Global Service Profiles
Global service profiles centralize the logical configuration deployed across the data center. This centralization enables the maintenance of all service profiles in the Cisco UCS domains, from one central location in Cisco UCS Central. When you use a global service profile, you can do the following across the data center:
-
Pick a compute element for the service profile from any of the Cisco UCS domains.
-
Migrate the service profile from one element to another.
-
Select servers from the available global server pools from any of the Cisco UCS domains.
-
Associate global resources such as ID pools and policies.
-
Reference to any of the global policies in the Cisco UCS domain.
Creating Global Service Profiles
You can create a global service profile from Cisco UCS Central GUI or Cisco UCS Central CLI or as regular service profiles from Cisco UCS Manager and reference the global polices. When you create the global service profile from Cisco UCS Central, you can create ID pools, vNICs and vHBAs in Cisco UCS Central and reference to the ID.
Configuring Management IP Addresses for Global Service Profiles
- Zero or one outband IPv4 address, through which traffic traverses the fabric interconnect through the management port.
- Zero or one inband (IPv4 or IPv6) address, through which traffic traverses the fabric interconnect through the fabric uplink port.
You can configure either a pooled or a static management IP address through the Cisco UCS Central GUI or CLI. However, while creating a global service profile using the global service profile template, you can only configure a pooled management IP address. Static IP address is not supported for this release.
Guidelines and Cautions for Global Service Profile
Make sure to remember the following when you are creating global service profiles:
-
When you create a global service profile in Cisco UCS Central, the system validates the following information:
-
Use od ID along with vNICs, vHBAs, iSCSI vNICs etc
-
vLAN and vSAN assignment
-
Association to the compute element based on the availability index
-
Server qualification criteria
Any incompatibility in these information will be flagged. You can successfully create the global service profile only after resolving these issues.
-
-
After any of the policy reference is resolved in the global service profile, if any of the remote policy is changed, that will result in reconfiguration of the global service profile.
-
The VLANs and VSANs in Cisco UCS Central belong to domain groups. Make sure to create the VLANS or VSANs under a domain group. In case of VLAN also assign them to Orgs before a vNIC or vHBA from the global service profile can access the VLAN or VSAN.
-
You can modify, disassociate or delete any of the global service profile only from Cisco UCS Central.
-
You can rename a global service profile only from Cisco UCS Central. When you rename a service profile, Cisco UCS Central deletes the global service profile with old name and creates a new service profile with the new name in the inventory.
-
If a server that is associated to the global service profile is removed from the Cisco UCS domain, when you re-acknowledge the server, it will be unassociated from the service profile.
-
You cannot define or access domain specific policies, such as multi-cast policy and flow-control policy from Cisco UCS Central. But, you can reference to these policies from Cisco UCS Central by global service profile resources. When you define the global service profile, you can view the available domain specific policies and refer to them in the service profile by name. When the service profile is deployed, the Cisco UCS domain resolves to the policy and includes it in the service profile for that domain.
-
You can localize a global service profile from the deployed Cisco UCS Manager. When you localize, the global service profile is deleted from Cisco UCS Central. But all the global policies still remain global. If you want to localize the global policies, you have to localize each policy separately.
Creating a Global Service Profile
Procedure
Command or Action | Purpose | |||
---|---|---|---|---|
Step 1 |
UCSC# connect resource-mgr |
Enters resource manager mode. |
||
Step 2 |
UCSC(resource-mgr) # scope org |
Enters organization mode for the specified organization. To enter the root organization mode, type / as the org-name . |
||
Step 3 |
UCSC(resource-mgr)# /org # create service-profile profile-name instance |
Creates the specified service profile and enters organization service profile mode. This name can be between 2 and 32 alphanumeric characters. You cannot use spaces or any special characters other than - (hyphen), _ (underscore), : (colon), and . (period), and this name must be unique across all service profiles and service profile templates within the same organization. |
||
Step 4 |
UCSC(resource-mgr) /org/service-profile # set bios-policy policy-name |
Associates the specified BIOS policy with the service profile. |
||
Step 5 |
UCSC(resource-mgr) /org/service-profile # set boot-policy policy-name |
Associates the specified boot policy with the service profile. |
||
Step 6 |
(Optional) UCSC(resource-mgr) /org/service-profile # set descr description |
(Optional)
Provides a description for the service profile.
|
||
Step 7 |
UCSC(resource-mgr) /org/service-profile # set dynamic-vnic-conn-policy policy-name |
Associates the specified dynamic vNIC connection policy with the service profile. |
||
Step 8 |
UCSC(resource-mgr) /org/service-profile # set extippoolname pool-name |
Associates the specified external IP pool with the service profile. |
||
Step 9 |
UCSC(resource-mgr) /org/service-profile # set extipstate pool-name |
Specifies how the external IP address will be assigned to the service profile.
|
||
Step 10 |
UCSC(resource-mgr) /org/service-profile # set host-fw-policy policy-name |
Associates the specified host firmware policy with the service profile. |
||
Step 11 |
UCSC(resource-mgr) /org/service-profile # set identity {dynamic-uuid {uuid | derived} | dynamic-wwnn {wwnn | derived} | uuid-pool pool-name | wwnn-pool pool-name} |
Specifies how the server acquires a UUID or WWNN. You can do one of the following:
|
||
Step 12 |
UCSC(resource-mgr) /org/service-profile # set ipmi-access-profile profile-name |
Associates the specified IPMI access profile with the service profile. |
||
Step 13 |
UCSC(resource-mgr) /org/service-profile # set iscsi-identity {initiator-name initiator-name | initiator-pool-name iqn-pool-name |
Specifies the name of the iSCSI initiator or the name of an IQN pool from which the iSCSI initiator name will be provided. The iSCSI initiator name can be up to 223 characters. |
||
Step 14 |
UCSC(resource-mgr) /org/service-profile # set lan-connectivity-policy-name policy-name |
Associates the specified LAN connectivity policy with the service profile.
|
||
Step 15 |
UCSC(resource-mgr) /org/service-profile # set local-disk-policy policy-name |
Associates the specified local disk policy with the service profile. |
||
Step 16 |
UCSC(resource-mgr) /org/service-profile # set maintpolicyname policy-name |
Associates the specified maintenance policy with the service profile. |
||
Step 17 |
UCSC(resource-mgr) /org/service-profile # set power-control-policy policy-name |
Associates the specified power control policy with the service profile. |
||
Step 18 |
UCSC(resource-mgr) /org/service-profile # set san-connectivity-policy-name policy-name |
Associates the specified SAN connectivity policy with the service profile.
|
||
Step 19 |
UCSC(resource-mgr) /org/service-profile # set scrub-policy policy-name |
Associates the specified scrub policy with the service profile. |
||
Step 20 |
UCSC(resource-mgr) /org/service-profile # set sol-policy policy-name |
Associates the specified serial over LAN policy with the service profile. |
||
Step 21 |
UCSC(resource-mgr) /org/service-profile # set stats-policy policy-name |
Associates the specified statistics policy with the service profile. |
||
Step 22 |
UCSC(resource-mgr) /org/service-profile # set user-label label-name |
Specifies the user label associated with the service profile. |
||
Step 23 |
UCSC(resource-mgr) /org/service-profile # set vcon {1 | 2 | 3 | 4} select {all | assigned-only | exclude-dynamic | exclude-unassigned} |
Specifies the selection preference for the specified vCon. |
||
Step 24 |
UCSC(resource-mgr) /org/service-profile # set vcon-policy policy-name |
Associates the specified vNIC/vHBA placement policy with the service profile.
|
||
Step 25 |
UCSC(resource-mgr) /org/service-profile # commit-buffer |
Commits the transaction to the system configuration. |
Example
The following example shows how to create a service profile and commit the transaction:
UCSC# connect resource-mgr
UCSC(resource-mgr)# scope org /
UCSC(resource-mgr) /org* # create service-profile GSP2 instance
UCSC(resource-mgr) /org/service-profile* # set bios-policy biospol1
UCSC(resource-mgr) /org/service-profile* # set boot-policy bootpol32
UCSC(resource-mgr) /org/service-profile* # set descr "This is a global service profile example."
UCSC(resource-mgr) /org/service-profile* # set dynamic-vnic-conn-policy mydynvnicconnpolicy
UCSC(resource-mgr) /org/service-profile* # set extippoolname myippool
UCSC(resource-mgr) /org/service-profile* # set extipstate pooled
UCSC(resource-mgr) /org/service-profile* # set host-fw-policy ipmi-user987
UCSC(resource-mgr) /org/service-profile* # set identity dynamic-uuid derived
UCSC(resource-mgr) /org/service-profile* # set ipmi-access-profile ipmiProf16
UCSC(resource-mgr) /org/service-profile* # set local-disk-policy localdiskpol33
UCSC(resource-mgr) /org/service-profile* # set maintpolicyname maintpol4
UCSC(resource-mgr) /org/service-profile* # set power-control-policy powcontrpol13
UCSC(resource-mgr) /org/service-profile* # set scrub-policy scrubpol55
UCSC(resource-mgr) /org/service-profile* # set sol-policy solpol2
UCSC(resource-mgr) /org/service-profile* # set stats-policy statspol4
UCSC(resource-mgr) /org/service-profile* # set user-label mylabel
UCSC(resource-mgr) /org/service-profile* # set vcon-policy myvconnpolicy
UCSC(resource-mgr) /org/service-profile* # commit-buffer
UCSC(resource-mgr) /org/service-profile #
What to do next
Deploy the Global Service profile in UCS Domains.
Creating a Global Service Profile Instance from a Service Profile Template
Before you begin
Verify that there is a service profile template from which to create a service profile instance.
Procedure
Command or Action | Purpose | |
---|---|---|
Step 1 |
UCSC# connect resource-mgr |
Enters resource manager mode. |
Step 2 |
UCSC(resource-mgr) # scope org |
Enters organization mode for the specified organization. To enter the root organization mode, type / as the org-name . |
Step 3 |
UCSC(resource-mgr)# /org # create service-profile profile-name instance |
Creates the specified service profile and enters organization service profile mode. This name can be between 2 and 32 alphanumeric characters. You cannot use spaces or any special characters other than - (hyphen), _ (underscore), : (colon), and . (period), and this name must be unique across all service profiles and service profile templates within the same organization. |
Step 4 |
UCSC(resource-mgr) /org/service-profile # set src-templ-name profile-name |
Specifies the source service profile template to apply to the service profile instance. All configuration settings from the service profile template will be applied to the service profile instance. |
Step 5 |
UCSC(resource-mgr) /org/service-profile # commit-buffer |
Commits the transaction to the system configuration. |
Example
The following example shows how to create a service profile instance, apply the service profile template named ServTemp2, and commit the transaction:
UCSC# connect resource-mgr
UCSC(resource-mgr)# scope org /
UCSC(resource-mgr) /org* # create service-profile GSP2 instance
UCSC(resource-mgr) /org/service-profile* # set src-templ-name ServTemp2
UCSC(resource-mgr) /org/service-profile* # commit-buffer
UCSC(resource-mgr) /org/service-profile #
What to do next
Associate the service profile to a server, rack server, or server pool.
Configuring a vNIC for a Global Service Profile
Procedure
Command or Action | Purpose | |||
---|---|---|---|---|
Step 1 |
UCSC# connect resource-mgr |
Enters resource manager mode. |
||
Step 2 |
UCSC(resource-mgr) # scope org |
Enters organization mode for the specified organization. To enter the root organization mode, type / as the org-name . |
||
Step 3 |
UCSC(resource-mgr) /org # scope service-profile profile-name |
Enters organization service profile mode for the specified service profile. |
||
Step 4 |
UCSC(resource-mgr) /org/service-profile # create vnic vnic-name [eth-if eth-if-name] [fabric {a | b}] |
Creates a vNIC for the specified service profile and enters organization service profile vNIC mode. |
||
Step 5 |
UCSC(resource-mgr) /org/service-profile/vnic # set adapter-policy policy-name |
Specifies the adapter policy to use for the vNIC. |
||
Step 6 |
UCSC(resource-mgr) /org/service-profile/vnic # set fabric {a | a-b | b | b-a} |
Specifies the fabric to use for the vNIC. If you did not specify the fabric when creating the vNIC template in Step 3, you have the option to specify it with this command. If you want this vNIC to be able to access the second fabric interconnect if the default one is unavailable, choose a-b (A is the primary) or b-a (B is the primary) .
|
||
Step 7 |
UCSC(resource-mgr) /org/service-profile/vnic # set identity {dynamic-mac {mac-addr | derived} | mac-pool mac-pool-name} |
Specifies the identity (MAC address) for the vNIC. You can set the identity using one of the following options:
|
||
Step 8 |
UCSC(resource-mgr) /org/service-profile/vnic # set mtu size-num |
The maximum transmission unit, or packet size, that this vNIC accepts. Enter an integer between 1500 and 9216.
|
||
Step 9 |
UCSC(resource-mgr) /org/service-profile/vnic # set nw-control-policy policy-name |
The network control policy the vNIC should use. |
||
Step 10 |
UCSC(resource-mgr) /org/service-profile/vnic # set order {order-num | unspecified} |
Specifies the relative order for the vNIC. |
||
Step 11 |
UCSC(resource-mgr) /org/service-profile/vnic # set pin-group group-name |
The LAN pin group the vNIC should use. |
||
Step 12 |
UCSC(resource-mgr) /org/service-profile/vnic # set qos-policy policy-name |
The quality of service policy the vNIC should use. |
||
Step 13 |
UCSC(resource-mgr) /org/service-profile/vnic # set stats-policy policy-name |
The statistics collection policy the vNIC should use. |
||
Step 14 |
UCSC(resource-mgr) /org/service-profile/vnic # set template-name policy-name |
Specifies the dynamic vNIC connectivity policy to use for the vNIC. |
||
Step 15 |
UCSC(resource-mgr) /org/service-profile/vnic # set vcon {1 | 2 | 3 | 4 | any} |
Assigns the vNIC to the specified vCon. Use the any keyword to have Cisco UCS Central automatically assign the vNIC. |
||
Step 16 |
UCSC(resource-mgr) /org/service-profile/vnic # commit-buffer |
Commits the transaction to the system configuration. |
Example
The following example shows how to configure a vNIC for a service profile and commits the transaction:
UCSC# connect resource-mgr
UCSC(resource-mgr)# scope org /
UCSC(resource-mgr) /org* # scope service-profile ServProf2
UCSC(resource-mgr) /org/service-profile* # create vnic vnic3 fabric a
UCSC(resource-mgr) /org/service-profile/vnic* # set adapter-policy AdaptPol2
UCSC(resource-mgr) /org/service-profile/vnic* # set fabric a-b
UCSC(resource-mgr) /org/service-profile/vnic* # set identity mac-pool MacPool3
UCSC(resource-mgr) /org/service-profile/vnic* # set mtu 8900
UCSC(resource-mgr) /org/service-profile/vnic* # set nw-control-policy ncp5
UCSC(resource-mgr) /org/service-profile/vnic* # set order 0
UCSC(resource-mgr) /org/service-profile/vnic* # set pin-group EthPinGroup12
UCSC(resource-mgr) /org/service-profile/vnic* # set qos-policy QosPol5
UCSC(resource-mgr) /org/service-profile/vnic* # set stats-policy StatsPol2
UCSC(resource-mgr) /org/service-profile/vnic* # set template-name VnicConnPol3
UCSC(resource-mgr) /org/service-profile/vnic* # set vcon any
UCSC(resource-mgr) /org/service-profile/vnic* # commit-buffer
UCSC(resource-mgr) /org/service-profile/vnic #
Configuring a vHBA for a Global Service Profile
Procedure
Command or Action | Purpose | |
---|---|---|
Step 1 |
UCSC# connect resource-mgr |
Enters resource manager mode. |
Step 2 |
UCSC(resource-mgr) # scope org |
Enters organization mode for the specified organization. To enter the root organization mode, type / as the org-name . |
Step 3 |
UCSC(resource-mgr) /org # scope service-profile profile-name |
Enters organization service profile mode for the specified service profile. |
Step 4 |
UCSC(resource-mgr) /org/service-profile # create vhba vhba-name [fc-if fc-if-name] [fabric {a | b}] |
Creates a vHBA for the specified service profile and enters organization service profile vHBA mode. |
Step 5 |
UCSC(resource-mgr) /org/service-profile/vhba # set adapter-policy policy-name |
Specifies the adapter policy to use for the vHBA. |
Step 6 |
UCSC(resource-mgr) /org/service-profile/vhba # set fabric {a | b} |
Specifies the fabric to use for the vHBA. If you did not specify the fabric when creating the vHBA template in Step 4, you have the option to specify it with this command. |
Step 7 |
UCSC(resource-mgr) /org/service-profile/vhba # set fc-if fc-if-name |
Specifies the fibre channel interface to use for the vHBA. If you did not specify the fibre channel interface when creating the vHBA template in Step 4, you have the option to specify it with this command. |
Step 8 |
UCSC(resource-mgr) /org/service-profile/vhba # set identity {dynamic-wwpn {wwpn | derived} | wwpn-pool wwn-pool-name} |
Specifies the WWPN for the vHBA. You can set the storage identity using one of the following options:
|
Step 9 |
UCSC(resource-mgr) /org/service-profile/vhba # set max-field-size size-num |
Specifies the maximum size of the Fibre Channel frame payload (in bytes) that the vHBA supports. |
Step 10 |
UCSC(resource-mgr) /org/service-profile/vhba # set pers-bind {disabled | enabled} |
Disables or enables persistent binding to Fibre Channel targets. |
Step 11 |
UCSC(resource-mgr) /org/service-profile/vhba # set pin-group group-name |
Specifies the SAN pin group to use for the vHBA. |
Step 12 |
UCSC(resource-mgr) /org/service-profile/vhba # set qos-policy policy-name |
Specifies the QoS policy to use for the vHBA. |
Step 13 |
UCSC(resource-mgr) /org/service-profile/vhba # set stats-policy policy-name |
Specifies the statistics threshold policy to use for the vHBA. |
Step 14 |
UCSC(resource-mgr) /org/service-profile/vhba # set template-name policy-name |
Specifies the vHBA template to use for the vHBA. |
Step 15 |
UCSC(resource-mgr) /org/service-profile/vhba # set vcon {1 | 2 | 3 | 4 | any} |
Assigns the vHBA to the specified vCon. Use the any keyword to have Cisco UCS Central automatically assign the vHBA. |
Step 16 |
UCSC(resource-mgr) /org/service-profile/vhba # commit-buffer |
Commits the transaction to the system configuration. |
Example
The following example configures a vHBA for a service profile and commits the transaction:
UCSC# connect resource-mgr
UCSC(resource-mgr)# scope org /
UCSC(resource-mgr) /org* # scope service-profile ServProf2
UCSC(resource-mgr) /org/service-profile* # create vhba vhba3 fabric a
UCSC(resource-mgr) /org/service-profile/vhba* # set adapter-policy AdaptPol2
UCSC(resource-mgr) /org/service-profile/vhba* # set identity wwpn-pool wwpnPool3
UCSC(resource-mgr) /org/service-profile/vhba* # set max-field-size 8900
UCSC(resource-mgr) /org/service-profile/vhba* # set pin-group EthPinGroup12
UCSC(resource-mgr) /org/service-profile/vhba* # set qos-policy QosPol5
UCSC(resource-mgr) /org/service-profile/vhba* # set stats-policy StatsPol2
UCSC(resource-mgr) /org/service-profile/vhba* # set template-name vHBATemp3
UCSC(resource-mgr) /org/service-profile/vhba* # set vcon any
UCSC(resource-mgr) /org/service-profile/vhba* # commit-buffer
UCSC(resource-mgr) /org/service-profile/vhba #
Setting up an Inband Pooled Management IP Address
You can set up an inband pooled IPv4 or an IPv6 management address.
Procedure
Command or Action | Purpose | |
---|---|---|
Step 1 |
UCSC# scope system |
Enters System mode. |
Step 2 |
UCSC/System#scope orgorg-name |
|
Step 3 |
UCSC/org#scope service-profileservice-profile-name |
|
Step 4 |
UCSC/org/service-profile#create mgmt-ifaceinband |
|
Step 5 |
UCSC/org/service-profile/mgmt-iface#create mgmt-vlan |
|
Step 6 |
UCSC/org/service-profile/mgmt-iface/mgmt-vlan#create ext-pooled-ip |
|
Step 7 |
UCSC/org/service-profile/mgmt-iface/mgmt-vlan/ext-pooled-ip#set nameipv4-address-pool-name |
|
Step 8 |
UCSC/org/service-profile/mgmt-iface/mgmt-vlan/ext-pooled-ip#exit |
|
Step 9 |
UCSC/org/service-profile/mgmt-iface/mgmt-vlan#create ext-pooled-ip6 |
|
Step 10 |
UCSC/org/service-profile/mgmt-iface/mgmt-vlan/ext-pooled-ip6#set nameipv6-address-pool-name |
|
Step 11 |
UCSC/org/service-profile/mgmt-iface/mgmt-vlan/ext-pooled-ip6#commit-buffer |
|
Example
UCSC#scope system
UCSC/system#scope org org1
UCSC/org# scope service-profile sp2
UCSC/org/service-profile# create mgmt-iface inband1
UCSC/org/service-profile/mgmt-iface#create mgmt-vlan
UCSC/org/service-profile/mgmt-iface/mgmt-vlan# create ext-pooled-ip
UCSC/org/service-profile/mgmt-iface/mgmt-vlan/ext-pooled-ip# set name <ipv4-address-pool-name>
UCSC/org/service-profile/mgmt-iface/mgmt-vlan/ext-pooled-ip# exit
UCSC/org/service-profile/mgmt-iface/mgmt-vlan/ext-pooled-ip# create ext-pooled-ip6
UCSC/org/service-profile/mgmt-iface/mgmt-vlan/ext-pooled-ip6# set name <ipv6-address-pool-name>
UCSC/org/service-profile/mgmt-iface/mgmt-vlan/ext-pooled-ip6# commit-buffer
What to do next
Associate the inband management IP interface service profile to a server.
Setting up an Inband Static Management IP Address
You can set up an inband static IPv4 or an IPv6 management address.
Procedure
Command or Action | Purpose | |
---|---|---|
Step 1 |
UCSC# scope system |
Enters System mode. |
Step 2 |
UCSC/System#scope orgorg-name |
|
Step 3 |
UCSC/org#scope service-profileservice-profile-name |
|
Step 4 |
UCSC/org/service-profile#create mgmt-ifaceinband |
|
Step 5 |
UCSC/org/service-profile/mgmt-iface#create mgmt-vlan |
|
Step 6 |
UCSC/org/service-profile/mgmt-iface/mgmt-vlan#create ext-static-ip |
|
Step 7 |
UCSC/org/service-profile/mgmt-iface/mgmt-vlan/ext-static-ip#set addressipv4-address |
|
Step 8 |
UCSC/org/service-profile/mgmt-iface/mgmt-vlan/ext-static-ip#set default-gwgateway-ip |
|
Step 9 |
UCSC/org/service-profile/mgmt-iface/mgmt-vlan/ext-static-ip#set prefixprefix |
|
Step 10 |
UCSC/org/service-profile/mgmt-iface/mgmt-vlan/ext-static-ip#exit |
|
Step 11 |
UCSC/org/service-profile/mgmt-iface/mgmt-vlan#create ext-static-ip6 |
|
Step 12 |
UCSC/org/service-profile/mgmt-iface/mgmt-vlan/ext-static-ip6#set addressipv6-address |
|
Step 13 |
UCSC/org/service-profile/mgmt-iface/mgmt-vlan/ext-static-ip6#set default-gwgateway-ipv6 |
|
Step 14 |
UCSC/org/service-profile/mgmt-iface/mgmt-vlan/ext-static-ip6#set prefixprefix |
|
Step 15 |
UCSC/org/service-profile/mgmt-iface/mgmt-vlan/ext-static-ip6#commit-buffer |
|
Example
UCSC#scope system
UCSC/system#scope org org1
UCSC/org# scope service-profile sp2
UCSC/org/service-profile# create mgmt-iface inband1
UCSC/org/service-profile/mgmt-iface#create mgmt-vlan
UCSC/org/service-profile/mgmt-iface/mgmt-vlan# create ext-static-ip
UCSC/org/service-profile/mgmt-iface/mgmt-vlan/ext-static-ip# set addr <ipv4-address>
UCSC/org/service-profile/mgmt-iface/mgmt-vlan/ext-static-ip# set default-gw <gateway-ip>
UCSC/org/service-profile/mgmt-iface/mgmt-vlan/ext-static-ip# set prefix <prefix>
UCSC/org/service-profile/mgmt-iface/mgmt-vlan/ext-pooled-ip# exit
UCSC/org/service-profile/mgmt-iface/mgmt-vlan# create ext-static-ip6
UCSC/org/service-profile/mgmt-iface/mgmt-vlan/ext-static-ip6# set addr <ipv6-address>
UCSC/org/service-profile/mgmt-iface/mgmt-vlan/ext-static-ip6# set default-gw <gateway-ipv6>
UCSC/org/service-profile/mgmt-iface/mgmt-vlan/ext-static-ip6# set prefix <prefix>
UCSC/org/service-profile/mgmt-iface/mgmt-vlan/ext-pooled-ip6# commit-buffer
What to do next
Associate the inband management IP interface service profile to a server.
Setting up an Outband Pooled Management IP Address
You can set up an outband pooled management IPv4 address.
Procedure
Command or Action | Purpose | |
---|---|---|
Step 1 |
UCSC# scope system |
Enters System mode. |
Step 2 |
UCSC/System#scope orgorg-name |
|
Step 3 |
UCSC/org#scope service-profileservice-profile-name |
|
Step 4 |
UCSC/org/service-profile#set ext-mgmt-ip-state pooled |
|
Step 5 |
UCSC/org/service-profile#set ext-mgmt-ip-pool-namepool-name |
|
Step 6 |
UCSC/org/service-profile#commit-buffer |
|
Example
UCSC#scope system
UCSC/system#scope org org1
UCSC/org# scope service-profile sp1
UCSC/org/service-profile# set ext-mgmt-ip-state pooled
UCSC/org/service-profile#set ext-mgmt-ip-pool-name ipool1
UCSC/org/service-profile# commit-buffer
Setting up an Outband Static Management IP Address
You can set up a static outband management IP address.
Procedure
Command or Action | Purpose | |
---|---|---|
Step 1 |
UCSC# scope system |
Enters System mode. |
Step 2 |
UCSC/System#scope orgorg-name |
|
Step 3 |
UCSC/org#scope service-profileservice-profile-name |
|
Step 4 |
UCSC/org/service-profile#set ext-mgmt-ip-state static |
|
Step 5 |
UCSC/org/service-profile#create ext-static-ip |
|
Step 6 |
UCSC/org/service-profile/ext-static-ip#set addrip-address |
|
Step 7 |
UCSC/org/service-profile/ext-static-ip#set default-gwgateway ip-address |
|
Step 8 |
UCSC/org/service-profile/ext-static-ip#commit-buffer |
|
Example
UCSC#scope system
UCSC/system#scope org org1
UCSC/org# scope service-profile sp1
UCSC/org/service-profile# set ext-mgmt-ip-state static
UCSC/org/service-profile# create ext-static-ip
UCSC/org/service-profile/ext-static-ip#set addr <ip-address>
UCSC/org/service-profile/ext-static-ip#set default-gw <gateway ip-address>
UCSC/org/service-profile/ext-static-ip# commit-buffer
Deleting a Global Service Profile
Procedure
Command or Action | Purpose | |
---|---|---|
Step 1 |
UCSC# connect resource-mgr |
Enters resource manager mode. |
Step 2 |
UCSC(resource-mgr) # scope org |
Enters organization mode for the specified organization. To enter the root organization mode, type / as the org-name . |
Step 3 |
UCSC(resource-mgr)# /org # show service-profile |
Displays the existing service profiles and service profile templates. |
Step 4 |
UCSC(resource-mgr)# /org # delete service-profile profile-name |
Deletes the specified service profile. |
Step 5 |
UCSC(resource-mgr) /org # commit-buffer |
Commits the transaction to the system configuration. |
Example
The following example shows how to delete a service profile and commit the transaction:
UCSC# connect resource-mgr
UCSC(resource-mgr)# scope org /
UCSC(resource-mgr) /org # show service-profile
Service Profile:
Service Profile Name Type System Id Server Assignment Association
-------------------- ----------------- ---------- --------- ---------- -----------
GSP_temp Initial Template Unassigned Unassociated
GSP2 Instance Unassigned Unassociated
test-upd_temp Updating Template Unassigned Unassociated
test2 Instance Unassigned Unassociated
UCSC(resource-mgr) /org* # delete service-profile GSP2
UCSC(resource-mgr) /org* # commit-buffer
UCSC(resource-mgr) /org #