Configuring the Cisco Unified SIP Proxy
Last updated: October 10, 2019
Configuring Logical Networks
Each interface on the Cisco Unified SIP Proxy is associated with a logical network. Logical networks are used to organize server groups, listen points, and other properties. SIP messages are associated with the network on which they arrive.
Summary Steps
1.
cusp
2.
configure
3.
sip network network
4.
end network
Detailed Steps
|
|
|
Step 1 |
cusp
se-10-0-0-0> cusp |
Enters Cisco Unified SIP Proxy EXEC mode. |
Step 2 |
configure
se-10-0-0-0(cusp)> configure |
Enters Cisco Unified SIP Proxy configuration mode. |
Step 3 |
sip network network
se-10-0-0-0(cusp-config)> sip network service-provider |
Creates a network and puts you into network command mode. In this case, the network that is being created is called “service provider”. |
Step 4 |
end network
se-10-0-0-0(cusp-config-network)> end network |
Exits network command mode. |
Example
The following example creates a network called “service-provider”:
se-10-0-0-0(cusp)> configure
se-10-0-0-0(cusp-config)> sip network service-provider
se-10-0-0-0(cusp-config-network)> end network
Configuring Trigger Conditions
You create trigger conditions to allow Cisco Unified SIP Proxy to respond with the appropriate action for various call flows. In general, the more complex the call flow is, the more complex the trigger must be.
Summary Steps
1.
cusp
2.
configure
3.
trigger condition trigger-condition-name
4.
sequence sequence-number
5.
(Optional) in-network network-name
6.
(Optional) mid-dialog
7.
end sequence
8.
end trigger condition
Detailed Steps
|
|
|
Step 1 |
cusp
se-10-0-0-0> cusp |
Enters Cisco Unified SIP Proxy EXEC mode. |
Step 2 |
configure
se-10-0-0-0(cusp)> configure |
Enters Cisco Unified SIP Proxy configuration mode. |
Step 3 |
trigger condition trigger-condition-name
se-10-0-0-0(cusp-config)> trigger condition call-from-service-provider |
Creates a trigger condition and puts you into trigger command mode. In this case, the trigger that is being created is called “call-from-service-provider”. |
Step 4 |
sequence sequence-number
se-10-0-0-0(cusp-config-trigger)> sequence 1 |
Creates a sequence with the specified number and puts you into trigger sequence command mode. The number indicates the order in which triggers are evaluated. In this case, the sequence that is being created is sequence number 1. |
Step 5 |
in-network network-name
se-10-0-0-0(cusp-config-trigger-seq)> in-network service-provider |
Optional. Specifies the incoming network name for the trigger condition. In this case, the incoming network is the “service-provider” network. |
Step 6 |
mid-dialog
se-10-0-0-0(cusp-config-trigger-seq)> mid-dialog |
Optional. A special trigger that bypasses routing policies on mid-dialog messages. |
Step 7 |
end sequence
se-10-0-0-0(cusp-config-trigger-seq)> end sequence |
Exits the trigger sequence command mode. |
Step 8 |
end trigger condition
se-10-0-0-0(cusp-config-trigger)> end trigger condition |
Exits the trigger command mode. |
Example
In this example, Cisco Unified SIP Proxy only reacts based on the network the call came in on, so the triggers are simple.
se-10-0-0-0(cusp)> configure
se-10-0-0-0(cusp-config)> trigger condition call-from-service-provider
se-10-0-0-0(cusp-config-trigger)> sequence 1
se-10-0-0-0(cusp-config-trigger-seq)> in-network service-provider
se-10-0-0-0(cusp-config-trigger-seq)> end sequence
se-10-0-0-0(cusp-config-trigger)> end trigger condition
se-10-0-0-0(cusp-config)> trigger condition mid-dialog
se-10-0-0-0(cusp-config-trigger)> sequence 1
se-10-0-0-0(cusp-config-trigger-seq)> mid-dialog
se-10-0-0-0(cusp-config-trigger-seq)> end sequence
se-10-0-0-0(cusp-config-trigger)> end trigger condition
Configuring Server Groups
About Server Groups
Server groups define the elements that Cisco Unified SIP Proxy interacts with for each network. The server group name that is used is inserted into the SIP URI of the outgoing request. Some devices, such as Cisco Unified Communications Manager, validate the URI of requests before processing, which means that the end device might need to be configured with a Fully Qualified Domain Name (FQDN) to allow for this.
Two of the fields for each individual element, q-value and weight, are important to use to specify the priorities of elements, and also for load balancing. Calls are routed to specific elements based on q-value. The element with the highest q-value receives all traffic routed to that server group. If multiple elements have the same q-value, traffic is distributed between them based on the load-balancing option used. The default load-balancing is based on call-id, but weight can also be used. If weight is used, the percentage of traffic that an element receives is equal to its weight divided by the sum of up elements with the same q-value's weights. The sum of their weights does not need to equal 100. You can change the weights and q-values to configure a different priority or load-balancing scheme.
Summary Steps
1.
cusp
2.
configure
3.
server-group sip group server-group-name network
4.
element ip-address ipaddress port {udp | tcp | tls} [q-value q-value ] [weight weight ]
5.
lb-type {global | highest-q | request-uri | call-id | to-uri | weight }
6.
end server-group
Detailed Steps
|
|
|
Step 1 |
cusp
se-10-0-0-0> cusp |
Enters Cisco Unified SIP Proxy EXEC mode. |
Step 2 |
configure
se-10-0-0-0(cusp)> configure |
Enters Cisco Unified SIP Proxy configuration mode. |
Step 3 |
server-group sip group server-group-name network
se-10-0-0-0(cusp-config)> server-group sip group sp.example.com service-provider |
Creates a SIP server group and enters server group command mode. In this case, the server group being created is called “sp.example.com” and it uses the network called “service-provider”. |
Step 4 |
element ip-address ipaddress port {udp | tcp | tls} [q-value q-value ] [weight weight ]
se-10-0-0-0(cusp-config-sg)> element ip-address 192.168.10.3 5060 tls q-value 1.0 weight 100 |
Creates an IP element for a SIP server group and determines the characteristics of the SIP server group. Note You can enter this command multiple times. |
Step 5 |
lb-type {global | highest-q | request-uri | call-id | to-uri | weight }
se-10-0-0-0(cusp-config-sg)> lb-type weight |
Configures the load-balancing algorithm for the SIP server group. In this example, it specifies that the element will be selected proportional to its weight relative to the weights of other elements of the same q-value. |
Step 6 |
end server-group
se-10-0-0-0(cusp-config-sg)> end server-group |
Exits the server group command mode. |
Example
se-10-0-0-0(cusp)> configure
se-10-0-0-0(cusp-config)> server-group sip group sp.example.com service-provider
se-10-0-0-0(cusp-config-sg)> element ip-address 192.168.10.3 5060 tls q-value 1.0 weight 100
se-10-0-0-0(cusp-config-sg)> element ip-address 192.168.10.4 5060 tls q-value 1.0 weight 50
se-10-0-0-0(cusp-config-sg)> element ip-address 192.168.10.5 5060 tls q-value 1.0 weight 50
se-10-0-0-0(cusp-config-sg)> lb-type weight
se-10-0-0-0(cusp-config-sg)> end server-group
Configuring Route Tables
About Route Tables
You must configure route tables to direct SIP requests to their appropriate destinations. Each route table consists of a set of keys that are matched based on the lookup policy. For example, each key might represent the prefix of a phone number dialed.
Summary Steps
1.
cusp
2.
configure
3.
route table table-name
4.
key key response response-code
5.
key key target-destination target-destination network
6.
end route table
Detailed Steps
|
|
|
Step 1 |
cusp
se-10-0-0-0> cusp |
Enters Cisco Unified SIP Proxy EXEC mode. |
Step 2 |
configure
se-10-0-0-0(cusp)> configure |
Enters Cisco Unified SIP Proxy configuration mode. |
Step 3 |
route table table-name
se-10-0-0-0(cusp-config)> route table service-provider-table |
Creates a route table and enters route table command mode. In this case, it creates a route table called “service-provider-table”. |
Step 4 |
key key response response-code
se-10-0-0-0(cusp-config-rt)> key * response 404 |
Assigns a response code to a lookup key. In this example, it returns a response of “404” to everything. |
Step 5 |
key key target-destination target-destination network
se-10-0-0-0(cusp-config-rt)> key 510 target-destination cube-sp.example.com cube-sp |
Replaces the key part of the target destination with a specified value. Note You can enter this command multiple times. |
Step 6 |
end route table
se-10-0-0-0(cusp-config-rt)> end route table |
Exits the route table command mode. |
Example
se-10-0-0-0(cusp)> configure
se-10-0-0-0(cusp-config)> route table service-provider-table
se-10-0-0-0(cusp-config-rt)> key * response 404
se-10-0-0-0(cusp-config-rt)> key 510 target-destination cube-sp.example.com cube-sp
se-10-0-0-0(cusp-config-rt)> end route table
Configuring Normalization Policies
Normalization policies modify SIP messages to account for incompatibilities between networks. In this case, the service provider cannot handle phone numbers with the escape sequence “91,” so the sequence must be removed from the request-uri and TO header.
Summary Steps
1.
cusp
2.
configure
3.
policy normalization policy_name
4.
uri-component update request-uri {user | host | host-port | phone | uri} {all | match-string } replace-string
5.
uri-component update header {first | last | all} {user | host | host-port | phone | uri} {all | match-string} replace-string
6.
end policy
Detailed Steps
|
|
|
Step 1 |
cusp
se-10-0-0-0> cusp |
Enters Cisco Unified SIP Proxy EXEC mode. |
Step 2 |
configure
se-10-0-0-0(cusp)> configure |
Enters Cisco Unified SIP Proxy configuration mode. |
Step 3 |
policy normalization policy-name
se-10-0-0-0(cusp-config)> policy normalization outgoing-norm-policy |
Creates a normalization policy and enters policy normalization command mode. In this example, the normalization policy is called “outgoing-norm-policy”. |
Step 4 |
uri-component update request-uri {user | host | host-port | phone | uri} {all | match-string } replace-string
se-10-0-0-0(cusp-config-norm)> uri-component update request-uri user ^91 "" |
Configures a normalization policy step that updates a URI component field within a request URI. |
Step 5 |
uri-component update header {first | last | all} {user | host | host-port | phone | uri} {all | match-string} replace-string
se-10-0-0-0(cusp-config-norm)> uri-component update TO all user ^91 "" |
Configures a normalization policy step that updates a URI component field within a header of the source message. |
Step 6 |
end policy
se-10-0-0-0(cusp-config-norm)> end policy |
Exits policy normalization command mode. |
Example
se-10-0-0-0(cusp)> configure
se-10-0-0-0(cusp-config)> policy normalization outgoing-norm-policy
se-10-0-0-0(cusp-config-norm)> uri-component update request-uri user ^91 ""
se-10-0-0-0(cusp-config-norm)> uri-component update TO all user ^91 ""
se-10-0-0-0(cusp-config-norm)> end policy
Configuring Lookup Policies
Lookup policies decide how the keys in the route tables are used. Each key represents the beginning of the phone number dialed because each policy states to match the user component of the request-uri against the keys in its route table. The user component of the request-uri is the phone number called. The rule used to match is prefix, which means that the longest prefix match in the route table is used. So if the dialed number is 510-1XX-XXXX, the call is sent to the cme.example.com server group. If the dialed number is 510-XXX-XXXX, the call is sent to the cucm.example.com server group. The four policies in the following example are identical, except that they each refer to their specific table.
Summary Steps
1.
cusp
2.
configure
3.
policy lookup policy-name
4.
sequence sequence-number table-name field { in-network | local-ip-address | local-ip-port | remote-ip-address | remote-ip-port} | header { p-asserted identity| from | to | diversion| remote-party-id } | request uri [uri component { param| user | phone | host| host-port| uri } ]
5.
rule {exact | prefix | subdomain | subnet | fixed length } [case-insensitive]
6.
end sequence
7.
end policy
Detailed Steps
|
|
|
Step 1 |
cusp
se-10-0-0-0> cusp |
Enters Cisco Unified SIP Proxy EXEC mode. |
Step 2 |
configure
se-10-0-0-0(cusp)> configure |
Enters Cisco Unified SIP Proxy configuration mode. |
Step 3 |
policy lookup policy-name
se-10-0-0-0(cusp-config)> policy lookup service-provider-policy |
Creates a policy with the specified name and enters policy lookup command mode. In this case, creates a policy called “service-provider-policy”. |
Step 4 |
sequence sequence-number table-name field {in-network | local-ip-address | local-ip-port | remote-ip-address | remote-ip-port} | header {p-asserted identity| from | to | diversion| remote-party-id} | request uri [uri component {param| user | phone | host| host-port| uri } ]
se-10-0-0-0(cusp-config-lookup)> sequence 1 |
Creates a sequence with the specified number and enters policy lookup sequence command mode. Sequences are performed according to the order of their number. |
Step 5 |
rule {exact | prefix | subdomain | subnet | fixed length } [case-insensitive]
se-10-0-0-0(cusp-config-lookup-seq)> rule prefix |
Creates a rule that determines the routing algorithm for the lookup policy. In this case, it creates a rule that specifies that the lookup policy searches for the longest prefix match. |
Step 6 |
end sequence
se-10-0-0-0(cusp-config-lookup-seq)> end sequence |
Exits policy lookup sequence command mode. |
Step 7 |
end policy
se-10-0-0-0(cusp-config-lookup)> end policy |
Exits policy lookup command mode. |
Example
se-10-0-0-0(cusp)> configure
se-10-0-0-0(cusp-config)> policy lookup service-provider-policy
se-10-0-0-0(cusp-config-lookup)> sequence 1 service-provider-table request-uri uri-component user
se-10-0-0-0(cusp-config-lookup-seq)> rule prefix
se-10-0-0-0(cusp-config-lookup-seq)> end sequence
se-10-0-0-0(cusp-config-lookup)> end policy
Configuring Routing Triggers
Routing triggers correlate trigger conditions with lookup policies. A single policy is chosen based on which corresponding condition is matched. The conditions are evaluated in ascending order based on sequence number. The mid-dialog condition is the first one so that the policy step is skipped for mid-dialog messages. Based on the following configuration, after the INVITE message is successfully routed, all subsequent messages (which are mid-dialog) bypass routing policies.
Summary Steps
1.
cusp
2.
configure
3.
trigger routing sequence sequence-number {by-pass | policy policy } [condition trigger-condition ]
Detailed Steps
|
|
|
Step 1 |
cusp
se-10-0-0-0> cusp |
Enters Cisco Unified SIP Proxy EXEC mode. |
Step 2 |
configure
se-10-0-0-0(cusp)> configure |
Enters Cisco Unified SIP Proxy configuration mode. |
Step 3 |
trigger routing sequence sequence-number {by-pass | policy policy } [condition trigger-condition ]
se-10-0-0-0(cusp-config)> trigger routing sequence 2 policy service-provider-policy condition call-from-service-provider |
Associates a routing policy with a trigger condition. In this example, the second sequence follows the previously-created policy called “service-provider-policy” and the previously-created trigger called “call-from-service-provider”. |
Example
se-10-0-0-0(cusp)> configure
se-10-0-0-0(cusp-config)> trigger routing sequence 1 by-pass condition mid-dialog
se-10-0-0-0(cusp-config)> trigger routing sequence 2 policy service-provider-policy condition call-from-service-provider
se-10-0-0-0(cusp-config)> trigger routing sequence 3 policy cube-sp-policy condition call-from-cube-sp
se-10-0-0-0(cusp-config)> trigger routing sequence 4 policy cube-es-policy condition call-from-cube-es
se-10-0-0-0(cusp-config)> trigger routing sequence 5 policy enterprise-policy condition call-from-enterprise
Configuring Normalization Triggers
Normalization triggers correlate trigger conditions with normalization policies. There are two types of triggers: pre-normalization, which occurs before routing, and post-normalization, which occurs after routing. Similar to routing policies, a special policy bypasses normalization on mid-dialog messages.
Summary Steps
1.
cusp
2.
configure
3.
trigger pre-normalization sequence sequence-number { by-pass | policy policy } [ condition trigger-condition ]
Detailed Steps
|
|
|
Step 1 |
cusp
se-10-0-0-0> cusp |
Enters Cisco Unified SIP Proxy EXEC mode. |
Step 2 |
configure
se-10-0-0-0(cusp)> configure |
Enters Cisco Unified SIP Proxy configuration mode. |
Step 3 |
trigger pre-normalization sequence sequence-number {by-pass | policy policy } [ condition trigger-condition ]
se-10-0-0-0(cusp-config)> trigger pre-normalization sequence 2 policy outgoing-norm-policy condition call-from-cube-sp |
Configures a pre-normalization algorithm for incoming SIP messages to a normalization policy. In this example, the second sequence follows the previously-created policy called “outgoing-norm-policy” and the previously-created trigger called “call-from-cube-sp”. |
Example
se-10-0-0-0(cusp)> configure
se-10-0-0-0(cusp-config)> trigger pre-normalization sequence 1 by-pass condition mid-dialog
se-10-0-0-0(cusp-config)> trigger pre-normalization sequence 2 policy outgoing-norm-policy condition call-from-cube-sp
Configuring Listen and Record-Route Ports
You must configure listen and record-route ports for each network. For the listen and record-route ports, the actual addresses of the Cisco Unified SIP Proxy module are used. The sip record-route command inserts the record-route header into outgoing requests. The sip listen command allows for Cisco Unified SIP Proxy to accept incoming requests on that port.
Summary Steps
1.
cusp
2.
configure
3.
sip record-route network_name {tcp | tls | udp} ip_address [port]
4.
sip listen network_name {tcp | tls | udp} ip_address port
Detailed Steps
|
|
|
Step 1 |
cusp
se-10-0-0-0> cusp |
Enters Cisco Unified SIP Proxy EXEC mode. |
Step 2 |
configure
se-10-0-0-0(cusp)> configure |
Enters Cisco Unified SIP Proxy configuration mode. |
Step 3 |
sip record-route network_name {tcp | tls | udp} ip_address [port]
se-10-0-0-0(cusp-config)> sip record-route service-provider udp 10.10.10.99 5060 |
Enables record-routing for a SIP network. In this example, the “service-provider” network is associated with a record-route configuration and the IP address that populates the record-route header field is “10.10.10.99” and the port that populates the record-route header is 5060. |
Step 4 |
sip listen network_name {tcp | tls | udp} ip_address port
se-10-0-0-0(cusp-config)> sip listen service-provider udp 10.10.10.99 5060 |
Creates a listener that listens for SIP traffic on a specific SIP network, host, and port. |
Example
se-10-0-0-0(cusp)> configure
se-10-0-0-0(cusp-config)> sip record-route service-provider udp 10.10.10.99 5060
se-10-0-0-0(cusp-config)> sip listen service-provider udp 10.10.10.99 5060
Configuring a Hostname
If the upstream element is using DNS SRV for routing to the two Cisco Unified SIP Proxies in a network, you must configure the two Cisco Unified SIP Proxies to have the same FQDN by entering the sip alias command in Cisco Unified SIP Proxy configuration mode on both Cisco Unified SIP Proxies.
Summary Steps
1.
cusp
2.
configure
3.
sip alias hostname
Detailed Steps
|
|
|
Step 1 |
cusp
se-10-0-0-0> cusp |
Enters Cisco Unified SIP Proxy EXEC mode. |
Step 2 |
configure
se-10-0-0-0(cusp)> configure |
Enters Cisco Unified SIP Proxy configuration mode. |
Step 3 |
sip alias hostname
se-10-0-0-0(cusp-config)> sip alias myhost |
Configures the hostname of this instance. |
Example
se-10-0-0-0(cusp)> configure
se-10-0-0-0(cusp-config)> sip alias myhost
Configuring Transport Layer Security (TLS)
Creating and Importing a Signed Certificate
Cisco Unified SIP Proxy supports TLS, Transmission Control Protocol (TCP), and User Datagram Protocol (UDP). Establishing TLS connections requires some extra steps because the connections require authentication using signed certificates.
Prerequisites
You need an FTP server or HTTP to export certificate requests.
Summary Steps
1.
configure terminal
2.
crypto key generate [rsa {label label-name | modulus modulus-size } | default]
3.
crypto key certreq label label-name url {ftp: | http:}
4.
crypto key import rsa label label-name {der url {ftp: | http: } | pem { terminal | url {ftp: | http: }} [default]
5.
crypto key import cer label mykey url ftp:
6.
offline
7.
reload
Detailed Steps
|
|
|
Step 1 |
configure terminal
se-10-0-0-0# configure terminal |
Enters configuration mode. |
Step 2 |
crypto key generate [rsa {label label-name | modulus modulus-size } | default]
se-10-0-0-0(config)> crypto key generate rsa label mykey modulus 512 default |
Creates an RSA private key. |
Step 3 |
crypto key certreq label label-name url {ftp: | http:}
se-10-0-0-0(config)> crypto key certreq label mykey url ftp: |
Creates a certificate request to be signed. |
Step 4 |
crypto key import rsa label label-name {der url {ftp: | http: } | pem { terminal | url {ftp: | http: }} [default]
se-10-0-0-0(config)> crypto key import trustcacert label rootCA url ftp: |
After the certificate request is signed, imports the trusted certificate authority (CA) certificate that you used to sign the request. |
Step 5 |
crypto key import rsa label label-name {der url {ftp: | http: } | pem { terminal | url {ftp: | http: }} [default]
se-10-0-0-0(config)> crypto key import cer label mykey url ftp: |
After the root CA is imported, imports the signed certificate. |
Step 6 |
offline
se-10-0-0-0> offline !!!WARNING!!!: Putting the system offline will terminate all active calls. Do you wish to continue[n]?: y |
Initiates Cisco Unified SIP Proxy offline mode. |
Step 7 |
reload
se-10-0-0-0(offline)> reload |
Restarts the Cisco Unified SIP Proxy system and enables Cisco Unified SIP Proxy to verify the imported trusted certificate. |
Example of Creating a Signed Certificate
se-10-0-0-0# configure terminal
se-10-0-0-0(config)> crypto key generate rsa label mykey modulus 512 default
Key generation in progress. Please wait...
The label name for the key is mykey
se-10-0-0-0(config)> crypto key certreq label mykey url ftp:
Address or name of remote host? 192.168.202.216
Username (ENTER if none)? anonymous
Destination path? netmod/mykey.csr
Uploading CSR file succeed
se-10-0-0-0(config)> crypto key import trustcacert label rootCA url ftp:
Import certificate file...
Address or name of remote host? 192.168.202.216
Source filename? netmod/rootCA/cacert.pem
se-10-0-0-0(config)> crypto key import cer label mykey url ftp:
Import certificate file...
Address or name of remote host? 192.168.202.216
Source filename? netmod/mycert.cer
What To Do Next
- Import the trusted CA certificates for any of the TLS peer elements.
Configuring TLS on Cisco Unified SIP Proxy
After you import the certificates, you must enable TLS connections. If you want more security, you can create a list of trusted peers. If you create such a list, only connections from those peers are accepted. The peer's hostname entry must be the peer's subjectAltName in its certificate. If subjectAltName is not used in the certificate, the peer's hostname entry must be CN.
Summary Steps
1.
cusp
2.
configure
3.
sip tls
4.
sip tls trusted-peer { peer’s-hostname }
5.
sip tls connection-setup-timeout {value in seconds}
Detailed Steps
|
|
|
Step 1 |
cusp
se-10-0-0-0> cusp |
Enters Cisco Unified SIP Proxy EXEC mode. |
Step 2 |
configure
se-10-0-0-0(cusp)> configure |
Enters Cisco Unified SIP Proxy configuration mode. |
Step 3 |
sip tls
se-10-0-0-0(cusp-config)> sip tls |
Enables the use of SIP TLS connections with other SIP entities, providing secure communication over the Internet. |
Step 4 |
sip tls trusted-peer { peer’s-hostname }
se-10-0-0-0(cusp-config)> sip tls trusted-peer example.com |
Creates a list of trusted peers. |
Step 5 |
sip tls connection-setup-timeout { value in seconds }
se-10-0-0-0(cusp-config)> sip tls connection-setup-timeout <1-60> |
It is the time specified in Cisco Unified SIP Proxy by the user to establish connection with the trusted peer. The default value is 1 second. The range of values is 1 to 60 seconds. |
Example of Configuring TLS
se-10-0-0-0(cusp)> configure
se-10-0-0-0(cusp-config)> sip tls
se-10-0-0-0(cusp-config)> sip tls trusted-peer example.com
se-10-0-0-0(cusp-config)> sip tls connection-setup-timeout <1-60>
Configuring Lite Mode
One of the ways you can configure the performance of the Cisco Unified SIP Proxy is to switch the module to Lite Mode. In Lite Mode, which requires you to disable record-route, the module’s performance is boosted. In standard mode, the module processes calls up to the licensed limit.
By default, the module is in standard mode.
For information on the performance difference when using Lite Mode versus standard mode, see the Release Notes for Cisco Unified SIP Proxy Release 9.1.x.
Summary Steps
1.
cusp
2.
configure
3.
lite-mode
Detailed Steps
|
|
|
Step 1 |
cusp
se-10-0-0-0> cusp |
Enters Cisco Unified SIP Proxy EXEC mode. |
Step 2 |
configure
se-10-0-0-0(cusp)> configure |
Enters Cisco Unified SIP Proxy configuration mode. |
Step 3 |
lite-mode
se-10-0-0-0(cusp-config)> lite-mode |
Puts the Cisco Unified SIP Proxy module into Lite Mode. |
Example
The following example puts the module into Lite Mode:
se-10-0-0-0(cusp)> configure
se-10-0-0-0(cusp-config)> lite-mode
Configuring Performance Control
About Performance Control
One of the ways you can configure the performance of the Cisco Unified SIP Proxy is to restrict the number of calls that the Cisco Unified SIP Proxy can handle.
Summary Steps
1.
cusp
2.
configure
3.
call-rate-limit limit
Detailed Steps
|
|
|
Step 1 |
cusp
se-10-0-0-0> cusp |
Enters Cisco Unified SIP Proxy EXEC mode. |
Step 2 |
configure
se-10-0-0-0(cusp)> configure |
Enters Cisco Unified SIP Proxy configuration mode. |
Step 3 |
call-rate-limit limit
se-10-0-0-0(cusp-config)> call-rate-limit 50 |
Sets the maximum call rate that the Cisco Unified SIP Proxy can handle. |
Example
The following example limits the number of calls that the system can process to 50:
se-10-0-0-0(cusp)> configure
se-10-0-0-0(cusp-config)> call-rate-limit 50
Committing the Configuration
Now you must commit the configuration. Committing the configuration serves two purposes: the configuration becomes active, and is persisted.
- To see the current active configuration, enter the show configuration active command.
- To see what the active configuration will be after you commit your changes, enter the show configuration candidate command.
- To commit the configuration for this example, enter the following command:
se-10-0-0-0(cusp-config)> commit