29:42: mls qos srr-queue input cos-map queue 2 threshold 2 4 6 7
21:29:43: mls qos srr-queue input cos-map queue 2 threshold 3 3 5
21:29:43: mls qos srr-queue output cos-map queue 1 threshold 3 5
21:29:43: mls qos srr-queue output cos-map queue 2 threshold 3 3 6 7
21:29:44: mls qos srr-queue output cos-map queue 3 threshold 3 2 4
21:29:44: mls qos srr-queue output cos-map queue 4 threshold 2 1
21:29:44: mls qos srr-queue output cos-map queue 4 threshold 3 0
21:29:44: no mls qos srr-queue input dscp-map
21:29:44: no mls qos srr-queue output dscp-map
21:29:44: mls qos srr-queue input dscp-map queue 1 threshold 2 9 10 11 12 13 14 15
21:29:45: mls qos srr-queue input dscp-map queue 1 threshold 3 0 1 2 3 4 5 6 7
21:29:45: mls qos srr-queue input dscp-map queue 1 threshold 3 32
21:29:45: mls qos srr-queue input dscp-map queue 2 threshold 1 16 17 18 19 20 21 22 23
21:29:45: mls qos srr-queue input dscp-map queue 2 threshold 2 33 34 35 36 37 38 39 48
21:29:46: mls qos srr-queue input dscp-map queue 2 threshold 2 49 50 51 52 53 54 55 56
21:29:46: mls qos srr-queue input dscp-map queue 2 threshold 2 57 58 59 60 61 62 63
21:29:46: mls qos srr-queue input dscp-map queue 2 threshold 3 24 25 26 27 28 29 30 31
21:29:47: mls qos srr-queue input dscp-map queue 2 threshold 3 40 41 42 43 44 45 46 47
21:29:47: mls qos srr-queue output dscp-map queue 1 threshold 3 40 41 42 43 44 45 46 47
21:29:47: mls qos srr-queue output dscp-map queue 2 threshold 3 24 25 26 27 28 29 30 31
21:29:47: mls qos srr-queue output dscp-map queue 2 threshold 3 48 49 50 51 52 53 54 55
21:29:48: mls qos srr-queue output dscp-map queue 2 threshold 3 56 57 58 59 60 61 62 63
21:29:48: mls qos srr-queue output dscp-map queue 3 threshold 3 16 17 18 19 20 21 22 23
21:29:48: mls qos srr-queue output dscp-map queue 3 threshold 3 32 33 34 35 36 37 38 39
21:29:49: mls qos srr-queue output dscp-map queue 4 threshold 1 8
21:29:49: mls qos srr-queue output dscp-map queue 4 threshold 2 9 10 11 12 13 14 15
21:29:49: mls qos srr-queue output dscp-map queue 4 threshold 3 0 1 2 3 4 5 6 7
21:29:49: no mls qos srr-queue input priority-queue 1
21:29:49: no mls qos srr-queue input priority-queue 2
21:29:50: mls qos srr-queue input bandwidth 90 10
21:29:50: no mls qos srr-queue input buffers
21:29:50: mls qos queue-set output 1 buffers 10 10 26 54
21:29:50: interface GigabitEthernet1/1
21:29:50: mls qos trust device cisco-phone
21:29:50: mls qos trust cos
21:29:50: srr-queue bandwidth shape 10 0 0 0
21:29:50: srr-queue bandwidth share 10 10 60 20
Related Commands
|
|
auto qos voip |
Configures auto-QoS for voice over IP (VoIP) within a QoS domain. |
show auto qos |
Displays the initial configuration that is generated by the automatic auto-QoS feature |
show debugging |
Displays information about the types of debugging that are enabled. |
debug backup
Use the debug backup privileged EXEC command to enable debugging of the Flex Links backup interface. Use the no form of this command to disable debugging.
debug backup {all | errors | events | vlan-load-balancing}
no debug backup {all | errors | events | vlan-load-balancing}
Syntax Description
all |
Display all backup interface debug messages. |
errors |
Display backup interface error or exception debug messages. |
events |
Display backup interface event debug messages. |
vlan-load- balancing |
Display backup interface VLAN load balancing. |
Defaults
Backup interface debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(37)SE |
Added vlan-load-balancing keyword. |
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug backup command is the same as the no debug backup command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
debug cip
Use the debug cip privileged EXEC command to enable debugging of the Common Industrial Protocol (CIP) subsystem. Use the no form of this command to disable debugging.
debug cip {assembly | connection manager | errors | event | file | io | packet | request response | security | session | socket}
no debug cip {assembly | connection manager | errors | event | file | io | packet | request response | security | session | socket}
Syntax Description
assembly |
Display CIP assembly debug messages. |
connection manager |
Display CIP connection manager debug messages. |
errors |
Display CIP error debug messages. |
event |
Display CIP event debug messages. |
file |
Display CIP file debug messages. |
io |
Display CIP input/output (I/O) debug messages. |
packet |
Display CIP packet debug messages. |
request response |
Display CIP request response debug messages. |
security |
Display CIP security debug messages. |
session |
Display CIP session debug messages. |
socket |
Display CIP socket debug messages. |
Defaults
CIP debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug cip command is the same as the no debug cip command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
show cip |
Displays information about the Common Industrial Protocol (CIP) subsystem. |
debug cluster
Use the debug cluster privileged EXEC command to enable debugging of cluster-specific events. Use the no form of this command to disable debugging.
debug cluster {discovery | events | extended | hsrp | http | ip [packet] | members | nat | neighbors | platform | snmp | vqpxy}
no debug cluster {discovery | events | extended | hsrp | http | ip [packet] | members | nat | neighbors | platform | snmp | vqpxy}
Syntax Description
discovery |
Display cluster discovery debug messages. |
events |
Display cluster event debug messages. |
extended |
Display extended discovery debug messages. |
hsrp |
Display the Hot Standby Router Protocol (HSRP) debug messages. |
http |
Display Hypertext Transfer Protocol (HTTP) debug messages. |
ip [packet] |
Display IP or transport packet debug messages. |
members |
Display cluster member debug messages. |
nat |
Display Network Address Translation (NAT) debug messages. |
neighbors |
Display cluster neighbor debug messages. |
platform |
Display platform-specific cluster debug messages. |
snmp |
Display Simple Network Management Protocol (SNMP) debug messages. |
vqpxy |
Display VLAN Query Protocol (VQP) proxy debug messages. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
This command is available only on the cluster command switch.
The undebug cluster command is the same as the no debug cluster command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
show cluster |
Displays the cluster status and a summary of the cluster to which the switch belongs. |
show cluster candidates |
Displays a list of candidate switches when entered on the command switch. |
show cluster members |
Displays information about cluster members when executed on the command switch. |
debug dot1x
Use the debug dot1x privileged EXEC command to enable debugging of the IEEE 802.1x authentication feature. Use the no form of this command to disable debugging.
debug dot1x {all | errors | events | feature | packets | registry | state-machine}
no debug dot1x {all | errors | events | feature | packets | registry | state-machine}
Syntax Description
all |
Display all IEEE 802.1x authentication debug messages. |
errors |
Display IEEE 802.1x error debug messages. |
events |
Display IEEE 802.1x event debug messages. |
feature |
Display IEEE 802.1x feature debug messages. |
packets |
Display IEEE 802.1x packet debug messages. |
registry |
Display IEEE 802.1x registry invocation debug messages. |
state-machine |
Display state-machine related-events debug messages. |
Note
Though visible in the command-line help strings, the redundancy keyword is not supported.
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug dot1x command is the same as the no debug dot1x command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
show dot1x |
Displays IEEE 802.1xstatistics, administrative status, and operational status for the switch or for the specified port. |
debug dtp
Use the debug dtp privileged EXEC command to enable debugging of the Dynamic Trunking Protocol (DTP) activity. Use the no form of this command to disable debugging.
debug dtp {aggregation | all | decision | events | oserrs | packets | queue | states | timers}
no debug dtp {aggregation | all | decision | events | oserrs | packets | queue | states | timers}
Syntax Description
aggregation |
Display DTP user-message aggregation debug messages. |
all |
Display all DTP debug messages. |
decision |
Display the DTP decision-table debug messages. |
events |
Display the DTP event debug messages. |
oserrs |
Display DTP operating system-related error debug messages. |
packets |
Display DTP packet-processing debug messages. |
queue |
Display DTP packet-queueing debug messages. |
states |
Display DTP state-transition debug messages. |
timers |
Display DTP timer-event debug messages. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug dtp command is the same as the no debug dtp command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
show dtp |
Displays DTP information for the switch or for a specified interface. |
debug eap
Use the debug eap privileged EXEC command to enable debugging of the Extensible Authentication Protocol (EAP) activity. Use the no form of this command to disable debugging.
debug dot1x {all | authenticator | errors | events | md5 | packets | peer | sm}
no debug dot1x {all | authenticator | errors | events | md5 | packets | peer | sm}
Syntax Description
all |
Display all EAP debug messages. |
authenticator |
Display authenticator debug messages. |
errors |
Display EAP error debug messages. |
events |
Display EAP event debug messages. |
md5 |
Display EAP-MD5 debug messages. |
packets |
Display EAP packet debug messages. |
peer |
Display EAP peer debug messages. |
sm |
Display EAP state-machine related-events debug messages. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug dot1x command is the same as the no debug dot1x command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
show eap |
Displays EAP registration and session information for the switch or for the specified port. |
debug etherchannel
Use the debug etherchannel privileged EXEC command to enable debugging of the EtherChannel/PAgP shim. This shim is the software module that is the interface between the Port Aggregation Protocol (PAgP) software module and the port manager software module. Use the no form of this command to disable debugging.
debug etherchannel [all | detail | error | event | idb]
no debug etherchannel [all | detail | error | event | idb]
Syntax Description
all |
(Optional) Display all EtherChannel debug messages. |
detail |
(Optional) Display detailed EtherChannel debug messages. |
error |
(Optional) Display EtherChannel error debug messages. |
event |
(Optional) Debug major EtherChannel event messages. |
idb |
(Optional) Display PAgP interface descriptor block debug messages. |
Note
Though visible in the command-line help strings, the linecard keyword is not supported.
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
If you do not specify a keyword, all debug messages appear.
The undebug etherchannel command is the same as the no debug etherchannel command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
show etherchannel |
Displays EtherChannel information for the channel. |
debug interface
Use the debug interface privileged EXEC command to enable debugging of interface-related activities. Use the no form of this command to disable debugging.
debug interface {interface-id | null interface-number | port-channel port-channel-number | vlan vlan-id}
no debug interface {interface-id | null interface-number | port-channel port-channel-number | vlan vlan-id}
Syntax Description
interface-id |
Display debug messages for the specified physical port, identified by type switch number/module number/ port, for example gigabitethernet 0/2. |
null interface-number |
Display debug messages for null interfaces. The interface-number is always 0. |
port-channel port-channel-number |
Display debug messages for the specified EtherChannel port-channel interface. The port-channel-number range is 1 to 6. |
vlan vlan-id |
Display debug messages for the specified VLAN. The vlan-id range is 1 to 4094. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
If you do not specify a keyword, all debug messages appear.
The undebug interface command is the same as the no debug interface command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
show etherchannel |
Displays EtherChannel information for the channel. |
debug ip dhcp snooping
Use the debug ip dhcp snooping privileged EXEC command to enable debugging of DHCP snooping. Use the no form of this command to disable debugging.
debug ip dhcp snooping {mac-address | agent | event | packet}
no debug ip dhcp snooping {mac-address | agent | event | packet}
Syntax Description
mac-address |
Display debug messages for a DHCP packet with the specified MAC address. |
agent |
Display debug messages for DHCP snooping agents. |
event |
Display debug messages for DHCP snooping events. |
packet |
Display debug messages for DHCP snooping. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug ip dhcp snooping command is the same as the no debug ip dhcp snooping command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
debug ip igmp filter
Use the debug ip igmp filter privileged EXEC command to enable debugging of Internet Group Management Protocol (IGMP) filter events. Use the no form of this command to disable debugging.
debug ip igmp filter
no debug ip igmp filter
Syntax Description
This command has no arguments or keywords.
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug ip igmp filter command is the same as the no debug ip igmp filter command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
debug ip igmp max-groups
Use the debug ip igmp max-groups privileged EXEC command to enable debugging of Internet Group Management Protocol (IGMP) maximum groups events. Use the no form of this command to disable debugging.
debug ip igmp max-groups
no debug ip igmp max-groups
Syntax Description
This command has no arguments or keywords.
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug ip igmp max-groups command is the same as the no debug ip igmp max-groups command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
debug ip igmp snooping
Use the debug igmp snooping privileged EXEC command to enable debugging of Internet Group Management Protocol (IGMP) snooping activity. Use the no form of this command to disable debugging.
debug ip igmp snooping [group | management | querier | router | timer]
no debug ip igmp snooping [group | management | querier | router | timer]
Syntax Description
group |
(Optional) Display IGMP snooping group activity debug messages. |
management |
(Optional) Display IGMP snooping management activity debug messages. |
querier |
(Optional) Display IGMP snooping querier debug messages. |
router |
(Optional) Display IGMP snooping router activity debug messages. |
timer |
(Optional) Display IGMP snooping timer event debug messages. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug ip igmp snooping command is the same as the no debug ip igmp snooping command.
Related Commands
|
|
debug platform ip igmp snooping |
Displays information about platform-dependent IGMP snooping activity. |
show debugging |
Displays information about the types of debugging that are enabled. |
debug lacp
Use the debug lacp privileged EXEC command to enable debugging of Link Aggregation Control Protocol (LACP) activity. Use the no form of this command to disable debugging.
debug lacp [all | event | fsm | misc | packet]
no debug lacp [all | event | fsm | misc | packet]
Syntax Description
all |
(Optional) Display all LACP debug messages. |
event |
(Optional) Display LACP event debug messages. |
fsm |
(Optional) Display LACP finite state-machine debug messages. |
misc |
(Optional) Display miscellaneous LACP debug messages. |
packet |
(Optional) Display LACP packet debug messages. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug lacp command is the same as the no debug lacp command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
show lacp |
Displays LACP channel-group information. |
debug mac-notification
Use the debug mac-notification privileged EXEC command to enable debugging of MAC notification events. Use the no form of this command to disable debugging.
debug mac-notification
no debug mac-notification
Syntax Description
This command has no arguments or keywords.
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug mac-notification command is the same as the no debug mac-notification command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
show mac address-table notification |
Displays the MAC address notification information for all interfaces or the specified interface. |
debug matm
Use the debug matm privileged EXEC command to enable debugging of platform-independent MAC address management. Use the no form of this command to disable debugging.
debug matm
no debug matm
Syntax Description
This command has no arguments or keywords.
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug matm command is the same as the no debug matm command.
Related Commands
|
|
debug platform matm |
Displays information about platform-dependent MAC address management. |
show debugging |
Displays information about the types of debugging that are enabled. |
debug matm move update
Use the debug matm move update privileged EXEC command to enable debugging of MAC address-table move update message processing.
debug matm move update
no debug matm move update
Syntax Description
This command has no arguments or keywords.
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(25)SED |
This command was introduced. |
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug matm move update command is the same as the no debug matm move update command.
Related Commands
debug monitor
Use the debug monitor privileged EXEC command to enable debugging of the Switched Port Analyzer (SPAN) feature. Use the no form of this command to disable debugging.
debug monitor {all | errors | idb-update | info | list | notifications | platform | requests | snmp}
no debug monitor {all | errors | idb-update | info | list | notifications | platform | requests | snmp}
Syntax Description
all |
Display all SPAN debug messages. |
errors |
Display detailed SPAN error debug messages. |
idb-update |
Display SPAN interface description block (IDB) update-trace debug messages. |
info |
Display SPAN informational-tracing debug messages. |
list |
Display SPAN port and VLAN-list tracing debug messages. |
notifications |
Display SPAN notification debug messages. |
platform |
Display SPAN platform-tracing debug messages. |
requests |
Display SPAN request debug messages. |
snmp |
Display SPAN and Simple Network Management Protocol (SNMP) tracing debug messages. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug monitor command is the same as the no debug monitor command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
show monitor |
Displays information about all SPAN and remote SPAN (RSPAN) sessions on the switch. |
debug mvrdbg
Use the debug mvrdbg privileged EXEC command to enable debugging of Multicast VLAN Registration (MVR). Use the no form of this command to disable debugging.
debug mvrdbg {all | events | igmpsn | management | ports}
no debug mvrdbg {all | events | igmpsn | management | ports}
Syntax Description
all |
Display all MVR activity debug messages. |
events |
Display MVR event-handling debug messages. |
igmpsn |
Display MVR Internet Group Management Protocol (IGMP) snooping-activity debug messages. |
management |
Display MVR management-activity debug messages. |
ports |
Display MVR port debug messages. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug mvrdbg command is the same as the no debug mvrdbg command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
show mvr |
Displays the current MVR configuration. |
debug nvram
Use the debug nvram privileged EXEC command to enable debugging of NVRAM activity. Use the no form of this command to disable debugging.
debug nvram
no debug nvram
Syntax Description
This command has no arguments or keywords.
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug nvram command is the same as the no debug nvram command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
debug pagp
Use the debug pagp privileged EXEC command to enable debugging of Port Aggregation Protocol (PAgP) activity. Use the no form of this command to disable debugging.
debug pagp [all | dual-active | event | fsm | misc | packet]
no debug pagp [all | dual-active | event | fsm | misc | packet]
Syntax Description
all |
(Optional) Display all PAgP debug messages. |
dual-active |
(Optional) Dispaly dual-active detection messages. |
event |
(Optional) Display PAgP event debug messages. |
fsm |
(Optional) Display PAgP finite state-machine debug messages. |
misc |
(Optional) Display miscellaneous PAgP debug messages. |
packet |
(Optional) Display PAgP packet debug messages. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug pagp command is the same as the no debug pagp command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
show pagp |
Displays PAgP channel-group information. |
debug platform acl
Use the debug platform acl privileged EXEC command to enable debugging of the access control list (ACL) manager. Use the no form of this command to disable debugging.
debug platform acl {all | exit | label | main | warn}
no debug platform acl {all | exit | label | main | warn}
Syntax Description
all |
Display all ACL manager debug messages. |
exit |
Display ACL exit-related debug messages. |
label |
Display ACL label-related debug messages. |
main |
Display the main or important ACL debug messages. |
warn |
Display ACL warning-related debug messages. |
Note
Though visible in the command-line help strings, the racl, stack, vacl, and vlmap keywords are not supported.
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug platform acl command is the same as the no debug platform acl command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
debug platform backup interface
Use the debug platform backup interface privileged EXEC command to enable debugging of the Flex Links platform backup interface. Use the no form of this command to disable debugging.
debug platform backup interface
no debug platform backup interface
Syntax Description
This command has no arguments or keywords.
Defaults
Platform backup interface debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug platform backup interface command is the same as the no platform debug backup interface command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
debug platform cpu-queues
Use the debug platform cpu-queues privileged EXEC command to enable debugging of platform central processing unit (CPU) receive queues. Use the no form of this command to disable debugging.
debug platform cpu-queues {broadcast-q | cbt-to-spt-q | cpuhub-q | host-q | icmp-q | igmp-snooping-q | layer2-protocol-q | logging-q | remote-console-q | software-fwd-q | stp-q}
no debug platform cpu-queues {broadcast-q | cbt-to-spt-q | cpuhub-q | host-q | icmp-q | igmp-snooping-q | layer2-protocol-q | logging-q | remote-console-q | software-fwd-q | stp-q}
Syntax Description
broadcast-q |
Display debug messages about packets received by the broadcast queue. |
cbt-to-spt-q |
Display debug messages about packets received by the core-based tree to shortest-path tree (cbt-to-spt) queue. |
cpuhub-q |
Display debug messages about packets received by the CPU heartbeat queue. |
host-q |
Display debug messages about packets received by the host queue. |
icmp-q |
Display debug messages about packets received by the Internet Control Message Protocol (ICMP) queue. |
igmp-snooping-q |
Display debug messages about packets received by the Internet Group Management Protocol (IGMP)-snooping queue. |
layer2-protocol-q |
Display debug messages about packets received by the Layer 2 protocol queue. |
logging-q |
Display debug messages about packets received by the logging queue. |
remote-console-q |
Display debug messages about packets received by the remote console queue. |
software-fwd-q |
Debug packets received by the software forwarding queue. |
stp-q |
Debug packets received by the Spanning Tree Protocol (STP) queue. |
Note
Though visible in the command-line help strings, the routing-protocol-Q and rpffail-q keywords are not supported.
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug platform cpu-queues command is the same as the no debug platform cpu-queues command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
debug platform dot1x
Use the debug platform dot1x privileged EXEC command to enable debugging of IEEE 802.1x events. Use the no form of this command to disable debugging.
debug platform dot1x {initialization | interface-configuration | rpc}
no debug platform dot1x {initialization | interface-configuration | rpc}
Syntax Description
initialization |
Display IEEE 802.1x-authentication initialization sequence debug messages. |
interface-configuration |
Display IEEE 802.1x interface configuration-related debug messages. |
rpc |
Display IEEE 802.1x remote procedure call (RPC) request debug messages. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug platform dot1x command is the same as the no debug platform dot1x command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
debug platform etherchannel
Use the debug platform etherchannel privileged EXEC command to enable debugging of platform-dependent EtherChannel events. Use the no form of this command to disable debugging.
debug platform etherchannel {init | link-up | rpc | warnings}
no debug platform etherchannel {init | link-up | rpc | warnings}
Syntax Description
init |
Display EtherChannel module initialization debug messages. |
link-up |
Display EtherChannel link-up and link-down related debug messages. |
rpc |
Display EtherChannel remote procedure call (RPC) debug messages. |
warnings |
Display EtherChannel warning debug messages. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug platform etherchannel command is the same as the no debug platform etherchannel command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
debug platform forw-tcam
Use the debug platform forw-tcam privileged EXEC command to enable debugging of the forwarding ternary content addressable memory (TCAM) manager. Use the no form of this command to disable debugging.
debug platform forw-tcam [adjustment | allocate | audit | error | move | read | write]
no debug platform forw-tcam [adjustment | allocate | audit | error | move | read | write]
Syntax Description
adjustment |
(Optional) Display TCAM manager adjustment debug messages. |
allocate |
(Optional) Display TCAM manager allocation debug messages. |
audit |
(Optional) Display TCAM manager audit messages. |
error |
(Optional) Display TCAM manager error messages. |
move |
(Optional) Display TCAM manager move messages. |
read |
(Optional) Display TCAM manager read messages. |
write |
(Optional) Display TCAM manager write messages. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
If you do not specify a keyword, all forwarding TCAM manager debug messages appear.
The undebug platform forw-tcam command is the same as the no debug platform forw-tcam command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
debug platform ip dhcp
Use the debug platform ip dhcp privileged EXEC command to debug DHCP events. Use the no form of this command to disable debugging.
debug platform ip dhcp [all | error | event | packet | rpc]
no debug platform ip dhcp [all | error | event | packet | rpc]
Syntax Description
all |
(Optional) Display all DHCP debug messages. |
error |
(Optional) Display DHCP error debug messages. |
event |
(Optional) Display DHCP event debug messages. |
packet |
(Optional) Display DHCP packet-related debug messages. |
rpc |
(Optional) Display DHCP remote procedure call (RPC) request debug messages. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug platform ip dhcp command is the same as the no debug platform ip dhcp command.
Related Commands
debug platform ip igmp snooping
Use the debug platform ip igmp snooping privileged EXEC command to enable debugging of platform-dependent Internet Group Management Protocol (IGMP) snooping. Use the no form of this command to disable debugging.
debug platform ip igmp snooping {all | di | error | event | group | mgmt | pak | retry | rpc | warn}
debug platform ip igmp snooping pak {ip-address | error | ipopt | leave| query | report | rx | svi | tx}
debug platform ip igmp snooping rpc [cfg | misc | vlan]
no debug platform ip igmp snooping {all | di | error | event | group | mgmt | pak | retry | rpc | warn}
Syntax Description
all |
Display all IGMP snooping debug messages. |
di |
Display IGMP snooping destination index (di) coordination remote procedure call (RPC) debug messages. |
error |
Display IGMP snooping error messages. |
event |
Display IGMP snooping event debug messages. |
group |
Display IGMP snooping group debug messages. |
mgmt |
Display IGMP snooping management debug messages. |
pak {ip-address | error | ipopt | leave | query | report | rx | svi | tx} |
Display IGMP snooping packet event debug messages. The keywords have these meanings: • ip-address—IP address of the IGMP group. • error—Display IGMP snooping packet error debug messages. • ipopt—Display IGMP snooping IP bridging options debug messages. • leave—Display IGMP snooping leave debug messages. • query—Display IGMP snooping query debug messages. • report—Display IGMP snooping report debug messages. • rx—Display IGMP snooping received packet debug messages. • svi—Display IGMP snooping switched virtual interface (SVI) packet debug messages. • tx—Display IGMP snooping sent packet debug messages. |
retry |
Display IGMP snooping retry debug messages. |
rpc [cfg | misc | vlan] |
Display IGMP snooping remote procedure call (RPC) event debug messages. The keywords have these meanings: • cfg—(Optional) Display IGMP snooping RPC debug messages. • misc—(Optional) IGMP snooping miscellaneous RPC debug messages. • vlan—(Optional) IGMP snooping VLAN assert RPC debug messages. |
warn |
Display IGMP snooping warning messages. |
Note
Though visible in the command-line help strings, the rpc l3mm keyword is not supported.
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug platform ip igmp snooping command is the same as the no debug platform ip igmp snooping command.
Related Commands
|
|
debug ip igmp snooping |
Displays information about platform-independent IGMP snooping activity. |
show debugging |
Displays information about the types of debugging that are enabled. |
debug platform led
Use the debug platform led privileged EXEC command to enable debugging of light-emitting diode (LED) actions. Use the no form of this command to disable debugging.
debug platform led {generic | signal}
no debug platform led {generic | signal}
Syntax Description
generic |
Display LED generic action debug messages. |
signal |
Display LED signal bit map debug messages. |
Note
Though visible in the command-line help strings, the stack keyword is not supported.
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug platform led command is the same as the no debug platform led command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
debug platform matm
Use the debug platform matm privileged EXEC command to enable debugging of platform-dependent MAC address management. Use the no form of this command to disable debugging.
debug platform matm {aging | all | ec-aging | errors | learning | rpc | secure-address | warnings}
no debug platform matm {aging | all | ec-aging | errors | learning | rpc | secure-address | warnings}
Syntax Description
aging |
Display MAC address aging debug messages. |
all |
Display all platform MAC address management event debug messages. |
ec-aging |
Display EtherChannel address aging-related debug messages. |
errors |
Display MAC address management error messages. |
learning |
Display MAC address management address-learning debug messages. |
rpc |
Display MAC address management remote procedure call (RPC) related debug messages. |
secure-address |
Display MAC address management secure address learning debug messages. |
warning |
Display MAC address management warning messages. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug platform matm command is the same as the no debug platform matm command.
Related Commands
|
|
debug matm |
Displays information about platform-independent MAC address management. |
show debugging |
Displays information about the types of debugging that are enabled. |
debug platform messaging application
Use the debug platform messaging application privileged EXEC command to enable debugging of application messaging activity. Use the no form of this command to disable debugging.
debug platform messaging application {all | badpak | cleanup | events | memerr | messages | usererr}
no debug platform messaging application {all | badpak | cleanup | events | memerr | messages | usererr}
Syntax Description
all |
Display all application-messaging debug messages. |
badpak |
Display bad-packet debug messages. |
cleanup |
Display clean-up debug messages. |
events |
Display event debug messages. |
memerr |
Display memory-error debug messages. |
messages |
Display application-messaging debug messages. |
usererr |
Display user-error debug messages. |
Note
Though visible in the command-line help strings, the stackchg keyword is not supported.
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug platform messaging application command is the same as the no debug platform messaging application command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
debug platform phy
Use the debug platform phy privileged EXEC command to enable debugging of PHY driver information. Use the no form of this command to disable debugging.
debug platform phy {automdix | cablediag | dual-purpose | flcd {configure | ipc | iter | trace} | flowcontrol | forced | init-seq | link-status | read | sfp | show-controller | speed | write | xenpak}
no debug platform phy {automdix | cablediag | dual-purpose | flcd {configure | ipc | iter | trace} | flowcontrol | forced | init-seq | link-status | read | sfp | show-controller | speed | write | xenpak}
Syntax Description
automdix |
Display PHY automatic medium-dependent interface crossover (auto-MDIX) debug messages. |
cablediag |
Display PHY cable-diagnostic debug messages. |
dual-purpose |
Display PHY dual-purpose event debug messages. |
flcd {configure | ipc | iter | trace} |
Display PHY FLCD debug messages. The keywords have these meanings: • configure—Display PHY configure debug messages. • ipc—Display Interprocess Communication Protocol (IPC) debug messages. • iter—Display iter debug messages. • trace—Display trace debug messages. |
flowcontrol |
Display PHY flowcontrol debug messages. |
forced |
Display PHY forced-mode debug messages. |
init-seq |
Display PHY initialization-sequence debug messages. |
link-status |
Display PHY link-status debug messages. |
read |
Display PHY-read debug messages. |
sfp |
Display PHY small form-factor pluggable (SFP) modules debug messages. |
show-controller |
Display PHY show-controller debug messages. |
speed |
Display PHY speed-change debug messages. |
write |
Display PHY-write debug messages. |
xenpak |
Display PHY XENPAK debug messages |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug platform phy command is the same as the no debug platform phy command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
debug platform pm
Use the debug platform pm privileged EXEC command to enable debugging of the platform-dependent port manager software module. Use the no form of this command to disable debugging.
debug platform pm {all | counters | errdisable | etherchnl | exceptions | hpm-events | idb-events | if-numbers | ios-events | link-status | platform | pm-events | pm-span | pm-vectors [detail] | rpc [general | oper-info | state | vectors | vp-events] | soutput-vectors | sync | vlans}
no debug platform pm {all | counters | errdisable | etherchnl | exceptions | hpm-events | idb-events | if-numbers | ios-events | link-status | platform | pm-events | pm-span | pm-vectors [detail] | rpc [general | oper-info | state | vectors | vp-events] | soutput-vectors | sync | vlans}
Syntax Description
all |
Display all port-manager debug messages. |
counters |
Display counters for remote procedure call (RPC) debug messages. |
errdisable |
Display error-disabled related-events debug messages. |
etherchnl |
Display EtherChannel related-events debug messages. |
exceptions |
Display system exception debug messages. |
hpm-events |
Display platform port-manager event debug messages. |
idb-events |
Display interface descriptor block (IDB) related-events debug messages. |
if-numbers |
Display interface-number translation-event debug messages. |
ios-events |
Display Cisco IOS event debug messages. |
link-status |
Display interface link-detection event debug messages. |
platform |
Display port-manager function-event debug messages. |
pm-events |
Display port manager event debug messages. |
pm-span |
Display port manager Switched Port Analyzer (SPAN) event debug messages. |
pm-vectors [detail] |
Display port-manager vector-related-event debug messages. The keyword has this meaning: • detail—Display vector-function details. |
rpc [general | oper-info | state | vectors | vp-events] |
Display RPC related-event debug messages. The keywords have these meanings: • general—(Optional) Display RPC general events. • oper-info—(Optional) Display operational- and informational-related RPC messages. • state—(Optional) Display administrative- and operational-related RPC messages. • vectors—(Optional) Display vector-related RPC messages. • vp-events—(Optional) Display virtual ports related-events RP messages. |
soutput-vectors |
Display IDB output vector event debug messages. |
sync |
Display operational synchronization and VLAN line-state event debug messages. |
vlans |
Display VLAN creation and deletion event debug messages. |
Note
Though visible in the command-line help strings, the stack-manager keyword is not supported.
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug platform pm command is the same as the no debug platform pm command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
debug platform port-asic
Use the debug platform port-asic privileged EXEC command to enable debugging of the port application-specific integrated circuit (ASIC) driver. Use the no form of this command to disable debugging.
debug platform port-asic {interrupt | periodic | read | write}
no debug platform port-asic {interrupt | periodic | read | write}
Syntax Description
interrupt |
Display port-ASIC interrupt-related function debug messages. |
periodic |
Display port-ASIC periodic-function-call debug messages. |
read |
Display port-ASIC read debug messages. |
write |
Display port-ASIC write debug messages. |
Note
Though visible in the command-line help strings, the stack keyword is not supported.
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug platform port-asic command is the same as the no debug platform port-asic command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
debug platform port-security
Use the debug platform port-security privileged EXEC command to enable debugging of platform-dependent port-security information. Use the no form of this command to disable debugging.
debug platform port-security {add | aging | all | delete | errors | rpc | warnings}
no debug platform port-security {add | aging | all | delete | errors | rpc | warnings}
Syntax Description
add |
Display secure address addition debug messages. |
aging |
Display secure address aging debug messages. |
all |
Display all port-security debug messages. |
delete |
Display secure address deletion debug messages. |
errors |
Display port-security error debug messages. |
rpc |
Display remote procedure call (RPC) debug messages. |
warnings |
Display warning debug messages. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug platform port-security command is the same as the no debug platform port-security command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
debug platform qos-acl-tcam
Use the debug platform qos-acl-tcam privileged EXEC command to enable debugging of the quality of service (QoS) and access control list (ACL) ternary content addressable memory (TCAM) manager software. Use the no form of this command to disable debugging.
debug platform qos-acl-tcam {all | ctcam | errors | labels | mask | rpc | tcam}
no debug platform qos-acl-tcam {all | ctcam | errors | labels | mask | rpc | tcam}
Syntax Description
all |
Display all QoS and ACL TCAM (QATM) manager debug messages. |
ctcam |
Display Cisco TCAM (CTCAM) related-events debug messages. |
errors |
Display QATM error-related-events debug messages. |
labels |
Display QATM label-related-events debug messages. |
mask |
Display QATM mask-related-events debug messages. |
rpc |
Display QATM remote procedure call (RPC) related-events debug messages. |
tcam |
Display QATM TCAM-related events debug messages. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug platform qos-acl-tcam command is the same as the no debug platform qos-acl-tcam command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
debug platform resource-manager
Use the debug platform resource-manager privileged EXEC command to enable debugging of the resource manager software. Use the no form of this command to disable debugging.
debug platform resource-manager {all | dm | erd | errors | madmed | sd | stats | vld}
no debug platform resource-manager {all | dm | erd | errors | madmed | sd | stats | vld}
Syntax Description
all |
Display all resource manager debug messages. |
dm |
Display destination-map debug messages. |
erd |
Display equal-cost-route descriptor-table debug messages. |
errors |
Display error debug messages. |
madmed |
Display the MAC address descriptor table and multi-expansion descriptor table debug messages. |
sd |
Display the station descriptor table debug messages. |
stats |
Display statistics debug messages. |
vld |
Display the VLAN-list descriptor debug messages. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug platform resource-manager command is the same as the no debug platform resource-manager command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
debug platform snmp
Use the debug platform snmp privileged EXEC command to enable debugging of the platform-dependent Simple Network Management Protocol (SNMP) software. Use the no form of this command to disable debugging.
debug platform snmp
no debug platform snmp
Syntax Description
This command has no arguments or keywords.
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug platform snmp command is the same as the no debug platform snmp command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
debug platform span
Use the debug platform span privileged EXEC command to enable debugging of the platform-dependent Switched Port Analyzer (SPAN) software. Use the no form of this command to disable debugging.
debug platform span
no debug platform span
Syntax Description
This command has no arguments or keywords.
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug platform span command is the same as the no debug platform span command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
debug platform supervisor-asic
Use the debug platform supervisor-asic privileged EXEC command to enable debugging of the supervisor application-specific integrated circuit (ASIC). Use the no form of this command to disable debugging.
debug platform supervisor-asic {all | errors | receive | send}
no debug platform supervisor-asic {all | errors | receive | send}
Syntax Description
all |
Display all supervisor-ASIC event debug messages. |
errors |
Display the supervisor-ASIC error debug messages. |
receive |
Display the supervisor-ASIC receive debug messages. |
send |
Display the supervisor-ASIC send debug messages. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug platform supervisor-asic command is the same as the no debug platform supervisor-asic command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
debug platform sw-bridge
Use the debug platform sw-bridge privileged EXEC command to enable debugging of the software bridging function. Use the no form of this command to disable debugging.
debug platform sw-bridge {broadcast | control | multicast | packet | unicast}
no debug platform sw-bridge {broadcast | control | multicast | packet | unicast}
Syntax Description
broadcast |
Display broadcast-data debug messages. |
control |
Display protocol-packet debug messages. |
multicast |
Display multicast-data debug messages. |
packet |
Display sent and received data debug messages. |
unicast |
Display unicast-data debug messages. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug platform sw-bridge command is the same as the no debug platform sw-bridge command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
debug platform tcam
Use the debug platform tcam privileged EXEC command to enable debugging of ternary content addressable memory (TCAM) access and lookups. Use the no form of this command to disable debugging.
debug platform tcam {log | read | search | write}
debug platform tcam log l2 {acl {input | output} | local | qos}
debug platform tcam log l3 {acl {input | output} | qos}
debug platform tcam read {reg | ssram | tcam}
debug platform tcam search
debug platform tcam write {forw-ram | reg | tcam}
no debug platform tcam {log | read | search | write}
no debug platform tcam log l2 {acl {input | output} | local | qos}
no debug platform tcam log l3 {acl {input | output} | qos}
no debug platform tcam read {reg | ssram | tcam}
no debug platform tcam search
no debug platform tcam write {forw-ram | reg | tcam}
Syntax Description
log l2 {acl {input | output} | local | qos} |
Display Layer 2 field-based CAM look-up type debug messages. The keywords have these meanings: • acl {input | output}—Display input or output ACL look-up debug messages. • local—Display local forwarding look-up debug messages. • qos—Display classification and quality of service (QoS) look-up debug messages. |
l3 {acl {input | output} | qos} |
Display Layer 3 field-based CAM look-up type debug messages. The keywords have these meanings: • acl {input | output}—Display input or output ACL look-up debug messages. • qos—Display classification and quality of service (QoS) look-up debug messages. |
read {reg | ssram | tcam} |
Display TCAM-read debug messages. The keywords have these meanings: • reg—Display TCAM-register read debug messages. • ssram—Display synchronous static RAM (SSRAM)-read debug messages. • tcam—Display TCAM-read debug messages. |
search |
Display supervisor-initiated TCAM-search results debug messages. |
write {forw-ram | reg | tcam} |
Display TCAM-write debug messages. The keywords have these meanings: forw-ram—Display forwarding-RAM write debug messages. reg—Display TCAM-register write debug messages. tcam—Display TCAM-write debug messages. |
Note
Though visible in the command-line help strings, the l3 ipv6 {acl {input | output} | local | qos | secondary}, the l3 local, and the l3 secondary keywords are not supported.
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug platform tcam command is the same as the no debug platform tcam command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
debug platform udld
Use the debug platform udld privileged EXEC command to enable debugging of the platform-dependent UniDirectional Link Detection (UDLD) software. Use the no form of this command to disable debugging.
debug platform udld [all | error | rpc {events | messages}]
no debug platform udld [all | error | rpc {events | messages}]
Syntax Description
all |
(Optional) Display all UDLD debug messages. |
error |
(Optional) Display error condition debug messages. |
rpc {events | messages} |
(Optional) Display UDLD remote procedure call (RPC) debug messages. The keywords have these meanings: • events—Display UDLD RPC events. • messages—Display UDLD RPC messages. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug platform udld command is the same as the no debug platform udld command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
debug platform vlan
Use the debug platform vlan privileged EXEC command to enable debugging of the VLAN manager software. Use the no form of this command to disable debugging.
debug platform vlan {errors | mvid | rpc}
no debug platform vlan {errors | mvid | rpc}
Syntax Description
errors |
Display VLAN error debug messages. |
mvid |
Display mapped VLAN ID allocations and free debug messages. |
rpc |
Display remote procedure call (RPC) debug messages. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug platform vlan command is the same as the no debug platform vlan command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
debug pm
Use the debug pm privileged EXEC command to enable debugging of port manager (PM) activity. The port manager is a state machine that controls all the logical and physical interfaces. All features, such as VLANs, UniDirectional Link Detection (UDLD), and so forth, work with the port manager to provide switch functions. Use the no form of this command to disable debugging.
debug pm {all | assert | card | etherchnl | hatable | messages | port | redundancy | registry | sm | span | split | vlan | vp}
no debug pm {all | assert | card | etherchnl | hatable | messages | port | redundancy | registry | sm | span | split | vlan | vp}
Syntax Description
all |
Display all PM debug messages. |
assert |
Display assert debug messages. |
card |
Display line-card related-events debug messages. |
etherchnl |
Display EtherChannel related-events debug messages. |
hatable |
Display Host Access Table events debug messages. |
messages |
Display PM debug messages. |
port |
Display port related-events debug messages. |
redundancy |
Display redundancy debug messages. |
registry |
Display PM registry invocation debug messages. |
sm |
Display state-machine related-events debug messages. |
span |
Display spanning-tree related-events debug messages. |
split |
Display split-processor debug messages. |
vlan |
Display VLAN related-events debug messages. |
vp |
Display virtual port related-events debug messages. |
Note
Though visible in the command-line help strings, the scp and pvlan keywords are not supported.
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug pm command is the same as the no debug pm command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
debug port-security
Use the debug port-security privileged EXEC command to enable debugging of the allocation and states of the port security subsystem. Use the no form of this command to disable debugging.
debug port-security
no debug port-security
Syntax Description
This command has no arguments or keywords.
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug port-security command is the same as the no debug port-security command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
show port-security |
Displays port-security settings for an interface or for the switch. |
debug ptp
Use the debug ptp privileged EXEC command to enable debugging of the Precision Time Protocol (PTP) activity. Use the no form of this command to disable debugging.
debug ptp {bmc | clock-correction | errors | event | messages | error | transparent-clock}
no debug ptp {bmc | clock-correction | errors | event | messages | error | transparent-clock}
Syntax Description
bmc |
Display the PTP best master clock algorithm debug messages. |
clock-correction |
Display the PTP clock correction debug messages. |
error |
Display the PTP error debug messages. |
event |
Display the PTP state event debug messages. |
messages |
Display the PTP debug messages. |
transparent-clock |
Display the PTP transparent-clock debug messages. |
Command Default
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(46)SE1 |
This command was introduced. |
Usage Guidelines
The undebug ptp command is the same as the no debug ptp command.
Related Commands
h
debug qos-manager
Use the debug qos-manager privileged EXEC command to enable debugging of the quality of service (QoS) manager software. Use the no form of this command to disable debugging.
debug qos-manager {all | event | verbose}
no debug qos-manager {all | event | verbose}
Syntax Description
all |
Display all QoS-manager debug messages. |
event |
Display QoS-manager related-event debug messages. |
verbose |
Display QoS-manager detailed debug messages. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug qos-manager command is the same as the no debug qos-manager command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
debug spanning-tree
Use the debug spanning-tree privileged EXEC command to enable debugging of spanning-tree activities. Use the no form of this command to disable debugging.
debug spanning-tree {all | backbonefast | bpdu | bpdu-opt | config | etherchannel | events | exceptions | general | mstp | pvst+ | root | snmp | switch | synchronization | uplinkfast}
no debug spanning-tree {all | backbonefast | bpdu | bpdu-opt | config | etherchannel | events | exceptions | general | mstp | pvst+ | root | snmp | switch | synchronization | uplinkfast}
Syntax Description
all |
Display all spanning-tree debug messages. |
backbonefast |
Display BackboneFast-event debug messages. |
bpdu |
Display spanning-tree bridge protocol data unit (BPDU) debug messages. |
bpdu-opt |
Display optimized BPDU handling debug messages. |
config |
Display spanning-tree configuration change debug messages. |
etherchannel |
Display EtherChannel-support debug messages. |
events |
Display spanning-tree topology event debug messages. |
exceptions |
Display spanning-tree exception debug messages. |
general |
Display general spanning-tree activity debug messages. |
mstp |
Debug Multiple Spanning Tree Protocol events. |
pvst+ |
Display per-VLAN spanning-tree plus (PVST+) event debug messages. |
root |
Display spanning-tree root-event debug messages. |
snmp |
Display spanning-tree Simple Network Management Protocol (SNMP) handling debug messages. |
synchronization |
Display the spanning-tree synchronization event debug messages. |
switch |
Display switch shim command debug messages. This shim is the software module that is the interface between the generic Spanning Tree Protocol (STP) code and the platform-specific code of various switch platforms. |
uplinkfast |
Display UplinkFast-event debug messages. |
Note
Though visible in the command-line help strings, the csuf/csrt keyword is not supported.
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug spanning-tree command is the same as the no debug spanning-tree command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
show spanning-tree |
Displays spanning-tree state information. |
debug spanning-tree backbonefast
Use the debug spanning-tree backbonefast privileged EXEC command to enable debugging of spanning-tree BackboneFast events. Use the no form of this command to disable debugging.
debug spanning-tree backbonefast [detail | exceptions]
no debug spanning-tree backbonefast [detail | exceptions]
Syntax Description
detail |
(Optional) Display detailed BackboneFast debug messages. |
exceptions |
(Optional) Display spanning-tree BackboneFast-exception debug messages. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug spanning-tree backbonefast command is the same as the no debug spanning-tree backbonefast command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
show spanning-tree |
Displays spanning-tree state information. |
debug spanning-tree bpdu
Use the debug spanning-tree bpdu privileged EXEC command to enable debugging of sent and received spanning-tree bridge protocol data units (BPDUs). Use the no form of this command to disable debugging.
debug spanning-tree bpdu [receive | transmit]
no debug spanning-tree bpdu [receive | transmit]
Syntax Description
receive |
(Optional) Display the nonoptimized path for received BPDU debug messages. |
transmit |
(Optional) Display the nonoptimized path for sent BPDU debug messages. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug spanning-tree bpdu command is the same as the no debug spanning-tree bpdu command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
show spanning-tree |
Displays spanning-tree state information. |
debug spanning-tree bpdu-opt
Use the debug spanning-tree bpdu-opt privileged EXEC command to enable debugging of optimized spanning-tree bridge protocol data units (BPDUs) handling. Use the no form of this command to disable debugging.
debug spanning-tree bpdu-opt [detail | packet]
no debug spanning-tree bpdu-opt [detail | packet]
Syntax Description
detail |
(Optional) Display detailed optimized BPDU-handling debug messages. |
packet |
(Optional) Display packet-level optimized BPDU-handling debug messages. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug spanning-tree bpdu-opt command is the same as the no debug spanning-tree bpdu-opt command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
show spanning-tree |
Displays spanning-tree state information. |
debug spanning-tree mstp
Use the debug spanning-tree mstp privileged EXEC command to enable debugging of the Multiple Spanning Tree Protocol (MSTP) software. Use the no form of this command to disable debugging.
debug spanning-tree mstp {all | boundary | bpdu-rx | bpdu-tx | errors | flush | init | migration | pm | proposals | region | roles | sanity_check | sync | tc | timers}
no debug spanning-tree mstp {all | boundary | bpdu-rx | bpdu-tx | errors | flush | init | migration | pm | proposals | region | roles | sanity_check | sync | tc | timers}
Syntax Description
all |
Enable all the debugging messages. |
boundary |
Debug flag changes at these boundaries: • An multiple spanning-tree (MST) region and a single spanning-tree region running Rapid Spanning Tree Protocol (RSTP) • An MST region and a single spanning-tree region running 802.1D • An MST region and another MST region with a different configuration |
bpdu-rx |
Debug the received MST bridge protocol data units (BPDUs). |
bpdu-tx |
Debug the sent MST BPDUs. |
errors |
Debug MSTP errors. |
flush |
Debug the port flushing mechanism. |
init |
Debug the initialization of the MSTP data structures. |
migration |
Debug the protocol migration state machine. |
pm |
Debug MSTP port manager events. |
proposals |
Debug handshake messages between the designated switch and the root switch. |
region |
Debug the region synchronization between the switch processor (SP) and the route processor (RP). |
roles |
Debug MSTP roles. |
sanity_check |
Debug the received BPDU sanity check messages. |
sync |
Debug the port synchronization events. |
tc |
Debug topology change notification events. |
timers |
Debug the MSTP timers for start, stop, and expire events. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug spanning-tree mstp command is the same as the no debug spanning-tree mstp command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
show spanning-tree |
Displays spanning-tree state information. |
debug spanning-tree switch
Use the debug spanning-tree switch privileged EXEC command to enable debugging of the software interface between the Spanning Tree Protocol (STP) software module and the port manager software module. Use the no form of this command to disable debugging.
debug spanning-tree switch {all | errors | flush | general | helper | pm | rx {decode | errors | interrupt | process} | state | tx [decode] | uplinkfast}
no debug spanning-tree switch {all | errors | flush | general | helper | pm | rx {decode | errors | interrupt | process} | state | tx [decode] | uplinkfast}
Syntax Description
all |
Display all spanning-tree switch debug messages. |
errors |
Display debug messages for the interface between the spanning-tree software module and the port manager software module. |
flush |
Display debug messages for the shim flush operation. |
general |
Display general event debug messages. |
helper |
Display spanning-tree helper-task debug messages. Helper tasks handle bulk spanning-tree updates. |
pm |
Display port-manager event debug messages. |
rx |
Display received bridge protocol data unit (BPDU) handling debug messages. The keywords have these meanings: • decode—Display decoded received packets. • errors—Display receive error debug messages. • interrupt—Display interrupt service request (ISR) debug messages. • process—Display process receive BPDU debug messages. |
state |
Display spanning-tree port state change debug messages; |
tx [decode] |
Display sent BPDU handling debug messages. The keyword has this meaning: • decode—(Optional) Display decoded sent packets. |
uplinkfast |
Display uplinkfast packet transmission debug messages. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug spanning-tree switch command is the same as the no debug spanning-tree switch command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
show spanning-tree |
Displays spanning-tree state information. |
debug spanning-tree uplinkfast
Use the debug spanning-tree uplinkfast privileged EXEC command to enable debugging of spanning-tree UplinkFast events. Use the no form of this command to disable debugging.
debug spanning-tree uplinkfast [exceptions]
no debug spanning-tree uplinkfast [exceptions]
Syntax Description
exceptions |
(Optional) Display spanning-tree UplinkFast-exception debug messages. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug spanning-tree uplinkfast command is the same as the no debug spanning-tree uplinkfast command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
show spanning-tree |
Displays spanning-tree state information. |
debug sw-vlan
Use the debug sw-vlan privileged EXEC command to enable debugging of VLAN manager activities. Use the no form of this command to disable debugging.
debug sw-vlan {badpmcookies | cfg-vlan {bootup | cli} | events | ifs | management | mapping | notification | packets | redundancy | registries | vtp}
no debug sw-vlan {badpmcookies | cfg-vlan {bootup | cli} | events | ifs | management | mapping | notification | packets | redundancy | registries | vtp}
Syntax Description
badpmcookies |
Display debug messages for VLAN manager incidents of bad port manager cookies. |
cfg-vlan {bootup | cli} |
Display config-vlan debug messages. The keywords have these meanings: • bootup—Display messages when the switch is booting up. • cli—Display messages when the command-line interface (CLI) is in config-vlan mode. |
events |
Display debug messages for VLAN manager events. |
ifs |
See the debug sw-vlan ifs command. |
management |
Display debug messages for VLAN manager management of internal VLANs. |
mapping |
Display debug messages for VLAN mapping. |
notification |
See the debug sw-vlan notification command. |
packets |
Display debug messages for packet handling and encapsulation processes. |
redundancy |
Display debug messages for VTP VLAN redundancy. |
registries |
Display debug messages for VLAN manager registries. |
vtp |
See the debug sw-vlan vtp command. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug sw-vlan command is the same as the no debug sw-vlan command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
show vlan |
Displays the parameters for all configured VLANs or one VLAN (if the VLAN name or ID is specified) in the administrative domain. |
show vtp |
Displays general information about VTP management domain, status, and counters. |
debug sw-vlan ifs
Use the debug sw-vlan ifs privileged EXEC command to enable debugging of the VLAN manager IOS file system (IFS) error tests. Use the no form of this command to disable debugging.
debug sw-vlan ifs {open {read | write} | read {1 | 2 | 3 | 4} | write}
no debug sw-vlan ifs {open {read | write} | read {1 | 2 | 3 | 4} | write}
Syntax Description
open {read | write} |
Display VLAN manager IFS file-open operation debug messages. The keywords have these meanings: • read—Display VLAN manager IFS file-read operation debug messages. • write—Display VLAN manager IFS file-write operation debug messages. |
read {1 | 2 | 3 | 4} |
Display file-read operation debug messages for the specified error test (1, 2, 3, or 4). |
write |
Display file-write operation debug messages. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug sw-vlan ifs command is the same as the no debug sw-vlan ifs command.
When selecting the file read operation, Operation 1 reads the file header, which contains the header verification word and the file version number. Operation 2 reads the main body of the file, which contains most of the domain and VLAN information. Operation 3 reads type length version (TLV) descriptor structures. Operation 4 reads TLV data.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
show vlan |
Displays the parameters for all configured VLANs or one VLAN (if the VLAN name or ID is specified) in the administrative domain. |
debug sw-vlan notification
Use the debug sw-vlan notification privileged EXEC command to enable debugging of the activation and deactivation of Inter-Link Switch (ISL) VLAN IDs. Use the no form of this command to disable debugging.
debug sw-vlan notification {accfwdchange | allowedvlancfgchange | fwdchange | linkchange | modechange | pruningcfgchange | statechange}
no debug sw-vlan notification {accfwdchange | allowedvlancfgchange | fwdchange | linkchange | modechange | pruningcfgchange | statechange}
Syntax Description
accfwdchange |
Display debug messages for VLAN manager notification of aggregated access interface spanning-tree forward changes. |
allowedvlancfgchange |
Display debug messages for VLAN manager notification of changes to the allowed VLAN configuration. |
fwdchange |
Display debug messages for VLAN manager notification of spanning-tree forwarding changes. |
linkchange |
Display debug messages for VLAN manager notification of interface link-state changes. |
modechange |
Display debug messages for VLAN manager notification of interface mode changes. |
pruningcfgchange |
Display debug messages for VLAN manager notification of changes to the pruning configuration. |
statechange |
Display debug messages for VLAN manager notification of interface state changes. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug sw-vlan notification command is the same as the no debug sw-vlan notification command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
show vlan |
Displays the parameters for all configured VLANs or one VLAN (if the VLAN name or ID is specified) in the administrative domain. |
debug sw-vlan vtp
Use the debug sw-vlan vtp privileged EXEC command to enable debugging of the VLAN Trunking Protocol (VTP) code. Use the no form of this command to disable debugging.
debug sw-vlan vtp {events | packets | pruning [packets | xmit] | redundancy | xmit}
no debug sw-vlan vtp {events | packets | pruning | redundancy | xmit}
Syntax Description
events |
Display debug messages for general-purpose logic flow and detailed VTP messages generated by the VTP_LOG_RUNTIME macro in the VTP code. |
packets |
Display debug messages for the contents of all incoming VTP packets that have been passed into the VTP code from the IOS VTP platform-dependent layer, except for pruning packets. |
pruning [packets | xmit] |
Display debug messages generated by the pruning segment of the VTP code. The keywords have these meanings: • packets—(Optional) Display debug messages for the contents of all incoming VTP pruning packets that have been passed into the VTP code from the IOS VTP platform-dependent layer. • xmit—(Optional) Display debug messages for the contents of all outgoing VTP packets that the VTP code requests the IOS VTP platform-dependent layer to send. |
redundancy |
Display debug messages for VTP redundancy. |
xmit |
Display debug messages for the contents of all outgoing VTP packets that the VTP code requests the IOS VTP platform-dependent layer to send, except for pruning packets. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug sw-vlan vtp command is the same as the no debug sw-vlan vtp command.
If no further parameters are entered after the pruning keyword, VTP pruning debugging messages appear. They are generated by the VTP_PRUNING_LOG_NOTICE, VTP_PRUNING_LOG_INFO, VTP_PRUNING_LOG_DEBUG, VTP_PRUNING_LOG_ALERT, and VTP_PRUNING_LOG_WARNING macros in the VTP pruning code.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
show vtp |
Displays general information about VTP management domain, status, and counters. |
debug udld
Use the debug udld privileged EXEC command to enable debugging of the UniDirectional Link Detection (UDLD) feature. Use the no form of this command to disable UDLD debugging.
debug udld {events | packets | registries}
no debug udld {events | packets | registries}
Syntax Description
events |
Display debug messages for UDLD process events as they occur. |
packets |
Display debug messages for the UDLD process as it receives packets from the packet queue and tries to send them at the request of the UDLD protocol code. |
registries |
Display debug messages for the UDLD process as it processes registry calls from the UDLD process-dependent module and other feature modules. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug udld command is the same as the no debug udld command.
For debug udld events, these debugging messages appear:
•
General UDLD program logic flow
•
State machine state changes
•
Program actions for the set and clear ErrDisable state
•
Neighbor cache additions and deletions
•
Processing of configuration commands
•
Processing of link-up and link-down indications
For debug udld packets, these debugging messages appear:
•
General packet processing program flow on receipt of an incoming packet
•
Indications of the contents of the various pieces of packets received (such as type length versions [TLVs]) as they are examined by the packet reception code
•
Packet transmission attempts and the outcome
For debug udld registries, these categories of debugging messages appear:
•
Sub-block creation
•
Fiber-port status changes
•
State change indications from the port manager software
•
MAC address registry calls
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |
show udld |
Displays UDLD administrative and operational status for all ports or the specified port. |
debug vqpc
Use the debug vqpc privileged EXEC command to enable debugging of the VLAN Query Protocol (VQP) client. Use the no form of this command to disable debugging.
debug vqpc [all | cli | events | learn | packet]
no debug vqpc [all | cli | events | learn | packet]
Syntax Description
all |
(Optional) Display all VQP client debug messages. |
cli |
(Optional) Display the VQP client command-line interface (CLI) debug messages. |
events |
(Optional) Display VQP client event debug messages. |
learn |
(Optional) Display VQP client address learning debug messages. |
packet |
(Optional) Display VQP client packet information debug messages. |
Defaults
Debugging is disabled.
Command Modes
Privileged EXEC
Command History
|
|
12.2(44)EX |
This command was introduced. |
Usage Guidelines
The undebug vqpc command is the same as the no debug vqpc command.
Related Commands
|
|
show debugging |
Displays information about the types of debugging that are enabled. |