Server Specifications
This appendix lists the physical, environmental, and power specifications for the server.
Physical Specifications
The following figure shows the height, width, and depth of the chassis as measured to different locations.
The following table lists additional physical specifications for the server versions.
|
Description |
Specification |
|---|---|
|
Server weight |
|
|
Front Clearance |
3 in. (76 mm) |
|
Side Clearance |
1 in. (25 mm) |
|
Rear Clearance |
6 in. (152 mm) |
Environmental Specifications
As a Class A2 product, the server has the following environmental specifications.
|
Description |
Specification |
|
Temperature, Operating |
Dry bulb temperature of 10°C to 35°C (50°F to 95°F) Maximum temperature change of 20°C (36°F) per hour (a temperature change within a specified period of time and not a rate of change) Humidity condition: Uncontrolled, not to exceed 50% RH starting condition Derate the maximum temperature by 1°C (33.8°F) per every 305 meters of altitude above 900m |
| Temperature, Extended Operating |
5°C to 40°C (41°F to 104°F) with no direct sunlight Humidity condition: Uncontrolled, not to exceed 50% RH starting condition Derate the maximum temperature by 1°C (33.8°F) per every 305 meters of altitude above 900m |
|
Temperature, non-operating (when the server is stored or transported) |
Dry bulb temperature of 40 °C to 65 °C (-40°F to 149 °F) |
|
Humidity (RH), operating |
10% to 90% and 28°C (82.4°F) maximum dew-point temperature, non-condensing environment Minimum to be higher (more moisture) of -12 ˚C (10.4 ˚F) dew point or 8% relative humidity Maximum to be 24 ˚C (75.2 ˚F) dew point or 90% relative humidity |
|
Humidity (RH), non-operating (when the server is stored or transported) |
5% to 93% relative humidity, non-condensing, with a maximum wet bulb temperature of 28 °C across the 20 °C to 40 °C dry bulb range. |
|
Altitude, operating |
A maximum elevation of 3050 meters (10,006 feet) |
|
Altitude, non-operating (when the server is stored or transported) |
An elevation of 0 to 12,000 meters (39,370 feet) |
|
Maximum Operating Duration |
Unlimited |
|
Sound power level Measure A-weighted per ISO7779 LwAd (Bels) Operation at 73°F (23°C) |
5.5 |
|
Sound pressure level Measure A-weighted per ISO7779 LpAm (dBA) Operation at 73°F (23°C) |
40 |
Power Specifications
 Note |
Do not mix power supply types or wattages in the server. Both power supplies must be identical. |
You can get more specific power information for your exact server configuration by using the Cisco UCS Power Calculator:
The power specifications for the supported power supply options are listed in the following sections.
1050 W AC Power Supply
This section lists the specifications for each 1050 W AC power supply (Cisco part number UCSC-PSU1-1050W).
|
Description |
Specification |
|
AC Input Voltage |
Nominal range: 100–120 VAC, 200–240 VAC (Range: 90–132 VAC, 180–264 VAC) |
|
AC Input Frequency |
Nominal range: 50 to 60Hz (Range: 47–63 Hz) |
|
Maximum AC Input current |
12.5 A at 100 VAC 6.0 A at 208 VAC |
|
Maximum input volt-amperes |
1250 VA at 100 VAC |
|
Maximum inrush current |
15 A (sub-cycle duration) |
|
Maximum hold-up time |
12 ms at 1050 W |
|
Maximum output power per PSU |
800 W at 100–120 VAC 1050 W at 200–240 VAC |
|
Power supply output voltage |
12 VDC |
|
Power supply standby voltage |
12 VDC |
|
Efficiency rating |
Climate Savers Platinum Efficiency (80Plus Platinum certified) |
|
Form factor |
RSP2 |
|
Input connector |
IEC320 C14 |
1050 W DC Power Supply
This section lists the specifications for each 1050 W DC power supply (Cisco part number UCSC-PSUV2-1050DC).
|
Description |
Specification |
|
DC Input Voltage |
Nominal range: -48 to -60 VDC (Range: -40 to -72 VDC) |
|
Maximum DC input current |
N32 A at -40 VDC |
|
Maximum input wattage |
1234 W |
|
Maximum inrush current |
35 A (sub-cycle duration) |
|
Maximum hold-up time |
5 ms at 100% load (1050 W main and 36 W standby) |
|
Maximum output power per PSU |
1050 W on 12 VDC main power 36 W on 12 VDC standby power |
|
Power supply output voltage |
12 VDC |
|
Power supply standby voltage |
12 VDC |
|
Efficiency rating |
≥ 92% at 50% load |
|
Form factor |
RSP2 |
|
Input connector |
Fixed 3-wire block |
1200 W AC Power Supply
This section lists the specifications for each 1200 W AC power supply (Cisco part number UCSC-PSU1-1200W-D).
|
Description |
Specification |
|
AC input voltage |
Range: 100–230 VAC |
|
AC input frequency |
Range: 50 to 60Hz |
|
Maximum AC input current |
12.97 A at 100 VAC |
|
Maximum input volt-amperes |
1345 VA at 208 VAC |
|
Maximum inrush current |
20 A |
|
Maximum hold-up time |
12 ms at 1200 W |
|
Maximum output power per PSU |
1100 W at 100–120 VAC 1200 W at 208–230 VAC |
|
Power supply output voltage |
12 VDC |
|
Power supply standby voltage |
12 VDC |
|
Efficiency rating |
Climate Savers Platinum Efficiency (80Plus Titanium certified) |
|
Form factor |
RSP2 |
|
Input connector |
IEC320 C14 |
1600 W AC Power Supply
This section lists the specifications for each 1600 W AC power supply (Cisco part number UCSC-PSU1-1600W).
|
Description |
Specification |
|
AC Input Voltage |
Nominal range: 200–240 VAC (Range: 180–264 VAC) |
|
AC Input Frequency |
Nominal range: 50 to 60Hz (Range: 47–63 Hz) |
|
Maximum AC Input current |
9.5 A at 200 VAC |
|
Maximum input volt-amperes |
1250 VA at 200 VAC |
|
Maximum inrush current |
30 A at 35° C |
|
Maximum hold-up time |
80 ms at 1600 W |
|
Maximum output power per PSU |
1600 W at 200–240 VAC |
|
Power supply output voltage |
12 VDC |
|
Power supply standby voltage |
12 VDC |
|
Efficiency rating |
Climate Savers Platinum Efficiency (80Plus Platinum certified) |
|
Form factor |
RSP2 |
|
Input connector |
IEC320 C14 |
2300 W AC Power Supply
Note |
For the 80PLUS platinum certification documented in the following table, you can find test results at https://www.clearesult.com/80plus/. |
This section lists the specifications for each 2300 W AC power supply (Cisco part number UCSC-PSU1-2300).
|
Parameter |
Specification |
|||
|---|---|---|---|---|
|
Input Connector |
IEC320 C20 |
|||
|
Input Voltage Range (V rms) |
100 to 240 |
|||
|
Maximum Allowable Input Voltage Range (V rms) |
90 to 264 |
|||
|
Frequency Range (Hz) |
50 to 60 |
|||
|
Maximum Allowable Frequency Range (Hz) |
47 to 63 |
|||
|
Maximum Rated Output (W) Limited to 800W when operating at low-line input voltage, 100-127 V |
2300 |
|||
|
Maximum Rated Standby Output (W) |
36 |
|||
|
Nominal Input Voltage (V rms) |
100 |
120 |
208 |
230 |
|
Nominal Input Current (A rms) |
13 |
11 |
12 |
10.8 |
|
Maximum Input at Nominal Input Voltage (W) |
1338 |
1330 |
2490 |
2480 |
|
Maximum Input at Nominal Input Voltage (VA) |
1351 |
1343 |
2515 |
2505 |
|
Maximum Rated Efficiency (%) Minimum rating required to achieve 80PLUS platinum certification. |
92 |
92 |
93 |
93 |
|
Maximum Rated Power Factor Minimum rating required to achieve 80PLUS platinum certification. |
0.99 |
0.99 |
0.97 |
0.97 |
|
Maximum Inrush Current (peak A) |
30 |
|||
|
Maximum Inrush Current (ms) |
0.2 |
|||
|
Maximum Ride-Through Time Time output voltage remains within regulation limits at 100% load, during input voltage dropout |
12 |
|||
Power Cord Specifications
Each power supply in the server has a power cord. Standard power cords or jumper power cords are available for connection to the server. The shorter jumper power cords, for use in racks, are available as an optional alternative to the standard power cords.
Note |
Only the approved power cords or jumper power cords listed below are supported. |
|
Description |
Length (Feet) |
Length (Meters) |
|
CAB-48DC-40A-8AWG DC power cord, -48 VDC, 40 A, 8 AWG Three-socket Mini-Fit connector to three-wire |
11.7 |
3.5 |
|
CAB-C13-C14-AC AC power cord, 10 A; C13 to C14, recessed receptacle |
9.8 |
3.0 |
|
CAB-250V-10A-AR AC power cord, 250 V, 10 A Argentina |
8.2 |
2.5 |
|
CAB-C13-C14-2M-JP AC Power Cord, C13 to C14 Japan PSE Mark |
6.6 |
2.0 |
|
CAB-9K10A-EU AC Power Cord, 250 V, 10 A; CEE 7/7 Plug Europe |
8.2 |
2.5 |
|
CAB-250V-10A-IS AC Power Cord, 250 V, 10 A Israel |
8.2 |
2.5 |
|
CAB-250V-10A-CN AC power cord, 250 V, 10 A PR China |
8.2 |
2.5 |
|
CAB-ACTW AC power cord, 250 V, 10 A Taiwan |
7.5 |
2.3 |
|
CAB-C13-CBN AC cabinet jumper power cord, 250, 10 A, C13 to C14 |
2.2 |
0.68 |
|
CAB-C13-C14-2M AC cabinet jumper power cord, 250 V, 10 A, C13 to C14 |
6.6 |
2.0 |
|
CAB-9K10A-AU AC power cord, 250 V, 10 A, 3112 plug, Australia |
8.2 |
2.5 |
|
CAB-N5K6A-NA AC power cord, 200/240 V, 6 A, North America |
8.2 |
2.5 |
|
CAB-250V-10A-ID AC power Cord, 250 V, 10 A, India |
8.2 |
2.5 |
|
CAB-9K10A-SW AC power cord, 250 V, 10 A, MP232 plug Switzerland |
8.2 |
2.5 |
|
CAB-250V-10A-BR AC power Cord, 250 V, 10 A Brazil |
8.2 |
2.5 |
|
CAB-9K10A-UK AC power cord, 250 V, 10 A (13 A fuse), BS1363 plug United Kingdom |
8.2 |
2.5 |
|
CAB-9K12A-NA AC power cord, 125 V, 13 A, NEMA 5-15 plug North America |
8.2 |
2.5 |
|
CAB-AC-L620-C13 AC power cord, NEMA L6-20 to C13 connectors |
6.6 |
2.0 |
|
CAB-9K10A-IT AC power cord, 250 V, 10 A, CEI 23-16/VII plug Italy |
8.2 |
2.5 |
|
R2XX-DMYMPWRCORD No power cord; PID option for ordering server with no power cord |
NA |
NA |
Feedback