Call Termination Cause Codes

Revised: May 14, 2012, OL-24995-02

Introduction

This appendix lists call termination cause values and definitions.

BTS 10200 Call Termination Cause Values and Definitions

Table A-1 lists the BTS 10200 call termination cause values and definitions.

Note A "*" next to the value in Table A-1 indicates the cause code is not a standard BAF cause code; it is unique to the Cisco BTS 10200 Softswitch. All values of 400 or higher are used internally only and do not appear in the billing records transmitted from the EMS.

Table A-1 Call Termination Cause Values and Definitions 

Value
Cause Definition
In Release 6.0.1

1

Attempted termination to an unallocated or unassigned directory number.

Yes

2

No route available to the specified transit network.

Yes

3

No route available to the specified destination.

Yes

4

Vacant code.

Yes

6

Channel unacceptable.

Yes

7

Call awarded and being delivered in an established channel.

Yes

8

Prefix 0 was dialed in error.

Yes

9

Prefix 1 was dialed in error.

Yes

10

Prefix 1 was not dialed when required.

Yes

11

Excessive digits received, call is progressing.

Yes

12

Call is proceeding.

Yes

13

The requested service was denied.

Yes

14

Indicates an exchange detected that the called number was ported out.

Yes

16

Normal call clearing.

Yes

17

Termination called is busy.

Yes

18

No user responding.

Yes

19

User altering, no answer.

Yes

21

Call was rejected.

Yes

22

The terminating number was changed.

Yes

23

Terminating party rejects all calls with Calling Line Identification Restriction.

Yes

24

The destination business group is not defined.

Yes

25*

Exchange routing error occurred.

Yes

26*

For ANSI calls, the destination is misrouted because the number is ported out of the switch.

For ISDN calls, the destination is able to accept calls but no user is assigned to the endpoint.

Yes

27

The specified destination was out of order.

Yes

28

Invalid number format or incomplete address.

Yes

29

Facility rejected.

Yes

30

Response to STATUS ENQ message.

Yes

31

Normal, unspecified.

Yes

34

Circuit or channel congestion.

Yes

35

Requested VPCI/VCI was not available.

Yes

36

VPCI/VCI assignment failure.

Yes

37

The user cell rate was unavailable.

Yes

38*

Network out of order.

Yes

39

The destination Permanent Virtual Circuit (PVC) is out of order.

Yes

41

Temporary failure.

Yes

42

Switching Equipment Congestion.

Yes

43

Access information discarded.

Yes

44

Requested channel not available.

Yes

45

No VPCI/VCI available.

Yes

46

Precedence call blocked.

Yes

47

Network resource unavailable or unspecified.

Yes

49

Quality of service unavailable.

Yes

50

Requested facility not subscribed to.

Yes

51

Bearer capability incompatible with service request.

Yes

53

Service operation violated.

Yes

57

Bearer capability not authorized.

Yes

58

Bearer capability not presently available.

Yes

63

Service or option unspecified.

Yes

65

Bearer capability not implemented.

Yes

66*

Channel type not implemented.

No

69

Requested facility not implemented.

Yes

70

Restoration digital bearer capacity only available.

No

73

Unsupported combination of traffic parameters.

Yes

78

AAL parameter cannot be supported.

Yes

79

Service or option not implemented.

Yes

81

Invalid call reference value.

Yes

82

Identified channel does not exist.

Yes

84*

Call id already in use.

No

85*

No call suspended.

No

86*

Call id cleared.

No

88

Incompatible destination.

Yes

89

Invalid endpoint reference.

Yes

90*

Unspecified invalid message error.

No

91

Invalid transit network selection.

Yes

92

Too many pending add party requests.

Yes

96

Mandatory information element missing.

Yes

97

Message type nonexistent or not implemented.

Yes

98*

Message type not compatible.

No

99

Information element nonexistent or not implemented.

Yes

100

Invalid information element contents.

Yes

101

Message not compatible with call state.

Yes

102

Recovery on timer expiration.

Yes

104

Incorrect message length.

Yes

111

Protocol error - unspecified.

Yes

112

Protocol error - threshold exceeded.

Yes

120

Special intercept announcement.

No

121

Special intercept announcement—undefined code.

No

122

Special intercept announcement—call blocked due to group restriction.

No

127

Interworking error—unspecified.

Yes

150

Call Terminated due to Session Timer Refresh Request Time Out.

Yes

901

NE Cause Audit Release.

Yes


BTS 10200 Bye Message Cause Code to GR-1100 Cause Code Mapping

The call termination cause code contained in a CDR is a mapping of the BTS 10200 call termination code to a GR-1100 code. In several cases, the cause code used during call processing does not map directly into a GR-1100. In these instances, the mapping shown in Table A-2is performed to generate the CDR call termination cause code:

Table A-2 BTS 10200 Bye Message Cause Code to GR-1100 Cause Code Mapping 

Bye
Message
Cause
Code
Bye Message Cause Code Definition
Mapped
BAF
GR-1100
Cause
Code
Mapped BAF GR-1100 Cause Code Definition

5

CA CCITT NE CAUSE TRUNKPREF MISDIAL

41

TEMPORARY FAILURE

8

CA ANSI NE CAUSE PREFIX 0 ERROR

8

ZERO DIALED IN ERROR

20

CA CCITT NE SUBSCRIBER ABSENT

1

UNASSIGNED NUMBER

23

CA ANSI NE DEST NUMBER UNALLOCATED

1

UNASSIGNED NUMBER

24

CA ANSI NE BUSINESS GRP UNDEFINED

1

UNASSIGNED NUMBER

25

CA ANSI NE CAUSE EXCHG ROUTE ERROR

47

RESOURCE UNAVAILABLE

38

CA CCITT NRU CAUSE NET OUTOFORDER

47

RESOURCE UNAVAILABLE

39

CA CCITT NRU CAUSE PVC OUTOFORDER

47

RESOURCE UNAVAILABLE

46

CA CCITT NRU PRECEDENCE CALL BLOCKED

21

CALL REJECTED

54

CA ANSI SNA GRP RESTR CALL BLOCKED

21

CALL REJECTED

55

CA CCITT SNA IN CUG CALL BARRED

21

CALL REJECTED

62

CA CCITT SNA CAUSE SERVICE INCONSISTENCY

13

SERVICE DENIED

66

CA CCITT SNI CAUSE CHANNELTYPE UNIMPLEMENTED

65

BEARER CAPABILITY NOT IMPLEMENTED

70

CA CCITT SNI CAUSE RESTDIGITAL BEARERCAP ONLYAVAIL

49

QOS UNAVAILABLE

83

CA CCITT IM CAUSE SUSP CALLID NOTEXIST

31

NORMAL UNSPECIFIED

84

CA CCITT IM CAUSE CALLID INUSE

31

NORMAL UNSPECIFIED

85

CA CCITT IM CAUSE NOCALL SUSPENDED

31

NORMAL UNSPECIFIED

86

CA CCITT IM CAUSE CALLID CLEARED

31

NORMAL UNSPECIFIED

87

CA CCITT IM CAUSE USER NOT CUG MEMBER

31

NORMAL UNSPECIFIED

90

CA CCITT IM CAUSE CUG NOT EXIST

31

NORMAL UNSPECIFIED

95

CA CCITT IM CAUSE UNSPECIFIED

31

NORMAL UNSPECIFIED

98

CA CCITT PE CAUSE MSGTYPE NOTCOMPAT

101

MESSAGE INCOMPATIBLE WITH CALLSTATE

103

CA CCITT PE CAUSE NOTEXIST UNIMPL PARAM PASSON

100

INVALID INFOELEMENT

110

CA CCITT PE CAUSE UNRECOGNIZE PARAM DISCARD

100

INVALID INFOELEMENT